12/26/2019 ShareTechnote

LTE Quick Reference Go Back To Index Home : www.sharetechnote.com

CCE Index Calculation

CCE Index is the CCE number at which the control channel data (PDCCH) is allocated. Normally this index changes
for each subframe, meaning that even the same PDCCH data (e.g, a PDCCH for the same UE) allocated in each
subframe changes subframe by subframe. (If you are not familiar with what is CCE, refer to Resource Element
Management section first.)

One of the most common situations where you have to care about this CCE index is when you change the system BW.
Changing the system bandwidth in higher layer (L3) is very simple. You only have to change one IE in MIB, but if you
are a protocol stack developer or test case developer who take care of all stack from L1 through L3, you have to
calculate CCE index for each subframe and those index gets different for each bandwidth. But calculating CCE is not a
simple procedure. Just outline of the calculation is as follows. Just try to have an idea on which parameters you need
and how they are related to calculate CCE.

CCE Index Calculation Procedure

PDCCH Decoding/Blind Decoding on UE side
Live Examples
Why so complex ?

CCE Index Calculation Procedure

Followings are the brief summary of the procedures of calculating the CCE Index. (I would recommend you to refer to
Ref [2] for further details and different way of explanation)

Step 1 : Figure out all the REs within the Control region (the first 1 or 2 or 3 OFDM symbols) that can be reserved for
PDCCH allocation. (Note : item (iii), (iv) are only in the first OFDM symbol. Item (ii) is located in multiple OFDM
symbols, but within the control region it is also located only in the first OFDM symbol. Refer to Downlink Frame
Structure page for the details of each channel allocation in RB map)

RE's for PDCCH = Total Available RE's within control symbols -------(i)
- Number of RE's used for reference signals -------(ii)
- Number of RE's used in PHICH -------------------(iii)
- Number of RE's used in PCFICH ------------------(iv)

Step 2 : Figure out total number CCE's available for PDCCH.

total number CCE's available for PDCCH = (The Result of Step 1)/36, since 1 CCE = 36 REs

Step 3 : Number each of the CCEs from the result of Step 2. (Number starts from 0).

Step 4 : eNB decide CCE index according to following formula (Note : Depending on Aggregation Level(L), you will
get the different number of consecutive CCEs for allocating one PDCCH. For example, if L is 1, 'i' can be only '0'. So
you have only one CCE for the PDCCH. If L = 4, you will have for CCE index by plugging 0,1,2,3 into the variable 'i'.
Then you will have four consecutive CCE index. It means one PDCCH will be spread over the four consecutive CCEs).

https://www.sharetechnote.com/html/Handbook_LTE_CCE_Index.html 1/5
12/26/2019 ShareTechnote

Following is an Example of CCE index calculation. First try calculating the values on your own according to the
descriptions above (Step 4) and compare your result with my result (Excel Spreadsheet is also linked here). The cell
in green is the parts that should be derived/calculated from other cells. (Note : In this example, I assumed the case
where 100 CCEs are available. But in reality, there is no such a case where you can have 100 CCE. To have 100
CCEs, you need 3600 RE (=36 RE/CCE * 100 CCE). In case of 20 Mhz Bandwidth, CFI = 3. You have 3600 RE in
Control Region, but you have remove those REs for Reference Signal, PCFICH and PHICH. So the available REs for
CCE become less than 100 CCE. Refer to Ref [1] for the details of calculating the available CCEs)

L (Aggregation Level) 1
C_RNTI(n_RNTI) 100
i (0~[Aggregation Level-1]) 0
m' (0 ~ [Number of PDCCH Candidate-1]) 1
A 39827
D 65537

k (subframe) Y(k-1) Y(k) N_CCE CCE Index

0 100 50480 100 81
1 50480 53948 100 49
2 53948 21988 100 89
3 21988 10682 100 83
4 10682 31347 100 48
5 31347 42656 100 57
6 42656 10398 100 99
7 10398 58380 100 81
8 58380 44111 100 12
9 44111 23975 100 76
(Click here to get excel spreadsheet)

For further details of the procedure, refer to TS 36.213 - 9.1.1 PDCCH Assignment Procedure.

Too complicated ? If you are not the person who has to implement this algorithm in your chipset, just try to
understand the basic idea explained below.

https://www.sharetechnote.com/html/Handbook_LTE_CCE_Index.html 2/5
12/26/2019 ShareTechnote
PDCCH Decoding/Blind Decoding on UE side

UE has 'ALMOST' no information for decoding PDCCH. So UE has to try 'ALL' the possible tries to decode PDCCH. This
is called 'Blind Decoding'.

For example, let's look into all the possible combinations to try for Common Search Space and assume the total
space is 16 CCEs. Following is factors and number of combinations.

i) All the possible blocks assuming Aggregation Level 4 = 16 (CCE) / 4 (Aggregation Level) = 4 blocks
ii) All the possible blocks assuming Aggregation Level 2 = 16 (CCE) / 8 (Aggregation Level) = 2 blocks
iii) All the possible DCI formats supported for common space = assuming 2 (out of 0,1A,3,3A,1C based on TM)
----------------------------------------------------------------------------------------------
Total number of decoding tries = ( i + ii) x iii = (4 + 2) x 2 = 12

After all of these blind trials, UE checks CRC with all the possible RNTIs it can be applicable.

Live Example of CCE Allocation

Following is a example of CCE index calculation (CCE Allocation for PDCCH) in real communication between UE and
eNB simulator from Amarisoft OTS. (This is the example with the case of BandWidth = 5Mhz, CFI = 3, C_RNTI =
0x61)

Following is the CCE index from the log shown above and presented in a tabular form. See if you can find a kind of
pattern.

SFN Subframe AggregationLevel Total CCE CCE Index DCI Format

615 0 4 20 12 1A
615 1 4 20 8 1A
615 2 4 20 4 1A
615 3 4 20 4 1A
615 4 4 20 0 1A
615 5 4 20 8 1A
615 6 4 20 0 1A
615 7 4 20 8 0
615 7 4 20 12 1A

https://www.sharetechnote.com/html/Handbook_LTE_CCE_Index.html 3/5
12/26/2019 ShareTechnote
615 8 4 20 16 1A
615 9 4 20 16 1A
616 0 4 20 12 1A
616 1 4 20 8 1A
616 2 4 20 4 1A
616 3 4 20 4 1A
616 4 4 20 0 1A
616 5 4 20 8 0
616 5 4 20 12 1A
616 6 4 20 0 0
616 6 4 20 4 1A
616 7 4 20 8 1A
616 8 4 20 16 1A
616 9 4 20 16 1A

Following is another presentation of CCE index allocation in tabular form. You will see 4 consecutive CCE allocation for
each PDCCH. This is because AggregationLevel in this example is 4. The CCE Index calculated at each subframe
indicates the first CCE number of the four consecutive CCEs.

Sub CCE
SFN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
frame Index
615 0 12
615 1 8
615 2 4
615 3 4
615 4 0
615 5 8
615 6 0
615 7 8
615 7 12
615 8 16
615 9 16
616 0 12
616 1 8
616 2 4
616 3 4
616 4 0
616 5 8
616 5 12
616 6 0
616 6 4
616 7 8
616 8 16
616 9 16

Why so complex ?

When I first try to understand and configure CCE index at early phase of verification, the first question poping up in
my mind was "Why is it designed in such a complicated manner to determine the CCE Index (Location of PDCCH
allocation) ?".

Of course (and unfortunately) 3GPP specification never tell you "Why ?", it says only "What". I think you can get this
"Why" part from various TDocs related to this issue. Following is from "2.1 Requirements of R1-072470" and blue
part is my comments.

•Possibility for interference randomization between cells. A certain control channel should not persistently collide with
one and the same control channel in a neighboring cell. --> This is why we assign different CCE Index for every
subframe.

•Possibility for interference coordination. By using different parts of the frequency spectrum in different cells for
control signaling it should be possible to avoid/reduce inter-cell interference for the control channels.

https://www.sharetechnote.com/html/Handbook_LTE_CCE_Index.html 4/5
12/26/2019 ShareTechnote
•As seen from the UE, the CCE-to-RE mapping structure should be invariant to whether interference coordination is
used or not. After the cell-search procedure, the UE does not know whether a cell is applying interference
coordination or not but still needs to read system information from the “dynamic BCCH”. If the “dynamic BCCH” is
mapped to the DL-SCH (or transmitted in a similar way as the DL-SCH), it must be possible to read the DL-SCH and
associated control signaling without knowledge about any inter-cell coordination.

•Control signaling should utilize the full system bandwidth to exploit any frequency diversity (already agreed in
RAN1). --> This is why the total number of RBs for the full system bandwidth is used as a parameters in the CCE
index determination algorithm.

•Two symbols from the same CCE should be mapped to two in frequency neighboring REs in order to support SFBC as
the diversity scheme (already agreed inRAN1).

Reference :

[1] PDCCH Dimensioning (LTE University)

[2] All about PDCCH and CCE allocation (Tayal's way to learn LTE)

https://www.sharetechnote.com/html/Handbook_LTE_CCE_Index.html 5/5