Scribd
Upload
96 views4 pages

Cylinder Head - Install: Desarmado y Armado

perkins 3054

Uploaded by

Julio Meza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
96 views4 pages

Cylinder Head - Install: Desarmado y Armado

perkins 3054

Uploaded by

Julio Meza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

436C Backhoe Loader Center Pivot, Single Tilt 8TN00001-00924 (MACHINE) PO...

Página 1 de 4

Cerrar SIS

Pantalla anterior

Producto: BACKHOE LOADER


Modelo: 436C BACKHOE LOADER 8TN
Configuración: 436C Backhoe Loader Center Pivot, Single Tilt 8TN00001-00924 (MACHINE) POWERED BY 3054 Engine

Desarmado y Armado
3054 Engine for Caterpillar Built Machines
Número de medio -SENR6241-13 Fecha de publicación -01/08/2008 Fecha de actualización -04/08/2008

i01645901

Cylinder Head - Install


SMCS - 1100-012

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1

1. Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores.

Illustration 1 g00550165

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 31/10/2020
436C Backhoe Loader Center Pivot, Single Tilt 8TN00001-00924 (MACHINE) PO... Página 2 de 4

2. Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head
gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder
head gasket.

3. Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 4.

Illustration 2 g00550163

Typical example

4. Attach a suitable lifting device to cylinder head (2) .

5. Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on
dowels (4) and that cylinder head gasket (3) is positioned correctly.

6. Remove Tool (A) .

Illustration 3 g00550160

Typical example

7. Lubricate cylinder head bolts (1) with clean engine oil.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 31/10/2020
436C Backhoe Loader Center Pivot, Single Tilt 8TN00001-00924 (MACHINE) PO... Página 3 de 4

Illustration 4 g00550162

8. Gradually tighten all of the bolts (1 through 22) in a numerical sequence to a torque of 110
N·m (80 lb ft).

9. Tighten all of the bolts (1 through 22) again in a numerical sequence to a torque of 110 N·m
(80 lb ft).

10. Place an index mark on the bolts and use Tool (B) in order to further tighten the bolts. Refer
to illustration 4.

a. Turn the short bolts that are marked with an "S" for an additional 150 degrees (2.5
flats).

b. Turn the medium length bolts that are marked with an "M" for an additional 180
degrees (3.0 flats).

c. Turn the long bolts that are marked with an "L" for an additional 210 degrees (3.5
flats).

End By:

a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Install".
b. Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Install".
c. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
d. Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Install".
e. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
f. Install the inlet manifold. Refer to Disassembly and Assembly, "Air inlet Manifold -Install".

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 31/10/2020
436C Backhoe Loader Center Pivot, Single Tilt 8TN00001-00924 (MACHINE) PO... Página 4 de 4

g. Fill the coolant system. If the engine uses Extended Life Coolant (ELC), refer to Operation
and Maintenance Manual, "Cooling System Coolant (ELC) - Change". If the engine uses
Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual,
"Cooling System Coolant (DEAC) - Change".
h. Connect the electrical connections at the battery.

Copyright 1993 - 2020 Caterpillar Inc. Sat Oct 31 18:51:53 EST 2020
Todos los derechos reservados.
Red privada para licenciados del SIS.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 31/10/2020

You might also like