Scribd
Upload
413 views10 pages

User Manual Happylightshow Vectra C / Signum

This document is a user manual for the Happylightshow device that can be installed in Vectra C and Signum vehicles. It communicates through the CAN-Bus to enable additional lighting functions. It is easily installed by connecting it to the diagnostic port and requires no wiring. The manual describes setting up the device by using pedals and switches to select lighting options and functions like welcome lighting, speed-based locking, and cornering lights. However, the device does not have legal approval for use on public roads.

Uploaded by

Aivaras Miliūnas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
413 views10 pages

User Manual Happylightshow Vectra C / Signum

This document is a user manual for the Happylightshow device that can be installed in Vectra C and Signum vehicles. It communicates through the CAN-Bus to enable additional lighting functions. It is easily installed by connecting it to the diagnostic port and requires no wiring. The manual describes setting up the device by using pedals and switches to select lighting options and functions like welcome lighting, speed-based locking, and cornering lights. However, the device does not have legal approval for use on public roads.

Uploaded by

Aivaras Miliūnas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

User Manual Happylightshow

Vectra C / Signum

Happylightshow Vectra 1
116
Übersicht

1. Introduction..............................................................3

2. Installation
2.1 Vectra C / Signum..................................................4
2.2 Function Test.........................................................5

3. Setup........................................................................6

4. Functional Description..............................................8

5. Legal Meaning.........................................................10

Happylightshow Vectra 2
116
1.Introduction

The HAPPYLIGHTSHOW is a additional electronical


device, that communicates through the on-board
CAN-Bus system.
Therefore additional new functions are possible.

The HAPPYLIGHTSHOW is very easy to install,


because it‘s only being put on the diagnostic link
connector (DLC).

-> No wiring or soldering necessary

Happylightshow Vectra 3
116
2.1 Einbau Vectra C / Signum

mounting place:
diagnostic link connector (DLC) behind the ashtray

procedure:

The Happylightshow will be mounted with the long side


downwards(see figure)

Happylightshow Vectra 4
116
2.2 Function Test

Activate the ignition.

If the installation was sucessful the LEDs on the


HAPPYLIGHTSHOW will work like this:

Green Led always on


Red Led toggeling every second

→ Installation sucessful, go on with setup procedure

Happylightshow Vectra 5
116
3.Setup Vectra C / Signum

1 Activating Setup
Requirements: Ignition on, Engine off, Lightswitch off and no Clutch pressed.

Procedure:
Push Brake, FlashToPass and TurnSwitchLeft at the same time

Advice:
Best way to do it is: Push Brake and FlashToPass together and then add
TurnSwitchLeft.

-> Right Turn Telltale within the Instrument will light up.

2 Adjustments
The Speedometer shows the digit (Right Turn Telltale lights up)
To switch between each digit push Brake (0km/h = digit0, 10km/h = digit1)

To change the value of each digit you have to change into the revolution counter
By pushing the Clutch (Left Turn Telltale lights up).
Now change the value by pushing the Brake pedal (0rpm = 0, 1000rpm = 1, ...).

To change back into the Speedometer use Clutch again.

For automatic cars use Parklightswitch (on/off) instead of the Clutch.

3 Save Adjustments
After setting up the happylightshow with all desired functions, use
TurnSwitchRight once to save the adjusments and go to normal mode.
The red LED on the device will toggle fast

Setup is now finished

Happylightshow Vectra 6
116
3.Setup Vectra C / Signum

4 Meaning

Digit 0: (OPC Scan)


0 = OPC Scan off
1 = OPC Scan on example:(0km/h – 1000rpm)

Digit 1: (Speedlock)
0 = Speedlock off
1 = Speedlock 1 on
2 = Speedlock 2 on

Digit 2: (WTTC rear)


0 = no lights
1 = Reverse Light + License Plate
2 = Turnlights + License Plate
3 = Brake Lights
4 = Reverse Light + 3. Brake Light
5 = Turnlights + Reverse Light
6 = Turnlights + Reverse Light + 3. Brake Light + License Plate

Digit 3: (WTTC front)


0 = no lights
1 = Park Light + Fog Lamp
2 = Turn Lights + Repeater + Fog Lamp
3 = Highbeam + Park Light + Fog Lamp
4 = Park Light
5 = Turn Lights + Repeater
6 = Highbeam + Park Light

Digit 4: (WTTC time)


0 = ca. 10s
1 = ca. 25s
2 = ca. 45s
3 = ca. 55s

Digit 5 (WTTC Activation)


0 = always when Door gets locked / unlocked
1 = only when door gets locked / unlocked twice

Digit 6 (Cornering Lights – Daytime Running Lights)


0 = off
1 = Cornering Lights (Fog Lamp) Happylightshow Vectra 7
2 = Daytime Running Lights (Fog Lamp)
116
3 = Daytime Running Lights + Cornering Lights (Fog Lamp)
4.Functional Description

Lightshow:

Requirements:Ignition on, engine off

Procedure:
Push Brake, FlashToPass and TurnSwitchLeft at the same time.

Advice:
Best way to do it is: PushBrake and FlashToPass and then add
TurnLightLeft.

-> highbeam and turnlight telltales begin to flash

To switch between lightsamples push brake pedal, the speedometer


Shows the sample (180km/h = Sample 18)

To switch betwenn the variations use parklightswitch on/off,


Telltales inside the instrument show the variation

Variation 1 (Turn Right Telltale):


lights changing clockwise/anticlockwise

Variation 2 (High Beam Telltale):


lights clockwise

Variation 3 (High Beam Telltale + Turn Right Telltale):


lights anticlockwise

OPC-Scan:
Speedometer and tachometer go to limit and back when activating the
ignition

Happylightshow Vectra 8
116
4.Functional Description

Speedlock1:
Car gets automatically locked if faster than 20km/h.Deactivating the ignition
unlocks the car again.

Speedlock2:
Car gets automatically locked if faster than 20km/h.
Car needs to be unlocked manually.

WTTC Function:
Exterior lights light up, if car gets locked/unlocked.

Cornering Light
If Lightswitch is set to Low Beam, then the foglamp gets activated if
turnswitch is pressed (if slower than 40km/h)

Daytime Running Lights


If Lightswitch is set to “0“ (off), then the foglamp gets activated when engine
is turned on.

Happylightshow Vectra 9
116
5. Legal meaning

The devices has no general type approval,


thus it is not allowed to use it within the laws of road
traffic.

By noncompliance the user will be responsible for any


loss.

Happylightshow Vectra 10
116

You might also like