Scribd
Upload
67 views

Schematic

1. The document discusses using a momentary membrane switch to reset a PIC microcontroller and select which waveform from a WaveBank will be activated. 2. It provides instructions for mounting an op-amp in an 8-pin socket to output a 5V peak-to-peak signal with limited bandwidth, or without the op-amp to output an 8.63V peak-to-peak signal. 3. A diagram shows the circuit used for an arbitrary function generator or smart probe head, including the op-amp, resistors, and DIP switch to select the output vector.

Uploaded by

David Torres
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
67 views

Schematic

1. The document discusses using a momentary membrane switch to reset a PIC microcontroller and select which waveform from a WaveBank will be activated. 2. It provides instructions for mounting an op-amp in an 8-pin socket to output a 5V peak-to-peak signal with limited bandwidth, or without the op-amp to output an 8.63V peak-to-peak signal. 3. A diagram shows the circuit used for an arbitrary function generator or smart probe head, including the op-amp, resistors, and DIP switch to select the output vector.

Uploaded by

David Torres
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

1 2 3 4 5 6 7 8 9

F Momentary Membrane switch resets the PIC WaveBank Vector F

This will force WaveBank PIC to vector to 4 Bit binary vector selects which
a location selected by the DIP switch. WaveLoop in WavePOD will be
activated when the PIC is RESET

Mount OP AMP in 8 PIN 300mil IC Socket.

Output with OP-AMP is 5.00V p-p.


The Bandwidth is limited by the OP-AMP characteristics.

Output without OP-AMP is 8.63V p-p.


The Bandwidth is limited by the 3K6 resistor and load capacitance.

VCC

VCC

E E
R12

10K VCC

RESET
R5

4
U3A
TL072 10K Switch
2
R2 R1 R4 R3
1
3 C6 10K 10K 10K 10K

To use as an Arbitrary Function Generator Vector


1nF
plug directly into BitScope. 1 8

8
R10 1K8 2 7
To use as a Smart Probe Head, plug 3 6
into the Smart Cable Assembly. 4 5
D D
SW-DIP4
U3B
TL072
6
GND
7
5

Y1

R11 1K8

20MHz
C1 C2
U1
22pF 22pF
1 18
RA2 RA1
R8 R9 GND GND
2 17
VCC RA3 RA0
3K6 3K6
1 +10V P5
C R6 3 16 C
1 RA4 CLKI
+5 Logic

13
14 1K8
PIC
U2 4 15
2 MCLR CLKO
2 CHAN A
15 4 5
Iout msb-B1 5 14

+Vs
3 6 VSS VDD VCC
3 CHAN B
16F84
BitScope Pod

B2
16 2 7
Iout B3 6 13
IO-1 4 8 RB0 RB7
B4
17 9 C5
B5 7 12
IO-0 5 14 10 RB1 RB6
5 Logic 7 Vrf(+) B6
18 11 GND 100n
B7 8 11
6 15 12 RB2 RB5
6 Logic 6 Vrf(-) lsb-B8
19
9 10
7 16 1 RB3 RB4 GND

-Vs
7 Logic 5 COMPen THRcnt
20 R7
8
8 Logic 4 1K8
21 DAC-0800 PIC16F84
3

9 Logic 3
9 C3
22 GND
B 10 103 B
10 Logic 2 PIC Types
23
GND
11
11 Logic 1 Use any 18pin device which
24
can operate at 20MHz and
12
12 Logic 0 executes 16F84 instructions
25
as a minimum requirement.
13
C4
13 -10V
DB25-F
104

GND

A Metachip Pty Ltd A

Title WavePOD Card Sheet 1 of 1


WavePOD C bitscope
designs A3 Document Number WavePOD-01 Rev 1

Date: 13-Mar-2002 E:\WINDOWS\NJJ\WAVEPOD\WAVEPOD.SCH

1 2 3 4 5 6 7 8 9

You might also like