Scribd
Upload
608 views1 page

Screw, ISO 7380, Six Lobe, Metic, Torx

The document provides specifications for metric six-lobe button head cap screws. It includes dimensional information like nominal size, thread pitch, and recess size. It describes the screw's fully threaded design to the head and six-lobed recess. Applications include uses where a wider bearing surface is needed or in thin material that cannot accommodate a countersunk head. The document also outlines material composition options, heat treatment requirements, hardness levels, tensile strength, and common plating for carbon steel and stainless steel versions.

Uploaded by

Derek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
608 views1 page

Screw, ISO 7380, Six Lobe, Metic, Torx

The document provides specifications for metric six-lobe button head cap screws. It includes dimensional information like nominal size, thread pitch, and recess size. It describes the screw's fully threaded design to the head and six-lobed recess. Applications include uses where a wider bearing surface is needed or in thin material that cannot accommodate a countersunk head. The document also outlines material composition options, heat treatment requirements, hardness levels, tensile strength, and common plating for carbon steel and stainless steel versions.

Uploaded by

Derek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

METRIC FASTENERS

ISO 7380
Six-Lobe SOCKETS, SIX-LOBE

S
A
W
T

F
H L

METRIC - Six-Lobe ISO 7380 Button Head Cap Screws ISO 7380

A H T W S F

Unthreaded Fillet
Nominal Thread Head Recess Wall Six-Lobe
Head Height Section Under Transition
Size Pitch Diameter Protrusion Thickness Recess Size
the Head Diameter

Max Min Max Min Min Min Max Min Max


M3 0.5 5.7 5.4 1.65 1.40 1.04 0.2 1.0 0.5 3.6 T10
M4 0.7 7.60 7.24 2.20 1.95 1.3 0.3 1.4 0.7 4.7 T20
M5 0.8 9.50 9.14 2.75 2.50 1.56 0.38 1.6 0.8 5.7 T25
M6 1 10.50 10.07 3.3 3.0 2.08 0.74 2 1 6.8 T30

Tolerance on Length 6mm: ±.24 8-10mm: ±.29 12-16mm: ± .35 20-30mm: ±.42 35-50mm: ±.5

Has a similar thread design as a metric socket cap screw but is fully threaded to the head. The dome shaped head is wider and
Description has a lower profile than a socket cap screw and has a six-lobed recess.
Used when a wider bearing surface or a smoother, more finished appearance is desired, or in material too thin to accomodate a
Applications/
countersunk head. Button head screws do not afford the strength of socket head cap screws due to their head geometry and are
Advantages designed for light fastening applications.
Class 10.9 Steel Stainless
May be made from a steel, which conforms to any of the following
chemical composition requirements--
Carbon Steel: Carbon: 0.25-0.55%; Phosphorous: 0.035%
maximum; Sulfur: 0.035% maximum.
Material Carbon Steel with additives such as Boron, Manganese or Chromium:
Carbon: 0.20-0.55%; Phosphorous: 0.035% max; Sulfur: 0.035% A2 Class 50 Stainless Steel
max.
Alloy steel which contains one or more of the following: Chromium,
Nickel, Molybdenum or Vanadium: Carbon: 0.20-0.55%;
Phosphorous: 0.035% max; Sulfur: 0.035% max.
Class 10.9 button head screws shall be heat treated by
Heat Treatment quenching in oil from above the transformation temperature and -
reheating to a tempering temperature of 425°C minimum.

Hardness Rockwell C 32 - 39 (Vickers HV 320 - 380) -

Tensile Strength 1,040 N/mm minimum


2
600 N/mm2

Proof Load 940 N/mm2 minimum 450 N/mm2

Plating Screws are usually provided with a zinc finish. Stainless screws are provided with a plain finish.

This page prints with a watermark.


549

You might also like