VIII.
Troubleshooting
Control Module – Using # 264946 Front Cover to Replace
Broken # 266746, # 263832 or # 264461 Control Module Buttons
# 266746, # 263832 or # 264461 control modules are often replaced when buttons
break, not for electronic failures. Replacing the # 264946 front cover when buttons
break instead of replacing the entire control module will save customers time and
money.
NOTE: # 264946 front
cover fits on all three 266746,
modules -- # 266746, # 263832 or
263832 & # 264461. 264461
CAUTION: Some pc board 264946
components are sensitive to
static electricity and can be
damaged when touched.
Personnel handling pc boards
should be grounded.
Broken control module
Top of front cover “buttons” occur when tabs
on front cover break. Use
Top tab
plastic front cover when
replacing “broken buttons”.
CAUTION: Insert display module board carefully to prevent
breaking spring locking tabs on front cover. When installing
Bottom of front cover display module, carefully slide top of board into top of front
cover, making sure board is fully seated into tabs. Then,
Note cracks in plastic locking tabs. carefully rotate bottom of board into position so spring locking
tabs spring back and lock without cracking or breaking. DO
NOT FORCE bottom or top of display board into position.
INSTALLATION: To install a front cover, insert the HINT: Use # 264946 front cover
hinge tabs into the control module housing -- do NOT instead of replacing an older #
force the cover into the housing. To insert the hinge 263832 module with a # 266746
tabs, rotate the front cover (with the tabs contacting the module since modules cost more &
housing hinge) until the cover hinge tabs slide easily into have longer lead times than covers.
the hinge. When the hinge is in place, close the front Many # 263832 modules have been
cover until all three tabs lock the cover in place. replaced merely for broken buttons.
NOTE: To determine which control module you have, check the model #’s on the following list:
266746 -- SHU 5302/5304/5305/5306/5312/5314/5315/5316/6802/6805/6806 UC 11 - UC/12, SHU 5307/5317 UC/12 and SHI
6802/6805/6806 UC/11 - UC/12.
263832 -- SHU 5302/5304/5305/5306/5312/5314/5315/5316/6802/6805/6806 UC 06 and SHI 6802/6805/6806 UC/06.
264461 -- SHU 4302/4306/4312/4316 UC 06 - UC/11 - UC/12 and SHI 4302/4306 UC/06 - UC/11 - UC/12.
84
VIII. Troubleshooting
Control Module – Using # 481055 Control Modules in Older SHU
99 and SHV 43/48 Dishwashers (1)
Control module # 265401 used on older SHV 43/48 and SHU 990x/991x
UC/06, UC/07 & UC/11 models has been replaced by control module #
481055 used on all newer SHU 99 & SHV 43/48 UC/12 models. Since
module # 481055 has slightly different wash cycles and an end of cycle
tone compared to the # 265401 module, the pushbutton pad for the
dishwasher must also be changed so the wash cycles will be shown
correctly. Please follow these instructions to order the correct
pushbutton pad and to turn off the end of cycle tone for older models.
NOTE: When replacing pushbutton pads for older SHV 43/48 & SHU
990x/991x models when the # 265401 control module won’t be replaced
(I.e. the # 265401 control is functional and is still being used), use the
following button pads:
# 170424 4-button pad for SHV 43 & SHU 990x/991x models (instead of
# 182605)
# 170423 5-button pad for SHV 48 models (instead of # 182600)
NOTE: When replacing control module # 481055 for newer SHV 43/48 &
SHU 991x/992x models, button pads don’t need to be replaced. If the
button pads are worn, order # 4-button pad # 182605 (for SHV 43 & SHU
991x models) or 5-button pad # 182600 (for SHV 48 & SHU 992x models).
NOTE: When replacing control module # 265401 for older SHV 43/48 &
SHU 990x/991x models, use module # 481055 along with 4-button pad #
182605 (for SHV 43 & SHU 990x/991x models) or 5-button pad # 182600
(for SHV 48 models).
85
VIII. Troubleshooting
Control Module – Using # 481055 Control Modules in Older SHU
99 and SHV 43/48 Dishwashers (2)
5-button pushbutton pad # 182600 used on SHV 48
UC/06, UC/07, UC/11 & UC/12 and SHU 992x UC/12
4-button pushbutton pad # 182605 used on SHV 43,
SHU 991x UC/06, UC/11 & UC/12 and SHU 990x UC/06
New pushbutton pads:
INSTRUCTIONS FOR TURNING OFF END OF CYCLE TONE:
Open door, push and hold Delicate/Econo button, then turn
dishwasher on while holding Delicate/Econo button.
Release Delicate/Econo button. If module beeps, then end of
cycle tone is on. Press Delicate/Econo button to disable tone.
If module doesn’t beep after button is pressed, then tone is
disabled.
Turn off dishwasher to save selection.
86
VIII. Troubleshooting
Control Module – Using # 481055 Control Modules in Older SHU
99 and SHV 43/48 Dishwashers (3)
Comparison of old and new pushbutton pads:
SHV 4303 UC/06 & UC/11 models program buttons & indicator lights:
| | | | |
Clean Power Scrub Regular Rinse
Scrub Wash Wash & Hold
Plus
old
SHV 4303 UC/12 models program buttons & indicator lights:
| | | | |
Clean Power Regular Delicate Rinse
Scrub Wash /Econo & Hold
Plus
new
SHV 4803 UC/06 & UC/07 models program buttons & indicator lights:
| | | | | | |
Clean Refill Top Power Scrub Regular Rinse
Rinse Rack Scrub Wash Wash & Hold
Agent Only Plus
old
SHV 4803 UC/12 models program buttons & indicator lights:
| | | | | | |
Clean Refill Top Power Regular Delicate Rinse
Rinse Rack Scrub Wash /Econo & Hold
Agent Only Plus
new
87
