Scribd
Upload
145 views4 pages

Maintenance Interval Schedule: When Required

The document provides a maintenance interval schedule for a 12M Motor Grader listing maintenance tasks that should be performed when required, every 10 service hours or daily, every 100 service hours or 2 weeks, initial 250 service hours, every 250 service hours, every 500 service hours or 3 months, every 1000 service hours or 1 year, every 2000 service hours or 2 years, every 2500 service hours, every 3 years, every 6000 service hours or 3 years, and every 12,000 service hours or 6 years. Maintenance tasks include checking fluid levels, replacing filters, lubricating components, inspecting and replacing wear items, and sampling fluids.

Uploaded by

Sain Meza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
145 views4 pages

Maintenance Interval Schedule: When Required

The document provides a maintenance interval schedule for a 12M Motor Grader listing maintenance tasks that should be performed when required, every 10 service hours or daily, every 100 service hours or 2 weeks, initial 250 service hours, every 250 service hours, every 500 service hours or 3 months, every 1000 service hours or 1 year, every 2000 service hours or 2 years, every 2500 service hours, every 3 years, every 6000 service hours or 3 years, and every 12,000 service hours or 6 years. Maintenance tasks include checking fluid levels, replacing filters, lubricating components, inspecting and replacing wear items, and sampling fluids.

Uploaded by

Sain Meza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Page 1 of 4

Shutdown SIS

Previous Screen

Maintenance Interval Schedule


SMCS - 1000; 7000

Ensure that all safety information, warnings, and instructions are read and understood before any
operation or any maintenance procedures are performed.

The user is responsible for the performance of maintenance. All adjustments, the use of proper
lubricants, fluids, filters, and the replacement of components due to normal wear and aging are
included. Failure to adhere to proper maintenance intervals and procedures may result in
diminished performance of the product and/or accelerated wear of components.

Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST,
in order to determine the maintenance intervals. Products that operate in severe operating
conditions may require more frequent maintenance. Refer to the maintenance procedure for any
other exceptions that may change the maintenance intervals.

Note: Before each consecutive interval is performed, all maintenance from the previous interval
must be performed.

Note: If Cat HYDO Advanced hydraulic oils are used, the hydraulic oil change interval is
extended to 4000 hours or 2 years. S·O·S services may extend the oil change even longer, to 6000
hours or 3 years. Consult your Cat dealer for details.

When Required

Blade Lift Cylinder Socket - Check/Adjust/Replace


Brake Accumulator - Check
Cab Air Filter - Clean/Replace
Centershift Cylinder Socket - Check/Adjust/Replace
Circle Clearances - Check/Adjust
Circuit Breakers - Reset
Cooling Cores - Clean
Cutting Edges and End Bits - Inspect/Replace
Display and Camera - Clean
Drawbar Ball and Socket End Play - Check/Adjust
Engine Air Filter Element - Clean/Replace

https://192.168.0.142:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 30-Nov-20
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4... Page 2 of 4

Engine Compartment - Clean


Ether Starting Aid Cylinder - Replace
Film (Product Identification) - Clean
Fuel System - Fill
Fuel System - Prime
Fuel Tank Water and Sediment - Drain
Fuses - Replace
Moldboard Wear Strip - Inspect/Adjust/Replace
Oil Filter - Inspect
Ripper Tip - Inspect/Replace
Scarifier Teeth - Inspect/Replace
Window Washer Reservoir - Fill

Every 10 Service Hours or Daily

Backup Alarm - Test


Brakes, Indicators and Gauges - Test
Circle Drive Pinion Teeth - Lubricate
Circle Top - Lubricate
Cooling System Coolant Level - Check
Engine Oil Level - Check
Fuel System Water Separator - Drain
Hydraulic System Oil Level - Check
Seat Belt - Inspect
Transmission and Differential Oil Level - Check

Every 100 Service Hours or 2 Weeks

Articulation Bearings - Lubricate


Axle Oscillation Bearings - Lubricate
Blade Lift Cylinder Socket - Lubricate
Centershift Cylinder Socket - Lubricate
Centershift Lock Bar - Clean/Lubricate
Drawbar Ball and Socket - Lubricate
Kingpin Bearings - Lubricate
Ripper Cylinder Bearings - Lubricate
Scarifier Lift Link Socket - Lubricate
Secondary Steering - Test
Steering Cylinder Ends and Tie Rods - Lubricate
Tire Inflation - Check
Wheel Lean Bearings - Lubricate
Work Tool Lift - Lubricate

Initial 250 Service Hours (or at first oil change)

Gear Group (All Wheel Drive) Oil - Change

Every 250 Service Hours

Engine Oil Sample - Obtain

https://192.168.0.142:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 30-Nov-20
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4... Page 3 of 4

Every 500 Service Hours or 3 Months

All Wheel Drive Motor Supply Hose - Inspect/Replace


Belts - Inspect/Adjust/Replace
Braking System - Test
Cooling System Coolant Sample (Level 1) - Obtain
Engine Crankcase Breather - Replace
Engine Oil and Filter - Change
Engine Shutdown Switch - Check
Fuel System Filter - Replace
Fuel Tank Cap and Strainer - Clean
Gear Group (All Wheel Drive) Oil Level - Check
Gear Group (All Wheel Drive) Oil Sample - Obtain
Hydraulic System Oil Sample - Obtain
Oil Filter (Hydraulic Tank Return) - Replace
Oil Filter (Implement Controls) - Replace
Tandem Breather - Clean/Replace
Tandem Drive Oil Level - Check
Tandem Drive Oil Sample - Obtain
Transmission and Differential Oil Sample - Obtain
Wheel Bearing Oil Level (Front) - Check
Wheel Bearing Oil Sample (Front) - Obtain

Every 1000 Service Hours or 1 Year

Oil Filter (All Wheel Drive) - Replace


Rollover Protective Structure (ROPS) - Inspect
Transmission and Differential Oil - Change
Transmission and Differential Oil Filter and Screens - Replace/Clean

Every 2000 Service Hours or 2 Years

Battery or Battery Cable - Inspect/Replace


Circle Drive Oil - Change
Cooling System Coolant Sample (Level 2) - Obtain
Cooling System Pressure Cap - Clean/Replace
Crankshaft Vibration Damper - Inspect
Gear Group (All Wheel Drive) Oil - Change
Tandem Drive Oil - Change
Wheel Bearing Oil (Front) - Change

Every 2500 Service Hours

Engine Valve Lash - Check


Engine Valve Rotators - Inspect

Every 3 Years

Seat Belt - Replace

https://192.168.0.142:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 30-Nov-20
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4... Page 4 of 4

Every 6000 Service Hours or 3 Years

Cooling System Coolant Extender (ELC) - Add


Hydraulic System Oil - Change

Every 12 000 Service Hours or 6 Years

Cooling System Coolant (ELC) - Change

https://192.168.0.142:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/... 30-Nov-20

You might also like