FB3000 Mixed IO Product Data Sheet

D301863X012 July 2019

12-channel Mixed I/O Module and Personality

Module
The FB3000 12-channel Mixed I/O module provides the
FB3000 with the ability to monitor and control various
analog field signals, digital field signals, and high-speed
pulse inputs. Providing multiple I/O options on a single
module reduces configuration time and maintenance costs.
The Mixed I/O module provides a total of eight individually
field-configurable inputs (AI/DI/PI), two analog outputs
(AO), and two digital outputs (DO).

The Personality Module (3MSG12) provides both built-in

surge protection and a wiring connection for the Mixed I/O
module.

Inputs
You can configure each of the eight input channels as an
analog input (AI), discrete input (DI), or pulse input (PI).
Surge suppression and signal conditioning is provided for
each channel. The module provides internally sourced DI
operation for dry contacts with DI filtering of 30 ms pulled
internally to 24 Vdc when the field input is open. DI filtering
is 30 ms. The input signal can be configured via software to
either a pull-up to 24 Vdc or pull-down to ground. You can
configure the AI channels for 4 to 20 mA or 1 to 5 Vdc
externally sourced, single-ended operation. The module
channels each AI signal through signal conditioning circuitry
that provides a 2 Hz low pass filter for noise rejection.

Discrete Outputs
DO circuits consist of a solid-state relay and software
selectable internal LSS and surge suppression.

Analog Outputs
Two externally powered (11 to 30 Vdc) AOs are standard on
the Mixed I/O module.
Mixed I/O Module
Local Terminations
The Personality module enables you to connect field or Module Status LED
panel wiring to the Mixed I/O module through a 20-point
Communication Status LED
terminal block assembly that also provides surge
suppression up to 2kV. Terminations are pluggable and Termination Board Status LED
accept a maximum wire size of 16 AWG (American Wire
Gauge). See the following table for the wiring guide.

Remote Automation Solutions

FB3000 Mixed I/O July 2019

FB3000 12-channel Mixed I/O Module

Field Wiring Terminals on Personality Module (3MSG12)

Block Definition

01 Analog/Digital/Pulse Input 01

02 Analog/Digital/Pulse Input 02

03 Analog/Digital/Pulse Input 03

04 Analog/Digital/Pulse Input 04

05 Ground

06 Analog/Digital/Pulse Input 05

07 Analog/Digital/Pulse Input 06
08 Analog/Digital/Pulse Input 07

09 Analog/Digital/Pulse Input 08

10 Ground

11 Analog Output 01

12 Ground

13 Analog Output 02

14 Ground

15 Digital Output (High) 1

16 Digital Output (Low) 1

17 Digital Output (High) 2

18 Digital Output (Low) 2

19 24V Loop (Positive)

20 24V Loop Ground

Inputs
Analog Inputs Quantity Up to 8 channels
Type Single-ended, externally sourced, software-
configurable as 1 to 5 Vdc or 4 to 20 mA
Resolution 16-bit
Impedance 1 to 5 Vdc Inputs 1 MΩ
4 to 20 mA Inputs 250Ω
Reference Accuracy (after ±0.1% of span
calibration) at 25°C (77°F)
Accuracy Over Operating ±0.15% of span
Temperature Range
[—40 to 75°C (—40 to 158°F)]
Input Filter 1KHz 3dB point of input signal

2 www.Emerson.com/RemoteAutomation
July 2019 FB3000 Mixed IO

Conversion Time 1ms per channel

Surge Suppression 30 Vdc transorb between signal and ground
Meets C37.90-1978 and IEC 801-5 specifications
Digital Inputs Quantity Up to 8 individually configurable DI channels
Type Internally sourced, non-interrupting dry contact
Input Voltage Internally sourced, non-interrupting dry contact
Input Current Selectable 66 μA or 2 mA
On-state Voltage < 1.0 Vdc
On-state Current > 2.0 Vdc
Surge Suppression 31 Vdc transorb between signal and isolated
ground
Input Filtering 30 ms time constant (contact bounce)
Pulse Inputs Quantity Up to 8 individually configurable PI channels
Type Internally sourced, non-interrupting dry contact.
Supports input rates ranging from 0.0 Hz up to
10.5 KHz with choice of 3 software-programmable
filters (30 μs, 1 ms, or 30 ms)
Input Voltage Internally sourced, non-interrupting dry contact
Input Current Selectable 66 μA or 2 mA
On-state Voltage < 1.0 Vdc
On-state Current > 2.0 Vdc
Surge Suppression 31 Vdc transorb between signal and isolated
ground
Input Filtering Software selectable: 30 μs, 1 ms, or 30 ms time
constant (contact bounce)

Outputs
Analog Output (optional) Quantity Two channels
Type Single-ended, software-configurable as 1 to 5 Vdc
or 4 to 20 mA
Resolution 16-bit
Maximum Overload Voltage ±24 Vdc continuous
Impedance 1 MΩ typical (without scaling resistor)
Over Range 0.8 to 5.2 Vdc or 3.2 to 20.8 mA
Accuracy Over Operating Current Output: ±0.3% of span
Temperature Range
[—40 to 75°C (—40 to 158°F)] Voltage Output: 0.3% + (0.057 x load in mA)% of
span
▪ Current Mode Compliance 40 Ω (minimum)
900 Ω (maximum)
Maximum Load Current 5 mA (voltage mode)
Isolation 500 Vdc channel to bus

www.Emerson.com/RemoteAutomation 3
FB3000 Mixed I/O July 2019

Surge Suppression 31 Vdc transorb (meets IEEE 472-1978)

Digital Output Quantity Two channels, individually configurable as
separate from DIs
Type Open drain, externally powered
Maximum Load Current 50 mA (internal Low Side Switch or LSS), 500mA
(external LSS) @ 31 Vdc
Surge Suppression 31 Vdc transorb between signal and ground

Loop Supply
Loop Power Supply Output Voltage Maximum Load 200mA @ 24 Vdc ± 5%

Power
Consumption Analog Input (per channel) 0.066 W average at 1 second poll
Analog Output (per channel) 0.495 W average at 1 second poll
Discreet Input (per channel) 0.015 W (1Hz)
Discrete Output (per channel) 0.350 W (1Hz toggle)
External Loop Power @ 24 Vdc 4.78 W (@ 200mA)

Physical
I/O Dimensions 139.9 mm W x 109.5 mm H x 22.4 mm D (5.506 in
W x 4.312 in H x .88 in D)
Weight 0.18 Kg (0.4 lbs)
LEDs 15 status indicators: Status, Communication, and Termination indicators (1 through 3);
AI/DI/PI (4 through 11); AO (12 and 13); and DO (14 and 15)
Personality Module Dimensions 112.7 mm W x 98.4 mm H x 19.8 mm D
(4.438 In W x 3.875 in H x 0.781 in D)
Surge suppression 20-point terminal block assemblies up to 2kV
Wiring Up to size 16 AWG at the pluggable terminal
blocks
Environment
Same as the FB3000 in which it is installed.

Approvals
Same as the FB3000 in which it is installed.

4 www.Emerson.com/RemoteAutomation
July 2019 FB3000 Mixed IO

For customer service and technical support,

visit www.Emerson.com/SupportNet.
Global Headquarters,
North America, and Latin America:
Emerson Automation Solutions
Remote Automation Solutions
6005 Rogerdale Road
Houston, TX 77072 U.S.A.
T +1 281 879 2699 | F +1 281 988 4445
www.Emerson.com/RemoteAutomation
Europe:
Emerson Automation Solutions
Remote Automation Solutions
Unit 1, Waterfront Business Park
Dudley Road, Brierley Hill
Dudley DY5 1LX UK
T +44 1384 487200 | F +44 1384 487258
Middle East/Africa:
Emerson Automation Solutions
Remote Automation Solutions
Emerson FZE
P.O. Box 17033 © 2019 Remote Automation Solutions, a business unit of Emerson Automation Solutions. All
Jebel Ali Free Zone – South 2 rights reserved.
Dubai U.A.E.
T +971 4 8118100 | F +971 4 8865465 This publication is for informational purposes only. While every effort has been made to ensure
accuracy, this publication shall not be read to include any warranty or guarantee, express or
Asia-Pacific: implied, including as regards the products or services described or their use or applicability.
Emerson Automation Solutions Remote Automation Solutions (RAS) reserves the right to modify or improve the designs or
Remote Automation Solutions specifications of its products at any time without notice. All sales are governed by RAS terms
1 Pandan Crescent and conditions which are available upon request. RAS accepts no responsibility for proper
Singapore 128461 selection, use or maintenance of any product, which remains solely with the purchaser and/or
T +65 6777 8211| F +65 6777 0947 end-user.

Remote Automation Solutions