OPERATOR’S MANUAL & PARTS LIST

175 RPM, 1 HP models - C131-7 C171, C201

175 RPM, 1.5 HP models - C171HP, C201HP
Sander, 175 RPM, 1.5 HP models - C171SD
175 - 320 RPM, 1.5 HP models - C202

WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL

COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
©Tacony, Inc., All rights reserved
X8692 06/2020

Save These Instructions

Your new Powr-Flite floor machine will afford you many years of trouble-free operating
satisfaction provided it is given proper care. Prior to packaging, your Powr-Flite floor machine
was inspected by a Quality Control Technician.

UNCRATING
Your Powr-Flite floor machine was protectively packed to prevent damage in shipment. We
suggest that upon removing the unit from its carton, you carefully inspect it for any possible
damage in transit. If damage is discovered, immediately notify the transportation company who
delivered your machine. As a manufacturer, we are unable to act upon any claim for concealed
damage; you must originate the claim.

IMPORTANT SAFEGUARDS
This machine is designed to be safe when used to perform the functions specified in this
Operator’s Manual. Should damage occur to electrical or mechanical parts, Prior to further use,
the machine should be repaired by the manufacturer or competent service center to avoid further
damage to the machine or physical injury to user. Your floor machine is equipped with a safety
switch lockout device designed for your safety. Do not attempt to bypass or defeat the safety
lockout device. Never use any device to lock the power switch triggers in the ON position.
This appliance must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk electric shock. This machine is
equipped with a cord having an equipment -grounding conductor and grounding plug. The plug
must be inserted into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING: Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it
will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 115-volt circuit, and has a grounding plug that looks like
the plug illustrated in sketch A

2
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS UNIT
Read and understand this owner’s manual and all labels on the unit before operating. Safety is a
combination of common sense,staying alert and knowing how your unit works. Use this unit only
as described in this manual. Use only manufacturer’s recommended attachments. To reduce the
risk of personal injury or damage to your unit use only recommended accessories.
WARNING: The operator must have training in the operation of this machine before using it.

WARNING: Machines can burn flammable materials and vapors. Do not use this machine with or
near fuels, grain dust, solvents, thinners or other flammable materials.

WARNING: Do not operate this machine unless it is completely assembled.

WARNING: Do not use this machine as a step or to move furniture.

WARNING: When disconnecting power cord from electrical outlet, grasp the plug. Pulling it out
by the cord itself can damage cord insulation and internal connection to plug. To prevent electric
shock, always remove the electrical plug from the electrical outlet before doing any repairs or
maintenance to this machine.

WARNING: To prevent injury, always remove the electrical plug from the electrical outlet before
changing the polishing pad and before leaving the machine.

WARNING: To prevent injury, keep hands, feet and loose clothing away from the rotating pad.

WARNING: Maintenance and repairs must be done by authorized personnel only.

WARNING: Keep all fasteners tight. Keep adjustments according to specifications.

WARNING: Keep the electrical parts of the machine dry. For storage, keep the machine in a
building.

WARNING: Always use a three-wire electrical system connected to the electrical ground. For
maximum protection against electric shock, use a circuit that is protected by a ground fault
circuit interrupter. Consult with your electrical contractor.

WARNING: To prevent damage to the power cord, do not let the pad, pad driver or wheels touch
the power cord when the machine is running. Always lift the power cord over the machine.

WARNING: Make sure all labels, decals, warning, cautions and instructions are fastened to the
machine.

WARNING: Do not leave machine running unattended.

3
 FLOOR MACHINE APPLICATIONS
• Spray buffing with red spray buff pad and spray buff chemical.

• Dry buffing a buffable finish with a tan, beige or white pad or brush.

• Scrubbing with green or blue pad or scrubbing brush.

• Stripping with a black pad and a stripping chemical.

1.5 HP MODELS ON CARPET

• Bonnet cleaning with a yarn bonnet and carpet maintainer chemical.

• Shampooing using a showerfeed shampoo brush and solution tank mounted to the handle
tube containing carpet shampoo.

1.5 HP MODELS
• Scraping with an attachment tool to remove heavy industrial deposits and residue or to
prepare a foundation for installation of carpet.

• Wire brushing of concrete floors.

• Sanding with very aggressive sandpaper or sand screen discs.

• Carpet restoration where shampooing & pile lifting require very stiff brush bristles.

PREPARING THE MACHINE

To attach the drive block or brush or other attachment, be sure the
handle is “locked” in the upright position. Lay the floor machine on its
back with the handle lying on the floor, this exposes the driving plate
on the underside of the floor machine. Holding the drive block, brush or
attachment in both hands and straddling the motor with your back to the
handle box, bend over and fit the three slots of the clutch plate (built into
the back of the brush) over the three lugs of the driving plate. Turn the drive
block, brush or attachment counter-clockwise as far as it will go until it is
seated in the ready-to-use position.
CAUTION: This is the only proper way to install a drive block, brush or
attachment. NEVER put a drive block, brush or attachment on the machine
by placing it on the floor and moving the running machine over it, or by placing the machine
over the block or attachment and then starting the motor.
Return the floor machine to upright position and adjust handle to operating position.
Recommended handle position is close to the waist with arms extended down. Lock the cam
release lever into position.
NOTE: The hardened steel cam release lever does not require extreme tightening to effectively
hold the handle in position. Over-tightening will shorten the functional life of the lever. To remove
drive block, brush or attachment: Lay the floor machine on it’s back again and disengage clutch
plate slots from driving plate lugs by turning clockwise.
HOW TO OPERATE THE MACHINE
First install the pad driver and pad, brush or other attachments to be
used. Plug the machine in as directed and lower the handle to the
desired operating height and lock in place using the cam lever handle.
Push the safety switch forward and squeeze the switch triggers beneath
the handle grips. This activates the motor and starts the block, brush
or attachment in operation. Each time you release the triggers the
safety switch will reset. You will need to follow the direction above to restart the machine.
CAUTION: When leaving the machine unattended, disconnect the wall plug and return the handle
to the “locked” upright position to prevent accidental starting.

4
TO GUIDE YOUR FLOOR MACHINE
To Right: raise handle slightly. The higher the handle is lifted, the faster the machine will move to
the right. To Left: to change direction, lower the handle until the machine travels to the left. The
more the handle is lowered, the faster the movement to the left.
TRANSPORTING THE MACHINE
Place the handle in the upright position. Lock the handle cam release lever. Tip the machine
back and transport on the wheels.

MAINTENANCE
Once a month remove the motor cover and vacuum out any dust or debris which has
accumulated on the motor. Replace the motor cover by setting it over the holes in the housing
and replace all of the screws. Check and maintain the tightness of all the fasteners.
WARNING: Do not over-tighten the switch housing screws.
Keep the machine clean especially at the handle tube and collar so the handle tube will move
freely through the collar. Inspect the cord for cuts, gashes, or loose prongs; replace as needed.
Disassembly of this motor voids the warranty. Improper disassembly and assembly of this
motor can permanently damage the field or rotor.

TROUBLESHOOTING
Problem Possible Cause

Circuit breaker is not reset. Reset breaker.

Plug is broken or has a loose contact. Replace.
Machine will not start
Circuit breaker is defective or weak. Replace.
Switch is defective. Replace switch.

Over drawn circuit. Unplug anything other than the

Machine will not reach operating speed
machine from the circuit or locate another circuit.

Coupling is broken. Replace. Coupling is not

Motor runs but pad or brush does not covered under warranty. Do not attempt to place
turn a running machine over a block or brush. Always
install and remove the block or brush by hand.

Prevent circuit overload.

Check the pad and change it if it is rough or dirty. Spray buffing or spray cleaning is not a
substitute for scrubbing or mopping a floor. Prepare the floor surface before spray buffing.
Eliminate any extension cord that is smaller than 12/3 wire or greater than 25 feet in length.
Unplug anything other than the machine from the circuit or locate another circuit.

5
6
Ref Part # Qty Description
1 X8911 1 Handle
M8600-3 Handle assembly (includes #1 through #7)
2 X8941 2 Handle grip 1” diameter
3 X8914 1 Thumb switch actuator
4 X8927 1 Label Logo, Metal handle
5 X8923 1 Insulation sheet
6 F5P 1 Momentary Switch 25 Amp
7 X8013 1 Cord hook
8 X8023 1 Circuit Breaker, 15 Amp. C131-7, C171, C201
X8023A 1 Circuit Breaker, 17 Amp. C171HD, C201HD
9 X8266 3 Screw 10-32 x 3/4”
10 X8412-C 1 Label 13” 1HP 175 RPM
X8982 1 Label 17” 1HP 175 RPM
X8983 1 Label 20” 1HP 175 RPM
X8984 1 Label 17” 1-1/2HP 175 RPM
X8985 1 Label 20” 1-1/2HP 175 RPM
X9101 1 Label Dual Speed C202
11 X8965 1 Motor cover
12 X8106 3 Motor Cover Spacer
13 X8265 2 Screw 1/4-20 x 3/4”
14 X8020 2 Washer
15 X8024 2 Wheel, Black, 5” x 1-1/4”
16 X8101 4 Spring Washer
17 X8980 1 Motor 1-1/2 HP 120/240v 60hz C171HD, C201HD
X8981 1 Motor 1 HP 120/240v 60hz C131-7, C171, C201
X8071-TI 1 Motor Assembly 2 Speed C202
18 X8400A 1 Powr-Flite Label
19 X8966 1 Motor Base
20 X1149 1 Brush Cover and Bumper 13”
X8967A 1 Brush Cover and Bumper 17”
X8968A 1 Brush Cover and Bumper20”

7
Ref Part # Qty Description
21 X8212 4 Washer
22 X8218 4 Washer
23 X8219 4 Washer
24 72455A 4 Screw 1/4-20 x 1-3/4”
25 X8977 1 Pivot Pin
26 X9575 1 Axle
27 X8107 2 Handle Spacer
28 X8807L 1 Handle Brace, Left w/ Slot
29 X8807R 1 Handle Brace, Right w/ Hole
30 X8989 1 Cord 14/3 SJTW 51.25” Black
31 X8016 1 Plastic Handle Clamp Knob
32 X1456 1 Handle Lock Clamp
33 X1184 1 Cam Lever Assembly (Includes X8016 and Washers)
NOT ILLUSTRATED
X9049 1 Motor Screen 2 Speed C202
X9050 1 Motor Screen Spring 2 Speed C202
PX7 1 Toggle Switch 2 Speed C202
PX28 1 Toggle Switch Rubber Boot 2 Speed C202
X8530 1 2 Speed Motor Control
X8034-2 1 Rectifier
M1369AS 1 Power Cord Assembly STW 14/3 50’

8
For warranty information go to www.Powr-Flite.com

A Tacony Company
3101 Wichita Court • Fort Worth, TX 76140-1755
1-800-880-2913 • Fax: 1-817-551-0719

X8692 06/2020