Technical Data

1756 ControlLogix and GuardLogix Controllers

ControlLogix Controller Catalog Numbers 1756-L61, 1756-L62, 1756-L63, 1756-L63XT, 1756-L64, 1756-L65
1756-L71, 1756-L72, 1756-L73, 1756-L73XT, 1756-L74, 1756-L75
1756-L71K, 1756-L72K, 1756-L73K, 1756-L74K, 1756-L75K
1756-L81E, 1756-L82E, 1756-L83E, 1756-L84E, 1756-L85E,
1756-L81EK, 1756-L82EK, 1756-L83EK, 1756-L84EK, 1756-L85EK

GuardLogix Controller Catalog Numbers 1756-L61S, 1756-L62S, 1756-L63S, 1756-LSP

1756-L71S, 1756-L71SK, 1756-L72S, 1756-L72SK, 1756-L73S, 1756-L73SK, 1756-L7SP,
1756-L7SPK, 1756-L73SXT, 1756-L7SPXT
1756-L81ES, 1756-L81ESK, 1756-L82ES,1756-L82ESK, 1756-L83ES, 1756-L83ESK,
1756-L84ES, 1756-L84ESK, 1756-L8SP, 1756-L8SPK

Armor ControlLogix Catalog Numbers 1756-L72EROM, 1756-L73EROM

Armor GuardLogix Catalog Numbers 1756-L72EROMS, 1756-L73EROMS
ControlLogix Redundancy Catalog Numbers 1756-RM2, 1756-RM2XT

Topic Page
1756 ControlLogix Controllers 2
1756 ControlLogix-XT Controllers 13
1756 GuardLogix Controllers 17
1756 GuardLogix-XT Controllers 29
1756 Armor ControlLogix and Armor GuardLogix Controllers 32
Controller Compatibility 36
ControlLogix Redundancy 39
ControlLogix Controller Accessories 42
1756 ControlLogix and GuardLogix Controllers

1756 ControlLogix Controllers

The ControlLogix® controller provides a scalable controller solution that is capable of addressing many I/O points. You
can place the ControlLogix controller into any slot of a ControlLogix I/O chassis, and install multiple controllers in the
same chassis.

ControlLogix controllers can monitor and control I/O across the ControlLogix backplane, and over network links. The
ControlLogix 5580 controllers have an embedded Ethernet port for a direct connection to Ethernet-enabled devices and
networks, and also support communication interface modules in the local chassis. To provide communication for
ControlLogix 5570 or ControlLogix 5560 controllers, install the appropriate communication interface module into the
local chassis.

ControlLogix 5580 and ControlLogix 5570 controllers are available with a conformal coating. A conformal coating
provides a layer of protection against contaminants and humidity to help protect the assembly and extend product life in
harsh, corrosive environments. Products with a conformal coating have a ‘K’ suffix at the end of the catalog number.

1756 ControlLogix Controller Page

ControlLogix 5580 Controllers Features and Specifications 3
ControlLogix 5570 Controllers Features and Specifications 7
ControlLogix 5560 Controllers Features and Specifications 10

2 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

ControlLogix 5580 Controllers Features and Specifications

1756-L81E, 1756-L82E, 1756-L83E, 1756-L84E, 1756-L85E,

Feature
1756-L81EK 1756-L82EK 1756-L83EK 1756-L84EK 1756-L85EK
32 tasks
Controller tasks 1000 programs/task
Local I/O event triggers: No limit
1 port USB(3)
Built-in communication ports
Embedded Ethernet port
USB 2.0
USB port communication Full speed (12 Mbps)
Programming, configuration, firmware update, and on-line edits only
Ethernet performance 10/100/1000 Mbps
I/O: 128,000
Packet Rate Capacity (packets/second)(1)
HMI/MSG: 1000
• EtherNet/IP™
• ControlNet™
• DeviceNet™
Communication options • Data Highway Plus™
• Remote I/O
• SynchLink™
• Third-party process and device networks
60 nodes(5) 80 nodes(5) 100 nodes(4) 150 nodes(5)
EtherNet/IP nodes supported, max(2) 300 nodes(7)
100 nodes(6) 175 nodes(6) 250 nodes(6) 250 nodes(6)
• ControlLogix 5580 Controllers front EtherNet/IP port. See ‘EtherNet/IP nodes supported, max’ in this table.
• 256 EtherNet/IP; 128 TCP (1756-EN2x)
Network connections, per network module located • 128 EtherNet/IP; 64 TCP (1756-ENBT)
in the local chassis • 100 ControlNet (1756-CN2/A)
• 40 ControlNet (1756-CNB/D, 1756-CNB/E)
• 128 ControlNet (1756-CN2/B)
Controller redundancy —
Integrated motion • Integrated Motion on the EtherNet/IP network
• Relay Ladder Logic (RLL)
• Structured Text
Programming languages • Function Block Diagram
• Sequential Function Chart (SFC)
(1) I/O numbers are maximums; they assume no HMI/MSG. HMI/MSG numbers are maximums, they assume no I/O. Packet rates vary depending on packet size. For more details, see Troubleshoot EtherNet/IP Application Technique,
publication ENET-AT003, and the EDS file for a specific catalog number.
(2) A node is an EtherNet/IP device that you add directly to the I/O configuration, and counts toward the node limits of the controller. For more information on EtherNet/IP nodes, see the ControlLogix 5580 Controllers User Manual,
publication1756-UM543.
(3) The USB port is intended for temporary local programming purposes only and not intended for permanent connection. Do not use the USB port in hazardous locations.
(4) With Studio 5000 Logix Designer® Application Version 28 and Version 29.
(5) With Studio 5000 Logix Designer Application Version 29.
(6) With Studio 5000 Logix Designer Application Version 30 or greater.
(7) With Studio 5000 Logix Designer Application Version 28 or greater.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 3

1756 ControlLogix and GuardLogix Controllers

Technical Specifications - ControlLogix 5580 Controllers

1756-L81E, 1756-L82E, 1756-L83E, 1756-L84E, 1756-L85E,
Attribute
1756-L81EK 1756-L82EK 1756-L83EK 1756-L84EK 1756-L85EK
User memory 3 MB 5 MB 10 MB 20 MB 40 MB
Digital I/O, max 128,000
Analog I/O, max 4000
Total I/O, max 128,000
Optional nonvolatile memory storage 2 GB Secure Digital Card (1784-SD2), ships pre-installed in the controller
Energy storage module Embedded in controller, nonremovable
Current draw @ 1.2V DC 5.0 mA
Current draw @ 5.1V DC 1.20 A
Power dissipation 6.2 W
Thermal dissipation 21.2 BTU/hr
50V (continuous), Basic Insulation type, USB port to backplane, Ethernet port to backplane, and USB port to Ethernet port
Isolation voltage Type tested at 1000V AC for 60 seconds
Weight, approx 0.394 kg (.868 lb)
Slot width 1
Module location Chassis-based, any slot
Chassis 1756-A4, 1756-A4K, 1756-A7, 1756-A7K, 1756-A10, 1756-A10K, 1756-A13, 1756-A13K,1756-A17, 1756-A17 K Series B, Series C
1756-PA50, 1756-PA72, 1756-PA72K, 1756-PA75, 1756-PA75K, 1756-PB50, 1756-PB72, 1756-PB72K, 1756-PB75, 1756-PB75K,
Power supply, standard 1756-PH75, 1756-PC75
Power supply, redundant 1756-PA75R, 1756-PA75RK, 1756-PB75R, 1756-PB75RK, 1756-PSCA2, 1756-PSCA2K
3 - on USB port
Wire category(1)
2 - on Ethernet ports
Ethernet connections:
Wire size
Ethernet cabling and installation according to IEC 61918 and IEC 61784-5-2
North American temperature code T4
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) Use this conductor category information to plan conductor routing. See Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

4 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - ControlLogix 5580 Controllers

1756-L81E, 1756-L82E, 1756-L83E, 1756-L84E, 1756-L85E, 1756-L81EK, 1756-L82EK,
Attribute
1756-L83EK, 1756-L84EK, 1756-L85EK
Temperature, operating Chassis series C: 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F)
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), Chassis series B: 0 °C < Ta < +50 °C (+32 °F < Ta < +122 °F)
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), Chassis series B and C: -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Chassis series C: 60 °C (140 °F)
Temperature, surrounding air, max
Chassis series B: 50 °C (122 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
EFT/B Immunity ±2 kV at 5 kHz on Ethernet ports
IEC 61000-4-4
Surge Transient Immunity
±2 kV line-earth (CM) on Ethernet ports
IEC 61000-4-5
Conducted RF Immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
IEC 61000-4-6

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 5

1756 ControlLogix and GuardLogix Controllers

Certifications - ControlLogix 5580 Controllers

Certification(1) 1756-L81E, 1756-L81EK, 1756-L82E, 1756-L82EK, 1756-L83E, 1756-L83EK, 1756-L84E, 1756-L84EK, 1756-L85E, 1756-L85EK
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
CSA Certified Process Control Equipment. See CSA File LR54689C.
CSA
CSA Certified Process Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations. See CSA File LR69960C.
FM FM Approved Equipment for use in Class I Division 2 Group A,B,C,D Hazardous Locations
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO13ATEX1325026X
IECEx System, compliant with:
• IEC 60079-15; Potentially Explosive Atmospheres, Protection “n”
IECEx • IEC 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 14.0008X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
EtherNet/IP ODVA conformance tested to EtherNet/IP specifications
(1) See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

6 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

ControlLogix 5570 Controllers Features and Specifications

Feature 1756-L71, 1756-L71K, 1756-L72, 1756-L72K, 1756-L73, 1756-L73K, 1756-L74, 1756-L74K, 1756-L75, 1756-L75K
• 32 tasks
Controller tasks • 100 programs/task
• Event tasks: all event triggers
Built-in communication ports 1 port USB(2)
• EtherNet/IP
• ControlNet
• DeviceNet
Communication options • Data Highway Plus
• Remote I/O
• SynchLink
• Third-party process and device networks
USB port communication Programming, configuration, firmware update, and on-line edits only
Controller connections supported, max(1) 500
• 100 ControlNet (1756-CN2/A)
• 40 ControlNet (1756-CNB/D, 1756-CNB/E)
Network connections, per network module • 128 ControlNet (1756-CN2/B)
• 256 EtherNet/IP; 128 TCP (1756-EN2x)
• 128 EtherNet/IP; 64 TCP (1756-ENBT)
Controller redundancy Full support
• SERCOS interface
Integrated motion • Analog options (encoder input, LDT input, SSI input)
• Integrated Motion on the EtherNet/IP network
• Relay Ladder
• Structured Text
Programming languages • Function Block Diagram
• Sequential Function Chart (SFC)
(1) ControlLogix 5570 controllers use connections to establish communication links between devices. For more information on how to use and calculate connections, see the ControlLogix System User Manual, publication
1756-UM001.
(2) The USB port is intended for temporary local programming purposes only and not intended for permanent connection. Do not use the USB port in hazardous locations.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 7

1756 ControlLogix and GuardLogix Controllers

Technical Specifications - ControlLogix 5570 Controllers

Attribute 1756-L71, 1756-L71K 1756-L72, 1756-L72K 1756-L73, 1756-L73K 1756-L74, 1756-L74K 1756-L75, 1756-L75K
User memory 2 MB 4 MB 8 MB 16 MB 32 MB
I/O memory 0.98 MB
1 GB (1784-SD1 ships with every controller)
Optional nonvolatile memory storage
2 GB (1784-SD2)
Digital I/O, max 128,000
Analog I/O, max 4000
Total I/O, max 128,000
• 1756-ESMCAP, 1756-ESMCAPK capacitor energy storage module (removable, ships installed with every controller)
• 1756-ESMNSE, 1756-ESMNSEK capacitor energy storage module (removable, no residual WallClockTime power backup)
Energy storage module • 1756-ESMNRM, 1756-ESMNRMK capacitor energy storage module (nonremovable, helps prevent USB connection and SD card use to
help secure the controller)
Current draw @ 1.2V DC 5 mA
Current draw @ 5.1V DC 800 mA
Power dissipation 2.5 W
Thermal dissipation 8.5 BTU/hr
30V (continuous), basic insulation type, USB port-to-system
Isolation voltage Type tested at 500V AC for 60 s
USB port(1) USB 2.0, full speed (12 Mbps)
Weight, approx 0.25 kg (0.55 lb)
Slot width 1
Module location Chassis-based, any slot
Chassis 1756-A4, 1756-A4K, 1756-A7, 1756-A7K, 1756-A10, 1756-A10K, 1756-A13, 1756-A13K,1756-A17, 1756-A17 K
1756-PA50, 1756-PA72, 1756-PA72K, 1756-PA75, 1756-PA75K, 1756-PB50, 1756-PB72, 1756-PB72K, 1756-PB75, 1756-PB75K,
Power supply, standard 1756-PH75
Power supply, redundant 1756-PA75R, 1756-PA75RK, 1756-PB75R, 1756-PB75RK,1756-PSCA2, 1756-PSCA2K
Wire category(2) 3 - on USB port
North American temperature code T4A
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) The USB port is intended for temporary local programming purposes only and not intended for permanent connection. Do not use the USB port in hazardous locations.
(2) Use this conductor category information to plan conductor routing. See Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

8 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - ControlLogix 5570 Controllers

1756-L71, 1756-L71K, 1756-L72, 1756-L72K, 1756-L73, 1756-L73K, 1756-L74K, 1756-L74,
Attribute
1756-L75, 1756-L75K
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 60 °C (140 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g (45 g with SD card installed)
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
Conducted RF Immunity Not applicable: USB is a temporary programming port.
IEC 61000-4-6

Certifications - ControlLogix 5570 Controllers

Certification(1) 1756-L71, 1756-L71K, 1756-L72, 1756-L72K, 1756-L73, 1756-L73K, 1756-L74, 1756-L74K, 1756-L75, 1756-L75K
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
EN 60079-0; General Requirements
Ex EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
II 3 G Ex nA IIC T4 Gc
DEMKO13ATEX1325026X
IECEx System, compliant with:
IEC 60079-0; General Requirements
IECEx IEC 60079-15; Potentially Explosive Atmospheres, Protection “n”
II 3 G Ex nA IIC T4 Gc
IECEx UL 14.0008X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 9

1756 ControlLogix and GuardLogix Controllers

ControlLogix 5560 Controllers Features and Specifications

Feature 1756-L61, 1756-L62, 1756-L63, 1756-L63XT, 1756-L64, 1756-L65

• 32 tasks
Controller tasks • 100 programs/task
• Event tasks: all event triggers
Built-in communication ports 1 port RS-232 serial
• EtherNet/IP
• ControlNet
• DeviceNet
Communication options • Data Highway Plus
• Remote I/O
• SynchLink
• Third-party process and device networks
• ASCII
• DF1 full/half-duplex
Serial port communication • DF1 radio modem
• DH-485
• Modbus via logic
Controller connections supported, max(1) 250
• 100 ControlNet (1756-CN2/A)
• 40 ControlNet (1756-CNB/D, 1756-CNB/E)
Network connections, per network module • 128 ControlNet (1756-CN2/B)
• 256 EtherNet/IP; 128 TCP (1756-EN2x)
• 128 EtherNet/IP; 64 TCP (1756-ENBT)
Controller redundancy Full support
• SERCOS interface
Integrated motion • Analog options (encoder input, LDT input, SSI input)
• Integrated Motion on the EtherNet/IP network
• Relay Ladder
• Structured Text
Programming languages • Function Block Diagram
• Sequential Function Chart (SFC)
(1) ControlLogix 5560 controllers use connections to establish communication links between devices. For more information on connections, see the ControlLogix System User Manual, publication 1756-UM001.

IMPORTANT Scan time for a project that is loaded in a 1756-L64 or 1756-L65 controller can be slower than for the same project loaded in one
of the other 1756-L6x controllers. For instruction execution times, see the Logix5000 Controllers Instruction Execution Time and
Memory Use Reference Manual, publication 1756-RM087.

10 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Technical Specifications - ControlLogix 5560 Controllers

Attribute 1756-L61 1756-L62 1756-L63 1756-L64 1756-L65
User memory 2 MB 4 MB 8 MB 16 MB 32 MB

I/O memory 478 KB

Optional nonvolatile memory storage 128 MB (1784-CF128)
Digital I/O, max 128,000
Analog I/O, max 4000
Total I/O, max 128,000
Series A: 1756-BA1, 1756-BATM, 1756-BATA
Replacement battery(1) 1756-BA2 (0.50 g Lithium)
Series B: 1756-BA2
Current draw @ 5.1V DC 1200 mA
Current draw @ 24V DC 14 mA
Power dissipation 3.5 W
Thermal dissipation 11.9 BTU/hr
30V (continuous), basic insulation type, RS-232 port to system
Isolation voltage Type tested at 720V DC for 60 s
Serial cables 1756-CP3 or 1747-CP3, right angle connector to controller, straight to serial port, 3 m (9.84 ft)
Series A: 0.32 kg (0.71 lb)
Weight, approx Series B: 0.35 kg (0.78 lb)
Slot width 1
Module location Chassis-based, any slot
Chassis 1756-A4, 1756-A7, 1756-A10, 1756-A13, 1756-A17
Power supply, standard 1756-PA50, 1756-PA72, 1756-PA75, 1756-PB50, 1756-PB72, 1756-PB75
Power supply, redundant 1756-PA75R, 1756-PB75R, 1756-PSCA2
Wire category(2) 2 - on RS-232 port
North American temperature code T4A
IEC temperature code T4
Enclosure type rating None (open-style)
(1) For Australian Mining certification applications, only a series A controller and a 1756-BA1 battery can be used. For more information, contact your local distributor or sales office.
(2) Use this conductor category information to plan conductor routing as described in the system level installation manual. See the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 11

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - ControlLogix 5560 Controllers

Attribute 1756-L61, 1756-L62, 1756-L63, 1756-L64, 1756-L65
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0…60 °C (32 …140 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, storage
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 60 °C (140 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions
CISPR 11 Class A
IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
EFT/B immunity ±4 kV at 5 kHz on RS-232 port
IEC 61000-4-4
Surge transient immunity ±2 kV line-earth (CM) on RS-232 port
IEC 61000-4-5
Conducted RF immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
IEC 61000-4-6

Certifications - ControlLogix 5560 Controllers

Certification(1) 1756-L61, 1756-L62, 1756-L63, 1756-L64, 1756-L65
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
CSA Certified Process Control Equipment. See CSA File LR54689C.
CSA
CSA Certified Process Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations. See CSA File LR69960C.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
• EN60079-0; General Requirements
Ex • II 3 G Ex nA IIC T4 X
• LCIE01ATEX6020X
IMPORTANT: The 1756-L64 and 1756-L65 controllers do not have this certification.
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
FM FM Approved Equipment for use in Class I Division 2 Group A,B,C,D Hazardous Locations
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

12 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

1756 ControlLogix-XT Controllers

The ControlLogix-XT™ controllers function in the same way as the traditional ControlLogix controllers.
The ControlLogix-XT products include control and communication system components that are conformally coated
for extended protection in harsh, corrosive environments:
• When used with FLEX I/O-XT™ products, the ControlLogix-XT system can withstand temperature ranges of -
20…+70 °C (-4…+158 °F).
• When used independently, the ControlLogix-XT system can withstand temperature ranges of -25…+70 °C (-
13…+158 °F).
• Customers who previously used the LXT chassis should now migrate to the K version of the chassis.

1756-L73XT ControlLogix Controller Specifications

Technical Specifications - 1756-L73XT ControlLogix Controller
Attribute 1756-L73XT
User memory 8 MB
I/O memory 0.98 MB
1 GB (1784-SD1 ships with every controller)
Optional nonvolatile memory 2 GB (1784-SD2)
Digital I/O, max 128,000
Analog I/O, max 4000
Total I/O, max 128,000
Replacement battery —
• 1756-ESMCAPXT capacitor energy storage module (removable, ships installed with every controller)
• 1756-ESMNSEXT capacitor energy storage module (removable, no residual WallClockTime power backup)
Energy storage modules • 1756-ESMNRMXT capacitor energy storage module (nonremovable, helps prevent USB connection and SD card use to help secure the
controller)
Current draw @ 5.1V DC 800 mA
Current draw @ 1.2V DC 5 mA
Power dissipation 2.5 W
Thermal dissipation 8.5 BTU/hr
30V (continuous), basic insulation type, USB port to backplane
Isolation voltage Type tested at 500V AC for 60 s
USB port(1) USB 2.0, full speed (12 Mbps)
Weight, approx 0.25 kg (0.55 lb)
Slot width 1
Module location Chassis-based, any slot
1756-A7XT, 1756-A10XT
Chassis
For low temperature applications only, use 1756-A4K, 1756-A7K, 1756-A10K, 1756-A13K, 1756-A17K
Power supply, standard 1756-PAXT, 1756-PA30XT, 1756-PBXT, 1756-PB30XT
Power supply, redundant None
(2)
Wire category 3 - on USB ports
North American temperature code T4A
IECEx temperature code T4
ATEX temperature code T4
Enclosure type rating None (open-style)
(1) The USB port is intended for temporary local programming purposes only and not intended for permanent connection. Do not use the USB port in hazardous locations.
(2) Use this conductor category information to plan conductor routing. See the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 13

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-L73XT ControlLogix Controller

Attribute 1756-L73XT
Temperature, operating -25 °C < Ta < +70 °C (-13 °F < Ta < +158 °F)
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), When using a 1756-A7LXT chassis, surrounding air temperature range is
IEC 60068-2-14 (Test Nb, Operating Thermal Shock) -25 °C < Ta < +60 °C (-13 °F < Ta < +140 °F) even when using an ‘XT’ controller.

Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 70 °C (158 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock) (45 g with SD card installed)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
Conducted RF Immunity Not applicable: USB is a temporary programming port.
IEC 61000-4-6

Certifications - 1756-L73XT ControlLogix Controller

Certification(1) 1756-L73XT
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61000-6-4; Industrial Emissions
CE • EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO13ATEX1325026X
IECEx System, compliant with:
• IEC 60079-0; General Requirements
IECEx • IEC 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 14.0008X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

14 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

1756-L63XT ControlLogix Controller Specifications

Technical Specifications - 1756-L63XT Controller

Attribute 1756-L63XT
User memory 8 MB
I/O memory 478 KB
Optional nonvolatile memory storage 128 MB (1784-CF128)
Digital I/O, max 128,000
Analog I/O, max 4000
Total I/O, max 128,000
Replacement battery 1756-BA2
Current draw @ 5.1V DC 1200 mA
Current draw @ 24V DC 14 mA
Power dissipation 3.5 W
Thermal dissipation 11.9 BTU/hr
30V (continuous), basic insulation type, RS-232 port to system
Isolation voltage Type tested at 720V DC for 60 s
Serial cables 1756-CP3 or 1747-CP3, right angle connector to controller, straight to serial port, 3 m (9.84 ft)
Weight, approx 0.35 kg (0.78 lb)
Slot width 1
Module location Chassis-based, any slot
1756-A7XT, 1756-A10XT
Chassis
For low temperature applications only, use 1756-A4K, 1756-A7K, 1756-A10K, 1756-A13K, 1756-A17K
Power supply, standard 1756-PAXT, 1756-PA30XT, 1756-PBXT, 1756-PB30XT
Power supply, redundant None
Wire category(1) 2 - on RS-232 port
North American temperature code T4A
IEC temperature code T4
Enclosure type rating None (open-style)
(1) Use this conductor category information to plan conductor routing as described in the system level installation manual. See the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 15

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-L63XT Controller

Attribute 1756-L63XT
Temperature, operating -25…+70 °C (-13…+158 °F)
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), When using a 1756-A7LXT chassis, surrounding air temperature range is -25…+60 °C (-13…+140 °F)
IEC 60068-2-14 (Test Nb, Operating Thermal Shock) even when using an ‘XT’ controller

Temperature, storage
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 70 °C (158 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions
Group 1, Class A
CISPR 11
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
EFT/B immunity ±4 kV at 5 kHz on RS-232 port
IEC 61000-4-4
Surge transient immunity ±2 kV line-earth (CM) on communication ports
IEC 61000-4-5
Conducted RF immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
IEC 61000-4-6

Certifications - 1756-L63XT Controller

Certification(1) 1756-L63XT
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61000-6-4; Industrial Emissions
CE • EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection ’n’
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 X
• LCIE01ATEX6020X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

16 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

1756 GuardLogix Controllers

GuardLogix 5580 Controller with Safety Partner GuardLogix 5570 Controller with Safety Partner

A GuardLogix® controller is a ControlLogix controller that also provides the ability to perform safety functions. You
must use a primary safety controller and a safety partner to achieve up to SIL CL 3/PLe/Cat. 4. A major benefit of this
system is that it is still one project, safety and standard together. The safety partner is a part of the system, is automatically
configured, and requires no user setup.

With the introduction of the GuardLogix 5580 controller, users can achieve up to SIL 2/PLd (Category 3) with a single
controller and the use of the safety task and safety I/O.

During development, safety and standard have the same rules; multiple programmers, online editing, and forcing are all
allowed. Once the safety system is validated and the safety signature applied, safety memory is protected, the safety logic
cannot be modified, and all safety functions operate with SIL integrity. If the safety partner is present, the safety integrity
will be SIL3. If no safety partner is present, the safety integrity will be SIL2.

On the standard side of the GuardLogix controller, all functions operate like a regular Logix controller. Thus, online
editing, forcing, and other activities are all allowed.

With this level of integration, safety memory can be read by standard logic and external devices, like HMIs or other
controllers, minimizing the need to condition safety memory for use elsewhere. The result is easy system-wide
integration and the ability to display safety status on displays or marquees. Use Guard I/O™ modules for field device
connectivity on Ethernet or DeviceNet networks, and for safety interlocking between GuardLogix controllers use
Ethernet or ControlNet networks. Multiple GuardLogix controllers can share safety data for zone to zone interlocking,
or one GuardLogix controller can use remote distributed safety I/O between different cells/areas.

1756 GuardLogix controllers are available with a conformal coating. The conformal coating provides a layer of
protection against contaminants and humidity to help protect the assembly and extend product life in harsh, corrosive
environments. Products with a conformal coating have a ‘K’ suffix at the end of the catalog number.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 17

1756 ControlLogix and GuardLogix Controllers

In addition to the standard features of a ControlLogix controller, the GuardLogix controller has these safety-related
features.
Features - GuardLogix Controllers
1756-L61S, 1756-L62S, 1756-L63S, 1756-L71S, 1756-L72S,
1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES,
Feature 1756-L73S, 1756-L73SXT, 1756-L71SK, 1756-L72SK,
1756-L81ESK, 1756-L82ESK, 1756-L83ESK, 1756-L84ESK
1756-L73SK
Standard and safety
• EtherNet/IP
Safety communication options • ControlNet
• DeviceNet
• GuardLogix 5580 Controllers front EtherNet/IP port. See ‘EtherNet/IP
• 100 ControlNet (1756-CN2/A) nodes supported, max’ in this table.
• 40 ControlNet (1756-CNB/D, 1756-CNB/E) • 256 EtherNet/IP; 128 TCP (1756-EN2x)
Network connections, per • 128 ControlNet (1756-CN2/B) • 128 EtherNet/IP; 64 TCP (1756-ENBT)
network module • 256 EtherNet/IP; 128 TCP (1756-EN2x) • 100 ControlNet (1756-CN2/A)
• 128 EtherNet/IP; 64 TCP (1756-ENBT) • 40 ControlNet (1756-CNB/D, 1756-CNB/E)
• 128 ControlNet (1756-CN2/B)
1756-L81ES, 1756-L81ESK: 100 nodes
EtherNet/IP nodes supported, 1756-L82ES, 1756-L82ESK: 175 nodes
—
max(1) 1756-L83ES, 1756-L83ESK: 250 nodes
1756-L84ES, 1756-L84ESK: 250 nodes
Controller redundancy Not supported
• Relay Ladder Logic (RLL)
• Structured Text
Programming languages • Function Block Diagram
• Sequential Function Chart (SFC)
• Safety Task supports only RLL and the additional safety application instructions
(1) A node is an EtherNet/IP device that you add directly to the I/O configuration, and counts toward the node limits of the controller. For more information on EtherNet/IP nodes, see the ControlLogix 5580 Controllers and
GuardLogix 5580 Controllers User Manual, publication1756-UM543.

Safety Partners
Primary Controller Safety Partner
1756-L61S, 1756-L62S, 1756-L63S 1756-LSP
1756-L71S, 1756-L71SK, 1756-L72S,1756-L72SK, 1756-L73S,1756-L73SK 1756-L7SP, 1756-L7SPK
1756-L73SXT 1756-L7SPXT
1756-L81ES, 1756-L81ESK, 1756-L82ES, 1756-L82ESK, 1756-L83ES, 1756-L83ESK, 1756-L84ES, 1756-L84ESK 1756-L8SP, 1756-L8SPK

18 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

GuardLogix 5580 Controllers Features and Specifications

1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES, 1756-L8SP,

Feature
1756-L81ESK 1756-L82ESK 1756-L83ESK 1756-L84ESK 1756-L8SPK
31 standard tasks, 1 safety task
Controller tasks 1000 programs/task —
Local I/O event triggers: No limit
1 port USB(3)
Built-in communication ports —
Embedded Ethernet port
USB 2.0
USB port communication Full speed (12 Mbps) —
Programming, configuration, firmware update, and on-line edits only
Ethernet performance 10/100/1000 Mbps —
I/O: 128,000
Packet Rate Capacity (packets/second)(1) —
HMI/MSG: 1000
• EtherNet/IP™
• ControlNet™
• DeviceNet™
Communication options • Data Highway Plus —
• Remote I/O
• SynchLink
• Third-party process and device networks
EtherNet/IP nodes supported, max(2) 100 nodes 175 nodes 250 nodes 250 nodes —
• GuardLogix 5580 Controllers front EtherNet/IP port. See ‘EtherNet/IP nodes supported,
max’ in this table.
• 256 EtherNet/IP; 128 TCP (1756-EN2x)
Network connections, per network module located • 128 EtherNet/IP; 64 TCP (1756-ENBT) —
in the local chassis • 100 ControlNet (1756-CN2/A)
• 40 ControlNet (1756-CNB/D, 1756-CNB/E)
• 128 ControlNet (1756-CN2/B)
Controller redundancy — —
Integrated motion • Integrated Motion on the EtherNet/IP network —
• For the safety task, GuardLogix controllers support Ladder Diagram only.
• For standard tasks, GuardLogix controllers support:
– Ladder Diagram (LD)
Programming languages —
– Structured Text (ST)
– Function Block Diagram (FBD)
– Sequential Function Chart (SFC)
(1) I/O numbers are maximums; they assume no HMI/MSG. HMI/MSG numbers are maximums, they assume no I/O. Packet rates vary depending on packet size. For more details, see Troubleshoot EtherNet/IP Application Technique,
publication ENET-AT003, and the EDS file for a specific catalog number.
(2) A node is an EtherNet/IP device that you add directly to the I/O configuration, and counts toward the node limits of the controller. For more information on EtherNet/IP nodes, see the ControlLogix 5580 Controllers and GuardLogix
5580 Controllers User Manual, publication1756-UM543.
(3) The USB port is intended for temporary local programming purposes only and not intended for permanent connection. Do not use the USB port in hazardous locations.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 19

1756 ControlLogix and GuardLogix Controllers

Technical Specifications - GuardLogix 5580 Controllers

1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES, 1756-L8SP,
Attribute
1756-L81ESK 1756-L82ESK 1756-L83ESK 1756-L84ESK 1756-L8SPK
User memory 3 MB 5 MB 10 MB 20 MB —
(2)
Safety memory 1.5 MB 2.5 MB 5 MB 6 MB
Digital I/O, max 128,000 —
Analog I/O, max 4000 —
Total I/O, max 128,000 —
Optional nonvolatile memory storage 2 GB Secure Digital Card (1784-SD2), ships pre-installed in the controller —
Embedded in safety
Energy storage module Embedded in controller, nonremovable partner, nonremovable
Current draw @ 1.2V DC 5.0 mA
Current draw @ 5.1V DC 1.20 A
Power dissipation 6.2 W
Thermal dissipation 21.2 BTU/hr
50V (continuous), Basic Insulation type, Ethernet to backplane, USB to backplane, and USB to Ethernet
Isolation voltage Type tested at 1000V AC for 60 seconds
Weight, approx 0.394 kg (.868 lb)
Slot width 1
Module location Chassis-based, any slot (the safety partner must be installed in the slot to the immediate right of the primary controller)
Chassis 1756-A4, 1756-A4K, 1756-A7, 1756-A7K, 1756-A10, 1756-A10K, 1756-A13, 1756-A13K,1756-A17, 1756-A17 K Series B, Series C
1756-PA50, 1756-PA72, 1756-PA72K, 1756-PA75, 1756-PA75K, 1756-PB50, 1756-PB72, 1756-PB72K, 1756-PB75, 1756-PB75K,
Power supply, standard 1756-PH75, 1756-PC75
Power supply, redundant 1756-PA75R, 1756-PA75RK, 1756-PB75R, 1756-PB75RK, 1756-PSCA2, 1756-PSCA2K
3 - on USB port
Wire category(1)
2 - on Ethernet ports
Ethernet connections:
Wire size
Ethernet cabling and installation according to IEC 61918 and IEC 61784-5-2
North American temperature code T4
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) Use this conductor category information to plan conductor routing. See Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.
(2) Same as corresponding primary controller.

20 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Environmental Specifications -GuardLogix 5580 Controllers

1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES
Attribute
1756-L81ESK, 1756-L82ESK, 1756-L83ESK, 1756-L84ESK, 1756-L8SP, 1756-L8SPK
Temperature, operating (SIL 2/PLd) 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F) for Series C Chassis
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), Note: If operating above +55 °C (+131 °F), modules greater than 6.2W shall not be installed in slots
IEC 60068-2-14 (Test Nb, Operating Thermal Shock) adjacent to the controller.

Temperature, operating (SIL 3/PLe)

IEC 60068-2-1 (Test Ad, Operating Cold), 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F) for Series C Chassis
IEC 60068-2-2 (Test Bd, Operating Dry Heat), 0 °C < Ta < +50 °C (+32 °F < Ta < +122 °F) for Series B Chassis
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), Chassis series B and C: -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
60 °C (140 °F) for Series C Chassis
Temperature, Surrounding Air, max (SIL 2/PLd) Note: If operating above +55 °C (+131 °F), modules greater than 6.2W shall not be installed in slots
adjacent to the controller.
60 °C (140 °F) for Series C Chassis
Temperature, Surrounding Air, max (SIL 3/PLe)
50 °C (122 °F) for Series B Chassis
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
IEC 61000-4-3 3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
3V/m with 1 kHz sine-wave 80% AM from 2700…6000 MHz
EFT/B Immunity ±2 kV at 5 kHz on Ethernet ports
IEC 61000-4-4
Surge Transient Immunity
±2 kV line-earth (CM) on Ethernet ports
IEC 61000-4-5
Conducted RF Immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
IEC 61000-4-6

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 21

1756 ControlLogix and GuardLogix Controllers

Certifications - GuardLogix 5580 Controllers

1756-L81ES, 1756-L82ES, 1756-L83ES, 1756-L84ES, 1756-L81ESK, 1756-L82ESK, 1756-L83ESK, 1756-L84ESK,
Certification(1)
1756-L8SP, 1756-L8SPK
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
CSA Certified Process Control Equipment. See CSA File 150115.
CSA
CSA Certified Process Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations. See CSA File 150115.
FM FM Approved Equipment for use in Class I Division 2 Group A,B,C,D Hazardous Locations
European Union 2014/30/EU EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
European Union 2006/42/EC MD, compliant with:
• EN ISO 13849-1; Safety-related parts of control systems
CE • EN 62061; Functional safety of safety-related control systems
• Up to Cat. 4/PL e according to EN ISO 13849-1 and SIL CL 3 according to EN/IEC 62061 when used in combination with the 1756-L8SP
safety partner
• Up to Cat. 3/PL d according to EN ISO 13849-1, and SIL CL 2 according to EN/IEC 62061 when not used in combination with the 1756-L8SP
safety partner
• TÜV 01/205/5611
European Union 2011/65/EU RoHS, compliant with:
• EN 50581; Technical documentation
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 2014/34/EU ATEX Directive, compliant with:
• EN 60079-0; General Requirements
Ex • EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• II 3 G Ex nA IIC T4 Gc
• DEMKO13ATEX1325026X
IECEx System, compliant with:
• IEC 60079-0; General Requirements
IECEx • IEC 60079-15; Potentially Explosive Atmospheres, Protection “n”
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 14.0008X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
TÜV certified for functional safety(2) Capable of SIL 3, CAT. 4/PLe
EtherNet/IP ODVA conformance tested to CIP Safety EtherNet/IP specifications
(1) See the Product Certification link at http://www.rockwellautomation.com/global/certification/overview.page for Declarations of Conformity, Certificates, and other certification details.
(2) When used with specified firmware revisions. See the Product Safety Certificate at http://www.rockwellautomation.com/global/certification/overview.page for a full list of safety-related certifications.

22 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

1756-L7S GuardLogix Controllers Specifications

Technical Specifications - 1756-L7S GuardLogix Controllers
Attribute 1756-L71S, 1756-L71SK 1756-L72S, 1756-L72SK 1756-L73S, 1756-L73SK 1756-L7SP, 1756-L7SPK
User memory 2 MB 4 MB 8 MB —
(2)
Safety memory 1 MB 2 MB 4 MB
I/O memory 0.98 MB —

Optional nonvolatile memory storage 12 GB

GB (1756-SD1 ships with every controller) —
(1756-SD2)
Digital I/O, max 128,000 —
Analog I/O, max 4000 —
Total I/O, max 128,000 —
Replacement battery —
• 1756-SPESMNSE capacitor energy storage
• 1756-ESMCAP capacitor energy storage module (removable, ships installed with module for the safety partner (removable,
every controller) no residual WallClockTime power backup)
• 1756-ESMNSE capacitor energy storage module (removable, no residual • 1756-SPESMNRM capacitor energy storage
Energy storage modules WallClockTime power backup) module for the safety partner
• 1756-ESMNRM capacitor energy storage module (nonremovable, helps prevent USB (nonremovable, helps prevent USB
connection and SD card use to help secure the controller) connection and SD card use to help secure
the controller)
Current draw @ 1.2V DC 5 mA
Current draw @ 5.1V DC 800 mA
Power dissipation 2.5 W
Thermal dissipation 8.5 BTU/hr
Isolation voltage 30V (continuous), basic insulation, USB port-to-system, type tested at 980V AC for 60 s
Weight, approx 0.25 kg (0.55 lb)
Slot width 2 (both modules needed; each is one slot)
Module location Chassis-based, any slot (the safety partner must be installed in the slot to the immediate right of the primary controller)
Chassis 1756-A4, 1756-A4K, 1756-A7, 1756-A7K, 1756-A10, 1756-A10K, 1756-A13, 1756-A13K,1756-A17, 1756-A17K
Power supply, standard 1756-PA50, 1756-PA72, 1756-PA72K, 1756-PA75, 1756-PA75K, 1756-PB50, 1756-PB72, 1756-PB72K, 1756-PB75, 1756-PB75K
Wire category(1) 3 - on USB ports
North American temperature code T4A
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) Use this Conductor Category information to plan conductor routing. See Industrial Wiring and Grounding Guidelines, publication 1770-4.1.
(2) Same as corresponding primary controller.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 23

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-L7S GuardLogix Controllers

1756-L71S, 1756-L72S, 1756-L73S, 1756-L7SP 1756-L71SK, 1756-L72SK, 1756-L73SK,
Attribute
1756-L7SPK
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Temperature, surrounding air, max 60 °C (140 °F)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock) (45 g with SD card installed)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
Conducted RF Immunity Not applicable: USB is a temporary programming port.
IEC 61000-4-6

24 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Certifications - 1756-L7S GuardLogix Controllers

Certification(1) 1756-L71S, 1756-L72S, 1756-L73S, 1756-L7SP 1756-L71SK, 1756-L72SK, 1756-L73SK, 1756-L7SPK
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
CE • EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
European Union 2006/42/EC MD, compliant with:
• EN 60204-1; Electrical equipment of machines
• EN ISO 13849-1; Safety-related parts of control systems
• EN 62061; Functional safety of safety-related control systems
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-0; General Requirements
Ex • EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• Ex nA IIC T4 Gc
• DEMKO15 ATEX 1593X
IECEx System, compliant with:
• EN 60079-0; General Requirements
IECEx • EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 15.0125X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Capable of SIL CL 3 according to IEC 61508, capable of Category 4 according to EN954-1, and capable of PL(e) according to ISO 13849-1
TÜV certified for functional safety(2) when used as described in the GuardLogix 5570 and Compact GuardLogix 5370 Controller Systems Safety Reference Manual, publication
1756-RM099.
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.
(2) When used with specified firmware revisions. See the Product Safety Certificate at the Product Certification link ( http://www.ab.com) for a full list of safety-related certifications.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 25

1756 ControlLogix and GuardLogix Controllers

1756-L6S GuardLogix Controllers Specifications

Technical Specifications - 1756-L6S GuardLogix Controllers
Attribute 1756-L61S 1756-L62S 1756-L63S 1756-LSP
User memory 2 MB 4 MB 8 MB —
Same as corresponding primary
Safety memory 1 MB 1 MB 3.75 MB
controller
I/O memory 478 KB —
(2)
128 MB (1784-CF128)
Optional nonvolatile memory storage 1 GB (1784-SD1, ships with every controller) —
2 GB (1784-SD2)
Digital I/O, max 128,000 —

Analog I/O, max 4000 —

Total I/O, max 128,000 —

Replacement battery 1756-BA2 (0.50 g lithium)

Energy storage modules —
Current draw @ 1.2V DC —
Current draw @ 5.1V DC 1200 mA
Current draw @ 24V DC 14 mA
Power dissipation 3.5 W
Thermal dissipation 11.9 BTU/hr
30V (continuous), Basic Insulation Type, RS-232 to system
Isolation voltage Type tested at 720V DC for 60 s
Serial cables 1756-CP3 or 1747-CP3, right angle connector to controller, straight to serial port, 3 m (9.84 ft)
0.32 kg
Weight, approx (0.70 lb)
Slot width 2 (both modules needed; each is one slot)
Module location Chassis-based, any slot (the safety partner must be installed in the slot to the immediate right of the primary controller)
Chassis 1756-A4, 1756-A7, 1756-A10, 1756-A13, 1756-A17
Power supply standard 1756-PA50, 1756-PA72, 1756-PA75, 1756-PB50, 1756-PB72, 1756-PB75
Wire category(1) 2 - on RS-232 port
North American temperature code T4A
Enclosure type rating None (open-style)
(1) Use this conductor category information for to plan conductor routing as described in the system level installation manual. See the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.
(2) RSLogix 5000® programming software, version 18 or later.

26 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-L6S GuardLogix Controllers

Attribute 1756-L61S, 1756-L62S, 1756-L63S, 1756-LSP
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0 °C…+60 °C (+32…+140 °F) on 1756-L61S, 1756-L62S, 1756-L63S, 1756-LSP
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 60 °C (140 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions
CISPR 11 Class A
IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
EFT/B immunity ±4 kV at 5 kHz on RS-232 port
IEC 61000-4-4
Surge transient immunity ±2 kV line-earth (CM) on RS-232 port
IEC 61000-4-5
Conducted RF immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
IEC 61000-4-6

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 27

1756 ControlLogix and GuardLogix Controllers

Certifications - 1756-L6S GuardLogix Controllers

Certification(1) 1756-L61S, 1756-L62S, 1756-L63S, 1756-LSP
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
CSA Certified Process Control Equipment. See CSA File LR54689C.
CSA CSA Certified Process Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations. See CSA File LR69960C.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61000-6-4; Industrial Emissions
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
CE • EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
European Union 2006/42/EC MD, compliant with:
• EN 60204-1; Electrical equipment of machines
• EN ISO 13849-1; Safety-related parts of control systems
• EN 62061; Functional safety of safety-related control systems
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
FM FM Approved Equipment for use in Class I, Division 2 Group A, B, C, D Hazardous Locations
KC Korean Registration of Broadcasting and Communication Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3

TÜV certified for functional safety(2) Capable of Cat. 4/PL e according to EN ISO 13849-1 and SIL 3 according to EN 62061/IEC 61508 when used as described in the
GuardLogix Controller Systems Safety Reference Manual, publication 1756-RM093.
UL certified for functional safety(2) Capable of SIL CL 3, see UL File E256621.
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.
(2) When used with specified firmware revisions.

28 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

1756 GuardLogix-XT Controllers

The GuardLogix-XT™ controllers function the same way as the traditional GuardLogix controllers. The GuardLogix-XT
controllers are conformally coated for extended protection in harsh, corrosive environments. The GuardLogix-XT
system can withstand temperature ranges from -25…+70 °C (-13…+158 °F). You must use a 1756-L73SXT primary
controller with a 1756-L7SPXT safety partner.

Customers who previously used the LXT chassis should now migrate to the K version of the chassis.

Attribute 1756-L73SXT 1756-L7SPXT

User memory 8 MB —
Safety memory 4 MB Same as corresponding primary controller
I/O memory 0.98 MB
Digital I/O, max 128,000
Analog I/O, max 4,000
Total I/O, max 128,000
• 1756-ESMCAPXT capacitor energy storage module extreme • 1756-SPESMNSEXT capacitor energy storage module for the
temperature (removable, ships installed with every controller) safety partner extreme temperature (removable, no residual
• 1756-ESMNSEXT capacitor energy storage module extreme WallClockTime power backup)
Energy storage modules temperature (removable, no residual WallClockTime power backup) • 1756-SPESMNRMXT capacitor energy storage module for the
• 1756-ESMNRMXT capacitor energy storage module extreme safety partner extreme temperature (nonremovable, helps
temperature (nonremovable, helps prevent USB connection and SD prevent USB connection and SD card use to help secure the
card use to help secure the controller) controller)
Current draw @ 1.2V DC 5 mA
Current draw @ 5.1V DC 800 mA
Power dissipation 2.5 W
Thermal dissipation 8.5 BTU/hr
30V (continuous), Basic Insulation, USB port to backplane
Isolation voltage
Type tested at 980V AC for 60 s
Weight, approx 0.25 kg (0.55 lb)
Slot width 2 (need 2 modules; each uses a slot)
Module location Chassis-based, any slot (the safety partner must be in a slot to the right of the primary)
1756-A7XT, 1756-A10XT
Chassis
For low temperature applications only, use 1756-A4K, 1756-A7K, 1756-A10K, 1756-A13K, 1756-A17K
Power supply 1756-PAXT, 1756-PA30XT, 1756-PBXT, 1756-PB30XT
Wire category(1) 3 - on USB ports
North American temperature code T4A
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) Use this conductor category information to plan conductor routing as described in the system level installation manual. See the Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 29

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756 GuardLogix-XT Controllers

Attribute 1756-L73SXT, 1756-L7SPXT
Temperature, operating -25 °C< Ta < +70 °C (-13 °F < Ta < +158 °F)
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), When using a 1756-A7LXT chassis, surrounding air temperature range is -25…+60 °C (-13…+140 °F)
IEC 60068-2-14 (Test Nb, Operating Thermal Shock) even when using an XT controller

Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 70 °C (158 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g (45 g with SD card installed)
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
Conducted RF Immunity Not applicable: USB is a temporary programming port.
IEC 61000-4-6.

30 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Certifications - 1756 GuardLogix-XT Controllers

Certification(1) 1756-L73SXT, 1756-L7SPXT
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
CE • EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
European Union 2006/42/EC MD, compliant with:
• EN 60204-1; Electrical equipment of machines
• EN ISO 13849-1; Safety-related parts of control systems
• EN 62061; Functional safety of safety-related control systems
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-0; General Requirements
Ex • EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• II 3 G Ex nA IIC T4 Gc
• DEMKO15 ATEX 1593X
IECEx System, compliant with:
• EN 60079-0; General Requirements
IECEx • EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 15.0125X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
(2) Capable of SIL CL 3 according to IEC 61508, capable of Category 4 according to EN954-1, and capable of PL(e) according to ISO 13849-1
TÜV certified for functional safety when used as described in the GuardLogix Controller Systems Safety Reference Manual, publication 1756-RM093.
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.
(2) When used with specified firmware revision.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 31

1756 ControlLogix and GuardLogix Controllers

1756 Armor ControlLogix and Armor GuardLogix Controllers

The Armor™ ControlLogix® and Armor™ GuardLogix® controllers extend the ControlLogix platform to the
On-Machine™ space to put industrial control closer to the application, and sometimes onto the machine itself.

The Armor GuardLogix controllers are certified for use in safety applications up to Safety Integrity Level (SIL) 3 and
Performance Level PLe (Category 4), where the de-energized state is the safe state.

Dual independent EtherNet/IP ports and Device Level Ring (DLR) capabilities provide resiliency from loss of network
connections due to one connection failure.

The controllers support the same environmental ratings and global certifications as the ControlLogix and GuardLogix
controllers, but now provide Ingress Protection (IP67 and UL Type 4/4x) for dust and washdown protection.

With so many hardware functions in one device, these controllers minimize cabinet hardware and simplify wiring
layouts. The controllers do not require specialty tools or specialty personnel for component replacement. These features
can help improve Mean Time to Repair (MTTR), simplify troubleshooting, and make system status readily available
without having to open a cabinet or visit a control room.
Features - Armor ControlLogix and Armor GuardLogix Controllers
Feature 1756-L72EROM, 1756-L73EROM 1756-L72EROMS, 1756-L73EROMS
Communication options Standard on EtherNet/IP networks Standard and safety on EtherNet/IP networks
Network connections 256 EtherNet/IP; 128 TCP
Controller redundancy Not supported
• Relay Ladder Logic (RLL)
• Relay Ladder Logic (RLL) • Structured Text
• Structured Text • Function Block Diagram
Programming languages • Function Block Diagram • Sequential Function Chart (SFC)
• Sequential Function Chart (SFC) • Safety Task supports only RLL and the additional safety
application instructions

32 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Armor ControlLogix and Armor GuardLogix Controller Specifications

Technical Specifications - Armor ControlLogix and Armor GuardLogix Controllers

Attribute 1756-L72EROM 1756-L72EROMS 1756-L73EROM 1756-L73EROMS
Standard memory 4 MB 4 MB 8 MB 8 MB
Safety memory — 2 MB — 4 MB
I/O memory 0.98 MB
1 GB (1756-SD1 ships with every controller)
Optional nonvolatile memory storage
2 GB (1756-SD2)
Digital I/O, max 128,000
Analog I/O, max 4000
Total I/O, max 128,000
Input voltage range 18…32V DC
Input voltage, nom 24V DC
Input system power, pins 2 and 3 18…32V DC @ 8 A
Input pass through power, pins 1 and 4 SELV 18…32V DC @ 8 A
Output external power, pins 2 and 3 18…32V DC @ 6 A
Output pass through power, pins 1 and 4 SELV 18…32V DC @ 8 A
Fusing Non-replaceable fuse is soldered in place(3)
30V (continuous), Basic Insulation Type, Power to enclosure, Ethernet channels to Power, and non-redundant
Ethernet channels to non-redundant Ethernet channels.
Isolation voltage No isolation between redundant Ethernet channels
Type tested at 707V DC for 60 seconds
Weight, approx 7.04 kg (15.50 lb) 7.15 kg (15.725 lb) 7.04 kg (15.50 lb) 7.15 kg (15.725 lb)
Dimensions 240.0 x 292.0 x 164.52 mm (9.4 x 11.5 x 6.5 in.)
Ethernet ports 4 Ethernet M12 Category 5E
Ethernet cable 802.3 compliant shielded or unshielded twisted pair
USB port(1) USB 1.1, full speed (12 Mbps)
Wire Size PE Ground: 1.3…5.2 mm2 (16…0 AWG)
Terminal block torque specifications PE Ground: 2 N•m (17.7 lb•in)
3 - on USB ports
Wire category(2) 2 - on power ports
2 - on Ethernet ports
UL Type 4/4x
Enclosure type rating Meets IP67 (when marked) with receptacle dust caps or cable termination
(1) The USB port is intended for temporary local programming purposes only and not intended for permanent connection.
(2) Use this Conductor Category information to plan conductor routing. See Industrial Wiring and Grounding Guidelines, publication 1770-4.1.
(3) This fuse is intended to guard against fire hazard due to short circuit conditions.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 33

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - Armor ControlLogix and Armor GuardLogix Controllers

Attribute 1756-L72EROM, 1756-L72EROMS, 1756-L73EROM, 1756-L73EROMS
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0…60 °C (32…140 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Temperature, ambient, max 60 °C (140 °F)
Vibration
2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating
30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
IEC 61000-4-3
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
3V/m with 1 kHz sine-wave 80% AM from 2700…6000 MHz
EFT/B immunity ±3 kV at 5 kHz and 100 kHz on Power Ports
IEC 61000-4-4 ±3 kV at 5 kHz and 100 kHz on Ethernet Ports
Surge transient immunity ±1 kV line-line (DM) and ±2 kV line-earth (CM) on power ports
IEC 61000-4-5 ±2 kV line-earth (CM) on Ethernet ports
Conducted RF immunity 10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
IEC 61000-4-6
Voltage variation
10 ms interruption on DC supply ports
IEC 61000-4-29

34 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Certifications - Armor ControlLogix and Armor GuardLogix Controllers

Certification(1) 1756-L72EROM, 1756-L73EROM 1756-L72EROMS, 1756-L73EROMS
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
European Union 2004/108/EC EMC Directive, compliant with: • EN 61000-6-2; Industrial Immunity
• EN 61326-1; Meas./Control/Lab., Industrial Requirements • EN 61000-6-4; Industrial Emissions
CE • EN 61000-6-2; Industrial Immunity • EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
• EN 61000-6-4; Industrial Emissions European Union 2006/42/EC MD, compliant with:
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B) • EN 60204-1; Electrical equipment of machines
• EN ISO 13849-1; Safety-related parts of control systems
• EN 62061; Functional safety of safety-related control systems
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Capable of Cat. 4/PL e according to EN ISO 13849-1 and SIL 3 according
(2) to EN 62061/IEC 61508 when used as described in the GuardLogix 5570
TÜV certified for functional safety — and Compact GuardLogix 5370 Controller Systems Safety Reference
Manual, publication 1756-RM099.
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.
(2) When used with specified firmware revisions.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 35

1756 ControlLogix and GuardLogix Controllers

Controller Compatibility
The following tables provide compatibility with I/O modules, display devices, and other controllers and communication
devices.

Control Distributed I/O Modules

The controller can control these distributed I/O modules via the I/O Configuration tree in the programming software.

I/O Modules EtherNet/IP ControlNet DeviceNet Remote I/O

Chassis-based I/O
1715 Redundant I/O Yes No No Yes
1746 SLC™ I/O No No No Yes
1756 ControlLogix I/O Yes Yes No No
1769 Compact I/O™ No No Yes Yes(2)
1771 Universal I/O No Yes No Yes
In-cabinet I/O
1734 POINT I/O™ Yes Yes Yes No
1734D POINTBlock I/O No No Yes No
1790, 1790D, 1790P CompactBlock™ LDX I/O No No Yes No
1791D, 1791P, 1791R CompactBlock I/O No No Yes No
1794 FLEX™ I/O Yes Yes Yes Yes
1797 FLEX Ex™ I/O No Yes No No
5069 Compact I/O™ (1) Yes No No No
On-Machine™ I/O
1732 ArmorBlock® I/O Yes No Yes No
1738 ArmorPOINT® I/O Yes Yes Yes No
1792D ArmorBlock® MaXum™ I/O No No Yes No
1799 Embedded I/O No No Yes No
(1) Compatible with ControlLogix 5580 Controllers only.
(2) With a third-party module.

Control Safety Distributed I/O Modules

The GuardLogix controller can control these safety distributed I/O modules in a safety system.

I/O Modules EtherNet/IP ControlNet DeviceNet

In-cabinet I/O
1791DS CompactBlock™ Guard I/O™ No No Yes
1791ES CompactBlock Guard I/O Yes No No
1734 POINT Guard I/O™ Yes No Yes
On-Machine I/O
1732DS ArmorBlock® Guard I/O™ No No Yes
1732ES ArmorBlock Guard I/O Yes No No

36 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Communicate with Display Devices

The controller can communicate with these display devices.

Display Devices EtherNet/IP ControlNet DeviceNet DH+™ Remote I/O RS-232 (DF1)
Industrial Computers
Allen-Bradley® industrial computers (all)(1) Yes Yes Yes Yes Yes Yes
Graphic Terminals
PanelView™ Plus and PanelView e terminals Yes Yes Yes Yes Yes Yes
PanelView Standard terminals Yes Yes Yes Yes Yes Yes
PanelView e terminals No Yes No Yes Yes No
Message Displays
InView™ message displays Yes Yes Yes Yes Yes Yes
(1) Includes Allen-Bradley integrated display rotating media (HDD) and solid state (SSD) computers, Rockwell Automation® non-display computers, and Allen-Bradley integrated display computers with keypad.

Communicate with Other Controllers

The controller can communicate with these programmable controllers.

Controller EtherNet/IP ControlNet DeviceNet DH+ RS-232 (DF1) DH-485(5)
1756 ControlLogix Yes Yes Yes Yes Yes Yes
1756 GuardLogix
5069 CompactLogix™ Yes No No No No No
1768, 1769 CompactLogix Yes Yes Yes No Yes Yes
1768, 1769 Compact GuardLogix
1789 SoftLogix™5800 Yes Yes Yes No Yes No
1794 FlexLogix™ Yes Yes Yes No Yes Yes
PowerFlex® with DriveLogix™ Yes Yes Yes No Yes Yes
1785 PLC-5®(1) (2)(3) Yes Yes Yes Yes Yes No
1747 SLC™(4) Yes Yes Yes Yes Yes Yes
1761 MicroLogix™(4) Yes No Yes No Yes Yes
(4)
1762 MicroLogix Yes No Yes No Yes Yes
(4)
1763 MicroLogix Yes No Yes No Yes Yes
1764 MicroLogix (4) Yes No Yes No Yes Yes
1772 PLC-2® No No No Yes Yes No
1775 PLC-3® No No No Yes Yes No
5250 PLC-5/250 No No No Yes Yes No
(1) The Ethernet PLC-5 controller must be series C, firmware revision N.1 or later; series D, firmware revision E.1 or later; or series E, firmware revision D.1 or later.
(2) The 1785-ENET Ethernet communication interface module must be series A, firmware revision D or later.
(3) The PLC-5, SLC, and MicroLogix processors appear as I/O points to the Logix controller. Use the appropriate DeviceNet interface for the controller.
(4) Use a 1747-L55x controller with OS501 or later.
(5) The 1756-DH485 module supports full DH-485 functionality.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 37

1756 ControlLogix and GuardLogix Controllers

Communicate with Other Communication Devices

The controller can communicate with these communication devices.

Communication Device EtherNet/IP ControlNet DeviceNet DH+
1788-EN2DNR
1788-CN2DN 1788-EN2DNROM
Linking device 1788-EN2DNROM —
1788-CN2FF (On-Machine version)
1788-CN2DN
PCMCIA card — 1784-PCC 1784-PCD 1784-PCMK
1784-PCID
1784-PCIC
PCI card — 1784-PCIDS —
1784-PCICS 1784-CPCIDS
1203-FM1
Drives SCANport™ module (1) — — —
1203-FB1
1203-CN
1770-KFC15 1770-KFD
Communication module (2) — 1770-KF2
1770-KFCD15 1770-KFG
1747-KFC15
1784-PKTCS 1784-PKTX
Communication card — 1784-KTCS —
1784-PKTXD
1784-KTCX15
USB communication device — 1784-U2CN 1784-U2DN 1784-U2DHP
(1) Use a CIP generic MSG instruction to communicate with the 1203-FM1 SCANport™ module on a DIN rail that is remote to the controller. The remote DIN rail also requires a 1794-ACN15 or 1794-ACNR15 ControlNet adapter.
(2) Use the generic module configuration to configure the 1203-CN1 module and a CIP generic MSG instruction to communicate with the module.

38 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

ControlLogix Redundancy
The ControlLogix 5560 and ControlLogix 5570 controllers support controller redundancy. In a redundant controller
system, you need these components:
• Two 1756 chassis, each with the same of the following:
– Number of slots
– Compatible modules in the same slots
– Redundancy firmware revisions in each module
– Two additional ControlNet nodes outside the redundant chassis pair if the application uses ControlNet networks
• One 1756-RM2 or 1756-RM2XT redundancy module per chassis that is connected by a 1756-RMCx cable
• One or two ControlLogix 5560 or ControlLogix 5570 controllers
• As many as seven enhanced communication modules, that is, 1756-CN2/B, 1756-CN2R/B, 1756-CN2RXT
modules, or 1756-EN2T, 1756-EN2TR, 1756-EN2TXT modules

1756-RM2, 1756-RM2XT Redundancy Modules

Technical Specifications - 1756-RM2, 1756-RM2XT Redundancy Modules

Attribute 1756-RM2, 1756-RM2K 1756-RM2XT
Current draw @ 5.1V DC 1.16 A
Current draw @ 24V DC 3.4 mA
Power dissipation 6 W, max
Thermal dissipation 21 BTU/hr
1756-RMC1, 1 m (3.28 ft)
Connector cables 1756-RMC3, 3 m (9.84 ft)
1756-RMC10, 10 m (32.81 ft)
Slot width 1 slot
Module location Chassis-based, any slot
1756-A7XT, 1756-A10XT,
Chassis 1756-A4, 1756-A7, 1756-A10, 1756-A13, 1756-A17 1756-A4LXT, 1756-A5LXT, 1756-A7LXT
Controller families, supported ControlLogix 5560, ControlLogix 5570
Power supply, standard 1756-PA72, 1756-PA75, 1756-PB72, 1756-PB75 1756-PAXT, 1756-PBXT
Power supply, redundant 1756-PA75R, 1756-PB75R, 1756-PSCA2 None
North American temperature code T4
IECEx temperature code T4
ATEX temperature code T4
Enclosure type None (open-style)
Weight, approx 0.29 kg (0.64 lb)
Mounting ControlLogix-XT chassis, single-slot module

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 39

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-RM2, 1756-RM2XT Redundancy Modules

Attribute 1756-RM2, 1756-RM2K 1756-RM2XT
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0…60 °C (32…140 °F) -25…+70 °C (-13…+158 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 60 °C (140 °F) 70 °C (158 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

40 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Certifications - 1756-RM2, 1756-RM2XT Redundancy Modules

Certification(1) 1756-RM2, 1756-RM2K 1756-RM2XT
CSA Certified Process Control Equipment. See CSA File LR54689C.
CSA —
CSA Certified Process Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations. See CSA File LR69960C.
European Union 2004/108/IEC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
UL Listed Industrial Control Equipment, certified for U.S. and Canada. See UL file E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO13ATEX1325026X
IECEx System, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
IECEx • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 14.0008X
FM FM Approved Equipment for use in Class I Division 2 Group A,B,C,D Hazardous Locations —
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 41

1756 ControlLogix and GuardLogix Controllers

ControlLogix Controller Accessories

You can use these accessories with ControlLogix controllers.

Accessory Page
Memory Cards 42
1756 Energy Storage Modules 44
1756 ControlLogix Batteries 50
Serial Communication Cables 51

Memory Cards

Memory cards offer nonvolatile memory to store a user program and tag data on a controller.
• The ControlLogix 5560 controllers support optional 1784-CF128 CompactFlash cards purchased separately.
• The ControlLogix 5570 controllers come with the 1784-SD1 Secure Digital (SD) card installed.
• The ControlLogix 5580 controllers come with the 1784-SD2 Secure Digital (SD) card installed.

The memory cards are installed in a socket on the controller. Through the programming software, you can manually
trigger the controller to save to, or load from, nonvolatile memory or configure the controller to load from nonvolatile
memory on powerup.
Technical Specifications - 1784 Memory Cards
Attribute 1784-CF128 1784-SD1 1784-SD2
Memory 128 MB 1 GB 2 GB
1756-L71, 1756-L71K, 1756-L71S, 1756-L71SK, 1756-L72, 1756-L72K, 1756-L72S, 1756-L72SK,
1756-L72EROM, 1756-L72EROMS, 1756-L73, 1756-L73K, 1756-L73S, 1756-L73SK, 1756-L73EROM,
1756-L73EROMS, 1756-L73XT, 1756-L73SXT, 1756-L74, 1756-L74K, 1756-L75, 1756-L75K
Supported controllers 1756-L6, 1756-L6S(1)
1756-L81E, 1756-L81EK, 1756-L81ES, 1756-L81ESK,1756-L82E, 1756-L82EK, 1756-L82ES, 1756-L82ESK,
1756-L83E, 1756-L83EK, 1756-L83ES, 1756-L83ESK, 1756-L84E, 1756-L84EK, 1756-L84ES, 1756-L84ESK,
1756-L85E, 1756-L85EK
Weight, approx 14.20 g (0.50 oz) 1.76 g (0.06 oz)
(1) For safety controllers using RSLogix 5000 programming software version 18 or later.

Environmental Specifications - 1784 Memory Cards

Attribute 1784-CF128 1784-SD1, 1784-SD2
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), -25…+70 °C (-13…+158 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, storage
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)

42 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1784 Memory Cards

Attribute 1784-CF128 1784-SD1, 1784-SD2
Emissions
Group 1, Class A
CISPR 11
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

Certifications - 1784 Memory Cards

Certification(1) 1784-CF128, 1784-SD1 1784-SD2
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61000-6-4; Industrial Emissions
CE • EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-2; Industrial Immunity
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
(1) See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 43

1756 ControlLogix and GuardLogix Controllers

1756 Energy Storage Modules

These energy storage modules are available for ControlLogix 1756 controllers.

Energy Storage Modules Page

1756-L7 and 1756-L7S Energy Storage Modules 44
Extreme Temperature Energy Storage Modules 46
GuardLogix Safety Partner Energy Storage Modules 47
GuardLogix Extreme-temperature Safety Partner Energy-storage Modules 49

1756-L7 and 1756-L7S Energy Storage Modules

Instead of a battery, the 1756-L7 and 1756-L7S controllers are shipped with a 1756-ESMCAP energy storage module
(ESM) already installed.

Technical Specifications - 1756-L7 and 1756-L7S Energy Storage Modules(1)

Attribute 1756-ESMCAP, 1756-ESMCAPK 1756-ESMNSE, 1756-ESMNSEK 1756-ESMNRM, 1756-ESMNRMK
Capacitor energy storage module (removable,
no residual WallClockTime power backup). Capacitor energy storage module
Use this ESM if your application requires that (nonremovable, helps prevent USB
the installed ESM deplete its residual energy connection and SD card use to help secure
to 40 μJ or less before transporting it into or the controller).
Capacitor energy storage module (removable,
Description out of your application. Additionally, you can If the SD card is installed prior to insertion
ships installed with every controller).
use this ESM with a 1756-L73 (8 MB) or of the 1756-ESMNRM module, the SD card
smaller memory-sized controller only. remains functional, but not removable.
Wait at least 20 minutes for the residual This ESM provides your application an
stored energy to decrease to 40 μJ or less enhanced degree of security.
before you remove the ESM.
Current draw @ 5.1V DC 330 mA 300 mA 330 mA
North American temperature code T4A
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) The energy storage modules for the On-Machine controllers are not field-accessible and must be returned to Rockwell Automaton for maintenance or replacement.

44 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-L7 and 1756-L7S Energy Storage Modules

Attribute 1756-ESMCAP, 1756-ESMCAPK, 1756-ESMNSE, 1756-ESMNSEK, 1756-ESMNRM, 1756-ESMNRMK
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 60 °C (140 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10 …500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

Certifications - 1756-L7 and 1756-L7S Energy Storage Modules

Certification(1) 1756-ESMCAP, 1756-ESMCAPK, 1756-ESMNSE, 1756-ESMNSEK, 1756-ESMNRM, 1756-ESMNRMK
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for US and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
• European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO13 ATEX 1325026X
IECEx System, compliant with:
• EN 60079-0; General Requirements
IECEx • EN 60079-15; Potentially Explosive Atmospheres, Protection ”n”
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 14.0008X
KC Korean Registration of Broadcasting and Communication Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 45

1756 ControlLogix and GuardLogix Controllers

Extreme Temperature Energy Storage Modules

The 1756-L7 XT and the 1756-L7 SXT extreme temperature controllers are shipped with a 1756-ESMCAPXT
installed.
Technical Specifications - 1756 Extreme Temperature Energy Storage Modules
Attribute 1756-ESMCAPXT 1756-ESMNSEXT 1756-ESMNRMXT
Extreme-temperature capacitor energy
storage module (removable, no residual
WallClockTime power backup). Extreme-temperature capacitor energy
Use this ESM if your application requires storage module (nonremovable, helps prevent
that the installed ESM deplete its residual USB connection and SD card use to help secure
Extreme-temperature capacitor energy the controller).
storage module (removable, ships installed energy to 40 μJ or less before
Description transporting it into or out of your If the SD card is installed before insertion of
with every extreme-temperature application. Additionally, you can use this the 1756-ESMNRM module, the SD card
controller). ESM with a 1756-L73 (8 MB) or smaller remains functional, but not removable.
memory-sized controller only. This ESM provides your application an
Wait at least 20 minutes for the residual enhanced degree of security.
stored energy to decrease to 40 μJ or less
before you remove the ESM.
Current draw @ 5.1V DC 330 mA 300 mA 330 mA
North American temperature code T4A
ATEX Temp Code T4
IECEx temperature code T4
Enclosure type rating None (open-style)

Environmental Specifications - 1756 Extreme Temperature Energy Storage Modules

Attribute 1756-ESMCAPXT 1756-ESMNSEXT 1756-ESMNRMXT
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), -25°C < Ta < +70 °C (-13°F < Ta < +158 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 70 °C (158 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10 …500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

46 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Certifications - 1756 Extreme Temperature Energy Storage Modules

Certification(1) 1756-ESMCAPXT, 1756-ESMNSEXT, 1756-ESMNRMXT
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for US and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO13 ATEX 1325026X
IECEx System, compliant with:
• IEC 60079-15; Potentially Explosive Atmospheres, Protection “n”
IECEx • IEC 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 14.0008X
KC Korean Certification of Broadcasting and Communication Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

GuardLogix Safety Partner Energy Storage Modules

The 1756-L7SP safety partner for a GuardLogix system has these energy storage modules available.
Technical Specifications - 1756-L7SP Safety Partner Energy Storage Modules(1)
Attribute 1756-SPESMNSE, 1756-SPESMNSEK 1756-SPESMNRM
Capacitor energy storage module for the safety partner
(removable, no residual WallClockTime power backup). Capacitor energy storage module for the safety partner
Use this ESM if your application requires that the installed ESM deplete (nonremovable, helps prevent USB connection and SD card use to
its residual energy to 40 μJ or less before transporting it into or out of help secure the controller).
Description your application. Additionally, you can use this ESM with a 1756-L73 If the SD card is installed before insertion of the 1756-ESMNRM
(8 MB) or smaller memory-sized controller only. module, the SD card remains functional, but not removable.
Wait at least 20 minutes for the residual stored energy to decrease to This ESM provides your application an enhanced degree of security.
40 μJ or less before you remove the ESM.
Current draw @ 5.1V DC 300 mA 330 mA
North American temperature code T4A
ATEX temperature code T4
IECEx temperature code T4
Enclosure type rating None (open-style)
(1) The energy storage modules for the On-Machine controllers are not field-accessible and must be returned to Rockwell Automaton for maintenance or replacement.

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 47

1756 ControlLogix and GuardLogix Controllers

Environmental Specifications - 1756-L7SP Safety Partner Energy Storage Modules

Attribute 1756-SPESMNSE, 1756-SPESMNSEK 1756-SPESMNRM
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), 0 °C < Ta < +60 °C (+32 °F < Ta < +140 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 60 °C (140 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

Certifications - 1756-L7SP Safety Partner Energy Storage Modules

Certification(1) 1756-SPESMNSE, 1756-SPESMNSEK, 1756-SPESMNRM
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for US and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO15 ATEX 1593X
IECEx System, compliant with:
• IEC 60079-15; Potentially Explosive Atmospheres, Protection “n”
IECEx • IEC 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 15.0125X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

48 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

GuardLogix Extreme-temperature Safety Partner Energy-storage Modules

The 1756-L7SPXT extreme-temperature safety partner is shipped with a 1756-SPESMNSEXT energy storage module
installed.
Technical Specifications - 1756-L7SPXT Extreme-temperature Safety Partner Energy-storage Modules
Attribute 1756-SPESMNSEXT 1756-SPESMNRMXT
Capacitor energy storage module for the extreme-temperature
safety partner (removable, no residual WallClockTime power Capacitor energy storage module for the safety extreme-
backup). temperature partner (helps prevent USB connection and SD card use
Use this ESM if your application requires that the installed ESM to help secure the controller).
Description deplete its residual energy to 40 μJ or less before transporting it into If the SD card is installed before insertion of the 1756-ESMNRM
or out of your application. Additionally, you can use this ESM with a module, the SD card remains functional, but not removable.
1756-L73 (8 MB) or smaller memory-sized controller only.
This ESM provides your application an enhanced degree of security.
Wait at least 20 minutes for the residual stored energy to decrease
to 40 μJ or less before you remove the ESM.
Current draw @ 5.1V DC 300 mA 330 mA
North American temperature code T4A
ATEX Temp Code T4
IECEx temperature code T4
Enclosure type rating None (open-style)

Environmental Specifications - 1756-L7SPXT Extreme-temperature Safety Partner Energy Storage Modules

Attribute 1756-SPESMNSEXT 1756-SPESMNRMXT
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold), -25 °C < Ta < +70 °C (-13 °F < Ta <+158 °F)
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)
Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold), -40…+85 °C (-40…+185 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)
Temperature, surrounding air, max 70 °C (158 °F)
Relative humidity 5…95% noncondensing
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat)
Vibration 2 g @ 10…500 Hz
IEC 60068-2-6 (Test Fc, Operating)
Shock, operating 30 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Shock, nonoperating 50 g
IEC 60068-2-27 (Test Ea, Unpackaged Shock)
Emissions IEC 61000-6-4
ESD immunity 6 kV contact discharges
IEC 61000-4-2 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
Radiated RF immunity 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
IEC 61000-4-3 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 49

1756 ControlLogix and GuardLogix Controllers

Certifications - 1756-L7SPXT Extreme-temperature Safety Partner Energy-storage Modules

Certification(1) 1756-SPESMNSEXT, 1756-SPESMNRMXT
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584.
c-UL-us
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for US and Canada. See UL File E194810.
European Union 2004/108/EC EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
CE • EN 61000-6-2; Industrial Immunity
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with EN 61000-6-4; Industrial Emissions
European Union 94/9/EC ATEX Directive, compliant with:
• EN 60079-15; Potentially Explosive Atmospheres, Protection “n”
Ex • EN 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• DEMKO15 ATEX 1593X
IECEx System, compliant with:
• IEC 60079-15; Potentially Explosive Atmospheres, Protection “n”
IECEx • IEC 60079-0; General Requirements
• II 3 G Ex nA IIC T4 Gc
• IECEx UL 15.0125X
KC Korean Registration of Broadcasting and Communications Equipment, compliant with Article 58-2 of Radio Waves Act, Clause 3
Russian Customs Union TR CU 020/2011 EMC Technical Regulation
EAC
Russian Customs Union TR CU 004/2011 LV Technical Regulation
(1) When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.

1756 ControlLogix Batteries

Each ControlLogix 5560 controller ships with a battery. The ControlLogix 5560 controllers have nonvolatile memory if
you install a 1784-CF128 industrial CompactFlash card. With nonvolatile memory, the controller can be used without a
battery. If you do not use a battery, current tag data remains in the state it was when the nonvolatile memory was saved.

These tables summarize battery life, replacement battery compatibility, and recommendations for use of an
externally-mounted battery assembly.
Technical Specifications - 1756 ControlLogix Batteries (1)
Attribute 1756-BA1 1756-BA2 1756-BATM(3) 1756-BATA
Replacement lithium battery for
Externally mounted battery
Description Lithium battery (0.59 g) Lithium battery (0.59 g) 1756-BATM (5 g max lithium per
assembly each D cell; contains 2 D cells)
1756-L61, 1756-L62, 1756-L63
1756-L61, 1756-L62, 1756-L63 1756-L61, 1756-L62, 1756-L63
ControlLogix controllers controllers, series B 1756-BATM battery module
controllers, series A controllers, series A
1756-L64, 1756-L65 controllers
GuardLogix controllers — 1756-L61S, 1756-L62S, 1756-L63S — —
1756-L55M controllers(2) 1756-L55M controllers(3)
Supported legacy controllers — 1756-BATM battery module
1756-L60M03SE controller 1756-L60M03SE controller
(1) To ship lithium batteries globally, there can be specific restrictions and special packaging requirements. Contact the shipping company for packaging and shipping guidelines and restrictions.
(2) The 1756-L55M22, 1756-L55M23, and 1756-L55M24 controllers have nonvolatile memory and can be used without a battery.
(3) The 1756-BATM externally mounted battery assembly is recommended for use with all 1756-L55x controllers, and is highly recommended for use with all series A 1756-L6x controllers, and provides longer battery life than the
1756-BA1 battery. The 1756-BATM assembly includes one 1756-BATA lithium battery assembly and a 1 m (3.28 ft) cable to connect housing to the controller.

50 Rockwell Automation Publication 1756-TD001O-EN-P - February 2018

 1756 ControlLogix and GuardLogix Controllers

Serial Communication Cables

The 1756-L6 and 1756-L6S controllers have a built-in serial port.

Technical Specifications - 1756 Serial Cables
Attribute 1756-CP3 1747-CP3
Connector type Female 9-pin D-shell
Connector angle Right-angle connector to controller, straight to serial port
Length 3 m (9.84 ft)

Rockwell Automation Publication 1756-TD001O-EN-P - February 2018 51

Rockwell Automation Support
Use the following resources to access support information.

Knowledgebase Articles, How-to Videos, FAQs, Chat,

Technical Support Center www.rockwellautomation.com/knowledgebase
User Forums, and Product Notification Updates.
www.rockwellautomation.com/global/support/get-support-
Local Technical Support Phone Numbers Locate the phone number for your country.
now.page
Find the Direct Dial Code for your product. Use the www.rockwellautomation.com/global/support/direct-
Direct Dial Codes code to route your call directly to a technical support dial.page
engineer.
Installation Instructions, Manuals, Brochures, and
Literature Library www.rockwellautomation.com/literature
Technical Data.

Product Compatibility and Download Center Get help determining how products interact, check
features and capabilities, and find associated www.rockwellautomation.com/global/support/pcdc.page
(PCDC) firmware.

Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the
How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.

Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Allen-Bradley, Armor, ArmorBlock, ArmorBlock MaXum, ArmorPOINT, CompactBlock, Compact I/O, CompactLogix, ControlLogix, ControlLogix-XT, Data Highway Plus, DH+, DriveLogix, FLEX, FLEX Ex, FLEX I/O-XT, FlexLogix,
Guard I/O, GuardLogix, GuardLogix-XT, InView, LISTEN.THINK.SOLVE., MicroLogix, On-Machine, PanelView, PLC-2, PLC-3, PLC-5, POINT I/O, POINT Guard I/O, PowerFlex, Rockwell Automation, Rockwell Software, RSLogix 5000, SCANport,
SLC, SoftLogix, and SynchLink are trademarks of Rockwell Automation, Inc.
ControlNet, DeviceNet, and EtherNet/IP are trademarks of ODVA, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Publication 1756-TD001O-EN-P - February 2018

Supersedes Publication 1756-TD001N-EN-P - May 2017 Copyright © 2018 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.