Scribd
Upload
194 views

Design of Two-Way Slab: Structural Calculation Residential Building

This engineering report provides the design of a two-way slab for a proposed two storey residential building. It includes the design parameters, support conditions, design loads, moment coefficients, slab reactions, ductility requirements, and the calculations to determine the required and used reinforcement for the negative and positive moments along the shorter and longer dimensions of the slab. The slab is designed with 10mm diameter bars spaced at 200mm to satisfy the ductility requirements at all locations.

Uploaded by

Glenn Mark Dagohoy
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
194 views

Design of Two-Way Slab: Structural Calculation Residential Building

This engineering report provides the design of a two-way slab for a proposed two storey residential building. It includes the design parameters, support conditions, design loads, moment coefficients, slab reactions, ductility requirements, and the calculations to determine the required and used reinforcement for the negative and positive moments along the shorter and longer dimensions of the slab. The slab is designed with 10mm diameter bars spaced at 200mm to satisfy the ductility requirements at all locations.

Uploaded by

Glenn Mark Dagohoy
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

Engineering Report PROPOSED TWO STOREY

Structural Calculation RESIDENTIAL BUILDING

DESIGN OF TWO-WAY SLAB


Slab Design S-1

DESIGN PARAMETERS
f'c = 20 MPa Compressive strength of concrete
fy = 227 MPa Yield strength of steel bar
Ø= 10 mm Bar diameter
t= 100 mm Thickness of slab
L= 3.75 m Longer dimension of slab
B= 3.75 m Shorter dimension of slab

smax = 200 Maximum spacing of reinforcement


b= 1000 Width of slab
d= 75 Effective depth of slab

SUPPORT CONDITIONS
CASE 1 CASE 2 CASE 3 CASE 4 CASE 5 CASE 6 CASE 7 CASE 8 CASE 9

DESIGN LOADS If m > 0.5 is Two Way Slab


Live Load = 1.90 KPa Ratio(B/L) = 1.00
Ceiling = 0.20 KPa m = 1.00 < < Manual Input !!!
Utilities = 0.10 KPa
Topping = 0.60 KPa
Flr Fin = 0.77 KPa
Mov. Part = 0.50 KPa
Others = 0.00 KPa
Slab = 2.40 KPa
Total DL = 4.57 KPa

MOMENT COEFFICIENTS
-CaDL = 0.061 Negative moment coefficient along the shorter dimension due to dead load
-CaLL = 0.061 Negative moment coefficient along the shorter dimension due to live load
-CbDL = 0.033 Negative moment coefficient along the longer dimension due to dead load
-CbLL = 0.033 Negative moment coefficient along the longer dimension due to live load
+CaDL = 0.023 Positive moment coefficient along the shorter dimension due to dead load
+CaLL = 0.030 Positive moment coefficient along the shorter dimension due to live load
+CbDL = 0.020 Positive moment coefficient along the longer dimension due to dead load
+CbLL = 0.028 Positive moment coefficient along the longer dimension due to live load

SLAB REACTIONS DUCTILITY REQUIREMENTS


WaDL = 0.5CaDLWDLLa rmax =0.75 [ 600b1f'c ]
= 5.741 kN/m fy(600 + fy)
WaLL = 0.5CaLLWLLLa = 0.04075
= 2.387 kN/m rmin = 1.4/fy
= 0.0062
WbDL = 0.5CbDLWDLLb rmin = (f'c)0.5/4fy
= 2.828 kN/m = 0.0049
WbLL = 0.5CbLLWLLLb rmin = 0.0062 governs
= 1.176 kN/m

LOCATION EQUATIONS MOMENT MTOTAL rreqd rused Spacing Sfinal Ductility Rebar spacing, mm
Negative -CaDLWuDLLa
2
4.70
Moment, Ma -C W L 2 7.31 0.00666 0.0067 157 157 PASS 10 mm diameter @ 150 mm
aLL uLL a 2.61
Negative -CbDLWuDLLb
2
2.54
Moment, Mb -C W L 2 3.96 0.003525 0.0047 223 200 PASS 10 mm diameter @ 200 mm
bLL uLL b 1.41
Positive +CaDLWuDLLa
2
1.77
Moment, Ma +C W L 2 3.06 0.002708 0.0036 291 200 PASS 10 mm diameter @ 200 mm
aLL uLL a 1.28
Positive +CbDLWuDLLb
2
1.54
Moment, Mb +C W L 2 2.74 0.002423 0.0032 325 200 PASS 10 mm diameter @ 200 mm
bLL uLL b 1.20

You might also like