Scribd
Upload
155 views

Uwave PSV Metr - EN PDF

The document describes the design and construction of an SWR meter for measuring standing wave ratios from 144-1296 MHz. The SWR meter consists of a directional coupler made from two pieces of semirigid coaxial cable with overlapping gaps, two detectors that convert RF energy to DC voltage, and a display unit with two analog meters. Measured parameters show the SWR meter can accurately measure standing wave ratios down to 1.21 at 144 MHz and up to 1.54 at 1296 MHz. The SWR meter also has a power range of 3 watts to 4 kilowatts depending on the frequency.

Uploaded by

Nenad Momcilovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
155 views

Uwave PSV Metr - EN PDF

The document describes the design and construction of an SWR meter for measuring standing wave ratios from 144-1296 MHz. The SWR meter consists of a directional coupler made from two pieces of semirigid coaxial cable with overlapping gaps, two detectors that convert RF energy to DC voltage, and a display unit with two analog meters. Measured parameters show the SWR meter can accurately measure standing wave ratios down to 1.21 at 144 MHz and up to 1.54 at 1296 MHz. The SWR meter also has a power range of 3 watts to 4 kilowatts depending on the frequency.

Uploaded by

Nenad Momcilovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

SWR meter for 144-1296 MHz bands

(Honza OK1TIC, [email protected])

PREFACE
During my experiments on UHF and lower microwave bands I faced a problem
of accurate measurement of standing wave ratio coefficient. Commercial SWR-meters are rarely
available or are not precise enough on these bands or are too expensive. Thus I decided to build
my own SWR-meter. But what type? From my previous experiments with directional couplers
I came to the conclusion that planar directional couplers are not suitable enough for this
application. They suffer from several vices and their construction is pretty complicated. Thus
I was searching an inspiration elsewhere. An idea of SWR-meter which I´m going to describe
in this article belongs to Paul G7EYT. Refer to [1].

OVERALL CONCEPT
Schematic diagram of the SWR-meter is depicted in fig. 1. It can be seen that the SWR
meter consists of three main parts: directional coupler, two detectors and display unit. Directional
coupler is used to decouple a piece of energy from incident and reflected wave. Detectors convert
this RF energy to direct current which is thad displayed in the display unit. All these parts are
further described in this chapters. Following chapters are showing my construction of the SWR
meter.

Fig. 1: SWR meter schematic diagram


Directional Coupler:
Directional coupler is made of two pieces of semirigid coaxial transmission line with
outer diameter of 3,5mm. Both lines have a longitudal gap filed in their shieldings so that the
inner conductors are uncovered. The gaps are 60mm long and 1mm wide (Paul is using 30x2mm
gap [1]. But his directional coupler is used for ISM band thus is half the length.) Both lines are
pressed and soldered together so that the gaps overlap. This ensures coupling between both lines
while keeping their characteristic impedances almost unchanged. Futhermore the coaxial concept
ensures low radiation, good transmission between the connectors and coaxial coupler itself and
thereby low insertion loss and low input and output reflection coefficients.

Detectors:
The detectors also follows Paul‘s concept [1]. The only difference is in used detection
diodes. We can say that almost any microwave schottky diode with low barrier voltage can be
used. I used some unknown type from discarded radiocommunication device. You can use
a package with two integrated diodes (my case), two diodes in two packages or also a single
diode (one-way rectifier) whose sensitivity is worse. We can estimate that the sensitivity
of a single diode rectifier will be 6dB lover (half voltage) that in case of two-diode rectifier which
is a significant value.
Furthermore both detectors should use the same detection diodes (same all components)
to guarantee proper undistorted measurement.

Display unit:
In my construction I used widely used concept of two analogue meters with potentiometer
for sensitivity adjustment. Meter connected to detector #1 is showing forward power, meter
connected to detector #2 is showing reflected power. If we set the potentiometer so that the
forward meter is showing full range the second meter (reflected power) will show us directly the
SWR value (we must have the second meter calibrated to SWR).

FABRICATION OF DIRECTIONAL COUPLER


The directional coupler looks simple but its construction is not so easy and
straightforward. I’ll try to describe here some hints and recommendations.
The only suitable transmission line for this application is the „pipe“ semirigid coaxial line.
The transmission line whose outer conductor is made of a tin-plated net known from standard
flexible coaxials is not suitable. It is hard to file such a coaxial line.
First of all you have to prepare both pieces of semirigid. Cut them on an appropriate
length (60mm for gap + length needed for connectors) and prepare all four ends for connector
attachment. Do not mount the connectors right now, they will cool the transmission line while
soldering the gaps together. Line up both coaxials, measure out 60mm in the middle for the gaps
and bend slightly all ends. It is too risky to bend the lines after filing - you can deform them
easily. Then solder the lines in the middle (if you also use an aluminium coaxial it is good to use
a soldering liquid for Al) fix them in the vice and file the gaps in the middle. The dimensions
of gaps should be approximately 60x1mm but based on my measurement this is not a strict
requirement. The length should be 50 to 70mm if you want to use 144 to 1296MHz bands. The
width of the gaps also isn’t crutial. If you use wider gaps the inner conductors will be less spaced
from each other thereby reaching higher coupling coefficient. The SWR-meter will be then more
sensitive and will work with weaker signals.
It looks like a small fimbriation at the edges of the gaps does not affect resulting
parameters.
After both gaps are filed you can solder the lines together. Take care of good overlap
of the gaps! Finaly solder the connectors. My construction of the directional coupler is shown
on figure 2.

Fig. 2: My construction of the directional coupler

FABRICATION OF THE DETECTORS


As it was stated above I used SMA male connectors for the coupling line. So the detectors
are mounted on the female panel SMA connector. This way you can easily remove the detectors
from the directional coupler and do some measurements is suitable measurement instruments are
available.
The components of the detector are directly soldered on the connector body without any
printed circuit board. This way all the parasitic parameters are minimized and we can assume that
the detector will work fine on higher frequencies as well.
I used 0603 chip resistors and capacitors. (I guess Paul [1] is using 0805.) The values
follow: C1, C3, C5, C7: 100pF; C2, C4, C6, C8: 560pF; R1, R2, R3, R4: 100; R5, R6, R7, R8:
10k; R9, R10: 22k/lin/stereo. As I mentioned earlier I used some unknown schottky diodes.
I assume that a diode like BAT-15 will perform identically. The detector is depicted on firuge 3.
Fig. 3: The detector

MODIFICATION OF THE OLD SWR-METER


I mounted all the SWR meter into an „old“ unused commercial SWR-meter. So I reused
the enclosure together with two analogue meters that were calibrated to SWR. My realization is
shown on figures 4 and 5.
Fig. 4: Front view of my SWR-meter

Fig. 5: Rear view into the SWR-meter interior


MEASURED PARAMETERS
Graph of coupling coefficient (desired transfer between the main and coupling
transmission line – s31 from fig. 1) and isolation (undesired transfer between the main and
coupling transmission line – s41 from fig. 1) is captured at figures 6 and 7. It is desired that the
difference between the isolation and coupling coefficient (thus the directivity) is as high
as possible because this value determines the lower level of SWR that the device is able
to measure without significant error. As it can be seen from graphs 6 and 7 the value of directivity
at amateur bands is:
• 144 MHz: 26,5 dB
• 432 MHz: 24,6 dB
• 1296 MHz: 19,4 dB.
Because the desired signal detected on the coupling line should be stronger than the
undesired one, one can expect that the lower limit of reflection coefficient indicated without
significant error is -20,5 dB for 144 MHz, -18,6 dB for 432 MHz and -13,4 dB for 1296 MHz.
In terms of SWR this means 1,21 for 144 MHz, 1,27 for 432 MHz and 1,54 for 1296 MHz. If we
measure SWR that is lower than these values the error becomes unacceptable. On frequencies
above 1,5 GHz the value of directivity is too low and the SWR-meter can not be used here. If you
want to use the SWR-meter on higher frequencies you have to fabricate a directional coupler with
shorter gap.

Fig. 6: Coupling coefficient (s31)


Fig. 7: Isolation (s41)

As for the lower power limit of the SWR-meter the transfer characteristic of used
detectors must be known. In my case this is captured in table 1.

Tab. 1: Transfer characteristics of the detector (first row: input power in dBm, first column:
frequency in MHz)

Supposing the resistance of used analogue meter to be in range of 400 to 1000 ohm (full
scale is excited by 100uA current) that a voltage as low as 60 mV can excite the meter to its full
scale. Based on table 1 this voltage can be generated by a signal whose power is -10dBm.
If we further take into consideration figure 6 than we can make a conclusion that the SWR-meter
should be capable to fully operate with signals as low as 35 dBm (~ 3 W) at 144 MHz, 25 dBm
(~ 0,3 W) at 432 MHz and 22 dBm (~ 0,15 W) at 1296 MHz. The truth is that the reality has
proven slightly higher values - e.g. 1 W at 432 MHz.

As for the upper power limit this is given by reverse voltage of diode used in the
detectors. If we suppose this value to be 4V (example for BAT-15) and if we further take into
consideration table 1 than we can deduce that the detector can handle signals up to 22dBm
approximately. Recalculated to the input of the directional coupler it makes 66dBm
(approximately 4kW) for 144MHz, 57dBm (500W) for 432 MHz and 54dBm (~250W) for
1296MHz. But it is doubtful if the rest of the SWR-meter will be able to withstand such a high
power (4kW).
Please notice that all introduced calculations are just only rough estimates.
Further measurements are showing that the insertion loss of the SWR-meter is well below
0,2dB for frequencies up to 1,8GHz and reflection coefficient is better than -25dB for frequencies
up to 2GHz. More measurements can be found in [2].

CONCLUSION
This article described a construction of an easy-to-build SWR-meter that is suitable
mainly for UHF and SHF frequencies. Based on measured data it can be seen that such an
SWR-meter is fully sufficient for ham radio purposes.
I wish good luck to all of you that decided to build this SWR-meter.

73, Honza.

USED LITERATURE
[1] http://www.frars.org.uk/cgi-bin/render.pl?pageid=1085
[2] www.radioamater.cz nebo http://ok1tic.nagano.cz

You might also like