P.O.

Box 840687, Houston, Texas 77284

Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

Developed for Installation on a
Drillship
In Compliance with
API Specification 2C, 6th Edition 2004

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4469

Significant Wave Height = 1 feet (Seastate 1-2)

 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469A
Project Identification: JASCON 28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 22
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction QS816V/PZ371
Min. Breaking Strength of Boom Hoist Cable (kips) 235
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

API Specification 2C, 6th Edition 2004
 Safe Working Load Chart
Onboard Lifts
09-25-2007
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
Seatrax Crane Data Sheet (feet) SWL (lbs) SWL (lbs) SWL (lbs) SWL (lbs)
In Compliance with
40 308000c 390000c 466141a 55279d
API Specification 2C, 6th Edition, 2004 50 308000c 390000c 433175e 55279d
60 308000c 372993e 372993e 55279d
Serial or Quotation Number: 4469A 70 308000c 324350a 324350a 55279d
Project Identification: JASCON 28 80 283606a 283606a 283606a 55279d
90 251497a 251497a 251497a 55279d
Seatrax Series 115 Model 11532HD 100
110
225182a
203653a
225182a
203653a
225182a
203653a
55279d
55279d
180 Foot Boom 120
130
185200b
167972e
185200b
167972e
185200b
167972e
55279d
55279d
Calculated for Installation on a
140 150014e 150014e 150014e 55279d
Drillship 150 132884e 132884e 132884e 55279d
160 116078e 116078e 116078e 55279d
API General Method 170 98843e 98843e 98843e 55279d
180 79342e 79342e 79342e 55279d
Onboard Lifts 188 52449e 52449e 52449e 55279d

Significant Wave Height = 1 feet (Seastate 1-2)

Windspeed = 10 knots

Notes:
(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 5E-002 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
(12) The Minimum Personnel Rated Load at any Working Radius is 18426 lbs.
 Safe Working Load Chart
Offboard (Supply Boat)
09-25-2007
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
Seatrax Crane Data Sheet (feet) SWL (lbs) SWL (lbs) SWL (lbs) SWL (lbs)
In Compliance with 40 308000c 373334a 373334a 55279d
API Specification 2C, 6th Edition, 2004 50 308000c 343312e 343312e 55279d
60 306334e 306334e 306334e 55279d
Serial or Quotation Number: 4469A 70 274967e 274967e 274967e 55279d
Project Identification: JASCON 28 80 247171a 247171a 247171a 55279d
90 221655a 221655a 221655a 55279d
Seatrax Series 115 Model 11532HD 100
110
200824a
183174a
200824a
183174a
200824a
183174a
55279d
55279d
180 Foot Boom 120 167240e 167240e 167240e 55279d
130 150974e 150974e 150974e 55279d
Calculated for Installation on a 140 135542e 135542e 135542e 55279d
Drillship 150 120633e 120633e 120633e 55279d
160 105884e 105884e 105884e 55279d
API General Method 170 90755e 90755e 90755e 55279d
180 74127e 74127e 74127e 55279d
Offboard (Supply Boat) 188 51952is 51952is 51952is 51952is

Significant Wave Height = 1 feet (Seastate 1-2)

Windspeed = 10 knots

Notes:
(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 5E-002 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
(12) The Minimum Personnel Rated Load at any Working Radius is 18426 lbs.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet

Kingpost Reactions
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Boom Safe Working Vertical Primary Sideplane Torsional
Radius Angle Load Load Moment Moment Moment
(feet) (Degrees) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 81 466,141 1,540 52,541 7,421 1,634
50 77 433,175 1,471 59,527 6,892 1,918
60 74 372,993 1,344 61,244 5,987 2,029
70 71 324,350 1,242 62,320 5,239 2,109
80 67 283,606 1,157 62,811 4,597 2,164
90 64 251,497 1,089 63,362 4,071 2,216
100 60 225,182 1,034 63,872 3,620 2,263
110 56 203,653 989 64,456 3,227 2,310
120 52 185,200 950 64,954 2,870 2,352
130 48 167,972 914 65,027 2,525 2,378
140 44 150,014 876 64,153 2,171 2,371
150 39 132,884 840 62,794 1,823 2,346
160 33 116,078 805 60,825 1,473 2,299
170 27 98,843 769 57,982 1,106 2,220
180 18 79,342 728 53,504 688 2,085
188 3 52,449 671 44,597 134 1,794

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) SWLs Indicate the load limiting factor referenced in API Spec 2C, 6th Edition, 2004, Sec. 4.1.1
(3) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(4) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(5) The Primary Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(6) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(7) The Total Vertical Load is the summation, in KIPS, with 1.5 times SWL x Cv + dead loads.
(8) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Calculated Spring Constants and Cv
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working 8 Falls 10 Falls 12 Falls Auxiliary. Load Coefficients
Radius Spring Dynamic Spring Dynamic Spring Dynamic Spring Dynamic Boom Susp.
(feet) Constant Coef. Constant Coef. Constant Coef. Constant Coef. Coef. Coef.
40 254.00 1.40 303.00 1.40 349.29 1.40 31.00 1.40 1.93 0.90
50 237.00 1.40 279.00 1.40 317.16 1.40 31.00 1.40 2.02 1.04
60 220.00 1.40 256.00 1.40 287.64 1.40 31.00 1.40 2.11 1.17
70 205.00 1.40 235.00 1.40 260.72 1.40 31.00 1.40 2.19 1.29
80 190.00 1.40 215.00 1.40 236.13 1.40 31.00 1.40 2.27 1.42
90 176.00 1.40 196.00 1.40 213.57 1.40 31.00 1.40 2.35 1.54
100 162.00 1.40 179.00 1.40 192.76 1.40 30.00 1.40 2.42 1.66
110 148.00 1.40 162.00 1.40 173.49 1.40 30.00 1.40 2.50 1.78
120 136.00 1.40 147.00 1.40 155.55 1.40 30.00 1.40 2.57 1.91
130 123.00 1.40 132.00 1.40 138.78 1.40 30.00 1.40 2.64 2.04
140 111.00 1.40 118.00 1.40 122.99 1.40 29.00 1.40 2.71 2.18
150 99.00 1.40 104.00 1.40 108.03 1.40 29.00 1.40 2.79 2.34
160 87.00 1.40 91.00 1.40 93.64 1.40 29.00 1.40 2.88 2.52
170 75.00 1.40 77.00 1.40 79.40 1.40 28.00 1.40 2.98 2.73
180 62.00 1.40 63.00 1.40 64.27 1.40 27.00 1.40 3.12 3.01
188 44.00 1.40 45.00 1.40 45.70 1.40 25.00 1.40 3.39 3.52

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(12) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(13) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Total Offlead & Sidelead Forces
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working Total Offlead Equivalent Total Sidelead Equivalent
Radius Force (all causes) Offlead Angle Force (all causes) Sidelead Angle
(feet) (Pounds.) (Degrees) (Pounds) (Degrees)
40 33,510 2.500 28,605 1.000
50 31,496 2.500 26,941 1.000
60 27,821 2.500 23,903 1.000
70 24,851 2.500 21,448 1.000
80 22,363 2.500 19,391 1.000
90 20,402 2.500 17,770 1.000
100 18,795 2.500 16,442 1.000
110 17,480 2.500 15,355 1.000
120 16,353 2.500 14,424 1.000
130 15,301 2.500 13,554 1.000
140 14,205 2.500 12,647 1.000
150 13,159 2.500 11,783 1.000
160 12,132 2.500 10,934 1.000
170 11,080 2.500 10,064 1.000
180 9,889 2.500 9,080 1.000
188 8,247 2.500 7,723 1.000

(1) The Effects of Offlead, Sidelead & Windspeed are calculated in accordance with API Spec 2C, Par. 4.3.2 & 4.5.1
(2) The Sidelead & Offlead Forces acting at the boom tip due to Wind Loads are 182 lbs.
(3) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(4) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(5) The Total Offlead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation Trim Angle, & Lateral Foundation acceleration.
(6) The Total Sidelead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation List Angle, & Lateral Foundation acceleration.
(7) The Equivalent Offlead Angle is the Angle that the Hoistline is offset from the Vertical Plane, inline with the Boom, due to Supply Boat Position and Foundation Trim.
(8) The Equivalent Sidelead Angle is the Angle that the Hoistline is offset from the Vertical Plane, to the side of the Boom, due to Supply Boat Position and Foundation List.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Kingpost Reactions
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Boom Safe Working Vertical Primary Sideplane Torsional
Radius Angle Load Load Moment Moment Moment
(feet) (Degrees) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 81 373,334 1,345 50,806 8,590 1,892
50 77 343,312 1,282 55,633 7,934 2,208
60 74 306,334 1,204 58,065 7,133 2,417
70 71 274,967 1,139 59,964 6,440 2,593
80 67 247,171 1,080 61,270 5,813 2,736
90 64 221,655 1,027 61,918 5,230 2,846
100 60 200,824 983 62,640 4,734 2,959
110 56 183,174 946 63,329 4,296 3,074
120 52 167,240 912 63,763 3,887 3,185
130 48 150,974 878 63,425 3,470 3,268
140 44 135,542 846 62,672 3,064 3,347
150 39 120,633 814 61,448 2,664 3,427
160 33 105,884 783 59,645 2,258 3,524
170 27 90,755 752 57,052 1,831 3,675
180 18 74,127 717 53,146 1,338 4,052
188 3 51,952 670 45,216 547 7,298

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) SWLs Indicate the load limiting factor referenced in API Spec 2C, 6th Edition, 2004, Sec. 4.1.1
(3) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(4) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(5) The Primary Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(6) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(7) The Total Vertical Load is the summation, in KIPS, with 1.5 times SWL x Cv + dead loads.
(8) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Calculated Spring Constants and Cv
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working 8 Falls 10 Falls 12 Falls Auxiliary. Load Coefficients
Radius Spring Dynamic Spring Dynamic Spring Dynamic Spring Dynamic Boom Susp.
(feet) Constant Coef. Constant Coef. Constant Coef. Constant Coef. Coef. Coef.
40 242.00 1.40 287.00 1.40 327.54 1.40 31.00 1.60 2.16 1.14
50 226.00 1.40 264.00 1.40 297.74 1.40 31.00 1.60 2.21 1.25
60 210.00 1.40 242.00 1.40 270.39 1.40 31.00 1.60 2.27 1.36
70 195.00 1.40 222.00 1.40 245.48 1.40 31.00 1.59 2.34 1.47
80 181.00 1.40 204.00 1.40 222.72 1.40 30.00 1.59 2.41 1.58
90 167.00 1.40 186.00 1.40 201.81 1.40 30.00 1.59 2.47 1.69
100 154.00 1.40 170.00 1.40 182.50 1.40 30.00 1.59 2.53 1.81
110 142.00 1.40 154.00 1.40 164.59 1.40 30.00 1.59 2.60 1.93
120 130.00 1.40 140.00 1.40 147.87 1.40 30.00 1.58 2.66 2.05
130 118.00 1.40 126.00 1.40 132.21 1.40 29.00 1.58 2.72 2.18
140 106.00 1.40 112.00 1.40 117.45 1.40 29.00 1.58 2.78 2.32
150 95.00 1.40 100.00 1.40 103.43 1.40 29.00 1.57 2.84 2.47
160 84.00 1.40 87.00 1.40 89.93 1.40 28.00 1.57 2.91 2.64
170 72.00 1.40 75.00 1.40 76.60 1.40 28.00 1.56 2.99 2.84
180 60.00 1.40 61.00 1.40 62.60 1.40 27.00 1.55 3.07 3.10
188 48.00 1.40 48.00 1.40 49.14 1.40 26.00 1.53 2.76 3.27

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is .6
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is 5E-002 ft./sec.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(12) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(13) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Total Offlead & Sidelead Forces
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working Total Offlead Equivalent Total Sidelead Equivalent
Radius Force (all causes) Offlead Angle Force (all causes) Sidelead Angle
(feet) (Pounds.) (Degrees) (Pounds) (Degrees)
40 55,765 5.412 32,898 2.457
50 52,067 5.442 30,808 2.472
60 47,479 5.483 28,220 2.492
70 43,657 5.535 26,053 2.518
80 40,329 5.601 24,159 2.551
90 37,322 5.682 22,441 2.592
100 34,977 5.783 21,087 2.643
110 33,110 5.909 19,991 2.706
120 31,536 6.068 19,052 2.786
130 29,975 6.272 18,116 2.888
140 28,632 6.542 17,293 3.023
150 27,526 6.914 16,590 3.210
160 26,731 7.468 16,041 3.489
170 26,493 8.407 15,768 3.961
180 27,976 10.561 16,365 5.050
188 46,841 25.280 27,258 12.858

(1) The Effects of Offlead, Sidelead & Windspeed are calculated in accordance with API Spec 2C, Par. 4.3.2 & 4.5.1
(2) The Sidelead & Offlead Forces acting at the boom tip due to Wind Loads are 182 lbs.
(3) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(4) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(5) The Total Offlead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation Trim Angle, & Lateral Foundation acceleration.
(6) The Total Sidelead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation List Angle, & Lateral Foundation acceleration.
(7) The Equivalent Offlead Angle is the Angle that the Hoistline is offset from the Vertical Plane, inline with the Boom, due to Supply Boat Position and Foundation Trim.
(8) The Equivalent Sidelead Angle is the Angle that the Hoistline is offset from the Vertical Plane, to the side of the Boom, due to Supply Boat Position and Foundation List.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Theoretical Component Failure Mode Analysis
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Based Based Based Based Based Based Theor. Component Ratio
Radius on on on on on Main on Aux Fail First to
(feet) Kingpost Suspension Boom Gantry Cable Cable Load to Fail Kingpost
40 2033 2378 885 1107 2460 291 885 BOOM 2.297
50 1736 2166 882 968 2460 291 882 BOOM 1.967
60 1512 1981 872 855 2460 291 855 GANTRY 1.767
70 1337 1825 859 764 2460 291 764 GANTRY 1.75
80 1198 1690 844 691 2460 291 691 GANTRY 1.732
90 1083 1572 830 631 2460 291 631 GANTRY 1.715
100 988 1468 814 582 2460 291 582 GANTRY 1.698
110 907 1373 799 541 2460 291 541 GANTRY 1.678
120 838 1286 782 505 2460 291 505 GANTRY 1.661
130 779 1205 764 475 2460 291 475 GANTRY 1.638
140 727 1127 744 450 2460 291 450 GANTRY 1.615
150 682 1053 722 429 2460 291 429 GANTRY 1.586
160 642 979 678 413 2460 291 413 GANTRY 1.555
170 607 904 619 402 2460 291 402 GANTRY 1.509
180 580 820 541 402 2460 291 402 GANTRY 1.444
188 616 774 373 479 2460 291 373 BOOM 1.649

(1) All Loads are measured in KIPS

(2) Loads shown are calculated in accordance with API Spec 2C, 2004, Section 4.6.
(3) Ratio to Kingpost is the Ratio of the Component First to Fail to the Kingpost…The Aux line is Excluded from this Ratio.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 5E-002 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
3 22.00 Drum Width Between Flanges (in) 44
Motor Displacement (in /rev)
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
3 30.00 Drum Width Between Flanges (in) 69
Motor Displacement (in /rev)
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Main Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake
Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251
Single Line Performance
Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance - 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 468,219 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29
Main Drum Performance - 10 Part Line
Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 468,219 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22
Main Drum Performance -12 Part Line
Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

Developed for Installation on a
Drillship
In Compliance with
API Specification 2C, 6th Edition 2004

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4469

Significant Wave Height = 2.9 feet (Seastate 2-3)

 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469A
Project Identification: JASCON 28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 22
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction QS816V/PZ371
Min. Breaking Strength of Boom Hoist Cable (kips) 235
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

API Specification 2C, 6th Edition 2004
 Safe Working Load Chart
Onboard Lifts
09-25-2007
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
Seatrax Crane Data Sheet (feet) SWL (lbs) SWL (lbs) SWL (lbs) SWL (lbs)
In Compliance with
40 308000c 390000c 455557a 55279d
API Specification 2C, 6th Edition, 2004 50 308000c 390000c 433175e 55279d
60 308000c 372993e 372993e 55279d
Serial or Quotation Number: 4469A 70 308000c 324350a 324350a 55279d
Project Identification: JASCON 28 80 283606a 283606a 283606a 55279d
90 251497a 251497a 251497a 55279d
Seatrax Series 115 Model 11532HD 100
110
225182a
203653a
225182a
203653a
225182a
203653a
55279d
55279d
180 Foot Boom 120
130
185200b
167972e
185200b
167972e
185200b
167972e
55279d
55279d
Calculated for Installation on a
140 150014e 150014e 150014e 55279d
Drillship 150 132884e 132884e 132884e 55279d
160 116078e 116078e 116078e 55279d
API General Method 170 98843e 98843e 98843e 55279d
180 79342e 79342e 79342e 55279d
Onboard Lifts 188 52449e 52449e 52449e 55279d

Significant Wave Height = 2.9 feet (Seastate 2-3)

Windspeed = 15 knots

Notes:
(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is .42 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
(12) The Minimum Personnel Rated Load at any Working Radius is 16569 lbs.
 Safe Working Load Chart
Offboard (Supply Boat)
09-25-2007
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
Seatrax Crane Data Sheet (feet) SWL (lbs) SWL (lbs) SWL (lbs) SWL (lbs)
In Compliance with 40 308000c 344102a 344102a 55279d
API Specification 2C, 6th Edition, 2004 50 308000c 322342e 322342e 55279d
60 290257e 290257e 290257e 55279d
Serial or Quotation Number: 4469A 70 262215e 262215e 262215e 55279d
Project Identification: JASCON 28 80 237690e 237690e 237690e 55279d
90 214276a 214276a 214276a 55279d
Seatrax Series 115 Model 11532HD 100
110
194552a
177799a
194552a
177799a
194552a
177799a
55279d
55279d
180 Foot Boom 120 162087e 162087e 162087e 55279d
130 146593e 146593e 146593e 55279d
Calculated for Installation on a 140 131833e 131833e 131833e 55279d
Drillship 150 117534e 117534e 117534e 55279d
160 103377e 103377e 103377e 55279d
API General Method 170 88906e 88906e 88906e 55279d
180 73330e 73330e 73330e 55279d
Offboard (Supply Boat) 188 40333is 40333is 40333is 40333is

Significant Wave Height = 2.9 feet (Seastate 2-3)

Windspeed = 15 knots

Notes:
(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is .42 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
(12) The Minimum Personnel Rated Load at any Working Radius is 16569 lbs.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet

Kingpost Reactions
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Boom Safe Working Vertical Primary Sideplane Torsional
Radius Angle Load Load Moment Moment Moment
(feet) (Degrees) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 81 455,557 1,518 51,476 7,695 1,695
50 77 433,175 1,471 59,527 7,291 2,029
60 74 372,993 1,344 61,244 6,338 2,148
70 71 324,350 1,242 62,320 5,549 2,234
80 67 283,606 1,157 62,811 4,874 2,294
90 64 251,497 1,089 63,362 4,319 2,350
100 60 225,182 1,034 63,872 3,842 2,402
110 56 203,653 989 64,456 3,428 2,453
120 52 185,200 950 64,954 3,051 2,500
130 48 167,972 914 65,027 2,686 2,530
140 44 150,014 876 64,153 2,311 2,524
150 39 132,884 840 62,794 1,942 2,499
160 33 116,078 805 60,825 1,571 2,452
170 27 98,843 769 57,982 1,181 2,371
180 18 79,342 728 53,504 737 2,231
188 3 52,449 671 44,597 144 1,926

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) SWLs Indicate the load limiting factor referenced in API Spec 2C, 6th Edition, 2004, Sec. 4.1.1
(3) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(4) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(5) The Primary Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(6) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(7) The Total Vertical Load is the summation, in KIPS, with 1.5 times SWL x Cv + dead loads.
(8) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Calculated Spring Constants and Cv
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working 8 Falls 10 Falls 12 Falls Auxiliary. Load Coefficients
Radius Spring Dynamic Spring Dynamic Spring Dynamic Spring Dynamic Boom Susp.
(feet) Constant Coef. Constant Coef. Constant Coef. Constant Coef. Coef. Coef.
40 254.00 1.40 303.00 1.40 349.29 1.40 31.00 1.40 1.93 0.90
50 237.00 1.40 279.00 1.40 317.16 1.40 31.00 1.40 2.02 1.04
60 220.00 1.40 256.00 1.40 287.64 1.40 31.00 1.40 2.11 1.17
70 205.00 1.40 235.00 1.40 260.72 1.40 31.00 1.40 2.19 1.29
80 190.00 1.40 215.00 1.40 236.13 1.40 31.00 1.40 2.27 1.42
90 176.00 1.40 196.00 1.40 213.57 1.40 31.00 1.40 2.35 1.54
100 162.00 1.40 179.00 1.40 192.76 1.40 30.00 1.40 2.42 1.66
110 148.00 1.40 162.00 1.40 173.49 1.40 30.00 1.40 2.50 1.78
120 136.00 1.40 147.00 1.40 155.55 1.40 30.00 1.40 2.57 1.91
130 123.00 1.40 132.00 1.40 138.78 1.40 30.00 1.40 2.64 2.04
140 111.00 1.40 118.00 1.40 122.99 1.40 29.00 1.40 2.71 2.18
150 99.00 1.40 104.00 1.40 108.03 1.40 29.00 1.40 2.79 2.34
160 87.00 1.40 91.00 1.40 93.64 1.40 29.00 1.40 2.88 2.52
170 75.00 1.40 77.00 1.40 79.40 1.40 28.00 1.40 2.98 2.73
180 62.00 1.40 63.00 1.40 64.27 1.40 27.00 1.40 3.12 3.01
188 44.00 1.40 45.00 1.40 45.70 1.40 25.00 1.40 3.39 3.52

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(12) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(13) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Total Offlead & Sidelead Forces
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working Total Offlead Equivalent Total Sidelead Equivalent
Radius Force (all causes) Offlead Angle Force (all causes) Sidelead Angle
(feet) (Pounds.) (Degrees) (Pounds) (Degrees)
40 32,863 2.500 29,749 1.000
50 31,496 2.500 28,559 1.000
60 27,821 2.500 25,361 1.000
70 24,851 2.500 22,777 1.000
80 22,363 2.500 20,612 1.000
90 20,402 2.500 18,905 1.000
100 18,795 2.500 17,507 1.000
110 17,480 2.500 16,363 1.000
120 16,353 2.500 15,383 1.000
130 15,301 2.500 14,467 1.000
140 14,205 2.500 13,513 1.000
150 13,159 2.500 12,603 1.000
160 12,132 2.500 11,710 1.000
170 11,080 2.500 10,794 1.000
180 9,889 2.500 9,758 1.000
188 8,247 2.500 8,329 1.000

(1) The Effects of Offlead, Sidelead & Windspeed are calculated in accordance with API Spec 2C, Par. 4.3.2 & 4.5.1
(2) The Sidelead & Offlead Forces acting at the boom tip due to Wind Loads are 411 lbs.
(3) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(4) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(5) The Total Offlead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation Trim Angle, & Lateral Foundation acceleration.
(6) The Total Sidelead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation List Angle, & Lateral Foundation acceleration.
(7) The Equivalent Offlead Angle is the Angle that the Hoistline is offset from the Vertical Plane, inline with the Boom, due to Supply Boat Position and Foundation Trim.
(8) The Equivalent Sidelead Angle is the Angle that the Hoistline is offset from the Vertical Plane, to the side of the Boom, due to Supply Boat Position and Foundation List.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Kingpost Reactions
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Boom Safe Working Vertical Primary Sideplane Torsional
Radius Angle Load Load Moment Moment Moment
(feet) (Degrees) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 81 344,102 1,284 49,356 9,119 2,009
50 77 322,342 1,238 54,613 8,567 2,385
60 74 290,257 1,171 57,218 7,772 2,634
70 71 262,215 1,112 59,230 7,064 2,844
80 67 237,690 1,060 60,796 6,430 3,027
90 64 214,276 1,011 61,585 5,819 3,167
100 60 194,552 970 62,313 5,287 3,305
110 56 177,799 934 63,014 4,816 3,446
120 52 162,087 901 63,311 4,364 3,576
130 48 146,593 869 63,013 3,914 3,686
140 44 131,833 838 62,304 3,475 3,795
150 39 117,534 808 61,131 3,039 3,911
160 33 103,377 778 59,397 2,597 4,054
170 27 88,906 748 56,917 2,131 4,277
180 18 73,330 715 53,288 1,593 4,824
188 3 40,333 646 40,643 584 7,797

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) SWLs Indicate the load limiting factor referenced in API Spec 2C, 6th Edition, 2004, Sec. 4.1.1
(3) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(4) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(5) The Primary Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(6) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(7) The Total Vertical Load is the summation, in KIPS, with 1.5 times SWL x Cv + dead loads.
(8) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Calculated Spring Constants and Cv
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working 8 Falls 10 Falls 12 Falls Auxiliary. Load Coefficients
Radius Spring Dynamic Spring Dynamic Spring Dynamic Spring Dynamic Boom Susp.
(feet) Constant Coef. Constant Coef. Constant Coef. Constant Coef. Coef. Coef.
40 239.00 1.40 282.00 1.40 321.58 1.40 31.00 1.78 2.23 1.21
50 223.00 1.40 260.00 1.40 292.49 1.40 31.00 1.77 2.27 1.31
60 207.00 1.40 239.00 1.40 265.75 1.40 31.00 1.77 2.32 1.41
70 193.00 1.40 219.00 1.40 241.39 1.40 31.00 1.77 2.38 1.52
80 179.00 1.40 201.00 1.40 219.13 1.40 30.00 1.77 2.45 1.63
90 165.00 1.40 184.00 1.40 198.67 1.40 30.00 1.76 2.51 1.74
100 152.00 1.40 167.00 1.40 179.77 1.40 30.00 1.76 2.56 1.85
110 140.00 1.40 152.00 1.40 162.22 1.40 30.00 1.76 2.62 1.97
120 128.00 1.40 138.00 1.40 145.84 1.40 30.00 1.75 2.68 2.09
130 117.00 1.40 124.00 1.40 130.49 1.40 29.00 1.75 2.74 2.21
140 105.00 1.40 111.00 1.40 116.00 1.40 29.00 1.75 2.80 2.35
150 94.00 1.40 99.00 1.40 102.25 1.40 29.00 1.74 2.86 2.50
160 83.00 1.40 86.00 1.40 89.01 1.40 28.00 1.73 2.92 2.67
170 72.00 1.40 74.00 1.40 75.96 1.40 28.00 1.72 2.99 2.87
180 60.00 1.40 61.00 1.40 62.34 1.40 27.00 1.71 3.04 3.11
188 50.00 1.40 51.00 1.40 51.37 1.40 26.00 1.81 2.53 3.12

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 1.74
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is .42 ft./sec.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(12) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(13) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Total Offlead & Sidelead Forces
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working Total Offlead Equivalent Total Sidelead Equivalent
Radius Force (all causes) Offlead Angle Force (all causes) Sidelead Angle
(feet) (Pounds.) (Degrees) (Pounds) (Degrees)
40 59,454 6.265 34,978 2.884
50 56,454 6.304 33,294 2.904
60 51,916 6.356 30,762 2.930
70 48,030 6.424 28,584 2.964
80 44,718 6.508 26,718 3.006
90 41,602 6.614 24,956 3.059
100 39,101 6.744 23,528 3.125
110 37,128 6.907 22,383 3.207
120 35,387 7.112 21,361 3.310
130 33,763 7.375 20,398 3.442
140 32,389 7.723 19,564 3.617
150 31,297 8.203 18,875 3.858
160 30,596 8.916 18,385 4.218
170 30,622 10.123 18,266 4.828
180 32,955 12.883 19,362 6.234
188 47,345 31.014 29,165 16.197

(1) The Effects of Offlead, Sidelead & Windspeed are calculated in accordance with API Spec 2C, Par. 4.3.2 & 4.5.1
(2) The Sidelead & Offlead Forces acting at the boom tip due to Wind Loads are 411 lbs.
(3) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(4) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(5) The Total Offlead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation Trim Angle, & Lateral Foundation acceleration.
(6) The Total Sidelead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation List Angle, & Lateral Foundation acceleration.
(7) The Equivalent Offlead Angle is the Angle that the Hoistline is offset from the Vertical Plane, inline with the Boom, due to Supply Boat Position and Foundation Trim.
(8) The Equivalent Sidelead Angle is the Angle that the Hoistline is offset from the Vertical Plane, to the side of the Boom, due to Supply Boat Position and Foundation List.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Theoretical Component Failure Mode Analysis
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Based Based Based Based Based Based Theor. Component Ratio
Radius on on on on on Main on Aux Fail First to
(feet) Kingpost Suspension Boom Gantry Cable Cable Load to Fail Kingpost
40 1948 2235 821 1040 2460 291 821 BOOM 2.372
50 1673 2061 823 920 2460 291 823 BOOM 2.033
60 1464 1901 815 820 2460 291 815 BOOM 1.796
70 1300 1761 805 737 2460 291 737 GANTRY 1.764
80 1168 1638 792 670 2460 291 670 GANTRY 1.743
90 1059 1530 778 613 2460 291 613 GANTRY 1.725
100 968 1432 765 567 2460 291 567 GANTRY 1.705
110 891 1343 750 527 2460 291 527 GANTRY 1.688
120 824 1260 735 494 2460 291 494 GANTRY 1.667
130 767 1183 717 466 2460 291 466 GANTRY 1.644
140 717 1109 698 442 2460 291 442 GANTRY 1.621
150 673 1037 676 422 2460 291 422 GANTRY 1.592
160 635 967 644 407 2460 291 407 GANTRY 1.558
170 602 894 587 398 2460 291 398 GANTRY 1.512
180 578 816 509 400 2460 291 400 GANTRY 1.444
188 644 815 337 505 2460 291 337 BOOM 1.909

(1) All Loads are measured in KIPS

(2) Loads shown are calculated in accordance with API Spec 2C, 2004, Section 4.6.
(3) Ratio to Kingpost is the Ratio of the Component First to Fail to the Kingpost…The Aux line is Excluded from this Ratio.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is .42 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
3 22.00 Drum Width Between Flanges (in) 44
Motor Displacement (in /rev)
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
3 30.00 Drum Width Between Flanges (in) 69
Motor Displacement (in /rev)
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Main Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake
Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251
Single Line Performance
Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance - 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 468,219 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29
Main Drum Performance - 10 Part Line
Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 468,219 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22
Main Drum Performance -12 Part Line
Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

Developed for Installation on a
Drillship
In Compliance with
API Specification 2C, 6th Edition 2004

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4469

Significant Wave Height = 6.9 feet (Seastate 4-5)

 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469A
Project Identification: JASCON 28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 22
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction QS816V/PZ371
Min. Breaking Strength of Boom Hoist Cable (kips) 235
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

API Specification 2C, 6th Edition 2004
 Safe Working Load Chart
Onboard Lifts
09-25-2007
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
Seatrax Crane Data Sheet (feet) SWL (lbs) SWL (lbs) SWL (lbs) SWL (lbs)
In Compliance with
40 302561a 302561a 302561a 55279d
API Specification 2C, 6th Edition, 2004 50 298825a 298825a 298825a 55279d
60 293688a 293688a 293688a 55279d
Serial or Quotation Number: 4469A 70 288621a 288621a 288621a 55279d
Project Identification: JASCON 28 80 283606a 283606a 283606a 55279d
90 251497a 251497a 251497a 55279d
Seatrax Series 115 Model 11532HD 100
110
225182a
198888is
225182a
198888is
225182a
198888is
55279d
55279d
180 Foot Boom 120
130
174270is
153322is
174270is
153322is
174270is
153322is
55279d
55279d
Calculated for Installation on a
140 135425is 135425is 135425is 55279d
Drillship 150 119797is 119797is 119797is 55279d
160 106211is 106211is 106211is 55279d
API General Method 170 94253is 94253is 94253is 55279d
180 79342e 79342e 79342e 55279d
Onboard Lifts 188 52449e 52449e 52449e 55279d

Significant Wave Height = 6.9 feet (Seastate 4-5)

Windspeed = 20 knots

Notes:
(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 2.38 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
(12) The Minimum Personnel Rated Load at any Working Radius is 4429 lbs.
 Safe Working Load Chart
Offboard (Supply Boat)
09-25-2007
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
Seatrax Crane Data Sheet (feet) SWL (lbs) SWL (lbs) SWL (lbs) SWL (lbs)
In Compliance with 40 152640a 147415a 140017a 49204c
API Specification 2C, 6th Edition, 2004 50 159873a 155158a 148654a 49323c
60 164068a 159923a 154348a 49441c
Serial or Quotation Number: 4469A 70 166726a 163153a 158465a 49556c
Project Identification: JASCON 28 80 155043a 152183a 148490a 49670c
90 139539a 137341a 134545a 49785c
Seatrax Series 115 Model 11532HD 100
110
126547a
116201a
124896a
115001a
122833a
113536a
49906c
50036c
180 Foot Boom 120 107684a 106861a 105890a 50182c
130 100998a 100491a 99930a 50351c
Calculated for Installation on a 140 95843a 95606a 95385a 50554c
Drillship 150 87119is 87119is 87119is 50805c
160 73765is 73765is 73765is 51129c
API General Method 170 60509is 60509is 60509is 51567c
180 45263is 45263is 45263is 45263is
Offboard (Supply Boat) 188 N/A N/A N/A 13287ih

Significant Wave Height = 6.9 feet (Seastate 4-5)

Windspeed = 20 knots

Notes:
(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 2.38 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
(12) The Minimum Personnel Rated Load at any Working Radius is 4429 lbs.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet

Kingpost Reactions
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Boom Safe Working Vertical Primary Sideplane Torsional
Radius Angle Load Load Moment Moment Moment
(feet) (Degrees) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 81 302,561 1,196 36,080 12,219 2,692
50 77 298,825 1,189 43,210 11,966 3,331
60 74 293,688 1,178 49,966 11,630 3,941
70 71 288,621 1,167 56,499 11,261 4,534
80 67 283,606 1,157 62,811 10,856 5,110
90 64 251,497 1,089 63,362 9,603 5,226
100 60 225,182 1,034 63,872 8,529 5,331
110 56 198,888 979 63,288 7,465 5,342
120 52 174,270 927 62,053 6,461 5,294
130 48 153,322 883 60,843 5,566 5,243
140 44 135,425 845 59,692 4,755 5,193
150 39 119,797 813 58,532 3,995 5,140
160 33 106,211 784 57,417 3,261 5,090
170 27 94,253 759 56,307 2,511 5,041
180 18 79,342 728 53,504 1,602 4,853
188 3 52,449 671 44,597 311 4,151

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) SWLs Indicate the load limiting factor referenced in API Spec 2C, 6th Edition, 2004, Sec. 4.1.1
(3) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(4) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(5) The Primary Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(6) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(7) The Total Vertical Load is the summation, in KIPS, with 1.5 times SWL x Cv + dead loads.
(8) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Calculated Spring Constants and Cv
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working 8 Falls 10 Falls 12 Falls Auxiliary. Load Coefficients
Radius Spring Dynamic Spring Dynamic Spring Dynamic Spring Dynamic Boom Susp.
(feet) Constant Coef. Constant Coef. Constant Coef. Constant Coef. Coef. Coef.
40 254.00 1.40 303.00 1.40 349.29 1.40 31.00 1.40 1.93 0.90
50 237.00 1.40 279.00 1.40 317.16 1.40 31.00 1.40 2.02 1.04
60 220.00 1.40 256.00 1.40 287.64 1.40 31.00 1.40 2.11 1.17
70 205.00 1.40 235.00 1.40 260.72 1.40 31.00 1.40 2.19 1.29
80 190.00 1.40 215.00 1.40 236.13 1.40 31.00 1.40 2.27 1.42
90 176.00 1.40 196.00 1.40 213.57 1.40 31.00 1.40 2.35 1.54
100 162.00 1.40 179.00 1.40 192.76 1.40 30.00 1.40 2.42 1.66
110 148.00 1.40 162.00 1.40 173.49 1.40 30.00 1.40 2.50 1.78
120 136.00 1.40 147.00 1.40 155.55 1.40 30.00 1.40 2.57 1.91
130 123.00 1.40 132.00 1.40 138.78 1.40 30.00 1.40 2.64 2.04
140 111.00 1.40 118.00 1.40 122.99 1.40 29.00 1.40 2.71 2.18
150 99.00 1.40 104.00 1.40 108.03 1.40 29.00 1.40 2.79 2.34
160 87.00 1.40 91.00 1.40 93.64 1.40 29.00 1.40 2.88 2.52
170 75.00 1.40 77.00 1.40 79.40 1.40 28.00 1.40 2.98 2.73
180 62.00 1.40 63.00 1.40 64.27 1.40 27.00 1.40 3.12 3.01
188 44.00 1.40 45.00 1.40 45.70 1.40 25.00 1.40 3.39 3.52

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(12) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(13) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Total Offlead & Sidelead Forces
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Onboard Lifts
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working Total Offlead Equivalent Total Sidelead Equivalent
Radius Force (all causes) Offlead Angle Force (all causes) Sidelead Angle
(feet) (Pounds.) (Degrees) (Pounds) (Degrees)
40 23,520 2.500 47,871 1.000
50 23,292 2.500 47,421 1.000
60 22,978 2.500 46,802 1.000
70 22,669 2.500 46,191 1.000
80 22,363 2.500 45,587 1.000
90 20,402 2.500 41,719 1.000
100 18,795 2.500 38,548 1.000
110 17,189 2.500 35,380 1.000
120 15,686 2.500 32,414 1.000
130 14,407 2.500 29,890 1.000
140 13,314 2.500 27,734 1.000
150 12,359 2.500 25,851 1.000
160 11,530 2.500 24,214 1.000
170 10,799 2.500 22,774 1.000
180 9,889 2.500 20,977 1.000
188 8,247 2.500 17,737 1.000

(1) The Effects of Offlead, Sidelead & Windspeed are calculated in accordance with API Spec 2C, Par. 4.3.2 & 4.5.1
(2) The Sidelead & Offlead Forces acting at the boom tip due to Wind Loads are 731 lbs.
(3) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(4) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(5) The Total Offlead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation Trim Angle, & Lateral Foundation acceleration.
(6) The Total Sidelead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation List Angle, & Lateral Foundation acceleration.
(7) The Equivalent Offlead Angle is the Angle that the Hoistline is offset from the Vertical Plane, inline with the Boom, due to Supply Boat Position and Foundation Trim.
(8) The Equivalent Sidelead Angle is the Angle that the Hoistline is offset from the Vertical Plane, to the side of the Boom, due to Supply Boat Position and Foundation List.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Kingpost Reactions
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Boom Safe Working Vertical Primary Sideplane Torsional
Radius Angle Load Load Moment Moment Moment
(feet) (Degrees) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 81 140,017 1,056 38,736 12,028 2,650
50 77 148,654 1,063 45,445 12,063 3,358
60 74 154,348 1,062 51,657 11,927 4,042
70 71 158,465 1,059 57,512 11,693 4,708
80 67 148,490 1,024 59,995 10,850 5,107
90 64 134,545 981 60,859 9,852 5,362
100 60 122,833 944 61,592 8,956 5,598
110 56 113,536 913 62,404 8,163 5,842
120 52 105,890 886 63,206 7,436 6,093
130 48 99,930 864 64,111 6,767 6,373
140 44 95,385 844 65,111 6,134 6,699
150 39 87,119 815 63,880 5,322 6,848
160 33 73,765 773 59,753 4,326 6,751
170 27 60,509 731 54,866 3,336 6,696
180 18 45,263 695 50,242 2,361 7,148
188 3 13,287 589 29,754 551 7,359

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) SWLs Indicate the load limiting factor referenced in API Spec 2C, 6th Edition, 2004, Sec. 4.1.1
(3) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(4) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(5) The Primary Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(6) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
(7) The Total Vertical Load is the summation, in KIPS, with 1.5 times SWL x Cv + dead loads.
(8) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.5 times SWL x Cv & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Calculated Spring Constants and Cv
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working 8 Falls 10 Falls 12 Falls Auxiliary. Load Coefficients
Radius Spring Dynamic Spring Dynamic Spring Dynamic Spring Dynamic Boom Susp.
(feet) Constant Coef. Constant Coef. Constant Coef. Constant Coef. Coef. Coef.
40 232.00 2.07 273.00 2.14 309.63 2.24 31.00 2.30 2.38 1.36
50 217.00 2.01 251.00 2.07 282.04 2.15 31.00 2.29 2.39 1.44
60 202.00 1.97 231.00 2.01 256.55 2.08 31.00 2.28 2.42 1.53
70 187.00 1.93 212.00 1.96 233.30 2.02 30.00 2.28 2.47 1.63
80 174.00 1.92 195.00 1.95 212.04 2.00 30.00 2.27 2.52 1.73
90 161.00 1.93 178.00 1.96 192.49 1.99 30.00 2.27 2.58 1.83
100 149.00 1.93 163.00 1.95 174.39 1.98 30.00 2.26 2.63 1.94
110 137.00 1.93 148.00 1.94 157.58 1.97 30.00 2.26 2.68 2.05
120 125.00 1.92 134.00 1.93 141.87 1.94 29.00 2.25 2.73 2.17
130 114.00 1.90 121.00 1.91 127.13 1.91 29.00 2.24 2.78 2.29
140 103.00 1.87 109.00 1.88 113.22 1.88 29.00 2.24 2.83 2.42
150 92.00 1.84 96.00 1.84 100.01 1.84 28.00 2.23 2.88 2.57
160 82.00 1.81 85.00 1.81 87.31 1.80 28.00 2.21 2.93 2.73
170 71.00 1.77 73.00 1.76 74.85 1.75 27.00 2.19 2.97 2.91
180 60.00 1.82 61.00 1.81 62.12 1.80 27.00 2.17 2.97 3.13
188 56.00 56.00 57.37 28.00 3.27 2.06 2.78

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 4.14
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is N/A
(5) The available 4 Fall Hook Speed in ft/sec is N/A
(6) The available 6 Fall Hook Speed in ft/sec is N/A
(7) The available 8 Fall Hook Speed in ft/sec is N/A
(8) The available 10 Fall Hook Speed in ft/sec is N/A
(9) The available 12 Fall Hook Speed in ft/sec is N/A
(10) The Specified Boom Tip Velocity caused by Foundation Motions is 2.38 ft./sec.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(12) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(13) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Total Offlead & Sidelead Forces
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working Total Offlead Equivalent Total Sidelead Equivalent
Radius Force (all causes) Offlead Angle Force (all causes) Sidelead Angle
(feet) (Pounds.) (Degrees) (Pounds) (Degrees)
40 53,952 8.055 47,171 3.784
50 54,965 8.113 47,783 3.813
60 55,423 8.189 47,919 3.852
70 55,684 8.288 47,850 3.901
80 53,043 8.413 45,566 3.964
90 49,675 8.568 42,724 4.042
100 46,929 8.759 40,327 4.139
110 44,867 8.998 38,410 4.259
120 43,352 9.299 36,855 4.411
130 42,454 9.685 35,688 4.606
140 42,216 10.194 34,903 4.864
150 41,091 10.896 33,439 5.220
160 38,772 11.936 31,136 5.750
170 37,224 13.689 29,262 6.648
180 39,379 17.651 29,480 8.710
188 34,667 41.261 29,123 22.873

(1) The Effects of Offlead, Sidelead & Windspeed are calculated in accordance with API Spec 2C, Par. 4.3.2 & 4.5.1
(2) The Sidelead & Offlead Forces acting at the boom tip due to Wind Loads are 731 lbs.
(3) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(4) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(5) The Total Offlead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation Trim Angle, & Lateral Foundation acceleration.
(6) The Total Sidelead Force includes the effects of Wind, Supply Boat Position, Dynamic Coefficient, Foundation List Angle, & Lateral Foundation acceleration.
(7) The Equivalent Offlead Angle is the Angle that the Hoistline is offset from the Vertical Plane, inline with the Boom, due to Supply Boat Position and Foundation Trim.
(8) The Equivalent Sidelead Angle is the Angle that the Hoistline is offset from the Vertical Plane, to the side of the Boom, due to Supply Boat Position and Foundation List.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Theoretical Component Failure Mode Analysis
(In Compliance with API Specification 2C, 6th Edition, 2004)
Seatrax Series 115 Model 11532HD
180 Foot Boom With Walkways
Offboard (Supply Boat)
Drillship API General Method
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Quotation / Serial No. 4469A Identification JASCON 28
Working Based Based Based Based Based Based Theor. Component Ratio
Radius on on on on on Main on Aux Fail First to
(feet) Kingpost Suspension Boom Gantry Cable Cable Load to Fail Kingpost
40 1793 1979 590 923 2460 291 590 BOOM 3.034
50 1557 1870 597 834 2460 291 597 BOOM 2.608
60 1375 1752 596 755 2460 291 596 BOOM 2.306
70 1229 1641 591 686 2460 291 591 BOOM 2.078
80 1111 1540 586 628 2460 291 586 BOOM 1.895
90 1012 1448 579 579 2460 291 579 BOOM 1.746
100 929 1363 572 538 2460 291 538 GANTRY 1.725
110 858 1284 564 503 2460 291 503 GANTRY 1.705
120 797 1211 555 474 2460 291 474 GANTRY 1.681
130 743 1141 545 448 2460 291 448 GANTRY 1.657
140 697 1073 533 427 2460 291 427 GANTRY 1.631
150 656 1008 519 409 2460 291 409 GANTRY 1.602
160 621 943 500 396 2460 291 396 GANTRY 1.567
170 592 878 474 390 2460 291 390 GANTRY 1.518
180 575 813 425 398 2460 291 398 GANTRY 1.444
188 683 925 257 576 2460 291 257 BOOM 2.656

(1) All Loads are measured in KIPS

(2) Loads shown are calculated in accordance with API Spec 2C, 2004, Section 4.6.
(3) Ratio to Kingpost is the Ratio of the Component First to Fail to the Kingpost…The Aux line is Excluded from this Ratio.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 2.38 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
3 22.00 Drum Width Between Flanges (in) 44
Motor Displacement (in /rev)
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-25-2007
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
3 30.00 Drum Width Between Flanges (in) 69
Motor Displacement (in /rev)
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Main Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake
Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251
Single Line Performance
Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance - 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 468,219 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29
Main Drum Performance - 10 Part Line
Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 468,219 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22
Main Drum Performance -12 Part Line
Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

In Compliance with
ASME B30.8 / ABS Heavy Lift

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
JASCON 30
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4456
4469

The Specified Sidelead Angle (List) is 1 deg.

The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469
4456
Project Identification: JASCON
JASCON2830
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 21.5
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction
Min. Breaking Strength of Boom Hoist Cable (kips)
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

ASME B30.8 / ABS Heavy Lift
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet

ASME B30.8 / ABS Heavy Lift Safe Working Load Chart

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 1 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or
Serial or Quotation
QuotationNumber:
Number:4469
4456 Project Identification:
Project Identification: JASCON
JASCON 2830
8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Working
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 599412c 55279d
50 409063c 506122c 599412c 55279d
60 409063c 499844e 499844e 55279d
70 409063c 427679e 427679e 55279d
80 372968e 372968e 372968e 55279d
90 329334e 329334e 329334e 55279d
100 293161e 293161e 293161e 55279d
110 262230e 262230e 262230e 55279d
120 235084e 235084e 235084e 55279d
130 210705e 210705e 210705e 55279d
140 188318e 188318e 188318e 55279d
150 167266e 167266e 167266e 55279d
160 146875e 146875e 146875e 55279d
170 126204e 126204e 126204e 55279d
180 103080e 103080e 103080e 55279d
188 71581e 71581e 71581e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 1 deg.
(8) The Specified Offlead Angle (Trim) is 0 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Kingpost Reactions - ASME B30.8/ ABS Heavy Lift
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 1 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or
Serial or Quotation
Quotation Number:
Number:4469
4456 ProjectIdentification:
Project Identification: JASCON
JASCON28 30
Working Safe Working Vertical Primary Sideplane Torsional
Radius Load Load Moment Moment Moment
(feet) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 599,412 1,167 29,991 4,004 882
50 599,412 1,167 37,624 3,960 1,102
60 499,844 1,057 38,684 3,322 1,126
70 427,679 978 39,664 2,848 1,147
80 372,968 917 40,592 2,478 1,166
90 329,334 869 41,414 2,172 1,182
100 293,161 830 42,095 1,911 1,194
110 262,230 796 42,616 1,679 1,201
120 235,084 766 42,955 1,468 1,203
130 210,705 739 43,093 1,273 1,199
140 188,318 714 43,002 1,087 1,188
150 167,266 691 42,638 908 1,168
160 146,875 669 41,927 729 1,138
170 126,204 646 40,715 545 1,094
180 103,080 620 38,563 337 1,021
188 71,581 586 33,757 65 870

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(3) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(4) The Primary Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(5) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(6) The Total Vertical Load is the summation, in KIPS, with 1.1 times SWL + dead loads.
(7) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet

Cv and Spring Constants

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 1 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serialor
or Quotation
Quotation Number: Project Identification: JASCON 28
Serial Number: 4469
4456 Project Identification: JASCON 30
8 Falls 10 Falls 12 Falls Auxiliary.
Working Spring Fixed Spring Fixed Spring Fixed Spring Fixed
Radius Constant Dynamic Constant Dynamic Constant Dynamic Constant Dynamic
(feet) (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef.
40 262 1.1 315 1.1 364 1.1 31 1.1
50 243 1.1 288 1.1 329 1.1 31 1.1
60 225 1.1 263 1.1 296 1.1 31 1.1
70 208 1.1 239 1.1 266 1.1 31 1.1
80 192 1.1 218 1.1 240 1.1 31 1.1
90 177 1.1 198 1.1 215 1.1 31 1.1
100 162 1.1 179 1.1 193 1.1 30 1.1
110 148 1.1 161 1.1 172 1.1 30 1.1
120 134 1.1 145 1.1 154 1.1 30 1.1
130 121 1.1 129 1.1 136 1.1 30 1.1
140 108 1.1 115 1.1 120 1.1 29 1.1
150 96 1.1 101 1.1 105 1.1 29 1.1
160 84 1.1 87 1.1 90 1.1 28 1.1
170 72 1.1 74 1.1 76 1.1 28 1.1
180 58 1.1 59 1.1 61 1.1 26 1.1
188 42 1.1 42 1.1 43 1.1 24 1.1

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 0
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
4469
Serial or Quotation Number: 4456 JASCON 28
Project Identification: JASCON 30
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 22.00 Drum Width Between Flanges (in) 44
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
4469
Serial or Quotation Number: 4456 JASCON 2830
Project Identification: JASCON
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 30.00 Drum Width Between Flanges (in) 69
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance- 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 496,448 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29

Main Drum Performance - 10 Part Line

Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 560,776 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22

Main Drum Performance - 12 Part Line

Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 08-07-2006
Seatrax Crane Data Sheet
ASME B30.8 / ABS Heavy Lift Safe Working Load Chart
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 1 deg. The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
SerialororQuotation
Serial Quotation Number:
Number:4469
4456 Project Identification:
Project Identification:JASCON 28 30
JASCON
Working 8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 599412c 55279d
50 409063c 506122c 599412c 55279d
60 409063c 499844e 499844e 55279d
70 409063c 427679e 427679e 55279d
80 372968e 372968e 372968e 55279d
90 329334e 329334e 329334e 55279d
100 293161e 293161e 293161e 55279d
110 262230e 262230e 262230e 55279d
120 235084e 235084e 235084e 55279d
130 210705e 210705e 210705e 55279d
140 188318e 188318e 188318e 55279d
150 167266e 167266e 167266e 55279d
160 146875e 146875e 146875e 55279d
170 126204e 126204e 126204e 55279d
180 103080e 103080e 103080e 55279d
188 71581e 71581e 71581e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 1 deg.
(8) The Specified Offlead Angle (Trim) is 0 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

In Compliance with
ASME B30.8 / ABS Heavy Lift

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 30
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4456
4469

The Specified Sidelead Angle (List) is 2.5 deg.

The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469
4456
Project Identification: JASCON 30
28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 21.5
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction
Min. Breaking Strength of Boom Hoist Cable (kips)
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

ASME B30.8 / ABS Heavy Lift
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet

ASME B30.8 / ABS Heavy Lift Safe Working Load Chart

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
4469
Serial or Quotation Number: 4456 Project Identification: JASCON 28
30
8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Working
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 599412c 55279d
50 409063c 506122c 592898a 55279d
60 409063c 499844e 499844e 55279d
70 409063c 427679e 427679e 55279d
80 372968e 372968e 372968e 55279d
90 329334e 329334e 329334e 55279d
100 293161e 293161e 293161e 55279d
110 262230e 262230e 262230e 55279d
120 235084e 235084e 235084e 55279d
130 210705e 210705e 210705e 55279d
140 188318e 188318e 188318e 55279d
150 167266e 167266e 167266e 55279d
160 146875e 146875e 146875e 55279d
170 126204e 126204e 126204e 55279d
180 103080e 103080e 103080e 55279d
188 71581e 71581e 71581e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 2.5 deg.
(8) The Specified Offlead Angle (Trim) is 0 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Kingpost Reactions - ASME B30.8/ ABS Heavy Lift
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 28
30
Working Safe Working Vertical Primary Sideplane Torsional
Radius Load Load Moment Moment Moment
(feet) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 599,412 1,167 29,991 8,784 1,935
50 592,898 1,159 37,266 8,605 2,395
60 499,844 1,057 38,684 7,295 2,472
70 427,679 978 39,664 6,259 2,520
80 372,968 917 40,592 5,450 2,565
90 329,334 869 41,414 4,782 2,603
100 293,161 830 42,095 4,210 2,631
110 262,230 796 42,616 3,702 2,649
120 235,084 766 42,955 3,241 2,656
130 210,705 739 43,093 2,812 2,649
140 188,318 714 43,002 2,405 2,627
150 167,266 691 42,638 2,010 2,587
160 146,875 669 41,927 1,617 2,524
170 126,204 646 40,715 1,210 2,429
180 103,080 620 38,563 750 2,272
188 71,581 586 33,757 145 1,944

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(3) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(4) The Primary Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(5) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(6) The Total Vertical Load is the summation, in KIPS, with 1.1 times SWL + dead loads.
(7) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet

Cv and Spring Constants

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 2830
8 Falls 10 Falls 12 Falls Auxiliary.
Working Spring Fixed Spring Fixed Spring Fixed Spring Fixed
Radius Constant Dynamic Constant Dynamic Constant Dynamic Constant Dynamic
(feet) (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef.
40 262 1.1 315 1.1 364 1.1 31 1.1
50 243 1.1 288 1.1 329 1.1 31 1.1
60 225 1.1 263 1.1 296 1.1 31 1.1
70 208 1.1 239 1.1 266 1.1 31 1.1
80 192 1.1 218 1.1 240 1.1 31 1.1
90 177 1.1 198 1.1 215 1.1 31 1.1
100 162 1.1 179 1.1 193 1.1 30 1.1
110 148 1.1 161 1.1 172 1.1 30 1.1
120 134 1.1 145 1.1 154 1.1 30 1.1
130 121 1.1 129 1.1 136 1.1 30 1.1
140 108 1.1 115 1.1 120 1.1 29 1.1
150 96 1.1 101 1.1 105 1.1 29 1.1
160 84 1.1 87 1.1 90 1.1 28 1.1
170 72 1.1 74 1.1 76 1.1 28 1.1
180 58 1.1 59 1.1 61 1.1 26 1.1
188 42 1.1 42 1.1 43 1.1 24 1.1

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 0
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 28
30
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 22.00 Drum Width Between Flanges (in) 44
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469
4456 Project Identification: JASCON28 30
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 30.00 Drum Width Between Flanges (in) 69
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance- 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 496,448 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29

Main Drum Performance - 10 Part Line

Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 560,776 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22

Main Drum Performance - 12 Part Line

Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 08-07-2006
Seatrax Crane Data Sheet
ASME B30.8 / ABS Heavy Lift Safe Working Load Chart
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg. The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 28
30
Working 8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 599412c 55279d
50 409063c 506122c 592898a 55279d
60 409063c 499844e 499844e 55279d
70 409063c 427679e 427679e 55279d
80 372968e 372968e 372968e 55279d
90 329334e 329334e 329334e 55279d
100 293161e 293161e 293161e 55279d
110 262230e 262230e 262230e 55279d
120 235084e 235084e 235084e 55279d
130 210705e 210705e 210705e 55279d
140 188318e 188318e 188318e 55279d
150 167266e 167266e 167266e 55279d
160 146875e 146875e 146875e 55279d
170 126204e 126204e 126204e 55279d
180 103080e 103080e 103080e 55279d
188 71581e 71581e 71581e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 2.5 deg.
(8) The Specified Offlead Angle (Trim) is 0 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

In Compliance with
ASME B30.8 / ABS Heavy Lift

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON
JASCON28 30
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4456
4469

The Specified Sidelead Angle (List) is 2.5 deg.

The Specified Offlead Angle (Trim) is 1 deg.
Windspeed = 10 knots
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469
4456
Project Identification: JASCON 30
28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 21.5
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction
Min. Breaking Strength of Boom Hoist Cable (kips)
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

ASME B30.8 / ABS Heavy Lift
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet

ASME B30.8 / ABS Heavy Lift Safe Working Load Chart

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg.
The Specified Offlead Angle (Trim) is 1 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 28
30
8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Working
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 593301a 55279d
50 409063c 506122c 549226e 55279d
60 409063c 464263e 464263e 55279d
70 402024e 402024e 402024e 55279d
80 353678e 353678e 353678e 55279d
90 314421e 314421e 314421e 55279d
100 281420e 281420e 281420e 55279d
110 252883e 252883e 252883e 55279d
120 227606e 227606e 227606e 55279d
130 204728e 204728e 204728e 55279d
140 183579e 183579e 183579e 55279d
150 163575e 163575e 163575e 55279d
160 144098e 144098e 144098e 55279d
170 124260e 124260e 124260e 55279d
180 101965e 101965e 101965e 55279d
188 71440e 71440e 71440e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 2.5 deg.
(8) The Specified Offlead Angle (Trim) is 1 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Kingpost Reactions - ASME B30.8/ ABS Heavy Lift
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg.
The Specified Offlead Angle (Trim) is 1 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 28
30
Working Safe Working Vertical Primary Sideplane Torsional
Radius Load Load Moment Moment Moment
(feet) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 593,301 1,160 33,189 8,704 1,917
50 549,226 1,111 38,064 8,039 2,238
60 464,263 1,018 39,057 6,841 2,318
70 402,024 949 40,050 5,938 2,391
80 353,678 896 40,966 5,213 2,454
90 314,421 853 41,766 4,605 2,506
100 281,420 817 42,421 4,074 2,547
110 252,883 785 42,912 3,599 2,575
120 227,606 757 43,222 3,162 2,591
130 204,728 732 43,329 2,753 2,593
140 183,579 709 43,206 2,361 2,579
150 163,575 687 42,812 1,979 2,547
160 144,098 666 42,069 1,597 2,492
170 124,260 644 40,825 1,198 2,405
180 101,965 619 38,636 745 2,257
188 71,440 586 33,785 145 1,942

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(3) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(4) The Primary Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(5) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(6) The Total Vertical Load is the summation, in KIPS, with 1.1 times SWL + dead loads.
(7) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet

Cv and Spring Constants

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg.
The Specified Offlead Angle (Trim) is 1 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 2830
8 Falls 10 Falls 12 Falls Auxiliary.
Working Spring Fixed Spring Fixed Spring Fixed Spring Fixed
Radius Constant Dynamic Constant Dynamic Constant Dynamic Constant Dynamic
(feet) (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef.
40 257 1.1 308 1.1 355 1.1 31 1.1
50 239 1.1 282 1.1 321 1.1 31 1.1
60 221 1.1 257 1.1 289 1.1 31 1.1
70 205 1.1 235 1.1 260 1.1 31 1.1
80 189 1.1 213 1.1 234 1.1 31 1.1
90 174 1.1 194 1.1 211 1.1 30 1.1
100 159 1.1 176 1.1 189 1.1 30 1.1
110 145 1.1 159 1.1 169 1.1 30 1.1
120 132 1.1 143 1.1 151 1.1 30 1.1
130 119 1.1 128 1.1 134 1.1 30 1.1
140 107 1.1 113 1.1 118 1.1 29 1.1
150 95 1.1 100 1.1 103 1.1 29 1.1
160 83 1.1 86 1.1 89 1.1 28 1.1
170 71 1.1 73 1.1 75 1.1 27 1.1
180 58 1.1 59 1.1 60 1.1 26 1.1
188 41 1.1 42 1.1 43 1.1 24 1.1

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 0
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469
4456 Project Identification: JASCON2830
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 22.00 Drum Width Between Flanges (in) 44
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

08-07-2006
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 2830
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 30.00 Drum Width Between Flanges (in) 69
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance- 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 496,448 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29

Main Drum Performance - 10 Part Line

Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 560,776 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22

Main Drum Performance - 12 Part Line

Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 08-07-2006
Seatrax Crane Data Sheet
ASME B30.8 / ABS Heavy Lift Safe Working Load Chart
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 2.5 deg. The Specified Offlead Angle (Trim) is 1 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469
4456 Project Identification: JASCON 28
30
Working 8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 593301a 55279d
50 409063c 506122c 549226e 55279d
60 409063c 464263e 464263e 55279d
70 402024e 402024e 402024e 55279d
80 353678e 353678e 353678e 55279d
90 314421e 314421e 314421e 55279d
100 281420e 281420e 281420e 55279d
110 252883e 252883e 252883e 55279d
120 227606e 227606e 227606e 55279d
130 204728e 204728e 204728e 55279d
140 183579e 183579e 183579e 55279d
150 163575e 163575e 163575e 55279d
160 144098e 144098e 144098e 55279d
170 124260e 124260e 124260e 55279d
180 101965e 101965e 101965e 55279d
188 71440e 71440e 71440e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 2.5 deg.
(8) The Specified Offlead Angle (Trim) is 1 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

In Compliance with
ASME B30.8 / ABS Heavy Lift

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4469

The Specified Sidelead Angle (List) is 3.5 deg.

The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469
Project Identification: JASCON 28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 21.5
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction 6X31
Min. Breaking Strength of Boom Hoist Cable (kips) 202
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

ASME B30.8 / ABS Heavy Lift
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet

ASME B30.8 / ABS Heavy Lift Safe Working Load Chart

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Working
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 521946a 55279d
50 409063c 506122c 506959a 55279d
60 409063c 493003a 493003a 55279d
70 409063c 427679e 427679e 55279d
80 372968e 372968e 372968e 55279d
90 329334e 329334e 329334e 55279d
100 293161e 293161e 293161e 55279d
110 262230e 262230e 262230e 55279d
120 235084e 235084e 235084e 55279d
130 210705e 210705e 210705e 55279d
140 188318e 188318e 188318e 55279d
150 167266e 167266e 167266e 55279d
160 146875e 146875e 146875e 55279d
170 126204e 126204e 126204e 55279d
180 103080e 103080e 103080e 55279d
188 71581e 71581e 71581e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 3.5 deg.
(8) The Specified Offlead Angle (Trim) is 0 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Kingpost Reactions - ASME B30.8/ ABS Heavy Lift
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Working Safe Working Vertical Primary Sideplane Torsional
Radius Load Load Moment Moment Moment
(feet) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 521,946 1,081 26,583 10,872 2,395
50 506,959 1,065 32,538 10,483 2,918
60 493,003 1,049 38,233 10,084 3,417
70 427,679 978 39,664 8,755 3,525
80 372,968 917 40,592 7,622 3,587
90 329,334 869 41,414 6,688 3,640
100 293,161 830 42,095 5,886 3,679
110 262,230 796 42,616 5,175 3,703
120 235,084 766 42,955 4,530 3,711
130 210,705 739 43,093 3,929 3,701
140 188,318 714 43,002 3,360 3,669
150 167,266 691 42,638 2,808 3,613
160 146,875 669 41,927 2,258 3,524
170 126,204 646 40,715 1,689 3,390
180 103,080 620 38,563 1,046 3,169
188 71,581 586 33,757 203 2,710

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(3) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(4) The Primary Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(5) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(6) The Total Vertical Load is the summation, in KIPS, with 1.1 times SWL + dead loads.
(7) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet

Cv and Spring Constants

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg.
The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
8 Falls 10 Falls 12 Falls Auxiliary.
Working Spring Fixed Spring Fixed Spring Fixed Spring Fixed
Radius Constant Dynamic Constant Dynamic Constant Dynamic Constant Dynamic
(feet) (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef.
40 262 1.1 315 1.1 364 1.1 31 1.1
50 243 1.1 288 1.1 329 1.1 31 1.1
60 225 1.1 263 1.1 296 1.1 31 1.1
70 208 1.1 239 1.1 266 1.1 31 1.1
80 192 1.1 218 1.1 240 1.1 31 1.1
90 177 1.1 198 1.1 215 1.1 31 1.1
100 162 1.1 179 1.1 193 1.1 30 1.1
110 148 1.1 161 1.1 172 1.1 30 1.1
120 134 1.1 145 1.1 154 1.1 30 1.1
130 121 1.1 129 1.1 136 1.1 30 1.1
140 108 1.1 115 1.1 120 1.1 29 1.1
150 96 1.1 101 1.1 105 1.1 29 1.1
160 84 1.1 87 1.1 90 1.1 28 1.1
170 72 1.1 74 1.1 76 1.1 28 1.1
180 58 1.1 59 1.1 61 1.1 26 1.1
188 42 1.1 42 1.1 43 1.1 24 1.1

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 0
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 22.00 Drum Width Between Flanges (in) 44
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 30.00 Drum Width Between Flanges (in) 69
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance- 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 496,448 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29

Main Drum Performance - 10 Part Line

Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 560,776 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22

Main Drum Performance - 12 Part Line

Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 09-21-2007
Seatrax Crane Data Sheet
ASME B30.8 / ABS Heavy Lift Safe Working Load Chart
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg. The Specified Offlead Angle (Trim) is 0 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Working 8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 506122c 521946a 55279d
50 409063c 506122c 506959a 55279d
60 409063c 493003a 493003a 55279d
70 409063c 427679e 427679e 55279d
80 372968e 372968e 372968e 55279d
90 329334e 329334e 329334e 55279d
100 293161e 293161e 293161e 55279d
110 262230e 262230e 262230e 55279d
120 235084e 235084e 235084e 55279d
130 210705e 210705e 210705e 55279d
140 188318e 188318e 188318e 55279d
150 167266e 167266e 167266e 55279d
160 146875e 146875e 146875e 55279d
170 126204e 126204e 126204e 55279d
180 103080e 103080e 103080e 55279d
188 71581e 71581e 71581e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 3.5 deg.
(8) The Specified Offlead Angle (Trim) is 0 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

In Compliance with
ASME B30.8 / ABS Heavy Lift

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4469

The Specified Sidelead Angle (List) is 3.5 deg.

The Specified Offlead Angle (Trim) is 3.5 deg.
Windspeed = 10 knots
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469
Project Identification: JASCON 28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 21.5
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction 6X31
Min. Breaking Strength of Boom Hoist Cable (kips) 202
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

ASME B30.8 / ABS Heavy Lift
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet

ASME B30.8 / ABS Heavy Lift Safe Working Load Chart

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg.
The Specified Offlead Angle (Trim) is 3.5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Working
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 472559a 472559a 55279d
50 409063c 446270e 446270e 55279d
60 391517e 391517e 391517e 55279d
70 347930e 347930e 347930e 55279d
80 312081e 312081e 312081e 55279d
90 281712e 281712e 281712e 55279d
100 255326e 255326e 255326e 55279d
110 231893e 231893e 231893e 55279d
120 210676e 210676e 210676e 55279d
130 191111e 191111e 191111e 55279d
140 172735e 172735e 172735e 55279d
150 155110e 155110e 155110e 55279d
160 137734e 137734e 137734e 55279d
170 119834e 119834e 119834e 55279d
180 99494e 99494e 99494e 55279d
188 71315e 71315e 71315e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 3.5 deg.
(8) The Specified Offlead Angle (Trim) is 3.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Kingpost Reactions - ASME B30.8/ ABS Heavy Lift
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg.
The Specified Offlead Angle (Trim) is 3.5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Working Safe Working Vertical Primary Sideplane Torsional
Radius Load Load Moment Moment Moment
(feet) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 472,559 1,027 34,327 9,967 2,196
50 446,270 998 38,535 9,383 2,612
60 391,517 938 39,759 8,271 2,803
70 347,930 890 40,836 7,356 2,962
80 312,081 850 41,770 6,577 3,096
90 281,712 817 42,552 5,893 3,207
100 255,326 788 43,171 5,275 3,297
110 231,893 762 43,615 4,705 3,367
120 210,676 739 43,869 4,169 3,416
130 191,111 717 43,917 3,657 3,444
140 172,735 697 43,732 3,158 3,449
150 155,110 678 43,272 2,665 3,429
160 137,734 659 42,460 2,163 3,377
170 119,834 639 41,141 1,634 3,281
180 99,494 617 38,866 1,025 3,104
188 71,315 586 33,902 202 2,705

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(3) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(4) The Primary Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(5) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(6) The Total Vertical Load is the summation, in KIPS, with 1.1 times SWL + dead loads.
(7) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet

Cv and Spring Constants

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg.
The Specified Offlead Angle (Trim) is 3.5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
8 Falls 10 Falls 12 Falls Auxiliary.
Working Spring Fixed Spring Fixed Spring Fixed Spring Fixed
Radius Constant Dynamic Constant Dynamic Constant Dynamic Constant Dynamic
(feet) (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef.
40 246 1.1 292 1.1 335 1.1 31 1.1
50 229 1.1 268 1.1 303 1.1 31 1.1
60 212 1.1 245 1.1 273 1.1 31 1.1
70 196 1.1 223 1.1 247 1.1 31 1.1
80 181 1.1 204 1.1 223 1.1 30 1.1
90 167 1.1 185 1.1 201 1.1 30 1.1
100 153 1.1 168 1.1 181 1.1 30 1.1
110 140 1.1 153 1.1 162 1.1 30 1.1
120 128 1.1 138 1.1 145 1.1 30 1.1
130 116 1.1 123 1.1 130 1.1 29 1.1
140 104 1.1 110 1.1 115 1.1 29 1.1
150 93 1.1 97 1.1 101 1.1 29 1.1
160 81 1.1 84 1.1 87 1.1 28 1.1
170 70 1.1 72 1.1 74 1.1 27 1.1
180 57 1.1 59 1.1 60 1.1 26 1.1
188 41 1.1 42 1.1 43 1.1 24 1.1

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 0
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 22.00 Drum Width Between Flanges (in) 44
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 30.00 Drum Width Between Flanges (in) 69
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance- 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 496,448 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29

Main Drum Performance - 10 Part Line

Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 560,776 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22

Main Drum Performance - 12 Part Line

Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 09-21-2007
Seatrax Crane Data Sheet
ASME B30.8 / ABS Heavy Lift Safe Working Load Chart
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 3.5 deg. The Specified Offlead Angle (Trim) is 3.5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Working 8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 409063c 472559a 472559a 55279d
50 409063c 446270e 446270e 55279d
60 391517e 391517e 391517e 55279d
70 347930e 347930e 347930e 55279d
80 312081e 312081e 312081e 55279d
90 281712e 281712e 281712e 55279d
100 255326e 255326e 255326e 55279d
110 231893e 231893e 231893e 55279d
120 210676e 210676e 210676e 55279d
130 191111e 191111e 191111e 55279d
140 172735e 172735e 172735e 55279d
150 155110e 155110e 155110e 55279d
160 137734e 137734e 137734e 55279d
170 119834e 119834e 119834e 55279d
180 99494e 99494e 99494e 55279d
188 71315e 71315e 71315e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 3.5 deg.
(8) The Specified Offlead Angle (Trim) is 3.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007

Seatrax Inc.
P.O. Box 840687 Houston, Texas 77284
Telephone (713) 896-6500
Fax (713) 896-6611

Seatrax Crane Data Sheet

In Compliance with
ASME B30.8 / ABS Heavy Lift

Imperial Units
Seatrax Series 115 Model 11532HD
180 Foot Boom

Prepared For
SEATRUCKS
JASCON 28
KINGPOST MARINE CRANE
SEATRAX QUOTATION No. 602116
SEATRAX SERIAL No. 4469

The Specified Sidelead Angle (List) is 5 deg.

The Specified Offlead Angle (Trim) is 5 deg.
Windspeed = 10 knots
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Seatrax Series 115 Model 11532HD
180 Foot Boom
Serial or Quotation Number: 4469
Project Identification: JASCON 28
GENERAL CRANE DIMENSIONS
Vertical Dim Heel Pin to Gantry Sheave 'H' (ft) 58.00
Horizontal Dim CL Rot to Heel Pin 'E' (ft) 8.00
Horizontal Dim CL Rot to Gantry Sheave 'D' (ft) 16.00
Horizontal Dim CL Rot to CG of Crane & Post 'U' (ft) 4.00
Outside Diameter of Kingpost 'OD' (in) 115.00
Wall Thickness of Kingpost 'T' (in) 2.50
Yield Strength of Kingpost 'YP' (ksi) 50.00
Vertical Dim Lower Brg to Upper Brg 'GB' (ft) 36.00
COMPONENT STATIC WEIGHTS (kips)
Complete Crane with Boom (Kips) 485.6
Block(s) (kips) 21.5
Total Dead Weight (Kips) 507.1
WIRE ROPE COMPONENT DATA
Length of the Aux. Hoist Cable (ft.) 500
Diameter of Aux. Hoist Cable (in.) 1.5
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (kips) 291
Length of Main Hoist Cable (ft.) 3250
Diameter of Main Hoist Cable (in.) 1.25
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (kips) 205
Diameter of Boom Hoist Cable (in.) 1.375
Boom Hoist Cable Construction 6X31
Min. Breaking Strength of Boom Hoist Cable (kips) 202
Number of Boom Suspension Parts of Line 'NB' 12
PROPERTIES OF BOOM SECTION
Boom Chord Square Tube Size @ Butt 'BTS1' (in) 10.00
Height Between Chord Centers @ Mid 'HB2' (in) 94
Width Between Chord Centers @ Mid 'WB2' (in) 141
HOIST SELECTIONS
Auxiliary Hoist Model Number M1000E15
Main Hoist Model Number L1000E-2

This crane complies with all applicable requirements of

ASME B30.8 / ABS Heavy Lift
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet

ASME B30.8 / ABS Heavy Lift Safe Working Load Chart

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 5 deg.
The Specified Offlead Angle (Trim) is 5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Working
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 374311a 374311a 374311a 55279d
50 374291a 374291a 374291a 55279d
60 356339e 356339e 356339e 55279d
70 320948e 320948e 320948e 55279d
80 290852e 290852e 290852e 55279d
90 264725e 264725e 264725e 55279d
100 241087is 241087is 241087is 55279d
110 212646is 212646is 212646is 55279d
120 188557is 188557is 188557is 55279d
130 168298is 168298is 168298is 55279d
140 150930is 150930is 150930is 55279d
150 135694is 135694is 135694is 55279d
160 122419is 122419is 122419is 55279d
170 110742is 110742is 110742is 55279d
180 98221e 98221e 98221e 55279d
188 71396e 71396e 71396e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 5 deg.
(8) The Specified Offlead Angle (Trim) is 5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Kingpost Reactions - ASME B30.8/ ABS Heavy Lift
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 5 deg.
The Specified Offlead Angle (Trim) is 5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Working Safe Working Vertical Primary Sideplane Torsional
Radius Load Load Moment Moment Moment
(feet) (Pounds) (Kips) (Kip-Ft.) (Kip-Ft.) (Kip-Ft.)
40 374,311 919 31,682 11,668 2,570
50 374,291 919 36,711 11,541 3,213
60 356,339 899 40,061 10,918 3,700
70 320,948 860 41,213 9,832 3,959
80 290,852 827 42,180 8,875 4,177
90 264,725 798 42,972 8,011 4,360
100 241,087 772 43,519 7,204 4,503
110 212,646 741 42,859 6,291 4,502
120 188,557 715 42,254 5,484 4,494
130 168,298 692 41,755 4,765 4,488
140 150,930 673 41,313 4,104 4,482
150 135,694 656 40,873 3,476 4,472
160 122,419 642 40,456 2,860 4,464
170 110,742 629 40,023 2,220 4,469
180 98,221 615 39,037 1,451 4,393
188 71,396 586 34,005 289 3,857

(1) Working Radius is measured from the center of the main hook to the center of rotation
(2) The Primary Moment is the summation of moments about an axis 90 degrees to the boom centerline
(3) The Side Plane (Radial) Moment is the summation of moments about an axis parallel to the boom centerline.
(4) The Primary Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(5) The Side Plane (Radial) Moment is the overturning moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
(6) The Total Vertical Load is the summation, in KIPS, with 1.1 times SWL + dead loads.
(7) The Torsional Moment (Torque) is the rotational moment in KIP-FEET, with 1.1 times SWL & Resulting Horizontal Loads + dead loads.
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet

Cv and Spring Constants

Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 5 deg.
The Specified Offlead Angle (Trim) is 5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
8 Falls 10 Falls 12 Falls Auxiliary.
Working Spring Fixed Spring Fixed Spring Fixed Spring Fixed
Radius Constant Dynamic Constant Dynamic Constant Dynamic Constant Dynamic
(feet) (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef. (Kip/Ft) Coef.
40 240 1.1 284 1.1 323 1.1 31 1.1
50 223 1.1 260 1.1 293 1.1 31 1.1
60 207 1.1 238 1.1 265 1.1 31 1.1
70 191 1.1 217 1.1 239 1.1 30 1.1
80 177 1.1 198 1.1 216 1.1 30 1.1
90 163 1.1 181 1.1 195 1.1 30 1.1
100 150 1.1 164 1.1 176 1.1 30 1.1
110 137 1.1 149 1.1 159 1.1 30 1.1
120 125 1.1 135 1.1 142 1.1 29 1.1
130 114 1.1 121 1.1 127 1.1 29 1.1
140 102 1.1 108 1.1 113 1.1 29 1.1
150 91 1.1 96 1.1 99 1.1 28 1.1
160 80 1.1 83 1.1 86 1.1 28 1.1
170 69 1.1 71 1.1 73 1.1 27 1.1
180 57 1.1 58 1.1 59 1.1 26 1.1
188 41 1.1 42 1.1 43 1.1 24 1.1

(1) All Spiring Constants are in kips/ft.

(2) The calculated Supply Boat Deck Velocity in ft/sec is 0
(3) The avaliable 1 Fall Hook Speed in ft/sec is 4.57
(4) The available 2 Fall Hook Speed in ft/sec is 2.32
(5) The available 4 Fall Hook Speed in ft/sec is 1.08
(6) The available 6 Fall Hook Speed in ft/sec is .68
(7) The available 8 Fall Hook Speed in ft/sec is .47
(8) The available 10 Fall Hook Speed in ft/sec is .35
(9) The available 12 Fall Hook Speed in ft/sec is .27
(10) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(11) The Specified Lateral Acceleration caused by Foundation Motions is 0
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Auxiliary Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model M1000E15
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 22.00 Drum Width Between Flanges (in) 44
Motor Torque (in-lbs) 15,406 Drum Torque (in-lbs) 871,565
Motor Speed (rpm) 2,268 Drum Speed (rpm) 38
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/2
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 63,386 274 209
2 57,915 300 429
3 53,313 326 678
4 49,388 352 936
5 46,002 378 1,224
6 43,050 404 1,521

Auxiliary Drum Performance

Hook Load @ Boom Tip 56,779 Hook Speed @ Boom Tip 300
Hook Load @ Deck 56,779 Hook Speed @ Deck 300
Hook Load @ Water 62,143 Hook Speed @ Water 274
 P.O. Box 840687, Houston, Texas 77284
Phone: 713 896 6500 Fax: 713 896 6611

09-21-2007
Seatrax Crane Data Sheet
Main Drum Performance
Seatrax Drilling-Duty Hoist Configuration
Seatrax Series 115 Model 11532HD
180 Foot Boom
Hoist Model L1000E-2
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Pressure (psi) 5,000 Drum Barrel Diameter (in) 26
Flow (gpm) 225 Drum Flange Diameter (in) 52
Motor Displacement (in 3 /rev) 30.00 Drum Width Between Flanges (in) 69
Motor Torque (in-lbs) 21,008 Drum Torque (in-lbs) 1,188,497
Motor Speed (rpm) 1,663 Drum Speed (rpm) 28
Gear Reduction 59.54 Diameter of Aux Cable (in) 1 1/4
This Seatrax Drilling-Duty Hoist is Equipped with an External Contracting Drum Band Brake

Installation Dimensions
Boom Pivot Height Above Deck Level (ft.) 58
Deck Level to Lowest Hook Position ie. water level (ft.) 13
The Maximum Req'd Hook Travel for This Crane is 251

Single Line Performance

Layer Line Line Cumulative
of Pull Speed Cable
Cable (lbs.) (fpm) Capacity
1 87,229 199 392
2 80,808 215 808
3 75,269 231 1,263
4 70,439 247 1,740
5 66,193 263 2,257
6 62,429 278 2,795
7 59,070 294 3,375
8 56,054 310 3,974

Main Drum Performance- 8 Part Line

Hook Load @ Boom Tip 443,028 Hook Speed @ Boom Tip 37
Hook Load @ Deck 496,448 Hook Speed @ Deck 35
Hook Load @ Water 564,517 Hook Speed @ Water 29

Main Drum Performance - 10 Part Line

Hook Load @ Boom Tip 530,605 Hook Speed @ Boom Tip 29
Hook Load @ Deck 560,776 Hook Speed @ Deck 28
Hook Load @ Water 725,873 Hook Speed @ Water 22

Main Drum Performance - 12 Part Line

Hook Load @ Boom Tip 624,690 Hook Speed @ Boom Tip 25
Hook Load @ Deck 700,015 Hook Speed @ Deck 22
Hook Load @ Water 922,478 Hook Speed @ Water 17
 09-21-2007
Seatrax Crane Data Sheet
ASME B30.8 / ABS Heavy Lift Safe Working Load Chart
Seatrax Series 115 Model 11532HD
180 Foot Boom
The Specified Sidelead Angle (List) is 5 deg. The Specified Offlead Angle (Trim) is 5 deg.
Windspeed = 10 knots
Serial or Quotation Number: 4469 Project Identification: JASCON 28
Working 8 Part Main Block 10 Part Main Block 12 Part Main Block 1 Part Aux Block
Radius Safe Working Load Safe Working Load Safe Working Load Safe Working Load
(Feet) (Pounds) (Pounds) (Pounds) (Pounds)
40 374311a 374311a 374311a 55279d
50 374291a 374291a 374291a 55279d
60 356339e 356339e 356339e 55279d
70 320948e 320948e 320948e 55279d
80 290852e 290852e 290852e 55279d
90 264725e 264725e 264725e 55279d
100 241087is 241087is 241087is 55279d
110 212646is 212646is 212646is 55279d
120 188557is 188557is 188557is 55279d
130 168298is 168298is 168298is 55279d
140 150930is 150930is 150930is 55279d
150 135694is 135694is 135694is 55279d
160 122419is 122419is 122419is 55279d
170 110742is 110742is 110742is 55279d
180 98221e 98221e 98221e 55279d
188 71396e 71396e 71396e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) Small Letter Suffixes Indicate Limiting Load Factors
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 0
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1g.
(7) The Specified Sidelead Angle (List) is 5 deg.
(8) The Specified Offlead Angle (Trim) is 5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

ONBOARD (DECK) LIFTS

Seatrax Series 115 Model 11532HD 180 Foot Boom
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
(feet) SWL (Lbs) SWL (Lbs) SWL (Lbs) SWL (Lbs)
40 308000c 390000c 466141a 55279d
50 308000c 390000c 433175e 55279d
60 308000c 372993e 372993e 55279d
70 308000c 324350a 324350a 55279d
80 283606a 283606a 283606a 55279d
90 251497a 251497a 251497a 55279d
100 225182a 225182a 225182a 55279d
110 203653a 203653a 203653a 55279d
120 185200b 185200b 185200b 55279d
130 167972e 167972e 167972e 55279d
140 150014e 150014e 150014e 55279d
150 132884e 132884e 132884e 55279d
160 116078e 116078e 116078e 55279d
170 98843e 98843e 98843e 55279d
180 79342e 79342e 79342e 55279d
188 52449e 52449e 52449e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

OFFBOARD (SUPPLY BOAT) LIFTS

Seatrax Series 115 Model 11532HD 180 Foot Boom
Significant Wave Height = 1 feet (Seastate 1-2) Windspeed = 10 knots
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
(feet) SWL (Lbs) SWL (Lbs) SWL (Lbs) SWL (Lbs)
40 308000c 373334a 373334a 55279d
50 308000c 343312e 343312e 55279d
60 306334e 306334e 306334e 55279d
70 274967e 274967e 274967e 55279d
80 247171a 247171a 247171a 55279d
90 221655a 221655a 221655a 55279d
100 200824a 200824a 200824a 55279d
110 183174a 183174a 183174a 55279d
120 167240e 167240e 167240e 55279d
130 150974e 150974e 150974e 55279d
140 135542e 135542e 135542e 55279d
150 120633e 120633e 120633e 55279d
160 105884e 105884e 105884e 55279d
170 90755e 90755e 90755e 55279d
180 74127e 74127e 74127e 55279d
188 51952is 51952is 51952is 51952is

(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 5E-002 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 2.9E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

INFORMATION CHART
Seatrax Series 115 Model 11532HD 180 Foot Boom
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28

Seatrax Kingpost Marine Crane Operating Notes:

1.) This is a Seatrax Kingpost Marine Crane. Unlike Conventional Cranes, It CANNOT
Separate from its Foundation (Pedestal) Due to Slew Bearing Failure.

2.) This Seatrax Kingpost Marine Crane has Fail-Safe Hoists. Releasing the Controls Sets
all Hoist Brakes Automatically. If a Load Slips Downward, Do NOT Pull Back on the
Controls as this Action Signals the Brakes to Remain Off. RELEASE the Controls to Set
Brakes.

3.) This Seatrax Kingpost Marine Crane is Equipped with a Patented Mechanical Two Block
System. Lowering the Boom will NOT cause it to Contact the Hook Blocks.

4.) For Optimum Safety and Service Life, Follow the Operating, Inspection and Maintenance
Instructions in the Seatrax Operation and Maintence Manual or CD.

Wire Rope Component Data

Length of the Aux. Hoist Cable (feet) 500
Diameter of Aux. Hoist Cable (inch) 1 1/2
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (Kips) 291

Length of Main Hoist Cable (feet) 3,250

Diameter of Main Hoist Cable (inch) 1 1/4
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (Kips) 205

Diameter of Boom Hoist Cable (inch) 1 3/8

Boom Hoist Cable Construction QS816V/PZ371
Min. Breaking Strength of Boom Hoist Cable (Kips) 235
Boom Hoist Cable Parts of Line 12

Additional Data
1.) The Main and Auxiliary Hook Travel for This Machine in Feet: 251
2.) Seatrax Load Charts Indicate Nominal Minimum and Maximum Working Radii
3.) Maximum Auxiliary Hook Speed @ Water Level in Feet/Minute: 274
4.) Maximum 8 Part Main Hook Speed @ Water Level-Feet/Minute: 29
Maximum 10 Part Main Hook Speed @ Water Level-Feet/Minute: 22
Maximum 12 Part Main Hook Speed @ Water Level-Feet/Minute: 17
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

ONBOARD (DECK) LIFTS

Seatrax Series 115 Model 11532HD 180 Foot Boom
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
(feet) SWL (Lbs) SWL (Lbs) SWL (Lbs) SWL (Lbs)
40 308000c 390000c 455557a 55279d
50 308000c 390000c 433175e 55279d
60 308000c 372993e 372993e 55279d
70 308000c 324350a 324350a 55279d
80 283606a 283606a 283606a 55279d
90 251497a 251497a 251497a 55279d
100 225182a 225182a 225182a 55279d
110 203653a 203653a 203653a 55279d
120 185200b 185200b 185200b 55279d
130 167972e 167972e 167972e 55279d
140 150014e 150014e 150014e 55279d
150 132884e 132884e 132884e 55279d
160 116078e 116078e 116078e 55279d
170 98843e 98843e 98843e 55279d
180 79342e 79342e 79342e 55279d
188 52449e 52449e 52449e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

OFFBOARD (SUPPLY BOAT) LIFTS

Seatrax Series 115 Model 11532HD 180 Foot Boom
Significant Wave Height = 2.9 feet (Seastate 2-3) Windspeed = 15 knots
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
(feet) SWL (Lbs) SWL (Lbs) SWL (Lbs) SWL (Lbs)
40 308000c 344102a 344102a 55279d
50 308000c 322342e 322342e 55279d
60 290257e 290257e 290257e 55279d
70 262215e 262215e 262215e 55279d
80 237690e 237690e 237690e 55279d
90 214276a 214276a 214276a 55279d
100 194552a 194552a 194552a 55279d
110 177799a 177799a 177799a 55279d
120 162087e 162087e 162087e 55279d
130 146593e 146593e 146593e 55279d
140 131833e 131833e 131833e 55279d
150 117534e 117534e 117534e 55279d
160 103377e 103377e 103377e 55279d
170 88906e 88906e 88906e 55279d
180 73330e 73330e 73330e 55279d
188 40333is 40333is 40333is 40333is

(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is .42 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 3.2E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

INFORMATION CHART
Seatrax Series 115 Model 11532HD 180 Foot Boom
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28

Seatrax Kingpost Marine Crane Operating Notes:

1.) This is a Seatrax Kingpost Marine Crane. Unlike Conventional Cranes, It CANNOT
Separate from its Foundation (Pedestal) Due to Slew Bearing Failure.

2.) This Seatrax Kingpost Marine Crane has Fail-Safe Hoists. Releasing the Controls Sets
all Hoist Brakes Automatically. If a Load Slips Downward, Do NOT Pull Back on the
Controls as this Action Signals the Brakes to Remain Off. RELEASE the Controls to Set
Brakes.

3.) This Seatrax Kingpost Marine Crane is Equipped with a Patented Mechanical Two Block
System. Lowering the Boom will NOT cause it to Contact the Hook Blocks.

4.) For Optimum Safety and Service Life, Follow the Operating, Inspection and Maintenance
Instructions in the Seatrax Operation and Maintence Manual or CD.

Wire Rope Component Data

Length of the Aux. Hoist Cable (feet) 500
Diameter of Aux. Hoist Cable (inch) 1 1/2
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (Kips) 291

Length of Main Hoist Cable (feet) 3,250

Diameter of Main Hoist Cable (inch) 1 1/4
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (Kips) 205

Diameter of Boom Hoist Cable (inch) 1 3/8

Boom Hoist Cable Construction QS816V/PZ371
Min. Breaking Strength of Boom Hoist Cable (Kips) 235
Boom Hoist Cable Parts of Line 12

Additional Data
1.) The Main and Auxiliary Hook Travel for This Machine in Feet: 251
2.) Seatrax Load Charts Indicate Nominal Minimum and Maximum Working Radii
3.) Maximum Auxiliary Hook Speed @ Water Level in Feet/Minute: 274
4.) Maximum 8 Part Main Hook Speed @ Water Level-Feet/Minute: 29
Maximum 10 Part Main Hook Speed @ Water Level-Feet/Minute: 22
Maximum 12 Part Main Hook Speed @ Water Level-Feet/Minute: 17
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

ONBOARD (DECK) LIFTS

Seatrax Series 115 Model 11532HD 180 Foot Boom
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
(feet) SWL (Lbs) SWL (Lbs) SWL (Lbs) SWL (Lbs)
40 302561a 302561a 302561a 55279d
50 298825a 298825a 298825a 55279d
60 293688a 293688a 293688a 55279d
70 288621a 288621a 288621a 55279d
80 283606a 283606a 283606a 55279d
90 251497a 251497a 251497a 55279d
100 225182a 225182a 225182a 55279d
110 198888is 198888is 198888is 55279d
120 174270is 174270is 174270is 55279d
130 153322is 153322is 153322is 55279d
140 135425is 135425is 135425is 55279d
150 119797is 119797is 119797is 55279d
160 106211is 106211is 106211is 55279d
170 94253is 94253is 94253is 55279d
180 79342e 79342e 79342e 55279d
188 52449e 52449e 52449e 55279d

(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is N/A.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

OFFBOARD (SUPPLY BOAT) LIFTS

Seatrax Series 115 Model 11532HD 180 Foot Boom
Significant Wave Height = 6.9 feet (Seastate 4-5) Windspeed = 20 knots
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28
Working 8 Part 10 Part Line 12 Part Single Line
Radius Main Hoist Main Hoist Main Hoist Aux Hoist
(feet) SWL (Lbs) SWL (Lbs) SWL (Lbs) SWL (Lbs)
40 152640a 147415a 140017a 49204c
50 159873a 155158a 148654a 49323c
60 164068a 159923a 154348a 49441c
70 166726a 163153a 158465a 49556c
80 155043a 152183a 148490a 49670c
90 139539a 137341a 134545a 49785c
100 126547a 124896a 122833a 49906c
110 116201a 115001a 113536a 50036c
120 107684a 106861a 105890a 50182c
130 100998a 100491a 99930a 50351c
140 95843a 95606a 95385a 50554c
150 87119is 87119is 87119is 50805c
160 73765is 73765is 73765is 51129c
170 60509is 60509is 60509is 51567c
180 45263is 45263is 45263is 45263is
188 N/A N/A N/A 13287ih

(1) Working radius is measured from the main hook to centerline of rotation
(2) SWL letter suffiixes indicate load limiting factor per API 2C, 4.1.1 (a) thru (i).
(3) Rated loads are NET loads. Main Block & Aux. Ball weights have been deducted.
(4) The Specified Boom Tip Velocity caused by Foundation Motions is 2.38 ft./sec.
(5) The Specified Lateral Acceleration caused by Foundation Motions is 8.3E-002
(6) The Specified Vertical Acceleration caused by Foundation Motions is 1.07g.
(7) The Specified Additional Sidelead Angle (List) from Foundation Motions is 1 deg.
(8) The Specified Additional Offlead Angle (Trim) from Foundation Motions is 2.5 deg.
(9) Main drum cable is 1.25 dia. TK16S/D1315, 205 kip. nom strength, 3250 feet long.
(10) Aux. drum cable is 1.5 dia. TK16S/D1315, 291 kip. nom strength, 500 feet long.
(11) The specified hook travel for this machine is 251 feet.
 09-25-2007
Seatrax Crane Data Sheet
(In Compliance with API Specification 2C, 6th Edition, 2004)

INFORMATION CHART
Seatrax Series 115 Model 11532HD 180 Foot Boom
Drillship API General Method
Serial or Quotation Number: 4469A Project Identification: JASCON 28

Seatrax Kingpost Marine Crane Operating Notes:

1.) This is a Seatrax Kingpost Marine Crane. Unlike Conventional Cranes, It CANNOT
Separate from its Foundation (Pedestal) Due to Slew Bearing Failure.

2.) This Seatrax Kingpost Marine Crane has Fail-Safe Hoists. Releasing the Controls Sets
all Hoist Brakes Automatically. If a Load Slips Downward, Do NOT Pull Back on the
Controls as this Action Signals the Brakes to Remain Off. RELEASE the Controls to Set
Brakes.

3.) This Seatrax Kingpost Marine Crane is Equipped with a Patented Mechanical Two Block
System. Lowering the Boom will NOT cause it to Contact the Hook Blocks.

4.) For Optimum Safety and Service Life, Follow the Operating, Inspection and Maintenance
Instructions in the Seatrax Operation and Maintence Manual or CD.

Wire Rope Component Data

Length of the Aux. Hoist Cable (feet) 500
Diameter of Aux. Hoist Cable (inch) 1 1/2
Aux. Hoist Cable Construction TK16S/D1315
Minimum Breaking Strength of Aux. Cable (Kips) 291

Length of Main Hoist Cable (feet) 3,250

Diameter of Main Hoist Cable (inch) 1 1/4
Main Hoist Cable Construction TK16S/D1315
Min. Breaking Strength of Main Hoist Cable (Kips) 205

Diameter of Boom Hoist Cable (inch) 1 3/8

Boom Hoist Cable Construction QS816V/PZ371
Min. Breaking Strength of Boom Hoist Cable (Kips) 235
Boom Hoist Cable Parts of Line 12

Additional Data
1.) The Main and Auxiliary Hook Travel for This Machine in Feet: 251
2.) Seatrax Load Charts Indicate Nominal Minimum and Maximum Working Radii
3.) Maximum Auxiliary Hook Speed @ Water Level in Feet/Minute: 274
4.) Maximum 8 Part Main Hook Speed @ Water Level-Feet/Minute: 29
Maximum 10 Part Main Hook Speed @ Water Level-Feet/Minute: 22
Maximum 12 Part Main Hook Speed @ Water Level-Feet/Minute: 17