Scribd
Upload
525 views

Manual Boeco r-400-110629

1. This document provides instructions for operating an oil-free vacuum pump. 2. It describes how to unpack, install, and connect the pump according to the safety notices and warnings. 3. Operating instructions explain how to start and regulate the pump, replace the filter cartridge, and pour out water from the moisture trap.

Uploaded by

Celeynes RT
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
525 views

Manual Boeco r-400-110629

1. This document provides instructions for operating an oil-free vacuum pump. 2. It describes how to unpack, install, and connect the pump according to the safety notices and warnings. 3. Operating instructions explain how to start and regulate the pump, replace the filter cartridge, and pour out water from the moisture trap.

Uploaded by

Celeynes RT
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Oil-Free Vacuum Pump

R-400
A. Important Notice

This instrument is designed for laboratory usage only.

Before setting up and operating the Vacuum Pump, please read these instructions carefully to
familiarize with all installation and operation process. Any individual shall be well trained by
reading the instructions or by technical people from authorized distributors before operating the
instrument.
The instrument shall not be modified or altered in any way. Any modification or alteration

will void the warranty, void the regulatory certifications and create potential safety hazard.
We are not responsible for any injury or damage caused by using the instrument for any
non-intended purpose, or modifying the instrument by any person who is not authorized.

B. Unpacking

When unpacking, notice if the pump is in good situation. If not, please contact the distributor or

contact us by e-mail: [email protected] immediately for assistance.

C. Installation

1. Check voltage specified on nameplate on the bottom. Make sure if it matches the line

voltage in your location.

2. Install the instrument in a clean, dust-less and ventilated area under 40 .


3. To enable suction function, connect the inlet of the pump to the outlet of objective
equipment with a high-pressure hose.
D. Warning

1. The pump is not corrosion-proof. Please do not operate it with corrosive gases
directly.

2. When pump is used in water filtration, do not make the liquid level of flask exceed
safety level. Failure to comply can result in serious damage to the pump and void the
warranty. If it occurs, please contact the distributor immediately for service.
3. The filter cartridge is used to absorb moisture and dust. Please replace the cartridge to

maintain proper pumping efficiency when it is saturated.


4. If the pump does not work when restarted during operation, release the vacuum, and
turn-on again. Otherwise may result overloading and damaging the motor.
5. This pump has a thermal switch that automatically shuts-off when it becomes overheated

or lack of voltage.

6. Do not touch the pump during working or just after use as motor is hot. (70~80 )
7. Do not use any lubricant, which may damage the pump.

8. Use the pump in a dry, clean well-ventilated area.


9. Never spray flammable or toxic materials.

10. If the supply cord is damaged, it must be replaced by the manufacturer, service agent or a
competent person in order to avoid hazard.
E. Operation
2.Outlet

3.On/Off

1.Inlet

5.Catridge

6.Moisture Trap

4.Regulator

Operating procedure
1. Schematic of the pump system is shown as above.
2. Once all of tubes have been connected, Press on/off button to start working.
3. To setup vacuum, adjust the regulator .
* Warning: When pump is used in water filtration, please be note, never let the
liquid level of flask exceed safety level. Failure to comply could result in serious
damage to the pump and void the warranty. If it occurs, please contact the
distributor immediately for service.

How to replace cartridge


1. You are recommended to replace the cartridge when it is exhausted with moisture
or particle.
2. First, remove the moisture trap cup by rotating it counterclockwise. Second,
remove the cartridge in the same way then replace a new one.
3. Pour the water out of the moisture trap cup when it is filled with water.
F. Parts List
G. Ordering Information

BOE 8840100 BOECO R-400 Vacuum pump, AC 110V, 60Hz


BOE 8840000 BOECO R-400 Vacuum pump, AC 220V, 50/60Hz
BOE 167300-06 Moisture trap / vacuum regulator
BOE 167300-07 Filter cartridge
BOE 167400-60 Repair kit for BOECO R-400

Please visit www.boeco.com for more information

You might also like