Scribd
Upload
826 views3 pages

National Guard Epoxy Red Oxide Primer

National Guard Epoxy Red Oxide Primer is a two-component, polyamide cured epoxy resin primer that provides corrosion resistance when used on steel. It adheres well to multiple substrates and dries to a smooth, red finish. The primer can be overcoated with National polyurethane coatings and is recommended for protecting steel in moderately to severely corrosive environments.

Uploaded by

Cyril J Padiyath
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
826 views3 pages

National Guard Epoxy Red Oxide Primer

National Guard Epoxy Red Oxide Primer is a two-component, polyamide cured epoxy resin primer that provides corrosion resistance when used on steel. It adheres well to multiple substrates and dries to a smooth, red finish. The primer can be overcoated with National polyurethane coatings and is recommended for protecting steel in moderately to severely corrosive environments.

Uploaded by

Cyril J Padiyath
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

NATIONAL GUARD EPOXY RED OXIDE PRIMER

PROTECTIVE COATINGS TECHNICAL DATA SHEET

NATIONAL GUARD EPOXY RED OXIDE PRIMER


PRODUCT National Guard Epoxy Red Oxide Primer is a two pack
DESCRIPTION polyamide cured epoxy resin based primer. It has excellent
adhesion to steel, galvanized steel, cementitious and wooden
materials. It has excellent water and chemical resistances. The
fully cured film provides good abrasion and impact
resistances.

RECOMMENDED An anti-corrosive primer for steel in moderately to severely


USES corrosive environments. It can be overcoated with two
component National Polyurethane coating for exterior
applications.

TECHNICAL DATA
COLOUR, DRY FILM Red
FINISH, DRY FILM Smooth / Matt
VOLUME SOLIDS 52 ± 2%
(ASTM D2697)
SPECIFIC GRAVITY 1.60 ± 0.05 (of mix)
THEORETICAL SPREADING 13.0 – 8.6 M2/LTR
RANGE
RECOMMENDED DFT RANGE 40 – 60 Microns/Coat
(DRY FILM THICKNESS)
RECOMMENDED WFT RANGE 75 – 115 Microns/Coat
(WET FILM THICKNESS)
FLASH POINT 25ºC
FLEXIBILITY Good
CHEMICAL RESISTANCE Excellent
ABRASION RESISTANCE Good

DRYING TIME
Drying time @ 30°C (Temperature, humidity, air movement, film thickness and number of coats all
affect the drying time.)
TOUCH DRY 5 – 6 hours
*DRY TO RECOAT / OVERCOAT Minimum 10 hours – Maximum 7 days
FULLY CURED 7 days
*With the same generic type paint.

Rev. 05/10
Page 1/3 www.national-paints.com
NATIONAL GUARD EPOXY RED OXIDE PRIMER
PROTECTIVE COATINGS TECHNICAL DATA SHEET

ADVANTAGES
NATIONAL GUARD EPOXY RED Two pack, easy to mix and use, it provides good abrasion
OXIDE PRIMER resistance, good corrosion resistance, excellent adhesion on
properly cleaned steel, good abrasion and impact resistances.

APPLICATION INSTRUCTION
SURFACE PREPARATION Oil and grease should be removed by solvent cleaning. Sand
blast to Sa 2.5, then clean & dry. Apply immediately National
Guard Epoxy Red Oxide Primer after the steel has been blasted.

REPAIR Corroded areas should be power tool cleaned to St3 or blast


cleaned to Sa2 or better. Existing system should be dry and free
from loose paint, salt, grease and other contaminants prior to
overcoating.

APPLICATION DATA
APPLICATION METHOD Airless Spray Conventional Spray Brush
CLEANING/THINNING National Epoxy Thinner (Thinner should only be added after
mixing the components.)
THINNER (VOLUME) 5 – 10% 10 – 15% 10%
CONV. SPRAY REQUIREMENTS Atomizing Pressure : 40 psi
AIRLESS SPRAY 2200 psi
REQUIREMENTS
NOZZLE SIZE 0.018” – 0.020”
MIXING RATIO (BY VOLUME) Base : Hardener
4: 1 (Mix thoroughly, keep for 10 – 15 minutes)
POT LIFE @ 30ºc (100 ml) 8 hours (reduced at higher temperature)
Note: Material may gel at elevated temperature.

SYSTEM
No. of Coats x DFT (Microns)
RECOMMENDED SYSTEM National Guard Epoxy Red Oxide Primer : 1 x 50
To be applied on prepared surface.
National Guard Undercoat H.B. : 1 x 125
Mandatory National Guard Topcoat : 1 x 50
OR
Recommended National Polyurethane Topcoat : 1 x 40

ADDITIONAL DATA
SHELF LIFE @ 30ºC 18 months, in original sealed container, with proper storage
conditions.

Rev. 05/10
Page 2/3 www.national-paints.com
NATIONAL GUARD EPOXY RED OXIDE PRIMER
PROTECTIVE COATINGS TECHNICAL DATA SHEET

HEALTH & SAFETY


SAFETY As a general rule, avoid skin and eye contact by wearing
PRECAUTIONS overalls, gloves, goggles, and airmask etc. Spillage on skin
should immediately be removed by thorough washing with
water and soap or suitable cleaner. Eye should be flushed with
fresh water. Avoid inhalation of vapours and paint mist by
wearing suitable airmask. In the event of ingestion and eye
contact, seek medical attention immediately. Painting must be
carried out in well-ventilated area.
This as industrial product, contains flammable materials and
should be kept away from the sparks and open flames, smoking
in the area should not be permitted. Local safety regulations
should be followed.

STORAGE & HANDLING


STORAGE Store the paint in proper storage conditions as per the local
regulations. Keep the paint container in sealed condition under
shed, away from direct sunlight and extreme temperatures. Do
not stock paint material near to any ignition sources. Do not put
back the half or unused material back in original container,
containing the supplied paint, to avoid contamination. Handle
with care. Stir well before use.

NOTE: We warranty only the quality of our product and this data sheet is based on results obtained from experience and tests.
We reserve the right to change data without prior notice. For surface preparation, safety details refer specifier and safety
data.

This data sheet supersedes all previous issued.


Issued: 0608

Rev. 05/10
Page 3/3 www.national-paints.com

You might also like