Scribd
Upload
136 views

IS 800:2007 & Steel Table May Be Permitted: I. Answer All Questions. Each Question Carries ONE Mark. (10X1 10M)

This document contains a midterm exam for a Design of Steel Structures course. The exam contains 10 short answer questions worth 1 mark each, covering topics like tension member design, slenderness ratios, types of structural sections. It also contains 2 long answer questions worth 10 marks each, requiring students to calculate the design tensile strength of a bolted connection, and the block shear strength of a tension member. The questions are mapped to specific course outcomes to assess student performance at different cognitive levels.

Uploaded by

Shaik Munna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
136 views

IS 800:2007 & Steel Table May Be Permitted: I. Answer All Questions. Each Question Carries ONE Mark. (10X1 10M)

This document contains a midterm exam for a Design of Steel Structures course. The exam contains 10 short answer questions worth 1 mark each, covering topics like tension member design, slenderness ratios, types of structural sections. It also contains 2 long answer questions worth 10 marks each, requiring students to calculate the design tensile strength of a bolted connection, and the block shear strength of a tension member. The questions are mapped to specific course outcomes to assess student performance at different cognitive levels.

Uploaded by

Shaik Munna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Roll No

VFSTR - VADLAMUDI
Year Semester Branch Section
Staff Name: Dr.Parthiban P IV I CIVIL 01
Faculty Branch: Civil SUBJECT: DESIGN OF STEEL STRUCTURES (16CE401) MID – II
Course Name: B. Tech Date: 06.11.2020 Time: 10:00 – 11:00 AM
IS 800:2007 & Steel Table may be permitted
I. Answer all questions. Each question carries ONE mark. [10X1=10M]
1. What is Tdn?
2. What is Lug Angle?
3. What is Block Shear?
4. To prevent failure of the tension member by net section rupture_______
a) T<An.Fu b) T>An.Fu c) T<An.Fy d) T>An.Fy
5. The maximum slenderness ratio for tension members (other than pretensioned members)
is
a) 350 b) 180 c) 300 d) 400
6. Cables may be used effectively for which of the following structures?
a) Suspended roof b) bridge c) chimney d) all the above
7. For a single unequal angle tie member, the leg preferred for making connection is the
(a) Shorter Leg (b) Longer Leg
(c) any of the two (d) Longer if bolted and shorter if welded
8. The thickness of gusset plate should not be less than
a) Suspended roof b) bridge c) chimney d) all the above
9. Which of the following section will be preferred for a column section?
a) ISLB b) ISMB c) ISWB d) ISHB
10. Which of the following section is not a compression member?
a) strut b) tie c) boom d) rafter

II. Answer any ONE question. Each question carries TEN marks. [10X1=10M]

11. Determine the design tensile strength of the plate 120 mm x 8 mm connected to a 12
mm thick gusset plate with bolt holes as shown in Fig. below. The yield strength and
ultimate strength of the steel used are 250 MPa and 400 MPa. The Diameter of the bolts
used is 16 mm.
12. Determine the block shear strength of the tension member as shown in Fig. below. Use
the steel of Grade Fe 410

Questions CO Correlation Table:

Question Related CO Number


Marks allotted (Question Numbers)
Numbers (Level of correction)
1 to 10 CO2 (1)-1, 2, 3, 5, 8 Remembering: 3 M (1,2,3,5,8)
CO2 (2)-4, 6, 7. Understanding: 13M (4,6,7,9,10)
CO3 (2) - 9, 10. Application:--- 20 M (11,12)
11to 12 Analyzing: ---
CO2 (2) - 11
Evaluating: ---
CO2 (2)- 12
Creating: ---

You might also like