Scribd
Upload
58 views

Application Guide Jotafloor Topcoat: Acceptable Environmental Conditions - Before and During Application

This document provides application guidelines for Jotafloor Topcoat, a marine paint product supplied by SML Marine Paints. It instructs the user to mix the two components of the product for at least 4 minutes until homogenous. It then recommends applying two coats of the product at a rate of 100 microns per coat, allowing it to dry between coats. Environmental conditions for application are also specified, including acceptable temperature and humidity ranges. Information on product mixing ratios, induction time, pot life, and thinner are also provided.

Uploaded by

TamerTamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
58 views

Application Guide Jotafloor Topcoat: Acceptable Environmental Conditions - Before and During Application

This document provides application guidelines for Jotafloor Topcoat, a marine paint product supplied by SML Marine Paints. It instructs the user to mix the two components of the product for at least 4 minutes until homogenous. It then recommends applying two coats of the product at a rate of 100 microns per coat, allowing it to dry between coats. Environmental conditions for application are also specified, including acceptable temperature and humidity ranges. Information on product mixing ratios, induction time, pot life, and thinner are also provided.

Uploaded by

TamerTamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

SUPPLIED BY SML MARINE PAINTS - TEL: 01285 862 132 - WEB: WWW.SMLMARINEPAINTS.CO.

UK

Application Guide
Jotafloor Topcoat

traces of dust ot other loose material.

Using a slow speed drill (300-400 RPM) mix the two components of the product together for a minimum of 4
minutes until it becomes homogenous.

The applicator must ensure that there is sufficient supply of paint materials and labour, to carry out the
continuous application in any given floor area.

Apply the first coat of the product on the Jotafloor Primer, using a roller, brush or airless spray at a rate of 100
microns, W.F.T. ensuring that the surface is fully covered and that no ponding of the material occurs. Allow it to
dry.
Apply the second coat of the product, using a roller, brush or airless spray at a rate of 100 microns, W.F.T.
ensuring that the surface is fully covered and that no ponding of the material occurs. Allow it to dry.
The above thicknesses are for demonstration purpose only. All the thicknesses are determined by the
specification of each individual product.

Acceptable environmental conditions - before and during application

Air temperature 10 - 40 °C
Substrate temperature 10 - 40 °C
Relative Humidity (RH) 10 - 85 %

• Only apply the coating when the substrate temperature is at least 3 °C (5 °F) above the dew point
• Do not apply the coating if the substrate is wet or likely to become wet
• Do not apply the coating if the weather is clearly deteriorating or unfavourable for application or curing
• Do not apply the coating in high wind conditions

Product mixing
4/16 1/4
Product mixing ratio (by volume)

Jotafloor Topcoat Comp A 4 part(s)


Jotafloor Topcoat Comp B 1 part(s)

No part mixing of this product.


Use a slow speed drill and mixing paddle. Pour the full contents of the mixed material onto the floor immediately
after mixing is completed.
The temperature of base and curing agent is recommended to be 18 °C or higher when the paint is mixed.

Induction time and Pot life

Paint temperature 23 °C

Induction time 10 min


Pot life 2h

The temperature of base and curing agent is recommended to be 18 °C or higher when the paint is mixed.

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Date of issue: 20 January 2019 Page: 2/6

This Application Guide supersedes those previously issued.


The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety
Data Sheet (SDS) for all the products used as part of the coating system.
For your nearest local Jotun office, please visit our website at www.jotun.com.

FOR FREE ADVICE AND TRADE PRICES CONTACT SML MARINE PAINTS

You might also like