Scribd
Upload
87 views2 pages

PRX20 M

The PRX20/M is a smart card reader that can read Mifare cards from 2-5cm away. It operates from 6-12V and outputs data in Wiegand 26-bit, Wiegand 34-bit or clock and data formats. It has LED indicators for power, read status and errors. Installation involves connecting the reader's wires to a controller using the provided wiring diagram and mounting the small reader on a wall or panel using the included screws.

Uploaded by

Flavio Miranda Gonzalez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
87 views2 pages

PRX20 M

The PRX20/M is a smart card reader that can read Mifare cards from 2-5cm away. It operates from 6-12V and outputs data in Wiegand 26-bit, Wiegand 34-bit or clock and data formats. It has LED indicators for power, read status and errors. Installation involves connecting the reader's wires to a controller using the provided wiring diagram and mounting the small reader on a wall or panel using the included screws.

Uploaded by

Flavio Miranda Gonzalez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Introduction Output formats:

1. Clock & Data ABA (10 char)


The PRX20/M is a high performance Mifare smart card reader with
2. Standard Wiegand 26 bits
medium range and small dimensions. The unit runs on any voltage
3. Wiegand 34 bits output format interface
from 6~12 V (DC).
TTL outputs: up to 15m.
Dimensions L120x W45x H21 (mm)
Note: In case of reading errors, 1K ohm pullup resistors can
Weight 300g be added to the Data and Clock outputs (brown and
Ambient Temperature Operating temperature: -10C ~ +55C; blue wires).
Storage temperature: -10C ~ +60C; Operating state: sound-visual state indication
Interface Cable 50 cm
Light Indications
Power Requirements 6~12 Volts regulated DC at 80 mA.
A linear regulator is recommended. Model: PRX-20/M
Interface Wiegand 26,Wiegand 34, Magstripe. Indication Color
Typical Maximum Range 2~5 cm at 6~12V with Mifare card Power on Yellow Standby
Read (In ideal conditions). OK indication Green + 1 beep activated by controller
Frequency 13.56MHz standard Error indication Red + 3 beeps
Transponder Read Only
(For Unique Serial Number/Unique Wiring
Identifier)
Wiring color Function
Audio/Visual Internal LED and Buzzer which may
Indication activated externally only. Red DC 6V-12V

Output stage -internal circuit configuration Black GND


Brown Data0/Data Wiegand Output Format
VCC Blue Data1/Clock D0 and D1 output “0” and “1” respectively.
Orange Green LED When outputting “0”, D0 experiences a negative pulse and when
PRX20/M 1K outputting “1”, D1 experiences a negative pulse.
Pullup for output Gray Red LED See the following diagram displaying a negative pulse width of
( Brown ) White Buzzer TP=100+10 microsecond; with a repetition period of
( Blue ) TW=1000+100 microsecond and 1 microsecond=1/1000000 a
Green Se1_EX Output Format wire #1 second.
Purple Se2_EX Output Format wire #2

Type of cards
MF card* reading distance: 20-50mm (subject to quality of card).
* Any card of 64bit memory array used by H4001 CMOS
integrated circuit, by EM Microelectronic-H4100/4102 or
compatible.

Synel MLL Payway Ltd. Synel MLL Payway Ltd. Synel MLL Payway Ltd.
Output options
Se1_EX=1, Se2_EX=1 ABA Synel (10 char)
Se1_EX=0, Se2_EX=0
Se1_EX=1, Se2_EX=0
Std. Wiegand 26bits
Wiegand 34bits
PRX-20/M
Note:
1. Se1_EX=1 or Se2_EX=1 is a free wire, not connected to any
Card Reader
wires.
2. Se1_EX=0 or Se2_EX=0 is a wire connected with GND.
Decoding
User Manual
Mifare's serial number is a 32 bit binary string (represented by 4
Hex bytes).
PRX20/M reader decodes the number in different ways according 7. Connect wires between your PRX-20/M card reader and the
to the selected output format. One parity is added automatically at controller.
the beginning and end of the serial number. Note: To boost the signal it is recommended to use both pull-
1. ABA 10 char – all 4 bytes are converted to a deci- up resistors when the distance between the reader and
the controller is longer than 5 meters.
mal value.
8. Turn on the power to test. When the power turns on screw the
For example: 93 D7 79 A6 (Hex) are converted to unit into place.
2480372134. Use a 24 AWG parallel cable. Do not install in a wire casing
2. Wiegand 26 bit: The last 3 bytes of the serial num- with strong current power cords.
Do not expose to direct sunlight, high temperatures, or strong
ber are sent with additional parity bits. electromagnetic interferences.
For example: 93 D7 79 A6 (Hex) only D7 79 A6 (Hex) is If installed outdoors, a lightning protective device may be
necessary.
sent + 2 parity bit according the standard.
3. Wiegand 34 bit: the last 4 bytes of serial number are Packing List
converted with additional 2 parity bits. The following items should be found in the PRX-20/M package:
For example: 93 D7 79 A6 (Hex)- Parity bit + 93 D7 79 A6 • Color external packing carton with bar code mark, grey/black
internal packing box
(Hex) + parity bit according to standard.
• 1 PRX-20/M (with model bar code and date of production)
Installation • Fixing rubber plug and tapping screws: 1 set
Do not mount on a metal panel. • Instruction leaflet: 1
4. Select a location to install the PRX-20/M card reader. The rec- • Warranty Card and Quality Certificate: 1
ommended height for installation is 1.4m. Cat. no.: 430110
5. Prepare an outlet hole (of 15mm) in the installation pane. Document no.: PRX20M-222-01
6. Drill two 6mm fixing holes to wall and place fixing rubber Dated 23.6.2013
plugs into the holes.

SYNEL MLL Payway LTD.


Yokneam Industrial Park, 2 Hamada St.,
POB 142, Yokneam 2066719, Israel
Tel: +972-4-959 6777 Fax: +972-4-959 0887
Synel MLL Payway Ltd. Synel MLL Payway Ltd. www.synel.com

You might also like