Scribd
Upload
112 views

Troubleshooting Tips For Injection Blow Molding

The document provides troubleshooting tips for issues that may occur during the injection blow molding process. It discusses quality control procedures that can be implemented to monitor the process and identify needed adjustments. Specifications are required to clearly define quality standards and tolerances. Lubricant is often needed when molding with polyethylene resins to prevent sticking. A consistent troubleshooting plan and checklist is recommended to methodically address any problems like polymer sticking, short shots, neck folds, flashing, or incomplete threads.

Uploaded by

srisumi
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
112 views

Troubleshooting Tips For Injection Blow Molding

The document provides troubleshooting tips for issues that may occur during the injection blow molding process. It discusses quality control procedures that can be implemented to monitor the process and identify needed adjustments. Specifications are required to clearly define quality standards and tolerances. Lubricant is often needed when molding with polyethylene resins to prevent sticking. A consistent troubleshooting plan and checklist is recommended to methodically address any problems like polymer sticking, short shots, neck folds, flashing, or incomplete threads.

Uploaded by

srisumi
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Troubleshooting Tips for Injection Blow Molding

(Continued on Page 2)
INTRODUCTION
Injection blow molding incorporates particular characteristics and advantages over other
Processes. This process, which can produce a fully finished, close-tolerance container
Without scrap, is maximized when the correct polymer is selected and the production
Equipment is optimized. By utilizing the appropriate temperature profiles, pressures,
mold designs, associated tooling dimensions and trouble-shooting techniques, this process
can successfully yield the sought after results.
PRODUCING QUALITY BOTTLES
The utilization of quality control procedures can monitor the process and identify any
required adjustments. Here is a brief description of how these procedures can be
used.
􀂃 Implement a quality assurance system that analyzes and reports bottle quality
during the manufacturing process. This system identifies any trends and allows for
process corrections prior to potential quality problems.
􀂃 Develop and publish the quality standards for the desired bottle. Include dimensional
and visual requirements. Dimensional requirements may be in the neck area,
wall thickness, volume and/or bottle weight. Visual requirements may be the
color of the bottle, contamination, warpage, etc.
􀂃 Specifications are required for each quality standard. Specifications
communicate the determined quality requirements clearly. When generating
the specifications, consider the container's end use and any government regulations
that may exist. Once the specifications are determined, tolerances can be defined. A
tolerance is an acceptable deviation from the desired quality specification.
LUBRICANT
Producing injection blow molded containers using low density, linear low density and high
density polyethylene resin requires, in many cases, a lubricating agent to aid in processing.
Lubrication is required, in most cases, to prevent the polymer from sticking to the metal surfaces.
An insufficient amount of lubricant causes the parison to stick to the core rods or the parison
mold. Sticking causes processing problems such as unblown bottles or stringing as the molds
open.
As rule of thumb for polyethylene, a concentration of 0.2% calcium stearate or zinc
stearate is necessary to provide lubrication. This level may be adjusted to achieve the desired
result, which may be higher, or lower according the size of the container and/or the design of the
core rods. It is important to blend the lubricant sufficiently to achieve the consistency required
to produce quality bottles continually.
TROUBLESHOOTING TECHNIQUE
Develop a simple, consistent plan when troubleshooting. For example, record molding
conditions on a routine basis for reference, make only one change at a time, allow sufficient time
following each change for the effect of the change to become apparent, record changes inlog book, etc. The key is to have
a checklist for review when troubleshooting. Attached is a
proposed checklist that may not be all-inclusive, but provides a good starting point.
Page 2 of 3

tech.topic
Blow
Molding
Technical
(continued)
(Continued on Page 3)
PROBLEM SOLVING
Polymer sticking to core rods
􀂃 Melt temperature is too hot
􀂃 Parison mold temperature is too hot
􀂃 High or low packing or holding pressures
􀂃 Hot core rods
􀂃 Hot core rod tip
􀂃 Low lubricant level in resin
Polymer sticking to parison mold
􀂃 Melt temperature is too hot
􀂃 Parison mold temperature is too hot
􀂃 Packing or holding pressure is too low
􀂃 Packing or holding time is too short
􀂃 Low lubricant level in resin
Short Shots
􀂃 Loss of heat in the parison mold
􀂃 Loss of heat in the extruder or manifold
􀂃 Loss of injection pressure
􀂃 Loss of holding pressure
􀂃 Loss of screw RPM
􀂃 Foreign material is blocking the nozzle
orifice.
􀂃 Nozzle is frozen off due to low
temperature in base
􀂃 Manifold is too cold
􀂃 Nozzle orifice is too small
􀂃 Not enough preform time
􀂃 Hopper is empty
Neck folds and shoulder cuts
􀂃 Neck zone temperature is too cold
􀂃 Melt temperature is too cold
􀂃 Core-rod temperature is too cold
􀂃 Injection pressure is too high
􀂃 Holding pressure is too high
􀂃 Holding time is too long
􀂃 Cure time is too long
Parison Flashing
􀂃 Melt temperature is too hot
􀂃 Parison mold temperature is too hot
􀂃 High injection pressure
􀂃 High holding pressure
􀂃 Low clamping pressure
􀂃 Nozzle is damaged or not seated correctly
􀂃 Mold construction is poor
􀂃 Long, high-pressure, preform time
􀂃 Mold coolant lines are plugged
Pigtails
􀂃 Reverse RPM is too high
􀂃 Decompress time is too long.
Incomplete Threads
􀂃 Neck zone is too cold
􀂃 Melt is too cold
􀂃 Injection pressure is too low
􀂃 Holding pressure is too low
􀂃 Holding time is too short
􀂃 Poor venting in parison mold
􀂃 Insufficient blow pressure

You might also like