Scribd
Upload
218 views1 page

Wqt-1-13-W-1-3g-Smaw-Alclad-Aws D1.1

1. Mr. JOVEN LISSA successfully qualified as a welder on March 11, 2012 using the shielded metal arc welding (SMAW) process with single electrode in the downhill position for butt joints in steel plates up to 30mm thick. 2. The welder demonstrated qualification in the flat, horizontal, and vertical positions for both fillet and groove welds within the specified ranges. 3. Radiographic testing and a visual examination of the test welds were completed and found to be acceptable based on the standards.

Uploaded by

Rejoy baby
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
218 views1 page

Wqt-1-13-W-1-3g-Smaw-Alclad-Aws D1.1

1. Mr. JOVEN LISSA successfully qualified as a welder on March 11, 2012 using the shielded metal arc welding (SMAW) process with single electrode in the downhill position for butt joints in steel plates up to 30mm thick. 2. The welder demonstrated qualification in the flat, horizontal, and vertical positions for both fillet and groove welds within the specified ranges. 3. Radiographic testing and a visual examination of the test welds were completed and found to be acceptable based on the standards.

Uploaded by

Rejoy baby
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 1

WELDER QUALIFICATION TEST RECORD

Welder name Mr.JOVEN LISSA Welder ID # ACS-W-001


WPS # WPS/ACS/001 PQR # PQR/ACS
Base Material EN 10025 S 275JR WPQR No. --
Thickness 15 mm Date of Qualification 03/11/2012
WELDING VARIABLES ACTUAL VALUES RANGE QUALIFIED
Welding Process(es) / type SMAW / MANUAL SMAW / MANUAL
Current type / polarity DCEP DCEP
Electrode (single or multiple) Single Single
Backing Without With or without
Material / Specification EN 10025 S 275 JR
Plate, Pipe or Tube Plate
Groove or Fillet Groove
Material thickness(mm) 15 mm 3mm to 30 mm
Pipe Diameter N/A See position
Groove F,H,V
Plate
Fillet F,H,V except dihedral angles < 30º
Butt Groove F,H,V-24″ø & above
CJP T,-Y,-K,- Not Qualified
Pipe PJP T,-Y,-K,- F,H,V-24″ø & above except groove
Position 3G angles < 30º
Fillet F,H,V except dihedral angles < 30º
Butt Groove F,H,V
Box CJP T,-Y,-K,- Not Qualified
tube PJP T,-Y,-K,- F,H,V except groove angles < 30º
Fillet F,H,V except dihedral angles < 30º
Vertical Progression Uphill Uphill
Filler metal (SFA) SFA 5.1
Filler metal classification E 7018
Gas/flux type N/A
F-Number (for SMAW only) F4 F1, F2, F3, F4
Other N/A N/A

TEST RESULT REPORT


Visual Test Acceptable N/A
Radiography Test Acceptable RT-28249- DATED 02-11-2012
Tensile Test N/A N/A
Guided Bend Test N/A N/A
We certify that the statements in this record are correct and that the test coupons were prepared, welded and tested
in accordance with the requirements of AWS D1.1 Ed 2010
Test witnessed by: Mr. Rajpal Singh Tested on: 02-11-2012
Manufacturer Examiner or Examining Body
Name Mr. Simon C. Woodhouse Mr. RAJPAL SINGH

Signature

INTERFACE TECHNICAL
Organization All Clad Seaco (middle east) LLC
INSPECTION
Date 03.11.2012 03.11.2012

You might also like