Lecture 2: Ray theory transmission in optical fibers

•  Nature of light
•  Ray optics
•  Refractive indices
•  Snell’s Law
•  Total internal reflection
•  Acceptance angle
•  Numerical Aperture
•  Optical fiber structures

Reading: Senior 2.1 – 2.2

Keiser 2.1 – 2.2
Part of the lecture materials were adopted from powerpoint slides of Gerd Keiser’s book 2010,
Copyright © The McGraw-Hill Companies, Inc.
1
The nature of light

3
 Light as waves, rays and photons
•  Light is an electromagnetic wave.

•  While light is a wave, it nevertheless travels along straight

lines or rays, enabling us to analyze simple optical
components (e.g. lenses and mirrors) and instruments in terms
of geometrical optics.

•  Light is also a stream of photons, discrete particles carrying

packets of energy and momentum.

4
 Ray Optics or Geometrical Optics
Wavelength λ << size of the optical component
λ

ray

wavefront

•  In many applications of interest the wavelength λ of light is

short compared with the relevant length scales of the optical
components or system (e.g. mirrors, prisms, lenses).
•  This branch of optics is referred to as Ray optics or
Geometrical Optics, where energy of light is propagated along
rays.
•  The rays are perpendicular to the wavefronts. 7
Ray Optics: basic laws

ni sin θi = nt sin θt
8
 Snell’s Law
When a ray is incident on the interface between two dielectrics of
different refractive indices (e.g. glass-air), reflection and refraction
occur.
normal

low index n2 θ2 refraction

(air) Plane of incidence ≡ plane that
comprises the incident ray and
high index n1 the plane normal
(glass) θ1 θ1
reflection
The angle of incidence θ1 and the angle of refraction θ2 are related to
each other, and to the refractive indices of the dielectrics by
Snell’s law of refraction:
n1 sin θ1 = n2 sin θ2 9
 Refractive index

•  In any dielectric medium, the speed of light becomes

v = c/n

The factor n is the index of refraction (or refractive index) of the medium.

e.g. For air and gases, v ~ c, so that n ~ 1. At optic frequencies, the

refractive index of water is 1.33.

e.g. Glass has many compositions, each with a slightly different n. An

approximate refractive index of 1.5 is representative for the silica
glasses used in fibers; more precise values for these glasses lie between
~1.45 and ~1.48.
10
 Index of refraction for some materials
Air 1.0
Water 1.33
Magnesium fluoride 1.38
Fused silica (SiO2) 1.46
Sapphire (Al2O3) 1.8
Lithium niobate (LiNbO3) 2.25
Indium phosphide (InP) 3.21
Gallium arsenide (GaAs) 3.35
Silicon (Si)
3.48
Indium gallium arsenide phosphide (InGaAsP) 3.51
Aluminum gallium arsenide (AlGaAs) 3.6
Germanium (Ge) 4.0
*The index varies with a number of parameters, such as wavelength and temperature.
11
 Critical angle
For n1 > n2, the angle of refraction θ2 is always greater than the
angle of incidence θ1.

•  When the angle of refraction θ2 is 90o, the refracted ray emerges

parallel to the interface between the media.
This is the limiting case of refraction and the angle of incidence is
known as the critical angle θc.

low index n2 θ2
(air) refraction
sin θc = n2 / n1
high index n1
(glass) θc θc
reflection
12
 Total internal reflection
•  At angles of incidence θ > θc, the light is totally reflected back into
the incidence higher refractive index medium. This is known as total
internal reflection.
normal

low index n2
(air)

high index n1
(glass) θ1 > θc TIR

e.g. n1 = 1.44, n2 = 1, then θc = sin-1(1/1.44) = 44o

Total internal reflection: θ1 > θc 13

 Light ray guiding condition
•  Light ray that satisfies total internal reflection at the interface of the
higher refractive index core and the lower refractive index cladding can
be guided along an optical fiber.

cladding n2
core n1 θ

θ

e.g. Under what condition will light be trapped inside the fiber core?
n1 = 1.46; n2 = 1.44
θ > θc

θc = sin-1 (n2/n1) = sin-1 (1.44/1.46) = 80.5o

14
 Optical fiber structures
•  A typical bare fiber consists of a core, a cladding and a polymer
jacket (buffer coating).
typically
250 µm
including
jacket for
glass fibers

•  The polymer coating is the first line of mechanical protection.

•  The coating also reduces the internal reflection at the cladding, so

light is only guided by the core.
*In Lab1, we shall learn how to strip off the jacket to expose the
cladding. This is necessary in order to “cleave” the fiber for a smooth
15
end face for light coupling.
 Silica optical fibers

•  Both the core and the cladding are made from a type of glass known
as silica (SiO2) which is almost transparent in the visible and near-IR.

•  In the case that the refractive index changes in a “step” between the
core and the cladding. This fiber structure is known as step-index fiber.

•  The higher core refractive index (~ 0.3% higher) is typically obtained

by doping the silica core with germanium dioxide (GeO2).

*In Lab 1, we should be able to see the step boundary between the
core and the cladding, by end-illuminating the fiber and imaging the
output-end cross-section using a microscope.
16
 Numerical aperture
•  An important characteristic of an optic system is its ability to collect
light incident over a wide range of angles.
f f

The numerical aperture (NA) is defined as:

NA = no sin θ

where no is the refractive index of the medium between the lens and the
image plane (e.g. a photodetector) and θ is the maximum acceptance angle.
17
•  The definition of numerical aperture applies to all light-collecting
systems, including optical fibers.

e.g. Light rays incident at angles outside the collection cone for a fiber
will not propagate along the fiber (instead will attenuate rapidly).

•  The numerical aperture is often measured in air, no = 1

NA = sin θ

•  A low NA indicates a small acceptance angle.

⇒ Light coupling to a low-NA optical system (e.g. fiber) is more

difficult (alignment is more sensitive) and less efficient (some of the
rays are outside the acceptance angle) than is coupling to a high-NA
optical system.
18
 Acceptance angle
•  Only rays with a sufficiently shallow grazing angle (i.e. with an
angle to the normal greater than θc) at the core-cladding interface
are transmitted by total internal reflection.

αc θc
θa n1
A na n2

•  Ray A incident at the critical angle θc at the core-cladding interface

enters the fiber core at an angle θa to the fiber axis, and is refracted
at the air-core interface.
19
 θ < θa αc θc
θa n1
na n2

θ > θa αc θc
θa n1
na n2

•  Any rays which are incident into the fiber core at an angle > θa
have an incident angle less than θc at the core-cladding interface.

These rays will NOT be totally internal reflected, thus eventually loss
to radiation (at the cladding-jacket interface).
20
•  Light rays will be confined inside the fiber core if it is input-coupled
at the fiber core end-face within the acceptance angle θa.

e.g. What is the fiber acceptance angle when n1 = 1.46 and

n2 = 1.44?

θc = sin-1 (n2/n1) = 80.5o => αc = 90o - θc = 9.5o

using sin θa = n1 sin αc (taking na = 1)

θa = sin-1 (n1 sin αc) = sin-1 (1.46 sin 9.5o) ~ 14o

=> the acceptance angle θa ~ 14o

21
 Fiber numerical aperture

In fiber optics, we describe the fiber acceptance angle using

Numerical Aperture (NA):

NA = na sin θa = sin θa = (n12 - n22)1/2

αc θc
θa n1
na n2

•  We can relate the acceptance angle θa and the refractive indices of the
core n1, cladding n2 and air na. 22
•  Assuming the end face at the fiber core is flat and normal to the
fiber axis (when the fiber has a “nice” cleave), we consider the
refraction at the air-core interface using Snell’s law:

At θa: na sin θa = n1 sin αc

launching the light from air: sin θa = n1 sin αc

(na ~ 1)
= n1 cos θc
= n1 (1 - sin2θc)1/2
= n1 (1 - n22/n12)1/2

= (n12 - n22)1/2
23
•  Fiber NA therefore characterizes the fiber’s ability to gather light
from a source and guide the light.

e.g. What is the fiber numerical aperture when n1 = 1.46 and

n2 = 1.44?

NA = sin θa = (1.462 - 1.442)1/2 = 0.24

•  It is a common practice to define a relative refractive index Δ as:

Δ = (n1 - n2) / n1

(n1 ~ n2) => NA = n1 (2Δ)1/2

i.e. Fiber NA only depends on n1 and Δ. 24

 Lens coupling to fiber end faces
Microscope
objective lens

collimated
laser beam θa

few mm focal length

θa
θa

focusing “fiber under test” collecting

objective lens objective lens

•  By measuring the output couple ray cone angle, we can measure the fiber
acceptance angle. (This is like part of Lab 1 but without using lenses.) 25
 Large-NA fibers?
•  Developing ways for fiber to collect light efficiently was an
important early step in developing practical fiber optic
communications (particularly in the 1970s)

•  It seems logical to have optical fibers with NA as large as possible …

with as large Δ as possible … in order to couple maximum amount of
light into the fiber.

•  Soon, we will find out that such large-NA fibers tend to be

“multimode” and are unsuitable for high-speed communications
because of a limitation known as modal dispersion.

•  Relatively small-NA fibers are therefore used for high-speed optical

communication systems. 26
 Typical fiber NA
•  Silica fibers for long-haul transmission are designed to
have numerical apertures from about 0.1 to 0.3.

The low NA makes coupling efficiency tend to be poor, but

turns out to improve the fiber’s bandwidth! (details later)

•  Plastic, rather than glass, fibers are available for short-haul

communications (e.g. within an automobile). These fibers are restricted
to short lengths because of the relatively high attenuation in plastic
materials.

Plastic optical fibers (POFs) are designed to have high numerical

apertures (typically, 0.4 – 0.5) to improve coupling efficiency, and so
partially offset the high propagation losses and also enable alignment
tolerance. 27
 Limitation of ray optics
•  For smaller fiber diameters that are only few times of the wavelength,
geometrical optics approach becomes inadequate. This is because ray
optics only describes the direction a plane wave component takes
in the fiber, but does not take into account interference among such
components.

•  When interference phenomena are considered it is found that only rays

with certain discrete characteristics propagate in the fiber core.

•  Thus the fiber will only support a discrete number of guided modes.

•  This becomes critical in small core diameter fibers which only support
one (singlemode) or a few modes (multimode). Electromagnetic theory
must be applied in this case. 28
Op#cal  Fiber  Type  Comparisons  
Cladding
Cladding

2a
2a

Core
Core

n1
n1

n2

Step-index fiber

n1
n1

n2

Graded-index fiber

(a) Basic fiber types
(b) Sample tailored profiles

29  
Numerical  Aperture  Example  

30