ADDITIONAL BOTTOM T-BAR ADDITIONAL BOTTOM T-BAR

TO LAP BOTTOM BRC, ONLY TO LAP BOTTOM BRC, ONLY Mark Revision Date By
CL CL CL CL FULL YIELD LAP AT TRANSFER BEAM AREA AT TRANSFER BEAM AREA
L < L1 L1 L < L1 L1 (REFER TO SLAB DETAILS) (REFER TO SLAB DETAILS)
Notes :
EDGE BEAM EDGE BEAM
100 OR 12Ø
HOOK AND TOP MESH BEND DOWN SLAB WHICHEVER IS MAX. TOP MESH BEND DOWN SLAB
CL CL 50mm CROSS WIRE AT EXTERIOR RC WALL AT EXTERIOR RC BEAM

(MIN. 600)

(MIN. 600)
TO BE PROVIDED

0.15 L1

0.15 L1

100mm

100mm
MIN.

MIN.
TOP BAR TOP BAR
TYPICAL BRC LAPPING

300
100 OR 12Ø 100 OR 12Ø
WHICHEVER IS MAX. WHICHEVER IS MAX.
WITH CROSS WIRE WALL THICKNESS
BOTTOM MESH BEND UP 100 OR 12Ø
WHICHEVER IS MAX.
BOTTOM BAR AT EXTERIOR RC WALL BEAM WIDTH BOTTOM MESH BEND UP
NOTE : BRC LAPPING WITHOUT CROSS WIRE IS
70 TIMES BAR DIAMETER AT EXTERIOR RC BEAM
0.3 L1 0.3 L1 EXTERIOR RC WALL INTERIOR RC WALL

BOTTOM BAR
0.15 L1 40 Ø 40 Ø
(MIN. 600) (MIN. 600) (MIN. 600) 0.3 L1 0.3 L1 0.15 L1
(MIN. 600) (MIN. 600)

L2
EXTERIOR RC BEAM INTERIOR RC BEAM

TOP BAR
(MIN. 600)
TYPICAL SLAB BRC
NOTES ON BRC REINFORCEMENT :
ANCHORAGE TO RC WALLS

TOP BAR
TYPICAL SLAB BRC

TOP BAR
TOP BAR
1. ALL LAPPING OF BRC MESH REINFORCEMENT SHALL BE
TOP BAR

FULL YIELD LAP, UNLESS OTHERWISE INDICATED. EXCEPT FOR

TOP BAR
EDGE BEAM

BOTTOM BAR
L2

TOP BAR DISTRIBUTION STEEL OF TOP MESH REINFORCEMENT WHICH ANCHORAGE TO BEAMS
SHALL BE HALF YIELD LAP. FULL YIELD LAP SHALL BE

(MIN. 600)
DEFINED AS LAPPING OVER A LENGTH OF 2 WELDS PLUS 50mm.
EDGE BEAM

0.3 L1
TOP BAR
2. SHEARING STRENGTH OF WELDED CROSS WIRE SHALL BE
MINIMUM 50% OF THE YIELD STRENGTH OF THE MAIN BAR.

BOTTOM BAR CL 3. REINFORCEMENT LINE INDICATED HERE DENOTES MAIN STEEL

OF BRC. GENERALLY, FOR BOTTOM STEEL, MAIN STEEL SHALL
BE IN THE SHORTER SPAN, AND FOR TOP STEEL, MAIN STEEL 140mm (FIN.)
TOP BAR SHALL BE ALONG RESPECTIVE SPAN. SLAB REINFORCEMENT 140mm (FIN.)
INTERIOR BEAM BRICKWALL BRICKWALL
SLAB REINFORCEMENT

(SLAB THICKNESS)

(SLAB THICKNESS)

D
(MIN. 600)

T
0.15 L1

T
1
100 100 1
CL
TYPICAL CURTAILMENT OF 3T12 IN ADDITION TO REGULAR 3T12 IN ADDITION TO REGULAR
125
2-WAY SLAB REINFORCEMENT SLAB REINFORCEMENT ; LENGTH TO
BE 300mm (INCLUSIVE OF BEND) INTO FACES
SLAB REINFORCEMENT ; LENGTH
INTERIOR BEAM TO BE 300 mm (CRANKED)
(DETAIL B) OF BEAM/WALL.
(INCLUSIVE OF BEND) INTO FACES OF
TOP BAR
DETAIL 1 BEAM / WALL.
DETAIL 2
(DIMENSION OF HAUNCH TO REFER TO DETAILS)

TYPICAL CURTAILMENT OF TYPICAL DETAILS OF BRICKWALL ON SUSPENDED SLAB

1-WAY SLAB REINFORCEMENT
(DETAIL A)

550
600 750 600

DROP
(MAX.) (MAX.) T12-200
T12-200 SLAB TO DETAILS

125

125
T12-200 SLAB TO DETAILS T12-200
SLAB TO DETAILS BEAM TO DETAILS

BEAM TO DETAILS BEAM TO DETAILS

125
SLAB REINFORCEMENT R6 @ 200 C/C LINKS WHERE
NOTATION : THERE ARE NO TOP REINFORCEMENT
R1 TO HOLD THE TRIMMER BARS. T12-200
T : SLAB THICKNESS 600 T12-200

550
T/T : EQUAL THICKNESS T OF MAIN (MAX.)
AND HAUNCHED SLABS.
D : DROP HEIGHT
TYPICAL SECTIONAL DETAILS OF RC. LEDGES
AS1 : EQUIVALENT T-BAR OF BRC 1 100 100
R1 R1
AS2 : EQUIVALENT T-BAR OF BRC 2
A L1 : FULL-YIELD ANCHORAGE OF BRC 1
SLAB REINFORCEMENT
SLAB THICKNESS L2 : FULL-YIELD ANCHORAGE OF BRC 2
T/T

40Ø 40Ø
40Ø 40Ø
A AS1 AS2 SECTION 1-1 300 MAX. 1 T16 E/F 1 T10 E/F
ELECTRICAL CONDUIT SLAB REINFORCEMENT
DROP D. 450 MAX. 2 T16 E/F 1 T12 E/F TO DETAILS
BRC 2 L2 BRC 2 (TOP MESH,
D

SLAB THICKNESS
WHERE APPLICABLE)
600 MAX. * 2 T20 E/F 1 T16 E/F
A A R1 SLAB REINFORCEMENT Principal :
T

NOTES :
T

1
1 1. NO MORE THAN 1 OPENING GREATER THAN
2D BEAM/WALL 450mm PER SLAB PANEL IS PERMISSIBLE.
BRC 1
L1 MORE THAN 1 OPENING SHALL BE REFERED
BRC 1 TO THE ENGINEER FOR SPECIAL CONSIDERATION.
(BOTTOM MESH) 100
R1
PLACEMENT OF ELECTRICAL
TYPICAL PLAN VIEW SLAB REINFORCEMENT 2. OPENINGS MARKED * TO REFER TO ENGINEER
CONDUIT IN SLAB
SECTION A-A FOR CONFIRMATION BEFORE CONSTRUCTION.
OF HAUNCHED SLAB SECTION 2-2

40Ø A 40Ø 40Ø A 40Ø

40Ø A 40Ø

Project :
R1 R1 R1 R1
40Ø

40Ø

40Ø

R1 R1 BEAM/WALL

R2 R2 R2 R2 R2 R2

1 1 2 2 2 2
A

R2 R2 R2 R2 R2 R2 Drawing Title :

GENERAL NOTES -
0
0

0
60
60

60

TYPICAL SLAB REINFORCEMENT DETAIL

40Ø

40Ø

40Ø

R1 R1 R1

Consultants :
BEAM / WALL BEAM / WALL

OPENING AT CENTRAL PART OF SLAB OPENING AT EDGE OF SLAB OPENING AT CORNER OF SLAB R GCU Consultants (Johor) Sdn Bhd
No. 12-02, Jalan Molek 1/5C, Taman Molek,
TYPICAL DETAILS OF SLAB OPENINGS 81100 Johor Bahru, Johor Darul Takzim,
40Ø
40Ø Malaysia.
40Ø 20Ø BUT NOT
Tel : 07 - 350 7391 Fax : 07 - 350 7392
AS1 LESS THAN 300
AS2 BRC 2 40Ø 40Ø
(TOP MESH)
600 BRC 2 AS1 AS2 AS2 BRC 2
TO ARCHITECT'S

(TOP MESH) (TOP MESH)

150
200

DETAILS

200
300

(MIN.) 2T12
T

R8-200
D
T

T
T

I hereby certify that these works have been designed by me in accordance

with sound engineering practice and that I take full responsibility for the
100

design and proper performance of the same.

T
100

B/2 BRC 1
(BOTTOM MESH) RC SLAB
(MIN.) BRC 1 BRC 1
BEAM / WALL
1200 300
(BOTTOM MESH) (BOTTOM MESH)
RC BEAM THIS DRAWING IS COPYRIGHT
WHERE AVAILABLE
D 2D W 2D D
THIS DRAWING OR ANY PART OF IT SHALL NOT BE REPRODUCED IN ANY
BEAM/WALL
WIDTH TYPICAL SLAB DETAILS (2) TYPICAL KERB DETAILS FORM WITHOUT THE WRITTEN PERMISSION OF THE ENGINEER.
AT SCUPPER DRAIN/TRENCHES CONTRACTOR MUST CHECK ALL DIMENSIONS ON SITE. ANY DISCREPANCIES
TYPICAL SLAB DETAILS (1) (FOR D LESS THAN T) MUST BE REPORTED IMMEDIATELY TO THE ENGINEER BEFORE PROCEEDING
(UNLESS OTHERWISE INDICATED)
AT SCUPPER DRAIN Design By : Check By :
NOTATION : HBS LKM
( SCUPPER DRAIN = 300mm WIDE x 150mm HT. )
T : SLAB THICKNESS
NOTATION : D : DEPTH OF TRENCH Drawn By : CAD FILE :
AS1 : EQUIVALENT T-BAR OF BRC 1 W : WIDTH OF TRENCH MKI
AS1 : EQUIVALENT T-BAR OF BRC 1
C-GCUJ-JJ036-SD-4000-GN-006-A
AS2 : EQUIVALENT T-BAR OF BRC 2
AS2 : EQUIVALENT T-BAR OF BRC 2
Date: Scale :
SEPT 2017 AS SHOWN

Drawing No :
P/GCUJ/JJ036/SD/4000/GN/006 A
Z:\1.1 PROJECT TCL\JJ036 COUNTRY GARDEN FOREST CITY\DRAWING\OUTGOING\PRELIMINARY\11 BRICK FACTORY\GENERAL NOTES (RC)\C-GCUJ-JJ036-SD-4000-GN-006-A.DWG ; 03-Oct-17 ; 12:46:46 ; PLOTTED BY : OWNER ; PLOT SCALE : 1:2