Expansion loop calculation

Index

1 Expansion loop (CS) Routine for the expansion loop calculation for a C

2 Deduction Deduction of the expansion loop equation

3 Table A-1. Allowable stress for the material as functiuon of

4 Lambda. Coefficient of linear expansion of some of the mo

5 Elasticity module Elasticity modules of materials at different tempe

6 Spiraxsarco. Spiraxsarco Chart for expansion loops sizing

7 Vitaulic. Victaulic equation for expansion loops sizing

8 Properties Phisical properties of some materials

9 U.S. Army Corps U.S. Army Corps of Engineers

References
 Rev. cjc. 01.08.2018

xpansion loop calculation for a CS pipe

expansion loop equation

for the material as functiuon of temperature

ear expansion of some of the most common materials.

s of materials at different temperatures

art for expansion loops sizing

n for expansion loops sizing

es of some materials

of Engineers

www.piping-tools.net
Expansion_loop.xlsm
cjcruz[at]piping-tools.net
Expansion loop for a steel pipe
Steel pipe expansion loop with nominal diameter "dn" shedule "SCH" and length "Linst"
The given length "Linst" refers to an installation at a temperature "tinst".
The pipe will expand with respect to its length "Linst", due to the temperature rise Dt = tmax - tinst
The maximum temperature could be reached due to the ambient temperature and solar radiation,
or due to fluid flowing through it.
Similarly, the pipe could shrink due to low ambient temperatures and radiation to the sky.

Data
Material:
dn = API 5L - Gr. B
10 in Elasticity module
SCH = 40 Elasticity module of selected material
Linst = 100 m at operation temperature (Annex B)
tinst = 10 ºC Material type, to obtain "E"
toperation = 174.2 °C
E= 1.93E+11 Pa
Allowable stress Temperature differential
Allowable stress of selected material Auxiliary data Dt = toperation - tinst
at operation temperature Pipe dimensions (Note 1) toperation = 174.2
sallow = 137.9 MPa dn = 10 in tinst = 10
Linear expansion coefficient SCH = 40 - Dt = 164.2
Expansion coefficient of selected di = Pipe_Imp_CS_Dint_dn_sch
material at operation temp. (Annex C) di = #VALUE! mm
Mat. type de = Pipe_Imp_CS_Dext_dn

l= 25Cr-20Ni m/(m*K)
1.61E-05 de = #VALUE! mm

Annexes A, B y C

Annex A
Interpolation for permissible material stress (Table A-1, Sheet 3)

t= 174.2 °C (For t < 38 °C, the table uses 38 °C)

Row = 9 (Cell associated with selected material from table A-1)

Col_A = 5 tA = 148.9 °C sA = 137.9 MPa

Col_B = 6 tB = 204.4 °C sB = 137.9 MPa

S= sB + (sA - sB) * (tb - t)/(tb - ta)

S= 137.9 MPa 1

Annex B
Interpolation for the modulus of elasticity of the material type (Table B, Sheet 5)
For t < -200 °C, one uses data for t = -200 °C
t= 174.2 °C Information available, for most types of materials, tmax = 649 ° C.
Row = 1 (Cell associated with selected material from table B)
 Col_A = 7 tA = 149.0 °C EA = 2.0E+11 MPa
Col_B = 8 tB = 204.0 °C EB = 1.9E+11 MPa

E= EB + (EA - EB) * (tb - t)/(tb - ta)

E= 1.9E+11 MPa 1

Annex C
Interpolation for the coefficient of thermal expansion of the material (Table C, Sheet 4)

t= 38 °C (For t < 38 °C, the table uses 38 °C)

Row = 5 (Cell associated with selected material from table C)

Col_A = 43 tA = 33.9 °C lA = 1.6E-05 m/(m*K)

Col_B = 44 tB = 47.8 °C lB = 1.6E-05 m/(m*K)

l= sB + (sA - sB) * (tb - t)/(tb - ta)

l= 1.61E-05 m/(m*K) 1

Do not delete these lines

Carbon steel pipes

Carbon steel pipes

dn Sch
in -
1/2 5
1 10
1 20
2 30
2 40
3 60
4 80
5 100
6 120
8 140
10 160
12 STD
14 XS
16 XXS
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
 Rev. cjc. 01.08.2018
Note 1. The pipe dimensions are automatic
Heigth "H" for carbon steel materials ccording ANSI B
For other materials, the interior and exterio
3  E  d  f tot dimensions must be entered manually into
H  0 . 378 
 adm

ture differential Pipe expansion DL Carbon steel expansion loop

toperation - tinst The expansion loop will absorb this Heigth "H" of expansion loop
ºC length H = 0.378*( (3 * E * de * DL) / (sallow) )^0.5

ºC DL = l * Linst * Dt E= 1.93E+11 Pa
K l= 1.61E-05 m/(m*K) de = #VALUE! m
Linst = 100 m DL = 0.264 m
Dt = 164.2 K sallow = 1.379E+08 Pa
DL = 0.26 m H= #VALUE! m
DL = 264.19 mm W= #VALUE! m

Expansion loop dimensions ratio

H/w= 2 P
C D
It is assumed that the point A coresponds f C
to the fxed end of a cantilever beam AC.

At the point C of this beam a deflection f = DL/2

H Lira
is produced, due to force P. This force P is
caused by the temperature change acting on x
the pipe. a
A B
m
The beam AB deforms due to the application y
of the moment P*H at his end A.
As a result of the application of this moment
a rotation a occurs at end of the beam.
pipe dimensions are automatically calculated only
teel materials ccording ANSI B36.10M.
aterials, the interior and exterior diameter
must be entered manually into the corresponding cells

www.piping-tools.net

Expansion_loop.xlsm
Expansion joint calculation considering the arms bending and the rotation of the elbows

The calculation of the heigth "H" of the arms is done considering the requirement of a maximum allowable bending stres

Expansion joint

L
The temperature rise produces an extension of the pipe length.
Dilation of the pipe produces a deflection "DL / 2"
in the point "C" of the left arm "AC". The same occurs in the
arm BD.

The expansion joint shall absorb the total dilation DL

without surpassing the given maximum material stress.

Each half of the expansion joint shall permit a displacement

f = DL / 2. This shift f will be produced by the contribution of:
1) Flexion of arm AC, denoted as f1
b) Displacement of point C due to the rotation of the elbow in A, denoted as f2

A deflection "f2", due to rotation of the Differential equation for the b

Analysis for a half of the expansion loop elbow of the expansion joint in point "A" (Figure 2)
is added to arrow "f1" due to bending
of arm.
f = f 1 + f2 d2y
Cantilever beam with concentrated load The total deflection is EI   M
with dx 2

P M  PH
H D
P C
f C
A
d2y
C EI   PH
f1 dx 2
Integrating
Figure 1 H Lira
Deflextion. Ref. 7. Figure 13
Cantilever beam, concentrated load x d  dy 
at free end a
 EI  dx  dx   dx   P  H  dx
A B
 d  dy 
a
 EI  dx  dx   dx   P  H  dx
A B

(1) y dy
EI   PH xc
Figurew2
PH 3 dx
f1  The beam AB deforms due to the
Force "P"  E  I with the deflextion
3 associated moments applied at both ends dy P  H  x  c

(2)
dx EI

3  E  I  f1
P
H3

The slope is Eq. (4a) Thus, From equation (1), the deflex
point C due to the flexión of a
is

 Helbow B (in x = w)
dy atPthe
Slope The tangentPof Hthe2 angle due to the
   x  w / 2 tan   of
rotation  the elbow is
dx EI 4E  I P  L3
and the
f1 deflextion of point C
3  of
the rotation E the
I elbow in A
dy PH
   w  w / 2 thus f2
dx xw EI tan( ) 
H The totalPdelextion in C is
H3
dy
Defining PH
aratio  wto
Higth / 2Width f2 
4 E  I
dxH/w
xw
= EI 2 f2 P  H 2
w= H/2  (4b)
H 4E  I f  f1  f 2
PH3 P  L3 P  L3
f  
f2  3 E  I 4  E  I
dy PH H /4 4 E  I P  L3 4 P  L3 3
 f    
dx xw EI 3 E  I 4 4  E  I 3
4  P  L3 3  P  L3
f  
dy PH2 12  E  I 12  E  I
 f 
7  P  L3
dx x w 4E  I 12  E  I

Maximum stress in beam AC Reaplacing f1 For the complete expansion j

(From the moment being applied
to beam AB) (1)
 (5)
4
f1   f f tot  2  f
with c = d/2 7
M max 3 E 4 d
 max   max   f
(6)
H 72
2 f tot
I /c 6 E  d
H 2
from (3) One obtains 6 E  f d
d  max   7   max
 max  Mmax  (3) 7 H2
(2) 2
and replacing P from I

3  E  f tot  d
M  PH
2
6 E  f d H
H 2 (7)
7   max
7   max
3  E  I  f1
P
H3 6 E  f d 1 3  E  f tot
H for
Valid  one half expansion joint H 
into 7   max 7  max
d
 max  P  H 
I 2
3  E  I  f1 d
 max  H 
H3 I 2
3  E  f1 d
 max  
H2 2
 Rev. cjc. 01.08.2018
1 of 4

um allowable bending stress "s allow"

f f

C D

A B

2 of 4
ferential equation for the beam AB For x = w/2 (midelpoint)
dy/dx = 0

Microsoft Editor de
2
thus ecuaciones 3.0
d y
EI   M
dx 2
(3) c   Pin H(4) w / 2
Replacing

M  PH
dy
EI   PH  x  PH w/2
d2y dx
I  PH (4a)
dx 2 EI 
dy
 P  H   x  w / 2
dx

d  dy 
EI     dx   P  H  dx
dx  dx 
 d  dy 
EI     dx   P  H  dx
dx  dx 
(4)
dy
EI   PH xc
dx

dy P  H  x  c

dx EI

3 of 4
om equation (1), the deflextion of Relations f/f1 y f/f2
int C due to the flexión of arm AC

(1) 7  P  L3
f  Microsoft Equation
12  E  I 3.0
d the PL 3
f1 deflextion of point C due to 4  P  L3
e rotation of
3 E the
I elbow in A es f1 
12  E  I
(4b) 3  P  L3
f2 
12  E  I
e totalPdelextion
H3 in C is
f2  4  P  L3
4 E  I f1 12  E  I 4
 
f 7PL 3
7
 f1  f 2 12  E  I
P  L3 P  L3
4
  f1   f
3 E  I 4  E  I 7
P  L3 4 P  L3 3 3  P  L3
    f 2 12  E  I 3
3 E  I 4 4  E  I 3  
4  P  L3 3  P  L3 (4c) f 7PL 3
7
 
12  E  I 12  E  I 12  E  I
7  P  L3 3
 f2   f
12  E  I 7

4 of 4
r the complete expansion joint

3  E  f tot  d
H  0.378 
 max
 This is the length3H Eof the
f tot expansion
d
H  0.378 
f tot  2  f f 
f tot  max
joint that, for the given conditions,
2 will have as a result the maximum
permissible "smax".
f tot
6 E  d See Sheet Victaulic. Victaulic
H 2 indicates the same equation, with
7   max the difference that the factor 0.378
is rounded to 0.4 (Sheet 7). Microsoft Editor de
ecuaciones 3.0

3  E  f tot  d
H
7   max

1 3  E  f tot  d E  f tot  d
H  H  0.655 
7  max  max
Microsoft Equation
3.0
 9 Allowable stress as function of temperature [MPa]
API 5L - Gr. B TEMPERATURE °C
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Spec & Grade Materia 38 93 149 204 260 316 343 371 399 427 454 482 510 538 566 593 621 649
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 A 53(Type F) Gr.A 1 110.3 110.3 110.3 110.3 "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A"
2 A 53 - Gr. A 2 110.3 110.3 110.3 110.3 110.3 102.0 100.0 99.3 73.8 64.1 54.5 44.8 31.0 17.2 11.0 6.9 "NA" "NA"
3 A 53 - Gr. B 3 137.9 137.9 137.9 137.9 130.3 119.3 117.2 113.8 89.6 74.5 60.0 44.8 31.0 17.2 "NA" "NA" "NA" "NA"
4 A 106 - Gr. A 4 110.3 110.3 110.3 110.3 110.3 102.0 100.0 99.3 73.8 64.1 54.5 44.8 31.0 17.2 11.0 6.9 "NA" "NA"
5 A106 - Gr. B 5 137.9 137.9 137.9 137.9 130.3 119.3 117.2 113.8 89.6 74.5 60.0 44.8 31.0 17.2 "NA" "NA" "NA" "NA"
6 A106 - Gr. C 6 160.6 160.6 160.6 157.9 148.9 135.8 133.8 132.4 102.0 82.7 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
7 API 5L - Gr. A 7 110.3 110.3 110.3 110.3 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
8 API 5L - Gr. A25 8 103.4 103.4 100.0 95.1 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
9 API 5L - Gr. B 9 137.9 137.9 137.9 137.9 130.3 119.3 117.2 113.8 89.6 74.5 60.0 44.8 31.0 17.2 11.0 6.9 "NA" "NA"
10 API 5L - Gr. X42 10 137.9 137.9 137.9 137.9 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
11 API 5L - Gr. X46 11 144.8 144.8 144.8 144.8 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
12 API 5L - Gr. X52 12 151.7 151.7 151.7 151.7 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
13 API 5L - Gr. X56 13 163.4 163.4 163.4 163.4 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
14 API 5L - Gr. X60 14 172.4 172.4 172.4 172.4 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
15 API 5L - Gr. X65 15 177.2 177.2 177.2 177.2 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
16 API 5L - Gr. X70 16 188.2 188.2 188.2 188.2 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
17 API 5L - Gr. X80 17 206.8 206.8 206.8 206.8 "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA" "NA"
18 A312 - Gr. TP 304 18 137.9 137.9 137.9 128.9 120.7 113.1 111.7 110.3 107.6 104.8 102.7 100.7 99.3 95.1 84.1 66.9 53.1 41.4
19 A312 - Gr. TP 304L 19 115.1 115.1 115.1 108.9 102.0 96.5 94.5 93.1 91.7 89.6 88.3 82.0 68.3 53.8 43.4 35.2 27.6 22.1
20 A312 - Gr. TP 304H 20 137.9 137.9 137.9 128.9 120.7 113.1 111.7 110.3 107.6 104.8 102.7 100.7 99.3 95.1 84.1 66.9 53.1 41.4
21 A312 - Gr. TP 309 21 137.9 137.9 137.9 137.9 137.9 132.4 129.6 126.2 124.1 120.7 100.7 95.8 86.2 72.4 58.6 44.8 34.5 26.2
22 A312 - Gr. TP 310 22 137.9 137.9 137.9 137.9 137.9 132.4 129.6 126.2 124.1 120.7 100.7 95.8 86.2 75.8 49.0 34.5 24.8 17.2
23 A312 - Gr. TP 316 23 137.9 137.9 137.9 133.1 123.4 117.2 115.1 112.4 111.0 109.6 108.2 106.9 106.2 105.5 100.0 85.5 67.6 51.0
24 A312 - Gr. TP 316L 24 115.1 115.1 115.1 106.9 99.3 93.1 91.0 88.9 86.9 85.5 83.4 81.4 79.3 77.2 74.5 70.3 60.7 44.1
25 A312 - Gr. TP 316H 25 137.9 137.9 137.9 133.1 123.4 117.2 115.1 112.4 111.0 109.6 108.2 106.9 106.2 105.5 100.0 85.5 67.6 51.0
26 A312 - Gr. TP 317 26 137.9 137.9 137.9 133.1 123.4 117.2 115.1 112.4 111.0 109.6 108.2 106.9 106.2 105.5 100.0 85.5 67.6 51.0
27 A312 - Gr. TP 317L 27 137.9 137.9 137.9 130.3 122.0 115.8 114.5 111.7 108.9 106.9 104.8 "N/A" "N/A" "N/A" "N/A" "N/A" "N/A" "N/A"
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

t= 593 621.0
S= 66.9 53.1
 Table A-1. Basic alowable stresses in tension for metals (Page 157 - 161) de ASME B31.3-2002

ASME B31.3-2002 Table A-1. Basic alowable stresses in tension for metals (Page 157 - 161)

Allowable stress as function of temperature [MPa]

TEMPERATURE °C
Spec Grade 38 93 149 204 260 316 343 371 399 427 454 482 510 538 566 593 621 649
1 A 53 Gr. A 110.3 110.3 110.3 110.3
2 A 53 A 110.3 110.3 110.3 110.3 110.3 102.0 100.0 99.3 73.8 64.1 54.5 44.8 31.0 17.2 11.0 6.9
3 A 53 B 137.9 137.9 137.9 137.9 130.3 119.3 117.2 113.8 89.6 74.5 60.0 44.8 31.0 17.2
4 A 106 A 110.3 110.3 110.3 110.3 110.3 102.0 100.0 99.3 73.8 64.1 54.5 44.8 31.0 17.2 11.0 6.9
5 A106 B 137.9 137.9 137.9 137.9 130.3 119.3 117.2 113.8 89.6 74.5 60.0 44.8 31.0 17.2
6 A106 C 160.6 160.6 160.6 157.9 148.9 135.8 133.8 132.4 102.0 82.7
7 API 5L A 110.3 110.3 110.3 110.3
8 API 5L A25 103.4 103.4 100.0 95.1
9 API 5L B 137.9 137.9 137.9 137.9 130.3 119.3 117.2 113.8 89.6 74.5 60.0 44.8 31.0 17.2 11.0 6.9
10 API 5L X42 137.9 137.9 137.9 137.9
11 API 5L X46 144.8 144.8 144.8 144.8
12 API 5L X52 151.7 151.7 151.7 151.7
13 API 5L X56 163.4 163.4 163.4 163.4
14 API 5L X60 172.4 1482.4 172.4 172.4
15 API 5L X65 177.2 177.2 177.2 177.2
16 API 5L X70 188.2 188.2 188.2 188.2
17 API 5L X80 206.8 206.8 206.8 206.8
18 A312 TP 304 137.9 137.9 137.9 128.9 120.7 113.1 111.7 110.3 107.6 104.8 102.7 100.7 99.3 95.1 84.1 66.9 53.1 41.4
19 A312 TP 304L 115.1 115.1 115.1 108.9 102.0 96.5 94.5 93.1 91.7 89.6 88.3 82.0 68.3 53.8 43.4 35.2 27.6 22.1
20 A312 TP 304H 137.9 137.9 137.9 128.9 120.7 113.1 111.7 110.3 107.6 104.8 102.7 100.7 99.3 95.1 84.1 66.9 53.1 41.4
21 A312 TP 309 137.9 137.9 137.9 137.9 137.9 132.4 129.6 126.2 124.1 120.7 100.7 95.8 86.2 72.4 58.6 44.8 34.5 26.2
22 A312 TP 310 137.9 137.9 137.9 137.9 137.9 132.4 129.6 126.2 124.1 120.7 100.7 95.8 86.2 75.8 49.0 34.5 24.8 17.2
23 A312 TP 316 137.9 137.9 137.9 133.1 123.4 117.2 115.1 112.4 111.0 109.6 108.2 106.9 106.2 105.5 100.0 85.5 67.6 51.0
24 A312 TP 316L 115.1 115.1 115.1 106.9 99.3 93.1 91.0 88.9 86.9 85.5 83.4 81.4 79.3 77.2 74.5 70.3 60.7 44.1
25 A312 TP 316H 137.9 137.9 137.9 133.1 123.4 117.2 115.1 112.4 111.0 109.6 108.2 106.9 106.2 105.5 100.0 85.5 67.6 51.0
26 A312 TP 317 137.9 137.9 137.9 133.1 123.4 117.2 115.1 112.4 111.0 109.6 108.2 106.9 106.2 105.5 100.0 85.5 67.6 51.0
27 A312 TP 317L 137.9 137.9 137.9 130.3 122.0 115.8 114.5 111.7 108.9 106.9 104.8
 ASME B31.3-2006 Table A-1. Basic alowable stresses in tension for metals (Page 15Carbon steel pipes and tubes. Pag. 140- 144

Allowable stress as function of temperature [ksi]

1 ksi = 6.8948 MpaTEMPERATURE °C
38 93 149 204 260 316 343 371 399 427 454 482 510 538 566 593 621
Temperature °F
Material Spec Grade 100 200 300 400 500 600 650 700 750 800 850 900 950 1000 1050 1100 1150
Type F A 53Gr. A, Type F 16 16 16 16
A 53 A 16 16 16 16 16 14.8 14.5 14.4 10.7 9.3 7.9 6.5 4.5 2.5 1.6 1
A 53 B 20 20 20 20 18.9 17.3 17 16.5 13 10.8 8.7 6.5 4.5 2.5 1.6 1
A 106 A 16 16 16 16 16 14.8 14.5 14.4 10.7 9.3 7.9 6.5 4.5 2.5 1.6 1
A106 B 20 20 20 20 18.9 17.3 17 16.5 13 10.8 8.7 6.5 4.5 2.5 1.6 1
A106 C 23.3 23.3 23.3 22.9 21.6 19.7 19.4 19.2 14.8 12
API 5L A 16 16 16 16 16 14.8 14.5 14.4 10.7 9.3 7.9 6.5 4.5 2.5 1.6 1
Butt weld API 5L A25 15 15 14.5 13.8
API 5L B 20 20 20 20 18.9 17.3 17 16.5 13 10.8 8.7 6.5 4.5 2.5 1.6 1
API 5L X42 20 20 20 20
API 5L X46 21 21 21 21
API 5L X52 22 22 22 22
API 5L X56 23.7 23.7 23.7 23.7
API 5L X60 25 215 25 25
API 5L X65 25.7 25.7 25.7 25.7
API 5L X70 27.3 27.3 27.3 27.3
API 5L X80 30 30 30 30
1 A312 TP 304 20 20 20 18.7 17.5 16.4 16.2 16 15.6 15.2 14.9 14.6 14.4 13.8 12.2 9.7 7.7
2 A312 TP 304L 16.7 16.7 16.7 15.8 14.8 14 13.7 13.5 13.3 13 12.8 11.9 9.9 7.8 6.3 5.1 4
3 A312 TP 304H 20 20 20 18.7 17.5 16.4 16.2 16 15.6 15.2 14.9 14.6 14.4 13.8 12.2 9.7 7.7
4 A312 TP 309 20 20 20 20 20 19.2 18.8 18.3 18 17.5 14.6 13.9 12.5 10.5 8.5 6.5 5
5 A312 TP 310 20 20 20 20 20 19.2 18.8 18.3 18 17.5 14.6 13.9 12.5 11 7.1 5 3.6
6 A312 TP 316 20 20 20 19.3 17.9 17 16.7 16.3 16.1 15.9 15.7 15.5 15.4 15.3 14.5 12.4 9.8
7 A312 TP 316L 16.7 16.7 16.7 15.5 14.4 13.5 13.2 12.9 12.6 12.4 12.1 11.8 11.5 11.2 10.8 10.2 8.8
8 A312 TP 316H 20 20 20 19.3 17.9 17 16.7 16.3 16.1 15.9 15.7 15.5 15.4 15.3 14.5 12.4 9.8
9 A312 TP 317 20 20 20 19.3 17.9 17 16.7 16.3 16.1 15.9 15.7 15.5 15.4 15.3 14.5 12.4 9.8
10 A312 TP 317L 20 20 20 18.9 17.7 16.8 16.6 16.2 15.8 15.5 15.2
 ASME B31.3-2002
Table A-1. Basic alowable stresses in tension for metals (Page 157 - 161)

38

to
Material Spec Grade 100
A 285 Gr. A 134 … 15
A 285 Gr. A 672 A45 15

Butt weld API 5L A25 15

smls API 5L A25 15

Type F A 53 Gr. A 16

A 53 A 16
A 106 A 16
A 135 A 16
A 369 FPA 16
API 5L A 16

A 285 Gr. A 134 16.7

A 285 Gr. A 672 A 50 16.7
285 Gr. B A 134 18.3

A 516 Gr. A 671 CC60 20

A 515 Gr. A 671 C860 20
A 515 Gr. A 672 B60 20
A 516 Gr. A 672 C60 20

A 53 B 20
A106 B 20
A 333 6 20
A 334 6 20
A 369 FPB 20
A 381 Y35 20
API 5L B 20
 100
API 5L X42 20
API 5L X46 21
API 5L X52 22
API 5L X56 23.7

100
A 516 Gr. A 671 CC65 21.7
A 515 Gr. A 671 C865 21.7
A 515 Gr. A 672 B65 21.7
A 516 Gr. A 672 C65 21.7

100
A 516 GR A 671 CC70 23.1
A 515 GR A 671 CB70 23.1
A 515 GR A 672 B70 23.1
A 516 GR A 672 C70 23.1

A106 C 23.3
API 5L X60 25
API 5L X65 25.7
API 5L X70 27.3
API 5L X80 30
 Table C
ASME B31.3

5
25Cr-20Ni 2 3 4
Material -536 -522 -508
1 2 3 4
1 Carbon Steel Carbon-Moly- Low-Chrome Through 3Cr-Mo) 1 - - -
2 5Cr-MoThrough9Cr-Mo 2 - - -
3 AusteniticStainlessSteels18Cr-8Ni 3 - - -
4 12Cr,17Cr,27Cr 4 - - -
5 25Cr-20Ni 5 - - -
6 UNSN04400Monel67Ni-30Cu 6
7 3.5Ni 7
8 CopperandCopperAlloys 8 1.1E-05 1.2E-05 1.2E-05
9 Aluminum 9 - - -
10 GrayCastIron 10 - - -
11 Bronze 11 - - -
12 Brass 12 - - -
13 70Cu-30Ni 13 - - -
14 UNSN08XXXSeriesNi-Fe-Cr 14 - - -
15 UNSN06XXXSeriesNi-Cr-Fe 15 - - -
16 DuctileIron 16 - - -

VLOOKUP(D62;$'4. Lambda'.A9:$'4. Lambda'.CD24

VLOOKUP( D62; $'4. Lambda'.A9:$'4. Lambda'.C

Row 2
5Cr
 D7:CD8

5 6 7 8 9 10 11 12 13
-494 -480 -466 -452 -438 -424 -411 -397 -383
5 6 7 8 9 10 11 12 13
- - 9.0E-06 9.1E-06 9.2E-06 9.3E-06 9.4E-06 9.5E-06 9.7E-06
- - 8.4E-06 8.5E-06 8.6E-06 8.7E-06 8.8E-06 9.0E-06 9.2E-06
- - 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05
- - 7.7E-06 7.8E-06 7.8E-06 7.9E-06 8.0E-06 8.1E-06 8.3E-06
- - - - - - - - -
9.9E-06 1.0E-05 1.0E-05 1.1E-05 1.1E-05 1.1E-05 1.2E-05
8.5E-06 8.8E-06 9.0E-06 9.2E-06 9.5E-06 9.8E-06 9.9E-06
1.3E-05 1.4E-05 1.4E-05 1.4E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05
- - 1.8E-05 1.8E-05 1.8E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05
- - - - - - - - -
- - 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.6E-05
- - 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05
- - 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.3E-05
- - - - - - - - -
- - - - - - - - -
- - - - - - - 8.4E-06 8.6E-06

mbda'.A9:$'4. Lambda'.CD24;D64) Col_A = HLOOKUP(D61; $'4. Lambda'.D7:$'4. Lambda'.CD8; 2)

t D7:CD8
4. Lambda'.A9:$'4. Lambda'.CD24 ; D64) 38
Col_A = 43
A9:CD24 for t = 34
 14 15 16 17 18 19 20 21 22
-369 -355 -341 -327 -313 -299 -286 -272 -258
14 15 16 17 18 19 20 21 22
9.9E-06 1.0E-05 1.0E-05 1.0E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
9.3E-06 9.5E-06 9.5E-06 9.7E-06 9.9E-06 9.9E-06 9.9E-06 1.0E-05 9.8E-06
1.5E-05 1.5E-05 1.5E-05 1.6E-05 1.6E-05 1.5E-05 1.5E-05 1.5E-05 1.6E-05
8.5E-06 8.5E-06 8.6E-06 8.8E-06 9.0E-06 9.0E-06 9.0E-06 9.0E-06 9.0E-06
- - - - - - - - -
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.5E-05
1.0E-05 1.0E-05 1.0E-05 1.0E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.7E-05 1.7E-05 1.7E-05
2.0E-05 2.0E-05 2.0E-05 2.0E-05 2.1E-05 2.1E-05 2.1E-05 2.1E-05 2.1E-05
- - - - - - - - -
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.7E-05 2.0E-05 1.7E-05 1.6E-05 1.7E-05
1.5E-05 1.5E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.3E-05 1.3E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05
- - - - - - - - -
- - - - - - - - -
8.8E-06 8.9E-06 9.2E-06 9.4E-06 9.6E-06 9.8E-06 9.9E-06 7.7E-06 1.1E-05

a'.D7:$'4. Lambda'.CD8; 2)
Row 2
 23 24 25 26 27 28 29 30 31
-247 -230 -216 -202 -188 -174 -161 -147 -133
23 24 25 26 27 28 29 30 31
1.1E-05 1.2E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.2E-05 1.2E-05 1.2E-05
1.0E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
1.6E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
9.4E-06 1.0E-05 9.8E-06 9.9E-06 9.9E-06 9.9E-06 1.0E-05 1.0E-05 1.0E-05
- 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.5E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05
1.1E-05 1.2E-05 1.1E-05 1.1E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
2.2E-05 2.3E-05 2.3E-05 2.3E-05 2.3E-05 2.3E-05 2.3E-05 2.4E-05 2.4E-05
- 1.1E-05 1.0E-05 1.0E-05 1.0E-05 1.0E-05 1.0E-05 1.1E-05 1.1E-05
1.7E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
1.6E-05 1.8E-05 1.7E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
1.5E-05 1.6E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.6E-05 1.6E-05
- 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.5E-05 1.5E-05
- 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.4E-05
1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
 Table C-1
Thermal expansion coefficient " l " [m/(m*K)] for me
Temperatura °C
32 33 34 35 36 37 38 39 40
-119 -105 -91 -77 -63 -49 -36 -22 -8
32 33 34 35 36 37 38 39 40
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.3E-05 1.3E-05
1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.2E-05 1.2E-05 1.2E-05
1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
1.0E-05 1.0E-05 1.0E-05 1.0E-05 1.0E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.7E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
2.4E-05 2.4E-05 2.4E-05 2.4E-05 2.5E-05 2.5E-05 2.5E-05 2.5E-05 2.5E-05
1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.9E-05 1.9E-05 1.9E-05
1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 - - - -
1.5E-05 1.5E-05 1.5E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05
1.1E-05 1.1E-05 1.1E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
 Table C-1
sion coefficient " l " [m/(m*K)] for metals
Temperatura °C
41 42 43 44 45 46 47 48 49
6 20 34 48 62 76 89 103 117
41 42 43 44 45 46 47 48 49
1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.4E-05
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05 1.1E-05
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05
1.8E-05 1.8E-05 1.8E-05 1.7E-05 - - - - -
2.5E-05 2.5E-05 2.5E-05 2.6E-05 - - - - -
1.1E-05 1.1E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05
1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 2.0E-05 2.0E-05 2.0E-05
- - - - - - - - -
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05
1.2E-05 1.2E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05
50 51 52 53 54 55 56 57 58
131 145 159 173 187 201 214 228 242
50 51 52 53 54 55 56 57 58
1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05
1.2E-05 1.2E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05
1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
1.1E-05 1.1E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05
1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.6E-05 1.7E-05 1.7E-05
1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.4E-05
- - - - - - - - -
- - - - - - - - -
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05
1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05
2.0E-05 2.0E-05 2.0E-05 2.0E-05 2.0E-05 2.0E-05 2.1E-05 2.1E-05 2.1E-05
- - - - - - - - -
1.6E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
1.4E-05 1.5E-05 1.5E-05 - - - - - -
1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05
59 60 61 62 63 64 65 66 67
256 270 284 298 312 326 339 353 367
59 60 61 62 63 64 65 66 67
1.4E-05 1.4E-05 1.4E-05 1.4E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05
1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05
1.8E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.6E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
1.4E-05 1.4E-05 - - - - - - -
- - - - - - - - -
- - - - - - - - -
1.3E-05 1.3E-05 - - - - - - -
1.9E-05 1.9E-05 1.9E-05 2.0E-05 2.0E-05 2.0E-05 - - -
2.1E-05 2.1E-05 2.1E-05 2.1E-05 2.1E-05 2.1E-05 - - -
- - - - - - - - -
1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
- - - - - - - - -
1.3E-05 1.3E-05 - - - - - - -
68 69 70 71 72 73 74 75 76
381 395 409 423 437 451 464 478 492
68 69 70 71 72 73 74 75 76
1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05 1.5E-05
1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.3E-05 1.4E-05 1.4E-05 1.4E-05 1.4E-05
1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05 1.9E-05
1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05 1.2E-05
1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.7E-05
1.7E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
- - - - - - - - -
- - - - - - - - -
- - - - - - - - -
- - - - - - - - -
- - - - - - - - -
- - - - - - - - -
- - - - - - - - -
1.7E-05 1.7E-05 1.7E-05 1.7E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05 1.8E-05
- - - - - - - - -
- - - - - - - - -
77 78 79 80
506 520 534 548
77 78 79 80
- - - -
- - - -
1.9E-05 1.9E-05 1.9E-05 1.9E-05
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
1.8E-05 1.8E-05 1.8E-05 1.8E-05
- - - -
- - - -
 Table B. Young Modulus of Elasticity E
Metal
1 2 3 4 5 6
1 -200 -129 -73 21 93
1 2 3 4 5 6
1 Carbon steel C <= 0.3% 2.2E+11 2.1E+11 2.1E+11 2.0E+11 2.0E+11
2 Carbon steel C => 0.3% 2.2E+11 2.1E+11 2.1E+11 2.0E+11 2.0E+11
3 Carbon-moly steels 2.1E+11 2.1E+11 2.1E+11 2.0E+11 2.0E+11
4 Nickel steels Ni 2% - 9% 2.0E+11 2.0E+11 2.0E+11 1.9E+11 1.9E+11
5 Cr-Mo steels Cr 1/2% - 2% 2.2E+11 2.1E+11 2.1E+11 2.0E+11 2.0E+11
6 Cr-Mo steels Cr 2 1/4% - 3% 2.2E+11 2.2E+11 2.2E+11 2.1E+11 2.1E+11
7 Cr-Mo steels Cr 5% - 9% 2.3E+11 2.2E+11 2.2E+11 2.1E+11 2.1E+11
8 Chromium steels Cr 12%, 17%, 27% 2.2E+11 2.1E+11 2.1E+11 2.0E+11 2.0E+11
9 Austenitic steels (TP304, 310, 316, 321, 347) 2.1E+11 2.0E+11 2.0E+11 2.0E+11 1.9E+11

Cast iron
Gray cast iron 1.3E+01 1.3E+01

http://www.engineeringtoolbox.com/young-modulus-d_773.html
Mpsi = 6.9E+09 Pa
Young Modulus of Elasticity E [Pa]
Temperature (oC)
7 8 9 10 11 12 13 14 15 16
149 204 260 316 371 427 482 538 593 649
7 8 9 10 11 12 13 14 15 16 3
2.0E+11 1.9E+11 1.9E+11 1.8E+11 1.8E+11 1.7E+11 1.5E+11 1.4E+11 1.2E+11 "N/A"
1.9E+11 1.9E+11 1.9E+11 1.8E+11 1.7E+11 1.7E+11 1.5E+11 1.4E+11 1.2E+11 1.1E+11
1.9E+11 1.9E+11 1.9E+11 1.8E+11 1.7E+11 1.6E+11 1.5E+11 1.4E+11 1.2E+11 1.1E+11
1.8E+11 1.8E+11 1.8E+11 1.7E+11 1.7E+11 1.6E+11 "N/A" "N/A" "N/A" "N/A"
2.0E+11 1.9E+11 1.9E+11 1.9E+11 1.8E+11 1.8E+11 1.7E+11 1.6E+11 1.6E+11 1.5E+11
2.0E+11 2.0E+11 2.0E+11 1.9E+11 1.9E+11 1.8E+11 1.8E+11 1.7E+11 1.6E+11 1.6E+11
2.0E+11 2.0E+11 2.0E+11 1.9E+11 1.9E+11 1.8E+11 1.7E+11 1.6E+11 1.4E+11 1.3E+11
1.9E+11 1.9E+11 1.8E+11 1.8E+11 1.8E+11 1.7E+11 1.6E+11 1.5E+11 1.3E+11 1.1E+11
1.9E+11 1.8E+11 1.8E+11 1.7E+11 1.7E+11 1.7E+11 1.6E+11 1.6E+11 1.5E+11 1.5E+11

Cast iron
1.3E+01 1.3E+01 1.2E+01 1.2E+01 1.1E+01 1.0E+01
 Temperature

Metal -200 -129 -73 21 93 149 204

4
Carbon steel C <= 0.3% 31.4 30.8 30.2 29.5 28.8 28.3 27.7
Carbon steel C => 0.3% 31.2 30.6 30 29.3 28.6 28.1 27.5
Carbon-moly steels 31.1 30.5 29.9 29.2 28.5 28 27.4
Nickel steels Ni 2% - 9% 29.6 29.1 28.5 27.8 27.1 26.7 26.1
Cr-Mo steels Cr 1/2% - 2% 31.6 31 30.4 29.7 29 28.5 27.9
Cr-Mo steels Cr 2 1/4% - 3% 32.6 32 31.4 30.6 29.8 29.4 28.8
Cr-Mo steels Cr 5% - 9% 32.9 32.3 31.7 30.9 30.1 29.7 29
Chromium steels Cr 12%,
17%, 27% 31.2 30.7 30.1 29.2 28.5 27.9 27.3
Austenitic steels (TP304,
310, 316, 321, 347) 30.3 29.7 29.1 28.3 27.6 27 26.5

Cast iron
Gray cast iron 13.4 13.2 12.9 12.6
 Temperature (oC)

260 316 371 427 482 538 593 649

4 5 6
27.3 26.7 25.5 24.2 22.4 20.4 18
27.1 26.5 25.3 24 22.2 20.2 17.9 15.4
27 26.4 25.3 23.9 22.2 20.1 17.8 15.3
25.7 25.2 24.6 23
27.5 26.9 26.3 25.5 24.8 23.9 23 21.8
28.3 27.7 27.1 26.3 25.6 24.6 23.7 22.5
28.6 28 27.3 26.1 24.7 22.7 20.4 18.2
26.7 26.1 25.6 24.7 23.2 21.5 19.1 16.6
25.8 25.3 24.8 24.1 23.5 22.8 22.1 21.2

st iron
12.2 11.7 11 10.2
7 8 9
http://pointing.spiraxsarco.com/resources/steam-engineering-tutorials/steam-distribution/pipe-expansion-and-support.asp

For expansion "

pipe nominal diameter "dn" (in),
Spiraxsarco graph provides an
expansionloop width "W" (m).

DL =
dn =
Estimated value from Fig. 10.4
W=

spiraxsarco. Expansion loop capacity

http://pointing.spiraxsarco.com/resources/steam-engineering-tutorials/steam-distribution/pipe-expansion-and-support.asp

Example 10.4.2

Using Figure 10.4.1. Find the approximate expansion from 15°C, of 100 metres of carbon steel pipework used to distribute steam at 26

Temperature difference is 265 - 15°C = 250°C.

Where the diagonal temperature difference line of 250°C cuts the horizontal pipe length line at 100 m, drop a vertical line down. For t

Fig. 10.4.1 A chart showing the expansion in various steel pipe lengths at various temperature differences
Table 10.4.2 Temperature of saturated steam
pipe-expansion-and-support.asp

r expansion "DL" (mm), and a

pe nominal diameter "dn" (in),
iraxsarco graph provides an
pansionloop width "W" (m).

90 mm
273 mm
timated value from Fig. 10.4
2.55 m

raxsarco. Expansion loop capacity

ansion-and-support.asp

pework used to distribute steam at 265°C.

0 m, drop a vertical line down. For this example an approximate expansion of 330 mm is indicated.
http://static.victaulic.com/assets/uploads/literature/26.02-SPA.pdf
Vitaulic equation for an expansion loop

1988 ASHRAE Handbook, EQUIPM

3 E  d  f
H  0 .4 

5W =
W=

H=
H=
H=

3  E  d  f to
L  0.378 
 max
Equation deducted in sheet 2
88 ASHRAE Handbook, EQUIPMENT E: Elasticity module of mater
d: exterior pipe diameter
3  E  d  f tot ftot: total pipe expansion
H  0.4  S: Allowable stress of materi

L H=
L/5

2*W
2*L/5
0.4 * L

3  E  d  f tot
 0.378 
 max
quation deducted in sheet 2
Elasticity module of material
exterior pipe diameter
t: total pipe expansion
Allowable stress of material
http://www.engineeringtoolbox.com/pipes-temperature-expansion-coefficients-d_48.html

Temperature Expansion Coefficients for some common Piping Materials

Expansion coefficients for some common materials used for pipes and t
Expansion coefficients that can be used to calculate temperature expansion of pipes and tubes - are indicated in the table

Expansion Coefficients

Material
10-6 in/in 10-6 m/m
o
F o
C

Aluminum 12.8 23.1

Carbon Steel 6.5 11.7
Cast Iron 5.9 10.6
Copper 9.3 16.8
Stainless Steel 9.9 17.8
ABS Acrylonitrile butadiene styrene 35 63
HDPE High density polyethylene 67 120
PE Polyethylene 83 150
CPVC Chlorinated polyvinyl chloride 44 79
PVC Polyvinyl chloride 28 50.4

http://www.engineeringtoolbox.com/young-modulus-d_417.html

Ultimate
Yield
Tensile Modulus Tensile
Strength
Strength
(Young's Modulus,
Modulus of - Su - - Sy -
Elasticity)

Material (106 N/m2, (106 N/m2,

-E-
MPa) MPa)

(109 N/m2,
(106  psi)
GPa)

Polyvinylchloride (PVC) 2.4 - 4.1

E=
ABS plastics 1.4 - 3.1 40
Acetals 2.8 65
Acrylic 3.2 70
Aluminum Bronze 120
Aluminum 10 69 110 95
Aluminum Alloys 10.2
Antimony 11.3
Aramid 70 - 112
Beryllium (Be) 42  287
Beryllium Copper 18
Bismuth 4.6
170
Bone, compact 18 (compressi
on)
Bone, spongy 76
Boron 3100
Brass 102 - 125 250
Brass, Naval 100
Bronze 96 - 120
CAB 0.8
Cadmium 4.6
Carbon Fiber Reinforced Plastic 150
Carbon nanotube, single-walled 1000+
Cast Iron 4.5% C, ASTM A-48 170
Cellulose,  cotton, wood pulp and
80 - 240
regenerated
Cellulose acetate, molded dic-58
Cellulose acetate, sheet 30 - 52
Cellulose nitrate, celluloid 50
Chlorinated polyether 1.1 39
Chlorinated PVC (CPVC) 2.9
Chromium 36
Cobalt 30
Concrete 17
40
Concrete, High Strength (compression) 30 (compressi
on)
Copper 17 117 220 70
Diamond (C) 1220
50
Douglas fir Wood 13 (compressi
on)
Epoxy resins 03-feb 26 - 85
Fiberboard, Medium Density 4
Flax fiber 58
50
Glass 50 - 90 (compressi
on)
Glass reinforced polyester matrix 17
Gold 10.8  74
Granite 52
Graphene 1000
Grey Cast Iron 130
Hemp fiber 35
Inconel 31
Iridium 75
Iron 28.5  210
Lead 2
Magnesium metal (Mg) 6.4 45
Manganese 23
Marble 15
MDF - Medium-density fiberboard 4
Mercury
Molybdenum (Mo) 40  329
Monel Metal 26
Nickel 31  170
Nickel Silver 18.5
Nickel Steel 29
Niobium (Columbium) 15
Nylon-6 02-abr 45 - 90 45
Nylon-66 60 - 80
Oak Wood (along grain) 11
Osmium (Os) 80  550
Phenolic cast resins 33 - 59
Phenol-formaldehyde molding compounds 45 - 52
Phosphor Bronze 116
Pine Wood (along grain) 9 40
Platinum 21.3
Plutonium 14  97
Polyacrylonitrile, fibers 200
Polybenzoxazole 3.5
Polycarbonates 2.6 52 - 62
Polyethylene HDPE (high density) 0.8 15
Polyethylene Terephthalate, PET 2 - 2.7 55
Polyamide 2.5 85
Polyisoprene, hard rubber 39
Polymethylmethacrylate (PMMA) 2.4 - 3.4
Polyimide aromatics 3.1 68
Polypropylene, PP 1.5 - 2 28 - 36
Polystyrene, PS 3 - 3.5 30 - 100
Polytehylene, LDPE (low density) 0.11 - 0.45
Polytetrafluoroethylene (PTFE) 0.4
Polyurethane cast liquid oct-20
Polyurethane elastomer 29  - 55
Polyvinylchloride (PVC) 2.4 - 4.1
Potassium
Rhodium 42
Rubber, small strain 0.01 - 0.1
Sapphire 435
Selenium 8.4
Silicon 16  130 - 185
Silicon Carbide 450 3440
Silver 10.5
Sodium
Steel, High Strength Alloy ASTM A-514 760 690
Steel, stainless AISI 302 180 860 502
Steel, Structural ASTM-A36 200 400 250
Tantalum 27
Polytetrafluoroethylene (PTFE) 0.5
Thorium 8.5
Tin 47
Titanium 16
Titanium Alloy 105 - 120 900 730
Tooth enamel 83
Tungsten (W) 400 - 410
Tungsten Carbide (WC) 450 - 650
Uranium 24  170
Vanadium 19
Wrought Iron 190 - 210
Zinc 12

#VALUE!

Thermoplastics - Physical Properties

Physical properties of some thermoplastics like ABS, PVC, CPVC, PE,

Typical properties of some common thermoplastics:

Tensile
Yield Tensile Modulus
CoefficientsThermal
of Conductivity
Specific Heat
Strength
Thermoplastic Specific Gravity (Btu in /h
(103 psi) (103 psi) Linear Expansion (Btu/lb oF)
ft2 oF)
(106 in/in
o
F)
ABS 1.08 7 340 60 1.35 0.34
PVC 1.4 8 410 30 1.1 0.25
CPVC 1.54 8 420 35 1 0.2
PE 0.95 3.2 120 90 3.2 0.55
PEX 0.94 2.8 . 90 3.2 0.55
PB 0.92 4.2 55 72 1.5 0.45
PVDF 1.76 7 220 70 1.5 0.29

1 psi (lb/in2) = 6,894.8 Pa (N/m2) - Note! You can use the pressure unit converter on this page to switch to Pa (N/m
1 (Btu/lb oF) = 4,186.8 (J/kg K) = 1 (kcal/kg oC)
ed for pipes and tubes - like aluminum, carbon steel, cast iron, PVC, HDPE and
es - are indicated in the table below:

THERMAL
http://www.harvel.com/piping-systems/gf-harvel-pvc-industrial-pipe

Coefficient of Linear Expansion

Coefficient
ASTM
of Linear in/in/°F 2.9 x 10-5 2.8 x 10-5
D696
Expansion
l= 2.8E-05 in / (in / ºF)
l= 5.04E-05 m/(m*ªC)

http://www.harvel.com/piping-systems/gf-harvel-pvc-industrial-pipe

Tensile Modulus of Elasticity @ 73°F, for PVC

Tensile
Modulus
ASTM
of PSI 420,000 430,000
D638
Elasticity
@ 73°F
E= 4.3E+05. psi
E= 3.0E+03. Mpa
E= 3E+09, Pa
PVC, CPVC, PE, PEX, PB and PVDF

Maximum
Temperat
ure Limit
(oF/oC)

180/80
150/65 s = 8 kpsi
210/100 s = 8000 psi
160/70 s = 5.52E+07 Pa
210/100
210/100
300/150

age to switch to Pa (N/m 2) units.

PVC, HDPE and more
U.S. Army Corps of Engineers

[8]
Pipe material design stress
sdes = 103
Material elasticity modulus
E= 1.92E+05

L0 = 145
dext = 200
top = 90
t0 = 4.4

Temperature difference
Dt = top -t0
top = 90
t0 = 4.4
Dt = 85.6

Linear expansion
DL = L0 * a * Dt
L0 = 145
a = 1.17E-05
Dt = 85.6
DL = 0.1452

H= 0.4 * ( 3 * E * d
E= 1.92E+05
dext = 0.2
DL = 0.1452
sallow = 103
H= 5.098
1988 ASHRAE Handbook, EQUIPMENT

H= 0.4 * ( 3 * E * dext * DL / salow)^0.5

erial design stress
MPa
elasticity modulus
MPa

m
mm Thermal expansion coefficient
ºC a = 1.17E-05 m / (m * K)
ºC Pipe material design stress
sallow = 103 MPa
Material elasticity modulus
E= 1.92E+05 MPa

re difference

ºC
ºC
K

L 0 * a * Dt
m
m / (m * K)
K
m

0.4 * ( 3 * E * dext * DL / salow)^0.5 The derived equation for the loop height is
MPa Height "H"
MPa H = 0.378*( (3 * E * de * DL) / (sallow) )^0.5
m
MPa
m
Cantilever beam, concentrated load at free end

y= P * L³ / (3*E*I)
 Select data with Combo Box form control
Required is to obtain the value of the
1 Z-Factor for a given seismic zone, selec
using the Drop-down list.

Seismic zone factor Z

2 Seismic zone
1
2A
2B
Insert 3
It appears the Forms control box 4

Select a seismic zone

3
Corresponding Z-Factor
3 Select: Combo Box (Form Control) Z=

Note. If it is not required the use of a

Drop-down list, the use of the V-lookup
function is a much more shorter way.

Z=
Z=
4 Draw a box

5 Right clik box

6 Click formar control

The Format Control window appears

 Application example

2
Seismic zone factor Z
Seismic zone Factor Z
1 0.075
2A 0.15
2B 0.2
3 0.3
4 0.4

(repetead)
4 Draw a box
5 Rigth click the box
6 Format control
7 Input the range and
8 define a cell to place the link
9 OK

7
8

10 10 Click the selection box

to select a zone

Obtain a workable number (Z-value) corresponding to the selected zone

Insert function Index
11

12 OK

Select the first argument row

13

14 OK

The function arguments window appears

In the Functions arguments window, input required data

15
16
17

18

Z= INDEX(E66:F70,E63,2)
Z= 0.15
 rev.cjc.01.08.2018

to obtain the value of the

a given seismic zone, selected
rop-down list.

Seismic zone factor Z

Factor Z
0.075
0.15
0.2
0.3
0.4

Select a seismic zone

3
Corresponding Z-Factor
0.2

not required the use of a

list, the use of the V-lookup
a much more shorter way.

VLOOKUP(K14,K12:L16,2)
0.2
[1] Elementos de resistencia de materiales
S. Timoshenko, D. H. Young
Ed. Limusa, 1996

[2]

[3]

[4] http://static.victaulic.com/assets/uploads/literature/26.02-SPA.pdf

[5] http://www.spiraxsarco.com/resources/steam-engineering-tutorials/steam-distribution/pipe-expansion-and-support.asp

[5] F(Simple drive):\Libreria\Piping\Piping Handbook (7th Edition)

[6] http://www.engineeringtoolbox.com/young-modulus-d_773.html
 www.piping-tools.net
Expansion_loop.xlsm

[7] http://www.awc.org/pdf/codes-standards/publications/design-aids/AWC-DA6-BeamFormulas-0710.pdf

[8]

http://www.publications.usace.army.mil/Portals/76/Publications/EngineerManuals/EM_1110-1-4008.pdf
 Microsoft Editor
ecuaciones 3

Microsoft Edi
ecuaciones

Microsoft Edit
ecuaciones

ion/pipe-expansion-and-support.asp
A6-BeamFormulas-0710.pdf

U.S. Army Corps of Engineers

anuals/EM_1110-1-4008.pdf
 Microsoft Editor de
ecuaciones 3.0

Microsoft Editor de
ecuaciones 3.0

Microsoft Editor de
ecuaciones 3.0

Microsoft Editor de
ecuaciones 3.0

Microsoft Editor de
ecuaciones 3.0

Microsoft Editor de
ecuaciones 3.0

Microsoft Editor de
ecuaciones 3.0