Scribd
Upload
94 views2 pages

MP3 Voice Board: Description

The MP3 Voice board is a voice unit that outputs MP3 files for elevator messaging. It has 8 floor inputs, 2 direction inputs, 5 general message inputs, and 1 trigger input. All inputs are wired to a common 24VDC supply. The board can be programmed via USB to play messages for each input and configure settings like input type and background music.

Uploaded by

Reza Kühn
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
94 views2 pages

MP3 Voice Board: Description

The MP3 Voice board is a voice unit that outputs MP3 files for elevator messaging. It has 8 floor inputs, 2 direction inputs, 5 general message inputs, and 1 trigger input. All inputs are wired to a common 24VDC supply. The board can be programmed via USB to play messages for each input and configure settings like input type and background music.

Uploaded by

Reza Kühn
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Factory 11, 30 Perry Street

Matraville NSW Australia 2036


Ph. 61 2 9316 6909
Fax: 61 2 9316 6797
Email [email protected]

Ref: MP3 Voice V4-TechnicalArticle-Rev5.doc

MP3 Voice Board

Description: The MP3 Voice board is


a voice unit that outputs MP3 files on
command from specified 24Vdc inputs.

When used in an elevator it uses floor


inputs and a trigger to voice floor
messages. On receipt of direction inputs it
voices the direction of travel. The unit also
has 5 inputs which can be used for general
messages.

Features:
• 8 inputs for floor messages which can be direct inputs or configured in grey code or binary.
• 1 trigger input for initiating floor messages.
• 2 direction inputs for direction messages.
• 5 additional inputs for other messages which can also be direct inputs or configured in grey code or binary.
• Inputs may be positive or negative switched.
• Mono speaker output.
• USB port for high speed programming of board.
• Programming software available.

Wiring:
• Supply is wired to 0V +24 terminals. This is a 24Vdc supply.
Note: If a switch mode power supply is used it is recommended that the supply wires be looped through
a ferrite core
• All inputs use the “C” common terminal as their reference.
• If “C” is 0V then the inputs shall be 24V. (See diagram on next page)
• If “C” is 24V then the inputs shall be 0V
• Inputs:
• TRIG – On rising edge of this input turning on, the floor messages shall be sounded as per their
respective input.
• 1…8 – Floor Inputs 1-8 shall be sounded on receipt of the rising edge of the TRIG input. The floor inputs
may be configured as direct, binary or grey code. If Binary or grey code is used the inputs shall be
thought of as…. 1 = 1, 2 = 2, 3 = 4, 4 = 8, 5 = 16, 6 = 32, 7 =64 and 8 = 128.
• UP, DN – Direction of travel messages.
• 9…13 – General message inputs sounded once only when the inputs turning on.
• Speaker – “SPEAKER” terminal. Wire SPEAKER to these terminals.

Factory 11, 30 Perry Street, Matraville NSW Australia


Ph. (02) 9316 6909 - Fax (02) 9316 6797 – Email [email protected] A.C.N. 081 814 717
 Page 2 December 23, 2009

Settings:

• ISP Mode link: Not used.

• USB Mode link: Installed for programming unit. Ensure no inputs are turned on while in this mode.

• FORMAT Mode link: If installed with USB Mode link installed, on power up for 5 seconds, the memory shall be
re-formatted.
(FORMAT Led will turn on then off to indicate a successful formatting)

• BGMUSIC link: Installed to play background music. The music will stop after 30s since the last trigger.

• SP1 – SP3 links: Not used

Led Indicators:

• Red Led (Run): Indicates that the microprocessor is running

• Yellow Led (Format): Indicates the formatting process is occurring.

The diagram below is an example of positive switching inputs. +24VDC inputs, 0VDC common.

NOTE:
Floor Inputs 1-8 sound on input AND trigger
input turning on.
Message Inputs 9-13 sound once only on
24V input turning on.
Remove BG music link to turn off background music.
VOLUME: Volume control.
0V

C +24 0v ECD
MP3 VOICE V4.0 13. Spare.
13 BOARD 12. Please stand clear of the closing doors.
12
11 11. Lift overload.
24V inputs 10 FORMAT 10. Fire service recall. Lift ret. to main floor.
9 9. Lift out of service.
0V common 8
USB

7 ISP
6 BGMUSIC
4P 5
SP 1
3P 4
3 SP 2
2P
2 SP 3
1P 1
DUP UP SPEAKER
DDN DN USB
TRIG VOLUME
LR

C N/C

Factory 11, 30 Perry Street, Matraville NSW Australia


Ph. (02) 9316 6909 - Fax (02) 9316 6797 – Email [email protected] A.C.N. 081 814 717

You might also like