UNI-JOINT PLUGS／HYDRO-CIRCUIT BLOCKS SPOT COOLING PIPES

－HEAT PROOF TYPE－

V Non JIS material definition is listed on P.1351 - 1352
■ Uni-joint plugs ■ SPOT COOLING PIPES
JWRH 17.5 SWCP (Fixed Type) 2−Rc1/8
C-shaped stopper ring×2 L1
(Heat resistance 180℃) SWCT (Rotary Type) R
7 W （
R PT）

17.5
34.0
9.0 10.5

φE
5.0
O rings×2

L R(PT)1/8

B
φ5 φ14

φd
φD
11 （R1） M6×0.75(Fine thread)
L
φ10

φ5 R Brass (C3604)
O-ring (Fluoric rubber)
L1
C-shaped stopper ring (SUS304) In case of SWCT
R
Rotary structure allows Part Number Joint Pipe
Part Number U/Price for changing the position of
L L1 SUS304
SWCP11
Type No. 1～9 the hole on the left freely. (Threaded part one-point attachment)
Brass (C3604)
SWCP12
50 65 V O-ring (fluoric rubber) is used inside the SWCT only. Brass (C2700)
JWRH 1 Quotation V Rotary joint of the SWCT is specially structured so cannot be disassembled. SWCT12
65 100
2
V Use in atmospheric pressure 980kPa (10kgf/cm ) or lower.
Part Number U/Price 1 ～ 9
B L1 W ℓ (ℓ1) R(PT) φE φD φd Category L
● Characteristics Type No. L100 L200 L300 L400 L500
The length can be adjusted within the L ～ L1 range. 17 38 8 1/8 6.2 3 2.5 Static 11 300
Heat resistance is 180℃ , and it can be used for both cooling water and oil. 19
41
46
16
21
11
8
10
1/4 9 6 4
type
Rotary type
SWCP
SWCT
12
12
100 ～ 500
(100mm increments)
Quotation
● Notes on handling
Install it in a balanced manner. The structure have allowance of about 1mm in
Part Number － L Notes on handling
height difference between right and left. However, if it is off balance, excessive
load is applied onto the body, which may lead to water leakage. SWCP12 － 200 V Pipes are removable type. Cut it when necessary.
V Note that intermittent or continuous turning of the rotary
part of the SWCT could damage the O-ring, which results in water
■ Hydro-circuit blocks
W
Quotation leakage.
2
BRJH W1
V Use in atmospheric pressure 980kPa (10kgf/cm ) or lower.
(Heat Resistance 180℃) C2 V Use water and/or oil at temperature of 180℃ or lower.
B'

Quotation V They may interfere depending upon size of 2 joints and nipple, etc. to use.
−0.1
20 −0.3

A A'
B

A−A' cross section B−B' cross section

φ11
2.5−0.1

■Vertical use ■Horizontal use

0
16 −0.5
6.5
0

① Backup plate undercut ② Clamping plate undercut ③Attaching to cavity

8

0
3.2−0.1 8 Thick part of molded product
φ6.5 Spot cooling pipe
Finished Finished
products products
R S45C＋Nickel plated
O-ring (Fluoric rubber) Core Core
L P SCB6－20 Movable die plate
Joint
O-ring Part Number U/Price
W W1
Size Type L 1～9 P artial cooling from horizontal directions is possible if cooling of

Cooling Components
Movable die plate

Cooling Inside of Mold

Movable die plate partially-thick part is difficult.
JIS G40 95 75 50

Joints Hoses
Upper ejector plate ④Attaching to slide core
JIS G60 125 105 BRJH 80 Quotation Locking Block ・
Finished products
Slide Core
JIS G75 145 125 100 φP
2 Cooling water Back plate Lower ejector plate Cooling joints
V Use in atmospheric pressure 980kPa (10kgf/cm ) or lower. conduit Pitch B Cooling joints
②
Spot cooling pipe
Spot cooling pipe
φP6.0～7.0 is recommended hole diameter.
Part Number － L Heat resistance is 180℃, and it can be used for both Joint
Movable
JWRH1 65 cooling water and oil. clamping
－ Spot cooling pipe plate
Joint Movable die plate
BRJH50
P artial cooling is possible without By using cooling joint (JTW, etc.), cooling Joint
Quotation Quotation mechanical processing of coolant hole pipe mechanism can be attached from the
from horizontal directions. clamping plate.
 hen used for cooling of slide core, it can prevent heat expansion and
W
scraping troubles while shortening the cooling cycle.

1113 1114