EcoStruxure™ Building www.schneider-electric.

com/buildings | 1

MP-C
SmartX IP Controller

Introduction • BACnet/IP communications

SmartX IP Controller – MP-C is a multi-purpose, fully • DHCP for easy network configuration
programmable, IP based field controller. The MP-C
models offer a flexible mix of I/O point types that suit a The MP Series controllers have a dual-port Ethernet
wide range of HVAC applications. MP-C can either be switch, which enables flexible network topologies:
used as a standalone BACnet/IP field controller or as
part of an EcoStruxure BMS with a SmartX AS-P or AS- • Star
B server or an Enterprise Server as the parent server.
• Daisy chain
The MP-C models support an optional display that
provides insight and control of the inputs and outputs. • Rapid Spanning Tree Protocol (RSTP) ring

The MP-C has the following features: In a star topology, the controller and the parent
EcoStruxure BMS server are individually connected to
• IP enabled with dual port Ethernet switch an Ethernet switch. You can reduce the installation time
and cost by daisy-chaining multiple controllers
• Versatile onboard I/O point mix together. You can use an RSTP ring topology when you
• High reliability want failures of a single controller to be detected and
recovered quickly and efficiently.
• Sensor bus for living space sensors
• Mobile commissioning application Models with a versatile mix of I/O points
• Full EcoStruxure Building Operation software MP-C comes in five models with different I/O point
support, providing efficient engineering tools count and a versatile mix of I/O point types that match a
wide variety of applications. Most of the I/O points are
IP connectivity and flexible network topologies universal inputs/outputs, which are highly flexible and
can be configured as either inputs or outputs.
The MP Series controllers are based on open protocols
that simplify interoperability, IP configuration, and
device management:

• IP addressing

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 2

MP-C
SmartX IP Controller

I/O Point Types by MP-C Models

I/O Point Types MP-C-15A MP-C-18A MP-C-18B MP-C-24A MP-C-36A

Universal I/O 8 10 10 16 20
Type Ub
Universal I/O - - - 4 8
Type Uc
Triac outputs 6 4 8 - -
Relay outputs - 3 - 4 8
Form A
High power relay 1 1 - - -
outputs
Form A

Configurations by I/O Point Types

Configurations Universal I/O Universal I/O Triac Outputs Relay Outputs High Power Relay
Type Ub Type Uc Form A Outputs
Form A
Digital inputs yes yes - - -
Counter inputs yes yes - - -
Supervised inputs yes yes - - -
Voltage inputs yes yes - - -
(0 to 10 VDC)
Current inputs yes yes - - -
(0 to 20 mA)
Temperature inputs yes yes - - -
Resistive inputs yes yes - - -
2-wire RTD temperature yes yes - - -
inputs
Voltage outputs yes yes - - -
(0 to 10 VDC)
Current outputs - yes - - -
(0 to 20 mA)
Digital outputs - - yes yes yes
Digital pulsed outputs - - yes yes yes

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 3

MP-C
SmartX IP Controller

PWM outputs - - yes yes yes

Tristate outputs - - yes yes -
Tristate pulsed outputs - - yes yes -

Universal inputs/outputs The battery-free power backup of the memory and real-
The universal inputs/outputs are ideal for any mix of time clock prevents data loss and ensures seamless
temperature, pressure, flow, status points, and similar and quick recovery after a power failure.
point types in a building control system.
All MP-C models can be equipped with the MP-C
As counter inputs, the universal inputs/outputs are Display add-on module, which features an LCD display
commonly used in energy metering applications. As and five keys. With this module, you can manually
RTD inputs, they are ideal for temperature points in a override analog and digital outputs for testing,
building control system. As supervised inputs, they are commissioning, and maintenance of equipment
used for security applications where it is critical to know connected to the outputs. The module's dedicated
whether or not a wire has been cut or shorted. These processing power ensures reliable override for
events provide a separate indication of alarms and maintenance applications. The override status is
trouble conditions to the system. readable through EcoStruxure Building Operation
WorkStation and WebStation, enabling precise
For all analog inputs, maximum and minimum levels monitoring and reliable control.
can be defined to automatically detect over-range and
under-range values.

The universal inputs/outputs can also be used as

voltage outputs or current outputs (Uc only), without the
need for external bias resistors. Therefore, the universal
inputs/outputs support a wide range of devices, such
as actuators.

Triac outputs
The triac outputs can be used in many applications to
switch 24 VAC on or off for external loads such as
actuators, relays, or indicators. The triac outputs are MP-C Display
isolated from the controller. Triacs are silent and do not
suffer from relay contact wear. WorkStation allows you to update the firmware of
multiple MP Series controllers at the same time and with
Relay outputs minimum down time. The EcoStruxure BMS server
The relay outputs support digital Form A point types. keeps track of the installed firmware to support backup,
The Form A relays are designed for direct load restore, and replacement of the controllers and
applications. sensors. The server can host controllers of different
firmware versions.
High power relay output
MP-C-15A and MP-C-18A have a high power relay
Sensor bus for living space sensors
output, which is ideal for switching loads of up to 12 A, The MP Series controllers provide an interface
such as electrical heating elements. designed for the SmartX Sensor family of living space
sensors. The SmartX Sensors offer an efficient way to
High reliability sense the temperature, humidity, CO2, and occupancy
in a room. The SmartX Sensors are available with
The MP Series controllers support local trends, different combinations of sensor types and various
schedules, and alarms, enabling local operation when covers and user interface options, such as
the controller is offline or used in standalone touchscreen, setpoint and override buttons, and blank
applications. covers.

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 4

MP-C
SmartX IP Controller

SmartX Sensors

The sensor bus provides both power and

communications for up to four sensors that are daisy-
chained using standard Cat 5 (or higher) cables. The
maximum number of sensors that can be connected to
a controller varies depending on the sensor model and
the combination of cover and sensor base type: eCommission SmartX Controllers mobile app

• Blank covers: Up to four sensors of any Using the eCommission SmartX Controllers mobile
combination of sensor base types application, you can connect to one or many MP Series
controllers. You can connect to a single MP Series
• 3-button and touchscreen covers: controller using the eCommission Bluetooth Adapter
– Up to two sensor bases with CO2 option connected to a SmartX Sensor. You can connect to a
network of MP Series controllers on the local IP
– Up to four sensor bases without CO2 option network, using a wireless access point or a network
switch.
• SmartX LCD temperature sensors: Up to four
sensors are supported Device configuration
With the eCommission SmartX Controllers mobile
The maximum total length of the sensor bus is 61 m
application, you can easily discover MP Series
(200 ft). For more information, see the SmartX Living
controllers on the IP network and change each
Space Sensors Specification Sheet.
controller's configuration, including the BACnet and IP
network settings, location, and parent server. To save
Mobile commissioning application engineering time, you can save common device
The eCommission SmartX Controllers mobile settings and then reuse them for controllers of the same
application is designed for local configuration, field model.
deployment, and commissioning of MP Series
controllers. The mobile application reduces the Field deployment and I/O checkout
commissioning time, allows flexibility in project The eCommission SmartX Controllers mobile
execution, and eliminates dependencies on network application does not require an EcoStruxure BMS
infrastructure. server or a network infrastructure to be in place. You
can use the mobile application to load the controller
The mobile application is designed for use with application directly into the local MP Series controller
Android, Apple (iOS), and Microsoft Windows 10 and deploy the controller. The controller application
devices. For more information, see the eCommission can be created offline using Project Configuration Tool
SmartX Controllers Specification Sheet. or WorkStation. You can also perform an I/O checkout
to ensure that the controller's I/O points are configured,
wired, and operating correctly.

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 5

MP-C
SmartX IP Controller

Full EcoStruxure Building Operation software WorkStation supports both online and offline
support engineering of MP Series controllers. You can make the
configuration changes online or use database mode to
The power of the MP Series controller is fully realized make the changes offline. In database mode, the
when it is part of an EcoStruxure BMS, which provides changes are saved to the EcoStruxure Building
the following benefits: Operation database so that you can apply the changes
to the controllers later.
• WorkStation/WebStation interface
• Script and Function Block programming options Project Configuration Tool enables you to perform all
the engineering off site, without the need for physical
• Device discovery hardware, which minimizes the time you need to spend
• Engineering efficiency on site. You can run the EcoStruxure BMS servers
virtually and engineer the MP Series controllers, before
WorkStation/WebStation interface you deploy your server and controller applications to
the servers and controllers on site. For more
WorkStation and WebStation provide a consistent user
information, see the Project Configuration Tool
experience regardless of which EcoStruxure BMS
specification sheet.
server the user is logged on to. The user can log on to
the parent EcoStruxure BMS server to engineer,
In addition, you can use Automated Engineering Tool to
commission, supervise, and monitor the MP Series
facilitate your engineering process when using MP
controller and its I/O as well as its attached SmartX
Series controllers. This tool provides access to a library
Sensors. For more information, see the WorkStation and
of standard controller applications. These standard
WebStation specification sheets.
applications can be quickly configured and customized
using the wizards and mass edit functions provided in
Script and Function Block programming options
the tool and then loaded into your target server. The
Unique to the industry, the MP Series controllers have tool also enables the quick creation of your own
both Script and Function Block programming options. templates based on MP Series controller applications
This flexibility assures that the best programming that you have developed. This facilitates a standard
method can be selected for the application. Existing approach and drives the ability to easily reuse and
programs can easily be reused between the duplicate common controller applications. For more
EcoStruxure BMS server and the controller. information, see the Automated Engineering Tool
specification sheet.
Device discovery
The enhanced Device Discovery in WorkStation
enables you to easily identify MP Series controllers on a
BACnet network and to associate the controllers with
their parent server.

Engineering efficiency
The engineering and maintenance of MP Series
controllers can be done very efficiently using the
EcoStruxure Building Operation reusability features.
With these features, you can create library items
(Custom Types) for a complete controller application
that contains programs and all necessary objects such
as trends, alarms, and schedules. The controller
application in the Custom Types library is reusable
across all controllers of the same model. You can use
the controller application as a base for creating new Library of standard HVAC applications
controllers intended for similar applications. You can
then edit the controller application, and the changes
are automatically replicated to all controllers, while
each controller keeps its local values.

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 6

MP-C
SmartX IP Controller

Part Numbers

Product Part number

MP-C-15A SXWMPC15A10001
MP-C-18A SXWMPC18A10001
MP-C-18B SXWMPC18B10001
MP-C-24A SXWMPC24A10001
MP-C-36A SXWMPC36A10001
MP-C DISPLAY SXWMPCDSP10001
(MP-C override display module)
Spare terminal blocks for all MP-C models SXWMPCCON10001
(4 x 3-pin, 1 x 4-pin, 7 x 6-pin, 2 x 8-pin terminal blocks)
DIN-RAIL-CLIP, DIN-rail end clip SXWDINEND10001
package of 25 pieces
eCommission Bluetooth Adapter SXWBTAECXX10001

Specifications
AC input
Nominal voltage......................................................................................................................................................24 VAC
Operating voltage range........................................................................................................................................+/-20 %
Frequency ............................................................................................................................................................50/60 Hz
Maximum power consumption (MP-C-15A, -18A, -18B) ...........................................................................................22 VA
Maximum power consumption (MP-C-24A) ..............................................................................................................28 VA
Maximum power consumption (MP-C-36A) ..............................................................................................................33 VA
Power input protection................................................................................................MOV suppression and internal fuse
DC input
Nominal voltage.............................................................................................................................................24 to 30 VDC
Operating voltage range ...............................................................................................................................21 to 33 VDC
Maximum power consumption (MP-C-15A, -18A, -18B)............................................................................................ 12 W
Maximum power consumption (MP-C-24A)............................................................................................................... 15 W
Maximum power consumption (MP-C-36A)............................................................................................................... 18 W
Power input protection................................................................................................MOV suppression and internal fuse
Environment
Ambient temperature, operating .................................................................0 to 50 °C (32 to 122 °F) at normal operationa
..........................................................-40 to +60 °C (-40 to +140 °F) for rooftop applications, horizontal installation onlya
a) MP-C Display has an operating temperature range of -30 to +60 °C (-22 to +140 °F).
Ambient temperature, storage ............................................................................................-40 to +70 °C (-40 to +158 °F)
Maximum humidity.....................................................................................................................95 % RH non-condensing

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 7

MP-C
SmartX IP Controller

Material
Plastic flame rating ...............................................................................................................................................UL94-5V
Ingress protection rating ............................................................................................................................................IP 20
Mechanical
Dimensions (MP-C-15A, -18A, -18B)............................................... 153 W x 110 H x 64 D mm (6.0 W x 4.3 H x 2.5 D in.)

Dimensions (MP-C-24A, -36A) .........................................................234 W x 110 H x 64 D mm (9.2 W x 4.3 H x 2.5 D in.)

Weight, MP-C-15A
Including terminal blocks .....................................................................................................................0.358 kg (0.789 lb)
Weight, MP-C-18A
Including terminal blocks .....................................................................................................................0.371 kg (0.818 lb)
Weight, MP-C-18B
Including terminal blocks .....................................................................................................................0.361 kg (0.796 lb)
Weight, MP-C-24A
Including terminal blocks .....................................................................................................................0.495 kg (1.091 lb)
Weight, MP-C-36A
Including terminal blocks .....................................................................................................................0.547 kg (1.206 lb)

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 8

MP-C
SmartX IP Controller

Installation.....................................................................................................DIN rail or other flat surface inside a cabinet

Terminal blocks ................................................................................................................................................Removable
Software compliance
EcoStruxure Building Operation software .............................................................................................version 2.0 or later
Agency compliances
Emission...............................................................RCM; EN 61000-6-3; EN 50491-5-2; FCC Part 15, Sub-part B, Class B
Immunity ...............................................................................................................................EN 61000-6-2; EN 50491-5-3
Safety .........................................................................EN 60730-1; EN 60730-2-11; EN 50491-3; UL 916 C-UL US Listed
Real-time clock
Accuracy, at 25 °C (77 °F) ..............................................................................................................+/-1 minute per month
Backup time, at 25 °C (77 °F) ...................................................................................................................7 days minimum
Communication ports
Ethernet ................................................................................................................................ Dual 10/100BASE-TX (RJ45)
USB .................................................................... USB 2.0, 5 VDC, 2.5 W, 1 device port (mini-B) and 1 host port (type-A)
Sensor Bus ............................................................................................................................24 VDC, 2 W, RS-485 (RJ45)
Sensor Bus protection ...........................................Transient voltage suppressors on communication and power signals
Communications
BACnet..........................................................................................................BACnet/IP, port configurable, default 47808
...................................................................................................BTL B-AAC (BACnet Advanced Application Controller)a
a) See the BTL Product Catalog for up-to-date details on BTL listed firmware revisions on BACnet International's home
page.
CPU
Frequency ........................................................................................................................................................... 500 MHz
Type...........................................................................................................................................ARM Cortex-A7 dual-core
DDR3 SDRAM ........................................................................................................................................................128 MB
NOR flash memory ...................................................................................................................................................32 MB
Memory backup.......................................................................................................................128 kB, FRAM, non-volatile
MP-C Display (Optional)
Removable .....................................................................................................................................................................No
Dimensions ..........................................................................................74 W x 46 H x 24 D mm (2.9 W x 1.8 H x 0.9 D in.)

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 9

MP-C
SmartX IP Controller

Display size .................................................................................................................36 W x 17 H mm (1.4 W x 0.7 H in.)

Display resolution .......................................................................................................................................128 x 64 pixels
Display type......................................................................... FSTN monochrome LCD, white color transflective backlight
Power consumption............................................................................................................. max. 0.15 W (45 mA at 3.3 V)
Ambient temperature, operating .........................................................................................-30 to +60 °C (-22 to +140 °F)
Ambient temperature, storage ............................................................................................-40 to +70 °C (-40 to +158 °F)
Maximum humidity.....................................................................................................................95 % RH non-condensing
Weight ..................................................................................................................................................0.035 kg (0.077 lb)
Compliance with standards ......................................................................................................................EN ISO 16484-2
Universal inputs/outputs, Ub and Uc
Channels, MP-C-15A ............................................................................................................................. 8 Ub, Ub1 to Ub8
Channels, MP-C-18A ......................................................................................................................... 10 Ub, Ub1 to Ub10
Channels, MP-C-18B ......................................................................................................................... 10 Ub, Ub1 to Ub10
Channels, MP-C-24A ......................................................................................................................... 16 Ub, Ub1 to Ub16
................................................................................................................................................................4 Uc, Uc1 to Uc4
Channels, MP-C-36A ......................................................................................................................... 20 Ub, Ub1 to Ub20
................................................................................................................................................................8 Uc, Uc1 to Uc8
Absolute maximum ratings .......................................................................................................................-0.5 to +24 VDC
A/D converter resolution ..........................................................................................................................................16 bits
Universal input/output protection........................................Transient voltage suppressor on each universal input/output
Digital inputs
Range .........................Dry contact switch closure or open collector/open drain, 24 VDC, typical wetting current 2.4 mA
Minimum pulse width ..............................................................................................................................................150 ms
Counter inputs
Range .........................Dry contact switch closure or open collector/open drain, 24 VDC, typical wetting current 2.4 mA
Minimum pulse width ................................................................................................................................................20 ms
Maximum frequency..................................................................................................................................................25 Hz
Supervised inputs
5 V circuit, 1 or 2 resistors
Monitored switch combinations.............................................................Series only, parallel only, and series and parallel
Resistor range ................................................................................................................................................1 to 10 kohm
For a 2-resistor configuration, each resistor must have the same value +/- 5 %
Voltage inputs
Range ..............................................................................................................................................................0 to 10 VDC
Accuracy...............................................................................................................................+/-(7 mV + 0.2 % of reading)
Resolution................................................................................................................................................................1.0 mV
Impedance..........................................................................................................................................................100 kohm
Current inputs
Range ................................................................................................................................................................0 to 20 mA

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 10

MP-C
SmartX IP Controller

Accuracy..........................................................................................................................+/-(0.01 mA + 0.4 % of reading)

Resolution....................................................................................................................................................................1 μA
Impedance .............................................................................................................................................................47 ohm
Resistive inputs
10 ohm to 10 kohm accuracy .......................................................................................................+/-(7 + 4 x 10-3 x R) ohm
R = Resistance in ohm
10 kohm to 60 kohm accuracy .....................................................................................+/-(4 x 10-3 x R + 7 x 10-8 x R2) ohm
R = Resistance in ohm
Temperature inputs (thermistors)
Range................................................................................................................................-50 to +150 °C (-58 to +302 °F)
Supported thermistors
Honeywell .............................................................................................................................................................20 kohm
Type I (Continuum) ...............................................................................................................................................10 kohm
Type II (I/NET) .......................................................................................................................................................10 kohm
Type III (Satchwell) ...............................................................................................................................................10 kohm
Type IV (FD) ......................................................................................................................................................... 10 kohm
Type V (FD w/ 11k shunt) ....................................................................................................................Linearized 10 kohm
Satchwell D?T......................................................................................................................................Linearized 10 kohm
Johnson Controls .................................................................................................................................................2.2 kohm
Xenta....................................................................................................................................................................1.8 kohm
Balco.......................................................................................................................................................................1 kohm
Measurement accuracy
20 kohm...................................................................................................-50 to -30 °C: +/-1.5 °C (-58 to -22 °F: +/-2.7 °F)
...................................................................................................................-30 to 0 °C: +/-0.5 °C (-22 to +32 °F: +/-0.9 °F)
.................................................................................................................. 0 to 100 °C: +/-0.2 °C (32 to 212 °F: +/-0.4 °F)
.............................................................................................................100 to 150 °C: +/-0.5 °C (212 to 302 °F: +/-0.9 °F)
10 kohm, 2.2 kohm, and 1.8 kohm.......................................................-50 to -30 °C: +/-0.75 °C (-58 to -22 °F: +/-1.35 °F)
..........................................................................................................-30 to +100 °C: +/-0.2 °C (-22 to +212 °F: +/-0.4 °F)
.............................................................................................................100 to 150 °C: +/-0.5 °C (212 to 302 °F: +/-0.9 °F)
Linearized 10 kohm .................................................................................-50 to -30 °C: +/-2.0 °C (-58 to -22 °F: +/-3.6 °F)
...............................................................................................................-30 to 0 °C: +/-0.75 °C (-22 to +32 °F: +/-1.35 °F)
.................................................................................................................. 0 to 100 °C: +/-0.2 °C (32 to 212 °F: +/-0.4 °F)
.............................................................................................................100 to 150 °C: +/-0.5 °C (212 to 302 °F: +/-0.9 °F)
1 kohm ..............................................................................................-50 to +150 °C: +/-1.0 °C (-58 to +302° F: +/-1.8 °F)
RTD temperature inputs
Supported RTDs......................................................................................................................................................Pt1000
Pt1000
Sensor range .....................................................................................................................-50 to +150 °C (-58 to +302 °F)

SmartX IP Controller device environment Sensor range Measurement accuracy

0 to 50 °C (32 to 122 °F) -50 to +70 °C (-58 to +158 °F) +/-0.5 °C (+/-0.9 °F)

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 11

MP-C
SmartX IP Controller

Continued

SmartX IP Controller device environment Sensor range Measurement accuracy

0 to 50 °C (32 to 122 °F) 70 to 150 °C (158 to 302 °F) +/-0.7 °C (+/-1.3 °F)
-40 to +60 °C (-40 to +140 °F) -50 to +150 °C (-58 to +302 °F) +/-1.0 °C (+/-1.8 °F)

RTD temperature wiring

Maximum wire resistance.........................................................................................................20 ohm/wire (40 ohm total)
Maximum wire capacitance.......................................................................................................................................60 nF
The wire resistance and capacitance typically corresponds to a 200 m wire.
Voltage outputs
Range ..............................................................................................................................................................0 to 10 VDC
Accuracy..............................................................................................................................................................+/-60 mV
Resolution.................................................................................................................................................................10 mV
Minimum load resistance ........................................................................................................................................5 kohm
Load range.......................................................................................................................................................-1 to +2 mA
Current outputs (Uc only)
Range ................................................................................................................................................................0 to 20 mA
Accuracy ............................................................................................................................................................+/-0.2 mA
Resolution..................................................................................................................................................................21 µA
Load range.....................................................................................................................................................0 to 650 ohm
Relay outputs, DO
Channels, MP-C-15A ........................................................................................................................................................0
Channels, MP-C-18A...................................................................................................................................3, DO5 to DO7
Channels, MP-C-18B ........................................................................................................................................................0
Channels, MP-C-24A.................................................................................................................................. 4, DO1 to DO4
Channels, MP-C-36A.................................................................................................................................. 8, DO1 to DO8
Contact rating......................................................................................................250 VAC/30 VDC, 2 A, Pilot Duty (C300)
Switch type....................................................................................................................................................Form A Relay
....................................................................................................................................................Single Pole Single Throw
....................................................................................................................................................................Normally Open
Isolation contact to system ground.....................................................................................................................3000 VAC
Cycle life (Resistive load) ..............................................................................................................At least 100,000 cycles
Minimum pulse width ..............................................................................................................................................100 ms
High power relay outputs, DO
Channels, MP-C-15A.............................................................................................................................................. 1, DO7
Channels, MP-C-18A.............................................................................................................................................. 1, DO8
Channels, MP-C-18B ........................................................................................................................................................0
Channels, MP-C-24A ........................................................................................................................................................0
Channels, MP-C-36A ........................................................................................................................................................0

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 12

MP-C
SmartX IP Controller

Contact rating....................................................................................................250 VAC/24 VDC, 12 A, Pilot Duty (B300)

Switch type....................................................................................................................................................Form A Relay
....................................................................................................................................................Single Pole Single Throw
....................................................................................................................................................................Normally Open
Isolation contact to system ground.....................................................................................................................5000 VAC
Cycle life (Resistive load) ..............................................................................................................At least 100,000 cycles
Minimum pulse width ..............................................................................................................................................100 ms
Triac outputs, DO
Channels, MP-C-15A.................................................................................................................................. 6, DO1 to DO6
Channels, MP-C-18A.................................................................................................................................. 4, DO1 to DO4
Channels, MP-C-18B.................................................................................................................................. 8, DO1 to DO8
Channels, MP-C-24A ........................................................................................................................................................0
Channels, MP-C-36A ........................................................................................................................................................0
Output rating (for each triac output) ..................................................................................................................Max. 0.5 A
Voltage......................................................................................................................................................24 VAC +/-20 %
Commons ........................................................................................COM1 for DO1 and DO2 (on MP-C-15A, -18A, -18B)
.........................................................................................................COM2 for DO3 and DO4 (on MP-C-15A, -18A, -18B)
..................................................................................................................COM3 for DO5 and DO6 (on MP-C-15A, -18B)
....................................................................................................................COM4 for DO7 and DO8 (on MP-C-18B only)
The common terminals can be connected to 24 VAC or to ground.
Common voltage, high side output.........................................................................................................................24 VAC
Common voltage, low side output .............................................................................................................0 VAC (ground)
Minimum pulse width ..............................................................................................................................................100 ms
Triac output protection...................................................................................MOV and snubber across each triac output
..........................................................................................................................................MOV from triac COM to ground

Terminals • Individual 24 VDC power sources to the field must

be current limited to maximum 4 A for UL
Be sure to follow proper installation wiring diagrams compliant installations, and maximum 6 A in other
and instructions, including these instructions: areas.
• All MP-C models have several RET terminals for • For more information on wiring, see Hardware
connection of I/O returns, so a common Reference Guide.
chassis/signal ground rail is optional and may not
be needed.

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 13

MP-C
SmartX IP Controller

MP-C-15A

MP-C-18A

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 14

MP-C
SmartX IP Controller

MP-C-18B

MP-C-24A

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 15

MP-C
SmartX IP Controller

MP-C-36A

Part Numbers in AMER Region for Network Connectivity Accessories

Product descriptiona Part number (AMER region)

Cat 6 field-term plug, UTP ACTPG6TLU001
Cat 6 pass-through plug, UTP, 100-pack ACTPG6PTU100
Actassi crimping tool ACTTLCPT
Cat 6 cable, UTP, 1000 ft (305 m), CMP, green ACT4P6UCP1ARXGR
Cat 6 patch cord, UTP, 30 ft (9 m), CMP, green ACTPC6UBCP30AGR
Cat 6 patch cord, UTP, 50 ft (15 m), CMP, green ACTPC6UBCP50AGR
Cat 6 patch cord, UTP, 70 ft (21 m), CMP, green ACTPC6UBCP70AGR
Cat 6 patch cord, UTP, 90 ft (27 m), CMP, green ACTPC6UBCP90AGR
Cat 5e pass-through plug, UTP, 100-pack ACTPG5EPTU100
Cat 5e cable, UTP, 1000 ft (305 m), CMP, green ACT4P5EUCP1ARXGR
Cat 5e patch cord, UTP, 30 ft (9 m), CMP, green ACTPC5EUBCP30AGR
Cat 5e patch cord, UTP, 50 ft (15 m), CMP, green ACTPC5EUBCP50AGR
Cat 5e patch cord, UTP, 70 ft (21 m), CMP, green ACTPC5EUBCP70AGR
Cat 5e patch cord, UTP, 90 ft (27 m), CMP, green ACTPC5EUBCP90AGR

a) For more information, see the Product Selection Guide (SmartX IP Controllers - Accessories). Abbreviations: UTP (Unshielded Twisted Pair), CMP (Plenum-rated
cable)

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 16

MP-C
SmartX IP Controller

Part Numbers in EMEA Region for Network Connectivity Accessories

Product descriptiona Part number (EMEA region)

Cat 6 field-term plug, UTP ACTPG6TLU001
Cat 6 pass-through plug, UTP, 100-pack ACTPG6PTU100
Actassi crimping tool ACTTLCPT
Cat 6 cable, UTP, 305 m (1000 ft), Euroclass D, green VDICD116118
Cat 6 patch cord, UTP, 10 m (32 ft), LSZH, green ACTPC6UBLS100GR
Cat 6 patch cord, UTP, 15 m (49 ft), LSZH, green ACTPC6UBLS150GR
Cat 6 patch cord, UTP, 20 m (65 ft), LSZH, green ACTPC6UBLS200GR
Cat 6 patch cord, UTP, 25 m (82 ft), LSZH, green ACTPC6UBLS250GR
Cat 5e pass-through plug, UTP, 100-pack ACTPG5EPTU100
Cat 5e cable, UTP, 1000 ft (305 m), Euroclass D, green VDICD115118
Cat 5e patch cord, UTP, 10 m (32 ft), LSZH, green ACTPC5EUBLS100GR
Cat 5e patch cord, UTP, 15 m (49 ft), LSZH, green ACTPC5EUBLS150GR
Cat 5e patch cord, UTP, 20 m (65 ft), LSZH, green ACTPC5EUBLS200GR
Cat 5e patch cord, UTP, 25 m (82 ft), LSZH, green ACTPC5EUBLS250GR

a) For more information, see the Product Selection Guide (SmartX IP Controllers - Accessories). Abbreviations: UTP (Unshielded Twisted Pair), CMP (Plenum-rated
cable), LSZH (Low Smoke Zero Halogen)

Part Numbers in Pacific Region for Network Connectivity Accessories

Product descriptiona Part number (Pacific region)

Cat 6 field-term plug, UTP ACTPG6TLU001
Cat 6 pass-through plug, UTP, 100-pack ACTPG6PTU100
Actassi crimping tool ACTTLCPT
Cat 6 cable, UTP, 305 m (1000 ft), PVC, green 2D4P6IPV3B-GR
Cat 6 patch lead, UTP, 10 m (32 ft), PVC, green RJ6_100PL-GR
Cat 6 patch lead, UTP, 15 m (49 ft), PVC, green RJ6_150PL-GR
Cat 6 patch lead, UTP, 20 m (65 ft), PVC, green RJ6_200PL-GR
Cat 6 patch lead, UTP, 25 m (82 ft), PVC, green RJ6_250PL-GR
Cat 5e pass-through plug, UTP, 100-pack ACTPG5EPTU100
Cat 5e cable, UTP, 305 m (1000 ft), PVC, green 2D4P5IPV3B-GR
Cat 5e patch lead, UTP, 10 m (32 ft), PVC, green RJ5_100PL-GR
Cat 5e patch lead, UTP, 15 m (49 ft), PVC, green RJ5_150PL-GR
Cat 5e patch lead, UTP, 20 m (65 ft), PVC, green RJ5_200PL-GR
Cat 5e patch lead, UTP, 25 m (82 ft), PVC, green RJ5_250PL-GR

a) For more information, see the Product Selection Guide (SmartX IP Controllers - Accessories). Abbreviations: UTP (Unshielded Twisted Pair), PVC (Polyvinyl
chloride)

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 17

MP-C
SmartX IP Controller

Regulatory Notices
Federal Communications Commission CE - Compliance to European Union (EU)
FCC Rules and Regulations CFR 47, Part 15, Class B 2014/30/EU Electromagnetic Compatibility Directive
This device complies with part 15 of the FCC Rules. Operation is subject to the following two 2014/35/EU Low Voltage Directive
conditions: (1) This device may not cause harmful interference. (2) This device must accept 2011/65/EU Restriction of Hazardous Substances (RoHS) Directive
any interference received, including interference that may cause undesired operation. This equipment complies with the rules, of the Official Journal of the European Union, for
governing the Self Declaration of the CE Marking for the European Union as specified in the
Industry Canada above directive(s) per the provisions of the following standards: EN 60730-1, EN 60730-2-
This Class B digital apparatus complies with Canadian ICES-003. 11, and EN 50491-3 Safety Standards.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Regulatory Compliance Mark (RCM) - Australian Communications and Media WEEE - Directive of the European Union (EU)
Authority (ACMA) This equipment and its packaging carry the waste of electrical and electronic equipment
This equipment complies with the requirements of the relevant ACMA standards made under (WEEE) label, in compliance with European Union (EU) Directive 2012/19/EU, governing the
the Radiocommunications Act 1992 and the Telecommunications Act 1997. These disposal and recycling of electrical and electronic equipment in the European community.
standards are referenced in notices made under section 182 of the Radiocommunications
Act and 407 of the Telecommunications Act.
UL 916 Listed products for the United States and Canada, Open Class Energy
Management Equipment. UL file E80146.

www.schneider-electric.com

03-20035-03-en, September 2018

© 2018 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.