LC370WUN

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ●) Final Specification

Title 37.0” WUXGA TFT LCD

BUYER General SUPPLIER LG.Philips LCD Co., Ltd.

MODEL *MODEL LC370WUN

SUFFIX SAB1(RoHS Verified)
*When you obtain standard approval,
please use the above model name without suffix

SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE

/ O.H. Lee / Manager

REVIEWED BY

/ J.H. Lee / Engineer

PREPARED BY

/ H.S. Choi / Engineer

Please return 1 copy for your confirmation with TV Product Development Dept.
your signature and comments. LG. Philips LCD Co., Ltd

Ver. 1.0 1 /34

 LC370WUN
Product Specification

CONTENTS
Number ITEM Page
COVER 1

CONTENTS 2
RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS 6

3-1 ELECTRICAL CHARACTERISTICS 6

3-2 INTERFACE CONNECTIONS 8

3-3 SIGNAL TIMING SPECIFICATIONS 10

3-4 SIGNAL TIMING WAVEFORMS 11

3-5 COLOR DATA REFERENCE 12

3-6 POWER SEQUENCE 13

4 OPTICAL SPECIFICATIONS 15

5 MECHANICAL CHARACTERISTICS 19

6 RELIABILITY 22

7 INTERNATIONAL STANDARDS 23

7-1 SAFETY 23

7-2 EMC 23

8 PACKING 24

8-1 DESIGNATION OF LOT MARK 24

8-2 PACKING FORM 24

9 PRECAUTIONS 25
9-1 MOUNTING PRECAUTIONS 25
9-2 OPERATING PRECAUTIONS 25
9-3 ELECTROSTATIC DISCHARGE CONTROL 26
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 26
9-5 STORAGE 26
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM 26

Ver. 1.0 2 /34

 LC370WUN
Product Specification

RECORD OF REVISIONS

Revision No. Revision Date Page Description

1.0 Feb, 26, 2007 - Final specification.

Ver. 1.0 3 /34

 LC370WUN
Product Specification

1. General Description
The LC370WUN is a Color Active Matrix Liquid Crystal Display with an integral External Electrode
Fluorescent Lamp(EEFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active
element. It is a transmissive display type which is operating in the normally black mode. It has a 37 inch
diagonally measured active display area with WUXGA resolution (1080 vertical by 1920 horizontal pixel
array). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 10-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 1.06B (true) colors.
It has been designed to apply the 10-bit 2-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

Mini-LVDS(RGB)
EEPROM
Source Driver Circuit
SCL SDA S1 S1920
+12.0V
G1
Gate Driver Circuit

LVDS
CN1
2Port (51pin) Timing Controller

AI En
TFT - LCD Panel
(1920 × RGB × 1080 pixels)
Ext Vbr
Vbr out
Power Circuit G1080
Block

+24.0V, GND, VBR-A, VBR-B

Status Inverter(Master) 14PinX1CN(High) Back light Assembly

General Features
Active Screen Size 37 inches(940.091mm) diagonal
Outline Dimension 877(H) x 516.8 (V) x 55.5 mm(D) (Typ.)
Pixel Pitch 0.42675 mm x 0.42675 mm
Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Color Depth 10-bit(D), 1.06 B colors
Luminance, White 500 cd/m2 (Center 1point ,Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Typ.), U/D 178 (Typ.))
Power Consumption Total 132.14W (Typ.) (Logic=7.14 W, Inverter=125W [VBR-A=1.65V] )
Weight 9.0Kg (Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 13%)

Ver. 1.0 4 /34

 LC370WUN
Product Specification

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.

Table 1. ABSOLUTE MAXIMUM RATINGS

Value
Parameter Symbol Unit Remark
Min Max

Power Input LCM VLCD +8.0 +14.0 VDC at 25 ± 2 °C

Voltage Backlight inverter VBL -0.3 +27.0 VDC

ON/OFF Control Voltage VON/OFF -0.3 +5. 25 VDC

Brightness Control Voltage VBR 0 +5.0 VDC
Operating Temperature TOP 0 +50 °C
Storage Temperature TST -20 +60 °C
Note 1,2
Operating Ambient Humidity HOP 10 90 %RH

Storage Humidity HST 10 90 %RH

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 °C Max. and no condensation of water.
2. Gravity mura can be guaranteed under 40 condition. ℃

90%

60
60%

50 Storage
Humidity [(%)RH]

Wet Bulb
Temperature [°C]
40
40%
Operation
30

20
10
0
10%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [°C]

Ver. 1.0 5 /34

 LC370WUN
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the EEFL
backlight and inverter circuit.

Table 2. ELECTRICAL CHARACTERISTICS

Value
Parameter Symbol Unit Note
Min Typ Max
Circuit :

Power Input Voltage VLCD 11.4 12.0 12.6 VDC

- 595 775 mA 1
Power Input Current ILCD
- 795 1035 mA 2

Power Consumption PLCD - 7.14 9.3 Watt 1

Rush current IRUSH - - 4.0 A 3

Note : 1. The specified current and power consumption are under the VLCD=12.0V, 25 ± 2°C, fV=60Hz
condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at full white pattern.
3. The duration of rush current is about 2ms and rising time of power input is 1ms (min.).

White : 255Gray
Black : 0Gray White : 255 Gray

Mosaic Pattern(8 x 6)
Full White pattern

Ver. 1.0 6 /34

 LC370WUN
Product Specification

Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Values
Parameter Symbol Unit Notes
Min Typ Max
Inverter :
Power Supply Input Voltage VBL 22.8 24.0 25.2 Vdc 1

Power Supply Input Voltage Ripple - - 0.5 Vp-p 1

- 5.2 5.5 A VBR-A = 1.65V … 1
After Aging IBL_A
Power Supply - 5.7 6 A VBR-A = 3.3V … 1
Input Current - 6 6.3 A VBR-A = 1.65V … 2
Before Aging IBL_B
- 6.5 6.8 A VBR-A = 3.3V … 2
VBL = 22.8V
Power Supply Input Current (In-Rush) Irush - - 8 A VBR-B = 3.3V
VBR-A = 1.65V

Power Consumption PBL - 125 132 W VBR-A = 1.65V … 1

Brightness Adjust VBR-A 0.0 1.65 3.3 Vdc

Input Voltage for On V on 2.5 - 5.0 Vdc

Control System On/Off
Signals Off V off -0.3 0.0 0.8 Vdc

Brightness Adjust VBR-B 0 - 3.3 V

Lamp:

Discharge Stabilization Time Ts 3 min 3

Life Time 50,000 Hrs 4

Notes :
1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 120
minutes at 25± 2°C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (VBR-A : 1.65V & VBR-B :3.3V), it is total power consumption.
The ripple voltage of the power supply input voltage is under 0.5 Vp-p. LPL recommend Input Voltage is
24.0V ± 5%.
2. Electrical characteristics are determined within 30 minutes at 25± 2°C.
The specified currents are under the typical supply Input voltage 24V.
3. The brightness of the lamp after lighted for 5minutes is defined as 100%.
TS is the time required for the brightness of the center of the lamp to be not less than 95% at typical current.
The screen of LCD module may be partially dark by the time the brightness of lamp is stable after turn on.
4. Specified Values are for a single lamp which is aligned horizontally.
The life time is determined as the time which luminance of the lamp is 50% compared to that of initial value
at the typical lamp current (VBR-A : 1.65V & VBR-B :3.3V), on condition of continuous operating at 25± 2°C
5. The duration of rush current is about 20 ms.

Ver. 1.0 7 /34

 LC370WUN
Product Specification

3-2. Interface Connections

This LCD module employs two kinds of interface connection, a 51-pin connector is used for the module
electronics and Master 14-pin connector is used for the integral backlight system.

3-2-1. LCD Module

- LCD Connector(CN1): FI-R51S-HF(manufactured by JAE)
- Mating Connector : FI-R51HL(JAE) or compatible

Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION

No Symbol Description No Symbol Description

1 GND Ground 27 BIT SEL ‘L’ =8bit, ‘H’ =10bit(D)

2 NC No Connection 28 RE0N SECOND CHANNEL 0-
3 NC No Connection 29 RE0P SECOND CHANNEL 0+
4 NC No Connection 30 RE1N SECOND CHANNEL 1-
5 NC No Connection 31 RE1P SECOND CHANNEL 1+
6 NC No Connection 32 RE2N SECOND CHANNEL 2-
7 LVDS Select ‘H’ = JEIDA, ‘L’ = VESA 33 RE2P SECOND CHANNEL 2+
8 VBR_Ext EXT_VBR 34 GND Ground
9 VBR_OUT VER_OUT 35 RECLKN SECOND CLOCK CHANNEL C-
10 DCR_EN “L”=OFF,”H”=ON 36 RECLKP SECOND CLOCK CHANNEL C+
11 GND Ground 37 GND Ground
12 RO0N FIRST CHANNEL 0- 38 RE3N SECOND CHANNEL 3-
13 RO0P FIRST CHANNEL 0+ 39 RE3P SECOND CHANNEL 3+
14 RO1N FIRST CHANNEL 1- 40 RE4N SECOND CHANNEL 4-
15 RO1P FIRST CHANNEL 1+ 41 RE4P SECOND CHANNEL 4+
16 RO2N FIRST CHANNEL 2- 42 Reserved No connection or GND
17 RO2N FIRST CHANNEL 2+ 43 Reserved No connection or GND
18 GND Ground 44 GND Ground
19 ROCLKN FIRST CLOCK CHANNEL C- 45 GND Ground
20 ROCLKP FIRST CLOCK CHANNEL C+ 46 GND Ground
21 GND Ground 47 NC No connection
22 RO3N FIRST CHANNEL 3- 48 VLCD Power Supply +12.0V
23 RO3P FIRST CHANNEL 3+ 49 VLCD Power Supply +12.0V
24 RO4N FIRST CHANNEL 4- 50 VLCD Power Supply +12.0V
25 RO4P FIRST CHANNEL 4+ 51 VLCD Power Supply +12.0V
26 Reserved No connection or GND - - -

Note :
1. The pin no 44 is LCD Test option. “AGP” (Auto Generation LCM operates Pattern) or “NSB” (No Signal
Black) is case that LVDS signals are out of frequency or abnormal condition in spite of 12 volt power
supply. LPL recommends “NSB”. ( AGP : “VCC” or “OPEN” / NSB : “GND” )
2. All GND(ground) pins should be connected together to the LCD module’s metal frame.
3. All VLCD (power input) pins should be connected together.
4. All Input levels of LVDS signals are based on the IEA 664 Standard.
5. Specific pins(pin No. #1~#10) are used for internal data process of the LCD module.
If not used, these pins are no connection.
6. If DCR function should be enable(‘H’), 10th pin must be connected to serial resistor which value is under
1k ohm.

Ver. 1.0 8 /34

 LC370WUN
Product Specification

3-2-2. Backlight Inverter

Inverter Connector : S14B-PH-SMC

(manufactured by JST) or Equivalent
- Mating Connector : PHR-14 or Equivalent

Table 5. INVERTER CONNECTOR PIN CONFIGULATION

Pin No Symbol Description Note

1 VBL Power Supply +24.0V

2 VBL Power Supply +24.0V

3 VBL Power Supply +24.0V

4 VBL Power Supply +24.0V

5 VBL Power Supply +24.0V

6 GND Backlight Ground

7 GND Backlight Ground
8 GND Backlight Ground 1
9 GND Backlight Ground
10 GND Backlight Ground
Analog dimming voltage
11 VBR-A
DC 0.0V ~ 3.3V (Typ : 1.65V)
2, 3

12 VON/OFF 0.0V ~ 5.0V

Burst dimming voltage
13 VBR-B 3
DC 0.0V ~ 3.3V
Normal : Upper 3.0V
14 Status 4
Abnormal : Under 0.7V

Note : 1. GND should be connected to the LCD module’s metal frame.

2. If Pin #11 is open, VBR-A = 1.65V. When apply over 1.65V( ~ 3.3V)continuously,
its luminance is increasing however lamp’s life time is decreasing.
It could be usable for boost up luminance when using DCR (=Dynamic contrast ratio) function only.
3. Minimum Brightness : VBR-B =0V Maximum Brightness : VBR-B = 3.3V
4. Even though Pin #14 is open, there is no effect on inverter operating, The output terminal of inverter.
Ω Ω
5. Each impedance of pin #11,12 and 13 is 150[K ] , 200[K ] and 150[K ]. Ω
◆ Rear view of LCM
PCB

14
…
…

Ver. 1.0 9 /34

 LC370WUN
Product Specification

3-3. Signal Timing Specifications

Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal timing
should be satisfied with the following specification for normal operation.

Table 6. TIMING TABLE for NTSC (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note
Display Period tHV - 960 - tclk
Horizontal Blank tHB 72 140 320 tclk
Total tHP 1032 1100 1280 tclk 2200/2
Display Period tVV - 1080 - Lines
Vertical Blank tVB 10 45 86 Lines
Total tVP 1090 1125 1166 Lines

ITEM Symbol Min Typ Max Unit Note

DCLK fCLK 70.5 74.25 78 MHz 148.5/2
Frequency Horizontal fH 64.1 67.5 70.9 KHz
Vertical fV 57 60 63 Hz

Table 7 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal timing
should be satisfied with the following specification for normal operation.

Table 7. TIMING TABLE for PAL (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note

Display Period tHV - 960 - tclk
Horizontal Blank tHB 72 140 320 tclk
Total tHP 1032 1100 1280 tclk 2200/2
Display Period tVV - 1080 - Lines
Vertical Blank tVB 228 270 300 Lines
Total tVP 1308 1350 1380 Lines

ITEM Symbol Min Typ Max Unit Note

DCLK fCLK 70.5 74.25 78 MHz 148.5/2
Frequency Horizontal fH 64.1 67.5 70.9 KHz
Vertical fV 47.5 50 52.5 Hz

Note : The Input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode).
The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rate.

Ver. 1.0 10 /34

 LC370WUN
Product Specification

3-4. Signal Timing Waveforms

0.7VDD
DE, Data
0.3VDD

tCLK
DCLK 0.5 VDD

Valid data

First data Invalid data Pixel 0,0 Pixel 2,0 Invalid data

Valid data

Second data Invalid data Pixel 1,0 Pixel 3,0 Invalid data

DE(Data Enable)

* tHB = tHFP + tWH +tHBP

* Reference : Sync. Relation
* tVB = tVFP + tWV +tVBP
tHP
HSync tWH

tHBP tHV tHFP

DE(Data Enable)

tVP
tWV

VSync
tVBP tVV tVFP

DE(Data Enable)

Ver. 1.0 11 /34

 LC370WUN
Product Specification

3-5. Color Data Reference

The brightness of each primary color(red,green,blue) is based on the 10-bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 10 provides a reference for color versus data input.

Table 8. COLOR DATA REFERENCE

Input Color Data

RED GREEN BLUE

Color
MSB LSB MSB LSB MSB LSB

R9 R8 R7 R6 R5 R4 R3 R2 R1 R0 G9 G8 G7 G6 G5 G4 G3 G2 G1 G0 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red (1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green
0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0
(1023)

Basic Blue (1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Color Cyan 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (001) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED ... ... ... ...

RED (1022) 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0

GREEN ... ... ... ...

GREEN
0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0
(1022)
GREEN
0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0
(1023)
BLUE (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE ... ... ... ...

BLUE (1022) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0

BLUE (1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Ver. 1.0 12 /34

 LC370WUN
Product Specification

3-6. Power Sequence

3-6-1. LCD Driving circuit

90% 90%
Power Supply For LCD
VLCD 10% 10%
0V

T1 T6
Valid Data
T2 T5
Invalid Invalid
Interface Signal (Tx) Data Data
0V

T3 T4

Option Signal T7 T8
(LVDS_select, DCR_Enable, BIT_select)

Lamp ON
Power for Lamp

Table 9. POWER SEQUENCE

Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - 20 ms
T2 0 - - ms 4
T3 200 - - ms 3
T4 200 - - ms 3
T5 0 - - ms
T6 2.0 - - s 5
T7 0 - T2 ms 4
T8 0 - - ms 4

Note : 1. Please avoid floating state of interface signal at invalid period.

2. When the interface signal is invalid, be sure to pull down the power supply VLCD to 0V.
3. The T3/T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. If the on time of signals(Interface signal and Option signals) precedes the on time of Power(VLCD),
check the LCD logic Power(Vcc) is under 0.8V, otherwise it will be happened abnormal display.
5. T6 should be measured after the Module has been fully discharged between power off and on
period.

Ver. 1.0 13 /34

 LC370WUN
Product Specification

3-6-2. Sequence for Inverter

Power Supply For Inverter

24V (typ.)
90%
VBL
10% 0.7V
0V

T1 T2 1000ms (Min) T5 T3 T2 1000ms (Min)

VON/OFF Lamp ON

T4 T4

VBR-A &
VBR-B
T7

3-6-3. Deep condition for Inverter

T6
VBL : 24V

VBL(Typ.) x 0.8

0V

Table 10. Power Sequence for Inverter

Values
Parameter Units Remarks
Min Typ Max
T1 20 - - ms 1
T2 500 - - ms
T3 200 - - ms
T4 0 - ms 2
T5 10 - - ms
T6 - - 10 ms VBL(Typ) x 0.8
T7 1000 - - ms 3
Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.
2. T4(max) is less than T2.
3. In T7 section, VBR-A should be more than 1.65V and Vbr-B should be 3.3V

Ver. 1.0 14 /34

 LC370WUN
Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25± 2°C.
The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of Φ and θ
equal to 0 °.
FIG. 1 shows additional information concerning the measurement equipment and method.

LCD Module Pritchard 880 or

Optical Stage(x,y)
equivalent

50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method

Table 11. OPTICAL CHARACTERISTICS

Ta= 25± 2°C, VLCD=12.0V, fV=60Hz, Dclk=148.5MHz VBR_A=1.65V, VBR_B=3.3V

Value
Parameter Symbol Unit Note
Min Typ Max
Contrast Ratio CR 900 1300 - 1
Surface Luminance, white LWH 400 500 - cd/m2 2
Luminance Variation δ WHITE 5P - - 1.3 3
Gray-to-Gray G to G - 5 8
Response Time ms 4
MPRT - -
Rx 0.638
RED
Ry 0.334
Gx 0.291
GREEN
Color Coordinates Gy 0.607
[CIE1931] BLUE Bx Typ 0.145 Typ
By -0.03 0.062 +0.03
WHITE Wx 0.279
Wy 0.292
Viewing Angle (CR>10)
x axis, right(φ=0°) θr 89 - -
x axis, left (φ=180°) θl 89 - -
degree 5
y axis, up (φ=90°) θu 89 - -
y axis, down (φ=270°) θd 89 - -
Gray Scale - - - 6

Ver. 1.0 15 /34

 LC370WUN
Product Specification
Note :1. Contrast Ratio(CR) is defined mathematically as :
CR(Contrast Ratio) = Maximum CRn (n=1, 2, 3, 4, 5)
Surface Luminance at position n with all white pixels
CRn =
Surface Luminance at position n with all black pixels
n = the Position number(1, 2, 3, 4, 5). For more information, see FIG 2.

2. Surface luminance are determined after the unit has been ‘ON’ and 30min after lighting the
backlight in a dark environment at 25± 2°C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.

3. The variation in surface luminance , δ WHITE is defined as :

δ WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5)
Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations .
For more information, see the FIG. 2.
4. Response time is the time required for the display to transition from G(N) to G(M) (Rise Time, TrR)

※
and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M)
G to G spec is average of measured time(N,M= 0(Black)~255(White), 32Gray step

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 5.
6. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 12.

Table 12. GRAY SCALE SPECIFICATION

Gray Level Luminance [%] (Typ.)
L0 0.08
L63 0.20
L127 1.08
L191 2.07
L255 4.51
L319 7.75
L383 12.05
L447 17.06
L511 22.36
L575 28.21
L639 35.56
L703 43.96
L767 53.00
L831 63.37
L895 74.66
L959 88.17
L1023 100

Ver. 1.0 16 /34

 LC370WUN
Product Specification

Measuring point for surface luminance & measuring point for luminance variation.

H
A

② ③

①
V
B

A : H / 4 mm
④ ⑤ B : V / 4 mm
@ H,V : Active Area

FIG. 2 5 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Gray(M)”.

T rR T rD
100
90

Optical
Response

10
Gray(N) Gray(M) Gray(N)
0
N,M = Black~White, N<M

FIG. 3 Response Time

Ver. 1.0 17 /34

 LC370WUN
Product Specification

Dimension of viewing angle range

Normal
E Y
φ = 90°, Up

φ = 180°, Left
θ

φ = 0°, Right

φ = 270°, Down

FIG. 4 Viewing Angle

Ver. 1.0 18 /34

 LC370WUN
Product Specification

5. Mechanical Characteristics

Table 13 provides general mechanical characteristics.

Table 13. MECHANICAL CHARACTERISTICS

Item Value

Horizontal 877.0 mm

Outline Dimension Vertical 516.8 mm

Depth 55.5 mm

Horizontal 828.6 mm
Bezel Area
Vertical 469.8 mm

Horizontal 819.36 mm
Active Display Area
Vertical 460.89 mm

Weight 9000(Typ.)/9500(Max)

Note : Please refer to a mechanic drawing in terms of tolerance at the next page.

Ver. 1.0 19 /34

 LC370WUN
Product Specification

<FRONT VIEW>

Ver. 1.0 20 /34

 LC370WUN
Product Specification
<REAR VIEW>

Ver. 1.0 21 /34

 LC370WUN
Product Specification

6. Reliability

Table 14. ENVIRONMENT TEST CONDITION

No. Test Item Condition

1 High temperature storage test Ta= 60°C 240h

2 Low temperature storage test Ta= -20°C 240h

3 High temperature operation test Ta= 50°C 50%RH 240h

4 Low temperature operation test Ta= 0°C 240h

Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z, 30 min
One time each direction

Shock level : 50Grms

Shock test Waveform : half sine wave, 11ms
6
(non-operating) Direction : ±X, ±Y, ±Z
One time each direction

7 Humidity condition Operation Ta= 40 °C ,90%RH

Altitude operating 0 - 15,000 ft

8
storage / shipment 0 - 40,000 ft

Note : Before and after Reliability test, LCM should be operated with normal function.

Ver. 1.0 22 /34

 LC370WUN
Product Specification

7. International Standards

7-1. Safety
a) UL 60065, 7th Edition, dated June 30, 2003, Underwriters Laboratories, Inc.,
Standard for Audio, Video and Similar Electronic Apparatus.
b) CAN/CSA C22.2, No. 60065:03, Canadian Standards Association,
Standard for Audio, Video and Similar Electronic Apparatus.
c) IEC60065:2001, 7th Edition CB-scheme and EN 60065:2002,
Safety requirements for Audio, Video and Similar Electronic Apparatus..

7-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992
b) CISPR13 "Limits and Methods of Measurement of Radio interference characteristics of Sound
and Television broadcast receivers and associated equipment"
CISPR22 "Limits and Methods of Measurement of Radio interference characteristics of Information
Technology Equipment" International Special Committee on Radio Interference.
c) EN55013 "Limits and Methods of Measurement of Radio interference characteristics of Sound and
Television broadcast receivers and associated equipment"
EN55022 "Limits and Methods of Measurement of Radio interference characteristics of Information
Technology Equipment" European Committee for Electro Technical Standardization.(CENELEC),
1988(Including A1:2000)

Ver. 1.0 23 /34

 LC370WUN
Product Specification

8. Packing

8-1. Designation of Lot Mark

a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

Mark 1 2 3 4 5 6 7 8 9 0

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 4 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one box : 4 pcs

b) Box Size : 968mm X 366mm X 595mm

Ver. 1.0 24 /34

 LC370WUN
Product Specification

9. Precautions

Please pay attention to the followings when you use this TFT LCD module.

9-1. Mounting Precautions

(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=± 200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer
(4) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it can causes conductive particles and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) It is recommended to avoid the signal cable and conductive material over the inverter transformer
for it can cause the abnormal display and temperature rising.

Ver. 1.0 25 /34

 LC370WUN
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.

Ver. 1.0 26 /34

 LC370WUN
Product Specification
# APPENDIX-I-1
■ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7=“L”)

Host System THC63LVD103

30 Bit or Compatible Timing
RED0 33 Controller
RED1 34 FI-RE51S-HF
RED2 35
RED3 36
31
37 TA- 12 RO0N
100Ω
RED4
RED5 38 30
TA+ 13 RO0P
RED6 59
RED7 61 29
TB- 14 RO1N
RED8 4 28 100Ω
RED9 5 TB+ 15 RO1P
GREEN0 40
25
GREEN1 41 TC- 16 RO2N
GREEN2 42 TC+
24
17 100Ω RO2P
GREEN3 44
GREEN4 45 23
TCLK- 19 ROCLKN
100Ω
GREEN5 46 22
GREEN6 62 TCLK+ 20 ROCLKP
GREEN7 63
21
GREEN8 6 TD- 22 RO3N
GREEN9 8 TD+
20
23 100Ω RO3P
BLUE0 48
BLUE1 49 19
TE- 24 RO4N
100Ω
BLUE2 50 18
BLUE3 52 TE+ 25 RO4P
BLUE4 53
BLUE5 54 7 VESA / JEIDA
BLUE6 64
BLUE7 1
BLUE8 9
BLUE9 11
Hsync 55
LCM Module
GND

Vsync 57
Data Enable 58
CLOCK 12

Note:
Ω
1. The LCD module uses a 100 Ohm( ) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘9’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver. 1.0 27 /34

 LC370WUN
Product Specification
# APPENDIX-I-2
■ Required signal assignment for Flat Link (Thine : THC63LVD823) Transmitter(Pin7=“H”)

Host System THC63LVD103

30 Bit or Compatible Timing
RED0 4 Controller
RED1 5 FI-RE51S-HF
RED2 59
RED3 61
31
TA- 12 RO0N
100Ω
RED4 33
RED5 30
34 TA+ 13 RO0P
RED6 35
RED7 36 29
TB- 14 RO1N
RED8 37 28 100Ω
RED9 TB+ 15 RO1P
38
GREEN0 6
25
GREEN1 8 TC- 16 RO2N
GREEN2 62 TC+
24
17 100Ω RO2P
GREEN3 63
GREEN4 40 23
TCLK- 19 ROCLKN
GREEN5 41
TCLK+
22
20 100Ω ROCLKP
GREEN6 42
GREEN7 44
21
GREEN8 45 TD- 22 RO3N
GREEN9 46 TD+
20
23 100Ω RO3P
BLUE0 9
BLUE1 11 19
TE- 24 RO4N
100Ω
BLUE2 64 18
BLUE3 1 TE+ 25 RO4P
BLUE4 48
BLUE5 49 7 VESA / JEIDA
BLUE6 50
BLUE7 52
BLUE8 53
BLUE9 54
Hsync 55
LCM Module
VCC

Vsync 57
Data Enable 58
CLOCK 12

Note:
Ω
1. The LCD module uses a 100 Ohm( ) resistor between positive and negative lines
of each receiver input.
2. Refer to LVDS transmitter data sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘9’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver. 1.0 28 /34

 LC370WUN
Product Specification
Ⅱ-1
# APPENDIX-Ⅱ

■ LC370WUN-SAB1 Packing Ass’y

NO. DESCRIPTION MATERIAL

1 LCD MODULE
2 BAG AL
3 TAPE MASKING 20MM X 50M
4 PACKING, BOTTOM EPS
5 PACKING, TOP R_L EPS
6 BOX PAPER_DW3
7 TAPE OPP 70MMX300M
8 LABEL YUPO PAPER 100X100

Ver. 1.0 29 /34

 LC370WUN

# APPENDIX 2 Product Specification

Ⅱ-2
# APPENDIX-Ⅱ

■ LC370WUN-SAB1 Pallet Ass’y

NO. DESCRIPTION MATERIAL

1 PACKING ASS’Y

2 PALLET Plywood_1140X990X130
3 ANGLE, COVER DW3
4 LABEL YUPO PAPER
5 TAPE OPP
6 BAND PP
7 BAND, CLIP CLIP 18MM

Ver. 1.0 30 /34

 LC370WUN

# APPENDIX 2 Product Specification

Ⅱ-3
# APPENDIX-Ⅱ

■ LCM Label

LC370WUN
Model
(SA)(B1)
RoHS Verified

Serial No.

UL, TUV Mark

LPL Logo MADE IN KOREA Origin
US PATENT No.

■ Serial No. (See CAS 24page for more information)

1 2 3 4 5 6 7 8 9 10 11 12 13

Inch Year Month

Serial No.

M Ass’y Factory code

Ver. 1.0 31 /34

 LC370WUN

# APPENDIX 3 Product Specification

Ⅱ-4
# APPENDIX-Ⅱ
■ Box Label ■ Pallet Label

LC370WUN LC370WUN
SAB1
SAB1
4 PCS L O T/MM-DD

MADE IN KOREA RoHS Verified

12 PCS LOT/MM-DD

MADE IN KOREA RoHS Verified

* * * * * * * * * * * * * * * *

* * * * * * * * * * * * * * * *

Ver. 1.0 32 /34

 LC370WUN
Product Specification
# APPENDIX-ⅢⅢ-1
■ LCM DCR Only
LCM Control Board
Pin : VBR_EXT
NTSC / PAL Pin : VBR_OUT
Sync_PWM
1 51
FFC Cable

System
LCM
Board
12V
# 10
Inverter
DCR_Enable Pin
3.3V

VBR- B
3.3V VBR-
VBR- B
14 13

11
VBR- A
NC / 1.65V

Luminance [%] DCR On

Gray Level
■ DCR_Enable Option Pin Description L0
VBR-A = 1.65V
0.01
DCR_Enable On(3.3V) Off (0V) L15
L31
VBR_OUT From T-Con From System L47
(VBR-B) (ASIC) (VBR_EXT Pin) L63
Signal Source L79
L95
VBR-B 0V ~ 3.3V 3.3V L111
L127
VBR-A 1.65V or NC 1.65V or NC L143
L159

DCR Level 10,000 : 1 1300 : 1 L175

L191
L207
L223
L239
L255 100

Ver. 1.0 33 /34

 LC370WUN
Product Specification
# APPENDIX-Ⅲ Ⅲ-2
■ System DCR (Dynamic Contrast Ratio)- Max 13,000:1

NTSC / PAL LCM Control Board

Sync_PWM
1 51
FFC Cable

System
LCM
Board 51 1
12V
Inverter
# 10 : DCR Enable Pin

VBR-
BR- B

0V ~ 3.3V
14 13

11
VBR-
BR- A
0V ~ 3.3V

VBR-B 0V ~ 3.3V 3.3V VBR-A,B Voltage Function

VBR-B : 3.3V Maximum Brightness (100%)

VBR-A 0V ~ 1.65V 1.65V (DCR Condition)
VBR-A : 1.65V
DCR Level 13,000:1 1300 : 1 0V Minimum Brightness (10%)

Note : 1. To make DCR Max (Bare CR)X10, VBR-A and VBR-B must be given by system.
2. DCR Max 10,000:1 is defined mathematically as :
DCR = Maximum DCRn (n=1, 2, 3, 4, 5)
Surface Luminance at position n with all white pixels (VBR-B=3.3V, VBR-A=1.65V)
DCRn =
Surface Luminance at position n with all black pixels (VBR-B=0V, VBR-A=0V)

n = the Position number(1, 2, 3, 4, 5). For more information, see FIG 2.

3. Measurement Sequence (aging time 10 min each pattern) :
① Turn On LCM
② Measure Black Luminance (VBR-B=0V, VBR-A=0V)
③ Measure White Luminance (VBR-B=3.3V, VBR-A=1.65V)
4. In case the lowest minimum brightness is continued,
it can affect the lamp reliability and appear the partial darkness.

Ver. 1.0 34 /34