Scribd
Upload
85 views6 pages

Sensepoint XCD: Calibration Guide

This document provides instructions for calibrating the Sensepoint XCD gas detector. It can be calibrated through either a response check or full calibration. The full calibration involves zeroing the detector using zero gas and then spanning it using calibration gas at concentrations between 25-75% of the sensor's range. Detailed steps are provided for accessing the calibration menu and completing the zero and span processes. Special instructions are given for hydrogen sulfide sensors, which can be affected by humidity changes.

Uploaded by

OMAR YESID MARTINEZ PENA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
85 views6 pages

Sensepoint XCD: Calibration Guide

This document provides instructions for calibrating the Sensepoint XCD gas detector. It can be calibrated through either a response check or full calibration. The full calibration involves zeroing the detector using zero gas and then spanning it using calibration gas at concentrations between 25-75% of the sensor's range. Detailed steps are provided for accessing the calibration menu and completing the zero and span processes. Special instructions are given for hydrogen sulfide sensors, which can be affected by humidity changes.

Uploaded by

OMAR YESID MARTINEZ PENA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Calibration Guide

Sensepoint XCD
Calibration Handbook
Sensepoint XCD Calibration
It is recommended to periodically carry out a gas response check on the Sensepoint XCD to ensure correct
operation. This may be done in two ways;
1. A simple Response Check often referred to as a “BUMP TEST” is a test using calibration gas applied to
the sensor via the nozzle of the Weather Protection or using the Sensepoint XCD Gassing Cap.
If a BUMP TEST is done via the Weather Protection nozzle it may be necessary in windy conditions to
increase the flow rate of the test gas by a further 1 LPM, OR, to shelter the weather protection from the
wind.
2. A full gas calibration of the sensor as described in the following section, using ONLY the Sensepoint XCD
Gassing Cap (Part No.: S3KCAL).

Zero and Span


CAUTION
Before initial calibration allow the detector to stabilize for 30 minutes after applying power.
When in zeroing and span calibration mode the current output from the detector is inhibited (default 2mA) to
avoid false alarms.
For Flammable gas calibration use a calibration gas concentration of between 25%LEL and 75%LEL to ensure
that the required accuracy can be attained.
!"# $%&"!'()# *+,-&(# .%/(# 0()0!"0# "(1("# .!# 0(2.3!)# 456467# 8(1!"(# 2!)&+2.3)'# 9("!# :)&# 0/:)# 2:,38":.3!)6
To calibrate the detector, use an appropriate span gas cylinder, constant flow regulator AND the Sensepoint
XCD Gassing Cap. The flow rates used for calibration gas are as follows:
Gas Type Flow rate (L / Min)
Air or N2 for Zero 0.5 to 1.0
Flammable CAT 1 to 1.5
O2 0.5 to 1.0
H2S 0.5 to 1.0
CO 0.5 to 1.0
H2 0.5 to 1.0
NO2 0.5 to 1.0
Flammable IR 0.4 to 0.6
CO2 IR 0.4 to 0.6
A compressed air cylinder (20.9%Vol oxygen) should be used to perform the zero calibration if the area where
the detector is located contains any residual amount of the target gas. If no residual gas is present then the
background air can be used to perform the zero calibration. Contact your Honeywell Analytics representative
for details of suitable calibration kits.
To calibrate the detector follow the procedure below.
NOTE
!"#$%&'$%'()&*($'&%(+&)$,-.)$&/&0$)(.%#&1)(2$*-)$3&4/25#)(-%*&/.)&67839:;(<&(!"#$%=&2/%&>$&-'$*&+(&
'1/%&+?$&(!"#$%&'$%'()&.%&1</2$&(@&/&2(A1)$''$*&/.)&2"<.%*$)&67839:;(<&(!"#$%=3&B()&(!"#$%&'$%'()'&(%<"&
*(&1/)+'&CDEF&C7F&CG&6.@&2(A1)$''$*&/.)&2"<.%*$)&.'&-'$*=F&CEDCH&/%*&77&(@&+?$&1)(2$*-)$&>$<(I3

Sensepoint XCD 123


Calibration Handbook
Zero Calibration
1. If the ambient air is NOT considered reliable to use to set the ZERO, then remove the weather protection
and fit the Gassing Cap accessory onto the sensor and apply a clean source of zero gas or compressed air.
2. To access the calibration menu, hold the end of the magnet over the switch located at the top center of
the detector display (✓) for at least 3 seconds and then remove.
3. The display will indicate the first configuration mode menu ‘SEt CAL’.

4. Put the magnet over the ‘✓’ switch again and move to enter the Calibration menu.
5. The display will show the current gas reading, and the ‘ ’ icon flashes.

6. When the zero gas reading is stable use ‘✓’ to confirm zero calibration.
7. If successful the display shows ‘ZEro PASS’ (if not successful, the display shows ‘ZEro FAIL’ and returns
to configuration mode).

8. If using zero-air, turn it off. Zeroing is complete and saved.


9. The display shows ‘SPAn’ with ‘YES’ flashing.

10. If span calibration is required use ‘✓’ proceed to the next step. If span calibration is not required, use ‘ !’
to select ‘No’ and ‘✓’ to return to configuration mode.

124 Sensepoint XCD


Calibration Handbook
Span Calibration
11. The display shows the current calibration span gas concentration while flashing the ‘ ’ icon. Use ‘ !’ to
change the calibration span gas concentration, and ‘✓’ when required span calibration level is set.

12. The display will show the current gas reading, and the ‘ ’ icon flashes.
13. Connect the regulator to the span gas cylinder.
14. Apply the span gas to the sensor using the Sensepoint XCD Gassing Cap. The live gas reading is displayed.
When the reading is stable, use ‘✓’ to confirm span calibration.

15. If the sensor has been replaced the following display may be shown.

16. Use ‘ !’ to select ‘YES’ if the sensor has been replaced or ‘No’ if it has not been replaced.
17. If the span calibration is successful the instrument will briefly display ‘SPAn PASS’ (if fails ‘SPAN FAIL’
displayed and returns to configuration mode).
NOTE
J/<.>)/+.(%&*-$&I/)%.%#&2(-%+$)&.'&)$'$+&/@+$)&/&'-22$''@-<&2/<.>)/+.(%3

18. The display alternates between “Purg gAS” and the gas reading to indicate that the unit is expecting the
span gas to be removed from the sensor.

19. Promptly switch off the calibration span gas and remove the Sensepoint XCD Gassing Cap from the
sensor to allow the gas to disperse.

Sensepoint XCD 125


Calibration Handbook
20. When the reading falls below 50% of the calibration gas level the display indicates a countdown (up to
180 seconds dependant on gas type).

21. When the countdown is finished, the calibration procedure is complete.


22. The instrument returns to the ‘Set CAL’ menu. Activate the ‘ ’ or ‘!’ switch to select another menu or
select ‘QuIT’ to return to normal monitoring mode.

NOTE
K$A$A>$)&+(&/<I/"'&)$1</2$&+?$&L$/+?$)&M)(+$2+.(%&/%*&(+?$)&/22$''().$'3

Zero and Span Calibration of Hydrogen Sulfide sensors


Hydrogen Sulfide sensors can be affected by extreme humidity changes. A sudden increase in ambient humidity
can result in a short-term positive drift in the instrument’s reading. A sudden decrease in ambient humidity
can result in a short-term negative drift in the instrument’s reading. These are most likely to be noticed during
calibration with dry or cylinder gas.
When calibrating Hydrogen Sulfide cartridges the following should be taken into account while following the
Span/Zero procedure:
1. To zero the sensor, use a compressed air cylinder of 20.9%Vol oxygen (not Nitrogen). Do not use
background air.
2. Apply the gas to the sensor for three minutes before using ‘✓’ to confirm the zero calibration.
3. If a span calibration is to be performed, the span calibration gas should be applied to the sensor immediately
after the zeroing procedure. Do not allow the sensor to return to ambient air conditions between steps
2 and 3.
4. Apply the span gas for two minutes before using ‘✓’ to confirm the span calibration.

Authorized Distributor:
GasDetectorsUSA.com
Houston, TX USA
832-615-3588
[email protected]

126 Sensepoint XCD

You might also like