Scribd
Upload
86 views4 pages

Data Sheet 6AG1332-1SH71-4AA0: Input

Uploaded by

Abdallah Abdelrehim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
86 views4 pages

Data Sheet 6AG1332-1SH71-4AA0: Input

Uploaded by

Abdallah Abdelrehim
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Data sheet 6AG1332-1SH71-4AA0

SIPLUS POWER MODUL PM1207


SIPLUS S7-1200 PM 1207 for medial exposure with conformal
coating based on 6EP1332-1SH71 . Stabilized power supplies Input:
120/230 V AC Output: 24 V DC/2.5 A

Input
Input 1-phase AC
● Note Automatic range selection
supply voltage
● 1 at AC rated value 120 V
● 2 at AC rated value 230 V
input voltage
● 1 at AC 85 ... 132 V
● 2 at AC 176 ... 264 V
Wide-range input No
Overvoltage resistance 2.3 × Vin rated, 1.3 ms
Mains buffering at Vin = 93/187 V
Mains buffering at Iout rated, min. 20 ms; at Vin = 93/187 V
Rated line frequency 1 50 Hz
Rated line frequency 2 60 Hz
Rated line range 47 ... 63 Hz
input current

6AG1332-1SH71-4AA0 Subject to change without notice


Page 1/4 11/27/2020 © Copyright Siemens
● at rated input voltage 120 V 1.2 A
● at rated input voltage 230 V 0.67 A
Switch-on current limiting (+25 °C), max. 13 A
duration of inrush current limiting at 25 °C
● maximum 3 ms
I²t, max. 0.5 A²·s
Built-in incoming fuse T 3,15 A/250 V (not accessible)
Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: 16 A characteristic B or
10 A characteristic C

Output
Output Controlled, isolated DC voltage
Rated voltage Vout DC 24 V
Total tolerance, static ± 3 %
Static mains compensation, approx. 0.1 %
Static load balancing, approx. 0.2 %
Residual ripple peak-peak, max. 150 mV
Spikes peak-peak, max. (bandwidth: 20 MHz) 240 mV
product function output voltage adjustable No
Output voltage setting -
Status display Green LED for 24 V OK
On/off behavior No overshoot of Vout (soft start)
Startup delay, max. 6 s; 2 s at 230 V, 6 s at 120 V
Voltage rise, typ. 10 ms
Rated current value Iout rated 2.5 A
Current range 0 ... 2.5 A
supplied active power typical 60 W
short-term overload current
● on short-circuiting during the start-up typical 6 A
● at short-circuit during operation typical 6 A
duration of overloading capability for excess current
● on short-circuiting during the start-up 100 ms
● at short-circuit during operation 100 ms
Parallel switching for enhanced performance Yes
Numbers of parallel switchable units for enhanced 2
performance

Efficiency
Efficiency at Vout rated, Iout rated, approx. 83 %
Power loss at Vout rated, Iout rated, approx. 12 W

Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), 0.3 %
max.

6AG1332-1SH71-4AA0 Subject to change without notice


Page 2/4 11/27/2020 © Copyright Siemens
Dynamic load smoothing (Iout: 50/100/50 %), Uout ± 3 %
typ.
Load step setting time 50 to 100%, typ. 5 ms
Load step setting time 100 to 50%, typ. 5 ms
setting time maximum 5 ms

Protection and monitoring


Output overvoltage protection < 33 V
Current limitation, typ. 2.65 A
property of the output short-circuit proof Yes
Short-circuit protection Constant current characteristic
enduring short circuit current RMS value
● typical 2.7 A
Overload/short-circuit indicator -

Safety
Primary/secondary isolation Yes
galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN
50178
Protection class Class I
leakage current
● maximum 3.5 mA
Degree of protection (EN 60529) IP20

Approvals
CE mark Yes

EMC
Emitted interference EN 55022 Class B
Supply harmonics limitation not applicable
Noise immunity EN 61000-6-2

environmental conditions
ambient temperature in horizontal mounting position 0 ... 60; with natural convection
during operation
ambient temperature during storage and transport -40 ... +85
installation altitude at height above sea level 6 000 m
maximum
ambient condition relating to ambient temperature - In case of operation at altitudes of 2000 - 6000 m above sea level:
air pressure - installation altitude Output power derating of -7.5 %/1000 m or reduction of the
ambient temperature by 5 K/1000 m
relative humidity with condensation acc. to IEC 100 %; RH incl. condensation/frost (no commissioning if
60068-2-38 maximum condensation is present), horizontal installation
chemical resistance to commercially available cooling Yes; incl. diesel and oil droplets in the air
lubricants
resistance to biologically active substances Yes; Class 3B2 mold, fungal, sponge spores (except fauna); class
conformity acc. to EN 60721-3-3 3B3 upon request

6AG1332-1SH71-4AA0 Subject to change without notice


Page 3/4 11/27/2020 © Copyright Siemens
resistance to chemically active substances Yes; Class 3C4 (RH < 75%) incl. salt spray acc. to EN 60068-2-52
conformity acc. to EN 60721-3-3 (severity level 3)
resistance to mechanically active substances Yes; Class 3S4 incl. sand, dust
conformity acc. to EN 60721-3-3
resistance to biologically active substances Yes; Class 6B2 mold, fungal, sponge spores (except fauna)
conformity acc. to EN 60721-3-6
resistance to chemically active substances Yes; Class 6C3 (RH < 75%) incl. salt spray acc. to EN 60068-2-52
conformity acc. to EN 60721-3-6 (severity level 3)
resistance to mechanically active substances Yes; Class 6S3 incl. sand, dust
conformity acc. to EN 60721-3-6
coating for equipped printed circuit board acc. to EN Yes; Class 2 for high availability
61086
type of coating protection against pollution according Yes; Type 1 protection
to EN 60664-3
type of test of the coating acc. to MIL-I-46058C Yes; Discoloration of the coating during service life possible
product conformity of the coating Qualification and Yes; Conformal Coating, Class A
Performance of Electrical Insulating Compound for
Printed Board Assemblies acc. to IPC-CC-830A

Mechanics
Connection technology screw-type terminals
Connections
● Supply input L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm²
● Output L+, M: 2 screw terminals each for 0.5 ... 2.5 mm²
● Auxiliary -
width of the enclosure 70 mm
height of the enclosure 100 mm
depth of the enclosure 75 mm
required spacing
● top 20 mm
● bottom 20 mm
● left 0 mm
● right 0 mm
Weight, approx. 0.3 kg
product feature of the enclosure housing can be lined Yes
up
Installation Snaps onto DIN rail EN 60715 35x7.5/15, wall mounting
MTBF at 40 °C 1 492 537 h
other information Specifications at rated input voltage and ambient temperature +25
°C (unless otherwise specified)

6AG1332-1SH71-4AA0 Subject to change without notice


Page 4/4 11/27/2020 © Copyright Siemens

You might also like