PROTECTIVE COATINGS

APCOTHANE CF 678
Polyurethane
PROTECTIVE, PERFORMANCE AND POWDER COATINGS

Product Description

Two component high build, high solid, acrylic aliphatic polyurethane finish with excellent weathering performance
characteristics.

Features and Recommended use

• Designed as finish coat for new construction and maintenance over most epoxy-polyurethane systems
• Excellent weather resistance in coastal and industrially polluted exposure conditions
• Excellent gloss and colour retention
• Very good chemicals and water resistance
• Excellent mechanical properties

Technical Data

Colour Range
Gloss Glossy
Volume Solids Approx. 57 %
Recommended DFT / Coat 50 - 75 microns
Theoretical Coverage Capacity 11.40 sq.mtr/ ltr @ 50 microns
7.60 sq.mtr/ ltr @ 75 microns
Drying Time Surface Dry : 90 minutes
Hard Dry : 6 hours
Full Cure : 7 days
Over coating interval Min. : 6 hours
with recommended topcoats Max. : Unlimited, provided surface is cleaned from
all contamination
Method of Application Air Spray and Airless Spray

The data given is for guideline only. The physical values are subject to normal manufacturing tolerances, colour and testing variances.
The actual drying time/ overcoat interval may be shorter or longer, depending on film thickness, ventilation, humidity, temperature etc.
The information provided above is at 30° C and 65% relative humidity.

Directions For Use

Surface Preparation

General:
• Surfaces must be dry, clean and free from contaminants
• Ensure removal of dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Oil and grease should be removed as per SSPC-SP1 solvent cleaning
• Surface should be checked and treated in accordance with ISO 8504 prior to priming

PRODUCT DATA SHEET Page 1/3 Product Data Sheet - 2585

 Primed Surfaces: :
• Suitable epoxy primer, epoxy/ polyurethane undercoat; dry & free from all surface contamination.
Apcothane CF 678 must be applied with the specified over-coating interval of the primer/ under-coat
• In case of aged epoxy coating, the surface should be sufficiently roughened prior to painting

Application Conditions

• Substrate temperature should be at least 3°C above dew point but not above 50°C
• Relative humidity should be below 85%
• Good ventilation is required in confined areas to ensure proper curing

Mixing

• Apcothane CF 678 is supplied in two packs. Stir the base and hardener separately. If settling is observed in the
base or hardener, loosen the settled material with the help of hand stirrer followed by power driven stirrer for
quick homogenous mixing
• Mix hardener gradually into the base under continuous stirring as per the mixing ratio. Once the unit has been
mixed, it should be consumed within the working pot life. In case of part mixing (which should be avoided), close
the lids of containers tightly to avoid contact with atmospheric moisture
• Thinner should be added after mixing the components and post the induction time. Addition of too much thinner
will lead to reduced sag resistance

Mixing Ratio Base : Hardener

(by volume) 5 : 1
Induction Time 15 minutes
Pot Life at 30°C 2 hours

Application

Brush / Roller
Recommended thinner T 213
Volume of thinner 0 - 10 %
Air Spray
Recommended thinner T 213
Volume of thinner 15 - 45 %
Nozzle orifice 1.5 - 3.00 mm
Nozzle pressure 0.3 - 0.4 MPa
(= approx. 3-4 atm; 43-57 p.s.i)
Airless Spray
Recommended thinner T - 213
Volume of thinner 5 – 15 %
Nozzle orifice 0.28 - 0.33 mm
Nozzle pressure 10 -13 MPa
(= approx. 100-130 atm; 1400-1800 p.s.i)

Cleaning

• Do not allow the product to remain in hoses, gun or spray equipment. Clean all equipments immediately after use
with Thinner T 141. It is recommended to periodically flush out spray equipment during the course of the working
day. The frequency of cleaning will depend on amount sprayed, temperature and time gap.
• All surplus material and empty containers should be disposed of in accordance with appropriate regional legislation

PRODUCT DATA SHEET Page 2/3 Product Data Sheet - 2585

 Product Characteristics

• DFT of 40-50 microns per coat can be achieved by brush application and 50-75 microns per coat can be achieved
by spray application. For certain shades in red, yellow and orange, by brush application, 2 coats may be required
to give complete hiding especially when applied over dark undercoats
• The gloss, sheen and finish are dependent on the application method. The best gloss and finish is achieved by
conventional spray application
• Apcothane CF 678 must be thinned with the recommended thinner only. Usage of alternate thinners will affect the
curing process
• Premature exposure to condensation and rain may cause color and gloss change

Overcoating and Topcoats

• Apcothane CF 678 can be top coated on most epoxy and polyurethane primers/ undercoats as recommended by
Asian Paints PPG representative
• Apcothane CF 678 can be top-coated with itself

PACK SIZE 20 ltrs (Base: 16.77 ltrs & Hardener: 3.33 ltrs)

Shelf Life: Atleast 9 months @ 30°C for original unopened pack,

STORAGE subject to inspection thereafter. Store in a cool, dry place and in
accordance with local regulations

Flash Point: Base - Not less than 24°C; Hardner - Not less than 24°C
REGULATORY
VOC: 380 - 410 gm/ ltr ( depending on shades ) as per USA-EPA Method 24
INFORMATION
Product Weight: 1.02 – 1.17 kg/ ltr (depending on shades)

SAFETY INFORMATION

• As a general safety measure, inhalation of solvent vapours or paint mist and contact of liquid paint with skin
& eyes should be avoided. Forced ventilation should be provided when applying paint in confined spaces or
stagnant air. Even when ventilation is provided, respiratory, skin and eye protection is always recommended
while spraying paint
• Please refer our Material Safety Data Sheet prior to using the product

Disclaimer: To the best of our knowledge the information provided herein are true and accurate at the date of issuance. Since we have no control over the quality or
condition of the substrate or the various factors affecting the use and application of the product, we do not accept any responsibility or liability arising out of use of
the product. The company reserves the right to modify data contained herein without prior notice. Any change in data would normally be followed by issue of a new
data-sheet. The user should check with the nearest sales office of the company and confirm the validity of the information, prior to using the product.

‘APCOTHANE’ is a Trademark of Asian Paints Ltd. | Licensed user: Asian Paints PPG Pvt. Limited.

Head Office: Asian Paints PPG Private Limited,Plot No-5, Gaiwadi Industrial Estate, Near Religare Building, S.V. Road, Goregaon (W),
Mumbai 400 062. Tel No: 022 61089800, Email: [email protected], Website: www.asianpaintsppg.com

February 2013 Page 3/3 Product Data Sheet - 2585