Portable Manual

iR2030/2025/2022/2018 Series

Aug 8 2007
 Application
This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair
of products. This manual covers all localities where the products are sold. For this reason, there may be information in this
manual that does not apply to your locality.

Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When
changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need
arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition
of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

Trademarks
The product names and company names used in this manual are the registered trademarks of the individual companies.

Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied, reproduced or
translated into another language, in whole or in part, without the written consent of Canon Inc.

COPYRIGHT © 2001 CANON INC.

Printed in Japan

Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential information.
 Introduction

Symbols Used
This documentation uses the following symbols to indicate special information:

Symbol Description

Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.

Indicates an item requiring care to avoid electric shocks.

Indicates an item requiring care to avoid combustion (fire).

Indicates an item prohibiting disassembly to avoid electric shocks or problems.

Indicates an item requiring disconnection of the power plug from the electric outlet.

Indicates an item intended to provide notes assisting the understanding of the topic in question.
Memo

Indicates an item of reference assisting the understanding of the topic in question.

REF.

Provides a description of a service mode.

Provides a description of the nature of an error indication.

 Introduction

The following rules apply throughout this Service Manual:

1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with refer-
ence to the timing of operation.
In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates the
direction of the electric signal.
The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the delivery unit door, which results in
supplying the machine with power.
2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low".(The voltage value, how-
ever, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, the operations of the microprocessors
used in the machines are not discussed: they are explained in terms of from sensors to the input of the DC controller PCB and from the output of the
DC controller PCB to the loads.

The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and major changes will be com-
municated in the form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service Information bulletins and be
able to identify and isolate faults in the machine."
 Contents

Contents

Chapter 1 Maintenance and Inspection

1.1 Periodically Replaced Parts ...............................................................................................................................1
1.1.1Overview .........................................................................................................................................................1
1.1.2Reader Unit.....................................................................................................................................................1
1.1.3Printer Unit ......................................................................................................................................................1
1.2 Durables and Consumables...............................................................................................................................1
1.2.1Overview .........................................................................................................................................................1
1.2.2Reader Unit.....................................................................................................................................................1
1.2.3Printer Unit ......................................................................................................................................................1
1.3 Scheduled Servicing Basic Procedure .............................................................................................................2
1.3.1Scheduled Servicing......................................................................................................................................2

Chapter 2 Standards and Adjustments

2.1 Scanning System .................................................................................................................................................3
2.1.1Procedure after Replacing the CIS (LCD type).........................................................................................3
2.1.2Procedure after Replacing the CIS (Touch panel type)...........................................................................3
2.1.3Procedure after Replacing the Copyboard Glass (With ADF) ................................................................3
2.2 Image Formation System ...................................................................................................................................3
2.2.1Procedure after Replacing the Developing Assembly .............................................................................3
2.3 Electrical Components ........................................................................................................................................3
2.3.1Procedure after Replacing the Image Processor PCB (LCD type)........................................................3
2.3.2Procedure after Replacing the Image Processor PCB (Touch panel type)..........................................3
2.3.3Procedure after Replacing the USB Memory (Touch panel type)..........................................................4
2.3.4Actions to Take before All Clearing (Backing up the User Data) ...........................................................4

Chapter 3 Error Code

3.1 Error Code Details ...............................................................................................................................................7
3.1.1Error Code Details .........................................................................................................................................7
3.2 Jam Code............................................................................................................................................................10
3.2.1Jam Codes (Related to Printer Unit).........................................................................................................10
3.2.2Jam Codes (Related to Finisher) ..............................................................................................................10
3.2.3Jam Codes (Related to ADF).....................................................................................................................10
3.2.4Jam Codes (Related to Duplex Unit) ........................................................................................................10
3.2.5Jam Codes (Related to Inner 2-way Tray)...............................................................................................11

Chapter 4 User Mode Items

4.1 User Mode Items................................................................................................................................................13
4.1.1Common Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ...............................................13
4.1.2Timer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) .....................................................13
4.1.3Adjustment/Cleaning (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ..........................................14
 Contents

4.1.4Report Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)................................................... 14

4.1.5System Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i).................................................. 14
4.1.6Copy Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)...................................................... 15
4.1.7Communication Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ................................... 15
4.1.8Printer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ................................................... 16
4.1.9Address Book Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ...................................... 17
4.1.10Recommended setting of system management information.............................................................. 18
4.1.11The Reference Information of the Department ID Management ....................................................... 18

Chapter 5 Service Mode

5.1 Fax System Service Mode............................................................................................................................... 19
5.1.1 Service Soft Switch Settings (SSSW) ..................................................................................................... 19
5.1.1.1 Outline................................................................................................................................................... 19
5.1.1.2 SSSW-SW01 ....................................................................................................................................... 19
5.1.1.3 SSSW-SW03 ....................................................................................................................................... 19
5.1.1.4 SSSW-SW04 ....................................................................................................................................... 20
5.1.1.5 SSSW-SW05 ....................................................................................................................................... 21
5.1.1.6 SSSW-SW12 ....................................................................................................................................... 21
5.1.1.7 SSSW-SW13 ....................................................................................................................................... 22
5.1.1.8 SSSW-SW14 ....................................................................................................................................... 23
5.1.1.9 SSSW-SW25 ....................................................................................................................................... 23
5.1.1.10 SSSW-SW28 ..................................................................................................................................... 24
5.1.1.11 SSSW-SW30 ..................................................................................................................................... 25
5.1.1.12 SSSW-SW33 ..................................................................................................................................... 25
5.1.1.13 SSSW-SW34 ..................................................................................................................................... 26
5.1.2 Menu Switch Settings (MENU)................................................................................................................. 27
5.1.2.1 Menu Switch Composition ................................................................................................................. 27
5.1.2.2 <No.005 NL equalizer> ...................................................................................................................... 27
5.1.2.3 <No.006 telephone line monitor> ..................................................................................................... 27
5.1.2.4 <No.007 ATT transmission level> .................................................................................................... 27
5.1.2.5 <No.008 V.34 modulation speed upper limit> ................................................................................ 27
5.1.2.6 <No.009 V.34 data speed upper limit> ............................................................................................ 27
5.1.2.7 <No.010 Frequency of the pseudo CI signal>................................................................................ 27
5.1.3 Numeric Parameter Settings (NUMERIC Param.) ................................................................................ 28
5.1.3.1 Numerical Parameter Composition .................................................................................................. 28
5.1.3.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN
transmission condition (3)>........................................................................................................................ 28
5.1.3.3 <005: NCC pause length (pre-ID code)> ........................................................................................ 28
5.1.3.4 <006: NCC pause length (post-ID code)>....................................................................................... 28
5.1.3.5 <010: line connection identification length>.................................................................................... 29
5.1.3.6 <011: T.30 T1 timer (for reception)> ................................................................................................ 29
5.1.3.7 <013: T.30 EOL timer>....................................................................................................................... 29
5.1.3.8 <016: time length to first response at time of fax/tel switchover> ............................................... 29
5.1.3.9 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time
length (short)><019: pseudo RBT signal pattern OFF time length (long)> ....................................... 29
5.1.3.10 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time
length (short)><022: pseudo CI signal pattern OFF time length (long)> ........................................... 29
5.1.3.11 <023: CNG detention level for fax/tel switchover> ...................................................................... 29
 Contents

5.1.3.12 <024: pseudo RBT transmission level at time of fax/tel switchover> ........................................29
5.1.3.13 <025: Answering machine connection function signal detection time> ....................................29
5.1.3.14 <027: V.21 low-speed flag preamble identification length> ........................................................29
5.1.3.15 <055: Acquisition period of environmental log data> ...................................................................29
5.1.3.16 <056 - 061: Count type select > ......................................................................................................29
5.1.4 Scanner Function Settings (SCANNER) .................................................................................................33
5.1.4.1 Setting of Bit Switch ............................................................................................................................33
5.1.4.2 Numeric Parameter Functional configuration..................................................................................33
5.1.4.3 <024:CIS scan position during ADF scanning> ..............................................................................34
5.1.4.4 <026:Distance from the standby position of CIS to the shading start point> .............................34
5.1.4.5 <031Vertical scan start position adjustment> .................................................................................34
5.1.4.6 <032Horizontal scan start position adjustment>.............................................................................35
5.1.4.7 <033Vertical scan magnification correction> ..................................................................................35
5.1.4.8 <035: - 036:Reader motor speed change>......................................................................................35
5.1.4.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)>
35
5.1.4.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from
ADF)> ............................................................................................................................................................35
5.1.4.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)> ..............................35
5.1.4.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)>........................35
5.1.4.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>..................................35
5.1.4.14 <046: Horizontal scan end position correction (standard:scanning on ADF)> ........................35
5.1.4.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>
35
5.1.4.16 <048: Horizontal scan magnification correction (when scanning on a document fed from
ADF)> ............................................................................................................................................................35
5.1.4.17 <193: ADF special standard-sized paper: LGL misidentification-ready>..................................35
5.1.4.18 <194: ADF special standard-sized paper: LTR misidentification-ready>..................................36
5.1.4.19 <195: ADF special standard-sized paper: LTR_R misidentification-ready> ............................36
5.1.4.20 <196: Shading Target Value (Red)>...............................................................................................36
5.1.4.21 <197: Shading Target Value (Green)> ...........................................................................................36
5.1.4.22 <198: Shading Target Value (Blue)> ..............................................................................................36
5.1.4.23 <213: XYZ correction value (X) of standard white plate> (if equipped with SEND functions)).
36
5.1.4.24 <214: XYZ correction value (Y) of standard white plate> (if equipped with SEND functions) ..
36
5.1.4.25 <215: XYZ correction value (Z) of standard white plate> (if equipped with SEND functions) ..
36
5.1.5 Printer Function Settings (PRINTER) ......................................................................................................37
5.1.5.1 Service Soft Switch Settings ..............................................................................................................37
5.1.5.2 Numeric Parameter Settings (NUMERIC Param.) .........................................................................40
5.1.5.3 Setting of Cassette (CST) ..................................................................................................................43
5.1.6 Network Parameter Settings (NETWORK) .............................................................................................43
5.1.6.1 Confirmation of contents of CA certificate .......................................................................................43
5.1.7 Setting of System Functions (SYSTEM)..................................................................................................43
5.1.7.1 Bit Switch Settings ...............................................................................................................................43
5.1.8 Registration of Accessories (ACC) ...........................................................................................................44
5.1.8.1 Accessory Registration .......................................................................................................................44
5.1.9 License Management (LMS) .....................................................................................................................44
5.1.9.1 Outline ...................................................................................................................................................44
 Contents

5.1.9.2 Method of confirming license option ................................................................................................ 45

5.1.9.3 Inactivity of the transmitted license .................................................................................................. 45
5.1.10 eRDS Parameter Settings (E-RDS)....................................................................................................... 46
5.1.10.1 Settings Related to e-RDS .............................................................................................................. 46
5.1.11 Display of Counter Information (COUNTER) ....................................................................................... 46
5.1.11.1 Counters ............................................................................................................................................. 46
5.1.11.2 Clearing Counters ............................................................................................................................. 47
5.1.12 Report Output (REPORT) ....................................................................................................................... 47
5.1.12.1 Report Output .................................................................................................................................... 47
5.1.12.2 System Data List ............................................................................................................................... 47
5.1.12.3 System Dump List ............................................................................................................................. 48
5.1.12.4 Counter List........................................................................................................................................ 49
5.1.12.5 Error Log List ..................................................................................................................................... 49
5.1.12.6 Spec List ............................................................................................................................................. 51
5.1.12.7 Service Label ..................................................................................................................................... 54
5.1.12.8 e-RDS Communication Error Log List ........................................................................................... 54
5.1.12.9 Environmental Log Report ............................................................................................................... 54
5.1.13 Download (DOWNLOAD)........................................................................................................................ 55
5.1.13.1 Download............................................................................................................................................ 55
5.1.14 Data Initialization Mode (CLEAR) .......................................................................................................... 55
5.1.14.1 Clear.................................................................................................................................................... 55
5.1.15 Error Display (ERROR DISPLAY).......................................................................................................... 55
5.1.15.1 Error Display ...................................................................................................................................... 55
5.1.16 Display of ROM Information (ROM)....................................................................................................... 56
5.1.16.1 ROM Display...................................................................................................................................... 56
5.1.17 Test Mode (TEST MODE) ....................................................................................................................... 56
5.1.17.1 Outline................................................................................................................................................. 56
5.1.17.2 Test Mode Menu List (LCD Type) .................................................................................................. 56
5.1.17.3 Test Mode Menu List (Touch Panel Type).................................................................................... 58
5.1.17.4 D-RAM Test<(1) D-RAM TEST> .................................................................................................... 60
5.1.17.5 Scan Test ((2) SCAN TEST) ........................................................................................................... 61
5.1.17.6 Print Test ((3) PRINT TEST) ........................................................................................................... 61
5.1.17.7 Modem Test ((4) MODEM TEST)................................................................................................... 61
5.1.17.8 Function Test ((6) FUNCTION TEST) ........................................................................................... 63
5.1.17.9 Roller cleaning mode ((0) ROLLER CLEAN)................................................................................ 67

Chapter 6 Outline of Components

6.1 Clutch/Solenoid ................................................................................................................................................. 69
6.1.1List of Clutches/Solenoids ........................................................................................................................ 69
6.2 Motor ................................................................................................................................................................... 69
6.2.1List of Motors ............................................................................................................................................... 69
6.3 Fan ...................................................................................................................................................................... 71
6.3.1List of Fans................................................................................................................................................... 71
6.4 Sensor................................................................................................................................................................. 71
6.4.1List of Sensors ............................................................................................................................................. 71
6.5 Switch.................................................................................................................................................................. 73
6.5.1List of Switches............................................................................................................................................ 73
6.6 Lamps, Heaters, and Others ........................................................................................................................... 74
 Contents

6.6.1List of Lamps, Heaters, and Others ..........................................................................................................74

6.7 PCBs....................................................................................................................................................................76
6.7.1List of PCBs ..................................................................................................................................................76

Chapter 7 System Construction

7.1 System Construction .........................................................................................................................................79
7.1.1Pickup/Delivery/Original Handling Accessories System Configuration (iR2018) ..............................79
7.1.2Pickup/Delivery/Original Handling Accessories System Configuration (iR2018i) .............................81
7.1.3Pickup/ Delivery /Original Handling Accessories System Configuration (iR2022/iR2022N/iR2025/
iR2030) ..............................................................................................................................................................82
7.1.4Pickup/Delivery/Original Handling Accessories System Configuration (iR2022i/iR2022K/iR2025i/
iR2030i) .............................................................................................................................................................83
7.1.5Reader Heater/Cassette Heater System Configuration (iR2018/iR2022/iR2022N)..........................84
7.1.6Reader Heater/Cassette Heater System Configuration (iR2018i) .......................................................85
7.1.7Reader Heater/Cassette Heater System Configuration (iR2022K/iR2022i/iR2025/iR2025i/iR2030/
iR2030i) .............................................................................................................................................................86
7.1.8Printing/Transmitting Accessories System Configuration (iR2018/ir2022/iR2022N) ........................87
7.1.9Printing/Transmitting Accessories System Configuration (iR2018i/iR2022i/iR2022K/iR2025/
iR2025i/iR2030/iR2030i).................................................................................................................................88
7.1.10Functions of the Printing/Transmission Functions (iR2018/iR2022/iR2022N).................................89
7.1.11Functions of the Printing/Transmission Functions (iR2018i/iR2022i/iR2022K/iR2025/iR2025i/
IR2030/iR2030i) ...............................................................................................................................................89
7.2 Product Specifications ......................................................................................................................................89
7.2.1Product Specifications ................................................................................................................................89
7.3 Function List .......................................................................................................................................................90
7.3.1Printing Speed (iR2030/iR2030i)...............................................................................................................90
7.3.2Printing Speed (iR2025/iR2025i)...............................................................................................................92
7.3.3Printing Speed (iR2022/iR2022i/iR2022K/iR2022N)) ............................................................................93
7.3.4Printing Speed (iR2018/iR2018i/iR2018N) ..............................................................................................94
7.3.5Types of Paper .............................................................................................................................................95

Chapter 8 Upgrading
8.1 Upgrading............................................................................................................................................................97
8.1.1Overview of Upgrade (LCD type) ..............................................................................................................97
8.1.2Overview of Upgrade (Touch panel type) ................................................................................................97
8.1.3Overview of Service Support Tool (LCD type) ........................................................................................98
8.1.4Overview of Service Support Tool (Touch panel type) ..........................................................................98
 Chapter 1

Chapter 1 Maintenance and Inspection

1.1 Periodically Replaced Parts

1.1.1 Overview
0017-5958

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The machine has parts that must be replaced on a periodical basis to ensure a specific level of functional performance. (The loss of the function of any of these parts
will significantly affect the machine performance, regardless of the presence/absence of external changes or damage.)
If possible, schedule the replacement so that it coincides with a scheduled service visit.

The timing of replacement may vary depending on the site environment or user habit.

1.1.2 Reader Unit

0017-5959

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The reader unit does not have parts that require periodical replacement.

1.1.3 Printer Unit

0017-5961

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The printer unit does not have parts that require periodical replacement.

1.2 Durables and Consumables

1.2.1 Overview
0017-5962

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The machine has parts that may require replacement once or more during the period of product warranty because of wear or damage. Replace them as needed by
referring to their indicated estimated lives.
- Checking the Timing of Replacement
Use the following service mode item to check the timing of replacement:
#COUNTER > DRBL-1
- FX-UNIT: Fixing Unit
- TR-ROLL: Transfer roller
- DV-UNIT-C: Developing unit
- M-PU-RL: Manual feed pickup roller
- M-SP-PD: Manual feed separation pad

1.2.2 Reader Unit

0017-5964

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The reader unit does not have parts that are classified as durables.

1.2.3 Printer Unit

0017-5967

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

1
 Chapter 1

As of Jun. 2007
Ref. Parts name Parts No. Q'ty Life Remarks
[1] Cassette feed roller FF6-1621-000 1 100K The 2-stage cassette type uses two rollers.
[2] Cassette separation roller FF6-1621-000 1 100K The 2-stage cassette type uses two rollers.
[3] Manual feed pickup roller FL2-3202-000 1 150K
[4] Manual feed separation pad FL2-3201-000 1 150K
[5] Devrloping unit FM2-3286-000 1 150K
[6] Transfer roller FC6-4313-000 1 150K
[7] Fixing unit (100V) FM3-3652-000 1 150K
Fixing unit (120V) FM3-3651-000 1 150K
Fixing unit (230V) FM3-3650-000 1 150K

The value is the mean value collected from the results of evaluation. The parts number may change because of changes in design.

[7]

[3]

[4]

[6]

[5]

[1]
[2]
F-1-1

1.3 Scheduled Servicing Basic Procedure

1.3.1 Scheduled Servicing

0017-5969

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The reader and printer unit does not have items that require scheduled servicing.

Be sure to clean the copyboard glass and the ADF reading glass during every service visit.

2
 Chapter 2

Chapter 2 Standards and lowing keys to enter the service mode:

Additional Functions key > 2 key > 8 key > Additional Functions key
5) Select "#PRINT" using the + or - key, and then press the OK key.
Adjustments 6) Select "#PRINT SW" using the + or - key, and hen press the OK key.
Confirm that the following message is displayed:
Message: #PRINT SW 001 00000000
7) Press the following keys and confirm the message:
# key > 1 key > 1 key
2.1 Scanning System Message: #PRINT SW 011 00000000
8) Position the cursor to Bit-1 (second from right) using the + or - key, and
press the 1 key, and then confirm the following message:
2.1.1 Procedure after Replacing the CIS (LCD type) Message: #PRINT SW 011 00000010
0017-5978 9) Press the OK key. Confirm that "SW 011" changes to "SW 012".
iR2018 / iR2022 Message: #PRINT SW 012 00000000
10) Press the Reset key to exit the service mode.
After replacing the contact image sensor (CIS), go through the following 11) Close the front cover. The machine will run in the developer idling
steps to perform inter-channel output correction: mode for about 1 minute.
1) Enter the service mode. 12) When the machine stops, the idling mode ends.
Sequentially press the User Mode key " ", 2 key, 8 key, and User Mode Install, the toner cartridge following the above-mentioned procedure.
key " " on the operation panel.
2) Using the arrow keys on the operation panel, display "TEST MODE". 2.3 Electrical Components
3) Press the OK key.
4) Press the 2 key. "SCAN TEST" appears.
5) Press the 1 key. 2.3.1 Procedure after Replacing the Image Processor
PCB (LCD type)
After completion of the above steps, contact sensor output correction will be 0017-5983

performed and parameters will be set automatically. iR2018 / iR2022

2.1.2 Procedure after Replacing the CIS (Touch panel If you have replaced the image processor PCB with a new one, perform the
following operations:
type) - Using the service support tool, download the latest firmware (System/
0017-5980

iR2022i / iR2025 / iR2030 / iR2018i Boot).

- Input the all value printed on the service label affixed to the rear cover.
After replacing the contact image sensor (CIS), go through the following Make the following adjustments:
steps to perform inter-channel output correction: - Correction of output between CIS channels
1) Enter the service mode. 1) Enter the service mode.
Sequentially press the Additional functions key, 2 key, 8 key, and Additional Sequentially press the User Mode key " ", 2 key, 8 key, and User Mode
functions key on the operation panel.
2) Press the arrow key on the touch panel to display "TEST MODE". key " " on the operation panel.
3) Press [OK]. 2) Using the arrow keys on the operation panel, display "TEST MODE".
4) Press the [2] key to display "SCAN TEST". 3) Press the OK key.
5) Press the [1] key to display "SHADING". 4) Press the 2 key. "SCAN TEST" appears.
6) Press [OK]. 5) Press the 1 key.
After completion of the above procedure, the contact sensor output is com-
pensated and parameters are set automatically. After completion of the above steps, contact sensor output correction will be
After completion of automatic adjustment, "OK" is displayed. performed and parameters will be set automatically.
- Read position adjustment (Stream reading: Only when the ADF is installed)
2.1.3 Procedure after Replacing the Copyboard Glass 1) Enter the service mode.
(With ADF) Press the User Mode key " ", 2 key, 8 key, User Mode key " " on the
0017-5981 operation panel of the host machine.
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i 2) Using the arrow keys on the operation panel, display "TEST MODE".
3) Press the OK key.
After replacing the copyboard glass, enter the correction values (X, Y, Z) of 4) Press the 2 key. "SCAN TEST" appears.
the standard white plate which are indicated on the back of the new copy- 5) Press the 3 key. "SHEET POS ADJ" appears.
board glass in the service mode. The optical system starts scanning. Several seconds later, automatic adjust-
Correction value (X): Service mode>#SCAN>#SCAN NUMERIC>No.213 ment of the reading position finishes and "OK" appears.
Correction value (Y): Service mode>#SCAN>#SCAN NUMERIC>No.214
Correction value (Z): Service mode>#SCAN>#SCAN NUMERIC>No.215
Also, rewrite the values on the service label.
If automatic adjustment fails, "NG" appears. Perform the following
procedure:
Clean the white roller of the DADF and the document glass of the host
820686679349 machine, and then retry auto adjustment.

correcton correcton 2.3.2 Procedure after Replacing the Image Processor

va l u e ( X ) correcton va l u e ( Z ) PCB (Touch panel type)
va l u e ( Y ) 0017-5984

iR2022i / iR2025 / iR2030 / iR2018i

F-2-1
If you have replaced the image processor PCB with a new one, perform the
following operations:
2.2 Image Formation System - Using the service support tool, download the latest firmware (System/Boot)
and language files.
2.2.1 Procedure after Replacing the Developing - Delete the languages not used at the destination (Service mode > CLEAR
> FILE SYSTEM).
Assembly - Input the all value printed on the service label affixed to the rear cover.
0017-5982
Make the following adjustments:
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i - Correction of output between CIS channels
1) Enter the service mode.
<Going through the Developer Idling Mode> Sequentially press the Additional functions key, 2 key, 8 key, and Additional
functions key on the operation panel.
2) Press the arrow key on the touch panel to display "TEST MODE".
3) Press [OK].
After replacing the developing assembly, go through the following steps in 4) Press the [2] key to display "SCAN TEST".
the developing assembly idle rotation mode before installing the toner 5) Press the [1] key to display "SHADING".
cartridge. 6) Press [OK].
After completion of the above procedure, the contact sensor output is com-
1) Plug the power cord into the outlet. pensated and parameters are set automatically.
2) Open the front cover. After completion of automatic adjustment, "OK" is displayed.
3) With the front cover open, turn on the main power switch.
4) When a message appears on the operation panel display, press the fol-

3
 Chapter 2

- Read position adjustment (Stream reading: Only when the ADF is installed) 3) Select "#SYSTEM SW" using or , and then press the OK.
1) Enter the service mode. 4) Press the following keys to display "SW003".
Sequentially press the Additional functions key, 2 key, 8 key, and Additional # > 0 key > 3 key
functions key on the operation panel. Message: #SYSTEM SW003 00001000
2) Press the arrow key on the touch panel to display "TEST MODE". 5) Check that Bit-6 (second from left) is set to set to "1". If Bit-6 is not set to
3) Press [OK].
4) Press the [2] key to display "SCAN TEST". "1", position the cursor at this bit using or and then press the 1 key.
5) Press the [3] key to display "SHEET POS ADJ". Message: #SYSTEM SW003 01001000
6) Press [OK].
The optical system starts scanning. Several seconds later, automatic adjust- 6) Press the OK key. Check that "SW003" changes to "SW004".
ment of the reading position finishes and "OK" appears. Message: #SYSTEM SW004 00000000
7) Press the Reset key to exit the service mode.
8) Turn off the main power switch, and then turn it on again.
9) Open My Computer on the PC to check that the "Removal Disk" icon is
If automatic adjustment fails, "NG" appears. Perform the following displayed.
procedure: 10) Write the user data (address_book.abk and user_data.dat) copied onto
Clean the white roller of the DADF and the document glass of the host the Desktop as described in "a. Exporting user data" over the removable
machine, and then retry auto adjustment. disk.
11) Disconnect the USB cable from the machine.
2.3.3 Procedure after Replacing the USB Memory (Touch 12) Turn off the main power switch of the machine.
13) Perform steps 1) to 4) again to reset Bit-6 of "SW003" to "0".
panel type) 14) Press the OK key. When "SW003" changes to "SW004", press the Reset
0017-5985

iR2022i / iR2025 / iR2030 / iR2018i key to exit the service mode.

15) Check the user data list output as described in "a. Exporting user data" to
If you have replaced the USB with a new one, perform the following opera- make sure that the user data has been loaded into the machine properly.
tions:
- Using the service support tool, download language files.
- Delete the languages not used at the destination (Service mode > CLEAR
> FILE SYSTEM).

MEMO:
You also need to perform these operations after formatting the damaged
USB memory.

2.3.4 Actions to Take before All Clearing (Backing up the

User Data)
0017-5986

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

- Performing the all-clear operation in the service mode (#CLEAR > ALL)
erases/initializes the user data such as address data and user mode settings.
Be sure to back up the user data with the data export function before starting
the all-clear operation, and then load the user data with tbe data import
function.
- To export and import user data, a PC and a USB cable are required. Have
them on hand.

a. Exporting user data

1) Output a user data list in the following user mode.
> Report Setting > Plint List > User Data List
2) Press the following keys to enter the service mode.

> 2 key > 8 key >

3) Select "#SYSTEM" using or , and then press the OK.
4) Select "#SYSTEM SW" using or , and then press the OK.
5) Press the following keys to display "SW003."
# > 0 key > 3 key
Message: #SYSTEM SW003 00001000
6) Position the cursor at Bit-6 (second from left) using or , and then
press the 1 key.
Message: #SYSTEM SW003 01001000
7) Press the OK key. Check that "SW003" changes to "SW004".
Message: #SYSTEM SW004 00000000
8) Press the Reset key to exit the service mode.
9) Turn off the main power switch, and then turn it on again.
10) Start the PC and connect it to this machine with a USB cable.
11) Open My Computer on the PC to check that the "Removable Disk" icon
is displayed. If the "Removable Disk" icon is not displayed, repeat the
above procedure starting with step 1.
12) Double-click the "Removable Disk" icon, and then copy the user data
(address_book.abk and user_data.dat) onto the Desktop.
13) Close the window on the Desktop.
14) Turn off the main power switch of this machine.
15) Disconnect the USB cable from this machine.

b. Importing user data

1) Press the flowing keys to enter the service mode.
> 2 key > 8 key >
2) Select "#SYSTEM" using or , and then press the OK.

4
Chapter 2

5
 Chapter 3

Chapter 3 Error Code

3.1 Error Code Details

3.1.1 Error Code Details

0017-6037

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-3-1

Display
Detail Code Main Cause/Symptom Countermeasure
Code
E000 0000 Startup error
The temperature detected by the main or sub thermistor does - Check the fixing film connector.
not rise to the specified value during startup control. - Replace the fixing film unit.
- Replace the DC controller PCB.

E001 0000 Abnormally high temperature (detected by main thermistor)

The main thermistor detected an abnormally high temperature - Check the connector of the fixing film unit.
(240 deg C) during temperature control. - Replace the fixing film unit.
- Replace the DC controller PCB.

0001 Abnormally high temperature (detected by sub thermistor)

The sub thermistor detected an abnormally high temperature - Check the connector of the fixing film unit.
(295 deg C) during temperature control. - Replace the fixing film unit.
- Replace the DC controller PCB.

E002 0000 Low temperature during temperature control.

The target temperature is not reached during temperature - Check the connector of the fixing film unit.
control. - Replace the fixing film unit.
- Replace the DC controller PCB.

E003 0000 Abnormally low temperature (detected by main thermistor)

After the temperature detected by the main thermistor has - Check the connector of the fixing film unit.
reached the specified value, it does not reach the specified value - Replace the fixing film unit.
during initial rotation. - Replace the DC controller PCB.

0001 Abnormally low temperature (detected by sub thermistor)

After the temperature detected by the sub thermistor has - Check the connector of the fixing film unit.
reached the specified value, it does not reach the specified value - Replace the fixing film unit.
during initial rotation. - Replace the DC controller PCB.

E007 0000 Fixing film sensor failure

The fixing film sensor is faulty. - Check the connector of the fixing film sensor.
- Replace the fixing film sensor.
- Replace the DC controller PCB.

E010 0000 Main motor failure

The main motor is faulty. - Check the connector of the main motor.
- Replace the main motor.
- Replace the DC controller PCB.
E019 0000 Waste toner full detection
The waste toner full state was detected. Replace the drum unit.
0001 Waster toner full detection sensor is faulty.
The waste toner full state was detected continuously for five or - Check the connector of the waster toner full sensor.
more seconds while the main motor was turning. - Replace the waste toner full sensor.
- Replace the DC controller PCB.

E052 0000 Erroneous connection to duplex unit

Disconnection of the duplex unit was detected after power-on, - Check the connectors of the duplex unit and DC controller PCB.
detection of normal connection to the duplex unit, and start of - Replace the duplex controller PCB.
communication. - Replace the DC controller PCB.

E100 0000 BD detection PCB failure

The BD detection PCB is faulty. - Check the connector of the BD detection PCB.
- Replace the laser scanner unit.
- Replace the DC controller PCB.

7
 Chapter 3

Display
Detail Code Main Cause/Symptom Countermeasure
Code
E196 0001 Image processor PCB failure
Error on writing and readout ROM of image processor PCB - Putting the switch on/off of the power supply.
(mainn ROM). - Replace the image processor PCB.

0002 Image processor PCB failure

Error on writing and readout ROM of image processor PCB - Putting the switch on/off of the power supply.
(option ROM). - Replace the image processor PCB.

E197 0000 Printer engine communication error

Erroneous communication between the DC controller PCB and - Check the connectors of the DC controller PCB and image
image processor PCB was detected. processor PCB.
- Replace the DC controller PCB for normal connection.
- Replace the image processor PCB.
E261 0000 Zero-cross signal error
If failed to detect zero-cross signal cycle of the power supply - Replace the power supply PCB.
when initializing. - Replace the DC controller PCB.
When the input of the zero-signal failed continuously for three
seconds while controlling the temperature adjustment.

E716 0000 Erroneous communication with optional cassette

Disconnection of the optional cassette was detected after - Check the connectors of the optional cassette PCB and DC
power-on, detection of normal connection to the optional controller PCB.
cassette, and start of communication. - Replace the optional cassette PCB for normal connection.
- Replace the DC controller PCB.

E719 0000 Erroneous communication with card reader (serial communication)

- Disconnection from the card reader has been detected since - Check the connectors of the card reader and image processor PCB.
communication started after confirmation of normal connection - Replace the card reader for normal connection.
to the card reader (after power-on). - Replace the image processor PCB.
- A serial communication error has occurred. (The serial
communication error cannot be recovered.)

0002 Erroneous communication with coin vendor (serial communication)

- Disconnection from the coin vendor has been detected since - Check the connection between the image processor PCB and serial
communication started after confirmation of normal connection PCB.
to the coin vendor (after power-on). - Check the connectors of the serial PCB and coin vendor for normal
- A serial communication error has occurred. (The serial connection.
communication error cannot be recovered.) - Replace the serial PCB.
- Check the coin vendor.
- Replace the image processor PCB.

E730 0000 Inside error of the image processor PCB (PDL system error)

The inside of the image processor PCB is faulty. - Putting the switch on/off of the power supply.
- Replace the image processor PCB.

E733 0000 Erroneous communication between controller and printer

Cannot communicate with the printer at startup. - Check the connectors of the DC controller PCB and image
processor PCB for normal connection.
- Check the power supply of the printer (Check whether initialization
is performed at startup).
- Replace the DC controller PCB or image processor PCB.

E736 0000 CCU communication error

The installed modem PCB is incompatible. - Check the connectors of the image processor PCB and modem.
- Replace the modem PCB.
- Replace the image processor PCB.

E739 0000 Erroneous communication between controller and network board

The installed network board is incompatible. - Check the connectors of the image processor PCB and LAN PCB
for normal connection.
- Replace the LAN PCB.
- Replace the image processor PCB.

8
 Chapter 3

Display
Detail Code Main Cause/Symptom Countermeasure
Code
E744 Language file/boot ROM/USB memory error

0001 The language file version does not match Bootable. Download a language file of the correct version.
0002 The language file is longer than the permitted size. Download a language file of the correct version.
0003 The language file version does not match Bootable. Download a language file of the correct version.
0004 Language file read error Download a language file of the correct version.
E805 0000 Fan failure
The fan is faulty. - Check the fan connector.
- Replace the fan.
- Replace the DC controller PCB.
E808 0000 Fixing drive circuit failure
- The heater does not turn on. - Check the connector of the fixing film unit.
- A fixing drive motor failure was detected. - Replace the fixing film unit.
- Replace the fixing drive motor.
- Replace the DC controller PCB.
- Replace the power supply PCB.

9
 Chapter 3

3.2 Jam Code

3.2.1 Jam Codes (Related to Printer Unit)

0017-6038

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-3-2

Code Name Sensor No. Description

0104 Delay jam in paper SR209 The registration sensor cannot detect the leading edge of paper from the moment paper pickup starts to the
pickup section moment the jam detection time is reached.
0208 Stationary jam in paper SR209 The registration sensor cannot detect the no paper status specified time before the leading edge of the picked
pickup section up paper reaches this sensor.
010c Delay jam in deliver SR202, - The fixing delivery sensor cannot detect presence of paper within the specified time after turning on of the
section SR203, registration clutch.
SR209 - The fixing delivery sensor detected absence of paper within the specified time after the sensor had detected
presence of paper within the specified time after turning on of the registration clutch.
- The No.1 delivery sensor cannot detect presence of paper within the specified time after turning on of the
fixing delivery sensor.
0210 Stationary jam in SR202, - The fixing delivery sensor cannot detect absence of paper within the specified time after turning off of the
delivery section SR203 registration clutch.
- The fixing delivery sensor cannot detect absence of paper within the specified time after the sensor detected
the leading edge of paper.
- The No.1 delivery sensor cannot detect absence of paper within the specified time after the sensor detected
the leading edge of paper.
0214 Stationary jam in SR202, Paper was detected in the paper transport path during initial rotation, during automatic delivery, at the end
machine SR203, of cleaning, or at reception of an emergency stop command.
SR209
1118 Door open jam SR202, The door was opened when there was printing paper in the transport path.
SR203,
SR209,
SW2, SW3

3.2.2 Jam Codes (Related to Finisher)

0017-6039

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-3-3

Code Name Sensor No. Description

0130 Delayed feed jam PI5 The inlet sensor is not turned on within the specified time after reception of a paper ejection signal from
the host machine.
0231 Staying paper jam PI5 The inlet sensor is not turned off even if paper is fed by the specified distance after the leading edge of
the paper from the host machine has passed through the sensor.
0033 Stack ejection jam PI1 When a paper stack is ejected, the HP sensor is not turned off within the specified time.
0035 Staple jam Stapler HP The stapler HP sensor was turned off once after start of stapler operation, but the HP has not been reached
sensor within the specified time.
(built in
stapler)
1036 Power-on jam PI5 The inlet sensor detected paper at power-on.
1137 Door open jam SW1 The front cover switch detected opening of the front cover during standby or copy operation.

3.2.3 Jam Codes (Related to ADF)

0017-6040

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-3-4

Code Name Sensor No. Description

0000 Unknown jam - Other errors
0007 Initial stationary PI6,PI7,PI8 Paper is detected in the transport path before the DADF starts initial operation.
0008 Read sensor delay PI7,PI8 The read sensor does not detect paper when the paper has been fed by the predetermined distance
since reception of a pickup request.
0009 Read sensor stationary PI7 The trailing edge of paper is not detected when the paper has been fed by the predetermined distance
since detection of it by the read sensor.
000a Paper absence (Pull out the document.) PI11 The Document set sensor has been held off since start of pickup.
000c Delivery reversal sensor delay PI6,PI7 The delivery reversal sensor does not detect paper since the paper has been fed by the predetermined
distance since the read sensor was turned on.
000d Delivery reversal sensor stationary PI6 The trailing edge of paper is not detected when the paper has been fed by the predetermined distance
since the delivery reversal sensor detected the paper.
000e ADF cover open PI10 The feeder cover was opened during operation (of the drive system).
000f User ADF open sensor of The ADF was opened during operation (of the drive system).
the reader
unit
0010 Pickup NG - The registration sensor has been held off since paper pickup started.

3.2.4 Jam Codes (Related to Duplex Unit)

0017-6041

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

10
 Chapter 3

T-3-5

Code Name Sensor No. Description

0120 Delay jam at duplex paper sensor 1 SR1002 The duplex paper sensor 1 does not turn on within the specified time after the delivery
sensor on the main unit side turns on.
0124 Delay jam at duplex paper sensor 2 SR1003 The duplex paper sensor 2 does not turn on within the specified time after the duplex
reverse motor starts.
0221 Stationary jam at duplex paper sensor 1 SR1002 - The duplex paper sensor 1 does not turn off when the specified time has lapsed since
the duplex paper sensor 2 turned on.
- The duplex paper sensor 1 does not turn off when the paper with a longitudinal length
of 280 mm reaches the standby position (about 90 mm from the duplex paper sensor 2).
0228 Stationary jam at duplex paper sensor 2 SR1003 The duplex paper sensor 2 does not turn off when the specified time has lapsed since
the feed motor started.

3.2.5 Jam Codes (Related to Inner 2-way Tray)

0017-6042

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-3-6

Code Name Sensor No. Description

010e Delay jam at No.2 delivery section SR1101 The No.2 delivery sensor does not detect presence of paper within the specified time after turning
on of the fixing delivery sensor.
0212 Stationary jam at No.2 delivery section SR1101 Absence of paper is not detected within the specified time after turning on of the No.2 delivery
sensor.

11
 Chapter 3

12
 Chapter 4

Chapter 4 User Mode Items

4.1 User Mode Items

4.1.1 Common Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5938

iR2022i / iR2025 / iR2030 / iR2018i

T-4-1

Item Settings
Initial Function Select Initial Function: Copy*1, Send, Scan
Set System Monitor Screen as initial function: On, Off*1
Set [Device] as the default for System Monitor: On*1, Off

Auto Clear Setting Initial Function*1, Selected Function

Audible Tones Entry Tone: On *1 (1*1 to 3 levels)*2, Off
Error Tone: On *1 (1*1 to 3 levels)*2, Off
Send Done Tone: On (1 to 3 levels)*2, Off*1
Receive Done Tone: On (1 to 3 levels)*2, Off*1
Print Done Tone: On *1 (1*1 to 3 levels)*2, Off
Scan Done Tone: On *1 (1*1 to 3 levels)*2, Off

Toner Save Mode High, Low, Off*1

Printer Density 1 to 9 levels; 5*1
Inch Entry On*1, Off
Drawer Eligibility For APS/ADS Copy
Stack Bypass: On, Off*1
All Other Paper Sources: On*1, Off
Printer
Stack Bypass: cannot be set
All Other Paper Sources: On*1, Off
Receive
Stack Bypass: On, Off*1
All Other Paper Sources: On*1, Off
Other
Stack Bypass: On, Off*1
All Other Paper Sources: On*1, Off

Register Paper Type Paper Drawer 1, Paper Drawer 2*2, Paper Drawer 3*2, Paper Drawer
4*2: Plain*1, Recycled, Color, 3-hole punch, Bond, Heavy Paper 1

Energy Consumption in Sleep Mode Low*1, High

Tray Designation*2 If the Optional Inner 2 Way Tray-E2 Is Attached:

Tray A: Copy*1, Printer*1, Receive*1, Other*1
Tray B: Copy*1, Printer*1, Receive*1, Other*1
If the Optional Finisher-U2 and Additional Finisher Tray-C1 Are
Attached:
Tray A: Copy*1, Printer*1, Receive*1, Other*1
Tray B: Copy*1, Printer*1, Receive*1, Other*1

Stack Bypass Standard Settings On: Paper Size, Paper Type

Off*1
Paper Feed Method Switch Stack Bypass, Paper Drawer 1, Paper Drawer 2*2, Paper Drawer 3*2,
Paper Drawer 4*2: Speed*1, Print Side

Language Switch On, Off*1

Reversed Display (B/W) On, Off*1
Error Display for Dirty Feeder On*1, Off
Data Compress. Ratio for Remote Scans High Ratio, Normal*1, Low Ratio
Gamma Value for Remote Scans Gamma 1.0, Gamma 1.4, Gamma 1.8*1, Gamma 2.2
Initialize Common Settings Initialize: Yes, No

*1 Indicates the default setting.

*2 Indicates items that appear only when the appropriate optional equipment is attached.

4.1.2 Timer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5939

iR2022i / iR2025 / iR2030 / iR2018i

13
 Chapter 4

T-4-2

Item Settings
Date & Time Settings Date and Time Setting (12 digit number)
Time Zone Settings:
GMT -12:00 to GMT +12:00;
GMT -5:00*1
Daylight Saving Time Settings: On, Off*1

Auto Sleep Time Use Auto Sleep Time: On*1, Off

3 to 30 minutes; 5*1

Auto Clear Time 0 (Off) to 9 minutes, in one minute increments; 2 min.*1

*1 Indicates the default setting.

4.1.3 Adjustment/Cleaning (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5940

iR2022i / iR2025 / iR2030 / iR2018i

T-4-3

Item Settings
Transfer Roller Cleaning Press [Start].
Drum Cleaning Press [Start].
Fixing Unit Cleaning Cleaning Sheet Print, press [Start].
Feeder Cleaning Press [Start].
Special Mode M Standard*1, Low, Moderate, High
Special Mode N Manual (Medium, High), Off
Special Mode O Stack Bypass: Medium, High, Off*1
Drawer: Medium, High, Off*1
Special Mode P Off*1, Medium, High
Bond Special Fixing Mode On, Off*1
Special Mode S Speed Priority 1, Speed Priority 2, Off*1
Rotate Collate Adjustment Speed Priority 1*1, Speed Priority 2, Image Priority
Auto Adjustment for Dirty Feeder On*1, Off

*1 Indicates the default setting.

4.1.4 Report Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5941

iR2022i / iR2025 / iR2030 / iR2018i

T-4-4

Item Settings
Settings TX Report: On, For Error Only*1, Off
Report With TX Image: On*1, Off
Activity Report
Auto Print: On*1, Off
Send/Receive Separate: On, Off*1

RX Report: On, For Error Only, Off*1

Print List Address Book List
One-touch Buttons: Yes, No
Address Book: Yes, No

User's Data List: Yes, No

*1 Indicates the default setting.

4.1.5 System Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5942

iR2022i / iR2025 / iR2030 / iR2018i

T-4-5

Item Settings
System Manager Settings
System Manager 32 characters maximum
System Manager ID Seven digit number maximum
System Password Seven digit number maximum
Department ID Management
Department ID Management On, Off*1
Register ID/Password Register, Edit, Erase, Set page limits
Page Totals Clear, Clear All Totals, Print List
Allow ID Unknown Printer Jobs On*1, Off

14
 Chapter 4

Item Settings
Allow ID Unknown Remote Scan Jobs On*1, Off
Network Settings
Forwarding Settings
Receive Type*2 All*1, Fax, I-Fax
Validate/Invalidate On, Off*1
Register Condition Name: 50 characters maximum
Forwarding Conditions
Receive Type: Fax*2, I-Fax

Forward w/o Cond. Receive Type: Fax*2, I-Fax

Forwarding Destination: Select from the list of registered addresses.
File Format: TIFF*1, PDF, Divide into Pages

Detail/Edit Condition Name: 50 Characters maximum

Forwarding Conditions
Receive Type: Fax*2, I-Fax

Erase Yes, No
Print List Yes, No
Device Info Settings
Device Name 32 characters maximum
Location 32 characters maximum
User ID Management On, Off*1
Communications Settings
E-mail/I-Fax Settings Maximum TX Data Size: 0 to 99 MB; 3 MB*1
Divided TX over Max.Data Size: On, Off*1
Default Subject: 40 characters maximum; Attached Image*1

Fax Settings*2 Send Start Speed: 33600 bps*1, 14400 bps, 9600 bps, 7200 bps, 4800
bps, 2400 bps
Receive Start Speed: 33600 bps*1, 14400 bps, 9600 bps, 7200 bps,
4800 bps, 2400 bps

Memory Lock Settings On: Option

Off*1
Remote UI On/Off On*1 On*1, Off
Restrict the Send Function Address Book Password: 7 digits maximum
Restrict New Addresses: On, Off*1
Allow Fax Driver TX: On*1, Off
Restrict Recall: On, Off*1
Confirm Entered Fax Numbers*2: On, Off*1
Restrict Sequential Broadcast: Broadcast Confirmation, Prohibit
Broadcast, Off*1

License Registration Enter a license key using the numeric keys.

Display Dept. ID/User Name On*1, Off
Auto Online/Offline Auto Online: On, Off*1
Auto Offline: On, Off*1
Job Log Display On*1, Off
Use USB Device On*1, Off
Failed Forwarding Document Set. Print Image: On*1, Off
Store Image to Memory: On, Off*1
PDL Selection (PnP) UFRII LT*1, PCL5e, PCL6, FAX

*1 Indicates the default setting.

*2 Indicates items that appear only when the appropriate optional equipment is attached.

4.1.6 Copy Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5943

iR2022i / iR2025 / iR2030 / iR2018i

T-4-6

Item Settings
Image Orientation Priority On, Off*1
Auto Orientation On*1, Off
Standard Settings Store, Initialize
Initialize Copy Settings Yes, No

*1 Indicates the default setting.

4.1.7 Communication Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5944

iR2022i / iR2025 / iR2030 / iR2018i

15
 Chapter 4

T-4-7

Item Settings
Common Settings: TX Settings
Unit Name 24 characters maximum
Data Compression Ratio High Ratio, Normal*1, Low Ratio
Retry Times 0 to 5 times; 3 times*1
Edit Standard Send Settings Store, Initialize
TX Terminal ID On: Option (Printing Position, Telephone # Mark*2)
Gamma Value for Color Send Jobs Gamma 1.0, Gamma 1.4, Gamma 1.8*1, Gamma 2.2
Sharpness 1 to 7 levels, 4*1
Register Favorites Button M1 to M18
Color TX Scan Settings Speed Priority*1, Image Priorit
Default Screen for Send Favorite Buttons, One-touch Buttons, Initial Function*1
Initialize TX Settings Yes, No
Common Settings: RX Settings
2-Sided Print On, Off*1
Select Cassette Switch A: On*1, Off
Switch B: On*1, Off
Switch C: On*1, Off
Switch D: On*1, Off

Receive Reduction On*1 RX Reduction:

Auto*1, Fix. Red.
Reduce %: 97, 95, 90*1, 75%
Reduce Direction
Ver. Hor., Vertical Only*1
Off

Received Page Footer On, Off*1

Continue Printing When Toner Is Out On, Off*1
Fax Settings: User Settings*2
Unit Telephone # 20 characters maximum
Tel Line Type Pulse, Tone*1
Monitor Volume Control Volume Control: 0 to 3 levels, 1*1
Fax Settings: TX Settings*2
ECM TX On*1, Off
Pause Time 1 to 15 seconds; 2 seconds*1
Auto Redial On*1 Option:
Redial Times: 1 to 10 times; 2 times*1
Redial Interval: 2 to 99 minutes; 2*1
minutes*1
TX Error Redial: On*1, Off
Off

Check Dial Tone Before Sending On*1, Off

Rotate Send On*1, Off
Fax Setting: RX Settings*2
ECM RX On*1, Off

*1 Indicates the default setting.

*2 Indicates items that appear only when the appropriate optional equipment is attached.

4.1.8 Printer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5945

iR2022i / iR2025 / iR2030 / iR2018i

T-4-8

Item Settings
DEFAULT PAPERSIZE LTR*, STMT, EXECUTIV, ISO-B5, ISO-C5, COM10,
MONARCH, DL, A4, A3, B4, B5, A5, 11X17, LGL
DEFAULT PAPERTYPE PLAIN PAPER*, COLOR, RECYCLED, HEAVY PAPER 1,
HEAVY PAPER 2, HEAVY PAPER 3, BOND, 3-HOLE PUNCH
PAPER, TRANSPARENCY, LABELS, ENVELOPE

COPIES 1 to 999; 1*
2-SIDED PRINTING OFF*, ON
PRINT QUALITY
IMAGE REFINEMENT ON*, OFF
DENSITY 9 levels; 5*
TONER SAVER OFF*, ON
PAGE LAYOUT
BINDING LONG EDGE*, SHORT EDG

16
 Chapter 4

Item Settings
MARGIN INCHES*: -01.90 INCHES to 01.90 INCHES; 00.00 INCHES*
MM: -50.0 MM to 50.0 MM; 0.0 MM*
AUTO ERROR SKIP OFF*, ON
ERROR TIME OUT ON* (TIME OUT PERIOD: 5 to 300 SEC), OFF; 15 SEC*
COLLATE OFF*, COLLATE, ROTATE + COLLATE*1, ROTATE +
GROUP*1, OFFSET + COLLATE*2, OFFSET + GROUP*2,
STAPLE*2 (STAPLE POSITION: TOP LEFT*, TOP RIGHT,
BOTTOM LEFT)

INIT. PRINTER SET OFF*, ON

RESET PRINTER OFF*, ON
PCL Settings
PAPER SAVE OFF*, ON
ORIENTATION PORTRAIT*, LANDSCAPE
FONT NUMBER 0 to 89; 0*
POINT SIZE 4.00 to 999.75 point; 12.00 point*
PITCH 0.44 to 99.99 cpi; 10.00 cpi*
FORM LINES 5 to 128 lines; 60 lines*
SYMBOL SET PC8*, PC850, PC852, PC858, PC8DN, PC8TK, PC1004, PSTEXT,
ROMAN8, ROMAN9, WIN30, WINBALT, WINL1, WINL2,
WINL5, DESKTOP, ISO4, ISO6, ISO11, ISO15, ISO17, ISO21,
ISO60, ISO69, ISOL1, ISOL2, ISOL5, ISOL6, ISOL9, LEGAL,
MCTEXT, PC775

CUSTOM PAPER OFF*, ON

UNIT OF MEASURE INCHES*, MILLIMETERS
X DIMENSION 5.83" to 17.00" (148 mm to 432 mm); 17.00"* (432 mm)
Y DIMENSION 3.75" to 11.69" (95 mm to 297 mm); 11.69"* (297 mm)
APPEND CR TO LF NO*, YES
ENLARGE A4 OFF*, ON
HALFTONE
TEXT TONE, GRADATION, RESOLUTION*
GRAPHICS TONE*, GRADATION, RESOLUTION
IMAGE TONE*, GRADATION, RESOLUTION
BarDIMM*3 ENABLE*, DISABLE
FreeScape ~*, ", #, $, /, \, ?, {, }, |, OFF

An asterisk(*) indicates the default settings.

*1 Rotate items do not appear when the optional Finisher-U2 is attached.
*2 Offset and staple items appear only when the optional Finisher-U2 is attached.
*3 This setting is available only if the BarDIMM function is activated.

4.1.9 Address Book Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)

0017-5946

iR2022i / iR2025 / iR2030 / iR2018i

T-4-9

Item Settings
Register Address: Register New Address
Fax*2 Fax Number: 120 characters maximum
Option: Sending Speed, Long Distance, ECM TX
Register Name: 16 characters maximum

E-mail E-mail Address: 120 characters maximum

Register Name: 16 characters maximum
I-Fax I-Fax Address: 120 characters maximum
Register Name: 16 characters maximum
File Protocol: FTP*1, Windows (SMB)
Host Name: 120 characters maximum
File Path: 120 characters maximum
User: 24 characters maximum
Password: 24 characters maximum (FTP),
14 characters maximum (Windows (SMB))
Register Name: 16 characters maximum

Group Address Book

Erase
Register Name: 16 characters maximum

Register Address: Erase

Register Address: Edit
One-touch Buttons
Register/Edit You can register or edit the items of One-touch Buttons for Fax, E-
mail, I-Fax,
File, and Group shown in Register New Add above.
Key Name: 12 characters maximum

17
 Chapter 4

*1 Indicates the default setting.

*2 Indicates items that appear only when the appropriate optional equipment is attached.

4.1.10 Recommended setting of system management information

0017-5948

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

When multiple users use the machine, it is necessary to advise each user to set the system management information.
Setting ID and password of system administrator on the operation unit under (Additional functions key) > [System management setting] > [Setting of system ad-
ministrator's information] has an effect of restraining the third person from falsifying information, for the ID and password are required when a user carries out an
important setting of the machine.
Under the environment that the setting is not done, if a user who does not sufficiently know operation situation of the machine tries to change the setting, following
troubles may occur.
- When the user changes [User ID Management] from [off] to [on], copying operation cannot be done unless ID and password are input.
- When each setting is changed on the network from RUI, that enables to falsify data of address book or delete log.
- When TCP/IP fixed address is changed on the network setting, printing operation via network cannot be done until the port setting is changed.
- When usage restriction of USB device is changed to [on], printing operation via USB becomes disabled.

4.1.11 The Reference Information of the Department ID Management

0017-5949

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Function:
If Department is registered in Department ID Management, users are required to input the Department ID and password when inputting data from the operation
unit of the machine. Also, the registration enables to restrict usage and control the usage number of times of Total Parts, Copy, B&W Scan, Color Scan, or Print.
Setting method:
Register Department ID in Department ID Management under Additional Functions key>System Setting.
Operation outline:
Department ID can be registered in [Department ID management] from the operation unit of the machine even though [System Manager Settings] is not done.
When registering data in [Department ID Management] using RUI, you need to register yourself as a system manager in [System Manager Settings] and login
as a system manager.

18
 Chapter 5

Chapter 5 Service Mode

5.1 Fax System Service Mode

5.1.1 Service Soft Switch Settings (SSSW)

5.1.1.1 Outline
5.1.1.1.1 Bit Switch Composition
0017-6052
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The items registered and set by each of these switches comprise 8-bit switches. The figure below shows which numbers are assigned to which bits. Each bit has a
value of either 0 or 1.

t2
t1
t7
t6
t5
t4
t3

t0
Bi
Bi
Bi
Bi
Bi
Bi
Bi

Bi
#SSSW
001 0 0 0 0 0 0 0 0

F-5-1

Do not change service data identified as "not used"; they are set as initial settings.

5.1.1.2 SSSW-SW01
5.1.1.2.1 List of Functions
0017-6053
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-1

Bit Function 1 0

0 service error code output not output

1 not used - -

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 not used - -

5.1.1.2.2 Detailed Discussions of Bit 0

0017-6054
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Selects whether or not service error codes are output.

When output is selected, service error codes is report.
5.1.1.3 SSSW-SW03
5.1.1.3.1 List of Functions
0017-6055
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-2

Bit Function 1 0

0 not used - -

1 not used - -

19
 Chapter 5

Bit Function 1 0

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 tonal signal before CED signal transmission transmit do not transmit

5.1.1.3.2 Detailed Discussions of Bit 7

0017-6056
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to enable/disable transmission of a 1080-Hz tonal signal before transmission of the CED signal.
Select 'transmit' if errors occur frequently because of an echo when reception is from overseas.

Memo:
Any of the following error code may be indicated because of an echo at time of reception
##0005, ##0101, ##0106, ##0107, ##0114, ##0200, ##0201, ##0790

5.1.1.4 SSSW-SW04
5.1.1.4.1 List of Functions
0017-6057
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-3

Bit Function 1 0

0 not used - -

1 not used - -

2 the number of final flag sequences of protocol signals 2 1

3 Reception mode after CFR signal transmission high speed high speed/low speed

4 the length of the period of ignoring low speed signals after 1500 ms 700 ms
CFR output
5 CI signal frequency check at the time of PBI setting Check Not

6 CNG signal for manual transmission Not transmitted Transmitted

7 CED signal for manual reception Not transmitted Transmitted

5.1.1.4.2 Detailed Discussions of Bit 2

0017-6058
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to select the number of last flag sequences for a protocol signal (transmission speed at 300 bps). Select '2' if the other party fails to receive the protocol signal
properly.

Memo:
Any of the following error codes may be indicated at time of transmission
##0100, ##0280, ##0281, ##0750, ##0753, ##0754, ##0755, ##0758, ##0759, ##0760, ##0763 ##0764, ##0765, ##0768, ##0769,##0770, ##0773, ##0775, ##0778,
##0780, ##0783, ##0785, ##0788

5.1.1.4.3 Detailed Discussions of Bit 3

0017-6059
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to select an appropriate reception mode after transmission of the CFR signal.
If errors occur frequently at time of reception because of the condition of the line, select 'high speed' for reception mode and, at the same time, selects 'do not receive'
for 'ECM reception.'

Memo:
Any of the following error codes may be indicated at time of reception because of line condition
##0107, ##0114, ##0201
Be sure to change bit 4 before changing this bit; if errors still occur, change this bit.
When 'high speed' is selected, only high-speed signals (images) will be received after transmission of the CFR signal.

20
 Chapter 5

5.1.1.4.4 Detailed Discussions of Bit 4

0017-6060
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal.
If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.'
5.1.1.4.5 Detailed Discussions of Bit 5
0017-8523
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

In the countries that need approval of CI signal frequency check, no checking on frequency set at PBX when changing the frequency to PSTN setting and PBX
setting for frequency checks.
5.1.1.4.6 Detailed Discussions of Bit 6
0017-6063
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Selects whether or not to transmit CNG signal during manual transmission.

In manual transmitting to a fax with the FAX/TEL switching mode, if there are frequent errors due to failure to switch to fax mode, select "Transmitted" for the
CNG signal.
5.1.1.4.7 Detailed Discussions of Bit 7
0017-6064
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Selects whether or not to transmit CED signals during manual reception. If the other fax does not transmit even when you start manual reception, select "Transmit-
ted" for the CED signal.
5.1.1.5 SSSW-SW05
5.1.1.5.1 List of Functions
0017-6065
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-4

Bit Function 1 0

0 not used - -

1 Conversion from mm to inch (text mode) convert do not convert

2 Conversion from mm to inch (text/photo mode) convert do not convert

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 not used - -

5.1.1.5.2 Detailed Discussions of Bit 1

0017-6066
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode.
Scanning direction in conversion follows the Bit 2 setting of SW14.
5.1.1.5.3 Detailed Discussions of Bit 2
0017-6067
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text/photo mode while bit 1 is set to '1'.
Scanning direction in conversion follows the Bit 2 setting of SW14.
5.1.1.6 SSSW-SW12
5.1.1.6.1 List of Functions
0017-6068
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

21
 Chapter 5

T-5-5

Bit Function 1 0

0 Time-out period for one page upon transmission 1 0

1 Time-out period for one page upon transmission 1 0

2 not used - -

3 not used - -

4 Time-out period for one page upon reception 1 0

5 Time-out period for one page upon reception 1 0

6 not used - -

7 Respective page timer settings for transmission and for enable do not enable
reception

The machine will stop the ongoing communication if the transmission/reception of a single original page takes 32 min or more. To use the timer for a purpose other
than this function, refer to the tables that follow, and select an appropriate time length.
When 'do not enable' is selected using bit 7, the time-out length for a single page for all modes will depend on the setting of bit 0 and bit 1.

T-5-6

Time-Out Length for Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Transmission/Reception
8 min 0 * * * * * 0 0

16 min 0 * * * * * 0 1

32 min 0 * * * * * 1 0

64 min 0 * * * * * 1 1

T-5-7

Time-Out Length for Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Transmission (in text
mode)
8 min 1 * * * * * 0 0

16 min 1 * * * * * 0 1

32 min 1 * * * * * 1 0

64 min 1 * * * * * 1 1

T-5-8

Time-Out Length for Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Reception
8 min 1 * 0 0 * * * *

16 min 1 * 0 1 * * * *

32 min 1 * 1 0 * * * *

64 min 1 * 1 1 * * * *

5.1.1.7 SSSW-SW13
5.1.1.7.1 List of Functions
0017-6069
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-9

Bit Function 1 0

0 not used - -

22
 Chapter 5

Bit Function 1 0

1 not used - -

2 Convert "inch" into "mm" when transmitting the received convert do not convert
image data
3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 not used - -

5.1.1.7.2 Detailed Discussions of Bit 2

0017-6070
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

It converts "inch" into "mm" when transmitting the received image data.
Scanning direction in conversion follows the Bit 2 setting of SW14.
5.1.1.8 SSSW-SW14
5.1.1.8.1 List of Functions
0017-6071
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-10

Bit Function 1 0

0 not used - -

1 not used - -

2 direction of scanning for inch/mm conversion both main and sub sub scanning
scanning directions direction only
3 not used - -

4 inch-configuration resolution declaration declare do not declare

5 not used - -

6 not used - -

7 not used - -

5.1.1.8.2 Detailed Discussions of Bit 2

0017-6072
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to specify whether to convert or not convert an inch-configuration resolution into a millimeter-configuration resolution for image read in G3 transmission:
either in sub scanning direction only or in both main and sub scanning directions. The setting is valid only when bit 1 of SW05 of #SSSW is set to '1'.
5.1.1.8.3 Detailed Discussions of Bit 4
0017-6073
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to specify whether to declare or not declare an inch-configuration resolution to the other machine for G3 communication: if 'declare' is selected, the machine
will indicate that it reads and records at an inch-configuration resolution using the DIS, DCS, or DTC signal.
5.1.1.9 SSSW-SW25
5.1.1.9.1 List of Functions
0017-8526
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-11

Bit Function 1 0

0 procedure of V.8 on the initiation side receiver's number initial call number

1 not used - -

23
 Chapter 5

Bit Function 1 0

2 If void CSI has been received, handle as non-received Yes No

CSI.
3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 not used - -

5.1.1.9.2 Detailed Discussions of Bit 0

0017-8528
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Transmitted telephone number could be selected on the report indication after the transmission.
If the "Initiation number" is selected, report will indicate the telephone number of the initiation side.
If the "Receiver's number" is selected, report will indicate the phone number (CSI signal data) which is sent by the receiver's side.
5.1.1.9.3 Detailed Discussions of Bit 2
0017-8529
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

At "1" on this Bit, ignore the void CSI if received and if the dial has been made at this point, the dialed number will be indicated on the LCD/ Report screen.
At "0" on this Bit, even though the dialed number is acknowledged, LCD/Report screen will indicate nothing.
5.1.1.10 SSSW-SW28
5.1.1.10.1 List of Functions
0017-6074
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-12

Bit Function 1 0

0 Caller V.8 protocol NO YES

1 Called party V.8 protocol NO YES

2 Caller V.8 protocol late start NO YES

3 Called party V.8 protocol late start NO YES

4 V.34 reception fallback Prohibited Not prohibited

5 V.34 transmission fallback Prohibited Not prohibited

6 not used - -

7 not used - -

5.1.1.10.2 Detailed Discussions of Bit 0

0017-6075
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Select whether to use the V.8 protocol when calling. If NO is selected, the V.8 protocol is inhibited at calling and the V.21 protocol is used.
5.1.1.10.3 Detailed Discussions of Bit 1
0017-6076
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Select whether to use the V.8 protocol when called. If NO is selected, the V8 protocol is inhibited when called and the V.21 protocol is used.
5.1.1.10.4 Detailed Discussions of Bit 2
0017-6077
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
If ANSam signal is not received during transmission, select whether to use the V.8 protocol when the other fax machine declares the V.8 protocol in DIS signal. If
NO is selected, the CI signal is not transmitted and the V.8 protocol is not used even if the DIS that specifies the V.8 protocol is received.
The V.8 late start is not executed during manual transmission regardless of this setting.
5.1.1.10.5 Detailed Discussions of Bit 3
0017-6078
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

24
 Chapter 5

Select whether to declare the V.8 protocol in DIS signal for reception. If NO is selected, the V.8 protocol cannot be used because it is not declared in DIS signal.
The V.8 late start is not executed during manual reception regardless of this setting.
5.1.1.10.6 Detailed Discussions of Bit 4
0017-6079
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether the receiver falls back during V.34 reception. If 'Prohibit' is selected, the receiver does not fall back.
5.1.1.10.7 Detailed Discussions of Bit 5
0017-6080
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether the transmitter falls beck during V.34 transmission. If 'Prohibit' is selected, teh transmitter does not fall back.
5.1.1.11 SSSW-SW30
5.1.1.11.1 List of Functions
0017-6081
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-13

Bit Function 1 0

0 Not used - -

1 Not used - -

2 Not used - -

3 Not used - -

4 Not used - -

5 New dial tone detection method Detect with the new Detect with the
method. existing method.
6 Not used - -

7 Not used - -

5.1.1.11.2 Detailed Discussions of Bit 5

0017-6082
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
When "Detect with the new method" is selected, tone is detected for 3.5 seconds before call origination in order to discriminate between dial tone and voice. If dial
tone is detected and the time since line seizure is 3.5 seconds or longer, call origination takes place immediately. If the time since line seizure is less than 3.5 seconds,
call origination takes place after waiting for 1 second. (If the time since line seizure reaches 3.5 seconds during the 1-second waiting period, call origination takes
place immediately. By default, "Detect with a new method" is assigned for this SW.
5.1.1.12 SSSW-SW33
5.1.1.12.1 List of Functions
0017-6083
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-14

Bit Function 1 0

0 count B4 (Print) as large size Yes No

1 indicate serial No. on counter check screen Yes No

2 count B4 (Scan) as large size Yes No

3 the counter display type change in Japan and USA Yes No

4 Yes No

5 not used - -

6 not used - -

7 not used - -

25
 Chapter 5

5.1.1.12.2 Detailed Discussions of Bit 0

0017-6084
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to specify whether B4 paper (Print) should be counted as large-size paper.

If 'yes' is selected, B4 paper will be counted as large-size paper.
If 'no' is selected, on the other hand, B4 paper will be counted as small-size paper.
5.1.1.12.3 Detailed Discussions of Bit 1
0017-6085
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to specific whether to indicate the machine serial No. on the Counter Check screen, appearing when the Counter key is pressed.
If 'yes' is selected, the serial No. will be indicated.
If 'no' is selected, on the other hand, the serial No. will not be indicated.
5.1.1.12.4 Detailed Discussions of Bit 2
0017-6086
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to specify whether B4 paper (Scan) should be counted as large-size paper.

If 'yes' is selected, B4 paper will be counted as large-size paper.
If 'no' is selected, on the other hand, B4 paper will be counted as small-size paper.
5.1.1.12.5 Detailed Discussions of Bit 3 - Bit4
0017-6087
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to switch the counter display type in effect in Japan and USA to the conventional or new type. Select "Yes" to display counters in the new type.
Select "No" to display counters in the conventional type.
T-5-15

Bit4 Bit3

Conventional type 0 0

New type 1 0 1

New type 2 1 0

5.1.1.13 SSSW-SW34
5.1.1.13.1 List of Functions
0017-6088
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-16

Bit Function 1 0

0 Display the waste toner full YES NO

warning

1 Switch the waste toner full Drum replacement required E019 displayed on an service
warning message displayed on an call
operator call
2 Not used - -

3 Not used - -

4 Not used - -

5 Not used - -

6 Not used - -

7 Not used - -

The default setting of this SSSW varies depending on the destination of the product.
Product for Japan: 00000000
Product for countries in Euro zone: 00000011
Products for other countries/regions: 00000001
5.1.1.13.2 Detailed Discussions of Bit 0
0017-6089
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

26
 Chapter 5

You can select whether a waste toner full warning is to be displayed.

When "1" is selected, a waste toner full warning is displayed.
When "0" is selected, a waste toner full warning is not displayed.
5.1.1.13.3 Detailed Discussions of Bit 1
0017-6090
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to display the waste toner full warning as a drum replacement required message or as E019 displayed on an operator call. Select 1 to display a rum
replacement required message on an operator call. Select 0 to display E019 on an service call.

5.1.2 Menu Switch Settings (MENU)

5.1.2.1 Menu Switch Composition

0017-6092

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-17

No. Function Range of settings

005 NL equalizer 1: ON, 0: OFF
006 telephone line monitor 0:DIAL, 1:SERVICEMAN1, 2:SERVICEMAN2, 3:OFF
007 transmission level (ATT) from 0 to 15 (ex: 15= -15 dBm)
008 V.34 modulation speed upper 0:3429, 1:3200, 2:3000, 3:2800, 4:2743, 5:2400
limit
009 V34 data speed upper limit 0:33.6 kbps, 1:31.2 kbps, 2:28.8 kbps, 3:26.4 kbps, 4:24.0 kbps,
5:21.6 kbps, 6:19.2 kbps, 7:16.8 kbps, 8:14.4 kbps, 9:12.0 kbps,
10:9.6 kbps, 11:7.2 kbps, 12:4.8 kbps, 13:2.4 kbps
010 Frequency of pseudoring signal 0:50 Hz, 1:25 Hz, 2:17 Hz

5.1.2.2 <No.005 NL equalizer>

0017-6093

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to enable-disable the NL equalizer.

If errors occur often during communication because of the condition of the line, enable (ON) the NL equalizer.

Any of the following error codes may be indicated at time of transmission because of the line condition:
##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765, ##774, ##779, ##784, ##789
Any of the following error codes may be indicated at time of transmission because of the line condition:
##103, ##107, ##114, ##201, ##790, ##793

5.1.2.3 <No.006 telephone line monitor>

0017-6094

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to s the telephone line monitor function:

DIAL: generate the monitor sound of the telephone line using the speaker from the start of transmission to DIS.
SERVICEMAN [1]: generate the monitor sound of the telephone line using the speaker from the start of communication to the end of it.
SERVICEMAN [2]: generate the monitor sound of the telephone line2 (Option).
OFF: do not generate the monitor sound of the telephone line using the speaker.

5.1.2.4 <No.007 ATT transmission level>

0017-6095

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the transmission level (ATT).

Raise the transmission level if errors occur frequently at time of communication because of the condition of the line. (It means close to 8)

Any of the following error codes may be indicated at time of transmission because of the line condition:
##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750, ##752, ##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765,
##767, ##769, ##770, ##772, ##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787, ##789
Any of the following error codes may be indicated at time of reception because of the line condition:
##103, ##106, ##107, ##201, ##793

5.1.2.5 <No.008 V.34 modulation speed upper limit>

0017-6096

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel.

5.1.2.6 <No.009 V.34 data speed upper limit>

0017-6097

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set an upper limit to the data transmission speed for the V.34 primary channel between 2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13:
33.6K bps).

5.1.2.7 <No.010 Frequency of the pseudo CI signal>

0017-6098

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

You may select a frequency for the pseudo CI signal.

Some types of external telephones do not ring when the fax/tel switch-over function is ON. To sound the ring, change the pseudo CI signal.

27
 Chapter 5

5.1.3 Numeric Parameter Settings (NUMERIC Param.)

5.1.3.1 Numerical Parameter Composition

0017-6099

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-18

No. Item Range of settings

002 RTN transmission condition(1) 1% to 99%
003 RTN transmission condition (2) 2 to 99 item
004 RTN transmission condition (3) 1 to 99 lines
005 NCC pause time length (pre-ID code) 1 to 60 sec
006 NCC pause time length (post-ID code) 1 to 60 sec
010 line condition identification time length 0 to 9999 (10 msec)
011 T.30T1 timer (for reception) 0 to 9999 (10 msec)
013 T.30 EOL timer 500 to 3000 (10 msec)
015 hooking detection time length 0 to 999
016 time length to first response at time of fax/tel switchover 0 to 9
017 pseudo RBT signal pattern ON time length 0 to 999
018 pseudo RBT signal pattern OFF time length 0 to 999
(short)
019 pseudo RBT signal pattern OFF time length 0 to 999
(long)
020 pseudo CI signal pattern ON time length 0 to 999
021 pseudo CI signal pattern OFF time length 0 to 999
(short)
022 pseudo CI signal pattern OFF time length (long) 0 to 999
023 CNG detection level at time of fax/tel switchover 0 to 7
024 pseudo RBT transmission level at time of fax/tel switchover 10 to 20
0 to 20 (120/230V)
025 Answering machine connection function signal detection 0 to 999
time
027 preamble detection time length for V21 low-speed flag 20 (x 10ms)
055 acquisition period of environmental log data 0 to 480 (60min)
056 display the type of soft counter 1 101 (Fixed)
057 Display the type of soft counter 2 0 to 999
058 Display the type of soft counter 3 0 to 999
059 Display the type of soft counter 4 0 to 999
060 Display the type of soft counter 5 0 to 999
061 Display the type of soft counter 6 0 to 999

5.1.3.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition
(3)>
0017-6100

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set RTN signal transmission conditions. Raise these parameters for more lenient conditions if errors occur frequently at time of reception because of trans-
mission of the RTN signal.

Memo:
Any of the following error codes may be indicated at time of reception because of RTN signal transmission
##0104, ##0107, ##0114, ##0201

RTN signal transmission condition (1) affects the ratio of error lines to the total number of lines per single page of received images.
RTN signal transmission condition (2) affects the standard value (*2) of burst errors (*1).
RTN signal condition (3) affects the number of errors not reaching the standard value of burst errors.

*1: transmission error occurring cover several lines.

*2: for instance, if '15' is set, a single burst error will represent an error occurring continuously cover 15 lines.

If any of these lines is detected while an image signal is being received, the RTN signal will be transmitted after receiving the protocol signal of the transmitting
party. Higher parameters restrict the transmission of the RTN signal.

5.1.3.3 <005: NCC pause length (pre-ID code)>

0017-6102

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the length of the pause automatically entered between access code and ID code when the NCC (New Common Carrier) line is used for dialing.

5.1.3.4 <006: NCC pause length (post-ID code)>

0017-6103

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the length of the pause automatically entered between ID code and telephone number of the other party when the NCC (New Common Carrier) line is
used for dialing.

28
 Chapter 5

5.1.3.5 <010: line connection identification length>

0017-6104

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the time for identifying the line connection. Raise this parameter if errors occur frequently at time of communication because of the condition of the line.

Memo:
Any of the following error codes may be indicated because of the condition of the line
##0005, ##0018
The line condition identification time is between when the dial signal is transmitted and when the line condition is cut for the transmitting party, while it is between
when the DIS signal is transmitted and when the line is cut for the receiving party.

5.1.3.6 <011: T.30 T1 timer (for reception)>

0017-6105

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set the T1 timer for the receiver (wait time after DIS transmission starts until a significant signal is received).

5.1.3.7 <013: T.30 EOL timer>

0017-6106

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set it so that the 1-line transmission time is longer for reception to prevent reception errors caused by a long data length per line (e.g., computer FAX).

5.1.3.8 <016: time length to first response at time of fax/tel switchover>

0017-6108

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Allows setting of the time from seizing the line till pseudo RBT is sent, when the Fax/ Tel switching function is operating.

5.1.3.9 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:
pseudo RBT signal pattern OFF time length (long)>
0017-6109

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the pattern of the pseudo RBT signal transmitted at time of a fax/tel switchover.

5.1.3.10 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)>
0017-6110

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the pseudo CI signal pattern transmitted at time of a fax/tel switchover.

5.1.3.11 <023: CNG detention level for fax/tel switchover>

0017-6111

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the CNG detention level for a fax/tel switchover.

5.1.3.12 <024: pseudo RBT transmission level at time of fax/tel switchover>

0017-6112

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the pseudo transmission level for a fax/tel switchover.

5.1.3.13 <025: Answering machine connection function signal detection time>

0017-6113

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Sets the signal detection time for the answering machine connection function operation. When the answering machine connection function is operating, if the func-
tion does not operate normally because the fax does not detect CNG signal sent from the line, raise this parameter to increase the signal detection time.

5.1.3.14 <027: V.21 low-speed flag preamble identification length>

0017-6114

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to detect the time of detection after which command analysis is started after detecting V.21 low-speed command preambles continuously for a specific period
of time.

5.1.3.15 <055: Acquisition period of environmental log data>

0017-8531

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to change the acquisition period of environmental log data.

5.1.3.16 <056 - 061: Count type select >

0017-6115

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to confirm the count type indicated on the Counter Check screen, which appears in response to a press on the Counter key.
When '0' is selected, count type will not be indicated.
No.56: Use it to indicate the type of software counter 1 of the control panel. The type of soft counter 1 cannot be changed.
No.57: Use it to change the type of soft counter 2* of the control panel to suit the needs of the user.
No.58: Use it to change the type of soft counter 3* of the control panel to suit the needs of the user.
No.59: Use it to change the type of soft counter 4* of the control panel to suit the needs of the user.
No.60: Use it to change the type of soft counter 5* of the control panel to suit the needs of the user.
No.61: Use it to change the type of soft counter 6* of the control panel to suit the needs of the user.
*:The default type settings of soft counter is different from models.
<Soft Counter Specifications>
The soft counters are classified a follows in terms of input numbers:
100s: total

29
 Chapter 5

200s: copy
300s: print
400s: copy + print
500s: scan
700s: received file print
800s: report pint
900s: transmitted scan

Guide to the Table

- 1:Count sheets of all sizes by one.
- 2:Count sheets of the large size by two.
- C:full color
- Bk:black mono
- L:large size (larger than A4/LTR)
- S:small size (A4/LTR or smaller)

MEMO:
To make a change so that B4 papers (for print) will be counted as large-size, use service mode: make the following selections, and change bit 0 to '1': #SSSW>SW33.
To make a change so that B4 papers (for scan) will be counted as large-size, use service mode: make the following selections, and change bit 2 to '1': #SSSW>SW33.

Seri Counter type Print system

al Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S
No.
on
Local PDL FAX Repo Local PDL FAX Repo Local PDL FAX Repo Local PDL FAX Repo
coun
copy print print rt copy print print rt copy print print rt copy print print rt
ter
print print print print
chec
k
scree
n
101 Total1 1 1 1 1 1 1 1 1
102 Total2 2 2 2 2 1 1 1 1
103 Total (L) 1 1 1 1
104 Total (S) 1 1 1 1
108 Total (Bk1) 1 1 1 1 1 1 1 1
109 Total (Bk2) 2 2 2 2 1 1 1 1
112 Total (Bk/L) 1 1 1 1
113 Total (Bk/S) 1 1 1 1
114 Total1 (2-sided) 1 1 1 1 1 1 1 1
115 Total2 (2-sided) 2 2 2 2 1 1 1 1
116 L (2-sided) 1 1 1 1
117 S (2-sided) 1 1 1 1
126 TotalA1 1 1 1 1 1 1
127 TotalA2 2 2 2 1 1 1
128 TotalA (L) 1 1 1
129 TotalA (S) 1 1 1
132 TotalA (Bk1) 1 1 1 1 1 1
133 TotalA (Bk2) 2 2 2 1 1 1
136 TotalA (Bk/L) 1 1 1
137 TotalA (Bk/S) 1 1 1
138 TotalA1 (2-sided) 1 1 1 1 1 1
139 TotalA2 (2-sided) 2 2 2 1 1 1
140 L A (2-sided) 1 1 1
141 S A (2-sided) 1 1 1
150 TotalB1 1 1 1 1 1 1
151 TotalB2 2 2 2 1 1 1
152 TotalB (L) 1 1 1
153 TotalB (S) 1 1 1
156 TotalB (Bk1) 1 1 1 1 1 1
157 TotalB (Bk2) 2 2 2 1 1 1
160 TotalB (Bk/L) 1 1 1
161 TotalB (Bk/S) 1 1 1
162 TotalB1 (2-sided) 1 1 1 1 1 1
163 TotalB2 (2-sided) 2 2 2 1 1 1
164 LB (2-sided) 1 1 1
165 SB (2-sided) 1 1 1
201 Copy(Total1) 1 1
202 Copy(Total2) 2 1
203 Copy(L) 1
204 Copy(S) 1
205 CopyA (Total1) 1 1
206 CopyA (Total2) 2 1
207 CopyA (L) 1
208 CopyA (S) 1

30
 Chapter 5

Seri Counter type Print system

al Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S
No.
on
Local PDL FAX Repo Local PDL FAX Repo Local PDL FAX Repo Local PDL FAX Repo
coun
copy print print rt copy print print rt copy print print rt copy print print rt
ter
print print print print
chec
k
scree
n
209 Local copy(Total1) 1 1
210 Local copy(Total2) 2 1
211 Local copy(L) 1
212 Local copy(S) 1
221 Copy(Bk1) 1 1
222 Copy(Bk2) 2 1
227 Copy(Bk/L) 1
228 Copy(Bk/S) 1
237 Copy(Bk/L/2-sided) 1
238 Copy(Bk/S/2-sided) 1
249 CopyA (Bk1) 1 1
250 CopyA (Bk2) 2 1
255 CopyA (Bk/L) 1
256 CopyA (Bk/S) 1
265 CopyA (Bk/L/2-sided) 1
266 CopyA (Bk/S/2-sided) 1
277 Local copy(Bk1) 1 1
278 Local copy(Bk2) 2 1
283 Local copy(Bk/L) 1
284 Local copy(Bk/S) 1
293 Local copy(Bk/L/2-sided) 1
294 Local copy(Bk/S/2-sided) 1
301 Print (Total1) 1 1 1 1
302 Print (Total2) 2 2 1 1
303 Print (L) 1 1
304 Print (S) 1 1
305 PrintA (Total1) 1 1 1 1
306 PrintA (Total2) 2 2 1 1
307 PrintA (L) 1 1
308 PrintA (S) 1 1
313 Print (Bk1) 1 1 1 1
314 Print (Bk2) 2 2 1 1
319 Print (Bk/L) 1 1
320 Print (Bk/S) 1 1
329 Print (Bk/L 1 1
330 Print (Bk/S/2-sided) 1 1
331 PDL print (Total1) 1 1
332 PDL print (Total2) 2 1
333 PDL print (L) 1
334 PDL print (S) 1
339 PDL print (Bk1) 1 1
340 PDL print (Bk2) 2 1
345 PDL print (Bk/L) 1
346 PDL print (Bk/S) 1
355 PDL print (Bk/L/2-sided) 1
356 PDL print (Bk/S) 1
403 Copy+Print (Bk/L) 1 1 1
404 Copy+Print (Bk/S) 1 1 1
405 Copy+Print (Bk2) 2 2 2 1 1 1
406 Copy+Print (Bk1) 1 1 1 1 1 1
411 Copy+Print (L) 1 1 1
412 Copy+Print (S) 1 1 1
413 Copy+Print (2) 2 2 2 1 1 1
414 Copy+Print (1) 1 1 1 1 1 1
421 Copy+Print (Bk/L) 1 1 1
422 Copy+Print (Bk/S) 1 1 1
701 Recieved print (Total1)
702 Recieved print (Total2)
703 Recieved print (L)

31
 Chapter 5

Seri Counter type Print system

al Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S
No.
on
Local PDL FAX Repo Local PDL FAX Repo Local PDL FAX Repo Local PDL FAX Repo
coun
copy print print rt copy print print rt copy print print rt copy print print rt
ter
print print print print
chec
k
scree
n
704 Recieved print (S)
709 Recieved print (Bk1)
710 Recieved print (Bk2)
715 Recieved print (Bk/L)
716 Recieved print (Bk/S)
725 Recieved print (Bk/L/2- 1
sided)
726 Recieved print (Bk/S/2- 1
sided)
801 Report print (Total1)
802 Report print (Total2)
803 Report print (L)
804 Report print (S)
809 Report print (Bk1)
810 Report print (Bk2)
815 Report print (Bk/L)
816 Report print (Bk/S)
825 Report print (Bk/L) 1
826 Report print (Bk/S) 1

Serial Counter type Scan system

No. on
Bk 1-sided L Bk 1- C 1-sided L C 1-
counte
sided sided
r check
S S
screen

Total Pull E- FileS E- FileS E- Total Total Pull E- FileS E- E- Total

scan scan mail hare mail hare mail scan scan scan mail hare mail FileS mail scan
scan DBsc FileS DB FileS scan DB FileS hare FileS
an hare BoxF hare scan hare DB hare
DB scan DB DB scan DB
scan Box scan BOX
scan
501 Scan (Total1) 1 1
505 Bk scan (Total1) 1 1
506 Bk scan (Total2) 2 1
507 Bk scan (L) 1
508 Bk scan (S) 1
509 C scanTotal (1) 1 1
510 C scanTotal (2) 2 1
511 C scan (L) 1
512 C scan (S) 1
915 Transmission scan total2 1
(C)
916 Transmission scan total2 1
(Bk)
917 Transmission scan total3 1
(C)
918 Transmission scanTotal3 1
(Bk)
921 Transmission scanTotal5 1
(C)
922 Transmission scanTotal5 1
(Bk)
929 Transmission scanTotal6 1
(C)
930 Transmission scanTotal6 1
(Bk)
939 Remote scan (C) 1
940 Remote scan (Bk) 1
945 Transmission scan/E-mail
(C)
946 Transmission scan/E-mail 1
(Bk)

32
 Chapter 5

5.1.4 Scanner Function Settings (SCANNER)

5.1.4.1 Setting of Bit Switch

0017-6116

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

<SCAN SW SSSW01>
T-5-19

Bit Function 1 0

0 Not used - -

1 Not used - -

2 Not used - -

3 Not used - -

4 Outputting an Image for ADF Perpendicularity output not output

Adjsutment
5 Not used - -

6 Not used - -

7 Not used - -

Specify whether to output an image for ADF perpendicularity adjustment.

5.1.4.2 Numeric Parameter Functional configuration

0017-6117

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

No. Function Default Setting range Unit

001: - 023: Not used

024: CIS scan position during ADF scanning. 385 300-450 one unit=0.1mm

025: Not used

026: Distance from the standby position of CIS to the 22 6-48 one unit=0.1mm
shading start point.

027: - 030: Not used

031: Vertical scan start position adjustment 35 0-70 one unit=0.1mm

032: Horizontal scan start position adjustment 115 50-150 one unit=0.1mm

033: Vertical scan magnification correction 16 0-32 one unit=0.1%

034: Not used

035: - 036: Reader motor speed adjustment 474

037: - 040: Not used

041: Vertical scan start position adjustment (scanning 35 0-70 one unit=0.1mm
on ADF)

042: Horizontal scan start position adjustment 220 170-270 one unit=0.1mm
(scanning on ADF)

043: Horizontal scan end position correction 24 0-200 one unit=0.1mm

(copy:scanning on ADF)

044: Horizontal scan end position correction 36 0-200 one unit=0.1mm

(superfine:scanning on ADF)

045: Horizontal scan end position correction 47 0-200 one unit=0.1mm

(fine:scanning on ADF)

33
 Chapter 5

No. Function Default Setting range Unit

046: Horizontal scan end position correction 47 0-200 one unit=0.1mm

(standard:scanning on ADF)

047: Vertical scan magnification correction (scanning 16 0-32 one unit=0.1%

on ADF)

048: Horizontal scan magnification correction 16 0-32 one unit=0.1%

(scanning on ADF)

049: - 053: Not used

054: Pickup motor speed correction (when the ADF is 16 0-32 one unit=0.1%
used)

055: - 192: Not used

193: ADF special paper, standardized size: LGL 0 0 : LEGAL
misidentification-ready 1 : FOOLSCAP
2 : M_OFFICIO
3 : A_FOOLSCAP
4 : FOLIO
5 : G_LEGAL
6 : A_OFFICIO
7 : B_OFFICIO

194: ADF special paper, standardized size: LTR 0 0 : LTR

misidentification-ready 1 : G_LTR
2 : A_LTR

195: ADF special paper, standardized size: LTR_R 0 0 : LTR_R

misidentification-ready 1 : FOOLSCAP
2 : OFFICIO
3 : E_OFFICIO
4 : G_LTR_R
5 : A_LTR_R

196: shading target value (red) 272 0-511

197: shading target value (green) 272 0-511

198: shading target value (blue) 272 0-511

199: - 212: Not used

213: XYZ correction value (X) of standard white plate 8273 1-9999

214: XYZ correction value (Y) of standard white plate 8737 1-9999

215: XYZ correction value (Z) of standard white plate 9427 1-9999

216: - 350: Not used

If any operation error occurs after changing the setting value, change the setting value to the original one.

5.1.4.3 <024:CIS scan position during ADF scanning>

0017-6118

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

This value is used when automatic scan position adjustment (TESTMODE>"2"SCAN TEST>"3"SHEET POS ADJ) fails.

5.1.4.4 <026:Distance from the standby position of CIS to the shading start point>
0017-6119

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

White shading can be adjusted finely.

Normally, do not change the setting value. If any operation error occurs after changing the setting value, change the setting value to the original one.

5.1.4.5 <031Vertical scan start position adjustment>

0017-6120

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which vertical scanning of a book starts. The larger the adjustment value, the narrower the left-side margin of the image becomes.

34
 Chapter 5

5.1.4.6 <032Horizontal scan start position adjustment>

0017-6121

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which horizontal scanning of a book starts. The larger the adjustment value, the narrower the top margin in the image becomes.

5.1.4.7 <033Vertical scan magnification correction>

0017-6122

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Correct the magnification of vertical scanning of a book. The larger the adjustment value, the more the image stretches in the vertical scanning direction.

5.1.4.8 <035: - 036:Reader motor speed change>

0017-6123

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Though no market adjustment work needs to be carried out, enter factory defaults at image processor PCB replacement.

5.1.4.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)>
0017-6124

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which vertical scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the left-side margin of the
image becomes.

5.1.4.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)>
0017-6125

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which horizontal scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the top margin of the image
becomes.

5.1.4.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)>

0017-6126

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which horizontal scanning of a document being copied ends (when scanning on a document fed from ADF). The larger the adjustment value,
the narrower the bottom margin of the image becomes.

5.1.4.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)>

0017-6127

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which horizontal scanning of a FAX document scanned in superfine mode ends. The larger the adjustment value, the narrower the bottom
margin of the image becomes.

5.1.4.13 <045: Horizontal scan end position correction (fine:scanning on ADF)>

0017-6128

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which horizontal scanning of a FAX document scanned in fine mode ends. The larger the adjustment value, the narrower the bottom margin
of the image becomes.

5.1.4.14 <046: Horizontal scan end position correction (standard:scanning on ADF)>

0017-6129

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the position at which horizontal scanning of a FAX document set to the standard scan resolution ends. The larger the adjustment value, the narrower the
bottom margin of the image becomes.

5.1.4.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>
0017-6130

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Correct the magnification of vertical scanning of a document fed from the ADF. The larger the adjustment value, the more the image stretches in the vertical scan-
ning direction.

5.1.4.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)>
0017-6131

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Correct the magnification of horizontal scanning of a document fed from the ADF. The smaller the adjustment value, the more the image stretches in the horizontal
scanning direction.
This menu is used to adjust the ADF feed motor speed. If you changed the adjustment value in this mode, the adjustment value selected for SCAN NUMERIC>54
must also be incremented/decremented by the same amount.

Do not change the adjustment value extremely.

5.1.4.17 <193: ADF special standard-sized paper: LGL misidentification-ready>

0017-6132

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LEGAL").
0: LEGAL
1: FOOLSCAP
2: M_OFFICIO
3: A_FOOLSCAP
4: FOLIO
5: G_LEGAL
6: A_OFFICIO
7: B_OFFICIO

35
 Chapter 5

5.1.4.18 <194: ADF special standard-sized paper: LTR misidentification-ready>

0017-6133

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").
0: LTR
1: G_LTR
2: A_LTR

5.1.4.19 <195: ADF special standard-sized paper: LTR_R misidentification-ready>

0017-6134

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTRR").
0: LTR_R
1: FOOLSCAP
2: OFFICIO
3: E_OFFICIO
4: G_LTR_R
5: A_LTR_R

5.1.4.20 <196: Shading Target Value (Red)>

0017-6135

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

This is market-related measures taken to improve shadow images generated by a thick original such as a book or a folded or wrinkled original. When taking the
measures, assign the same values for R, G, and B. After changing the values, be sure to turn off the power and turn it on again.

5.1.4.21 <197: Shading Target Value (Green)>

0017-6136

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

This is market-related measures taken to improve shadow images generated by a thick original such as a book or a folded or wrinkled original. When taking the
measures, assign the same values for R, G, and B. After changing the values, be sure to turn off the power and turn it on again.

5.1.4.22 <198: Shading Target Value (Blue)>

0017-6137

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

This is market-related measures taken to improve shadow images generated by a thick original such as a book or a folded or wrinkled original. When taking the
measures, assign the same values for R, G, and B. After changing the values, be sure to turn off the power and turn it on again.

5.1.4.23 <213: XYZ correction value (X) of standard white plate> (if equipped with SEND functions))
0017-6138

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If you replaced the image processor PCB, enter values indicated on the service label. If you have replaced the document glass, enter values indicated on the new
document glass and write the values on the service label.

820686679349

correcton correcton
va l u e ( X ) correcton va l u e ( Z )
va l u e ( Y )
F-5-2

5.1.4.24 <214: XYZ correction value (Y) of standard white plate> (if equipped with SEND functions)
0017-6139

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If you replaced the image processor PCB, enter values indicated on the service label. If you have replaced the document glass, enter values indicated on the new
document glass and write the values on the service label.

820686679349

correcton correcton
va l u e ( X ) correcton va l u e ( Z )
va l u e ( Y )
F-5-3

5.1.4.25 <215: XYZ correction value (Z) of standard white plate> (if equipped with SEND functions)
0017-6140

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If you replaced the image processor PCB, enter values indicated on the service label. If you have replaced the document glass, enter values indicated on the new
document glass and write the values on the service label.

36
 Chapter 5

820686679349

correcton correcton
va l u e ( X ) correcton va l u e ( Z )
va l u e ( Y )
F-5-4

5.1.5 Printer Function Settings (PRINTER)

5.1.5.1 Service Soft Switch Settings
5.1.5.1.1 SSSW-SW05

List of Functions
0017-6141
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-20

Bit Function 1 0

0 not used - -

1 not used - -

2 not used - -

3 not used - -

4 not used - -

5 not used - -

6 not used - -

7 priority on recording in sub scanning direction place do not place

Detailed Discussions of Bit 7

0017-6142
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to enable/disable placement of priority on recording in sub scanning direction.

T-5-21

place: if B4 recording paper and A4 recording paper are set and an A4 extra-long image
(*) is received, printing will be on the B4 recording paper.

do not place: if B5 horizontal recording paper and A4 recording paper are set and a B4 image is
received, printing will be by division and on B5 horizontal recording paper.

*: Image B4 or shorter and that cannot be printed by division and on A4 recording paper.
5.1.5.1.2 SSSW-SW14

List of Functions
0017-6143
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-22

Bit Function 1 0

0 Transfer bias pressure reduction mode Enable Disable

1 Developing assembly idling mode Enable Disable

2 Black belt addition mode Enable Disable

3 Post-rotation reduction mode Enable Disable

37
 Chapter 5

Bit Function 1 0

4 Flicker reduction mode Enable Disable

5 Silent mode Enable Disable

6 Terminal temperature rise noise reduction mode Enable Disable

7 Not used - -

Detailed Discussions of Bit 0

0017-6144
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to enable or disable transfer bias pressure reduction mode.

Select "Enable" to avoid image defects (black spots) produced by transfer bias leaks occurring in a low-pressure region, such as one at a high altitude. This setting
regulates the transfer bias to keep it from exceeding a predetermined level during printing.
Detailed Discussions of Bit 1
0017-6146
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to enable or disable developing assembly idling mode. Select "Enable" to drive the main motor for a specified period of time to apply idling and
developing bias (AC + DC) to prevent the thinning of the image density when the unit is installed or the developing unit is replaced in a low-temperature, low-
humidity region. This mode works only on a new developing assembly and before a toner cartridge is loaded.
Detailed Discussions of Bit 2
0017-6147
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to enable or disable black belt addition mode. If the user uses paper that causes fixed toner on paper to be fused and adhered to drum, selecting
"Yes" will clean the drum by forming a black band on the drum surface during the reverse rotation which is performed after printing on 50 sheets.

Implementation of this mode could result in a drum life falling short of its life expectancy.

Detailed Discussions of Bit 3

0017-6148
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Select whether to enable or disable post-rotation reduction mode. Selecting "Enable" will reduce the noise caused by the polygon motor by stopping the motor
immediately after post-rotation.
Detailed Discussions of Bit 4
0017-6149
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to enable or disable flicker reduction mode. Select "Enable" and enter a count to modify fusing temperature control to cancel fluorescent flicking
during printing.

Implementation of this mode would degrade the throughput.

Detailed Discussions of Bit 5

0017-6150
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to enable or disable silent mode. Select "Enable" to modify the registration loop amount and thus reduce noises or squeaks the registration rollers
produce after picking paper from the individual paper inlets.
Detailed Discussions of Bit 6
0017-6151
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to enable or disable noise reduction mode during terminal temperature rises. Select "Enable" to start slowdown at a temperature lower than normal
when printing on smaller-sized paper than B4. Slowdown control thus enabled prevents the thermal degradation of the fusing film grease, assuring smooth sliding
among the fixing film, heater and film guide to cut squeaks.
5.1.5.1.3 SSSW-SW15

List of Functions
0017-6152
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-23

Bit Function 1 0

0 Inhibit automatic delivery tray replacement while running Enable Disable

jobs

38
 Chapter 5

Bit Function 1 0

1 Halt stapling job when out of staples Enable Disable

2 Inhibit tray full indication while the stapled document Enable Disable
count is exceeded

3 IFAX Permission of split recording of text data Enable Disable

4 Not used - -

5 Not used - -

6 Not used - -

7 Not used - -

Detailed Discussions of Bit 0

0017-6153
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to inhibit automatic delivery tray replacement while running jobs with an inner two-way tray mounted in position. Select "Enable" to inhibit auto-
matic tray replacement.
Detailed Discussions of Bit 1
0017-6154
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to halt stapling job when a finisher installed has run out of staples. Select "Enable" to halt staple jobs when the finisher has run out of staples.
Detailed Discussions of Bit 2
0017-6155
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether to display a tray full message when the maximum allowable stapled document count is exceeded with a finisher installed. Select "Enable" not to
display the message.
Detailed Discussions of Bit 3
0017-8532
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Select whether split recording is to be enabled when text data such as a header and body text is recorded. Selecting "Set" may split text data when a small paper size
such as A5 is selected. In this case, a page may be split in the middle of a character string.
5.1.5.1.4 SSSW-SW18
List of Functions
0017-8533
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

T-5-24

Bit Function 1 0

0 Limit temperature of temperature adjustment Enable Disable

1 Shift of the temperature adjustment when at auto duplex Enable Disable

2 Thin post card mode Enable Disable

3 Not used - -

4 Not used - -

5 Not used - -

6 Not used - -

7 Not used - -

Detailed Discussions of Bit 0

0017-8534
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If there is no progress after shifting the target figure of the temperature adjustment using "Temperature Adjustment UP/DOWN Mode", # PRINTER> Numeric>

39
 Chapter 5

Parameter 62, 63, cancel the inner limit of the fixed temperature adjustment.
To cancel the inner limit of the fixed temperature adjustment, select "Setting".
Detailed Discussions of Bit 1
0017-8535
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If there is no progress after shifting the target figure of the temperature adjustment using "Temperature Adjustment UP/DOWN Mode", # PRINTER> Numeric>
Parameter 62, 63, cancel the 2nd face of the duplex inner limit of the fixed temperature adjustment.
Select "Setting" to cancel the 2nd face of the duplex inner limit of the fixed temperature adjustment.
Detailed Discussions of Bit 2
0017-8536
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

When selecting the post cards, besides the 'Reply post card', 'Post card', and the 'Four face post card', 'Thin post card' could be selected. Select 'Setting' and 'Thin
post card' would be selected.
5.1.5.2 Numeric Parameter Settings (NUMERIC Param.)
5.1.5.2.1 List of Functions
0017-6156
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

No. Function Default Setting range

01: - 30: Not used
31: Top registration adjustment (manual feed tray) 50 0 to 100, one unit = 0.1 mm
32: Top registration adjustment (cassette) 50 0 to 100, one unit = 0.1 mm
33: Top registration adjustment (duplex unit) 50 0 to 200, one unit = 0.1 mm
34: Left-end registration adjustment (manual feed tray) 100 0 to 200, one unit = 0.1 mm
35: Left-end registration adjustment (cassette 1) 100 0 to 200, one unit = 0.1 mm
36: Left-end registration adjustment (cassette 2) 100 0 to 200, one unit = 0.1 mm
37: Left-end registration adjustment (cassette 3) 100 0 to 200, one unit = 0.1 mm
38: Left-end registration adjustment (cassette 4) 100 0 to 200, one unit = 0.1 mm
39: Left-end registration adjustment (duplex unit) 100 0 to 200, one unit = 0.1 mm
40: Target fixing temperature adjustment (multi) 6 -30 to 0, one unit = 5 deg C
41: Target fixing temperature adjustment (cassette 1) 6 -30 to 0, one unit = 5 deg C
42: Target fixing temperature adjustment (cassette 2) 6 -30 to 0, one unit = 5 deg C
43: Target fixing temperature adjustment (cassette 3) 6 -30 to 0, one unit = 5 deg C
44: Target fixing temperature adjustment (cassette 4) 6 -30 to 0, one unit = 5 deg C
45: Fixing film speed change (manual feed tray) 16 0 to 30, 1 unit = 0.4%
46: Fixing film speed change (cassette) 16 0 to 30, 1 unit = 0.4%
47: - 52: Not used
53: Adjustment of margin at leading edge of copy 0 0 to 9999, one unit = 0.1 mm
54: Adjustment of margin at trailing edge of copy 0 0 to 9999, one unit = 0.1 mm
55: Adjustment of margin at right edge of copy 0 0 to 9999, one unit = 0.1 mm
56: Adjustment of margin at left edge of copy 0 0 to 9999, one unit = 0.1 mm
57: Not used
58: Adjustment of the registration loop volume (Manual 100 85 to 115, one unit = 0.5 mm
tray)
59: Adjustment of the registration loop volume (Cassette) 100 85 to 115, one unit = 0.5 mm
60: Adjustment of the registration loop volume (Optional 100 85 to 115, one unit = 0.5 mm
cassette)
61: Adjustment of the registration loop volume (Duplex 100 85 to 115, one unit = 0.5 mm
unit)
62: Temperature adjustment UP/DOWN mode (For 7 0 to 14, one unit = 5 deg C
normal paper)
63: Temperature adjustment UP/DOWN mode. (For thick 7 0 to 14, one unit = 5 deg C
paper)
64: Mode for preventing the end temperature rise 0 0 to 5
65: Mode for reducing sand image 0 0 to 3
66: Temperature/ Humidity sensor fixed mode 0 0 to 3
67: - 70: Not used

5.1.5.2.2 <031: Top registration adjustment (manual feed tray)>

0017-6157
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Adjust the top registration margin of paper picked from a manual feed tray. The larger the adjustment value, the wider the top margin of the image becomes.
5.1.5.2.3 <032: Top registration adjustment (cassette)>
0017-6158
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

40
 Chapter 5

Adjust the top registration margin of paper picked from cassettes. The larger the adjustment value, the wider the top margin of the image becomes.
5.1.5.2.4 <033: Top registration adjustment (duplex unit)>
0017-6159
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the top registration margin of paper picked from a duplex unit. The larger the adjustment value, the wider the top margin of the image becomes.
5.1.5.2.5 <034: Left-end registration adjustment (manual feed tray)>
0017-6160
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the left-end registration margin of paper picked from a manual feed tray. The larger the adjustment value, the wider the left-end margin of the image be-
comes.
5.1.5.2.6 <035: Left-end registration adjustment (cassette 1)>
0017-6162
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the left-end registration margin of paper picked from cassette 1. The larger the adjustment value, the wider the left-end margin of the image becomes.
5.1.5.2.7 <036: Left-end registration adjustment (cassette 2)>
0017-6163
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the left-end registration margin of paper picked from cassette 2. The larger the adjustment value, the wider the left-end margin of the image becomes.
5.1.5.2.8 <037: Left-end registration adjustment (cassette 3)>
0017-6164
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the left-end registration margin of paper picked from cassette 3. The larger the adjustment value, the wider the left-end margin of the image becomes.
5.1.5.2.9 <038: Left-end registration adjustment (cassette 4)>
0017-6165
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the left-end registration margin of paper picked from cassette 4. The larger the adjustment value, the wider the left-end margin of the image becomes.
5.1.5.2.10 <039: Left-end registration adjustment (duplex unit)>
0017-6166
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the left-end registration margin of paper picked from a duplex unit. The larger the adjustment value, the wider the left-end margin of the image becomes.
5.1.5.2.11 <040: Target fixing temperature adjustment (manual feed tray)>
0017-6167
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Lower the fixing temperature from the target temperature setting to reduce the chances of fixing offsets and curled or stuck delivered sheets occurring with paper
picked from a manual feed tray.
5.1.5.2.12 <045: Fixing film speed change (manual feed tray)>
0017-6172
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Change the fixing film speed to reduce the chances of streaks appearing in the trailing edge of images caused by shocks from the fixing roller out of position while
picking paper from a manual feed tray.
5.1.5.2.13 <046: Fixing film speed change (cassette)>
0017-6173
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Change the fixing film speed to reduce the chances of streaks appearing in the trailing edge of images caused by shocks from the fixing roller out of position while
picking paper from a cassette.
5.1.5.2.14 <053: Margin adjustment at the leading edge of the copy>
0017-6168
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the margin at the leading edge of the copy. Increasing the value makes the margin at the leading edge larger.
5.1.5.2.15 <054: Margin adjustment at the trailing edge of the copy>
0017-6169
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the margin at the trailing edge of the copy. Increasing the value makes the margin at the trailing edge larger.
5.1.5.2.16 <055: Margin adjustment at the right edge of the copy>
0017-6170
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the margin at the right edge of the copy. Increasing the value makes the margin at the right edge larger.

41
 Chapter 5

5.1.5.2.17 <056: Margin adjustment at the left edge of the copy>

0017-6171
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Adjust the margin at the left edge of the copy. Increasing the value makes the margin at the left edge larger.
5.1.5.2.18 <058:: Adjustment of the registration loop volume (Manual feed tray)>
0017-8644
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If there is a registration loop noise and abrasion while feeding the paper from the manual feed tray, registration loop noise and abrasion could be reduced by adjusting
the volume of the registration loop. By making the value larger, loop volume will become bigger.
5.1.5.2.19 <059:Adjustment of the registration loop volume. (Cassette)>
0017-8645
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If there is a registration loop noise and abrasion while feeding the paper from the cassette, registration loop noise and abrasion could be reduced by adjusting the
volume of the registration loop. By making the value larger, loop volume will become bigger.
5.1.5.2.20 <060:Adjustment of the registration loop volume (Option cassette)>
0017-8646
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If there is a registration loop noise and abrasion while feeding the paper from the option cassette, registration loop noise and abrasion could be reduced by adjusting
the volume of the registration loop. By making the value larger, loop volume will become bigger.
5.1.5.2.21 <061:Adjustment of the registration loop volume. (Duplex unit)>
0017-8648
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

If there is a registration loop noise and abrasion while feeding the paper from the duplex unit, registration loop noise and abrasion could be reduced by adjusting
the volume of the registration loop. By making the value larger, loop volume will become bigger.
5.1.5.2.22 <062:Temperature adjustment UP/DOWN mode. (For plain paper)>
0017-8649
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
For plain paper relation, the volume of the temperature adjustment offset could be changed by 5 deg C at a time to aim the fixed temperature.
For plain paper relation : Normal, Normal Lo, rough paper Lo, thin post card, and OHP mode.
0 to 6: -35 to -5 deg C (1unit=5deg C)
7: 0 deg C
8 to 14: +5 to +35 deg C (1unit=5deg C)
5.1.5.2.23 <063:Temperature adjustment UP/DOWN mode. (For rough paper)>
0017-8650
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

For rough paper relation, the volume of the temperature adjustment offset could be changed by 5 deg C at a time to aim the fixed temperature.
For rough paper relation: rough paper, super rough paper, super rough paper H, post card, post card H, and envelope mode.
0 to 6: -35 to -5 deg C (1unit=5deg C)
7: 0 deg C
8 to 14: +5 to +35 deg C (1unit=5deg C)
5.1.5.2.24 <064:Mode for preventing the temperature rise of the end >
0017-8651
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set when the fixed film squeaks. Lower the target fixing temperatue and extend sheet-to-sheet time except A4/A3/11X17/LTR size.
0: Normal
1 to 5: Mode for responding film squeak. (reference to the table below)
T-5-25

Setting Print temperature control Sheet-to-sheet temperature control Sheet-to-sheet time

1 Target temperature-10 deg C Print temperature control -20 deg C 0 sec extension
2 Target temperature-20 deg C Print temperature control -20 deg C 0 sec extension
3 Target temperature-10 deg C Print temperature control -20 deg C 10 sec extension
4 Target temperature-20 deg C Print temperature control -20 deg C 10 sec extension
5 Target temperature-30 deg C Print temperature control -20 deg C 15 sec extension

5.1.5.2.25 <065:Mode for reducing sand image>

0017-8655
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Set when sand image *1 has occurred on the print image.

Restraining the scatter of the toner by increasing the electric current of the AC electrification; the sand image could be reduced.
Sand image *1: Multiple black dots and white dots appear on half tone. Or multiple black dots appear on white background.
0: Normal.
1 to 3: Reducing mode. (Same operation to set 1 to 3)

42
 Chapter 5

There is a possibility that when using the "Reducing mode", the life of the drum will not meet the specified pieces.

5.1.5.2.26 <066:Temperature/ Humidity sensor fixed mode>

0017-8656
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Changing to high-pressure environment by using the temperature/ humidity sensor. But when there is an image trouble at the point of changing the environment,
fix the temperature and the humidity and do not allow the change of the high-pressure output.
0: Normal
1: Fixed environment of LL. (Temperature of 10 deg C and humidity of 10%)
2. Fixed environment of NN. (Temperature of 20 deg C and humidity of 50%)
3. Fixed environment of HH. (Temperature of 30 deg C and humidity of 80%)
5.1.5.3 Setting of Cassette (CST)
5.1.5.3.1 Special Standard-sized Paper Compatibility
0017-6174
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

With a special paper compatibility kit (cassette size adjuster) installed, set the cassette paper size lever to paper size groups U1 to U3 to set the paper sizes listed
below.

Paper size group Setting (*default) Paper name Marking

U1 0* Government LETTER G-LTR

29 Argentine LETTER A-LTR
31 Government LETTER G-LTR
40 8K 8K
U2 0* FOOLSCAP FLSP
24 FOOLSCAP FLSP
26 OFFICIO OFI
27 Ecuadorian OFFICIO E-OFI
28 Bolivian OFFICIO B-OFI
36 Argentine Offico A-OFI
37 Mexican OFFICIO M-OFI
39 16K 16K
U3 0* Government LEGAL G-LGL
25 Australian FOOLSCAP AFLS
30 Argentine LETTERR ALTRR
32 Government LETTERR FLTRR
34 Government LEGAL G-LGL
35 FORIO FORIO

5.1.6 Network Parameter Settings (NETWORK)

5.1.6.1 Confirmation of contents of CA certificate

0017-6175

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Selecting the service mode "#NETWORK>#CERTIFICATE>#CA-CERTIFICATE" enables confirmation of the contents of the installed CA certificate.

5.1.7 Setting of System Functions (SYSTEM)

5.1.7.1 Bit Switch Settings

0017-6177

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

SSSW-SW03 functional configuration

T-5-26

Bit Function 1 0

0 Not used - -

1 Not used - -

2 Not used - -

3 Not used - -

4 Not used - -

5 Not used - -

6 Imports and exports user information via USB. Enable Disable

43
 Chapter 5

Bit Function 1 0

7 Not used - -

Bit 6 details
Select whether to enable the host machine to work as a USB storage device or not. If the host machine is plugged into a PC with this setting enabled, it allows user
registration data (user data and telephone registration data) to be imported and exported to and from the PC, except for the data embedded in the department man-
agement information and user management IDs in the system management information.

5.1.8 Registration of Accessories (ACC)

5.1.8.1 Accessory Registration

0017-6178

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The table below gives summary description of the accessories available.

Item Explanation

#ACC CARD Card reader installation setting

Enter a card number to use.
(0 to 9999. One hundred cards are registered with the department ID beginning from the input card number in sequence.)
*1:1,000 cards if option ROM is mounted.
When a card number is entered, the following kinds of management information are initialized:
- Card name (department ID), beginning from the input card number.
- Password associated with the card

CC-SPSW Control card I/F support setting

Set whether to support the control card I/F (CC-V) or not.
0: Do not support.
1: Support.

COIN Coin vendor change

Set the control card set display appearing on the operator station for vendor use.
0: Control card use
1: Coin vendor use

CONTROL Set the PDL printer output control where the control card I/F (CC-V) is supported.
0: Enable printing without a card mounted.
1: Enable printing with a card mounted in position.

5.1.9 License Management (LMS)

5.1.9.1 Outline
0017-8537

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

LMS (License Management Service)

License Management System is to acquire a figure row from sending the information of the license certificate number, which is in the same package as option
product, machine serial number and the name of the main machine to the server that has a license issue function on the Internet.
Option function will be able to be used by inputting the acquired figures from the main machine operation board through license registration screen in the users
mode.
License option function is implemented on all the main system of the products, which is shipped from the factory, but it would not activate unless input operation
has been made through the license registration screen.
Acquisition of the license key and registration of the device is basically done by the user. Detailed procedure is described in the users guide. However, as for ref-
erence, summary of the procedure is mentioned below.

(1) Access to LMS from the below URL and follow the direction on the screen to acquire the license key.
URL for LMS
http://www.canon.com/lms/license/

MEMO:
To acquire the license key, 16 digit figures on the license access number certificate and the device serial number (for example: ABC01234), which the license is
going to be installed is necessary.
Device serial number will indicate on "Serial Number" when pressing the counter confirmation key on the main machine.

(2) Copy the license key of 24 digit figures, which is indicated on the WEB browser to the designated column on license access number certificate.

Reconfirm that there is no miss-copy of the 24 digit figures. Explain to the user that license access number certificate should be kept with care.

(3) Input the copy of the license key from; user mode > system management setting> license registration and press enter. The license key will be registered and
function will activate.
If the function do not activate, error message will indicate. Confirm the points below due to contents of the error message.

"Value of the license key is incorrect. Confirm license key"

>> Using the license key, which was issued to another device?
>> Incorrect license key was input?
>> Proper license key used?
"This function is already active"
>> Isn't the relevant kit already active?
(4) Switch off the main power supply and after 10 seconds switch on the power supply again.

44
 Chapter 5

(5) Registered license will be active when after the power supply of the main device switch has been cut off once and put on again. Once the license starts properly,
press counter confirmation key then press device configuration and confirm that in the option column that the relevant kit has been indicated.

5.1.9.2 Method of confirming license option

0017-8538

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Confirmation could be made whether the license option is active or not in the SOFT-ID PRM item by outputting the SPEC REPORT from the service mode.
Output method:
Select '# REPORT' from service mode.
Select '# REPORT OUTPUT'.
Select '# REPORT OUTPUT SPEC LIST' and press 'OK'.

Check the SOFT-ID RPM column from the SPEC REPORT output. License is active on the items which indicates 'ON/ON'.
Related items:
BIT 00: BDL-IMAGE(1200) -> CARPS2
BIT 05: BW-SEND -> SEND
BIT 06: CL-SEND -> SEND
BIT 09: BDL-IMAGE( 600) -> CARPS2

5.1.9.3 Inactivity of the transmitted license

0017-8539

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Inactivity of the transmitted license

Situation of using this service mode

This service mode is to be used exceptionally on the assumption that when malfunction occurs on the device (caused by device) and the license to be transferred to
the substitute device and to inactivate the license.
This operation is called ' Inactivity of the transmitted license'. Transmission could be selected to the same device and could be used to cease the function temporary.
But if the license is made inactive by mistake, it is necessary to call the dealer to reactivate.

Take utmost precaution when inactivating the license

To inactive the license, operation through the service mode has to be made and to prove the function is inactive; issue of the function inactive certificate key is
necessary.
This operation is valid to any of the each optional function and at the point of issuing the function inactive certificate key the function will be inactive and could
not be used.
New license key to install to the transmitted device will be issued when the information of function inactive certificate key, serial number of the transmission origin
device, serial number of new destination of transmitting device and the reason for transmitting is given to the dealer. Take a note of the new license key and after
the registration to the new transmitted device, inform the user that the new license key should be kept with care.

Operation procedures

(1) Go into the service mode and indicate the below mentioned service mode. (Key operation to go into the service mode is to be pressed one at a time. Orders are
*, 2, 8, *).
After going into the service mode, use the arrow on the both sides of the touch panel and press 'OK' if the decision is made.
(2) Indicate '#LMS'.
(3) Press 'OK' and indicate '#LMS INACTIVE'.
(4) Indicate 'BDL-IMAGE (CARPS 2 for Japanese market) or 'SEND'.
(5) Press 'OK'.
(6) Press '2' from the numeric keypad and press 'OK'.

#SEND

001 1 Press '2' from the numeric

keypad and press 'OK'.

OK
F-5-5

1.Take a note of the license transmit number which will be indicated with 24 digits.
2.The indicated number is just for this operation and it would not be saved.
3.If the power is switched off, the indicated number will disappear and if the note of the number has not been taken, transmission of the license will be impossible.
4.Even pressing the reset key to clear the indication, there will be no recovery of the number.

Example of the transmitted license indication:

F-5-6
(7) Switch the power supply OFF/ON of the main machine.

45
 Chapter 5

Reference:
At procedure (4) when indicating the license option, it indicates ' 001 1'. The last digit '1' shows that the license is active.
After transmitting the license the last digit will change to '2', which means that the license has been transmitted.
If the option is standard equipped, the last digit will indicate '3', which means that the license could not be transmitted.

(8) Contact the dealer and inform the function inactive certificate key, serial number of the transmission origin device, and serial number of new transmiting device,
which is necessary to transmit the license.
Upon given information above, new license key will be issued, which the license could be registered to the new transmitting device.
(9) Register the new license key to the transmitted device and confirm that the function is active.

5.1.10 eRDS Parameter Settings (E-RDS)

5.1.10.1 Settings Related to e-RDS

0017-6179

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Settings related to e-RDS are described below.

T-5-27

Item Description
E-RDS SWITCH e-RDS OFF/ON setting (0:OFF / 1:ON)When used (ON), the counter information and error information are sent
to UGW.Default: 0 (OFF)

RGW-ADDRESS URL of UGWDefault: URL of actual UGWCharacter string length: 129 bytes (including NULL, one-byte codes
only)

RGW-PORT Port No. of UGW Default: 443Setting range: 1 to 65535

COM-TEST Execution of communication test An attempt is made to connect to UGW, judges whether connection is
successful, and displays "COM-TEST OK" or "COMTEST NG" as the judgment result.

COM-LOG Details of communication test resultThe log of errors in communication with UGW is displayed. The error
information includes the error occurrence time, error code, and details of the error.Maximum log count: 5Error
information length: Max. 128 characters (excluding NULL)

5.1.11 Display of Counter Information (COUNTER)

5.1.11.1 Counters
0017-6180

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

This copier is furnished with a maintenance/supplies counter set (DRBL-1), which can be used to gain rough measures of when to replace supplies. The counter
set increments by one on counting each sheet of small-sized paper (up to A4/LTR) and by two on counting each sheet of large-sized paper (larger than A4/LTR).
T-5-28

Maintenance counter list

Item Counter Explanation

TOTAL (Total counter) SERVICE1 Service total counter 1

SERVICE2 Service total counter 2
TTL Total counter
COPY Total copy counter
PDL-PRT PDL print counter
FAX-PRT Fax print counter
REP-PRT Report print counter
2-SIDE Double-sided copy/print counter
SCAN Scan counter
PICK-UP (Paper pickup counter) C1 Cassette 1 jam counter
C2 Cassette 2 jam counter
C3 Cassette 3 jam counter
C4 Cassette 4 jam counter
MF Manual feed tray pickup total counter
2-SIDE Double-sided paper pickup total counter
FEEDER (Feeder related counters) FEED Feeder pickup total counter
DFOP-CNT ADF open/close hinge counter

46
 Chapter 5

Maintenance counter list

Item Counter Explanation

JAM (Jam counters) TTL Unit total jam count

FEEDER Feeder total jam count
SORTER Finisher total jam count
2-SIDE Duplex unit jam counter
MF Manual feed tray jam counter
C1 Cassette 1 jam counter
C2 Cassette 2 jam counter
C3 Cassette 3 jam counter
C4 Cassette 4 jam counter
MISC (Other required counter) WST-TNR Waste toner counter

T-5-29

Parts counter list

Item Counter Explanation Service life
DRBL-1 (Unit supplies) FX-UNIT Fixing unit paper pass count 150,000

TR-ROLL Transfer charger roller high-voltage ON count 150,000

DV-UNT-C Developing unit rotation count 150,000

M-PU-RL Manual feed tray pickup roller paper pass count 150,000

M-SP-PD Manual feed tray separation pad paper pass count 150,000

5.1.11.2 Clearing Counters

0017-6181

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

- Maintenance/parts counter all clear
Execute service mode > CLEAR > COUNTER to clear all maintenance/parts counters.

- Counter clear on parts replacement

Press the numeric keypad key 0 after displaying the counter for a part just replaced, and the counter will be cleared individually.

5.1.12 Report Output (REPORT)

5.1.12.1 Report Output

0017-6185

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The table below lists the kinds of reports that are supported.

Item Explanation

SERVICE DATA LIST Service mode service soft switch output (SSSW, MENU, NUMERIC Param., SPECIAL, NCU, SCAN, PRINT, SYSTEM, ROM,
start date)

SYSTEM DATA LIST Service mode service soft switch output (SSSW, MENU, NUMERIC Param., SPECIAL, NCU, SCAN, PRINT, SYSTEM, ROM,
start date)
System dump list output

SYSTEM DUMP LIST Transmission count, reception count, record chart count, error count and other outputs

COUNTER REPORT Counter output

ERROR LOG LIST Jam and error history output

SPEC LIST Type setting, print speed, memory size, ROM indication, adjustment data and other outputs

SERVICE LABEL Output of an entry format for the service label affixed to the rear cover as shipped

ERDS COM LOG LIST Output of communication error log information related to e-RDS

ENV. LOG LIST Output of environmental log information

5.1.12.2 System Data List

0017-6186

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to check the settings associated with the service soft switch and service parameters.

47
 Chapter 5

    


    



  
  
  

 
  
  
  
  
  
  
  
  
  

 
  
  
  
  
  
  
  
  
  

 
  
  
  
  
  
   
   
   
  

 
   
   
  
   
   

  

  

  

 


 

  

  

 

  

  
  


  
  
   

  
  

F-5-7

5.1.12.3 System Dump List

0017-6187

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

- System Dump List

Use it to check the history of communications, both successful and error.

[1]
[3]
[2]
[3]
[4]

[5]
[6]
[7]

[8]

[9]

F-5-8
*1: TX, number of total pages transmission.
*2: Total number of pages transmitted/received according to original size.
*3: RX, number of total pages reception.
*4: Total number of pages transmitted and received for each modem speed
*5: Total number of pages transmitted/received in connection with different modem speeds (Standard, Fine, Super Fine, Ultra Fine).
*6: Total number of pages transmitted and received for each coding method

48
 Chapter 5

*7: Total number of pages transmitted and received in each mode

*8: Total number of pages printed/scanned
*9: Total number of occurrences for error code

T-5-30

Indication
sample
##280 1 7 3 0 0

##280 ##281 ##282

number of errors number of errors number of errors

It provides error information on the 3 most recent communications.

    
 


   

      

     

   !


   " !


  # #$   
 !  
 %    &'()
 !     &*+ ,#$ -
  # ! "
  % !
   %
   %

  .  / &01
2





















/ &01  2

 / &01  2


/ &01  2
  .  / &01
2











/ &01  2
 / &01  2


/ &01  2

 .  "  !     

 .  "  !  3 3" 3 3" 3 3"

.       

.  3 3" 3 3 ! "

 

      
    

  !


  " !


  # #$   
 !  
 %    &'()
 !     &*+ ,#$ -
  # ! "
  % !
   %
   %

 .  / &01
2





















/ &01  2

 / &01  2


/ &01  2
 .  / &01
2











/ &01  2
 / &01  2


/ &01  2

.  "  !     

.  "  !  3 3" 3 3" 3 3"

.       

.  3 3" 3 3 ! "

 !  

      
    

  !


  " !


  # #$   
 !  
 %    &'()
 !     &*+ ,#$ -
  # ! "
  % !
   %
   %

F-5-9
*1: service error code.
*2: START TIME, date and time (in 24-hr notation).
*3: OTHER PARTY, telephone number sent by the other party.
*4: MAKER CODE, manufacturer code.
*5: MACHINE CODE, model code.
*6: bit 1 through bit 96 of DIS, DCS, or DTC that has been received.
*7: bit 1 through bit 96 of DIS, DCS, or DTC that has been transmitted.
*8: RX, procedural signal received; TX, procedural signal transmitted.

5.1.12.4 Counter List

0017-6188

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Explanation: Maintenance/supplies counter output.
(For more detailed information about the maintenance/supplies counter output, execute service mode > Display counter information > Counters.)

5.1.12.5 Error Log List

0017-6189

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

49
 Chapter 5

07/12/2005 13:07 FAX 001

***************************************
*** JAM/ERR LOG REPORT ***
***************************************

[1] [2] [3] [4] [5] [6] [7] [8] [9] [10]

JAM
01 04/12 12:17 20:03 4 1 0012 000026 1 A4

20 04/12 12:17 20:03 4 1 0012 000026 1 A4

[1] [2] [3] [4] [5] [6] [7] [8]

ERR
01 04/12 12:17 15:36 3 0010 0000 000691

20 04/12 12:17 15:36 3 0010 0000 000691

F-5-10

Jam history description (JAM)

Item Explanation
[1] Number The larger the number of a jam, the more recently it has occurred.
[2] Jam date Date of jam occurrence
[3] Jam time
[4] Jam recovery time
[5] Location 3: Host machine, 4: ADF, 5: Finisher
[6] Occurrence category 0: Host machine, 1: ADF, 2: Finisher

50
 Chapter 5

Jam history description (JAM)

Item Explanation
[7] Jam code Code Jam cause
Host machine 0104 Pickup assembly delay jam
0208 Pickup assembly stationary jam
010c Delivery assembly jam
010e Second delivery assembly delivery delay jam
0210 Delivery stationary jam
0212 Second delivery assembly stationary jam
0214 Host machine retention paper jam
1118 Door open jam
0120 Duplexing paper sensor 1 delay jam
0221 Duplexing paper sensor 1 stationary jam
0124 Duplexing paper sensor 2 delay jam
0228 Duplexing paper sensor 2 stationary jam
ADF 0000 Unknown jam
0007 Initial stationary
0008 Read sensor delay jam
0009 Read sensor stationary jam
000a Paper absence (Pull out the document.)
000c Delivery reversal sensor delay jam
000d Delivery reversal sensor stationary jam
000e ADF cover open error
000f User ADF open error
0010 Pickup NG
Finisher 0130 Inlet sensor delivery delay jam
0231 Inlet sensor delivery stationary jam
0033 Bundle delivery jam
0035 Stapler jam
1036 Power-on jam
1137 Door open jam
[8] Total counter display
[9] Pickup stage position 0: Manual feed tray, 1: Cassette 1, 2: Cassette 2, 3: Cassette 3, 4: Cassette 4
[10] Paper size

Error history description (ERR)

Item Explanation
[1] Number The larger the number of an error, the more recently it has occurred.
[2] Error date Date of error occurrence
[3] Error time
[4] Location 3: Main unit, 5: Finisher
[5] Error code Error code (4-digit code; for a definition of the code, see the "Error Code" Chapter.)
[6] Detail code Detail code of the error code (4-digit code; for a definition of the code, see the "Error Code"
Chapter.)
[7] Total counter display

5.1.12.6 Spec List

0017-6190

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

51
 Chapter 5

07/12/2005 13:07 FAX 001

[1] *****************************
[2] *** SPEC REPORT ***
*****************************
[3]
TYPE _____ JAPAN
LBP SPEED _____ 25cpm
TOTAL MEMORY _____ 256MB
MAIN _____ WLaa-08-01
_____
[4] OPTION
_____
WLaa-08-01
BOOT WLaa-08-01
LANG _____ WLaa-08-01
LANG LIBRARY (QVGA) _____ 000C0000
LANG FILE (QVGA)
ENGLISH _____ 000C0000
JAPANESE _____ 000C0000
BULGARIAN _____ 000C0000
CATALAN _____ 000C0000
CZECH _____ 000C0000
DANISH _____ 000C0000
SPANISH _____ 000C0000
ESTONIAN _____ 000C0000
FINNISH _____ 000C0000
FRENCH _____ 000C0000
GERMAN _____ 000C0000
GREEK _____ 000C0000
CROATIAN _____ 000C0000
HUNGARIAN _____ 000C0000
ITALIAN _____ 000C0000
DUTCH _____ 000C0000
NORWEGIAN _____ 000C0000
POLISH _____ 000C0000
PORTUGUESE _____ 000C0000
ROMANIAN _____ 000C0000
RUSSIAN _____ 000C0000
SLOVAK _____ 000C0000
SLOVENE _____ 000C0000
SWEDISH _____ 000C0000
TURKISH _____ 000C0000
ECONT _____ 0309
OPT-CAS 1 _____ 0000
OPT-CAS 2 _____ 0000
OPT-CAS 3 _____ 0000
OPT-DUP _____ 0000
OPT-FIN _____ 0000
ACTIBAT FUNCTION
BDL-IMAGE (1200) _____ OFF
[5] FAX _____ ON
NETWORK _____ ON
PCL _____ ON
PC-SCAN _____ ON
BW-SEND _____ OFF
CL-SEND _____ OFF
PAF _____ OFF
BDL-IMAGE (600) _____ OFF
E-RDS _____ OFF
BAR-DIMM _____ OFF
SOFT-ID PRM
TYPE _____ 0 : NONE
[6] OPTION/ENABLE SW
BIT 00: BDL-IMAGE (1200) _____ ON / OFF
BIT 01: FAX _____ ON / OFF
BIT 02: NETWORK _____ ON / OFF
BIT 03: PCL _____ ON / OFF
BIT 04: PC-SCAN _____ OFF / OFF

F-5-11

52
 Chapter 5

07/12/2005 13:07 FAX 002

BIT 05: BW-SEND _____ OFF / OFF

BIT 06: CL-SEND _____ OFF / OFF
[6] BIT 07: PAF _____ OFF / OFF
BIT 08: BDSS _____ ON / OFF
BIT 09: BDL-IMAGE (600) _____ ON / OFF
BIT 10: COUNTER _____ ON / OFF
BIT 11: E-RDS _____ ON / OFF
BIT 12: BAR-DIMM _____ ON / OFF
BODY No. _____ MTExxxxx
ENGINE CODE _____ 20000016
SIZE TYPE _____ 0 : NONE
PRODUCT NAME _____ XXX
[7] TOTAL
TTL _____ 000688
COPY _____ 000685
FAX-PRT _____ 000000
PDL-PRT _____ 000000
RPT-PRT _____ 000000
READ ADJ PRM
026: _____ 0022
031: _____ 0000
032: _____ 0115
033: _____ 0032
034: _____ 0032
[8] 041: _____ 0000
042: _____ 0219
043: _____ 0075
044: _____ 0075
045: _____ 0075
046: _____ 0075
047: _____ 0032
048: _____ 0032
054: _____ 0032
213: _____ 0000
214: _____ 0000
215: _____ 0000
WRITE ADJ PRM
031: _____ 0050
032: _____ 0050
033: _____ 0050
034: _____ 0100
035: _____ 0100
036: _____ 0100
037: _____ 0100
[9] 038: _____ 0100
[10] 039: _____
_____
0100
OPTYION ROM 16MB
[11] USB MEMORY _____ OFF
DELIVERY FULL SENSOR 1 _____ ON
[12] DELIVERY FULL SENSOR 2 _____ OFF
USB SERIAL No. _____ 00XXXXXXXX
[13] MAC ADDRESS _____ 00 00 85 51 60 1C
BACKUP BATTERY _____ OFF
[14] LUGIA _____ 2
NUMBER OF LOGS
[15] ACTIVITY _____ 0
PRINTJOB ACCOUNT
COPY _____ 0
PDL PRINT _____ 0
RX PRINT _____ 0
_____
[16] REPORT
_____
0
JAM 3
SERVICE CALL _____ 0
ENVIROMENT _____ 0

F-5-12
[1] Type setting
[2] Print speed
[3] Memory size
[4] ROM version (MAIN/BOOT/LANG*1(language liblary/language file version)ECONT/option cassette/duplex unit/finisher)
[5] Activation function ON/OFF
[6] Soft ID information
[7] Total counter (TOTAL/COPY/FAX/PDL/REPORT record counts)
[8] Adjustment data (factory scan/record adjustment values)
[9] Option ROM availability
[10] USB memory availability
[11] No. 1/No. 2 paper full sensor sensor availability
[12] USB serial number
[13] MAC address
[14] Backup battery availability
[15] ROM version (Reader controller PCB)
[16] output the number of histories (communication history, copy/print/report/JOB history of the reception print, jam history, E code history, humidity log)
*1: only for the touch panel model

53
 Chapter 5

5.1.12.7 Service Label

0017-6191

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Enter the value given in the service label affixed to the rear cover when it has been replaced with a new one.

#PRINT>#PRINT NUMERIC #SCAN>#SCAN NUMERIC

FACTORY 1 2 3 FACTORY 1 2 3
031 50 026
032 50 031
033 50 032
034 100 033
035 100 034
036 100 041
037 100 042
038 100 043
039 100 044
045
046
047
#SCAN>#SCAN NUMERIC 048
054
213
214
body No:BFDxxxxx 215
F-5-13

5.1.12.8 e-RDS Communication Error Log List

0017-6192

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Description: Detailed information output when a communication error occurs

(For the output error message, see "RDS > Error Messages".)

5.1.12.9 Environmental Log Report

0017-8541

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

06/27/2007 13:07 FAX 0001

[1] ***********************************************
*** ENVIROMENTT LOG REPORT ***
***********************************************

SERIAL NO XXXxxxx
ENVIROMENT
No. DATE TIME D+Temp E+Hum F+Temp F+Temp
001 0616 0930 D030 E026 F180 F180
002 0616 1030 D028 E025 F181 F181

[2] [3] [4] [5] [6] [7] [8]

F-5-14

History description
Item Explanation
[1] Serial number Serial number of this machine
[2] Number The larger the number of a enviroment log data, the more recently it has occurred.
[3] Date Data acquisition day
[4] Time Data acquisition time
[5] Temperature (deg)
[6] Humidity (%)
[7] Fixing roller temperature 1
(deg)
[8] Fixing roller temperature 2
(deg)

54
 Chapter 5

5.1.13 Download (DOWNLOAD)

5.1.13.1 Download
0017-6182

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The following parts of this unit can be upgraded by executing download mode using the service support tool (SST) (for more information, see the "Upgrading"
section):

Main unit
- Flash ROM (system + boot) mounted on the image processor PCB
Accessory
- ROM mounted on the finisher controller PCB
- ROM mounted on the PCL board

5.1.14 Data Initialization Mode (CLEAR)

5.1.14.1 Clear
0017-6183

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Group Item Explanation

TEL & USER DATA Clears all user-registered and -set areas of telephone registration data and user data.
(Telephone registration refers to the registration of codes on one-touch dialing,
abbreviated dialing, and group dialing.)

SERVICE DATA Clears the system dump list, except for counters and clear dates.

COUNTER Clears the maintenance counter, parts counter and mode-specific counters.
Initializes the counter (numerator) in the system dump list.

TYPE Initializes user data and service data to suit specified destination settings.

SOFT-CNT Not used

HST ACTIVITY Initializes the activity report

ACCOUNT Clears print histories.

JAM Clears the jam history.

ERR Clear the error (error code) history.

ALARM Clears the alarm history.

ENVIROMENT Initializes the enviroment log data.

CARD Clears department management information held in the controller before the card
reader is demounted.

ERR E355 Not used

E719 Clears card reader errors.

PWD Clears the system administrator's password.

FILE SYSTEM*1 Delete unnecessary language files in the USB memory.

FORMAT*1 USB MEMORY Format the USB memory. (This mode is used when the USB memory error is damaged
and E744 occurs.)
LICENSE Not used
DRIVE
CA-KEY Initializes an installed CA certification.

ERDS-DAT The settings related to e-RDS are cleared to the factory settings.

ALL Clears user and service data (except for some scan parameters and print parameters),
and the counter setting/registration data in the system dump list, except for the print
count.

*1 Only for the touch panel model.

5.1.15 Error Display (ERROR DISPLAY)

5.1.15.1 Error Display

0017-8542

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

An error code is displayed when a service error has occurred. The E code is displayed in the upper step, and the detail code is displayed the bottom step.

55
 Chapter 5

5.1.16 Display of ROM Information (ROM)

5.1.16.1 ROM Display

0017-6184

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

The table below lists the items of ROM display mode that are supported.
T-5-31

Item Explanation

MAIN Displays the version number of the ROM (SYSTEM) mounted on the image
processor PCB.
MAIN2 Displays the version of the ROM (BOOT) mounted on the image processor
PCB.
ECONT Displays the version number of the ROM mounted on the DC controller PCB.

OPROM Displays the version number of the option ROM.

5.1.17 Test Mode (TEST MODE)

5.1.17.1 Outline
0017-6193

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Test mode must be executed by keeping track the flow of menu items appearing on the LCD. Menu items in test mode are organized into seven blocks as described
below. Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.
1. D-RAM test ((1) D-RAM)
Checks to see if data can be correctly written to and read from D-RAM.

2. Scan test ((2) SCAN TEST)

Used to adjust contact sensor output and the position at which a document fed from the ADF is scanned.

3. Print test ((3) PRINT TEST)

Used to generate service test patterns.
4. Modem test ((4) MODEM TEST)
Performs relay actuation, modem DTMF and tonal signal transmission/reception tests.
5. Aging test ((5) AGING TEST)
Not used.

6. Function test ((6) FUNCTION TEST)

Used to verify the operations of microswitches, sensors, speakers and ADF functions.

7. Roller cleaning mode ((0) ROLLER CLEAN)

Used to clean the delivery roller or ADF pickup roller by idling them.

5.1.17.2 Test Mode Menu List (LCD Type)

0017-6194

iR2025 / iR2030 / iR2018 / iR2022

Test mode menu list

To invoke test mode, follow these steps:

1) Enter service mode.

Press the operation panel user mode key, 2 key, 8 key and user mode key in this order.
2) Press the operation panel arrow keys to show "TEST MODE."
3) Press the OK key.
To exit test mode, press the user mode key to return to standby mode.
T-5-32

Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.

Group Subgroup Item 1 Item 2 Item 3 Explanation
TEST MODE [1] - [9], [#]
(1) DRAM [1] - [2] D-RAM data check
(1) D-RAM TEST Write/read check

(2) D-RAM TEST Read check

(2) SCAN TEST [1] - [8]
(1) SHADING Automatic gain adjustment
(3) SHEET POS ADJ CS position adjustment
(4) TRASH DETECT Dust detection

(5), (6), (9), (*) Not used

(3) PRINT TEST [1] - [9]

(1) Not used
(2) All-black output
(3) Not used
(4) Back belt output
(5), (6), (7), (8), (9), (*) Not used

56
 Chapter 5

Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.

Group Subgroup Item 1 Item 2 Item 3 Explanation
(4) MODEM TEST [1] - [9]
(1) RELAY TEST [1] - [2]
(1) RELAY TEST 1 NCU relay (and switch) ON/OFF test

(2) RELAY TEST 2 230 V common NCU test

(2) FREQ TEST [0] - [6] Frequency test
(0) FREQ TEST 462Hz
(1) FREQ TEST 1100Hz
(2) FREQ TEST 1300Hz
(3) FREQ TEST 1500Hz
(4) FREQ TSST 1650Hz
(5) FREQ TEST 1850Hz
(6) FREQ TEST 2100Hz
(4) G3 SIGNAL TX TEST [0] - [8] G3 signal transmission test
(0) G3 SIGNAL TX TEST 300bps
(1) G3 SIGNAL TX TEST 2400bps
(2) G3 SIGNAL TX TEST 4800bps
(3) G3 SIGNAL TX TEST 7200bps
(4) G3 SIGNAL TX TEST 9600bps
(5) G3 SIGNAL TX TEST TC7200bps
(6) G3 SIGNAL TX TEST TC9600bps
(7) G3 SIGNAL TX TEST 12000bps
(8) G3 SIGNAL TX TEST 14400bps
(5) DTMF TEST [0] - [9], * , # DTMF transmission test
(0) G3 SIGNAL TX TEST 300bps
(1) G3 SIGNAL TX TEST 2400bps
(2) G3 SIGNAL TX TEST 4800bps
(3) G3 SIGNAL TX TEST 7200bps
(4) G3 SIGNAL TX TEST 9600bps
(5) G3 SIGNAL TX TEST TC7200bps
(6) G3 SIGNAL TX TEST TC9600bps
(7) G3 SIGNAL TX TEST 12000bps
(8) G3 SIGNAL TX TEST 14400bps
(9) G3 SIGNAL TX TEST TC9600bps
(*) G3 SIGNAL TX TEST 12000bps
(#) G3 SIGNAL TX TEST 14400bps
(6) MODEM TEST Tonal sign reception test
(8) G3 V.34 Tx TEST V34 G3 signal transmission test
(9) Not used
(5) AGING TEST Not used
(6) FUNCTION TEST [1] - [9]

57
 Chapter 5

Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.

Group Subgroup Item 1 Item 2 Item 3 Explanation
(1) FUNCTION TEST G3 4800bps G3 4800 bps signal transmission test
(3) 6-3 SENSOR [1] - [6] Sensor checks
(1) SENSOR CHECK 0:NORMAL 1:LATCH
(0) SENSOR NORMAL [0] - [2]
(0) CAS 0 REG 0 DEL 0 MULTI 0
(1) TONER 0 FULL 0 2ND-DEL 0000
(2) OP1 0000 OP2 0000 OP3 0000 PATH
0000
(1) SENSOR
LATCH [0] -
[2]
(0) CAS 0 REG 0 DEL 0 MULTI 0
(1) TONER 0 FULL 0 2ND-DEL 0000
(2) OP1 0000 OP2 0000 OP3 0000 PATH
0000
(2) SWITCH CHECK [0] - [1]
(0) CAS 0000 LOCK 0000
(1) OP1 0000 OP2 0000 OP3 0000
(3) DS ON DES of HPS ON BCVS of
(4) REF xxx ANT xxx |ANT-REF| xxx
(5) BSCT on BDAC[ A3] BDSS3-0 [ of of of of ]
(6) NCR Sts: NCR xxxxx DPT MGN OK RDY 0101
(7) LAST of EXIT of REG of CVR of
(8) WID1 on WID2 on LEN1 on LEN2 on
(9) D+Temp xxxx E+Hum xxxx F+Temp xxxx xxxx
(4) ADF FEED TEST ADF delivery operation test
(5) BOOK FEED TEST Book copy operation test
(6) 6-6 SPEAKER FREQ:[1] VOL:[2] Speaker volume and buzzer frequency test
(7) Not used
(8) FUNCTION TEST LAMP TEST ALL Lamp test
(9) LINE TEST [1] - [3] Line signal reception test
(0) ROLLER CLEAN 0:PRT 1:ADF Printer and ADF roller cleaning
(0) PRT ROL CLEAN Press start key
(1) ADF ROL CLEAN Press start key

5.1.17.3 Test Mode Menu List (Touch Panel Type)

0017-6195

iR2022i / iR2018i

Test mode menu list

To invoke test mode, follow these steps:

1) Enter service mode.

Sequentially press the Additional functions key, 2 key, 8 key, and Additional functions key on the operation panel.
2) Press the arrow key on the touch panel to display "TEST MODE".
3) Press [OK].
T-5-33

Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.

Group Subgroup Item 1 Item 2 Item 3 Explanation
TEST MODE [1] - [9], [#]
(1) DRAM [1] - [2] D-RAM data check
(1) D-RAM TEST Write/read check

(2) D-RAM TEST Read check

(2) SCAN TEST [1] - [8]
(1) SHADING Automatic gain adjustment
(3) SHEET POS ADJ CS position adjustment
(4) TRASH DETECT Dust detection

(5), (6), (9), (*) Not used

(3) PRINT TEST [1] - [9]

(1) Not used
(2) All-black output
(3) Not used
(4) Back belt output
(5), (6), (7), (8), (9), (*) Not used
(4) MODEM TEST [1] - [9]

58
 Chapter 5

Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.

Group Subgroup Item 1 Item 2 Item 3 Explanation
(1) RELAY TEST [1] - [2]
(1) RELAY TEST 1 NCU relay (and switch) ON/OFF test

(2) RELAY TEST 2 230 V common NCU test

(2) FREQ TEST [0] - [6] Frequency test
(0) FREQ TEST 462Hz
(1) FREQ TEST 1100Hz
(2) FREQ TEST 1300Hz
(3) FREQ TEST 1500Hz
(4) FREQ TSST 1650Hz
(5) FREQ TEST 1850Hz
(6) FREQ TEST 2100Hz
(4) G3 SIGNAL TX TEST [0] - [8] G3 signal transmission test
(0) G3 SIGNAL TX TEST 300bps
(1) G3 SIGNAL TX TEST 2400bps
(2) G3 SIGNAL TX TEST 4800bps
(3) G3 SIGNAL TX TEST 7200bps
(4) G3 SIGNAL TX TEST 9600bps
(5) G3 SIGNAL TX TEST TC7200bps
(6) G3 SIGNAL TX TEST TC9600bps
(7) G3 SIGNAL TX TEST 12000bps
(8) G3 SIGNAL TX TEST 14400bps
(5) DTMF TEST [0] - [9], * , # DTMF transmission test
(0) G3 SIGNAL TX TEST 300bps
(1) G3 SIGNAL TX TEST 2400bps
(2) G3 SIGNAL TX TEST 4800bps
(3) G3 SIGNAL TX TEST 7200bps
(4) G3 SIGNAL TX TEST 9600bps
(5) G3 SIGNAL TX TEST TC7200bps
(6) G3 SIGNAL TX TEST TC9600bps
(7) G3 SIGNAL TX TEST 12000bps
(8) G3 SIGNAL TX TEST 14400bps
(9) G3 SIGNAL TX TEST TC9600bps
(*) G3 SIGNAL TX TEST 12000bps
(#) G3 SIGNAL TX TEST 14400bps
(6) MODEM TEST Tonal sign reception test
(8) G3 V.34 Tx TEST V34 G3 signal transmission test
(9) Not used
(5) AGING TEST Not used
(6) FUNCTION TEST [1] - [9]

59
 Chapter 5

Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.

Group Subgroup Item 1 Item 2 Item 3 Explanation
(1) FUNCTION TEST G3 4800bps G3 4800 bps signal transmission test
(3) 6-3 SENSOR [1] - [6] Sensor checks
(1) SENSOR CHECK 0:NORMAL 1:LATCH
(0) SENSOR NORMAL [0] - [2]
(0) CAS 0 REG 0 DEL 0 MULTI 0
(1) TONER 0 FULL 0 2ND-DEL 0000
(2) OP1 0000 OP2 0000 OP3 0000 PATH
0000
(1) SENSOR
LATCH [0] -
[2]
(0) CAS 0 REG 0 DEL 0 MULTI 0
(1) TONER 0 FULL 0 2ND-DEL 0000
(2) OP1 0000 OP2 0000 OP3 0000 PATH
0000
(2) SWITCH CHECK [0] - [1]
(0) CAS 0000 LOCK 0000
(1) OP1 0000 OP2 0000 OP3 0000
(3) DS ON DES of HPS ON BCVS of
(4) REF xxx ANT xxx |ANT-REF| xxx
(5) BSCT on BDAC[ A3] BDSS3-0 [ of of of of ]
(6) NCR Sts: NCR xxxxx DPT MGN OK RDY 0101
(7) LAST of EXIT of REG of CVR of
(8) WID1 on WID2 on LEN1 on LEN2 on
(9) D+Temp xxxx E+Hum xxxx F+Temp xxxx xxxx
(4) ADF FEED TEST ADF delivery operation test
(5) BOOK FEED TEST Book copy operation test
(6) 6-6 SPEAKER FREQ:[1] VOL:[2] Speaker volume and buzzer frequency test
(7) Not used
(8) FUNCTION TEST LAMP TEST ALL Lamp test
(9) LINE TEST [1] - [3] Line signal reception test
(0) ROLLER CLEAN 0:PRT 1:ADF Printer and ADF roller cleaning
(0) PRT ROL CLEAN Press start key
(1) ADF ROL CLEAN Press start key

5.1.17.4 D-RAM Test<(1) D-RAM TEST>

0017-6196

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

D-RAM Test((1) D-RAM)

Press the numeric keypad key 1 on the test mode menu to select the D-DRAM test.
Press numeric keypad keys 1 and 2 during the D-DRAM test to carry out the individual tests described below.

Numeric keypad key 1

Checks to see if data can be correctly written to and read from all areas of D-RAM (SDRAM). If an error occurs making this check, the test is aborted, with an
error appearing on the touch panel (LCD).

Numeric keypad key 2

Checks to see if data can be correctly read from all areas of D-RAM (SDRAM). If an error occurs making this check, the test is aborted, with an error appearing
on the touch panel (LCD).

D-RAM TEST 30208KB

[1] - [2]

D-RAM TEST 30208KB D-RAM TEST 30208KB

complete (no error)

WRT= 33CC RD= 33EC

ADR= BF840201

D-RAM TEST 30208KB

D-RAM TEST 30208KB

complete (error)

F-5-15

60
 Chapter 5

5.1.17.5 Scan Test ((2) SCAN TEST)

0017-6197

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Scan test ((2) SCAN TEST)

Press the numeric keypad key 2 on the test mode menu to select the CCD test.
Press numeric keypad keys 1, 3 and 4 during the CCD test to carry out the individual tests described below.

Numeric keypad key 1

Corrects the LED output of the contact sensor and sets its parameters automatically. (AGC adjustment)

Numeric keypad key 3

Adjusts the document scan position (only on models with the ADF feature installed). Adjusts the position of the contact sensor for scanning documents fed from
the ADF automatically.

Numeric keypad key 4

Detects trash at reader scan positions A/B/C.
Pos A: Reference read position
Pos B: About 0.5 mm inside of the roller from the reference position
Pos C: About 1.0 mm inside of the roller from the reference position

5.1.17.6 Print Test ((3) PRINT TEST)

0017-6198

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Print test ((3) PRINT TEST)

Press the numeric keypad key 3 on the test mode menu to select the print test.
Press numeric keypad keys 2 and 4 during the print test to generate test patterns as described below. Two kinds of service test patterns are available. Other test
patterns are reserved for factory/development purposes.

Numeric keypad key 2

(2) BLACK: All-black output
Numeric keypad key 4
(4) ENDURANCE: Black belt output

To cancel test printing, press the stop key.

Use it to make sure that the print Use it to make sure that the print
pattern does not have white lines pattern does not have contraction/
or uneven image. elongation of an image or dirt/black
line.s
F-5-16

5.1.17.7 Modem Test ((4) MODEM TEST)

0017-6199

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

MODEM test((4) MODEM TEST)

These tests test modem and NCU transmission and reception. The modem tests check whether signals are sent correctly from the modem by comparing the sound
of the signals from the speaker with the sounds from a normal modem.
End this test by pressing the Stop key.

Keypad Type Description

1 Relay test Use it to turn on/off a selected relay to execute a switch-over test

2 Frequency test The modem sends tonal signals from the modular jack and the speaker.

4 G3 signal transmission test The modem sends G3 signals from the modular jack and the speaker.

5 DTMF signal reception test Use it to generate the DTMF signal coming from the modem using the
telephone line terminal and the speaker.
6 Tonal signal reception test Use it to monitor a specific frequency and the DTMF signal received from
the telephone line terminal by causing them to be indicated on the LCD (i.e.,
the presence/absence as detected). The reception signal is generated by the
speaker.
8 V.34 G3 signal transmission test The modem sends V.34 G3 signals from the modular jack and the speaker.

Relay Test

61
 Chapter 5

Press '1'or '2' on the keypad on the Modem test menu to select relay test mode. Use the keypad to operate the various relays of the NCU. '2' on the keypad is used
for 230V machine.
Numeric keypad key 1
The input key and relay are shown below:

[1] [2]

RELAY TEST1 OFF OFF

OFF OFF OFF OFF

[3] [4] [5] [6]

F-5-17
Numeric keypad key 2
The input key and relay are shown below:

[1] [2]

RELAY TEST2 OFF OFF

OFF OFF OFF OFF OFF

[3] [4] [5] [6] [7]

F-5-18

The touch panel (LCD) is turned on or off in relation to the transmission of the relay operation signal as is operated on the keypad; for this reason, you cannot use
the touch panel (LCD) to check a fault on a single relay.

Frequency Test
A press on '2' on the keypad from the MODEM test menu selects the frequency test.
In this test, signals of the following frequencies from the modem are transmitted using the telephone line terminal and the speaker. To select a different frequency,
use the keypad.

Keypad Frequency

1 462Hz

2 1100Hz

3 1300Hz

4 1500Hz

5 1650Hz

6 1850Hz

7 2100Hz

MEMO:
The frequency and the output level of individual frequencies are in keeping with the output level set in service mode.

G3 Signal Transmission Test

A press on '4' on the keypad from the MODEM test menu selects the G3 signal transmission test. In this test, the following G3 signals from the modem are trans-
mitted using the telephone line terminal and the speaker. To select a different transmission speed, use the keypad.

Keypad Transmission speed

0 300bps

1 2400bps

2 4800bps

3 7200bps

4 9600bps

5 TC7200bps

6 TC9600bps

7 12000bps

8 14400bps

62
 Chapter 5

MEMO:
The output level of individual signals is in keeping with the setting made in service mode.

DTMF Signal Transmission Test

A press on '5' on the MODEM test menu selects the DTMF signal transmission test. In the test, the following DTMF signals from the modem are transmitted using
the telephone line terminal and the speaker. The number pressed on the keypad selects a specific DTMF signal.

MEMO:
The output level of individual signals is in keeping with the setting made in service mode.

Tonal/DTMF Signal Reception Test

A press on '6' on the keypad from the MODEM test menu selects the tonal signal/DTMF signal reception 0 test. In this signal, the tonal signal/DTMF signal received
from the telephone line terminal can be checked to find out if it was detected by the modem.

Tonal signal reception test

MODEM TEST
OFF OFF OFF

OFF OFF OFF

changes from '0' to '1' in response to detection of a signal of 462 25 Hz.
changes from '0' to '1' in response to detection of a signal of 1100 30 Hz.
changes from '0' to '1' in response to detection of a signal of 2100 25 Hz.

DTMF signal reception test

MODEM TEST
OFF OFF OFF 5
The received DTMF signals are indicated starting
from the right using the 2nd character of the display.
F-5-19
V.34 G3 Signal Transmission Test
A press on '8' on the keypad from the MODEM test menu selectes the V.34 G3 signal transmission test. The V.34 G3 signals below are sent from the modem using
the modular jack and the speaker by pressing the start key. The Baud rate can be changed with the keypad, and the Speed can be changed with the left/right arrow
key.

Keypad Baud rate

0 3429baud

1 3200baud

2 3000baud

3 2800baud

4 2743baud

5 2400baud

Left/right arrow key Transmission speed

2400bps

4800bps

7200bps

9600bps

< 12000bps

14400bps

16800bps

19200bps

21600bps

> 24000bps

26400bps

28800bps

31200bps

33600bps

63
 Chapter 5

5.1.17.8 Function Test ((6) FUNCTION TEST)

0017-6203

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Function test ((6) FUNCTION TEST)

Press the numeric keypad key 6 on the test mode menu to select the function test.
Press numeric keypad keys 1 and 3 to 9 during the function test to enter the menus listed below.
T-5-34

Keypad Item Explanation

1 G3 signal transmission test Transmits 4800-bps G3 signals to a telephone line and

speaker.
2 Not used

3 Sensor test Sensor actuation test

4 ADF test ADF operation test

5 Book test Host machine operation test

6 Speaker test Speaker operation test

7 Not used

8 Lamp test Contact sensor illumination test

9 Line signal reception test NCU board signal sensor and frequency counter operation test

G3 signal transmission test (6-1: G3 480 bps Tx)

Press numeric keypad key 1 on the FUNCTION TEST menu to select the G3 signal transmission test. This test transmits 4800-bps G3 signals from the telephone
line connection terminal and speaker.
Sensor test (6-3: SENSOR)
This mode is used to verify the status of the unit sensors from the touch panel (LCD) indications. Press numeric keypad key 3 on the FUNCTION TEST menu to
select the sensor test. The touch panel (LCD) indications change as the associated sensors turn on and off.

64
 Chapter 5

6-3:SENOR
[1] - [6]

Press numeric keypad key 1. Press numeric keypad key 0. Press numeric keypad key 0.

SENSOR CHECK SENSOR NORMAL CAS 0 REG 0

0:NORMAL 1:LATCH [0] - [2] DEL 0 0 MULTI 0

Select a sensor mode. CAS:Cassette 1 paper sensor (SR204): 0/Document presence, 1/Document absence
0: NORMAL REG:Registration sensor (SR209): 0/Document presence, 1/Document absence
Indications change from 0 Press numeric keypad key 1. DEL 0 0:
to 1 as the sensors turn on. Fixing delivery sensor (SR202): 1/ Document presence, 0/ Document absence
Indications change from 1 SENSOR LATCH No.1 delivery sensor (SR203): 1/ Document presence, 0/ Document absence
to 0 as the sensors turn off. [0] - [2] MULTI:Manual paper sensor (SR208): 0/Document presence, 1/Document absence
1: LATCH
Indications change from 0
to 1 as the sensors turn on.
Indications do not change back Press numeric keypad key 1.
from 1 to 0 once the sensors turn
on from the off state. TONER 0 FULL 0
2ND-DEL 0 0

TONER:Waste toner full sensor (SR206): 0/Full, 1/Available

FULL:No. 1 paper full sensor (SR207): 0/Document presence, 1/Document absence
2ND-DEL 0 0:
No. 2 paper full sensor (SR1102): 0/Document presence, 1/Document absence
No. 2 delivery sensor (SR1101): 0/Document presence, 1/Document absence

OP1 0 0 OP2 0 0
OP3 0 0 PATH 0 0

OP1 0 0:
Cassette 2 retry sensor (SR6): 0/Document presence, 1/Document absenc
Cassette 2 paper sensor (SR5): 0/Document presence, 1/Document absence
OP2 0 0:
Cassette 3 retry sensor (SR6): 0/Document presence, 1/Document absence
Cassette 3 paper sensor (SR5): 0/Document presence, 1/Document absence
OP3 0 0:
Cassette 4 retry sensor (SR6): 0/Document presence, 1/Document absence
Cassette 4 paper sensor (SR5): 0/Document presence, 1/Document absence
PATH 0 0:
Duplex paper sensor 1 (SR1002): 0/Document presence, 1/Document absence
Duplex paper sensor 2 (SR1002): 0/Document presence, 1/Document absence

Press numeric keypad key 2 Press numeric keypad key 0.

SWITCH CHECK CAS 0000

[0] - [1] LOCK 0

CAS 0000:Cassette 1 size detection switch

Cassette size switch (PSIZE3): 1/Pressed, 0/Not pressed
Cassette size switch (PSIZE4): 1/Pressed, 0/Not pressed
Cassette size switch (PSIZE2): 1/Pressed, 0/Not pressed
Cassette size switch (PSIZE1): 1/Pressed, 0/Not pressed
LOCK: Cover switch (SW2 and SW3): 1/Cover open, 0/Cover closed

Press numeric keypad key 1.

OP1 0000 OP2 0000

OP3 0000

OP1: Cassette 2 size detection switch

OP2: Cassette 3 size detection switch
OP3: Cassette 4 size detection switch
OPX 0000: (X = 1, 2, 3 option cassette level)
Cassette size switch (PSIZE3): 1/Pressed, 0/Not pressed
Cassette size switch (PSIZE4): 1/Pressed, 0/Not pressed
Cassette size switch (PSIZE2): 1/Pressed, 0/Not pressed
Cassette size switch (PSIZE1): 1/Pressed, 0/Not pressed

Press numeric keypad key 3

DS ON DES of HPS ON
BCVS of

DS: ADF document sensor (P111): On/Paper presence, Of/Paper absence

DES Read sensor (P17): On/Paper presence, Of/Paper absence
HPS: CISHP sensor (P401): On/Paper presence, Of/Paper absence
BCVS: Document platen cover open/close sensor (front) (SR403): On/Cover open, Of/Cover closed

F-5-20

65
 Chapter 5

Press numeric keypad key 4.

REF xxx ANT xxx

|ANT - LEF| xxx

REF: Toner reference voltage (A/D value)

ANT: Toner antenna voltage (A/D value)
ANT - LEF: Differential voltage (A/D value)

Press numeric keypad key 5.

BSCT on BDOC[A3 ]
BDSS3-0 [of of of of]

BCST: Document platen cover sensor (SR402): On/Cover open, Of/Cover closed
BDOC: Document size: Paper size indicated in a mix of document size sensors
BDSS3-0 [of of of of]:
Document size sensor (SR404 or SR405): On/Document presence, Of/Document absence
Document size sensor (SR403): On/Document presence, Of/Document absence
Document size sensor (SR401): On/Document presence, Of/Document absence
Document size sensor (SR402): On/Document presence, Of/Document absence
Press numeric
keypad key 6. [1]

NCR Sts : 12345678

DPT MGN OK RDY 1234

[2] [3] [4] [5] [6]

[1] Card reader and card availability indication [4] Can status
Card available: Eight-digit card ID OK: Normal scan
No card: Card None ERR: Scan error
No card reader available: NCR None NG: Nonstandard error
(No indication): No card

[2] Card type and card reader status indication [5] Equipment status
DPT: Department card IN: Initialization in progress
PRC: Unit pricing card RDY: Ready
MAX: Upper limit setting card
ERS: Erased card [6] Card reader version indication
SRV: Service card Four-digit number
(No indication): No card

[3] Card type

MGN: Magnetic card
OPT: Optical card
Press numeric
keypad key 7.
LAST of EXIT of
REG of CVR of

LAST: Last document detection sensor(PI3): On/Paper presence, Of/Paper absence*1

EXIT: Delivery reversal sensor(PI6): On/Paper presence, Of/Paper absence*1
REG: Registration paper sensor(PI8): On/Paper presence, Of/Paper absence*1
CVR: Cover open/close sensor (PI10): On/Paper presence, Of/Paper absence*1
*1:Only if equipped with ADF functions.
Press numeric
keypad key 8.
WID1 of WID2 of
LEN1 of LEN2 of

WID1: Document width sensor 1 (PI2):On/Paper presence, Of/Paper absence*1

WID2: Document width sensor 2 (PI1): On/Paper presence, Of/Paper absence*1
LEN1: Document length sensor 1(PI4):On/Paper presence, Of/Paper absence*1
LEN2: Document length sensor 2(PI5): On/Paper presence, Of/Paper absence*1
*1:Only if equipped with ADF functions.
Press numeric
keypad key 9.
D+Temp xxxx E+Hum xxxx
F+Temp

D+Temp: In-machine temperature (Unit: deg C)

E+Hum: In-machine humidity (Unit: %RH)
F+Temp: Fixing roller temperature (Unit: deg C)
F-5-21
ADF feed test (6-4: ADF FEED TEST)
ADF operation verification mode. Press numeric keypad key 4 on the FUNCTION TEST menu to select the ADF feed test. Place a document on the document
platen and press the start key to transfer the document at the speed matched to the scan resolution setting. In this test, enter a transfer speed between 500 and 2000
(mm/s) from the numeric keypad and verify the transfer speed. Select between the ON and OFF states with the left and right cursor keys to select between single-
sided document feed (OFF) and double-sided document feed (ON).

Book feed test (6-5: BOOK FEED TEST)

Performs a book feed operation with a specified magnification and in a specified size.
Speaker test (6-6: SPEAKER)
Speaker operation verification mode. Press numeric keypad key 6 on the FUNCTION TEST menu to select the speaker test. In this test, the speaker generates tonal
signals at 100 Hz intervals, from 200 Hz to 5 kHz, in varying sound volumes. Signal output from the speaker is thus verified.

66
 Chapter 5

6-6: SPEAKER
FREQ [1] VOL [2]

Press numeric Press numeric

keypad key 1. keypad key 2.

SPEAKER SPEAKER
FREQ TEST VOL[*] :MIN [#]:MAX

Press the start key Signal tone volume adjustment.

to change the * denotes the minimum, #, the maximum.
transmission frequency The volume is adjustable level by level
using the start key.

F-5-22
Lamp test (6-8: LAMP TEST)
Press numeric keypad key 8 on the FACULTY menu to select the scan lamp illumination mode. The test checks to see if the scan lamp is on or not.
Numeric keypad key 1 selects LAMP TEST ALL. Press the start key to turn on all scan lamps. LAMP TEST AGC is not used.
Line signal reception test (6-9 LINE DETECT)
Press numeric keypad key 9 on the FACULTY menu to select the line signal reception test. In this test, verify the successful operations of the NCU signal sensor
and the frequency counter. Menu 1 detects the CI state, while menu 3 detects the CNG signal.
Test menu 1
Press numeric keypad key 1 on the LINE DETECT menu to select test menu 1. When CI is detected on the telephone line connection terminal, the touch
panel (LCD) display changes from OFF to ON, indicating the received frequency. The touch panel (LCD) also displays the on-hook or off-hook state of an
external telephone set as detected. The touch panel (LCD) displays, from left to right, CI, CI frequency, hook port and FC with indications of 1:ON and
0:OFF.
Test menu 2
Press numeric keypad key 2 on the LINE DETECT menu to select test menu 2. When the CNG signal is detected on the telephone line connection terminal,
the touch panel (LCD) display changes from OFF to ON, indicating the received frequency. The touch panel (LCD) displays the status of CML, CNG and
FED detection, from left to right, with ON/OFF indications. Numeric keypad key 2 turns on the CML relay to detect CNG.
Test menu 3
Press numeric keypad key 3 on the LINE DETECT menu to select test menu 3. When the CNG signal is detected on the telephone line connection terminal,
the touch panel (LCD) display changes from OFF to ON, indicating the received frequency. The touch panel (LCD) displays the status of CML, CNG and
FED detection, from left to right, with ON/OFF indications. Numeric keypad key 3 turns off the CML relay to detect CNG.

5.1.17.9 Roller cleaning mode ((0) ROLLER CLEAN)

0017-6204

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Roller cleaning mode ((0) ROLLER CLEAN)

Press numeric keypad key 0 in test mode to select roller cleaning mode. Press numeric keypad keys 1 and 2 during this test to enter the following menus:
Numeric keypad key 1
Press the start key clean the ADF pickup/feed rollers by idling.

Press the stop key to exit this mode.

Numeric keypad key 2
Press the start key clean the unit transfer rollers by idling.
Press the stop key to exit this mode.

67
 Chapter 6

Chapter 6 Outline of Components

6.1 Clutch/Solenoid

6.1.1 List of Clutches/Solenoids

0017-5994

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

<Reader Unit>
The reader unit has no clutch/solenoid.
<Printer Unit>

Symbol Name Function

CL201 Manual pickup clutch Drives the manual pickup roller.

CL202 Cassette feed clutch Drives the cassette feed roller.

CL203 Registration clutch Drives the registration clutch.

SL201 Manual pickup solenoid Drives the manual pickup roller.

SL202 Cassette 1 pickup solenoid Drives the cassette 1 pickup roller.

Symbol Part No. DC controller PCB

CL201 FK2-1070 J219
CL202 FK2-5367 J211
CL203 FK2-5350 J210
SL201 FK2-1072 J219
SL202 FK2-1082 J209

CL203

CL201

SL201

SL202

CL202
F-6-1

6.2 Motor

6.2.1 List of Motors

0017-5996

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

69
 Chapter 6

<Reader Unit>

Symbol Name Function

M401 Reader motor Drives the carriage.

Symbol Part No. Reader controller PCB Error

M401 FK2-1066 J409

M401

F-6-2
<Printer Unit>

Symbol Name Function

Fixing motor Drives the fixing unit.
M201

M203 Polygon motor Drives the laser scanner.

M204 Main motor Drives the main parts of the printer.

Symbol Part No. DC controller PCB Error

M201 FK2-5348 J202 E007, E808

M203 Scanner unit J205
FM3-3695
M204 FK2-5347 J208 E010

M201

M203

M204

F-6-3

70
 Chapter 6

6.3 Fan

6.3.1 List of Fans

0017-5997

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

<Reader Unit>
The reader unit has no fan.
<Printer Unit>
T-6-1

Symbol Name Function

FM1 Heat discharge fan Cools fixing unit.

Symbol Part No. DC controller PCB Error

FM1 FK2-5368 J219 E805

FM1

F-6-4

6.4 Sensor

6.4.1 List of Sensors

0017-5998

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

71
 Chapter 6

<Reader Unit>
T-6-2

Symbol Name Function

SR401 CIS HP sensor Detects the CIS home position.

SR402 Copyboard cover open/closed sensor (rear) Detects opening/closing of the copyboard cover.

SR403 Copyboard cover open/closed sensor (front) Detects opening/closing of the copyboard cover.

SR404 Original sensor 1 Detects the original size (AB or INCH/AB).

SR405 Original sensor 2 Detects the original size (AB or INCH/AB).

SR406 Original sensor 3 Detects the original size (all destinations).

SR407 Original sensor 4 Detects the original size (AB or INCH/AB).

SR408 Original sensor 5 Detects the original size (INCH/A).

SR409 Original sensor 5 Detects the original size (INCH).

SR410 Original sensor 5 Detects the original size (A).

CIS1 CIS Reads the original.

T-6-3

Symbol Part No. Reader controller PCB Jam code

SR401 WG8-5696 J406
SR402 WG8-5696 J405
SR403 WG8-5696 J405 000f
SR404 FH7-7569 J407
SR405 FH7-7569 J407
SR406 FH7-7569 J413
SR407 FH7-7569 J413
SR408 FH7-7569 J1926
SR409 FH7-7569 J1927
SR410 FH7-7569 J1928

CIS1 FM2-3369 J408

SR407 SR408
SR406

SR403 SR404/SR409

SR402

SR405/SR410

SR401

CIS1
F-6-5

72
 Chapter 6

<Printer Unit>
T-6-4

Symbol Name Function

SR101 Fixing film speed sensor Detects the fixing film speed.

SR202 Fixing delivery sensor Detects fixing delivery.

SR203 No.1 delivery sensor Detects delivery.

SR204 Cassette 1 paper sensor Detects presence/absence of cassette 1 paper.

SR206 Waste toner full detection sensor Detects the waste toner full status.

SR207 No.1 paper full sensor Detects the No.1 paper full status.

SR208 Manual paper sensor Detects presence/absence of manually fed paper.

SR209 Registration sensor Detects registration paper.

SR210 Timing sensor Detects refeeding.

[1] Humidity sensor PCB Detects humidity.

TH1 Fixing main thermistor Detects the fixing heater temperature.

TH2 Fixing sub thermistor Detects the fixing heater temperature.
TP1 Thermo switch Cuts off the heater power supply line when an abnormal temperature is
detected.

73
 Chapter 6

T-6-5

Symbol Part No. DC controller PCB Jam code

SR201 FG3-3501 J217

SR202 WG8-5696 J217 010c, 0210, 0214, 1118
SR203 WG8-5696 J221 010c, 0210, 0214, 1118
SR204 WG8-5696 J213
SR206 WG8-5696 J216
SR207 WG8-5696 J201
SR208 WG8-5696 J219
SR209 WG8-5696 J212 0104, 0208, 010c, 0214, 1118
SR210 WG8-5696 J213
[1] WP2-5254 J222

T-6-6

Symbol Part No. DC controller PCB Power supply PCB

TH1,TH2 Fixing film unit J217
FM3-3654(120V)
FM3-3653(230V)
TP1 J13

SR207

SR203 [1]

TH1, TH2, TP1

SR208
SR101
SR210
SR204
SR209 SR202 SR206
F-6-6

6.5 Switch

6.5.1 List of Switches

0017-5999

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

74
 Chapter 6

<Reader Unit>
The reader unit has no switch.
<Printer Unit>

Symbol Name Function

SW2 Front cover switch Detects opening/closing of the front cover.

Left door switch Detects opening/closing of the left door.

SW3

SW4 Cassette 1 size detection switch Detects the cassette 1 paper size.

Symbol Part No. DC controller PCB Power supply PCB

SW2 FM2-4433 J12

SW3 FM2-4020 J12

SW4 WC2-5332 J213

SW2

SW3 SW4

F-6-7

6.6 Lamps, Heaters, and Others

6.6.1 List of Lamps, Heaters, and Others

0017-6000

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

75
 Chapter 6

<Reader Unit>

Symbol Name Part No. Function

Prevents dew condensation on the ADF
H3 Reader heater (left) NPN
reading glass.
Prevents dew condensation on the
H4 Reader heater (right) NPN
copyboard glass.

H4

H3

F-6-8
<Printer unit>

Symbol Name Function

H1 Fixing main heater Used as the main heater for fixing.
H2 Fixing sub heater Used as the sub heater for fixing.
H6 Cassette heater Prevents paper in the cassette from absorbing moisture.

VA1 Varistor Used as a varistor.

SP1 Speaker Used as a speaker (for fax unit).

76
 Chapter 6

Symbol Part No.

Fixing film unit

FM3-3654(120V)
FM3-3653(230V)

H1,H2

H6 FM3-3712(100V)
FM3-3714(230V)

Symbol Part No. Modem PCB

VA1 FH5-3543

SP1 FK2-1265 J1203

H1, H2

VA1 SP1
H6

F-6-9

6.7 PCBs

6.7.1 List of PCBs

0017-6001

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

77
 Chapter 6

<Reader Unit>

Symbol Name Part No. Function

Reader controller PCB FM2-4792 controls the reader unit/ADF
[1]

[1]

F-6-10
<Printer unit>

Symbol Name Part No. Function

Laser driver PCB Scanner unit controls the laser unit drive
[1]
FM3-3695
BD PCB generates the BD signal
[2]

Image processor PCB FM3-3320(LCD type) processes output image data for the printer unit
[3]
FM3-3319(Touch panel type)
128MB RAM FM3-3324 temporarily retains image data
[4]

LAN PCB FM3-3323 network interface/printer function control

[5]

Seriar interface PCB FM2-4062(SERIAL INTERFACE-A2) coin vendor interface

[6]
FM3-3326(Serial Interface Kit-H1)
Modem PCB FM3-3321 control the fax
[7]

PCL PCB FM3-3328(LCD type) PCL function control

[8]
FM3-3329(Touch panel type)
NCU PCB FM3-3332 controls the line switching operation
[9]

modular PCB FM2-4777(120V) fax line interface

[10]
FM2-4772(230V)
DC controller PCB FM3-2992:120V/18cpm controls the printer unit/option
FM3-2993:230V/18cpm
FM3-2994:120V/22cpm
FM3-2995:230V/22cpm
[11] FM3-2996:120V/25cpm
FM3-2997:230V/25cpm
FM3-2998:120V/30cpm
FM3-2999:230V/30cpm

Option power supply PCB FK2-1085(120V) Option power supply

[12] FK2-1086(230V)

Heater PCB FM2-4021 heater power switch

[13]

Operation panel PCB Operation panel unit controls the operation panel
FK2-5340(LCD type: USA/others)
FK2-5341(LCD type: Europe)
[14] FK2-5342(LCD type: China)
FK2-5343(LCD type: Taiwan)
FK2-5344(LCD type: Korea)
FM3-3620(Touch panel type)

Power supply PCB FK2-5355(120V) printer power supply

[15]
FK2-5356(230V)
HVT PCB FM3-2987 high-voltage power supply
[16]

FAX PANEL PCB FM3-2991 control the fax panel

[17]

78
 [3]
[2] [4]
[5]

[6]

[1]

[7]

[8]

[9]

[10]
[13]
[12] [11]
F-6-11

[14]

[17]
[15]

[16]
F-6-12
 Chapter 7

Chapter 7 System Construction

7.1 System Construction

7.1.1 Pickup/Delivery/Original Handling Accessories System Configuration (iR2018)

0017-9181

iR2018

79
 Chapter 7

The configuration is as shown in the following figure:

[4]

[3]
[2]

[1]

[5]
[11]
[12]

[10]

[6]

[9]

[7]

[6]
[7]

[8]

[8]

F-7-1

[1] DADF-P2 [7] Cassette Feeding Module-Q1

[2] Platen Cover Type J (*1) [8] Cassette Heater Attachment Kit-E1

[3] Finisher-U2 [9] Duplex Unit-B1 (*1)

[4] Additional Finisher Tray-C1 [10] Power Supply Kit-Q1

[5] Inner 2-way Tray-E2 [11] Document Tray-J1

[6] Cassette Feeding Module-P1 [12] Card Reader-E1

*1. There are models of the standard equipment.

80
 Chapter 7

7.1.2 Pickup/Delivery/Original Handling Accessories System Configuration (iR2018i)

0017-9182

iR2018i

The configuration is as shown in the following figure:

[2]

[1]

[3]
[9]
[10]

[8]

[4]

[7]

[5]

[5]

[4]

[6]
[6]

F-7-2

[6] Cassette Heater Attachment Kit-E1

[1] Finisher-U2
[7] Duplex Unit-B1 (*1)
[2] Additional Finisher Tray-C1
[8] Power Supply Kit-Q1
[3] Inner 2-way Tray-E2
[9] Document Tray-J1
[4] Cassette Feeding Module-P1
[10] Card Reader-E1
[5] Cassette Feeding Module-Q1

*1. There are models of the standard equipment.

81
 Chapter 7

7.1.3 Pickup/ Delivery /Original Handling Accessories System Configuration (iR2022/iR2022N/iR2025/iR2030)

0017-9183

iR2025 / iR2030 / iR2022

The configuration is as shown in the following figure:

[2] [4]

[1]
[3]

[10]

[11]

[5]
[9]

[8]

[6]

[7] [7]
F-7-3

[7] Cassette Heater Attachment Kit-E1

[1] DADF-P2 (*1)
[8] Duplex Unit-B1 (*1)
[2] Platen Cover Type J (*1)
[9] Power Supply Kit-Q1
[3] Finisher-U2
[10] Document Tray-J1
[4] Additional Finisher Tray-C1
[11] Card Reader-E1
[5] Inner 2-way Tray-E2

[6] Cassette Feeding Module-Q1

*1. There are models of the standard equipment.

82
 Chapter 7

7.1.4 Pickup/Delivery/Original Handling Accessories System Configuration (iR2022i/iR2022K/iR2025i/iR2030i)

0017-9187

iR2022i / iR2025 / iR2030

The configuration is as shown in the following figure:

[2]

[1]

[3]
[8]

[9]

[7]

[6]
[4]

[5]
[5]
F-7-4

[6] Duplex Unit-B1 (*1)

[1] Finisher-U2
[7] Power Supply Kit-Q1
[2] Additional Finisher Tray-C1
[8] Document Tray-J1
[3] Inner 2-way Tray-E2
[9] Card Reader-E1
[4] Cassette Feeding Module-Q1

[5] Cassette Heater Attachment Kit-E1

*1. There are models of the standard equipment.

83
 Chapter 7

7.1.5 Reader Heater/Cassette Heater System Configuration (iR2018/iR2022/iR2022N)

0017-9191

iR2018 / iR2022

The configuration is as shown in the following figure:

[1]

[3] [2]
F-7-5

[1] Reader Heater (*1)

[2] Cassette Heater (*1)
[3] Heater PCB

*1: To operate the heaters, a heater PCB is required. These parts are supplied as service parts, not the standard items.

84
 Chapter 7

7.1.6 Reader Heater/Cassette Heater System Configuration (iR2018i)

0017-9193

iR2018i

The configuration is as shown in the following figure:

[1]

[3] [2]
F-7-6

[1] Reader Heater (*1)

[2] Cassette Heater (*1)
[3] Heater PCB

*1: To operate the heaters, a heater PCB is required. These parts are supplied as service parts, not the standard items.

85
 Chapter 7

7.1.7 Reader Heater/Cassette Heater System Configuration (iR2022K/iR2022i/iR2025/iR2025i/iR2030/iR2030i)

0017-9194

iR2022i / iR2025 / iR2030

The configuration is as shown in the following figure:

[1]

[3] [2]

F-7-7

[1] Reader Heater (*1)

[2] Cassette Heater (*1)
[3] Heater PCB

*1: To operate the heaters, a heater PCB is required. These parts are supplied as service parts, not the standard items.

86
 Chapter 7

7.1.8 Printing/Transmitting Accessories System Configuration (iR2018/ir2022/iR2022N)

0017-9196

iR2018 / iR2022

The configuration is as shown in the following figure:

[1]

[2]

[3]
[4]

[5]

[8]

[7]
[6]
F-7-8

FAX Panel-A1 (*2) [5] PCL Printer Kit-V1/W1 (*3)

[1]
[2] Barcode Printing Kit-B1 (license certificate) [6] SUPER G3 FAX BD-AA1 (*2)

UFRII LT P.Kit-V1 (*1) [7] iR128MB EXP.RAM-E1

[3]
Serial Interface Board-A2 [8] Serial Interface Kit-H1
[4]

*1. There are models of the standard equipment.

*2: To make the FAX feature effective, a FAX panel and a super G3 FAX board are required.
*3: The PCL printer kit contains a 128MB expansion RAM.

87
 Chapter 7

7.1.9 Printing/Transmitting Accessories System Configuration (iR2018i/iR2022i/iR2022K/iR2025/iR2025i/iR2030/iR2030i)

0017-9197

iR2022i / iR2025 / iR2030 / iR2018i

The configuration is as shown in the following figure:

[1]

[2]

[3]

[7]

[4]

[5]

[6]
F-7-9

[5] Color SEND Kit-L1 (license certificate) (*1)

[1] UFRII LT P.Kit-V1 (*1)
[6] Barcorde Printing Kit-B1 (license certificate)
[2] Serial Interface Board-A2
[7] Serial Interface Kit-H1
[3] PCL Printer Kit-V1/W1 (*1)

[4] SUPER G3 FAX BD-AA1 (*1)

*1. There are models of the standard equipment.

88
 Chapter 7

7.1.10 Functions of the Printing/Transmission Functions (iR2018/iR2022/iR2022N)

0017-5905

iR2018 / iR2022

The following is a brief explanation of the functions expected of the accessories; for details, see the chapters that follow:

UFR II printer function (Resolution: 600dpi) ==> UFRII LT Printer Kit-V1

UFR II printer function (Resolution: 1200dpi) ==> UFRII LT Printer Kit-V1

iR 128MB Expansion RAM-E1

PCL print function ==> PCL Printer Kit-V1

FAX function ==> Super G3 FAX Board-AA1

FAX Panel-A1

Coin vender function ==> Serial Interface board-A2

Coin vender function (RS232C type) ==> Serial Interface kit-H1

Barcode print function ==> Barcode Printing Kit-B1

7.1.11 Functions of the Printing/Transmission Functions (iR2018i/iR2022i/iR2022K/iR2025/iR2025i/IR2030/iR2030i)

0017-5906

iR2022i / iR2025 / iR2030 / iR2018i

The following is a brief explanation of the functions expected of the accessories; for details, see the chapters that follow:
Color Send Kit-L1
UFR II printer function (Resolution: 1200dpi) ==> UFRII LT Printer Kit-V1

PCL print function ==> PCL Printer Kit-W1

FAX function ==> Super G3 FAX Board-AA1

Coin vender function ==> Serial Interface board-A2

Coin vender function (RS232C type) ==> Serial Interface kit-H1

Color SEND function ==> Color Send Kit-L1

Barcode print function ==> Barcode Printing Kit-B1

7.2 Product Specifications

7.2.1 Product Specifications

0017-2617

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Copyboard stream reading, fixed reading

Body desktop
Light source type LED array (CIS)
Photosensitive medium OPC drum (30-mm dia.)
Image reading method CCD (CIS)
Reproduction method indirect electrostatic
Exposure method by laser light
Charging method by AC charging roller
Development method 1-component toner projection
Transfer method by transfer roller
Separation method by curvature + static eliminator
Cassette pickup method retard
Multifeeder pickup method dual processing
Drum cleaning method by cleaning blade
Fixing method on-demand
Delivery method face-down
Reproduction ratio 50% to 200%

89
 Chapter 7

Warm-up time approx. 26sec

Image margin (leading edge) 3.0 -/+1.5 mm
Image margin (trailing edge) 3.0 -/+2.0 mm
Image margin (left/right) left edge: 3.0 -/+2.0 mm
right edge: 0.5 mm or more
Non-image width (leading edge) 3.0 -/+2.0 mm
Non-image width (trailing edge) 5.0 -/+2.0 mm
Non-image width (left/right) 3.0 -/+2.0 mm
Number of gradations 256 gradations
Reading resolution 600 x 600 dpi
Printing resolution 1200 dpi x 1200 dpi
First print time 6.9 sec or less
Cassette capacity 250sheets (80 g/m2)
Multifeeder tray capacity 100 sheets (A4/B5/LTR, 64 g/m2)
50 sheets (A3/B4/LDR/LGL, 64 g/m2)
100 sheets (A5/A5R/STMT, 64 g/m2)
80 sheets (A4/B5/LTR, 80 g/m2)
50 sheets (A3/B4/LDR/LGL, 80 g/m2)
80 sheets (A5/A5R/STMT, 80 g/m2)
50 sheets (heavy paper, A4/B5/LTR, 105 g/m2)
50 sheets (heavy paper, A3/B4/LDR/LGL, 105 g/m2)
50 sheets (heavy paper, A5/A5R/STMT, 105 g/m2)
50 sheets (heavy paper, A4/B5/LTR, 128 g/m2)
35 sheets (heavy paper, A3/B4/LDR/LGL, 128 g/m2)
50 sheets (heavy paper, A5/A5R/STMT, 128 g/m2)
50 sheets (OHP)
1 sheet (label)
10 sheets (envelope)
40 sheets (post card)
Continuous reproduction 1 to 99 sheets
Toner type magnetic negative toner
Original type sheet, book
Maximum original size A3/LDR
Original size detection function by reflection type sensor (iR2018/2018N/2018i: Non-equipment)
Sleep mode yes
Option See the system configuration chart.
Operating environment 15 to 27.5 deg C
(temperature range)
Operating environment 25% to 75%
(humidity range)
Operating environment 0.6 to 1.0 atm
(atmospheric pressure)
Noise iR2030 series: 69.5 dB or less
iR2025 series: 67.75 dB or less
iR2022 series: 66.7 dB or less
iR2018 series: 65.5 dB or less
Power supply rating 120/230V
Power consumption (maximum) 120V model: 1423 W or less
230V model: 1499 W or less
Power consumption Average power consumption
120V model: 646 W or less (At the option full-equipped: 690 W)
230V model: 612 W or less (At the option full-equipped: 622 W)
Ozone 0.01 ppm or less (initial)
0.035 ppm or less (after endurance)
Dimensions Platen/1-casette model: 622mm x 638mm x 580.4mm (WxDxH)
Platen/2-casettes model: 622mm x 638mm x 665.4mm (WxDxH)
ADF/1-casette model: 622mm x 676mm x 672mm (WxDxH)
ADF/2-casettes model: 622mm x 676mm x 757mm (WxDxH)
Weight Platen/1-casette model: approx. 41 kg
Platen/2-casettes model: approx. 47 kg
ADF/1-casette model: approx. 47 kg
ADF/2-casettes model: approx. 53 kg

7.3 Function List

7.3.1 Printing Speed (iR2030/iR2030i)

0017-5909

iR2030

90
 Chapter 7

Paper size Single-sided Double-sided

Casette feed Manual feed Casette feed Manual feed
Plain paper A4 30 30 27.5 27.5
A5 25.5 25.5 - -
A5R - 9.5 - 9
B5 23 23 22.5 22.5
B5R 9 9 9 9
A4R 11 11 9.5 9.5
B4 11 11 9 9
A3 15 15 10 10
STMT 10.5 10.5 - 9
STMTR - 9.5 - 9
EXE - 23 - 21
LTR 30 30 27.5 27.5
LTRR 11.5 11.5 9.5 9.5
LGL 11 11 9 9
LDR 15 15 9.5 9.5
8K 10.5 10.5 9 9
16K 23 23 22.5 22.5
16KR 11 11 9 9
Heavy paper; 81 to 105g/ A4 23 (-) 23 (23) 22 (-) 22 (-)
m2 *1 A5 47.5 (-) 17.5 (7.5) - -
(Heavy paper; 106 to A5R - 10 (7) - 8 (-)
128g/m2 *2) B5 16.5 (-) 16.5 (8) 16 (-) 16 (-)
B5R 8 (-) 8 (7.5) 7.5 (-) 7.5 (-)
A4R 9.5 (-) 9.5 (5.5) 9 (-) 9 (-)
B4 9.5 (-) 9.5 (6.5) 8.5 (-) 8.5 (-)
A3 14 (-) 14 (14) 9.5 (-) 9.5 (-)
STMT 9 (-) 9 (8) - 8 (-)
STMTR - 8 (7.5) - -
EXE - 16.5 (8) - 15.5 (-)
LTR 22.5 (-) 22.5 (22.5) 22 (-) 22 (-)
LTRR 9.5 (-) 9.5 (4.5) 9 (-) 9 (-)
LGL 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
LDR 13.5 (-) 13.5 (13.5) 9.5 (-) 9.5 (-)
8K 9 (-) 9 (4.5) 8 (-) 8 (-)
16K 16.5 (-) 16.5 (8) 16 (-) 16 (-)
16KR 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
Bond paper *3 A4 - 7.5 (6) - 7.5 (6)
A5 - 6 (5) - -
(Bond paper H *4)
A5R - 6 (5) - 6 (4.5
B5 - 6 (5) - 6 (5)
B5R - 5.5 (4.5) - 5.5 (4)
A4R - 4.5 (4) - 4.5 (3.5)
B4 - 5.5 (4.5) - 5 (4)
A3 - 6 (5) - 6 (5)
STMT 6.5 (5) 6.5 (5) - -
STMTR - 6 (5) - 5.5 (4.5)
EXE - 6 (5) - -
LTR 7.5 (6) 7.5 (6) 7.5 (6) 7.5 (6)
LTRR 4.5 (4) 4.5 (4) 4.5 (3) 4.5 (3)
LGL 4 (3.5) 4 (3.5) 3.5 (3) 3.5 (3)
LDR 6 (5) 6 (5) 6 (5) 6 (5)
8K - - - -
16K - - - -
16KR - - - -
OHP A4 - 30 - -
LTR - 30 - -
Envelope Monarch - 6.1 - -
COM10 - 6 - -
ISO-B5 - 6.1 - -
ISO-C5 - 6 - -
DL - 6 - -
Postcard Postcard - 11.5 - -
Double postal card - 10.5 - -
4-plane post card - 23.5 - -

91
 Chapter 7

*1. Bond SP. FIX. Mode in the user mode: OFF

*2. Bond SP. FIX. Mode in the user mode: ON
Supplement:
- The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the cassette feeding
module.
- The copy speed may become down when the copies make continuously one minutes or more with the narrow width paper. The slowdown is reduced with the
following user mode. User Mode: Additional Functions > Adjust/Cleaning > Spesial Mode S > Speed Priority 1 or 2

7.3.2 Printing Speed (iR2025/iR2025i)

0018-0333

iR2025

92
Chapter 7

93
 Chapter 7

T-7-1

Paper size Single-sided Double-sided

Casette feed Manual feed Casette feed Manual feed
Plain paper A4 25 25 23.5 23.5
A5 25.5 25.5 - -
A5R - 9.5 - 9
B5 23 23 22.5 22.5
B5R 9 9 9 9
A4R 11 11 9.5 9.5
B4 11 11 9 9
A3 15 15 10 10
STMT 10.5 10.5 - 9
STMTR - 9.5 - 9
EXE - 23 - 21
LTR 25 25 27.5 27.5
LTRR 11.5 11.5 9.5 9.5
LGL 11 11 9 9
LDR 15 15 9.5 9.5
8K 10.5 10.5 9 9
16K 23 23 22.5 22.5
16KR 11 11 9 9
Heavy paper; 81 to 105g/ A4 23 (-) 23 (23) 22 (-) 22 (-)
m2 *1 A5 47.5 (-) 17.5 (7.5) - -
(Heavy paper; 106 to A5R - 10 (7) - 8 (-)
128g/m2 *2) B5 16.5 (-) 16.5 (8) 16 (-) 16 (-)
B5R 8 (-) 8 (7.5) 7.5 (-) 7.5 (-)
A4R 9.5 (-) 9.5 (5.5) 9 (-) 9 (-)
B4 9.5 (-) 9.5 (6.5) 8.5 (-) 8.5 (-)
A3 14 (-) 14 (14) 9.5 (-) 9.5 (-)
STMT 9 (-) 9 (8) - 8 (-)
STMTR - 8 (7.5) - -
EXE - 16.5 (8) - 15.5 (-)
LTR 22.5 (-) 22.5 (22.5) 22 (-) 22 (-)
LTRR 9.5 (-) 9.5 (4.5) 9 (-) 9 (-)
LGL 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
LDR 13.5 (-) 13.5 (13.5) 9.5 (-) 9.5 (-)
8K 9 (-) 9 (4.5) 8 (-) 8 (-)
16K 16.5 (-) 16.5 (8) 16 (-) 16 (-)
16KR 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
Bond paper *3 A4 - 7.5 (6) - 7.5 (6)
A5 - 6 (5) - -
(Bond paper H *4)
A5R - 6 (5) - 6 (4.5
B5 - 6 (5) - 6 (5)
B5R - 5.5 (4.5) - 5.5 (4)
A4R - 4.5 (4) - 4.5 (3.5)
B4 - 5.5 (4.5) - 5 (4)
A3 - 6 (5) - 6 (5)
STMT 6.5 (5) 6.5 (5) - -
STMTR - 6 (5) - 5.5 (4.5)
EXE - 6 (5) - -
LTR 7.5 (6) 7.5 (6) 7.5 (6) 7.5 (6)
LTRR 4.5 (4) 4.5 (4) 4.5 (3) 4.5 (3)
LGL 4 (3.5) 4 (3.5) 3.5 (3) 3.5 (3)
LDR 6 (5) 6 (5) 6 (5) 6 (5)
8K - - - -
16K - - - -
16KR - - - -
OHP A4 - 30 - -
LTR - 30 - -
Envelope Monarch - 6.1 - -
COM10 - 6 - -
ISO-B5 - 6.1 - -
ISO-C5 - 6 - -
DL - 6 - -
Postcard Postcard - 11.5 - -
Double postal card - 10.5 - -
4-plane post card - 23.5 - -

94
 Chapter 7

*1. Bond SP. FIX. Mode in the user mode: OFF

*2. Bond SP. FIX. Mode in the user mode: ON
Supplement:
- The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the cassette feeding
module.
- The copy speed may become down when the copies make continuously one minutes or more with the narrow width paper. The slowdown is reduced with the
following user mode. User Mode: Additional Functions > Adjust/Cleaning > Spesial Mode S > Speed Priority 1 or 2

7.3.3 Printing Speed (iR2022/iR2022i/iR2022K/iR2022N))

0018-0334

iR2022i / iR2022

95
 Chapter 7

96
T-7-2
 Paper size Single-sided Double-sided
Casette feed Manual feed Casette feed Manual feed
Plain paper A4 22 22 21 21
A5 25.5 25.5 - -
A5R - 9.5 - 9
B5 23 23 22.5 22.5
B5R 9 9 9 9
A4R 11 11 9.5 9.5
B4 11 11 9 9
A3 15 15 10 10
STMT 10.5 10.5 - 9
STMTR - 9.5 - 9
EXE - 23 - 21
LTR 22 22 27.5 27.5
LTRR 11.5 11.5 9.5 9.5
LGL 11 11 9 9
LDR 15 15 9.5 9.5
8K 10.5 10.5 9 9
16K 23 23 22.5 22.5
16KR 11 11 9 9
Heavy paper; 81 to 105g/ A4 23 (-) 23 (23) 22 (-) 22 (-)
m2 *1 A5 47.5 (-) 17.5 (7.5) - -
(Heavy paper; 106 to A5R - 10 (7) - 8 (-)
128g/m2 *2) B5 16.5 (-) 16.5 (8) 16 (-) 16 (-)
B5R 8 (-) 8 (7.5) 7.5 (-) 7.5 (-)
A4R 9.5 (-) 9.5 (5.5) 9 (-) 9 (-)
B4 9.5 (-) 9.5 (6.5) 8.5 (-) 8.5 (-)
A3 14 (-) 14 (14) 9.5 (-) 9.5 (-)
STMT 9 (-) 9 (8) - 8 (-)
STMTR - 8 (7.5) - -
EXE - 16.5 (8) - 15.5 (-)
LTR 22.5 (-) 22.5 (22.5) 22 (-) 22 (-)
LTRR 9.5 (-) 9.5 (4.5) 9 (-) 9 (-)
LGL 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
LDR 13.5 (-) 13.5 (13.5) 9.5 (-) 9.5 (-)
8K 9 (-) 9 (4.5) 8 (-) 8 (-)
16K 16.5 (-) 16.5 (8) 16 (-) 16 (-)
16KR 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
Bond paper *3 A4 - 7.5 (6) - 7.5 (6)
A5 - 6 (5) - -
(Bond paper H *4)
A5R - 6 (5) - 6 (4.5
B5 - 6 (5) - 6 (5)
B5R - 5.5 (4.5) - 5.5 (4)
A4R - 4.5 (4) - 4.5 (3.5)
B4 - 5.5 (4.5) - 5 (4)
A3 - 6 (5) - 6 (5)
STMT 6.5 (5) 6.5 (5) - -
STMTR - 6 (5) - 5.5 (4.5)
EXE - 6 (5) - -
LTR 7.5 (6) 7.5 (6) 7.5 (6) 7.5 (6)
LTRR 4.5 (4) 4.5 (4) 4.5 (3) 4.5 (3)
LGL 4 (3.5) 4 (3.5) 3.5 (3) 3.5 (3)
LDR 6 (5) 6 (5) 6 (5) 6 (5)
8K - - - -
16K - - - -
16KR - - - -
OHP A4 - 30 - -
LTR - 30 - -
 Envelope Monarch - 6.1 - -
COM10 - 6 - -
ISO-B5 - 6.1 - -
ISO-C5 - 6 - -
DL - 6 - -
Postcard Postcard - 11.5 - -
Double postal card - 10.5 - -
4-plane post card - 23.5 - -

*1. Bond SP. FIX. Mode in the user mode: OFF

*2. Bond SP. FIX. Mode in the user mode: ON
Supplement:
- The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the
cassette feeding module.
- The copy speed may become down when the copies make continuously one minutes or more with the narrow width paper. The slowdown is reduced
with the following user mode. User Mode: Additional Functions > Adjust/Cleaning > Spesial Mode S > Speed Priority 1 or 2

7.3.4 Printing Speed (iR2018/iR2018i/iR2018N)

0018-0335

iR2018 / iR2018i
T-7-3
 Paper size Single-sided Double-sided
Casette feed Manual feed Casette feed Manual feed
Plain paper A4 18 18 18 18
A5 25.5 25.5 - -
A5R - 9.5 - 9
B5 23 23 22.5 22.5
B5R 9 9 9 9
A4R 11 11 9.5 9.5
B4 11 11 9 9
A3 15 15 10 10
STMT 10.5 10.5 - 9
STMTR - 9.5 - 9
EXE - 23 - 21
LTR 18 18 27.5 27.5
LTRR 11.5 11.5 9.5 9.5
LGL 11 11 9 9
LDR 15 15 9.5 9.5
8K 10.5 10.5 9 9
16K 23 23 22.5 22.5
16KR 11 11 9 9
Heavy paper; 81 to 105g/ A4 23 (-) 23 (23) 22 (-) 22 (-)
m2 *1 A5 47.5 (-) 17.5 (7.5) - -
(Heavy paper; 106 to A5R - 10 (7) - 8 (-)
128g/m2 *2) B5 16.5 (-) 16.5 (8) 16 (-) 16 (-)
B5R 8 (-) 8 (7.5) 7.5 (-) 7.5 (-)
A4R 9.5 (-) 9.5 (5.5) 9 (-) 9 (-)
B4 9.5 (-) 9.5 (6.5) 8.5 (-) 8.5 (-)
A3 14 (-) 14 (14) 9.5 (-) 9.5 (-)
STMT 9 (-) 9 (8) - 8 (-)
STMTR - 8 (7.5) - -
EXE - 16.5 (8) - 15.5 (-)
LTR 22.5 (-) 22.5 (22.5) 22 (-) 22 (-)
LTRR 9.5 (-) 9.5 (4.5) 9 (-) 9 (-)
LGL 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
LDR 13.5 (-) 13.5 (13.5) 9.5 (-) 9.5 (-)
8K 9 (-) 9 (4.5) 8 (-) 8 (-)
16K 16.5 (-) 16.5 (8) 16 (-) 16 (-)
16KR 9.5 (-) 9.5 (4.5) 8.5 (-) 8.5 (-)
Bond paper *3 A4 - 7.5 (6) - 7.5 (6)
A5 - 6 (5) - -
(Bond paper H *4)
A5R - 6 (5) - 6 (4.5
B5 - 6 (5) - 6 (5)
B5R - 5.5 (4.5) - 5.5 (4)
A4R - 4.5 (4) - 4.5 (3.5)
B4 - 5.5 (4.5) - 5 (4)
A3 - 6 (5) - 6 (5)
STMT 6.5 (5) 6.5 (5) - -
STMTR - 6 (5) - 5.5 (4.5)
EXE - 6 (5) - -
LTR 7.5 (6) 7.5 (6) 7.5 (6) 7.5 (6)
LTRR 4.5 (4) 4.5 (4) 4.5 (3) 4.5 (3)
LGL 4 (3.5) 4 (3.5) 3.5 (3) 3.5 (3)
LDR 6 (5) 6 (5) 6 (5) 6 (5)
8K - - - -
16K - - - -
16KR - - - -
OHP A4 - 30 - -
LTR - 30 - -
 Envelope Monarch - 6.1 - -
COM10 - 6 - -
ISO-B5 - 6.1 - -
ISO-C5 - 6 - -
DL - 6 - -
Postcard Postcard - 11.5 - -
Double postal card - 10.5 - -
4-plane post card - 23.5 - -

*1. Bond SP. FIX. Mode in the user mode: OFF

*2. Bond SP. FIX. Mode in the user mode: ON
Supplement:
- The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the
cassette feeding module.
- The copy speed may become down when the copies make continuously one minutes or more with the narrow width paper. The slowdown is reduced
with the following user mode. User Mode: Additional Functions > Adjust/Cleaning > Spesial Mode S > Speed Priority 1 or 2

7.3.5 Types of Paper

0017-5914

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Source
Type Paper size
Manual Feed Tray Cassette

Plain paper, eco paper, recycled paper A3, B4, A4, A4R, B5, B5R, A5, LDR, LGL, LTR, Yes Yes
(64-90g/m2) LTRR, STMT, 8K, 16K

A5R, STMTR Yes No

Special paper Heavy paper Width: 95mm-297mm Yes No

(90-128g/m2) Length: 148mm-432mm

OHP A4, LTR Yes No

Postcard Postcard A6R modified Yes No

4-plane postcard A4 modified Yes No

Label paper A4, B4, LTR Yes No

3-hole paper LTR Yes Yes

Envelope Com10, Monarch, DL, ISO-C5, ISO-B5 Yes No

 Chapter 8

Chapter 8 Upgrading

8.1 Upgrading

8.1.1 Overview of Upgrade (LCD type)

0017-6002

iR2018 / iR2022

This machine and options can be upgraded by downloading system software programs from the personal computer (hereafter called as the PC) in which a service
support tool (hereafter called SST) has been loaded.
System software programs and upgrade tools are listed in the following table:
T-8-1

Type System software type Upgrade tool Remarks

SST
Main unit System (main controller) The main controller also controls
Yes the reader.

Boot (boot program)

Yes

Option PCL (PCL printer kit-V1)

Yes

Fin_U2 (Finisher-U2) Dedicated service tool

Yes (Downloader PCB: FY9-2034)

Pay attention to the following points when updagrading.

1. When updagrading Boot, make sure to update Boot first.
2. When updagrading the following software, make sure to update all to the same version.
- System
- PCL

8.1.2 Overview of Upgrade (Touch panel type)

0017-6004

iR2022i / iR2025 / iR2030 / iR2018i

97
 Chapter 8

This machine and options can be upgraded by downloading system software programs from the personal computer (hereafter called as the PC) in which a service
support tool (hereafter called SST) has been loaded.
System software programs and upgrade tools are listed in the following table:
T-8-2

Type System software type Upgrade tool Remarks

SST
Main unit System (main controller) Yes Main controller also controls the reader.

Boot (boot program) Yes

Language (language module) Yes USB memory

PCL_op Yes 16MB ROM PCB

Option PCL_common (PCL Printer Kit-W1) Yes *1

Fin_U2 (Finisher-U2) Yes Dedicated service tool (Downloader PCB:

FY9-2034)

*1. PCL_common is the software stored in the optionally available extended 32MB ROM PCB. It consists of the firmware for PCL printer function and the main
control firmware. Inserting the 32MB ROM PCB in the extended slot in the image processor PCB allows the main controller to operate under the control of the
firmware stored in the 32MB ROM PCB.

Pay attention to the following points when updagrading.

1. When updagrading Boot, make sure to update Boot first.
2. When updagrading the following software, make sure to update all to the same version.
- System
- Language
- PCL

8.1.3 Overview of Service Support Tool (LCD type)

0017-6005

iR2018 / iR2022

Main unit PC

Image processor PCB

USB cable
Flash ROM CPU
J303

SST

PCL printer kit-V1 System

software

32MB ROM PCB

RS232C
straight cable
Flash ROM

Downloader
PCB

Finisher-U2 FY9-2034

Finisher controller PCB

Flash ROM CPU

J918

F-8-1
When using the SST, select "#DOWNLOAD" in the service mode to place the main unit in the download mode. (The finisher need not enter the download mode.)

8.1.4 Overview of Service Support Tool (Touch panel type)

0017-6006

iR2022i / iR2025 / iR2030 / iR2018i

98
 Chapter 8

Main unit PC

Image processor PCB

16MB ROM
USB cable
Flash ROM CPU
J303

SST

16MB ROM PCB System

software
Flash ROM
RS232C
straight cable

USB Memory

Flash Memory Downloader

PCB

FY9-2034
PCL printer kit-W1

32MB ROM PCB

Flash ROM

Finisher-U2

Finisher controller PCB

Flash ROM CPU

J918

F-8-2
When using the SST, select "#DOWNLOAD" in the service mode to place the main unit in the download mode. (The finisher need not enter the download mode.)

99
Aug 8 2007