Scribd
Upload
45 views3 pages

Configuracion de Tabla DSCP

This document provides instructions for configuring DSCP tables on a CPE device. The steps are: 1. Telnet into the CPE and navigate to the Service Parameters ETHCS menu. 2. Configure the operation mode to Ethernet CS and add two service rules - one mapping DSCP 0-39 to VLAN 20 and another mapping DSCP 40-63 to VLAN 10. 3. Verify the DSCP to VLAN mappings were correctly configured by viewing the DSCP to VLAN table.

Uploaded by

MochoInr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
45 views3 pages

Configuracion de Tabla DSCP

This document provides instructions for configuring DSCP tables on a CPE device. The steps are: 1. Telnet into the CPE and navigate to the Service Parameters ETHCS menu. 2. Configure the operation mode to Ethernet CS and add two service rules - one mapping DSCP 0-39 to VLAN 20 and another mapping DSCP 40-63 to VLAN 10. 3. Verify the DSCP to VLAN mappings were correctly configured by viewing the DSCP to VLAN table.

Uploaded by

MochoInr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

CONFIGURACION DE TABLA DSCP

Ingresar al CPE por telnet

C:\> telnet 192.168.254.251


You are connected to configuration tool
Enter the password: installer

======================================================
SU / [00:10:E7:22:D0:F6]
SW version: 2.5.1.1060
======================================================

Path: /

1. Show All Parameters and Status


2. Unit Control Verificar que se tenga la opción 9,
3. Registration Parameters en caso que no se tenga esta
4. BS Parameters
5. Radio Parameters opción entrar en la 8.
6. Multirate and ATPC Parameters
7. Performance Monitoring Luego en 2. Operation Mode y
9. Service Parameters ETHCS setear en Ethernet CS
10. Management Parameters
11. Exit
Enter your choice > 9 Reiniciar el CPE

======================================================
SU / [00:10:E7:22:D0:F6]
SW version: 2.5.1.1060
======================================================

Path: /Service Parameters ETHCS/

1. Show
2. Operation Mode
3. Add Service Rule
4. Delete Service Rule
5. Delete All Service Rules
6. Bridge
Enter your choice > 2

Configured CS Type: Ethernet CS Mode


Actual CS Type: Ethernet CS Mode

Type in CS Type (IP CS 0 , Ethernet CS 1) [0..1] > 1


Configurar la tabla

Dentro del menú Service Parameters ETHCS configuramos:

======================================================
SU / [00:10:E7:22:D0:F6]
SW version: 2.5.1.1060
======================================================

Path: /Service Parameters ETHCS/

1. Show
2. Operation Mode
3. Add Service Rule
4. Delete Service Rule
5. Delete All Service Rules
6. Bridge
Enter your choice > 3
Type DSCP Start Value (0-63, 64: N/A) [0..64] > 0
Type DSCP Stop Value (0-63, 64: N/A) [0..64] > 39
Type VLAN ID Value (0-4095, 4096: Transparent) [0..4096] > 20
Type VLAN Priority Value (0-7, 8: Transparent) [0..8] > 0

======================================================
SU / [00:10:E7:22:D0:F6]
SW version: 2.5.1.1060
======================================================

Path: /Service Parameters ETHCS/

1. Show
2. Operation Mode
3. Add Service Rule
4. Delete Service Rule
5. Delete All Service Rules
6. Bridge
Enter your choice > 3
Type DSCP Start Value (0-63, 64: N/A) [0..64] > 40
Type DSCP Stop Value (0-63, 64: N/A) [0..64] > 63
Type VLAN ID Value (0-4095, 4096: Transparent) [0..4096] > 10
Type VLAN Priority Value (0-7, 8: Transparent) [0..8] > 5
Verificamos

======================================================
SU / [00:10:E7:22:D0:F6]
SW version: 2.5.1.1060
======================================================

Path: /Service Parameters ETHCS/

1. Show
2. Operation Mode
3. Add Service Rule
4. Delete Service Rule
5. Delete All Service Rules
6. Bridge
Enter your choice > 1

DSCP to VLAN table


RULE DSCP START DSCP OUT VLAN ID OUT VLAN PRIORITY
ID STOP
1 0 39 20 0
2 40 63 10 5

Type DSCP Start Value (0-63, 64: N/A) [0..64] > 0


Type DSCP Stop Value (0-63, 64: N/A) [0..64] > 39
Type VLAN ID Value (0-4095, 4096: Transparent) [0..4096] > 20
Type VLAN Priority Value (0-7, 8: Transparent) [0..8] > 0

Type DSCP Start Value (0-63, 64: N/A) [0..64] > 40


Type DSCP Stop Value (0-63, 64: N/A) [0..64] > 63
Type VLAN ID Value (0-4095, 4096: Transparent) [0..4096] > 10
Type VLAN Priority Value (0-7, 8: Transparent) [0..8] > 5

You might also like