ELECTRONIC EQUIPMENT REPAIR CENTRE : SONY HBD-N890W - Service mode - Test mode – factory reset – laser pick up replacement

procedure – how to eject the disc – Bluray player repair...

Περισσότερα
Δημιουργία ιστολογίου
Συνδεση

ELECTRONIC EQUIPMENT REPAIR CENTRE

Electronic equipment disassembly, adjustments, repair, software updates and more. Cameras, mobile phones, treadmills, TVs, VCrs, Blu-rays etc:

SONY HBD-N890W - Service mode - Test mode – Translate

factory reset – laser pick up replacement procedure – Επιλογή γλώσσας​▼
how to eject the disc – Bluray player repair and service
Category: Blu ray Player Repair Search This Blog
and Service 
Contents of this article 
How to access service mode  Search

Demo mode 

Factory reset procedure

Laser pick up replacement 

Total Pageviews

SONY HBD-N890W
2,413,389

HOW TO EJECT THE DISC WHEN POWER SWITCH TURN OFF

The BD drive is taken out, and please rotate the pulley in the direction of the arrow
by screwdriver etc. after detaching and take out the disc.

Blog Archive

February (190)
February (190)

TEST MODE
COLD RESET (MAIN UNIT)
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [POWER] button to turn the power on.
2. Touch the [STOP ] and [VOL –] sensors simultaneously and hold down (around
5 seconds).
3. The message “RESET” appears on fluorescent indicator tube, then becomes
standby states.
COLD RESET (SURROUND AMPLIFIER)
Execute this mode when returning the unit to the customers.
Note 1: The main unit corresponding to TA-SA300WR, wireless transceivers
(EZW-RT50 (HBD-N790W/N890W/N990W/T79) or EZW-RT20 (HBD-N995W)) (2
units) and the remote commander corresponding to the main unit are necessary to
execute this mode.
Procedure:

https://electro-medical.blogspot.com/2016/02/sony-hbd-n890w-service-mode-test-mode.html[28/10/2020 10:01:12 πμ]

ELECTRONIC EQUIPMENT REPAIR CENTRE : SONY HBD-N890W - Service mode - Test mode – factory reset – laser pick up replacement procedure – how to eject the disc – Bluray player repair...

1. Insert the wireless transceiver (EZW-RT50 (HBD-N790W/ N890W/N990W/T79)

or EZW-RT20 (HBD-N995W)) of the attachment in the wireless transceiver slot in
the back of the main unit (HBD-N790W/N890W/N990W/N995W/T79) and the
surround amplifier (TA-SA300WR).
2. Connect the AC power cord of the main unit (HBD-N790W/
N890W/N990W/N995W/T79).
3. Press the [POWER] button on the main unit (HBD-N790W/
N890W/N990W/N995W/T79).
4. Connect the AC power cord of the surround amplifier (TASA300WR).
5. When a wireless transceiving becomes effective, the [LINK/ STANDBY]
indicator of surround amplifier (TA-SA300WR) lights to green.
Note 2: Refer to the operating instructions when the [LINK/STANDBY] indicator of
surround amplifier (TA-SA300WR) doesn’t ligh
6. Press the button in order of the [DISPLAY] > [0] > [7] > [2] >  [SUBTITLE] on the
remote commander corresponding to main unit aiming at the main unit.
7. Confirm the [LINK/STANDBY] indicator of TA-SA300WR is orange lighting after
step 3 is executed.
8. The AC plug of TA-SA300WR is pulled out to turn off the system.
Note 3: Please insert it after confirming the [LINK/STANDBY] indicator of TA-
SA300WR has been turned off when you insert the AC plug again.
CHECKING METHOD OF NETWORK OPERATION
It is necessary to check the network operation, when replacing the MB-149 board
or wireless LAN card (WLC1). Check the operation of wireless and wired LAN,
according to the following method.
Checking Method of Wireless LAN Operation
Check that access point is recognized surely.
Necessary Equipment:
Wireless access point with router function (AP)
Procedure:
1. Press the [HOME] button on the remote commander to enter the home menu.
2. Press the [UP]/[DOWN]/[LEFT]/[RIGHT] buttons on the remote commander to
select “Setup”> “Network Settings”, and press the [ENTER ] button on the remote
commander.
3. Select “Internet Settings”, and press the [ENTER ] button on the remote
commander.
4. Press the [UP]/[DOWN] buttons on the remote commander to select
“Wireless Setup (built-in)”, and press the [ ENTER] button on the remote
commander.
5. The system starts searching for access points, and displays a list of up available
network name (SSID).
6. Check that access point (SSID) is displayed on the searching result.
7. Press the [POWER] button to turn the power off.
Note: Refer to the instruction manual about details of the setting method.
Checking method of wired LAN operation
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the LAN cable.
2. Press the [HOME] button on the remote commander to enter the home menu.
3. Press the [UP]/[DOWN]/[LEFT]/[RIGHT] buttons on the remote commander to
select “Setup”> “Network Settings”, and press the [ ENTER ] button on the remote
commander.
4. Select “Internet Settings”, and press the [ ENTER] button on the remote
commander.
5. Press the [UP]/[DOWN] buttons on the remote commander to select “Wired
Setup”, and press the [ ENTER] button on the remote commander.
6. Press the [UP]/[DOWN] buttons on the remote commander to select “Auto”, and
press the [ ENTER] button on the remote commander.
7. Press the [RIGHT] button on the remote commander.
8. Press the [UP]/[DOWN] buttons on the remote commander to select “Save &
Connect”, and press the [ENTER ] button on the remote commander.
9. When “Internet Settings is now complete.” appears, then press the [ ENTER ]
button on the remote commander.

https://electro-medical.blogspot.com/2016/02/sony-hbd-n890w-service-mode-test-mode.html[28/10/2020 10:01:12 πμ]

ELECTRONIC EQUIPMENT REPAIR CENTRE : SONY HBD-N890W - Service mode - Test mode – factory reset – laser pick up replacement procedure – how to eject the disc – Bluray player repair...

10. Press the [HOME] button on the remote commander to enter the home menu.
11. Press the [UP]/[DOWN]/[LEFT]/[RIGHT] buttons on the remote commander to
select “Setup” > “Network Settings”, and press the [ENTER ] button on the remote
commander.
12. Press the [UP]/[DOWN] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [ ENTER ] button on the remote
commander.
13. Press the [LEFT]/[RIGHT] buttons on the remote commander to select “Start”,
and press the [ ENTER] button on the remote commander.
14. Confirm that “Network connections are correct” is displayed.
15. Press the [POWER] button to turn the power off.
DEMO MODE
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when the [EJECT] sensor is touched. The message “DEMO
LOCK” will be displayed on the fluorescent indicator tube.
Procedure:
1. Press the [POWER] button to turn the power on.
2. Insert a disc.
3. Press the [HOME] button on the remote commander to enter the home menu.
4. Touch the [STOP] and [EJECT] sensors simultaneously and hold down until
“DEMO.LOCK” or “DEMO OFF” displayed on the fluorescent indicator tube
(around 5 seconds).
Releasing method:
Touch the [STOP] and [EJECT] sensors simultaneously and hold down until
“DEMO OFF” displayed on the fluorescent indicator tube (around 5 seconds).
PANEL TEST
Procedure:
1. Press the [POWER] button to turn the power on.
2. Press button in order of the [DISPLAY] > [0] > [0] > [1] > [SUBTITLE] on the
remote commander (Make the interval when each button is pressed within two
seconds).
3. All segments in fluorescent indicator tube are lighted up. And half segments in
fluorescent indicator tube are lighted up, others half segments in fluorescent
indicator tube are lighted up, then all segments in fluorescent indicator tube are
lighted up. This operation is repeated.
4. When all segments in fluorescent indicator tube are lighted up in the state of
step 3, press the [VOL +] button on the remote commander and model information
is displayed on the fluorescent indicator tube. Each time the [VOL +] button on the
remote commander is pressed, the display changes from destination information,
STR version in this order, and returns to the model information display. Each time
the [VOL –] button on the remote commander is pressed, the version and date are
switched.
5. In the state of step 3, press the [FUNCTION] button on the remote commander
and “K 0” is displayed on the fluorescent indicator tube. “K 0” value increases
whenever a button or sensor on the unit is pressed. However, once a button or
sensor has been pressed, it is no longed taken into account. All button and
sensors on the unit are pressed, “OK” and “K 7” are alternately displayed on the
fluorescent indicator tube.
6. In the state of step 3, press the [VOL –] button on the remote commander and
“RM” is displayed on the fluorescent indicator tube. Confirm that “L RM R” is
displayed on the fluorescent indicator tube, while pressing the [VOL –] button on
the remote commander.
The remote control receiver (IC903 on the FL board and IC951 on the SIRCS
board) may be defective when “L” and “R” are not displayed.
Releasing method:
To release from this mode, press the [POWER] button.
DISC SLOT LOCK MODE
The EJECT operation by main unit, remote commander, and CEC (path-through)
can be prohibited.
Procedure:
1. Press the [POWER] button to turn the power on.
2. Insert a disc.

https://electro-medical.blogspot.com/2016/02/sony-hbd-n890w-service-mode-test-mode.html[28/10/2020 10:01:12 πμ]

ELECTRONIC EQUIPMENT REPAIR CENTRE : SONY HBD-N890W - Service mode - Test mode – factory reset – laser pick up replacement procedure – how to eject the disc – Bluray player repair...

3. Press button in order of the [DISPLAY] > [0] > [0] > [4] > [SUBTITLE] on the
remote commander.
(Make the interval when each button is pressed within two seconds)
4. “TLK ON” is displayed on the fluorescent indicator tube, and the EJECT
operation by main unit, remote commander, and CEC (path-through) is prohibited.
Releasing method:
1. Press button in order of the [DISPLAY] > [0] > [0] >  [4] > [SUBTITLE] on the
remote commander. (Make the interval when each button is pressed within two
seconds)
2. “TLK OFF” is displayed on the fluorescent indicator tube, and the EJECT
operation by main unit, remote commander, and CEC (path-through) become
effective.
FACTORY INITIALIZE
Return all of the unit setting to their factory defaults.
Note 1: Disconnect the following connections when you use this mode.
# Front USB
# Rear USB
# LAN
# HDMI IN 1
# HDMI IN 2
Note 2: The operation in this mode must use a remote commander and TV
monitor.
Procedure:
1. Press the [POWER] button to turn the power on.
2. Press the [HOME] button on the remote commander, and the home menu is
displayed.
3. Select “Setup” >  “Resetting”, and press the [ ENTER ] button on the remote
commander.
4. Select “Initialize Personal Information”, and press the [ENTER] button on the
remote commander.
5. Select “OK”, and press the [ ENTER ] button on the remote commander.
6. The message “Close” appears, and press the [ENTER ] button on the remote
commander.
7. Select “Reset to Factory Default Settings”, and press the [ENTER] button on the
remote commander.
8. Select “All Settings”, and press the [ENTER ] button on the remote commander.
9. Select “Start”, and press the [ ENTER ] button on the remote commander.
10. Initialization ends when the message “WELCOME” on the fluorescent indicator
tube disappears.
BD SERVICE MODE
Setting method of the BD service mode:
1. Connect this unit with TV monitor.
2. Press the [POWER] button to turn the power on.
3. Press button in order of the [DISPLAY] > [0] > [2] > [1] > [SUBTITLE] on the
remote commander. (Make the interval when each button is pressed within
two seconds)
4. Enter the BD service mode. The OSD menu on TV monitor can be operated
by remote commander.
Main Functions
# Diag
Performs unit test of devices installed on the board.
# Display Error Log
Error log is displayed. Displayed contents can also be saved in
an USB memory device.
# Factory Initialize
Restores the unit to its factory settings.
# Network
Checks the wired network connection.
# Version Up
Not used.
# System Information
Displays the system information of the unit.

https://electro-medical.blogspot.com/2016/02/sony-hbd-n890w-service-mode-test-mode.html[28/10/2020 10:01:12 πμ]

ELECTRONIC EQUIPMENT REPAIR CENTRE : SONY HBD-N890W - Service mode - Test mode – factory reset – laser pick up replacement procedure – how to eject the disc – Bluray player repair...

Displays information such as the software version, drive information, etc.

# EMC Test Mode
Not used.
# Drive
Write drive OP data and check drive.
# HDD mode
Not used.
Optical device (KEM-480AAA) replacement
Flow of replacement:
Note: The photo in flow is an image.

Procedure:
1. Remove the INSULATOR (4 pieces) and broken optical device (KEM-480AAA)
from LOADING ASSY.
2. Take photo of the barcode on new optical device (KEM- 480AAA) bottom side
by digital camera.

3. Assemble the INSULATOR (4 pieces) to new optical device (KEM-480AAA), fix

(Torque value: 2 kgf) it to LOADING ASSY with screw, and assemble this unit.
4. Drag & drop the taken photo by step 2 to “BDPRDec.exe”, and make the text
data (File name: BuData.txt).
5. Save the text data to USB memory.
6. Connect USB memory with side USB connector on this unit, and turn the power
on.

7. Press the [FUNCTION] button on the remote commander to select “BD/DVD”.

8. Press the buttons on the remote commander in order of [DISPLAY], [0], [2], [1],

https://electro-medical.blogspot.com/2016/02/sony-hbd-n890w-service-mode-test-mode.html[28/10/2020 10:01:12 πμ]

ELECTRONIC EQUIPMENT REPAIR CENTRE : SONY HBD-N890W - Service mode - Test mode – factory reset – laser pick up replacement procedure – how to eject the disc – Bluray player repair...

[SUBTITLE], and enter the service mode.

9. Press the buttons on the remote commander in order of [8], [1], [ENTER], and
execute “[1] Drive OP data Write”.
10. Turn the power off after writing the OP data.
11. Turn the power on, and enter the service mode again.
12. Press the buttons on the remote commander in order of [8], [7], [3], [ENTER],
and the dIOP value is displayed.
13. Confirm value is the following specification value, and turn the power off.
Specification value:
BD : ±3 mA
DVD/CD : ±3 mA
14. Turn the power on, confirm playback performance of the BD (BLX-104)/DVD
(HLX-513)/CD (HLX-A1).
15. Completely assemble this unit, and complete the repair.
MODEL IDENTIFICATION

Newer Post Home Older Post

Awesome Inc. theme. Powered by Blogger.

https://electro-medical.blogspot.com/2016/02/sony-hbd-n890w-service-mode-test-mode.html[28/10/2020 10:01:12 πμ]