Table C066-21/E

Pressure relief valves type AGAM

two stage, subplate mounting - ISO 6264 size 10, 20 and 32

AGAM are two stage pressure relief valves

with balanced poppet, designed to operate in
oil hydraulic systems.
In standard versions the piloting pressure of
the poppet 햲 of the main stage 햳 is regula-
ted by means of a grub screw protected by
cap 햴 in the cover 햵.
Optional versions with setting adjustment by
handwheel 햶 instead of the grub screw are
available on request.
Clockwise rotation increases the pressure.
AGAM can be equipped with a pilot solenoid
valve 햷 for venting or for different pressure
setting type:
• DHI for AC and DC supply, with CURUS cer-
tified solenoids
• DHE for AC and DC supply, high perfor-
mances with CURUS certified solenoids
Mounting surface: ISO 6264 size 10, 20 and 32
Max flow: 200, 400 and 600 l/min
Max pressure up to 350 bar
AGAM-10/11...-E AGAM-20/..../V

1 MODEL CODE

AGAM - 20 / 20 / 210 / 100/100 / V - I X 24DC ** / *

Seals material,
AGAM = pressure relief see section 4:
valve subplate - = NBR
mounting PE = FKM
BT = HNBR
Size:
10 20 32
Series number

Setting pressure and venting option: Voltage code, see section 8 (1):
- =one setting pressure without option
10=one setting pressure with venting,
with de-energized solenoid X = without connector (1):
11=one setting pressure with venting, See section 7 for available connectors, to be
with energized solenoid ordered separately
20=two setting pressure with venting,
-00 = solenoid valve without coils (for -I)
with de-energized solenoid
-00-AC = AC solenoid valve without coils (for -E)
21=two setting pressure with venting,
-00-DC = DC solenoid valve without coils (for -E)
with energized solenoid
22=two setting pressure without venting
32=three setting pressure without venting
Pilot valve (1):
I = DHI for AC and DC supply,
Setting: see section 3 for available setting (1)
with CURUS certified solenoids
E = DHE for AC and DC supply, high performances
with CURUS certified solenoids

Pressure range of second/third setting (1):

50 = 4÷50 bar 100 = 6÷100 bar Options, see section 5
210 = 7÷210 bar 350 = 8÷350 bar E V WP Y

For PED version see technical table CY066

(1) Only for AGAM with solenoid valve for venting and/or for the selection of the setting pressure

C066
 2 HYDRAULIC SYMBOLS

AGAM AGAM-**/10 AGAM-**/11 AGAM-**/22

AGAM-**/20 AGAM-**/21 AGAM-**/32

3 HYDRAULIC CHARACTERISTICS

Valve model AGAM-10 AGAM-20 AGAM-32

Setting [bar] 50; 100; 210; 350

Pressure range [bar] 4÷50; 6÷100; 7÷210; 8÷350

ports P, X = 350
Max pressure [bar] Ports T, Y = 210 (without pilot solenoid valve)
For version with pilot solenoid valve, see technical tables E010 and E015
Max flow [l/min] 200 400 600

4 MAIN CHARACTERISTICS, SEALS AND FLUIDS - for other fluids not included in below table, consult our technical office

Assembly position Any position

Subplate surface finishing Roughness index Ra 0,4 - flatness ratio 0,01/100 (ISO 1101)
CE to Low Voltage Directive 2014/35/EU
Compliance RoHS Directive 2011/65/EU as last update by 2015/65/EU
REACH Regulation (EC) n°1907/2006
Standard execution = -30°C ÷ +70°C
Ambient temperature /PE option = -20°C ÷ +70°C
/BT option = -40°C ÷ +70°C
NBR seals (standard) = -20°C ÷ +80°C, with HFC hydraulic fluids = -20°C ÷ +50°C
Seals, recommended fluid temperature FKM seals (/PE option) = -20°C ÷ +80°C
HNBR seals (/BT option) = -40°C ÷ +60°C, with HFC hydraulic fluids = -40°C ÷ +50°C
Recommended viscosity 15÷100 mm2/s - max allowed range 2,8 ÷ 500 mm2/s

Max fluid contamination level ISO4406 class 20/18/15 NAS1638 class 9, see also filter section at www.atos.com or KTF catalog
Hydraulic fluid Suitable seals type Classification Ref. Standard

Mineral oils NBR, FKM, HNBR HL, HLP, HLPD, HVLP, HVLPD DIN 51524

Flame resistant without water FKM HFDU, HFDR

ISO 12922
Flame resistant with water NBR, HNBR HFC

4.1 Coils characteristics (for AGAM with pilot solenoid valve)

Insulation class DHI pilot H (180°C) Due to the occuring surface temperatures of the
solenoid coils, the European standards EN ISO 13732-1
DHE pilot H (180°C) for DC coils F (155°C) for AC coils and EN ISO 4413 must be taken into account

Protection degree to DIN EN 60529 IP 65 (with connectors 666, 667, 669 or E-SD correctly assembled)
Relative duty factor 100%
Supply voltage and frequency See electric feature 7
Supply voltage tolerance ± 10%
Certification CURUS North American standard

5 OPTIONS
/E = external pilot
/V = regulating handwheel instead of grub screw protected by cap (for handwheel features, see table K150)
/WP = prolunged manual override protected by rubber cap (only for AGAM with pilot solenoid valve)
/Y = external drain (only for AGAM with pilot solenoid valve)
 6 ELECTRIC CONNECTORS ACCORDING TO DIN 43650 FOR AGAM WITH SOLENOID VALVE
The connectors must be ordered separately

Code of connector Function

666 Connector IP-65, suitable for direct connection to electric supply source
667 As 666 connector IP-65 but with built-in signal led, suitable for direct connection to electric supply source
For other available connectors, see tab. E010 and K500

7 ELECTRIC FEATURES FOR AGAM WITH SOLENOID VALVE

Power
Solenoid External supply Colour of
Voltage Type of consumption Code of spare coil Code of spare coil
valve nominal voltage coil label
code connector (3) DHI DHE
type ± 10% (1) DHI
DHI DHE

12 DC 12 DC COU-12DC green COE-12DC

666
24 DC 24 DC COU-24DC red COE-24DC
DC or 33 W 30 W
110 DC 110 DC COU-110DC black COE-110DC
667
220 DC 220 DC COU-220DC black COE-220DC
DHI
DHE 110/50 AC (2) 110/50/60 AC 60 VA 58 VA COI-110/50/60AC yellow COE-110/50/60AC
115/60 AC 115/60 AC (5) 666 - 80 VA - - COE-115/60AC
AC 120/60 AC 120/60 AC (6) or 60 VA - COI-120/60AC white -
230/50 AC (2) 230/50/60 AC 667 60 VA 58 VA COI-230/50/60AC light blue COE-230/50/60AC
230/60 AC 230/60 AC 60 VA 80 VA COI-230/60AC silver COE-230/60AC

(1) For other supply voltages available on request see technical tables E010, E015. (4) When AC solenoid is energized, the inrush
(2) Coil can be supplied also with 60 Hz of voltage frequency: in this case the performances are current is approx 3 times the holding current.
reduced by 10 ÷ 15% and the power consumption is 55 VA (DHI) and 58 VA (5) Only for DHE
(3) Average values based on tests performed at nominal hydraulic condition and (6) Only for DHI
ambient/coil temperature of 20°C.

8 REGULATED PRESSURE VERSUS FLOW DIAGRAMS based on mineral oil ISO VG 46 at 50°C

AGAM-10 AGAM-20 AGAM-32

Regulated pressure at port P [bar]

Regulated pressure at port P [bar]

Regulated pressure at port P [bar]

Flow rate [l/min] Flow rate [l/min] Flow rate [l/min]

9 PERMISSIBLE RANGE (shared area) based on mineral oil ISO VG 46 at 50°C

AGAM-10 AGAM-20 AGAM-32

Min. regulated pressure [bar]

Min. regulated pressure [bar]

Min. regulated pressure [bar]

Flow rate [l/min] Flow rate [l/min] Flow rate [l/min]

C066
10 MINIMUM PRESSURE VERSUS FLOW DIAGRAMS based on mineral oil ISO VG 46 at 50°C

Min. regulated pressure [bar] AGAM-10 AGAM-20 AGAM-32

Min. regulated pressure [bar]

Min. regulated pressure [bar]

Flow rate [l/min] Flow rate [l/min] Flow rate [l/min]

11 DIMENSIONS [mm]

AGAM-10
ISO 6264: 2007
69
Mounting surface: 6264-06-09-1-97
Fastening bolts:
= 4 socket head screws
103

54
M12x35 class 12.9

27
X= G1/4
=
15

Tightening torque = 125 Nm

3

22 Seals: 2 OR 123; 1 OR 109/70

51.5 ø13 view from X Ports P, T: Ø = 14,5 mm
47.5
27 105.5 3.5 ø6 ø21.5
Ports X: Ø = 3,2 mm
54
136 = =
80 Mass: 3,6 Kg
109

109

109
79

Y= G1/4 Y= G1/4 Y=G1/4 Y=G1/4

X= G1/4 X= G1/4 X=G1/4 X=G1/4

81 55 81 103 81 98.5 81 103

AGAM-10/10/**-IX AGAM-10/20/**-IX AGAM-10/22/**-IX AGAM-10/32/**-IX

AGAM-10/11/**-IX AGAM-10/21/**-IX
Mass: 5,1 Kg Mass: 6,2 Kg Mass: 5,9 Kg Mass: 6,3 Kg
112
112

112
82

Y= G1/4 Y= G1/4 Y=G1/4 Y= G1/4

X= G1/4 X= G1/4 X=G1/4 X= G1/4

96.5 55 96.5 118.5 96.5 98.5 96.5 118.5

AGAM-10/10/**-EX AGAM-10/20/**-EX AGAM-10/22/**-EX AGAM-10/32/**-EX

AGAM-10/11/**-EX AGAM-10/21/**-EX
Mass: 5,1 Kg Mass: 6,2 Kg Mass: 5,9 Kg Mass: 6,3 Kg

Overall dimensions refer to valves with connectors type 666

 AGAM-20

116
75
X= G1/4

25
4
69 ø6 ø17
12.5 123.5 2 ø25
138 = =
102.5 Mass: 4,8Kg
X

86.2
ISO 6264: 2007
Mounting surface: 6264-08-11-1-97
=

Fastening bolts:
4 socket head screws M16x50 class 12.9
70

Tightening torque = 300 Nm

35
=

Seals: 2 OR 4112; 1 OR 109/70

Ports P, T: Ø = 24 mm
11.1 23.8
Ports X: Ø = 3,2 mm
34.9
view from X
57.2
79.4
90.5

109
109
109
79

Y= G1/4 Y=G1/4 Y=G1/4 Y=G1/4

X= G1/4 X=G1/4 X=G1/4 X=G1/4

84 52 84 100 84 95.5 84 100

AGAM-20/10/**-IX AGAM-20/20/**-IX AGAM-20/22/**-IX AGAM-20/32/**-IX

AGAM-20/11/**-IX AGAM-20/21/**-IX
Mass: 6,3 Kg Mass: 7,4Kg Mass: 7,1 Kg Mass: 7,5 Kg
112
112

112
82

Y=G1/4 Y=G1/4 Y=G1/4 Y=G1/4

X=G1/4 X=G1/4 X=G1/4 X=G1/4

99.5 56.5 99.5 116 99.5 95.5 99.5 95.5

AGAM-20/10/**-EX AGAM-20/20/**-EX AGAM-20/22/**-EX AGAM-20/32/**-EX

AGAM-20/11/**-EX AGAM-20/21/**-EX
Mass: 6,3 Kg Mass: 7,4 Kg Mass: 7,1 Kg Mass: 7,5 Kg

Overall dimensions refer to valves with connectors type 666

C066
 AGAM-32
109.9 ISO 6264: 2007
Mounting surface: 6264-10-17-1-97
(with M20 fixing holes instead

=
of standard M18)

116

82.6
Fastening bolts:

75
X= G1/4

41.3
4 socket head screws

=
22
4
M20x60 class 12.9
92.5 ø6 ø24.5 Tightening torque = 600 Nm
2 157 3 ø31 12.7 31.8 Seals: 2 OR 4131; 1 OR 109/70
= = 44.5 Ports P, T: Ø = 28,5 mm
121.5
Ports X: Ø = 3,2 mm
X 76.2

Mass: 6,2 Kg 88.9 view from X

109

109

109
79

Y=G1/4 Y=G1/4 Y=G1/4 Y=G1/4

X=G1/4 X=G1/4 X=G1/4 X=G1/4

84 52 84 100 84 95.5 84 100

96 96 96 96

AGAM-32/10/**-IX AGAM-32/20/**-IX AGAM-32/22/**-IX AGAM-32/32/**-IX

AGAM-32/11/**-IX AGAM-32/21/**-IX
Mass: 7,7 Kg Mass: 8,8 Kg Mass: 8,5 Kg Mass: 8,9 Kg
112

112
112
82

Y=G1/4 Y=G1/4 Y=G1/4 Y=G1/4

X=G1/4 X=G1/4 X=G1/4 X=G1/4

99.5 69 99.5 115.5 99.5 95.5 99.5 115.5

AGAM-32/10/**-EX AGAM-32/20/**-EX AGAM-32/22/**-EX AGAM-32/32/**-EX

AGAM-32/11/**-EX AGAM-32/21/**-EX
Mass: 7,7 Kg Mass: 8,8 Kg Mass: 8,5 Kg Mass: 8,9 Kg

Overall dimensions refer to valves with connectors type 666

12 MOUNTING SUBPLATES

Ports Ø Counterbore
Valve Subplate model [mm] Mass
Port location [Kg]
P T X P T X
AGAM-10 BA-306 G 1/2" G 3/4" G 1/4" 30 36,5 21,5 1,5
BA-406 G 3/4" G 3/4" G 1/4" 36,5 36,5 21,5 3,5
AGAM-20 Ports P, T, X underneath;
BA-506 G 1" G 1" G 1/4" 46 46 21,5 3,5
AGAM-32 BA-706 G 1 1/2" G 1 1/2" G 1/4" 63,5 63,5 21,5 6

The subplates are supplied with fastening bolts. For further details see table K280

11/19