D342 VEHICULAR ENGINE 76V00001-00504 (MACHINE)(UEG0890S - 00) - Sistemas y componentes
Cerrar SIS
Pantalla anterior
Producto: TRACK-TYPE TRACTOR
Modelo: D8K TRACK-TYPE TRACTOR 76V00001
Configuración: D342 VEHICULAR ENGINE 76V00001-00504 (MACHINE)
Desarmado y Armado
D342 VEHICULAR ENGINE FOR D8K TRACTOR
Número de medio -SENR7010-01 Fecha de publicación -01/09/1977 Fecha de actualización -12/10/2001
Cylinder Heads (Earlier)
SMCS - 1101-11; 1101-12
Remove Cylinder Heads (Earlier)
start by:
a) remove inlet manifold
b) remove exhaust manifold
c) remove water manifold
d) remove fuel injection lines
e) remove rocker shafts and push rods
1. Remove the bolts that hold bracket (4) to the cylinder head.
2. Disconnect two oil lines (3) from oil manifold (1) for the bulldozer tilt cylinder. Remove bolts (2) and move
manifold clear of the cylinder head.
3. Disconnect vent line (6) from the cylinder head.
4. Remove bolts (5) that hold the valve cover base (7) to the cylinder head. Remove the valve cover base.
5. Remove nuts (9) and washers that hold the cylinder head to the cylinder block.
https://127.0.0.1/...isweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sisweb/sisweb/techdoc/techdoc_print_page.jsp[30/11/2020 08:39:38]
D342 VEHICULAR ENGINE 76V00001-00504 (MACHINE)(UEG0890S - 00) - Sistemas y componentes
6. Install two 3/8" - 16 NC forged eyebolts in the cylinder head. Fasten a hoist to the cylinder head. Remove the
front cylinder head (8). Weight of the cylinder head is 230 lb. (104 kg).
7. Disconnect linkages (11) from the governor shaft (10). Remove bolts (12). Remove the shaft.
8. Do Steps 4 through 6 and remove the rear cylinder head (13). Weight of the rear cylinder head is 230 lb. (104 kg).
Install Cylinder Heads (Earlier)
1. Clean the gasket surfaces of the cylinder heads and block.
2. Install new gaskets. Install new ferrules and seals. Install the ferrules, with the ends that have a taper (rolled ends)
toward the cylinder head.
3. Install two 3/8" - 16 NC forged eyebolts in the cylinder heads. Fasten a hoist to the eyebolts. Install the cylinder
heads (1) slowly over their studs on the cylinder block.
https://127.0.0.1/...isweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sisweb/sisweb/techdoc/techdoc_print_page.jsp[30/11/2020 08:39:38]
D342 VEHICULAR ENGINE 76V00001-00504 (MACHINE)(UEG0890S - 00) - Sistemas y componentes
4. Put 4S9416 Anti-Seize Compound on the threads of the nuts for the cylinder head studs. Install the washers and
nuts. Tighten the nuts in the following step sequence:
1: Tighten the 5/8" nuts in number sequence to a torque of 60 lb.ft. (80 N·m).
2: Tighten the 7/8" nuts in letter sequence to a torque of 150 lb.ft. (205 N·m).
3: Tighten the 7/8" nuts again in letter sequence to a torque of 300 lb.ft. (410 N·m).
4: Tighten the 5/8" nuts again in number sequence to a torque of 120 lb.ft. (160 N·m).
5: Tighten the 7/8" nuts again in letter sequence by hand to a torque of 300 lb.ft. (410 N·m).
6: Tighten the 5/8" nuts again in number sequence by hand to a torque of 120 lb.ft. (160 N·m).
5. Install the valve cover bases (3) on the cylinder heads.
6. Install the two bolts that connect the bracket on the rear cylinder head to the dash.
7. Put governor control shaft (4) in position on the rear cylinder head. Install the bolts that hold it. Connect the
linkages to the shaft.
8. Put oil manifold (2) in position on the bulldozer tilt cylinder. Install the bolts that hold it. Connect two oil lines to
the oil manifold.
9. Connect vent line (5) to the front cylinder head.
end by:
a) install rocker shafts and push rods
b) install fuel injection lines
c) install water manifold
d) install exhaust manifold
e) install inlet manifold
Copyright 1993 - 2020 Caterpillar Inc. Mon Nov 30 08:39:26 EST 2020
Todos los derechos reservados.
Red privada para licenciados del SIS.
https://127.0.0.1/...isweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sisweb/sisweb/techdoc/techdoc_print_page.jsp[30/11/2020 08:39:38]
