ISOGEN Symbol Key (SKEY) Definitions

Reference Guide

Version 2014 Service Pack 1 (12.0.1)

February 2014
DISO-PE-200016B-UPDATED
Copyright
Copyright © 1991-2014 Alias Limited. All rights reserved.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third
parties which is protected by copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from Alias Limited.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed at private expense and is "restricted computer software"
submitted with restricted rights in accordance with subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations
("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the United States. For units of the Department of Defense ("DoD"): This is "commercial computer
software" as defined at DFARS 252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.
Unpublished - rights reserved under the copyright laws of the United States.
Alias Limited
1 Stuart Road, Manor Park
Runcorn, Cheshire
WA7 1TS
United Kingdom
Telephone: +44 (0) 1928 579311
Fax: +44 (0) 1928 579389
Email: [email protected]

Terms of Use
It is the policy of Alias Limited to enforce any and all rights relating to protection of this information. The information contained in this manual is proprietary in nature and may not be reproduced,
copied or divulged in whole or in part without the prior written consent of Alias Limited. This manual has been provided pursuant to the terms of a contract or confidentiality agreement.
Unauthorized distribution or disclosure of its contents is a violation of that contract or agreement and persons doing so may be liable for penalties as provided by law.

Warranties and Liabilities

All warranties given by Alias Limited about equipment or software are set forth in the EULA provided with the software or applicable license for the software product signed by Alias Limited, and
nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such warranties. Alias Limited believes the information in this
publication is accurate as of its publication date.
The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Alias Limited is not responsible for any
error that may appear in this document.
The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license. No responsibility is assumed by Alias Limited for the
use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE
USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.
Alias Limited is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users should verify for themselves that the data is accurate and
suitable for their project work.

Trademarks
ISOGEN and SPOOLGEN are registered trademarks of Alias Limited. All other brands and product names are trademarks of their respective owners.
Contents
Preface ......................................................................................................................................................... 7

What's New in ISOGEN Symbol Keys ....................................................................................................... 9

Introduction ............................................................................................................................................... 10
Flanges and Balled Joints .................................................................................................................... 12
LSJE-Type Flanges .............................................................................................................................. 15
Hygienic Fittings ................................................................................................................................... 16
Miscellaneous Pipe Components ......................................................................................................... 23
Miscellaneous Items ............................................................................................................................. 26
Penetration Plate Items ........................................................................................................................ 28
Nozzles ................................................................................................................................................. 29
Inline Filters .......................................................................................................................................... 30
Instruments ........................................................................................................................................... 31
Pipe Blocks ........................................................................................................................................... 36
Vents..................................................................................................................................................... 37
Traps..................................................................................................................................................... 38
Welds .................................................................................................................................................... 39
Symbol Coupling................................................................................................................................... 44
Elbows and Bends ................................................................................................................................ 46
Couplings .............................................................................................................................................. 58
Caps ..................................................................................................................................................... 61
Crosses................................................................................................................................................. 63
Fixed Length Pipes ............................................................................................................................... 65
Spindles ................................................................................................................................................ 67
Tees ...................................................................................................................................................... 70
Reducers .............................................................................................................................................. 76
Supports ............................................................................................................................................... 84
Unions................................................................................................................................................... 86
Olets ..................................................................................................................................................... 87
Valves ................................................................................................................................................... 90

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 5

Contents

Three-Way Valves.......................................................................................................................... 93
Valves - 4-Way............................................................................................................................... 94
Clamped Joints ..................................................................................................................................... 95
Liners (Connectors) .............................................................................................................................. 96

6 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Preface
This document is intended to comprehensively cover all current ISOGEN symbol key symbol shapes.
Alias Limited gives you permission to print as many copies of this document as you need for non-commercial use at your company. You cannot
reprint this document for resale or redistribution outside your company.

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 7

What's New in ISOGEN Symbol Keys
The following changes have been made to the ISOGEN Symbol Keys Reference Guide.
Version 2014 Service Pack 1 (12.0.1)
 No changes have been made to this document in Version 2014 Service Pack 1.
Version 2014 (12.0)
 No changes have been made to this document in Version 2014.

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 9

Introduction

SECTION 1

Introduction
All components generated by ISOGEN are defined by a unique code called a symbol key (SKEY). SKEYs contain 2-4 characters; the first two
characters define the type of component, and the last two characters define the end type, such as flanged, butt welded, or screwed. You can
specify an appropriate end condition by replacing the ** characters in the SKEY with one of the sets of characters from the table below.
SKEY Characters End Condition

BW Butt Weld
CP Compression
SW Socket Weld
FL Flanged
SC Screwed
PL Plain End
LN Liner Nut
LC Liner / Clamp
LR Reducing Liner / Nut
MP Male Part
PF Push Fit
GL Glued
CL Clamped

10 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

SKEY Characters End Condition

FA Flared
BS / SB Ball and Socket (used on fixed length type pipe work)
GF Gland (used on fixed length type pipe work)

 To denote the number of segments, replace the AT symbol (@) in the SKEY with an integer value in the range 1 to 9, inclusive. Currently,
regardless of the value assigned to the AT sign, the software draws the symbol according to the SKEY plotted isometric shape.
 To denote the bend radius, replace the PLUS symbol (+) in the SKEY with an integer value in the range 1 to 9, inclusive.

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 11

 Flanges and Balled Joints

Flanges and Balled Joints

Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record
Blind flange (also known as a Blank
flange. Symbol includes tapping FLBL Yes FLANGE-BLIND 107
connection)

Flared/Loose backing flange FLFL Yes FLANGE 105

Loose backing flange FLLB Yes FLANGE 105

FLANGE-
Reducing concentric flange FLRC Yes REDUCING- 65/0
CONCENTRIC
FLANGE-
Reducing eccentric flange FLRE Yes REDUCING- 65/0
ECCENTRIC

Screwed flange FLSC Yes FLANGE 105

Slip-on flange with J-type weld FLSJ Yes FLANGE 105

Slip-on flange FLSO Yes FLANGE 105

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 12

Flanges and Balled Joints Flanges and Balled Joints

Plotted User- PCF IDF

Description SKEY Shape
Isometric Shape Definable Identification Record

Orifice slip-on flange with

FOSO Yes FLANGE 105
tapping connection

Socket weld flange FLSW Yes FLANGE 105

Weld neck flange FLWN Yes FLANGE 105

Orifice weld neck flange with

FOWN Yes FLANGE 105
tapping connections

Lap joint ring/Stub end combined flange FBSE Yes FLANGE 105

Cast/lined fixed flange (Female) –

FLFF Yes FLANGE 105
Cast/lined flange

Cast/lined rotating flange FLFR Yes FLANGE 105

Cast/lined flange with

FLGF Yes FLANGE 105
Female gland type

Cast/ lined flange with

Male gland type FLGM Yes FLANGE 105

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 13

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Glued (Female) connection FLGL Yes FLANGE 105

Push fit (Female) connection FLPF Yes FLANGE 105

Seal-welded flange (Sarlun/Sargol)

FLSF Yes FLANGE 105
(Female) connection

Seal-welded flange (Sarlun/Sargol)

FLSM Yes FLANGE 105
(Male) connection

Concentric reducing flange FC** Yes FLANGE 105

Eccentric reducing flange FE** Yes FLANGE 105

Jacket weld neck flange JFWN Yes FLANGE 105

Jacket slip-on flange JFSO Yes FLANGE 105

14 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Hygienic Fittings LSJE-Type Flanges

LSJE-Type Flanges
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Lap joint ring

FLRG Yes LAPJOINT-RING 106
(Loose backing flange)

Lap joint stub end LAPJOINT-STUB-

FLSE Yes 106
(Loose backing flange) END

Stub end (LJSE) LAPJOINT-STUB-

FLMP Yes 106
(Use with glued//push fit systems) END

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 15

Hygienic Fittings
Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Male part connector

MPBW Yes No / No CONNECTOR 111
(Butt weld)

Male part connector

MPEX Yes No / No CONNECTOR 111
(Expanded)

Clamp liner (Butt weld) LCBW Yes No / No CONNECTOR 111

Clamp liner (Expanded) LCEX Yes No / No CONNECTOR 111

Backing nut liner butt welded LNBW Yes No / No CONNECTOR 111

Backing nut liner LN Yes No / No CONNECTOR 111

Backing nut reducing liner

LRBW Yes No / No CONNECTOR 111
(Butt weld)

16 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Hygienic Fittings Hygienic Fittings

Plotted User- Flow Arrow / PCF IDF

Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Backing nut reducing liner

LREX Yes No / No CONNECTOR 111
(Expanded)

Backing nut BNUT Yes No / No NUT 112

Clamp CLMP Yes No / No CLAMP 113

Drain/Vent plug DVP Yes No / No MISC-HYGENIC 114

Male blanking plug BM Yes No / No MISC-HYGENIC 114

Blank plain BP Yes No / No MISC-HYGENIC 114

Reducing concentric blank

BBC Yes No / No MISC-HYGENIC 114/0
boss

Reducing eccentric blank boss BBE Yes No / No MISC-HYGENIC 114/0

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 17

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Blank thermocouple connector BTP Yes No / -- MISC-HYGENIC 114/0

Male-to-male adapter ADMM Yes No / -- MISC-HYGENIC 114

Male-to-female adapter ADMF Yes No / -- MISC-HYGENIC 114

2 port single level

2Z** Yes No / -- VALVE-ANGLE 75/76
(angle type) valve (Z)

2 port single level

2D** Yes No / -- VALVE-ANGLE 75/76
(angle type) valve (D)

3 port single level valve (Z) 3Z** Yes No / -- VALVE-3WAY 80/0/81/82

18 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

3 port single level valve (D) 3D** Yes No / No VALVE-3WAY 80/0/81/82

85/0/86/87/
4 port single level valve (Z) 4Z** Yes No / No VALVE-4WAY
88

85/0/
4 port single level valve (D) 4D** Yes No / No VALVE-4WAY 86/87/
88

75/76/80/0/
Multi-port dual level valve with VALVE- 81/82
MD** Yes No / No
D spindle MULTIWAY 85/0/86/87/
88

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 19

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

75/76
80/0/
Multi-port dual level valve with VALVE- 81/82
MZ** Yes No / No
Z spindle MULTIWAY 85/0/
86/87/
88

Separator for multi-level valve DUMY Yes No / No N/A N/A

Graduated control valve (D) IG** Yes Yes / No INSTRUMENT 90/93

Non-return valve NV** Yes No / Yes VALVE 130

80/0/
3-way check valve K3** Yes No / No VALVE-3WAY
81/82

20 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Wide-angle cock KV** Yes Yes / No VALVE 130

Pressure relief valve (Z) VZ** Yes No / Yes VALVE 130

Butterfly valve ZB** Yes Yes / No VALVE 130

Graduated control valve (Z) ZG** Yes Yes / No VALVE 130

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 21

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Pressure relief valve

ZV** Yes No / Yes INSTRUMENT 90/93
(Instrument type) (I)

22 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Miscellaneous Pipe Components Miscellaneous Pipe Components

Miscellaneous Pipe Components

Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

MISC-
Block angle BA** Yes No / No COMPONENT- 95/96
ANGLE

MISC-
Expansion bellows EX** Yes Yes / No COMPONENT 95/96

MISC-
Flame trap FT** Yes Yes / No 95/96
COMPONENT

MISC-
Flexible hose FX** Yes Yes / No 95/96
COMPONENT

MISC-
Hose coupling CH** Yes No / No 95/96
COMPONENT

MISC-
Non-category item NC** Yes No / No 95/96
COMPONENT

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 23

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

MISC-
Block offset BO** Yes Yes / No COMPONENT- 95/96
OFFSET

MISC-
Block return BR** Yes Yes / No COMPONENT- 95/96
RETURN

MISC-
Plug PL Yes No / No 95/96
COMPONENT

MISC-
Restrictor plate RP Yes Yes / No
COMPONENT 95/96

REINFORCEMENT
Reinforcing pad RPAD Yes No / No PAD NONE

MISC-
Sight glass SG** Yes Yes / No
COMPONENT 95/96

24 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

MISC-
Slip plate SP Yes No / No
COMPONENT 95/96

MISC-
Slip ring SR Yes No / No
COMPONENT 95/96

MISC-
Spectacle blind (closed) SB Yes No / No 95/96
COMPONENT

MISC-
Spectacle blind (open) OB Yes No / No 95/96
COMPONENT

MISC-
Tundish (funnel) TU** Yes Yes / Yes COMPONENT 95/96

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 25

Miscellaneous Items Miscellaneous Items

Miscellaneous Items
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

INSULATION-
Insulation symbol INPP Yes 149
SYMBOL

Floor symbol FLOR Yes FLOOR-SYMBOL 149

Flow arrow FLOW Yes FLOW-ARROW 149

No 149
Location point LOPT LOCATION-POINT

Wall symbol WALL Yes WALL-SYMBOL 149

Arrow head (dimension line) AR01 Yes N/A N/A

Arrow head (message line) AR02 Yes N/A N/A

26 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Line break AR04 Yes N/A N/A

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 27

Penetration Plate Items Nozzles

Penetration Plate Items

Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Used with Used with

Penetration plate (End sections) PLT1 Yes PENETRATION- symbol key
PLATE CRPP

Used with Used with

Penetration plate (Center sections) PLT2 Yes PENETRATION- symbol key
PLATE CRPP

MISC-
Locating pin LPIN Yes 95/96
COMPONENT

28 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Nozzles
Plotted User- PCF
Description SKEY Shape IDF Record
Isometric Shape Definable Identification

Nozzle (Start flanged) NZFS Yes NOZZLE -31

Nozzle (End flanged) NZFE Yes NOZZLE -31

Nozzle (Start welded) Yes NOZZLE -31

NZWS

Nozzle (End welded) NZWE Yes NOZZLE -31

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 29

Inline Filters Instruments

Inline Filters
Plotted
User- Flow Arrow / PCF IDF
Description SKEY Shape Isometric
Definable Flow Dependency Identification Record
Shape

Straight through filter/strainer FI** Yes Yes / Yes FILTER 136/137

Angle filter/strainer FA** Yes No / No FILTER-ANGLE 136/137

Offset filter/strainer FO** Yes Yes / No FILTER-OFFSET 136/137

Return filter/strainer FR** Yes Yes / No FILTER-RETURN 136/137

30 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Instruments
Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Instrument II** Yes No / No INSTRUMENT 90/93

INSTRUMENT-
Instrument angle IA** Yes No / No ANGLE 90/93

INSTRUMENT-
Instrument offset IO** Yes Yes / No 90/93
OFFSET

INSTRUMENT-
Instrument return IR** Yes Yes / No 90/93
RETURN

INSTRUMENT-
Instrument dial IDPL N/A No No / No 90
DIAL

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 31

Instruments Instruments

Plotted User- Flow Arrow / PCF IDF

Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

INSTRUMENT-
Instrument dial (flanged) IDFL N/A No No / No 90
DIAL

Orifice plate OP Yes Yes / No INSTRUMENT 90/93

Restrictor plate PR Yes Yes/No INSTRUMENT 90/93

Rupture disk DR Yes Yes / Yes INSTRUMENT 90/93

Control valve CV** Yes Yes / No INSTRUMENT 90/93

INSTRUMENT-
3-way control valve C3** Yes No / No 90/0/91/93
3WAY

32 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

INSTRUMENT- 90/0/
4-way control valve C4** Yes No / No
4WAY 91/92/93

INSTRUMENT-
Angled control valve CA** Yes No / No 90/93
ANGLE

Hand-operated control valve HV** Yes Yes / No INSTRUMENT 90/93

Hand-operated 3-way INSTRUMENT- 90/0/

H3** Yes No / No
control valve 3WAY 91/93

Hand-operated 4-way INSTRUMENT- 90/0/91/

control valve H4** Yes No / No
4WAY 92/93

Hand-operated angled INSTRUMENT-

HA** Yes No / No 90/93
control valve ANGLE

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 33

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Motor-operated control valve MV** Yes Yes / No INSTRUMENT 90/93

Motor-operated 3-way INSTRUMENT- 90/0/

control valve M3** Yes No / No
3WAY 91/93

Motor-operated 4-way INSTRUMENT- 90/0/91/

M4** Yes No / No
control valve 4WAY 92/93

Motor-operated angled INSTRUMENT-

MA** Yes No / No 90/93
control valve ANGLE

Instrument angle control valve INSTRUMENT-

SA** Yes No / No 90/93
with square indicator ANGLE

Square indicator control valve SV** Yes Yes / No INSTRUMENT 90/93

34 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Square indicator 3-way INSTRUMENT- 90/0/

S3** Yes No / No
control valve 3WAY 91/93

Square indicator 4-way INSTRUMENT- 90/0/

S4** Yes No / No
control valve 4WAY 91/92/93

Angled pressure INSTRUMENT-

XA** Yes Yes / No 90/93
reducing angle ANGLE

Pressure reducing INSTRUMENT-

XV** Yes Yes / Yes 90/93
instrument valve ANGLE

Angled relief/valve INSTRUMENT-

instrument valve RA** Yes Yes / No ANGLE 90/93

Relief/Vent instrument valve RV** Yes Yes / No INSTRUMENT 90/93

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 35

Pipe Blocks Vents

Pipe Blocks
Plotted User PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Fixed length pipe block PF Yes PIPE-BLOCK-FIXED 102

PIPE-BLOCK-
Variable length pipe block PV Yes 103
VARIABLE

36 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Vents
Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Rupture disk RD Yes Yes / Yes SAFETY-DISC 134

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 37

Traps Welds

Traps
Plotted User- Flow Arrow/ PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Angle trap TA** Yes No / No TRAP-ANGLE 132/133

Offset trap TO** Yes Yes / No 132/133

TRAP-OFFSET

Return trap TR** Yes Yes / No TRAP-RETURN 132/133

Inline trap TI** Yes No / No TRAP 132/133

38 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Welds
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Workshop weld WW Yes WELD 120

Dotted workshop weld WWD Yes WELD 120

Site weld WS Yes WELD 120

Tack for site weld WST Yes WELD 120

Dotted site weld WSD Yes WELD 120

Field fit weld WF Yes WELD 120

Tack for field fit weld WFT Yes WELD 120

Dotted field fit weld WFD Yes WELD 120

Offshore weld WO Yes WELD 120

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 39

Welds Welds

Plotted User- PCF IDF

Description SKEY Shape
Isometric Shape Definable Identification Record

Tack for offshore weld WOT Yes WELD 120

Dotted offshore weld WOD Yes WELD 120

Offshore field fit weld WOF Yes WELD 120

Tack for offshore field fit weld WOFT Yes WELD 120

Special site weld

WSSP Yes WELD 120
(non-spooling)

Automatic workshop weld WWA Yes WELD 120

Field fit weld with shop test

WFST Yes WELD 120
requirement

Field fit offshore dotted WOFD Yes WELD 120

Mitre weld WM N/A No WELD 120

Mitre field fit weld WMF N/A No WELD 120

40 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Mitre tack weld WMT N/A No WELD 120

Mitre field fit tack weld WMFT N/A No WELD 120

Site workshop test weld WSST No WELD 120

Workshop shot test weld WWST No WELD 120

Offshore shop test weld WOST No WELD 120

Offshore field fit shop test weld WVST No WELD 120

Support weld ZSP* No WELD 120

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 41

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Trunnion weld ZTN* No WELD 120

Reinforced trunnion ZTR* No WELD 120

Site socket/screwed
XX N/A No WELD 120
compression weld

Site socket/screwed
XXD N/A No WELD 120
compression dotted weld

Erection seal weld WSSR Yes WELD 120

42 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Symbol Coupling

Plotted User- PCF IDF

Description SKEY Shape
Isometric Shape Definable Identification Record

Offshore seal weld WOSR Yes WELD 120

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 43

Symbol Coupling
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Coupling with glued

COGL Yes COUPLING 126
connections

Coupling with push fit end

COPF Yes COUPLING 126
connections

Coupling with flared end

COFA Yes COUPLING 126
connections

Coupling with clamped end

COCL Yes COUPLING 126
connections

Coupling with Victaulic

COVT Yes COUPLING 126
connections (Grooved pipe)

Coupling with Victaulic

connections (Welded COVR Yes COUPLING 126
connections)

44 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Elbows and Bends Symbol Coupling

Plotted User- PCF IDF

Description SKEY Shape
Isometric Shape Definable Identification Record

Coupling with compression

CSCP Yes COUPLING 126
sleeve connections

Coupling with Grayloc

COGY Yes COUPLING 126
connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 45

Elbows and Bends
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Butt weld elbow

ELBW N/A No ELBOW 35/36
(90° and 45°)

Compression elbow
ELCP N/A No ELBOW 35/36
(90° and 45°)

Screwed elbow
with Female ends ELSC N/A No ELBOW 35/36
(90° and 45°)

Socket weld elbow

ELSW N/A No ELBOW 35/36
(90° and 45°)

Screwed elbow
with Male ends EBSC N/A No ELBOW 35/36
(90° and 45°)

46 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Elbows and Bends Elbows and Bends

Plotted User- PCF IDF

Description SKEY Shape
Isometric Shape Definable Identification Record

Socket weld teed elbow

ETSW N/A No ELBOW-TEED 70/0/71/72
(90° and 45°)

Screwed teed elbow

ETSC N/A No ELBOW-TEED 70/0/71/72
(90° and 45°)

Compression teed elbow

ETCP N/A NO ELBOW-TEED 70/0/71/72
(90° and 45°)

Butt weld teed elbow

ETBW N/A No ELBOW-TEED 70/0/71/72
(90° and 45°)

Reducing elbow ER** N/A No ELBOW-REDUCING 35/36

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 47

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Butt weld return elbow (180°) EUBW N/A No ELBOW 35/36

Plain end return elbow (180°) EUPL N/A No ELBOW 35/36

Flanged teed elbow

(All angles) BTFL N/A No BEND-TEED 70/0/71/72

Butt weld mitre tee bend MTBW N/A No BEND-TEED 70/0/71/72

Butt weld mitre bend MIBW N/A No BEND 30/31

Flanged mitre bend MIFL N/A No BEND 30/31

48 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Mitre tee bend with plain ends MTPL N/A No BEND-TEED 70/0/71/72

Flanged mitre tee bend MTFL N/A No BEND-TEED 70/0/71/72

Flanged bend
BEFL N/A No BEND 30/31
(All angles)

Bend (Multi-axis lined pipes.

Must be used in conjunction BM** N/A No BEND 30/31
with PIPELINE-TYPE.)

Flanged 180° return bend BUFL N/A No BEND 30/31

Butt weld lobster bend L@BW N/A No BEND 30/31

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 49

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Butt weld lobster tee bend T@BW N/A No BEND-TEED 70/0/71/72

Flanged lobster bend L@FL N/A No BEND 30/31

Flanged lobster tee bend T@FL N/A No BEND-TEED 70/0/71/72

Pulled bend (All angles) PB+D N/A No BEND 30/31

180° pulled return bend BU+D N/A No BEND 30/31

Pulled tee bend (All angles) TB+D N/A No BEND-TEED 70/0/71/72

50 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Pulled bend with weld

PBBW N/A No BEND 30/31
at each end

180° Pulled return bend

BUBW N/A No BEND 30/31
with weld at each end

Pulled tee bend with weld

TBBW N/A No BEND-TEED 70/0/71/72
at each end

Bend with flared end

BEFA N/A Ends only BEND 30/31
connection

Bend with clamped end

BECL N/A Ends only BEND 30/31
connections

Elbow with flared end

ELFA N/A Ends only ELBOW 35/36
connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 51

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Elbow with clamped end

connections ELCL N/A Ends only ELBOW 35/36

Teed elbow with flared end

ETFA N/A Ends only ELBOW-TEED 70/71/72
connections

Teed elbow with clamped end

ETCL N/A Ends only ELBOW-TEED 70/71/72
connections

Reducing elbow with flared end ELBOW-

ERFA N/A Ends only 35/36
connections REDUCING

Reducing elbow ELBOW-

ERCL N/A Ends only 35/36
with clamped end connections REDUCING

The ends on the following elbow and bend components can be individually designated MALE or FEMALE.

Elbow with flanged gland-type

ELGF N/A Ends only ELBOW 35/36
end connections

Elbow with flanged ball/socket

ELBS N/A Ends only ELBOW 35/36
end connections

52 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Teed elbow with

ETGL N/A Ends only ELBOW-TEED 70/71/72
glued end connections

Teed elbow with

ETPF N/A Ends only EBOW-TEED 70/71/72
push fit end connections

Bend with flanged ball/socket

BEBS N/A Ends only BEND 30/31
end connections

Tee bend with flanged

ball/socket end connections BTBS N/A Ends only BEND-TEED 70/0/71/72

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 53

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Bend with flanged gland-type

BEGF N/A Ends only BEND 30/31
end connections

Tee bend with flanged

TBGF N/A Ends only BEND-TEED 70/0/71/72
gland-type end connections

Bend with glued end

BEGL N/A No BEND 30/31
connections

Elbow with glued end

ELGL N/A Ends only ELBOW 35/36
connections

54 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Elbow with push fit end

ELPF N/A Ends only ELBOW 35/36
connections

Bend with push fit connections BEPF N/A No BEND 30/31

Teed elbow
ETGL N/A Ends only ELBOW-TEED 70/71/72
with glued end connections

Teed elbow
ETPF N/A Ends only EBOW-TEED 70/71/72
with push fit end connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 55

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Bend with flanged ball/socket

end connections BEBS N/A Ends only BEND 30/31

Tee bend with flanged

BTBS N/A Ends only BEND-TEED 70/0/71/72
ball/socket end connections

Bend with flanged gland-type

BEGF N/A Ends only BEND 30/31
end connections

Tee bend with flanged

TBGF N/A Ends only BEND-TEED 70/0/71/72
gland-type end connections

56 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Bend with glued end

BEGL N/A No BEND 30/31
connections

Elbow with glued end

ELGL N/A Ends only ELBOW 35/36
connections

Elbow with push fit end

ELPF N/A Ends only ELBOW 35/36
connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 57

Couplings Couplings

Couplings
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Nipple (Running screwed) NRSC Yes COUPLING 126

Nipple (Barrel screwed) NBSC Yes COUPLING 126

Coupling (Compression) COCP Yes COUPLING 126

Coupling (Screwed) COSC Yes COUPLING 126

Coupling (Screwed) COSW Yes COUPLING 126

Elbolet coupling (Butt weld) CEBW Yes ELBOLET 126/0

Elbolet coupling (Screwed) CESC Yes ELBOLET 126/0

Elbolet coupling (Socket weld) CESW Yes ELBOLET 126/0

58 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Coupling with glued

COGL Yes COUPLING 126
end connections

Coupling with push fit

COPF Yes COUPLING 126
end connections

Coupling with flared

COFA Yes COUPLING 126
end connections

Coupling with clamped

COCL Yes COUPLING 126
end connections

Coupling with Victaulic

connections (Grooved pipe) COVT Yes COUPLING 126

Coupling with Victaulic

connections (Welded
connections) COVR Yes COUPLING 126

Coupling with compression

CSCP Yes COUPLING 126
sleeve connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 59

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Coupling with Grayloc

COGY Yes COUPLING 126
connections

60 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Caps Caps

Caps
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Butt weld cap (includes

KABW Yes CAP 125/0
tapping connections)

Compression cap KACP Yes CAP 125/0

Screwed cap KASC Yes CAP 125/0

Socket Weld cap KASW Yes CAP 125/0

Flanged cap KAFL Yes CAP 125/0

Glued cap KAGL Yes CAP 125/0

Push fit cap KAPF Yes CAP 125/0

Flared cap KAFA N/A Yes CAP 125/0

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 61

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Clamped cap KACL N/A Yes CAP 125/0

62 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Crosses Crosses

Crosses
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

50/0/51/
Cross CR** N/A No CROSS
52/53

Uses YSML, 50/0/51/

Y-type cross CY** Yes CROSS
YMED, & YLRG 52/53

CROSS-SET-ON or 50/0/51/
Set-on cross CRSO N/A No
CROSS-STUB 52/53

CROSS-SET-ON or 50/0/51/
Set-on reinforced cross CRRF N/A No
CROSS-STUB 52/53

CROSS-SET-ON or 50/0/51/
Stub in cross CSSO N/A No
CROSS-STUB 52/53

CROSS-SET-ON or 50/0/51/
Stub in reinforced cross CSRF N/A No
CROSS-STUB 52/53

Uses YSML, CROSS-SET-ON or 50/0/51/

Set-on cross (Y-type) CYSO Yes
YMED, & YLRG CROSS-STUB 52/53

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 63

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Cross with flared 50/0/51/

CRFA N/A Ends only CROSS
end connections 52/53

Cross with clamped 50/0/51/

CRCL N/A Ends only CROSS
end connections 52/53

The ends on the following cross components can be individually designated as MALE or FEMALE.

Cross with glued 50/0/51/

CRGL N/A Ends only CROSS
end connections 52/53

Cross with push fit 50/0/51/

CRPF N/A Ends only CROSS
end connections 52/53

Cross with flanged ball/socket 50/0/51/

CRBS N/A Ends only CROSS
end connections 52/53

Cross with flanged gland-type 50/0/51

CRGF Ends only CROSS
end connections /52/53

64 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Fixed Length Pipes Fixed Length Pipes

Fixed Length Pipes

Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Fixed length pipe with

FPFL No PIPE-FIXED 101
integral ends

Fixed length pipe without

FPPL Yes PIPE-FIXED 101
flanged ends

Fixed pipe with flared

FPFA Yes PIPE-FIXED 101
end connections

Fixed pipe with clamped

FPCL Yes PIPE-FIXED 101
end conditions

The ends on the following fixed length pipe components can be individually designated MALE or FEMALE.

Fixed pipe with glued

FPGL Yes PIPE-FIXED 101
end connections

Fixed pipe with push fit

FPPF Yes PIPE-FIXED 101
end connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 65

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Fixed pipe with screwed

FPSC Yes PIPE-FIXED 101
end connections

Fixed pipe with socket

FPSW Yes PIPE-FIXED 101
end connections

Fixed pipe with compression

FPCP Yes PIPE-FIXED 101
end connections

Fixed pipe with flanged

ball and socket FPFL Yes PIPE-FIXED 101

66 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Spindles Spindles

Spindles
User-
Description SKEY Shape PCF Identification IDF Record
Definable

Spindle 1 01SP Yes SPINDLE-SKEY 126

Spindle 2 02SP Yes SPINDLE-SKEY 126

Spindle 3 03SP Yes SPINDLE-SKEY 126

Spindle 4 04SP Yes SPINDLE-SKEY 126

Spindle 5 05SP Yes SPINDLE-SKEY 126

Spindle 6 06SP Yes SPINDLE-SKEY 126

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 67

 User-
Description SKEY Shape PCF Identification IDF Record
Definable

Spindle 7 07SP Yes SPINDLE-SKEY 126

Spindle 8 08SP Yes SPINDLE-SKEY 126

Spindle 9 09SP Yes SPINDLE-SKEY 126

Spindle 10 10SP Yes SPINDLE-SKEY 126

Spindle 11 11SP Yes SPINDLE-SKEY 126

Spindle 12 12SP Yes SPINDLE-SKEY 126

68 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 User-
Description SKEY Shape PCF Identification IDF Record
Definable

Spindle 13 13SP Yes SPINDLE-SKEY 126

Spindle 14 14SP Yes SPINDLE-SKEY 126

Spindle 15 15SP Yes SPINDLE-SKEY 126

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 69

Tees Tees

Tees
Plotted User- PCF
Description SKEY Shape IDF Record
Isometric Shape Definable Identification

Tee TE** No TEE 45/0/46/47

TEE-SET-ON or
Set-on tee TESO No 45/0/46/47
TEE-STUB

TEE-SET-ON or
Set-on reinforced tee TERF No 45/0/46/47
TEE-STUB

TEE-SET-ON or
Stub in tee TSSO No 45/0/4/47
TEE-STUB

TEE-SET-ON or
Stub in reinforced tee TSRF No 45/0/46/47
TEE-STUB

Socket weld tee TESW No TEE 45/0/46/47

70 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Swept branch tee (Butt weld) TSBW No TEE 45/0/46/47

Swept branch tee (Flanged) TSFL No TEE 45/0/46/47

Swept socket weld tee TSSW No TEE 45/0/46/47

Swept compression tee TSCP No TEE 45/0/46/47

Ghost tee TEGG No TEE 45/0/46/47

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 71

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Pulled out tee TPUL No TEE 45/0/46/47

Offset tee (reinforced set-on)

TORF No TEE 45/0/46/47

Set-on tangential tee

TOSO No TEE 45/0/46/47

Tangential tee (reinforced

set-on) TTRF No TEE 45/0/46/47

Offset tee (set-on)

TTSO No TEE 45/0/46/47

72 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Instrument tee IT** No INSTRUMENT-TEE 40/41/42/0

Tee with flared

TEFA Yes TEE 45/0/46/47
end connections

Tee with clamped

TECL Yes TEE 45/0/46/47
end connections

The ends on the following tee components can be individually designated as MALE or FEMALE.

Tee with glued

TEGL Yes TEE 45/0/46/47
end connections

Tee with push fit

TEPF Yes TEE 45/0/46/47
end connections

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 73

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Tee with flanged ball/socket

TEBS Yes TEE 45/0/46/47
end connections

Tee with flanged gland-type

TEGF Yes TEE 45/0/46/47
end connections

SKEYs YLRG, YMED, and YSML are used with Y-Type Tees / Crosses.

Y-type tee (Large) YLRG See Y-type tee/cross Yes See Y-type tee/cross

See 'Y' Type Yes

Y-type tee (Medium) YMED See Y-type tee/cross
Tee/Cross

Y-type tee (Small) YSML See Y-type tee/cross Yes See Y-type tee/cross

Uses YSML,
Y-type tee TY** Yes TEE 45/0/46/47
YMED or YLRG

74 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Reducers

Plotted User- IDF

Description SKEY Shape PCF Identification
Isometric Shape Definable Record

Uses YSML, YMED or TEE-SET-ON or

Set-on Y-type tee TYSO Yes 45/0/46/47
YLRG TEE-STUB

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 75

Reducers
Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

REDUCER-
Concentric reducer RC** Yes No / No 55/0
CONCENTRIC

REDUCER-
Concentric reducer
CTBW Yes No / No CONCENTRIC- 60/0/61/62
(Butt weld with a connection)
TEED

Concentric reducer REDUCER-

(Socket weld with a CTSW Yes No / No CONCENTRIC- 60/0/61/62
connection) TEED

Concentric reducer (Butt weld REDUCER-

CPBW Yes No / No 55/0
fabricated from plate) CONCENTRIC

Concentric reducer (Butt weld REDUCER-

CSBW Yes No / No 55/0
swaged from pipe) CONCENTRIC

Concentric reducer REDUCER-

(Fabricated from a plate with CZBW Yes No / No CONCENTRIC- 60/0/61/62
a connection) TEED

76 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Reducers Reducers

Plotted User- Flow Arrow / PCF IDF

Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Concentric reducer REDUCER-

(Fabricated from plate - CZFL Yes No / No CONCENTRIC- 60/0/61/62
flanged with a connection) TEED

REDUCER-
Concentric reducer (Swaged
CXBW Yes No / No CONCENTRIC- 60/0/61/62
from pipe with a connection)
TEED

Concentric reducer
REDUCER-
(Fabricated from plate - CPFL Yes No / No 55/0
CONCENTRIC
flanged)

Concentric reducer (Swaged REDUCER-

CSFL Yes No / No 55/0
from plate - flange) CONCENTRIC

REDUCER-
Concentric reducer (Flanged
CTFL Yes No / No CONCENTRIC- 60/0/61/62
with a connection)
TEED

Concentric reducer (Swaged REDUCER-

from pipe - flanged with a CXFL Yes No / No CONCENTRIC- 60/0/61/62
connection) TEED

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 77

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Concentric reducer (Screwed REDUCER-

RNSC Yes No / No 55/0
nipple) CONCENTRIC

REDUCER-
Concentric reducer (Screwed
CTSC Yes No / No CONCENTRIC- 60/0/61/62
with a connection)
TEED

Concentric reducer REDUCER-

RBSC Yes No / No 55/0
(Screwed bush) CONCENTRIC

Concentric reducer REDUCER-

RBSW Yes No / No 55/0
(Socket weld bush) CONCENTRIC

REDUCER-
Eccentric reducer RE** Yes No / No 55/0
ECCENTRIC

Eccentric reducer REDUCER-

EPBW Yes No / No ECCENTRIC 55/0
(Fabricated from plate)

Eccentric reducer REDUCER-

ESBW Yes No / No 55/0
(Swaged from pipe) ECCENTRIC

78 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

REDUCER-
Eccentric reducer
OTBW Yes No / No ECCENTRIC- 60/0/61/62
(Butt weld with a connection)
TEED

Eccentric reducer (Butt REDUCER-

weld fabricated from plate EZBW Yes No / No ECCENTRIC- 60/0/61/62
with a connection) TEED

Eccentric reducer - butt weld REDUCER-

(Swaged from pipe EXBW Yes No / No ECCENTRIC- 60/0/61/62
with connection) TEED

REDUCER-
Eccentric reducer
OTSC Yes No / No ECCENTRIC- 60/0/61/62
(Screwed with a connection)
TEED

Eccentric reducer REDUCER-

EPFL Yes No / No 55/0
(Fabricated from plate) ECCENTRIC

Eccentric reducer - flanged REDUCER-

ESFL Yes No/No 55/0
(Swaged from pipe) ECCENTRIC

REDUCER-
Eccentric reducer
OTFL Yes No / N o ECCENTRIC- 60/0/61/62
(Flanged with a connection)
TEED

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 79

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Eccentric reducer - flanged REDUCER-

(Fabricated from plate with EZFL Yes No / No ECCENTRIC- 60/0/61/62
a connection) TEED

Eccentric reducer - flanged REDUCER- 60/0/61/

(Swaged from pipe EXFL Yes No / No ECCENTRIC-
with a connection) TEED 62

REDUCER-
Reducing block RFPL Yes Yes / No 55/0
CONCENTRIC

Concentric reducer with REDUCER-

RCFA N/A Yes Yes / No 55/0
flared end connections CONCENTRIC

Concentric reducer with REDUCER-

RCCL N/A Yes Yes / No 55/0
clamped end connections CONCENTRIC

REDUCER-
Concentric teed reducer with
CTFA N/A Yes No / No CONCENTRIC- 60/0/61/62
flared end connections
TEED

80 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

REDUCER-
Concentric teed reducer with
CTCL N/A Yes No / No CONCENTRIC- 60/0/61/62
clamped end connections
TEED

Eccentric reducer with flared REDUCER-

REFA N/A Yes No / No 55/0
end connections ECCENTRIC

Eccentric reducer with REDUCER-

RECL N/A Yes No / No 55/0
clamped end connections ECCENTRIC

REDUCER-
Eccentric teed reducer with
OTFA N/A Yes No / No CONCENTRIC- 60/0/61/62
flared end connections
TEED

REDUCER-
Eccentric teed reducer with
OTCL N/A Yes No / No CONCENTRIC- 60/0/61/62
clamped end connections
TEED

The ends on the following cross components can be individually designated as MALE or FEMALE.

Eccentric reducer with REDUCER-

REGL N/A Yes No / No 55/0
glued end conditions ECCENTRIC

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 81

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Eccentric reducer with push REDUCER-

REPF N/A Yes No / No 55/0
fit end connections ECCENTRIC

REDUCER- 60/0/61/62
Eccentric teed reducer with
OTGL N/A Yes No / No CONCENTRIC-
glued end connections
TEED

REDUCER-
Eccentric teed reducer with
OTPF N/A Yes No / No CONCENTRIC- 60/0/61/62
push fit end connections
TEED

Concentric reducer with REDUCER-

RCGL N/A Yes Yes / No 55/0
glued end conditions CONCENTRIC

Concentric reducer with push REDUCER-

fit end connections RCPF N/A Yes Yes / No CONCENTRIC 55/0

82 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

REDUCER-
Concentric teed reducer with
CTGL N/A Yes No / No CONCENTRIC- 60/0/61/62
glued end connections
TEED

REDUCER-
Concentric teed reducer with
CTPF N/A Yes No / No CONCENTRIC- 60/0/61/62
push fit end connections
TEED

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 83

Supports Supports

Supports
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

01HG
Hanger/Support Yes SUPPORT 150
(or Blank)

Anchor ANCH Yes SUPPORT 150

Duck foot DUCK Yes SUPPORT 150

Support - Guide/Steady GUID Yes SUPPORT 150

Skid SKID Yes SUPPORT 150

84 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Spring SPRG Yes SUPPORT 150

Hanger HANG Yes SUPPORT 150

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 85

Unions Olets

Unions
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Union UN** Yes UNION 127/0

86 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Olets
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Olet (Half coupling screwed) HCSC Yes OLET 40/0/41/42

Olet (Half coupling socket weld) HCSW Yes OLET 40/0/41/42

Nipolet NI** Yes OLET 40/0/41/42

Nipolet (Screwed) NISC Yes OLET 40/0/41/42

Sockolet (Socket weld) SKSW Yes OLET 40/0/41/42

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 87

Olets Olets

Plotted User- PCF IDF

Description SKEY Shape
Isometric Shape Definable Identification Record

Sweepolet (Butt weld) SWBW Yes OLET 40/0/41/42

Thredolet (Screwed) THSC Yes OLET 40/0/41/42

Weldolet (Butt weld) WTBW Yes OLET 40/0/41/42

Latrolet (Screwed) LASC Yes OLET 40/0/41/42

Latrolet (Socket weld) LASW Yes OLET 40/0/41/42

88 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Latrolet (Butt weld) LABW Yes OLET 40/0/41/42

Flanged instrument tee ITFL No INSTRUMENT-TEE 40/0/41/42

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 89

Valves Valves

Valves
Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Angle valve AV** Yes Yes / No VALVE-ANGLE 75/76

Relief/Vent angle valve AR** Yes Yes / No VALVE-ANGLE 75/76

Pressure reducing angle valve AX** Yes Yes / No VALVE-ANGLE 75/76

Basic valve VV** Yes Yes / No VALVE 130/0

Check valve VC** Yes Yes / No VALVE 130/0

Check valve (alternative) CK** Yes No / Yes VALVE 130/0

Ball valve VB** Yes Yes / No VALVE 130/0

90 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Butterfly valve VY** Yes Yes / No VALVE 130/0

Diaphragm valve VD** Yes Yes / No VALVE 130/0

Globe valve VG** Yes Yes / No VALVE 130/0

Pressure reducing valve VX** Yes Yes / Yes VALVE 130/0

Cock valve VK** Yes Yes / No VALVE 130/0

Gate valve Yes Yes / No VALVE 130/0

VT**

Needle valve VN** Yes Yes / No VALVE 130/0

Plug valve VP** Yes Yes / No VALVE 130/0

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 91

 Plotted User- Flow Arrow / PCF IDF
Description SKEY Shape
Isometric Shape Definable Flow Dependency Identification Record

Relief/Vent valve VR** Yes Yes / No VALVE 130/0

Slide valve VS** Yes Yes / No VALVE 130/0

92 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Three-Way Valves
Plotted Isometric User- PCF IDF
Description SKEY Shape
Shape Definable Identification Record

80/0/81/
Three-way valve V3** Yes VALVE-3WAY
82/83

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 93

Valves - 4-Way
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Four-way valve V4** Yes VALVE-4WAY 80/0/81/82/83

94 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

Liners (Connectors) Clamped Joints

Clamped Joints
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record

Flared clamp CLMP Yes CLAMP 113

Victaulic (Grooved pipe end

CLVT Yes CLAMP 113
type)

Victaulic (Welded/forged ring

CLVR Yes CLAMP 113
type)

Compression sleeve coupling CLCS Yes CLAMP 113

Grayloc-type coupling CLGY Yes CLAMP 113

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 95

Liners (Connectors)
Plotted User- PCF IDF
Description SKEY Shape
Isometric Shape Definable Identification Record
Grayloc socket weld connector LNSW N/A N/A N/A N/A N/A
Grayloc (Female) screwed connector LNSC N/A N/A N/A N/A N/A
Victaulic - Welded ring type (Number
of welds set by Option Switch 77 LVBW N/A N/A N/A N/A N/A
Position 7)

96 ISOGEN Symbol Key (SKEY) Definitions Reference Guide

ISOGEN Symbol Key (SKEY) Definitions Reference Guide 97