OPERATOR’S INSTRUCTION

MANUAL

INTELLISCAN SAFETY ZONE

Multi-Zone Walk-Through Security Metal Detector

Ranger Security Detectors, Inc.

11900 Montana Avenue
El Paso, TX 79936

Telephone: (915) 590-4441

Fax: (915) 592-1043
Web site: www.rangersecurity.com
E-mail: [email protected] Version 9.9

1
 CONTENTS
Intelliscan Safety-Zone Specification Section 1.0

Parts List and Diagram Section 1.1

General Description Section 2.0

Assembling and Wiring the Intelliscan Safety-Zone Section 3.0

Site Selection Section 4.0

Using the Intelliscan Safety-Zone Section 5.0

Keypad layout Section 6.0

Visual Display Panel Section 7.0

Adjusting Operating Parameters Section 8.0

Using Keypad and L.C.D. Display Section 9.0

Main menu Selections Section 10.0

Program Settings Section 10.1
Menu Definitions Section 10.2
O.T.P. Security Level Section 10.3
Suggested Parameters for O.T.P. Security Level Section 10.4
F.A.A Three Gun test Security Level Section 10.5
Suggested Parameters for Three Gun Security Level Section 10.6
Higher Security Weapons Detection Section 10.7
Suggested Parameters for Higher Security Weapons Section 10.8

Industrial Applications Section 11.0

Eliminating False Alarms Section 12.0

Operating Multiple Detectors in Parallel Section 13.0

Achieving Uniform Detection Section 14.0

Support Floors with Excessive Structural Metal Section 15.0

Horizontal Axis Gain Control Section 16.0

Advanced Features: Detection Enhancement Section 17.0

Need For Detection Enhancement Section 17.1

Maintenance and Repair Section 18.0

Warranty Section 19.0

2
 IMPORTANT:
If you have received a consignment of more than one detector please insure
that the Side Panels are matched to the correct Header Assembly. Serial numbers
are written on the packing cases and on identification labels attached to top Side
Panels and Header.

For information on general metal detection techniques and operating

procedures please refer to our web site at; www.rangersecurity.com (see
“Understanding Basic Metal Detection Listed on Information page.

1.0. INTELLISCAN SAFETY-ZONE SPECIFICATION

Dimensions:
Archway inside- 30 Inches Wide 80 Inches High 20 Inches Deep
Overall outside- 35 Inches Wide 87 Inches High 20 Inches Deep

Regulatory Standards:
The Intelliscan Safety-Zone is certified by the U.S. Federal Aviation Administration, and
meets or exceeds all requirements of the National Institute of Law Enforcement and
Criminal Justice (N.I.L.E.C.J.) standard 0601.00 security levels 1-5.

Electronics and Electromagnetic:

The Intelliscan Safety-Zone is processor based and features true multiple-zone
performance. The archway passage consists of eighteen separate zones. It combines
unique multiple independent sensors with high speed digital processing. A built in
display panel provides instant visual identification of the exact location of a suspected
weapon, or weapons, in the archway area.

Detection Programs.
The Intelliscan Safety-Zone has 20 detection programs. They have been designed for
both weapon screening and asset protection applications. The weapon screening
applications are designed for various threat levels and provide good detection of ferrous
and non-ferrous metals.

Header Assembly, Control Panel and Display

The Control Panel at the front of the Header Assembly contains an on/off Key switch, a
built in Alarm Display Panel, an L.C.D. Display Panel that shows system operating
parameters, and Keypad for operating parameter data entry. The built in Alarm Display
Panel depicts the area within the archway opening. It has an L.E.D. alarm showing the
detection zones. A twelve-segment bargraph display shows an object’s signal strength in
real-time. Also included are red Alarm events L.E.D. a green Ready L.E.D. and yellow
Wait L.E.D. all electronics are housed in the Header Assembly.

3
System Throughput:
The Intelliscan Safety-Zone accommodates a wide range of walk-through transit speeds.
Rapid automatic reset maximizes the system throughput rate to over fifty passes per
minute. Intelliscan’s speed range provides consistent detection over a wide range of
object transit speeds.

Interference immunity:
Intelliscan Safety-Zone advanced design provides excellent interference rejection.
Outside interference from sources such as computers, fluorescent lights, etc., have
minimal impact, enabling the unit to operate in environments that render many units
inoperable.

Uniform Detection:
The field of detection is uniform from top-to-bottom with no hot spots or dead spots. In
situations where large amounts of steel re-bar exist in a support floor and cause a drop in
detection at ankle height: adjusting the sensitivity of the floor level zone can compensate
the loss. Normal operation can be achieved even when excessive amounts of metals are
present. The sensitivity of the six horizontals zones can be adjusted independently. They
allow uniform detection to be maintained in all regions of the detector. Horizontal Axis
Gain Control compensates for detection losses caused by external metal in walls or
furniture. It adjusts the sensitivity horizontally across each zone.

Multiple Operating Frequencies:

The Intelliscan Safety-Zone provides eight user selectable operation frequencies
allowing simultaneous operation of multiple units without interconnecting slaving cables.

Memory:
The Intelliscan Safety-Zone utilizes an embedded microprocessor. Whenever adjustments
are made to the operating parameters they are automatically retained in memory. When
the detector is powered down the previously entered operating parameters are retained in
memory.

System Security:
Intelliscan Safety-Zone is pass-code protected and has a locking key switch that connects
the AC power. A six digit pass code must be entered before operating parameters can be
changed.

Construction:
The Intelliscan Safety-Zone is coated in a durable resistant Formica finish. The Side
Panels and Header Assembly are sturdily constructed for stability and durability.

System Diagnostics:
The Intelliscan Safety-Zone has self-diagnostics test routines. When the unit is powered
up it automatically self-test and calibrates itself to the surrounding environment. Periodic
calibration is not needed.

Electrical:
The Intelliscan Safety-Zone’s Universal Power Supply operates off voltages in the range
115-230VAC / 47 to 63Hz.

4
Operating Environment:
Indoor operation from 0C to +55C. Humidity to 95% non-condensing

Weight:
140lbs (63.6 Kg)

5
1.1 PARTS LIST AND DIAGRAM

Parts List:
1. Header (Electronics enclosure)
2. Side Panel A
3. Side Panel B
4. (8) Flat Washers
5. (8) 2 ½ Socket Head
6. (8) 5/8” Plugs
7. Ten Foot Power Cord

Parts Diagram:

6
2.0GENERAL DESCRIPTION OF INTELLISCAN SAFETY-ZONE

The Ranger Intelliscan Safety-Zone uses a unique Continuous Wave Multiple Sensor
Technique. An embedded processor analyzes data from multiple individual sensors. An
Alarm Display Panel depicts the archway opening, showing two separate detection zones
within the opening. The two zones are monitored individually and typically, when used
for weapon screening, detect a metal mass the size of a weapon before alarming. This
substantially negates the problem of small amount of harmless metal, such as key and
coins, causing an unwanted alarm. Security personnel can pinpoint the exact location
within the archway where a weapon-sized object is being carried. If more than one
weapon is carried the location of each is displayed.

The ground zone can be used to accurately compensate for signal losses caused by
structural metal in a support floor. This independent adjustment eliminates the need to
increase the overall sensitivity of the detector. In contrast, when a conventional detector
is operated on a support floor containing re-bar its overall sensitivity must be raised to a
level where detection occurs at floor level. This overall increase in sensitivity causes the
upper region of the detector to become overly sensitive and unwanted alarms occur.
Intelliscan’s fully adjustable floor control enables uniform detection to be achieved
throughout the detector as the upper zone can be operated independently at normal
sensitivity levels. Intelliscan Safety-Zone’s Multiple Zone Detection increases the
throughput rate of people being screened. A decrease in unwanted alarms from harmless
personal metal objects; coupled with the ability to identify the location of weapon sized
objects both increase screening efficiency. Traffic flows faster and more smoothly
because of the lower incidence of unwanted alarms. Also, when an alarm does occur the
guard can immediately target the suspect object. Screening speed, accuracy, and quality
of security are all enhanced.

The Intelliscan Safety-Zone uses self-diagnostics that monitor electronics; environmental,

interference and metal overload conditions. The alarm Display Panel includes a twelve-
segment signal strength bar graph that provides an indication of sized object and strength
of external interference.

Intelliscan eliminates common detector problems such as false alarms, uneven detection,
and inconsistent operation. The super performance of the Intelliscan Safety-Zone benefits
everyone – security personnel have a lower workload, the public suffer less delays the
purchaser enjoys higher quality surveillance.

*NOTE: it is imperative
That the serial numbers on the header
& side panels A & B all match,
As each unit is calibrated with
the specific matching set of side panels
And headers and mix-matching
them may cause Dead spots
(non-detecting spots) or erratic operation.

7
3.0 ASSEMBLING AND WIRING THE INTELLISCAN
SAFETY-ZONE

The two packing cases contain two Side

Panels, a Header Assembly, eight Allen bolts
with washers and a wrench, two keys and a
power cord. The Side Panels have
identification labels screwed onto their top

Surface Panel “A” is positioned on the left of

the Header Assembly. Lay the two side panels
with their silver connector sockets facing
upwards. Ideally, assemble the unit close to the location where it to be used. The Header
Assembly should be placed between the side panels.

Figure 2.

And with its Control Panel facing upward. Turn Side Panel “A”, trough 90 degrees so the
top socket is facing the Header Assembly, see Figure 2. Align the top of the Side Panel
with the top of the Header Assembly and insert the Header Assembly interconnection
cable firmly into the Side Panel Socket. Tighten the connector’s securing screws. Next,
insert the four Allen Bolts, with washers, into Side Panel and start screwing them into the
Header Assembly. Do not tighten the bolts at this stage. Repeat the above exercise with
Side Panel “B”. In addition to the Side Panel interconnection cable there is a power cord.
Both connectors should be firmly seated in the Side Panel sockets. Again, secure the Side
Panel to the Header Assembly. When all eight bolts are engaged start tightening them so
that the Side Panels are firmly secured to the Header Assembly.

8
Please Note: when the unit leaves the factory the power cord is configure to connect to
Side Panel “B”, see Figure 3. if the wall AC power outlet is situated adjacent to Side
Panel “A”, it is necessary to re-route the Header Assembly power cord. First, Remove
the Header Assembly’s top access panel. The black power cord should be moved from
the right-hand to the left-hand bulkhead compartment and inserted into Side Panel A’s
power socket. Figure 4 refers.

One the Side Panel have been secured, raise the unit to the upright position and connect
the power cord into the outer surface of the appropriate Side Panel. Again, check bolts re
tight.

4.0. SITE SELECTION

CHOOSE YOUR INATALLATION CAREFULLY! The Intelliscan Safety Zone should

be installed on a level, solid floor. There should be no large metal objects within 3 feet of
the unit. Intelliscan is designed to detect metal that is moving, hence, closely spaced large
metal objects such metal clad doors, passing metal carts or fork lifts, etc. will cause an
alarm event. Choose your installation site carefully to minimize disturbances from large
moving metal objects in the surrounding area. Likewise, care should be taken not to
position the unit too close to walls which contain rebar construction or conduit. If
the unit must be used near stationary metal the Horizontal Axis Gain Control feature can
be used to compensate for signal losses. Use a Model 1000 Hand scanner to scan walls
for the presence of substantial amount of metal.

Plan screening area with enough room to accommodate people waiting to pass through
the unit, space for operators, and a non-metallic table for depositing objects removed
from pockets and area for hand scanning. Make sure the unit will not get exposed to rain,
mist or condensation. Insure the power cord is routed away from pedestrian traffic.

9
5.0. USING THE INTELLISCAN SAFETY ZONE

Intelliscan has Alarm Display Panel with an L.E.D. array, an L.C.D. alpha-numeric
display and a 20 button Keypad. The L.C.D. display and keypad allow the user to adjust
operating parameters and to tailor the unit’s operation to meet his/her specific security
requirements. The Alarm Display provides information on alarm events, signal strength,
and abnormal conditions such as high noise and / or metal overload conditions.

Turn the unit on by inserting the key into the Key switch and turning it clockwise. All the
L.E.D. elements light up in sequence one at a time. The L.C.D. Panel displays a SELF-
TEST message while a self-diagnostic test is in progress. Next it reads CALIBRATION.
During this period the unit calibrates itself to its surrounding environment (always keep
moving metal objects and people clear of the unit when it is undergoing calibration.)
If any disturbance to the surrounding environment occurs during SELF-TEST or
CALIBRATION (e.g. a metal cart is moved by the unit, person touches the unit, person
walks through it, etc.) the unit must be returned to SELF-TEST mode. To reset, press the
“Rst” (Reset) key on the Keypad. Alternative, turn the AC power off and then back on; it
then automatically self-test and recalibrates.

When the unit has completed testing and calibrating the L.C.D. continuously scrolls and
shows: program, volume and version number. Intelliscan performs all normal screening
operations in this operating mode. Adjustments to the operating parameters settings
cannot be made in this program mode; for example, sensitivity values cannot be accessed.
Security screening should always be performed in this mode.

Operating parameters can only be accessed by an authorized person. Entry into the
operating menu is gained by entering a six-digit pass-code via the keypad. If, after
accessing the menu no keypad changes are made within a five minute period, access to
the operating parameters is automatically terminated. The default pass-code key strokes
are 1, 2, 3, 4, 5, 6 and Ent (Enter).

10
6.0 KEYPAD LAYOUT

Select (M↑) Tabs down though the menu in forward direction

Select reverse (M↓) Tabs through the menu in reverse direction

Backspace (Bks) Deletes what has been typed; allows for corrections.

Nominal (Nom) Resets the settings to the nominal operating parameters (original
operating values set at the factory)
Escape (Esc) Escapes from the scrolling menu program and back to the normal
operating mode

Reset (Rst) Recalibrates the unit.

Negative (-) adds a negative value to a number (e.g. used to lower zone
sensitivity settings).
Increment and
Decrement
(Inc) (Dec) used to adjust single digits settings. (Inc). For up and (Dec) .for
down.

Enter (Ent) To enter a parameter value.

Numerals. 0. through 9.

11
VISUAL DISPLAY PANEL

1. Twelve segment real-time signal strength bargraph – shows signal strength of

objects that pass through the archway. Signal level rises as metal is inserted. If the
signal level rises into the red area the unit alarms. Number of bars that are
illuminated is proportional to object size.

2. Alarm indicator light for upper zone (red L.E.D) – lights and is accompanied by
an audio alarm when a weapon or contraband size object is detected.

3. Alarm indicator light for floor zone (red L.E.D) – lights and is accompanied by an
audio alarm when a weapon or contraband size object is detected.

4. Ready indicator light (green L.E.D) illuminates when unit automatically resets
and is ready to screen next person.

5. Wait indicator light (yellow L.E.D.) lights when unit is self calibrating, working
on main menu or goes into noise or metal overload fault condition.

12
8.0. ADJUSTING OPERATING PARAMETERS

All adjustments to the operating parameters are entered via the Keypad and viewed
on the L.C.D. Display panel. A pass-code is needed to access the program prior to
making parameter changes.

All operating parameters in menu have a preset value (nominal value). The nominal is
a pre-set factory adjustment and should only be considered as a starting point.

9.0. USING THE KEYPAD AND L.C.D DISPLAY

L.C.D. Display shows version number, program, volume level and sensitivity level

Press keys 123456 an Ent. After entering pass-code, select (M↑) or (M↓) to
scroll thru menu. M to select appears on the L.C.D.
menu.
Push (M↓) select PGL Threat Aviation current 1 new * appears on
the L.C.D. Any of the 20 programs can be selected.
(See: section on program settings)

Push (M↓) select Baseline sensitivity current 35% new * appears on

the L.C.D. Select new sensitivity.

Push (M↓) select Alarm tone 1-3 current 2 new * appears on the
L.C.D. select new tone.
Push (M↓) select Alarm Volume 0-7 current 4 new * appears on the
L.C.D. select new volume.

Push (M↓) select Alarm hold 1-99 current 1 new * appears on the
L.C.D. select new, this selects the time the alarm
zone light stays on.

13
 10.0. Main Menu Selections
Program – Sets the desired program. Programs 1 -12 factory set values, 21 – 24 users defined.
Baseline Sensitivity – Sets 6 horizontal zones to same baseline setting.
Alarm Tone – Sets the frequency of the audio alarm.
Alarm Volume – Sets the volume level of the alarm tone.
Alarm Hold Time – Sets the time duration of the LED indication of the alarm.
IR Sensor – Enables/Disables the intelligent IR Sensor.
Target Filter – Sets Low frequency filter values (0-8).
Skew Frequency – Sets the unit frequency (1-8).
Wide Mode – Sets unit for 36 inch wide unit.
Zone Settings – Sets gain in each of 2 horizontal zones.
IDC Parameters – Displays discrimination values of individual targets.
HAGC Settings – Allows user to access Horizontal Control.

10.1. Program Settings – This allows selections of programs 1- 24 as defined below:

Program 1 - Low threat Aviation

Program 2 – Medium threat Aviation
Program 3 – High threat Aviation

Program 4- Low threat Federal Buildings

Program 5 – Medium threat Federal Buildings
Program 6 – High threat Federal Buildings

Program 7 – low threat prisons

Program 8 – Medium threat prisons
Program 9 – High threat prisons

Program 10 – Low threat Public Areas

Program 11 – Medium threat Public Areas
Program 12 – High threat Public Areas

Program 13 – all metal no boost

Program 14 – all metal low boost
Program 15 – all metal medium boost
Program 16 – all metal high boost

Program 17 – Suppress positive values for IDC

Program 18 – Suppress negative values for IDC

Program 19 – copper
Program 20 – aluminum

Program 21 – User definable

Program 22 – User definable
Program 23 – User definable
Program 24 – User definable

14
10.2. Menu Definitions

Baseline Sensitivity – Sets unit sensitivity range between 1 (minimum) and 99 (highest)

Alarm Tone – Sets the frequency of the alarm to 500,100 or 1500 hertz.

Alarm Volume – Sets the volume of the alarm in steps between 0 and 7.

Alarm hold Time – Sets the time the LED alarm indication is on after an alarm. This value is
between approximately 1 second and 99 seconds. This function is disabled if the IR Sensor is set
to 1.Or on.

IR Sensor – Enables or disables the intelligent sensor. This activates the unit for a short time
while the person is passing through the detector. If your installation is near an elevator, moving
door, or large moving objects, which trigger the unit, you may want to consider this approach.
“This function only works with unit equip with a sensor.

Target Filter – Sets the amount of low frequency filtering needed to reduce noise in the target
spectrum.

Skew Frequency – Sets the unit in different frequencies in order to work with multiple units.

Wide mode – Enables or disables the wide mode of operation. This is use on detectors with wider
than the normal 30 inches distance between side panels. This is only when order a wide unit.

Zone Settings – Sets the amplification/ attenuation of the 2 horizontal zones. This is the same as
the IDC values, 1 to 99 is amplification, and -1 to -99 is attenuation.

IDC Controls – This is a feature to help the customer, which has a need to build their own
program to detect, or not detect, a particular object. Each object, when passed though the detector,
shows positive and negative numbers. This is due to the signals going positive and negative.
Ferrous and Non Ferrous materials will go in opposite directions when passed to the middle of the
detector. Programs 17 and 18 are to enable only one reading on the display to enable the user to
set values they want to enhance or reduce. Each program can have up to 7 “windows”, each being
a different target if so desired. Each window has a center value, a window with value, and an
amplifier/attenuator value. When the object is passed to the center, the display will show side A,
side B, and Mass. Usually if the object gas a mass value of 150 or more, side A and B will be
very close to the same number. Smaller object may have to be passed closer to one side, therefore
making the farthest side reading somewhat unstable. This is normal and not to be concerned.
Using the number of the closest panel, this is the IDC center value. Make 5 or 6 passes with the
object in different orientations and record the values. Subtract the lower from the higher value
and add 5 counts. This should be close to the needed window value. If you want to alarm on this
target the AMPLITUDE value will be a positive number between 1 and 99. To attenuate the
object the number will be between -1 and -99. Be careful about killing targets entirely!!! If you
desire you can pick a program, which is close to the setting you need and view the settings, then
change the settings and save the program as one of the user programs.

HAGC settings – Horizontal Amplification Gain Control is for setting gain on each coil
independently. There are 12 coils, 6 per side locate in 6 zones. A1-A6 and B1-B6 allows setting
the amplification/attenuation of each coil with the same 1 to 99, -1 to-99 values. This is to
compensate for nearby objects, which only affects some areas of the detector.

15
10.3. O.T.P. Security Level

The Operation Test Piece (O.T.P.) simulates the detection response from a small revolver, and is
manufactured to the specifications of the U.S. Federal Aviation Administration. The O.T.P.
should be carried with its barrel down and butt to the right. The O.T.P. must be detected 100% of
the time as the person walks though the unit. This security level is average, and is considered
adequate by many security managers for general public weapon screening Suggested settings are
shown below.

10.4. SUGGESTED PARAMETERS FOR O.T.P. SECURITY LEVEL

Program (PROGRAM=) 1
Baseline Sensitivity (SENS=) 20 to35%

A small adjustment to baseline sensitivity may be required because of location variables. If

support floor contains re-bar, Zone 6 sensitivity will have to be increased to a level where O.T.P.
is detected at ankle level. Refer to Section 14 to 16.

The FAA Operational Test Piece may be purchased from:

Larry Copello, Inc.
1239 Rollins Rd.
Burlingame, CA 94010
Tel (415)579-0256
Fax (415)579-0257

10.5. F.A.A. THREE GUN TEST SECURITY LEVEL

The U.S. Federal Administration three gun test uses three different small handguns of varying
characteristics and the O.T.P. to set detection levels. Multiple passes are made through the
detector with the various weapons at ankle height, waist height, and at shoulder height (a total of
36 passes.) Information on the F.A.A. test procedure may be obtained from:
Federal Aviation Administration
800 Independence Ave. SW.
Washington, DC 20591

10.6. SUGGESTED PARAMETERS FOR THREE GUN SECURITY LEVEL

Program 1 or 2
Baseline Sensitivity 35 to 50%

10.7. HIGHER SECURITY WEAPONS DETECTION

The security level includes the detection of a variety of small handguns and most Knives.

10.8. SUGGESTED PARAMETERS FOR HIGHER SECURITY WEAPONS

DETECTION

Program 3
Baseline Sensitivity 35 to 70%
As baseline sensitivity increases so does security level.

16
11.0. INDUSTRIAL APPLICATIONS

When people being screened wear footwear with steel protection in the toe caps; reduce
zone 6 (floor Zone) sensitivity to avoid unwanted alarms.

12.0. ELIMINATING FALCE ALARMS

False alarms can be defined as alarms events that occur when no one is near the detector.
These events are caused by external electromagnetic interface of a frequency comparable
the operating frequency of the detector. In practice, the detector interprets the interference
as a signal caused by metal.

The operating frequency can be change by changing the values of Skew Frequency.
There are 8 different combinations of frequencies from 1 to 8.

13.0. OPERATING MULTIPLE DETECTORS IN PARALLEL

If multiple detectors must be operated in parallel it is necessary to operate them at

different frequencies. Power-up one unit at a time. If first unit is operating in a stable
fashion turn-on the second unit. If no interaction occurs turn the third unit on. If one of
the units interacts change the unit frequency.
Try to maintain a physical separation of three feet (0.9 meters) or more.

14.0. ACHIEVING UNIFORM DETECTION

Achieving uniform detection is very important as it reduces unwanted alarms. To test

uniformity use tests object such an OTP or a 2 inch steel ball bearing. If an OTP is used,
hold it consistently in a barrel down butt right orientation. Pass the chosen object through
the left, center and right sectors of each zone and check that consistent detection is
achieved. If non-uniformity exists, adjust zone sensitivities using the following
procedure:

14.1) For Zone settings go to Zone settings and press ENT. Adjust each Zone for best
detection.
14.2) For individual Zone adjustments go to HAGC and select from Zone A1 to B6.
Zone A1 to A6 is the left side facing the metal detector from the front. Zones B1 to B6 is
the right side panel.

17
15.0 SUPPORT FLOORS WITH EXCESSIVE STRUCTURAL STEEL

Excessive amounts of structural steel in floor or ceiling can rended a conventional

detector inoperable. Multi-zone detector is designed to scope. This changes situation
sometimes exist in building that have extra steel reinforcing to support upper level
parking. Other examples are buildings that have been designed to withstand explosive
blast.
If a floor contains excessive amount of metal the weapon or test object will not be
detected at ground level. It may be possible to achieve detection by simply increasing the
sensitivity of Zone 2 to a high positive value. Incrementally increase Zone 2 sensitivity in
5% steps and check if weapon/ test object is detected at each step.

16.0 HORIZONTAL AXIS GAIN CONTROL

Section 14 and 15 describe how zone sensitivities can be precisely adjusted to compensate for magnetic
field distortions caused by structural steel in support floor. Adjust the Zone sensitivities is equivalent to
applying vertical axis gain control. Similar distortions occur in the horizontal axis if the detector is
positioned close to a steel support beam or furniture made from metal. The external metal causes the
detection response to be increased on the side of the archway near the metal and to be decreased on the
opposite.
Note ideally, the best solution is to operate the detector away from external metal
object; however, not all security locations permit this.

17.0 ADVANCED FEATURES: DETECTION ENHANCEMENT OPTION

Intelliscan can be equipped with an optional metal identification function (IDC) and
Equalization Channels that can selectively manipulate the detection response of specific
metal objects or materials. For example, a manufacturer that produces aluminum alloy
products can increase security by using Equalization channels that selectively enhance
the detection response from objects manufactured from aluminum. At the same time,
ferrous material can be discriminated against. See IDC controls.

17.1 THE NEED FOR DETECTION ENHANCEMENT

In theory, a “perfect” metal detector generates an identical detection response for all
objects of the same size and shape irrespective of their metal composition. In reality,
metal detectors respond differently to signal originating from objects made of different
metals. The situation is further complicated when an object is made from a combination
of ferrous and non-ferrous metls. Metal characteristics such as permeability, conductivity,
thickness of material and heat treatment all influence the way in which metal objects
interact with a detector. Detection is also affected by the shape and surface area of the
object and orientation which it is carried.
From an operating perspective, the above characteristics mean that variations in metal
compositions can produce some unpredictable results. For example, a small handgun may
generate a much stronger detection response than a weapon that is physically much
larger.

18
18.0 MAINTENANCE AND REPAIR

There are no user adjustable controls inside the unit. If equipment fails to perform
properly contact the factory technical support department at 1-800-852-8266. equipment
repair should only be performed by a qualified trained technician.

RMA
Return Merchandise Authorization (RMA)
1. Contact Ranger Security Detectors, Inc
2. An RMA Number is required for any repair or returns.
3. RMA Number must be identified on outside of box/package.
4. Merchandise will not be accepted without an RMA.

19.0 WARRANTY

Ranger Security Detectors, Inc. warrants the Intelliscan Safety-Zone against defects in
workmanship or materials, under normal use, for a 2 year period from the date of
purchase to the original user. Liability in all events is limited to the purchase price paid.
Liability under the aforesaid to Ranger Security Detectors El Paso factory. Ranger
Security Detectors, Inc. Warrants the Intelliscan Safety-Zone against defects in
workmanship.

19