Scribd
Upload
64 views

Chapter 6 Analysis of Structures: Connected at Their Extremities Only. The Members Being

The document discusses methods for analyzing structures like trusses, frames, and machines. It describes trusses as structures made of straight members connected at their ends. Simple trusses have a set number of members based on the number of joints. Forces in a truss can be determined using the method of joints or method of sections. Frames contain multi-force members and their analysis involves considering the entire frame as a free body and then its individual members. Machines are designed to transmit or modify forces and always contain moving parts.

Uploaded by

BELAL ALSUBARI
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
64 views

Chapter 6 Analysis of Structures: Connected at Their Extremities Only. The Members Being

The document discusses methods for analyzing structures like trusses, frames, and machines. It describes trusses as structures made of straight members connected at their ends. Simple trusses have a set number of members based on the number of joints. Forces in a truss can be determined using the method of joints or method of sections. Frames contain multi-force members and their analysis involves considering the entire frame as a free body and then its individual members. Machines are designed to transmit or modify forces and always contain moving parts.

Uploaded by

BELAL ALSUBARI
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

Chapter 6 ANALYSIS OF STRUCTURES

A truss is a structure consisting of straight members


connected at their extremities only. The members being
slender and unable to support lateral loads, all the loads must
be applied at the joints; a truss may thus be assumed to
consist of pins and two-force members.

pin two-force member pin


B

A C

A truss is said to be rigid if it is designed in such a way that


it will not greatly deform or collapse under a small load. A
triangular truss consisting of three members connected at
three joints is clearly a rigid truss.
D
B B

A C A C

A truss obtained by adding two new members to the first one


and connecting them to a new joint (D ) will also be rigid.
Trusses obtained by repeating this procedure are called simple
trusses. We may check that in a simple truss the total number
of members is m = 2n - 3, where n is the total number of joints.
The forces in the various members of a B
truss can be determined by the method
of joints. First, the reactions at the supports
can be obtained by considering the entire
truss as a free body. The free-body A C
diagram of each pin is then drawn, showing
the forces exerted on the pin by the members
or supports it connects. Since the members are straight two-
force members, the force exerted by a member on the pin is
directed along that member, and only the magnitude of the force
is unknown. It is always possible in the case of a simple truss to
draw the free-body diagrams of the pins in such an order that only
two unknown forces are included in each diagram. These forces
can be obtained from the corresponding two equilibrium
equations or - if only three forces are involved - the corresponding
force triangle.
T Tension (T) T
B

Compression (C)

A C C C

If the force exerted by a member on a pin is directed toward that


pin, the member is in compression ; if it is directed away from
the pin, the member is in tension. The analysis of a truss is
sometimes expedited by first recognizing joints under special
loading conditions (involving zero-force members, for
example). The method of joints can also be extended to the
analysis of three-dimensional or space trusses.
P1 P2 P3
n G
B D
A

C E
n

The method of sections is usually preferred to the method


of joints when the force in only one member - or very few
members - of a truss is desired. To determine the force in
member BD of the truss shown, we pass a section through
members BD, BE, and CE, remove these members, and use
the portion ABC of the truss as a free body.
P1 P2 P1 P2 P3
n G
B FBD B D
A A
FBE
C E C E
FCE n

Writing ΣME = 0, we determine the magnitude of FBD, which


represents the force in member BD. A positive sign indicates
that the member is in tension; a negative sign indicates that
it is in compression.
The method of sections is particularly useful in the analysis of
compound trusses (trusses which cannot be constructed
from the basic triangular truss, but which can be obtained by
rigidly connecting several simple trusses). If the component
trusses have been properly connected (e.g., one pin and one
link, or three nonconcurrent and nonparallel links) and if the
resulting structure is properly supported (e.g., one pin and one
roller), the compound truss is statically determinate, rigid, and
completely constrained. The following necessary - but not
sufficient - condition is then
P1 P2
satisfied: m + r = 2n, where
m is the number of members, B FBD
r is the number of unknowns
representing the reactions at the FBE
supports, and n is the number of joints. C E
FCE
Frames and machines are
structures which contain
multiforce members, i.e., A B C D
members acted upon by three
or more forces. Frames are
designed to support loads and
are usually stationary, fully M
constrained structures.

Machines are designed to transmit or modify forces and


always contain moving parts.
To analyze a frame, we
first consider the entire
frame as a free body and A Dx
B C D
write three equilibrium Dy
equations. If the frame
remains rigid when
detached from its supports, M
the reactions involve only Ex
three unknowns and may Ey
be determined from these
equations. On the other hand, if the frame ceases to be rigid
when detached from its supports, the reactions involve more
than three unknowns and cannot be completely determined from
the equilibrium equations of the frame.
Then dismember the frame and identify the members as either
two-force members or multiforce members; pins are assumed to
form an integral part of one of the members they connect.

B
Dx
B
A B C D
B Dy

M We draw the free-body diagram of each of


Ex the multiforce members, noting that when two
Ey multiforce members are connected to the
same two-force member, they are acted upon
by that member with equal and opposite forces of unknown
magnitude but known direction. When two multiforce
members are connected by a pin, they exert on each other
equal and opposite forces of unknown direction, which
should be represented by two unknown components.
The equilibrium equations obtained from the free-body
diagrams of the multiforce members can then be solved
for the various internal forces. The equilibrium equations
can also be used to complete the determination of the
reactions at the supports. Actually, if the frame is
statically determinate and rigid, the free-body
diagrams of the multiforce members could provide as
many equations as there are unknown forces. However,
as suggested above, it is advisable to first consider the
free-body diagram of the entire frame to minimize the
number of equations that must be solved simultaneously.
To analyze a machine, we dismember it and, following the
same procedure as for the frame, draw the free-body diagram of
each of the multiforce members. The corresponding equilibrium
equations yield the output forces exerted by the machine in
terms of the input forces applied to it, as well as the internal
forces at various connections.

You might also like