Traffic Manual Volume 1 Civil Engineering Department Ministry of Public WorksQatar Traffic Manual INTRODUCTION The Qatar Traffic Manual, together with its companion documents Traffic Control at Roadworks and The Highway Code, has been produced by the Ministry of Public Works, Civil Engineering Department in consultation with the Ministry of the Interior, Traffic Police. The purpose of this Manual is to standardise design in two important areas of traffic management, namely road signing and sign design. The standards contained herein apply to all works to be carried out on the highway and, to ensure that the desired standardisation is achieved, all such schemes must be submitted to the Ministry of Public Works, Traffic Section, for approval The two parts of the Qatar Traffic Manual which form the first volume are:~ Part One, The Traffic Signs Manual, which describes the function and usage of directional signs; regulatory, warning and information signs and road markings. Part Two, The Traffic Design Manual, which considers sign face layout, sign construction and illumination and vehicle crash barriers. The second volume comprises a set of Working Drawings which detail the sign- face layouts for all regulatory, warning and informatory signs. Also included in the second volume is The Traffic Control at Roadworks booklet which sets down the re- quired standards for temporary warning signs and diversion signing for works being carried out on, or adjacent to, the highway. It is also published separately for use by those carrying out the roadworks. The Highway Code forms a completely separate document as its purpose, which is to define good driving practice, is different to that of the Traffic Manual. It is based on the principles contained in the Manual but is presented in a non-technical format for use by the general public. In preparing the Traffic Manual, the Ministry of Public Works has adopted the Vienna Convention ‘European rules concerning road traffic signs and signals’ and United Kingdom highway design practices, as these have been in local use for a number of years. However, it is recognised that their formal adoption and subsequent full implementation will bring about changes in driver behaviour which, together with the continuing development of the country and future technical innovation, will lead to the progressive amendment of this Manual. Consequently, it has been published in loose-leaf form for ease of revision. Users of the Manual who require clarification of certain points are requested to contact the Head of Traffic Section, Civil Engineering Department, Ministry of Public Works, P.O. Box 38, Doha, State of Qatar.CHAPTER ONE — DIRECTIONAL SIGNS Contents Section Title Page No. 1.1 The Highway Network 101 1.2 The Direction Signing System 1.05 1.3. Advance Direction Signs 1.05 1.4 Direction Signs an 1.5 Route Confirmatory Signs 112 1.6 Signs for Special Purposes 113 1.7 Siting of Directional Signs 115 1.00444 143 144 CHAPTER ONE — DIRECTIONAL SIGNS THE HIGHWAY NETWORK Roads within the State of Qatar each full certain functions within the overall network. A hierarchy exists ‘which defines their various roles. Table 1.1 shows the status of road types within the hierarchy and ‘shows how these compare with the three tier traffic signing system. PRIMARY ROUTES These are routes of strategic significance whose purpose is to act as the principal distribution routes between the city of Doha, the main regional centres and the national border. They are generally dual cartiageway roads, built to high geometric standards. ‘The present system of Primary Routes is illustrated in Fig. 1.1 and Fig. 12 ‘SECONDARY ROUTES Secondary Routes serve as area distributors by linking Primary Routes either to each other or by feeding traffic into the Tertiary Route network, They are generally dual carriageway but in rural areas may be single carriageway. ‘The major Secondary Routes are also shown in Fig, 1.1 and Fig. 1.2. ‘TERTIARY ROUTES District distributors, local and access roads are classified as Tertiary Routes. District distributors are urban dual carriageway roads providing high capacity routes between districts. Local roads link access roads to either the Secondary Route network or, in urban areas, the district distributors. Both local and access roads are characteristically low design speed, single carriageway roads. ‘THE ROUTE NUMBERING SYSTEM ‘The Route numbering systam is centred on the city of Doha. As shown in Fig. 1.2, the origin of the Primary Route network is the D-Ring Road, this being designated Route No. 1. The Primary Routes Nos. 1 10 7 extend radially outwards from the O-Ring Road. With the exception of Route No. 59, linking Route No. § to the national border, all Primary Routes have single digit numbers. Secondary and Tertiary Route Numbers follow a branching system based on the Primary Route Numbers. ta road has been allocated a Route Number, that number will appear on all direction signing associated with it. For ease of identification the Route Number is displayed in a rectangle with a yellow background. Where a Route which itselt is not classified leads directly to a numbered Route, the number of that Route may be displayed in brackets on the Advance Direction signs and Direction signs, associated with the unclassified road. This principle is illustrated in Fig. 1.3. Fig. 1.3 Bracketed Route Number To ensure that all new direction signing is consistent with the overall signing policy for Qatar, the details ofall proposed direction signing must be submitted to the Ministry of Public Works for approval 101uopeoyisseia BujuBls uoRoesa pue AemyBIH 11 148. 241 pu speo1 Kewid euoi6ay oy epnout seipos Koy yeu UL “Saino: five| 0 Aepuooes ‘ewe ola 29 UeD asouL 1, URIS YN a UO Babea axe SiopuloD pecs eseuG0 SUL suotyeodsip An pue Suo%ses-s5010 peo! 10) eouepmnd ToT] AIT a @ ape uonpun ieudorde ‘soptuen Ku 04 ord esog ‘ubisop wounned vo stoeudug SeueR, sous seven poubssop pve poreubien Areoeds owas. ie Serpe ammoanuore reuoyeanes 10 sao: KUO Tme20$ 218804 ye Gudeospuey porous uo stseuela SOUR soven seven se suonouy leeds iim SPeoe seinos 00g Bainoy w0ds (on) — Aone) suotount, zero aue2 9048 30000 na ubig vor2enc a a a auerz ous pecs sseooy (éema6eoue (emu) — Aven renp 09 3 mse a caveree —“ouos}auer2 ous spe uk ea BuNnauSIp PEO! ee 2207 — hve aaa ons aueyezionp susp Bung peor ueain Uy apinous wim aver 2 ous yeep uo suin-7 eranop 09 1 speorx’suoHoun, ova ouere2 en ‘Bupued oN ‘satuadoss wos s52008 "Suni oN ‘uoHDUN! p (ong) — Kepuoses owen ‘SmogepunO! LOREeESS ope) viva everezien ——yBno14}J0)peor VERN elewy —_Jonauisia vewn Bamnoy epuaD—S fe) —Ampucoe vain oo ae 40 yo-chs/u0- Suyed on ‘sayedosd woy ssa00e (use1p) — Keuid 19ND ON +n sulog suormun ‘seek olesedos-ope10 10 1 vou siogepunots 9 ‘ausre-zienp ——_10"suNo} Buy peot lew ‘sanou mewn THTHOTEGOD Nouvoulss¥19 ‘vou Nouvalaiss¥19 ONINDIS NOLO Noissa(U)TWESNSD SAVIMBOVIERYD NouoNns ‘avou‘Al-Jumayliyah e ‘Shahaniyah e ‘Al-Kharrarah SAUDA NATHIL Fig. 1.1 Qatar: Primary & Secondary (Rural Distributors) Present System (1987).2 Doha: Primary & Secondary (Urban Distributor) Routes Present System (1987)12 THE DIRECTION SIGNING SYSTEM 1.21 GENERAL DESCRIPTION A direction signing system performs the following functions:~ 1. It must give drivers advance warning of their approach to a junction 2, It should indicate the type of junction that will have to be negotiated, 3. It must inform them cf the destinations that may be reached from each ext. 4, It should indicate the point at which they must turn to reach a destination on a route other than that on which they are travelling 5, It should identify the route and indicate its status within the network, These functions are fulfilled by a colour-coded system of Advance Direction, Direction and Route Confirmatory signs The routes themselves are identified by the colours below:— Primary Routes — Green background, white text and borders Secondary Routes — Blue background, white text and borders Tertiary Routes — White background, black text and borders ‘Advance Direction Signs and Route Confirmatory Signs take the background colour associated with the w route on which they are located, Direction signs fake the colour of the route to which they reer All directional signing in Qatar is bilingual, the destinations and distances being displayed in both Galar ig bilingual Arabic and English. The relationships between this dual tex, the various symbols and the ways in which they apply to each sign type are described in Part Two, Chapter One. 13 ADVANCE DIRECTION SIGNS. ‘Advance Direction Signs are generally provided on all approaches to a junction to indicate the destinations which may be reached from each exit, Each type of Advance Direction Sign fulfils a particular role. By the sign’s form and layout, a driver may determine the type of junction he will encounter, the alternative destinations and, in the case of grade separated interchanges, the distance to the exit. 4.34 ADVANCE DIRECTION SIGNS FOR INTERCHANGES Dus tothe special nature ofthis form of junction two Advance Direction Signs should be provided. The frst, the Far Advance Ditection Sign, is located 1 kilometre from the exit. t should be a ground ‘mounted sign but, where the verge width is limited, @ gantry mounted sign may be used. ADS FADS. ADS FADS ADS FADS aos FADS Lane Specific Interchange ‘AOS FADS w ‘Non Lane Specific Interchange Fig. 1.4 Advance Direction Signs for interchanges: 1.05The second, the Advance Direction Sign, is located 500 metres from the ext. It should be gantry ‘mounted but, at interchanges where the number of lanes on he Through roufe-temains constant, may be ground mounted w : 1.3.1.1 FAR ADVANCE DIRECTION SIGN aoe ¥\ 7 ob Al Muntazah rer Musheirib ps \ ps) tu) ikm w 100 100 ‘Sign 100 is used in advance of interchanges where vehicles leaving the through route reach a secondary junction (usually a roundabout) at which they join their new route. Route numbers should be included, where applicable, bul the ahead destination is not displayed, The distance shown will normally be 1 kilometre but may vary, as described in Section 1.72. Where circumstances di eit may be substituted by igns 102 or 103, as appropriate. 1.3.1.2 FAR ADVANCE DIRECTION SIGN (FREE FLOW INTERCHANGE) ow | EAC) amt PTI) Fig. 1.5 Free Flow Interchange 101 w ‘Sign 101 is 2 variant of sign 100 and is used in advance of a free flow interchange, e.g. a clover leat junction as shown in Fig. 1.5. 1.061.3.1.3 ADVANCE DIRECTION SIGN : NON LANE SPECIFIC INTERCHANGE yoerere)] ORS 102 102 104 Sign 102 is used in advance of interchanges where the numiber of lanes on the through route remains constant, as shown in Fig. 1.6. The angled arrow indicates to the driver that to reach the exit destination he must turn off the main carriageway. Fig. 1.6 Non Lane Specific Interchange This sign displays the ahead and exit destinations with their respective route numbers, where applicable, on separate sign faces, The distance to the exit is displayed on the accompanying Sign 104 pyourarey) ENTE) Ayal! 5S pe City Centre ry ¥\ eu COU) eo 500m 100 100 ested! pile Al Muntazah Musheirib At interchanges where the provision of a sign gantry would be impractical, Sign 102 may be replaced by Sign 100 or 101, as appropriate, When either of these signs is used in this context on Primary and. Secondary Routes, the ahead destination may be displayed alongside the route number. On Tertiary Routes the ahead destination must be displayed, together with the route number (i any) In urban areas the distance to the exit may be omitted 10713.1.4 13.1.5 ADVANCE DIRECTION SIGN : LANE SPECIFIC INTERCHANGE ee ened hve verre) Abu Samrah & Salwa Sl I Immsaeed Fig.1.7 Lane Specific interchange Sign 103 is sed in advance of interchanges where the number of lanes the junction reduces, {as shown in Fig. 1.7. The meaning af a downward pointing arrow, which is positioned over the centre of the lane to which it applies, is that by remaining in that lane the driver may reach the displayed destination, Due to the lane specific nature of this sign type it must NEVER be substituted by a Sign 100 or 101 DISTANCE TO EXIT SIGN rs oo 500m 104 Sign 104 is used in advance of interchanges to indicate the distance to the exit. When used in Conjunction with Sign 102 or 103 it appears as a separate sign mounted to the right of the sign isplaying the exit destination(s). When used in conjunction with Sign 100 or 101 it is incorporated within their signface and has no border, Usually the displayed distance willbe 1 kilometre (Far Advance Direction Sign) or 500 metres (Advance Direction Sign). However, it site conditions prevent a sign being located close to its standard position, the actual distance should be measured (see Section 1.72) and rounded down to the next whole number of hundreds of metres. This latter figure is then displayed, 1.081.3.2 ADVANCE DIRECTION SIGNS FOR AT-GRADE JUNCTIONS ‘At-grade junctions require orly one Advance Direction Sign to be provided on each approach. This w sign will be of the ‘Stack’ or Map” type depending on the configuration of the junction. Each sign displays the destinalion(s) that may be reached from each exit, together with the route number where applicable. As these Advance Direction Signs are located at a maximum of 225 metres {rom the junction (see Section 1.7.2), the distance is not displayed. 132.1 STACK TYPE SIGN ee NGO Cu So * Reet CCU) Pea mee 0 be 4 Perea ea o. Neo w 105 105 1 Aubroe pl opie |, Mantazah Umm Ghuwailina juntazal 0 gure! 4 Al Mansoura Najma 105 105 ow ‘Sign 105 is used in advance of simple priotty or signal controlled junctions. The arrows indicate the directions that must be take to reach the various destinations. The lett and right direction arrows are Usually horizontal but may be inclined at 45 degrees to indicate a free flow manoeuwte at the junction, as shown in Fig. 1.8 =m { a Zi ss ——————s ww Fig. 1.8 Free Flow Right Turn 1.0913.22 MAP TYPE SIGN ‘A map type Advance Direction Sign is used in advance of an al-grade roundabou! or complex priority junction, The map symbol is an idealised plan of the junction and shows the exits in, as near as Possible, the correct orientation with respect to the approach on which the sign is situated Spee Bin Mahmoud Pr a er Peas) Peles ]) cova ee. BAB At Rayyan Industriat Chi nee Area id aI Al Corniche 106 106 ‘Sign 106 is used in advance of roundabout junctions. ee + Were AtSeta [RJ Sauda Nathil ~~ Eee aaa Diary ars A Err 0 107 Sign 107 is used in advance of any priority junction where the driver's route to his chosen exit is not immediately apparent, The map symbol illustrates to the driver the configuration of the junetion with respect to his approach, as demonstrated by the example shown above.14 DIRECTION SIGNS Direction signs should be provided at a junction to show the destination(s) that may be reached from each exit, together with route number where applicable, Ld 1.41 DIRECTION SIGNS FOR INTERCHANGES 1.41.1 NON LANE SPECIFIC INTERCHANGES. eu 102 102 Sign 102 is used at interchanges where the number of lanes on the through route remains constant. At ww interchanges where itis impractical to provide a gantry, these signs may be substituted by a Sign 108 which will display the destination(s) and route number, it any, for the exit only. 1.4.1.2 LANE SPECIFIC INTERCHANGES. Eyer) seal CUE Wee etal aked nue it) 103, 103 Sign 103 is used a interchanges where the number of lanes on the through route decreases. Due to the lane specific nature of the interchange, these signs may NEVER be substituted by Sign 108,1.42 DIRECTION SIGN FOR AT-GRADE JUNCTIONS 1421 FLAG TYPE SIGN Pry ety) Al Gharafa 108 Sign 108 is provided al each exit trom an at-grade junction, irrespective of type. w 15 ROUTE CONFIRMATORY SIGN 04 ee od Pn Fe evra) Sauda Nathil 45 km Al Sela 160 km 109 ‘Sign 109 is used on Primary and Secondary Routes and on the exits from all major junctions on these Routes. It should display the same destination(s) for its Route as shown on the previous Advance Direction Sign and the associated distances) should be quoted to the nearest kilometre. Route Confirmatory Signs may also be provided along a Route, in which case they should be located so thal they are spaced no more than 10 kilometres apart w 1.1216 SIGNS FOR SPECIAL PURPOSES 4.61 MILITARY SIGNS d Pre! => pisagl Army Camp Army Camp 105M 108M Signs 105M and 108M are used to direct drivers to military installations. Their format and use is the ‘same as for Signs 105 and 108, but their red borders and arrows are peculiar to military installations, The signs may include the name of the installation. 1.62 RECREATIONAL SIGNS Olonod! dita to Doha Zoo 105A 108R Signs 105R and 108A are ssed to direct drivers to recreational areas such as 200s, museums, historical buildings, monuments, otc. The green text and border indicate that these signs are not part of the main direction signing system. In respect of format, use and positioning the conditions of paragraph 1.6.1 apply. 1.63 TEMPORARY DIRECTIONAL SIGNS Alege pl dil gt pl Umm Ghuwailina Umm Ghuwailina 10st 108T Signs 105T and 108T are used as deemed necessary for major diversions. The black text is displayed on a yellow background, in common with the standard diversion signing illustrated in Section 3.14 1.181.6.4 SITING OF SIGNS FOR SPECIAL PURPOSES ww These signs must meet the same siting requirements as those for the standard directional signs (see Section 17), Where this would result in standard and special purpose signs occupying the same site, both signs should be mounted on the same posts, as shown in Fig. 19. er Vac Pre) Al Gharafa Army Camp Fig. 19 165 ROUTE REFERENCE MARKER Retlector w Plastic See : Demarcation \ <— Route n ve Post ) + Direction (A or B) > e THE | =— Kilometre Point 10 Relerence Marker 110 Fig. 1.10 This sign is to be provided on all numbered Routes 10 form the Route Referencing System. The information contained on the sigh is intended for use by the Ministry of Public Works and the Trafic Police for their various purposes and therefore the sign should be installed in such a fashion so as not to distract other drivers itis to be mounted on demarcation posts as shown on Fig. 1.10. A17 SITING OF DIRECTIONAL SIGNS 17.1 GENERAL w This section considers those aspects of design that may be described as ‘site dependent’ ~ — Siting of signs in relation to the junction — Minimum Clear Visibility Distance — the distance over which a driver's view of the sign is unobstructed. Before any of the above may be determined, an assessment must be made of the 85th percentile vehicle speed in advance of -he position where a sign is required. The actual position at which this value is assessed will depend on the physical characteristics of the site, e.g. horizontal and vertical alignment, frequency of minor junctions, ete, but generally should be between 200 and 400 metres in advance of the likely sign position, Ss 4.7.2 ADVANCE DIRECTION SIGNS 1.724 JUNCTION REFERENCE POINT {Ihe distance in advance of a junction at which an Advance Direction Sign should be sited is measured w from a ‘junction reference point’. This reference point is defined as follows (i) interchanges — the point at which the carriageway widens to form the exit road (Fig. 1.11) Junction Reference Point 4 Fig, 1.11 Locations of Junction Reference Point for interchanges (i) At-grade junctions — the STOP or Give Way line, or — the point at which the carriageway first widens to develop additional turning lanes or slip roads (Fig, 1.12). Junction Reference . Point Fig. 1.12 Locations of Junction Reference Point for At-Grade Junctions. 1951.72.2 ADVANCE DIRECTION SIGNS FOR INTERCHANGES ‘The standard distances at which the Far Advance Direction Sign and the Advance Direction Sign would be sited are shown in Fig. 1.13. ww 1 km. 500m ‘ADS FADS Fig. 1.13 Locations of Advance Direction Signs for interchanges Where site conditions are such that a sign cannot be positioned al its standard distance, it should be relocated further from the junction reference point. Where this is not possible, due to the proximity of junctions, the sign should be located as close to its standard position as practicable. The way in which the distance to the exit should be displayed under these circumstances is described in Section 1.3.15. The Minimum Clear Visibility Distance requirement is given in Table 1.2 1.723 ADVANCE DIRECTION SIGNS FOR AT-GRADE JUNCTIONS ‘The distance in advance of the junction reference point at which the Advance Direction Sign should be sited is related to the 85th percentile speed of vehicles on that approach, [ADVANGE DIRECTION SIGNS | _DIRECTIONSIGNS _| ROUTE CONFIRMATORY SIGNS| ‘5th Percent. Distance trom Minimum Clear Minimum Clear Speed Reterence Point ‘Visity ‘Wate 2) Distance keh 0.45 % «6 0 50 4860 100 60.100 5 % e020 125 100-160 100 100 over 80 150 150-225 125 125 Table 1.2 Visibility and Siting Distances for Post Mounted Signs Note +: Slender obstructions such as trafic signa poles and lamp columns may be ignored [Note 2 This column is net applicable to Advance Direction Signs for Interchenges. 17.3 DIRECTION SIGNS Direction signs are located at the junction itself. The actual siting of such a sign is a matter for individual judgement, but it must be borne in mind that it should be sited so that: (i) it is visible to drivers both during their approach and whilst making any necessary turning movement (Table 1.2) (il) there is no confusion as to which exit the sign refers. Wherever possible the signs should be sited immediately beyond the point at which the turning manoeuvre must be made as illustrated in Figs. 1.14 to 1.18, 1.16Preferred ® ——-—-\|-k}---—- alternative Permitted alternative —®Q —— —— — 77 7 A where ground mounted FADS and ADS are used Fig. 1.14 Location of Direction Signs at a Non Lane Specific Interchange Gantry located where SO ful lane width achieved tA] [BA] AaB] [C4] Fig. 1.18 Location of Direction Signs at a Non Lene Specific Free Flow Interchange -®--——-—-—-H Se A B si Fig, 1.16 Location of Direction Signs at a Lane Specific Interchangec Fig. 1.17 Location of Direction Signs at a Roundabout 4.74 ROUTE CONFIRMATORY SIGNS These signs should be sited approximately 200 metres beyond the last point at which a vehicle could join the main carriageway alter nagotiating the junction, e.g., the end of an acceleration lane. They may also be provided between junctions on major routes, such that their spacing is not greater than 10 kilometres. 118CHAPTER TWO — REGULATORY SIGNS Contents Section Tile 24 General 2.2 Mandatory Signs 23 Prohibitory Signs 2.4 Police and Customs Signs 2.5 Distance Plate Page No, 201 202 2.08 214 214 20024 244 213 244 248 CHAPTER TWO — REGULATORY SIGNS GENERAL Regulatory signs are the means by which the Traffic Laws are put into effect. Consequently those drivers who disobey the signs are breaking the Law. Signs in this category fall into the following classifications: Mandatory Signs — which give instructions to drivers as to what they must do. The STOP and Give Way signs are examples which, because of their significance, are given special symbolic shapes to highlight their presence. Other mandatory signs, such as the Keep Right sign, are circular with white symbols on a blue background. Prohibitory Signs — which give instructions to drivers as to what they must not do. The signs are circular with a red border and generally have a red diagonal bar. The message of certain regulatory signs must be amplified by the addition of a supplementary plate. ‘The size of text to be used on the plate is given in Table 2.1 ‘The majority of regulatory signs are available in four sizes, the size and required visibility distance being dependant on the 85th percentile speed of traffic using the road on which they are located. The required dimensions are laid down in Table 2.1 Regulatory signs are positioned al the point at which the instruction or restriction applies. ‘6th Height of Minimum ‘Supplementary percentile Triangular Clear Plate Text speed or Circular Visibility sign Distance Aleph-height (Note 1) (Note 3) (xheight) kph mm metres mm 0-45 600 60 85 45-60 750 (60) 60-80 900 75 130 (75) Over 80 1200 100 170 (100) Note 1: The STOP ana Give Way gn wil be one s2e larger than shown here. (A 1500mm size sign must be sed when the 85th percentile spaod isn excess of 80 kph) NNote2: leph-height and x-height are defined in Part Two, Chapter One. Note: Slender obstructions suc as tafe signal poles and lamp columns may be ignored Table 2.1 Sizing and siting of Regulatory Signs 20122 MANDATORY SIGNS 221 THE STOP SIGN Sign 200 requires that all vehicles stop at the w transverse road Marking 500, No vehicie may then enter the major road it the manoeuvre would cause major road trafic to alter ils speed or drecion to avoid a colision. STOP signs should only be stalled 2 junations where the wsiaity criteria, specited n Table 22, cannot be met They should be positioned between 1 and 9 moties in advance of the road y marking 900, a5 shown In Fig. 22 ww Fig 2.1 Visibility Splays 85th percentile speed S S ‘on major road kph m m wo 0-45 50 50 45-60 75 78 60-80 120 100 Over 80 175 100 Table 2.2 Visibility distances below which STOP signs must be provided —s: ; 600 So w Fig. 2.2 Siting of STOP and Give Way Signs 2.02Where the minor road is a one-way street with two or more lanes or a two-way street with a central island at the junction, an additional STOP sign should be positioned on the off-side footway or central island, as appropriate. 2.22 @ 223 2.2.4 ROADWORKS 201 THE GIVE WAY SIGN 203 MINI ROUNDABOUT SIGN 204 Signs 201 and 202 are manually operated temporary signs used to control trafic at road works. where cartiageway width has been reduced sufficiently that only alternate one-way (‘shuttle’) movement of traffic is possible. The signs are mounted back-to-back and indicate to traffic when it may or may not proceed through the area under control. The 750mm size of sign is the minimum size used. Sign 203 requires that drivers give way to other vehicles at the junction ahead, itis used at (i) prionty junctions where visibility distances are ‘equal to or greater than those specified in Table 2.1. It is then accompanied by road Markings ‘501 and 503 (ii) roundabouts, in which case road markings 602 ‘and 503 are used. The sign is sited between 1 and 3 metres in advance of the road marking and an additional sign should be provided on the central median or traffic island, where either of these is present, or on the offside footway where the minor road is a one-way street. Sign 204 is used to supplement Sign 203 at mini roundabouts. 203225 226 227 TURN RIGHT (LEFT) SIDE ROAD 208 ROAD DIVERGES, 209 Sign 205 is used at junctions where all traffic must turn right. The symbol may be reversed, Plates 206 or 207 may be used to supplement Sign 205 where traffic must turn right on joining @ dual carriageway or one-way sireet respectively Sign 208 is used on the nose of traffic islands within junctions where trafic may proceed ahead or to the right only. The symbol may be reversed ‘Sign 209 is used at roundabouts on the median strip oF trafic island at each exit in the position shown in Fig. 23 to indicate the point of divergence between the circulatory carriageway and exit 2.3 Siting of Sign 209 Where a Direction Sign 108 is provided at this location, Sign 209 need not be used 2.042.2.8 TURN RIGHT (LEFT) AHEAD . 210 229 KEEP RIGHT (LEFT) ww an 2240 PASS EITHER SIDE 212 22.11 ONE WAY STREET 213 ‘Sign 210 is used on approach to a junction at which all traffic will be required to turn right. It will normally only be provided where the alignment of the approach is such that the layout of the junction is not readily apparent. The sign should be located approximately 50 metres in advance of the junction, but this may be reduced if another junction occurs within that length. ‘The symbol may be reversed Sign 211 is used to indicate an obstruction in the carriageway that requires the motorist to pass to the right. It should be positioned as near as possible to the leading edge of the obstruction. ‘Typically, this applies to traffic islands or refuges on two-way roads or the beginning of the median strip where a single carriageway widens to become dual cartiageway. ‘The symbol may be reversed. Sign 212 is used 10 indicate an obstruction, such as a traffic island in a one-way street, where the same destination may be reached by passing either side of the obstruction. Sign 213 is erected on ether side of the carriageway at the point of entry to a one-way street. In order 10 avoid contusion as to which street the sign refers, it may be set back into the mouth of the road. Repeater signs should be provided along the length of the street, on alternate sides, with a spacing between successive signs of not more than 50 metres, If another road intersects and enables traffic to enter the one-way street an additional sign should be provided immediately downstream of the junction. 2.052212 SPEED LIMIT ~ 24 . SS 22.13 MINIMUM SPEED de pu yial Minimum speed w a7 minimum speed w 218 Sign 214 is used to indicate the speed limit in kilometres per hour for the road on which the sign is located. The sign is positioned on both sides of the carriageway at each point where the speed limit changes. On long routes, eg. those over five kilometres, repeater signs may be provided but their size should be reduced from that of the prime sign, as detailed in Table 2.3. Prime Sign Repeater Sign Diameter (mm) | Diameter (mm) 600 450 750 600 900 750 1200 00 Table 2.3 Sizes of Speed Limit Signs ‘Sign 215 is used to indicate a minimum speed limit. It is installed at each point where trafic becomes subject to the speed limit displayed and may be repeated over the length of the restriction. The repeater sign should be smaller than the prime sign, as detailed in Table 2.3, Plate 216 is used to supplement Sign 215 al each point where traffic becomes subject to the minimum speed limit, Sign 217, together with supplementary Plate 218, is erected at the point where the restriction ends. These signs are provided on both sides of the carriageway. 2.062.2.14 — LORRIES ONLY ww Plate 219 is used to supplement Signs 215 and 217, when the restricion applies only to heavy goods vehicles 219 22.15 PRIORITY OF PASSAGE ‘Sign 220 signifies that vehicles passing the sign have prioriy over oncoming trafic ww ‘Sign 221 signifies that oncoming trafic has priory These signs are used at locations where the carriageway width is restricted and indicate which stteam of trafic has priorty when negotiating the restrictions They may only be used where the far ends of the restricted length are mutually visible and where vehicle speeds are not likely to be high Both signs are repeated at the end ofthe restriction in on combination with supplementary Plate 346 (End). w Fig. 24 illustrates a recommended layout for these signs rnin FSS . vil La c ww Fig. 2.4 Layout of Priority of Passage Signs End 2.0723 PROHIBITORY SIGNS 231 PROHIBITION OF TURNING w sah ® © 222 223 w 224 232 PROHIBITION OF ENTRY SIGNS 4 2321 NO ENTRY i Except buses Signs 222, 223 and 224 are used at junctions to prohibit lef, right and U-turn movements. Signs 222 and 223 should be sited on the left and right-hand side of the carriageway, respectively. Sign 224 should be sited on the median strip of a dual carriageway. At trafic signal-controlled junctions, the sign should bbe attached to the primary signal pole on the appro- priate side of the road, so as to be clearly visible but ‘not obscure the signal These signs will normally be provided on both sides of the road at every point of entry to the road to which the restriction applies Care must be taken to ensure that the signs are positioned such that no contusion shall arise as to which road the signs apply. To this end the signs may bbe set back slightly into the mouth of the junction and/or angled towards the direction of approaching traffic The signs must be clearly visible at all times, Sign 225 prohibits entry to a road by all vehicles unless used in combination with exempting supplementary plate 226. Plate 226 is used to supplement Sign 225 to exempt certain categories of vehicles from the restriction imposed by the ‘No Entry’ sign. The permitted legends are Except buses Except buses and taxis. Except for access, 2.082322 — NO MOTOR VEHICLES . a 2323 NO BUSES 2324 NO LORRIES - @ 29 to \ 10T 230 Vier Aes 8.30-16.00 Sign 227 prohibits entry by any motorized vehicle. Sign 228 prohibits entry by any vehicles designed to carry more than 12 passengers. Sign 229 prohibits entry by any goods vehicle. Plate 230 is used to supplement Sign 229 where the Prohibition applies to vehicles whose gross weight exceeds thal displayed. Plate 231 is used to supplement Sign 229 where the Prohibition applies during certain hours only. 2092325 _ 2326 w 2327 23.28 w ‘AXLE LOAD LIMIT ® 232 WEIGHT LIMIT © HEIGHT LIMIT © LENGTH LIMIT <0 ‘65m ‘Sign 232 prohibits entry by any vehicle on which the loading of any axle exceeds the figure shown on supplementary plate 230. Sign 233 prohibits entry by any vehicle whose gross weight exceeds that indicated. It may be used to Prevent access to a road or area or to protect individual structures such as bridges. Sign 234 prohibits entry by a vehicle exceeding the indicated height. It should be noted thal, where clearance is limited, it is usual 10 use Sign 337 (Maximum Height Warning), rather than impose a vehicle height restriction. Sign 234 must NOT be used as a warning sign ‘The height indicated on the sign face should be at least 100mm less than measured minimum clearance fon the road to be regulated, The height is then ‘expressed as the next lowest multiple of 100mm. Sign 235 prohibits entry by any vehicle exceeding the staled length. The length should be expressed in multiples of 100mm. 2102329 WIDTH LIMIT 4 206 29210 EXCLUSION FROM LANES w 237 29211 ALTERNATIVE ROUTES w 233 GENERAL PROHIBITORY SIGNS 2331 NO PEDAL CYCLES ww 238 Sign 236 prohibits entry by any vehicle exceeding the stated width. The stated width should be less than the minimum clear width of the road in question by at least 200mm and should be quoted to the next lowest multiple of 100mm Sign 237 prohibits certain vehicles from using Particular lanes. The legend indicates the number of lanes of the carriageway, the class of prohibited vehicles and the lanes from which they are excluded, The prohibitory symbol may be any of the Signs 229, 232, 233, 234, 295 and 236. Where Signs 229, 232, 233, 234, 235 or 296 are used. an alternative route must be provided. In certain cases it may also be necessary to provide directional signing in advance of, and along the alternative route, The following signs will normally be provided on the nnearside of the road at every point of entry to the road to which the restriction applies. Sign 238 prohibits the riding of pedal cycles on a road or within a defined area,2332 w 2333 w 2834 2335 4 ww NO ANIMALS 239 NO PEDESTRIANS PEDAL CYCLES ONLY 2a NO OVERTAKING Sign 239 prohibits animals being herded on the highway and may also be used to ban animal-drawn vehicles from using a particular road, Sign 240 prohibits pedestrians from entering a road or defined area Sign 241 instructs that cyclists must proceed by the indicated route and prohibits the use of the marked route by any other type of vehicle. Sign 242 is used to prohibit overtaking, where Necessary, on roads where this cannot be accomplished by the use of road Markings 509 or 510 (the Double Line System). At the beginning of the restriction itis supplemented by Plate 243 and at the end of the restriction by Plate 346 (End) Where the restriction extends over a long distance Sign 242 may be repeated, subject to it being reduced in size as detailed in Table 23. Sign 244 prohibits overtaking where necessary by goods vehicles only. As with Sign 242, itis used with supplementary Plate 346 (End) at the end of the restriction 2122336 NO SOUNDING OF HORNS ww Sign 245 prohibits the sounding of horns. 245, 23.37 NO WAITING Sign 246, together with supplementary Plate 247, is used al locations where the parking of vehicies is prohibited, These signs must be provided atthe end points of the restchon, with Plate 247 clplaying a Single arrow to Indicate the direction in which the restriction applies, Where the resticton extends for a Gistance greater than 50 mettes, the signs must be repeated at intervals of not more than 28 metres. On - the intermediate signs, Plate 247 must include a double arrow. oe Where parking is prohibited only during certain hours of the day, the time that the restriction is in force is displayed on Plate 247 and the signs are used in asda! Eee conjunction with road marking 828 Where ge parking is prohibited at all times, plate 247 displays Vier AF ‘No Parking’ only and the signs are used in No Parking conjunction with road marking 527, 8.30 - 16.00 <= > These signs are mounted parallel to the ker i. hese signs are mounted par rb, The text on Plate 247 has an aleph-height of 65mm («height 87.5mm), 23.38 NO STOPPING (CLEARWAY) A Sign 248 prohibits drivers stopping their vehicles unless in an emergency or directed by the Traffic Police. Its provided at the commencement of the Clearway, where it is supplemented by Plate 248, and repeated 248 at intervals not greater than 700 metres until the termination of the Clearway, where itis supplemented : : by Plate 946 (End), The repeater signs are smaller todo! Esiee than the prime signs, as detailed in Table 23 Saad These signs are installed on both sides of the No Stopping carriageway 24 ~ . 21324 POLICE AND CUSTOMS SIGNS 241 POLICE . cote Sa) 250 242 POLICE VEHICLES SRST pene ger) Pan cue 251 243 CUSTOMS. 25 DISTANCE PLATE Sign 250 may be used by a Traflic Police Officer 10 indicate that temporary restriclions are in operation over a short length of carriageway, eat the scene of an accident The permitted legends are: Police — accident Police — slow Police — tire They may be used in conjunction with the temporary warning Sign 338, Sign 251 restricts access at particular locations 10 police vehicles only. It may be used in both permanent and temporary situations. Sign 252 is used at Customs Houses or border stations {0 indicate that all drivers must stop and report to the appropriate official Sign 253 may be used to supplement the prohibitary signs described in Section 23 where no other method can be found to provide an advance warning of the prohibition or restriction. it should be noted that such ‘a warning is usually provided by (0) use of the appropriate triangular warning sign (Chapter Three), or (ii) incorporating the prohibition sign on the Girectional signing, to show the route on which the prohibition exists, This sign may also be used to supplement certain warning signs (Chapter Three) and is used in advance of roadworks (see ‘Traffic Control at Roadworks’ published by the Ministry of Public Works) 214CHAPTER THREE — WARNING SIGNS Contents Section Title Page No. 34 General 301 32 Priority Junctions 3002 33 Roundabouts 3.03 34 Merging Traftic 3.04 35 Bends in the Road 3.04 36 Road Narrows 3.08 37 End of Dual Carriageway 307 3.8 End of One-Way Working 307 39 Traffic Signal Operation 3.08 3.10 Pedestrians and Children 308 3.11 Animals 3.09 3.12 Other Hazards 3.09 3.13 Temporary Warning Signs 312 3.14 Warning Signs at Roadworks 9.13 Appendix A Supplementary Plate Messages 3.16 3.0034 was - » ~ CHAPTER THREE — WARNING SIGNS GENERAL Warning signs are used to alert drivers to potential hazards on the road ahead, Most of these signs are triangular having a red border surrounding a black symbol on a white background. The symbols give a pictorial indication of the likely hazard, In certain cases supplementary plates may be added to provide ‘extra information, ‘The signs are available in five sizes. The appropriate size, Siting Distance and Minimum Clear Visibility Distance together with the required size of text for the supplementary plates are specified in Table 3.1 asth Height Distance Minimum Supplementary Percen- of of Sign Clear Plate tile Warning from Visibility Text Speed Triangle Hazard (Note 2) Aleph-hoight (x-height) kph mm m m mm 0-45 600 40-50 60 8 (60) 45 - 60 750 50-100 60 85 (600) (60) 60-80 00 100 - 200 75 130 (750) (75) Over 80 (1500) 200 - 300 100 170 1200 (100) (909) Note 1: Alephsneight and x-height are defined in Part Two, Chapter One. Note 2: Slender objects such as tratic signal pole nc amp columns may be ignored ‘Table 3.1 Warning Signs, Sizes, Siting and Visibility Distances ‘The smaller alternative sizes shown in brackets should only be used where amenity considerations or physical restrictions apply. Reference must be made to the Ministry of Public Works prior to the Specilication of a 150mm sign, as its use implies that certain other measures, e.g. to reduce vehicle speed, may be required, 3013.2 PRIORITY JUNCTIONS 324 CONTROL AHEAD ww Sign 300 is used to warn of a junction ahead controlled either by Sign 200 (STOP) or Sign 203, (Give Way), Gerla ql it may only be used in conjunetion with supplementary eo Plate 301 or 302. ee’ 4811 Give way © [stor 100m 50 m 322 SIDE ROAD(S) AHEAD Signs 303 to 307 warn drivers on a major road of @ junction ahead and indicate both The TayouT of the junction and the priority route through it. The signs appear only an the priority route (indicated by the wider route symbol) and may only be provided when all of the following conditions apply w 303 304 () There are no map type Advance Direction Signs. (ii) The junction is not controlled by trafic signals, 7 (ii) There are no STOP or Give Way signs and/or cartiageway markings on the priority route. (iv) Carriageway markings cannot adequately ‘convey the information to the driver. Signs 304, 305 and 307 may have their symbols 305 306 reversed where necessary Sign 205 may only be used where the distance between the junction is less than that given in Table 82. Otherwise two Signs 304 should be used. Sign 306 is used to war of the exit from a U-turn on roads where the 85th percentile speed is greater than 60 kph. In urban areas, it may be used to wam of the w exit from a one-way street. 307 3.02Where the distance between two successive junctions is such thatthe siting requirement of Table 3.1 cannot be mel, the sign warning of the second junction should be installed immediately beyond the first, so that the Minimum Clear Visibility Distance is achieved, Where a junction warning has to be placed further in advance of the junction than recommended, it may be supplemented by Plate 253 (Distance). ssth Distance Percentile between Speed junctions kph metres 0-45 60 45-60 100 60-80 200 Over 80 300 ‘Table 3.2 Junction spacing requirement for Sign 305 Sign 308 may be used as 2 supplementary plate to junction warning signs on high speed roads, as directed by the Ministry of Public Works. Eee peers Greist 308 33 ROUNDABOUTS Sign 209 is used together with countdown marker Plates 414 to 416, (refer 10 Section 42111) to warn rivers of their approach to a roundabout. The signs are located on both sides of the carriageway at 300m, 200m and 100m in advance ot road Marking 802 (Give Way) 3.0334 MERGING TRAFFIC w 310 an 35 BENDS IN THE ROAD 35.4 SINGLE BEND ww 312 wo 352 DOUBLE BEND 313 w Signs 310 and 311 are used in advance of junctions where two streams of traffic, travelling in the same Girection and of equal priority, merge, e.g. at a slip road joining a main carriageway. They may NOT be used where one of the joining streams has priority over the over. Sign 310 is located on the road joining from the left Sign 311 is located on the road joining from the right. Both signs are provided on each side of the carriageway. Sign 312 is used to give advance warning of a severe bend. Where the bend is to the right, the symbol is reversed. It is not possible to define exactly the conditions under which this sign should be used, as the degree of hazard that a bend presents depends on a number of variables. However, on dual carriageway roads where the 85th percentile speed exceeds 80 kph, Sign 312 should be provided in advance of any bend of radius less than 400 metres. The sign should be installed on both sides of the carriageway. Elsewhere each site must be individually assessed in terms of bend radius, approach speed, visibility, carriageway superelevation and surface skid resistance — and the sign provided only where it is concluded that the driver would find difficulty in Negotiating the bend without significantly reducing his speed Sign 313 should be used where two or more bends of similar severity follow in close succession, ie. within the distance shown in Table 33. The direction of the bend symbol is reversed when the first bend is to the right. 85th Distance Percentile x Speed (see Fig. 32) kph metres Below 80 200 Over 80 300 Table 3.3 Double Bend Spacing Distances 3.04Bend 2 ww x Bend 1 Fig. 3.1 Distance between Double Bonds 353 CHEVRON SIGN w a4 . w ‘Supplementary Plate 340 (Extent of Hazard) should be Used if a series of bends occurs such that it is not possible to provide signs at the distances given in Table 3.1. It is not then necessary to individually sign ‘each bend. Sign 314 is used in the following situations (i) at a sharp bend in the road where Sign 312 would Rot adequately convey to the MOTonsT Ne severity of the bend. In this case Signs) 314 SHOUT Be posilioned as shown in Fig. 92, with the centre ine ofthe sign aligned withthe centre line of the lane or carriageway of the oncoming vate Hf the angle of the bend exceeds 90 ‘one sign may be used. more than (i) a roundabouts Sign 314 should be mounted on the central island opposite each approach as shown in Fig. 33. Hf @ roundabout apoproach has 3 or more lanes the sign width should be increased to incorporate 4 (or more) chevrons. The permissible sign sizes are detailed in Table 34 asth | Height | Minimum | Module Percentile | of | Length | Extension Speed | Sign Below80 | 400 | 1200 600 Overs0 | 800 | 2400 1200 Table 3.4 Permissible Chevron Sizes 3.05Fig. 32 Fig. 3.3 36 ROAD NARROWS, Signs 315 and 316 are used to warn of reduction in carriageway width where the taper is more severe w than the values given in Table 35. Sign 315 is used where the reduction occurs on the offside or, when the symbol is reversed, the nearside. Sign 316 is used where the reduction occurs on both sides. They may be supplemented by Sign 356 (Single File Traffic), typically at roadworks. Speed limit Taper kph 0-45 1 in.40 ss be 45-60 1in'50 60-80 1in75 Over 80 tin 110 - Table 3.5 End of Dual Carrlageway Taper ww 9.0637 317 A 318 A END OF DUAL CARRIAGEWAY "AN AN Signs 317 and 318 are used to warm of the approaching transition from dual carriageway to single carriageway, two-way operation. The siting of these signs relative to the end of the dual carriageway is shown in Fig, 3.4, Additional Sign 40-300 required i 83h _ SeeTane'31 —"[— percentile pees 7 over 80 kph 3 Sign 317 al end of median sttip, Fig. 3.4 End of Dual Carriageway w q —=.WG 38 END OF ONE-WAY WORKING ww ww Sign 319 should be used on a one-way carriageway to warn of the approach to a T-junetion, with two-way traffic on the major road, 3073.9 TRAFFIC SIGNAL OPERATION 394 ww ‘TRAFFIC SIGNALS AHEAD 320 39.2 TRAFFIC SIGNALS NON-OPERATIONAL 321 tw «—-310_—“ PEDESTRIANS AND CHILDREN 3.10.1 PEDESTRIAN CROSSING 322 Sign 320 should be used 1o warn drivers of their approach to any traffic_signal control whether permanent or temporary, when: either (i) the installation is remote trom similar installations or (i) the clear visibility distance to the primary signal ahead is less than 60 metres. (On high speed roads a repeater sign should be supplemented by Plate 253 (Distance). This is normally located at twice the recommended distance from the junction (see Table 3.1), Sign 321 is used to warn drivers that the tratfic signals they are approaching are temporarily out of service. The sign must be removed as soon as the signals become fully operational Sign 322 should be used to warn of the presence of an uncontrolled pedestrian crossing facility and should be erected on both sides of the carriageway (on the approaches to the crossing. On roads where the 85th percentile speed is less than 45 k.p., it should only be used where visibility of the crossing is impaired 3.089.10.2 CHILDREN As dn phe lito sU ale School Playground 324 325 3.11 ANIMALS A tw «312, OTHER HAZARDS 3121 SLIPPERY SURFACE A 327 5 dere Slippery road 328 Sign 323, used in conjunction with supplementary Plates 324 or 325, warns drivers of the proximity of a school of playground and should be erected on both sides of the carriageway on the approaches to the hazard. Sign 326 should be used at locations where it is possible that animals may be present on the road The symbol may be changed to show a sheep or goal as appropriate, Sign 327, together with supplementary Plate 328, should be used where there is a greater risk of skidding than normal. It is intended that this sign should be used as a short-term measure and only until remedial treatment has been completed 3.093.122 DRIFTING SAND ww 320 4S pie Jle, Drifting Sand 300 — = 3.123 LOW FLYING AIRCRAFT 331 wy 3.124 ROAD HUMPS 332 cele Lolo! ‘Speed humps 333 334 ‘Sign 329, together with supplementary Plate 930, should be used to wam drivers of the possibility of drifing sand on the carriageway. Sign 331 may be used on roads where low flying aircraft or sudden aircraft noise may distract drivers, Sign 332 is used to warn of a single road hump or series of road humps installed on the road to act as a speed control device. It should be supplemented by Plate $33 at the beginning of a residential area or road having several road humps. Plate 334 may be used 10 supplement Sign 332 to indicate the recommended maximum speed at which drivers should negotiate the hump(s). 3.103.425 3126 3127 UNEVEN SURFACE 335 att Girl sooo Uneven surface MAXIMUM HEIGHT 337 OVERHEAD CABLES 338 Sign 335, together with supplementary Plate 336, is used to warn drivers of a potential hazard due to cartiageway surface irregularities which might impair vehicle control. This sign should be removed as soon ‘as remedial action has been taken. This sign must NOT be used instead of Sign 332 Sign 397 is used to indicate the maximum height of vehicle that may pass underneath a structure spanning the carriageway, where the clearance of that structure is less than 55 metres, The sign is located in advance of the structure, as specitied in Table 3.1, but may also be mounted on the structure itselt to ‘emphasise the warning. The figure quoted on the sign must be at least 100mm less than the measured minimum clearance, to allow a margin for driver erro, and should be expressed to the next lowest multiple of 100mm, Wherever possible an alternative route for vehicles exceeding the stated height should be indicated in advance of the junction prior to the structure. Sign 338, together with supplementary Plate 339, is used to warn of a overhead electricity supply cable and specifies the maximum height of vehicle that may safely pass underneath. Its important that warning be ‘ven, particularly of high voltage cables, even where the height of the cable enables high vehicles to pass. To further emphasise the warning, height gauges may be installed on the approaches to the cable crossing point ant(eda Lai YI ww eo Maximum height 5m 339 3.12.8 EXTENT OF HAZARD pS 0 atl Plate 340 may be used to supplement a warning sign where the hazard to which any of the foregoing signs For 2km refers extends over a distance rather than being confined to one location 4 A 3.129 PAVED ROAD ENDS seed be le! dalyo Eero) Sign 341 is used 10 warn motorists that they are a approaching the end of paved carriageway. 3a ww 3.13 TEMPORARY WARNING SIGNS 3.131 HAZARD WARNINGS Sign 342 is intended for use in situations where a symbolic sign would not be appropriate. I is usually supplemented by Plate 343, a2 w 312i dale lel ‘Surveying 3.43.2 HIGHWAY CHANGES. ery) [lel oe | ACRE hs Ov oe 3.14 WARNING SIGNS AT ROADWORKS w Plate 243 gives a written warning of the nature of @ hazard. The permitted legends are: Census Flood Road Ends Surveying Smoke Sign 344 should be used to warm motorisis of ‘changes that have taken place at locations with which they are familiar. The requirements for size of lettering, siting, visibility etc., are as those set out in Table 3.1 for triangular warning signs. The sign is intended for short-term use and should remain in position for at least three months (so thal a reasonable number of occasional, as well as habitual Users of the route are made aware of the change) but not fonger than six months, The permitied legends are: New Road Layout Ahead New Junction Ahead New Pedestrian Crossing Ahead New Traffic Signals Ahead New Roundabout Ahead No Left Turn Ahead No Right Turn Ahead No U-turn Ahead Although the use of warning signs at roadworks is discussed in a separate volume, ‘Traffic Control at Roadworks’ it is appropriate that the permitted signs (Signs 345-359) be defined here. Generally detailed descriptions are not provided as the symbols and/or worded messages are solf explanatory, Further signs included in “Trafic Control at Roadworks” but not included here are to be found in Chapter Two — Regulatory Signs. 3.13- B& 4 345, 349 Road wore Hard shoulder to be used as traffic lar ale End ons ~ End of Roadworks or Restriction. 350 Vehicles on hard shoulder to rejoin main carriageway = A Reduction in number of traffic anes. Sign face varies to show actual ayout. 351 Diversion of traffic to opposite carriageway 348 Chevron board Diversion => 352 Start of diversion Direction of arrow varies 3.14Jarmo sare! Diverted traffic a 353 fe direction sign on diversion route Some sare! Diverted traffic 354 Diversion direction sign ahead! ind of diversion 355 End of diversion Single File Traffic 356 Single file tratfic past site of roadworks 387 Warning of loose chippings on road surface 958 Pedestrian to follow route indicated by the arrow pres eLaLal Cerro Ries Eur) 359 Permitted legends are: Traffic Control Ahead (On Red Stop Here Road Anead Closed Road Closed No Construction Tratfic Construction Trafic Only Works Access Temporary Surface 3.15APPENDIX A SUPPLEMENTARY PLATE MESSAGES ‘ _ ENGLISH/ARABIC TYPE 343 Flood Census Road Ends Surveying Smoke TYPE 344 ww New Road Layout Ahead New Junction Ahead New Pedestrian Crossing Ahead New Tralfic Signals Ahead New Roundabout Ahead No Left Turn Ahead No Right Turn Ahead No U-Turn Ahead ‘TYPE 359 (On Red Stop Here Road Ahead Closed w Road Closed No Construction Traffic Construction Traffic Only Works Access ‘Temporary Surface i gaut ZA dLY! cla gl lalla Aajalsiyt aaa rer esi clas lina! Seb bs Russia Zaluue Jue! ols ret es gob apse qedy hb sua gb abl SLball asap jane dal Bapag Bigs 3L8I cael eae slys dal shell ga aL! g se coal ga alas! psa basal g sae reves SIC Ad yan eget se Bike Seok Late She Seb Gobel Jacl algl fous othe ee 3.16CHAPTER FOUR — INFORMATORY SIGNS Contents Section Tile Page No, 44 General 401 42 Information to Drivers 4.02 43 Information to Pedestrians 4.06 ‘Appendix A So Sizes of Informatory Signs 4.08 4.0044 Ss aa 442 . — 43 ww CHAPTER FOUR — INFORMATORY SIGNS GENERAL The signs illustrated in this Chapter give information to the road user regarding his location or facilities available in the vicinity. Unlike those specified in Chapters Two and Three, they have no regulatory or warning effect, Signs which give information to drivers display symbols and/or text and vary in size according to the ‘85th percentile vehicle speed. Symbol signs are generally available in either two or three sizes (see ‘Appendix A) and the appropriate size for each speed band is given in Table 4.1, together with character sizes for the text signs. ‘When siting these signs, care must be taken to ensure that the Minimum Clear Visibility Distance is achieved 85th ‘Symbol Signs oe Minimum Cl Percentile ‘available igne Visibility speed in eee Distance Aloph-height (mm) m kph 2sizes | 3sizes ‘Cenelght (mn) (Note 2) 0-60 Small Small 8 60 (60) 60-80 Large Medium 130 75 (75) Over 80 Large Large 170 100 (100) Note 1 : Aleph-height and x-height are defined in Part Two Chapter One Note 2: Slender obstructions such as trafic signal poles and lamp columns may be ignored Table 4.1 Sign Sizes and Visibility Distances Signs which give information to pedestrians are each available in one size only (see Appendix A). 40142 INFORMATION TO DRIVERS 421 TOWN OR AREA NAME a Clee Ge Bin Omran Q 400 401 422 U-TURN AHEAD w | 402 w a 423 NO THROUGH ROAD 403 Sign 400 indicates to drivers the name of the town or area that they are entering, The sign should be erected at the start of the buill-up area rather than the geographic boundary. ‘Sign 401 indicates to drivers thal they are leaving the Particular town or area. ‘Sign 402 is positioned on the median strip in advance of the entrance to a U-tum, The required siting distances are given in Table 42. 85th Siting Percentile distance speed kph (metres) 0-60 30 60-80 45 Over 80: 60 Table 4.2 Siting Distance for U-turn Sign These distances should be measured from the beginning of the deceleration lane. I none is provided then 100m should be added to the siting distance, Sign 403 is placed at the entry to any road where no through way for motor vehicle exists. It should be erected on both sides of the carriageway. 4.02424 425 ww 426 w 427 LANE DISCIPLINE Tb PARKING. HOSPITAL POLICE STATION Ere Ie eed 407 Sign 404 is used in urban areas in advance of a junction to indicate which lanes are available for particular traffic movements. The number of lanes shown on the sign should correspond with the lanes marked on the carriageway at the point where the sign is located. Sign 405 is used [0 indicate a parking place for vehicles, whether it be on-street parking bays or off-street parking places. The plate may be extended to include the distance or a direction arrow below the text, Alternatively the symbol may be incorporated in directional signing, as shown in Fig. 4.1 ljliw edge Car Park > ol jlew Car Park Sign 406 is used to advise drivers that they are approaching @ hospital or clinic. The plate may be extended fo include the distance or a direction arrow or the symbol incorporated in directional signing in a similar fashion to Sign 406. Sign 407 is used 0 indicate the location of a police station or police post, The distance or a direction arrow may be included below the text 4.03428 WEIGHBRIDGE ww eed ccnieeninl Sign 408 is used to indicate to drivers of heavy goods Weighbridge Ahead vehicles the location of a weighbridge station. The - ») distance or a direction atrow may be included below the text 408 4.29 EMERGENCY TELEPHONE w Sign 409 is used on Primary and Secondary Routes to indicate the direction to the nearest emergency telephone, where such a system is provided. The plate, which may also display the distance below the text, should be mounted parallel to the carriageway. 409 4.2.10 PRIVATE ACCESS SIGNS Signs 410 to 413 may be used to indicate the entry to 410 an and exit from private premises where there are two or more accesses to the main highway. They are ( normally erected in pairs with Signs 410 and 411 | oat back-to-back and Signs 412 and 413 back-to-back. | eee oy 412 413 w 404ww 4.211 COUNTDOWN MARKERS. 42.12 SERVICES ete Len a7 Hotel or Motel 420 Picnic Area IS) 418 ee 419 Refreshment la aan Camp Site 422 First Aid Station Countdown Markers 414 [0 416 are mounted below Sign 309 to warn drivers of their approach to a roundabout, The signs are located on both the nearside and off-side of the carriageway at 300m, 200m and 100m in advance of road Marking 02 (Give Way), When positioned on the. right hand side of the cartiageway the slope of the stipes is as illustrated When positioned on the left hand side, the slope is reversed, The colour of the signs must reflect the status of the road on which they are located, ie., green background with white stripes and border for Primary Routes, blue background with white stripes and border for Secondary Routes and white background with black stripes and border elsewhere, These signs may also be used at grade-separated junctions, on the nearside verge of the main carriageway, to countdown the distance to an off-ramp or slip road exit. They are located at 300m, 200m and 100m in advance of the point at which the deceleration lane commences, Signs 417 to 427 inclusive are used to indicate the presence of the services symbolised on the signs, They may display the distance to the facility or an arrow showing the direction in which the facility lies, as illustrated by signs 417 and 418. 4.05-o@ 423 424 Public Telephone Petrol Filling Station rere ww | 45 426 a7 Breakdown Information Mosque Service ottice 43 INFORMATION TO PEDESTRIANS 43.1 PEDESTRIAN CROSSING 428 Sign 428 is used to inform pedestrians of the location of an uncontrolled pedestrian crossing, It is NOT used where the crossing is controlled by traffic signals, Signs are erected at the crossing on both sides of the carriageway as shown in Fig, 42 Single carriageway Dual carriageway 4.2 Location of Sign 42843.2 PEDESTRIAN SIGNAL INSTRUCTION phe tata! placa! 9 ai! Push Button And Wait. 429 433 FOOTBRIDGE eres i ence 430 431 Sign 429 is provided at a pedestrian crossing. It may be incorporated within the push-button cabinet or appear as a separate plate. Sign 430 may be used to indicate the location of a footbridge. The plate may be extended to include a direction arrow below the text. Sign 431 may be used to indicate the location of a subway. The plate may be extended to include a direction arrow below the text. 4.07APPENDIX A — SIZES OF INFORMATORY SIGNS Sign Description Sign Dimension Aloph-height comments No. mm (acheight) mm 402 Usturn ahead 750 x 750 = 1000 X 1000 = 1250 X 1280, = 403 —_Nothrough road 500 x 500 . 44 Lane discipline 600 high = Wath varies depending S00 nigh 7 on numberof lanes and 1200 high = arrows 405 Parking 300 x” 400 225 (25) 600 x 800 8° (50) 800 x 1200 130 (75) 408 Hospital 300 x 400 425 (25) 600 x 800 85 (50) 900 x 1200 130 (75) 409 Emergency Telephone 225 x 450 35 (20) 410 Private Access Sign 425 x 425 85 (60) Entry 411 Private Access Sign 425 x 425 6 (G75) NoExil 412 Private Access Sign 425 x 425 8 (60) No Entry 413 Private Access Sign 425 x. 425 & 75) Ext 414 Countdown Marker 700 x 1450 170 (100) -S00-metres 418 Countdown Marker 700 x 1450 170 (100) 200metres 416 Countdown Marker 700 x 1460 170 (100) 100 metres 417 Hotel or Motel 00 x 300 85 (50) Distance or arrow may be 800 1350 130 (78) splayed 418 ‘Restaurant 600 x 900 85 (50) Distance or arrow may be 900 x 1960 130 (75) displayed 419 Refreshment 600 x 900, 85 (50) Distance or arrow may be 800 x 1350 13 (75) displayed 420 Pienic Area 600 x 900 85 (60) Distance or arrow may be 900 X 1380 130 (75) displayed 421 Camp Site 00 x 900 25 (50) Distance or arrow may be 900 X 1950 130 (75) Sispayed 422 ‘First Aid Station 600 x 900 85 (50) __Distance or arow may be 800 x 1350 130 (75) displayed 423. Public Telephone 600 x 900 85 (60) Distance or arrow may be 800 x 1350 130 (75) displayed 424 Petrol Filing Station 600 x 900 85 (50) Distance or arow may be 900 x 1350 130 (75) Gispiayed 425 Breakdown Service 00 x 1100 85 (50) __ Distance or arow may be 300 x 1650 130 (75) displayed 426 Information Ofice 600 x 1100 8 (75) Distance or arrow may be 800 x 1650 130 (60) Sisplayed 427 Mosque 000 x 1100 85. (60) Distance or arrow may be 900 X 1650 130 (75) Sispiayed 428 Pedestrian Crossing «500 x_ 500 = 429 Pedestrian Signal 200 x 175 2 (125) Instruction 490 Footbridge 525 x 275 65 (75) Direction arrow may be included below text 431 Subway 525 x 275 65 (975) Direction arrow may be included below text 408CHAPTER FIVE — ROAD MARKINGS AND STUDS Contents Section Title Page No. 51 General 501 5.2 Classification of Road Markings 501 5.3 Transverse Markings sor 5.4 Longitudinal Markings 5.03 5.5 Other Markings 508 56° — Worded Road Markings 5.18 5.7 Road Studs 520 5.8 _ Reflectorization of Carriageway Markings 527 5.9 Materials 521 Appendix A-F Road Marking Layouts 522.27 Appendix G Extended Character Set 528 5.0054 52 CHAPTER FIVE — ROAD MARKINGS AND STUDS GENERAL Road markings perform a vital task in the control, warning and guidance of road users. They may be Used in conjunction with road signs to supplement the information given by the sign or on their own to provide information that cannot be properly conveyed by signing, Whilst the benefits to be ganed from positive and clear road markings cannot be overstated it is, necessary to bear in mind their limitations. Designs that result in complicated arrangements of markings, e.g. channellising of trafic lanes over long distances or through ‘non-standard’ junctions, land which are relied on to segregate opposing traffic flows are unlikaly to be successful. Apart from ‘any problems due to driver comprehension, the very high rate of deterioration or markings experienced in Qatar dictates that reliance should not be placed solely on road markings as a means of control Itis strongly recommended trat careful consideration be given to the role of road markings and their design at as early a stage as possible in the formulation of designs for new or improved junctions, CLASSIFICATION OF ROAD MARKINGS Road markings may be grouped into three categories: (i) Transverse Markings ‘These markings are set across the carriageway and are associated with tratfic control by sign or signal. (i) Longitudinal markings play an important part, particularly in urban areas, in maintaining road safety by guiding and, where necessary, confining trafic to the appropriate lane. Their use also ensures that the available carriageway space may be used to its maximum capacity. (ii) Other Markings This group comprises those markings which, by means of their shape or colour, impart information or indicate the presence of restrictions to be observed. It should be noted that, except where specified otherwise, all road markings are whit. TRANSVERSE MARKINGS THE STOP LINE 500 500 y —. Marking 600 is used at traffic-signal controlled junctions to indicate where vehicles must stop when a red signal is displayed. Itis also used at priority junctions controlled by Sign 200 (STOP) to indicate where drivers should stop before proceeding into the junction, having ascertained that the major road is clear. The significance of the STOP sign and the criteria for its use are described in Chapter Two. {At signal-controlled junctions, the marking is installed as shown in Appendix ‘A. At priority junctions the marking should be installed on the line of the edge of the major carriageway (see Appendices B ‘and C), Only in exceptional circumstances may it be located elsewhere and it should never be positioned within 600mm of the path normally followed by the near side wheels of vehicles on the major road. 50153.2 534 ‘THE GIVE WAY LINE (PRIORITY JUNCTIONS) eo eos oe ee es ee a meee ee Marking 501 is used at priority junctions controlled by Sign 208 (Give Way) to indicate where drivers should yield to vehicles on the major road. It is always accompanied by Marking 503 (Give Way triangle), Its position in relation to the edge of the major carriageway is the same as that of Marking 500 (STOP) as shown in Appendix D, Where trafic joins the major road on an acceleration splay, Marking 501 should be provided from the centre line of the minor road for a distance equal to the width of that approach. The remaining length of the acceleration splay is marked with the appropriate edge of carriageway marking ‘THE GIVE WAY LINE (ROUNDABOUTS) 300, 700 ¥ See 502 Marking 602 is used at roundabouts to indicate where drivers should yield to vehicles already on the circulatory carriageway. It is always accompanied by Marking 503 (Give Way triangle). as shown in Appendices E and F. ‘At normal roundabouts, itis used in con) combination Sign 203/204 is usec. unction with Sign 203 (Give Way) bul at mini-roundabouts the THE GIVE WAY TRIANGLE fe 1250->4 ce [xo | 150 as | ae 503 Marking 503 is used with Markings 501 and 502 as described above. It is normally located with: its base 2 to 3 metres from the transverse marking but, exceptionally, this distance may be increased up toa maximum of 15 metres where the layout of the junction, visibility and/or vehicle speed on the minor road warrant such a move, 5.025.3.5 ROUNDABOUT WARNING MARKING (‘SHARKS TEETH’) 750 . ‘4000 |__¥ 504 ‘Marking 04 is used on all roundabout approaches. Where the 85th percentile speed on an approach is 80 kph. oF less, the markings are installed at 50 and 100 metres in advance of the Give Way line. Where the 85th percentiie speed exceeds 80 kph, these distances are increased to 100 and 200 metres, respectively. 5.4 LONGITUDINAL MARKINGS 5.4.1 LANE MARKINGS Lane markings are used to separate any traffic lane from its neighbour's). 2000 | 3000, ww sco 7000 | 2000 | 3000 ee a 120 120 | | w Marking 505 is used on Primary Routes where the 85th percentile speed is 80 k ph, oF less, and on all Secondary and Tertiary Routes. On Primary Routes where the 85th percentile speed exceeds 80 kph, Marking 606 should be used. 5.0354.2 WARNING MARKINGS 6000 6000 507 Marking 507 js substituted for Markings 805 and 506 to warn drivers of a hazard ahead and should be used in the following circumstances: (i) On the approaches to all junctions, as illustrated in the Appendices. The minimum number ‘of marking modules (i. line plus gap) varies according to the type of junction as detailed in Table 5.1 ‘Approach Major Minor Access 7 || Roads 85th percentile speed kph | 0-60 | Gs" | 0-60 | es" No. of Modules Priority Jet/Roundabouts 6 | | oo | Signal Controlled Junction 7 |e |e | 0 | 6 u-turn a | | Table 5.1 — Modules of Warning Marking at Junctions. It the distance between adjacent junctions is less than three times the length of the specified minimum number of modules, the warning marking should be continued through 5.04(il) Where the Forward Visibility Distance falls within the limits specified in Table 6.2 ww 85th percentile speed kph 0-45 45-60 60-80 Over 80 Upper Limit metres 125 175 225 300 Lower Limit metres 75 100 150 175 Note: 1. where the Forward visibity Distance falls below the lower it on single cariageway roads the Double Line System [Sect $4) should be used 2. Forwatd Vaiity istanes on dual cartageways should always exceed the lower limit fable 5.2 Visibility Criteria for Warning Marking 543 PROHIBITORY LINE apr 120 508 ‘Marking 608 indicates to drivers that they may not leave the lane in which they are travelling. It is used at priority junctions, trafic-signal controlled junctions and roundabouts to prevent weaving movement in the immediate vicinity of the junction, and extends 24 metres from the STOP or Give Way line, as, appropriate. 5.05DOUBLE LINE SYSTEM w 120 120 off 120 | 2000 w 7000 [a 509 120 120 2 510 Markings 509 and 510 are used on two-way single carriageway roads where the Forward Visibility Distance falls below the lower limits specified in Table 5.2. The continuous line indicates to drivers that they may not leave the lane in which they are travelling, Marking 509 is used where visibility is restricted in one direction only. Where itis restricted in both directions, Marking 510 is used, 5.065.45 EDGE OF CARRIAGEWAY MARKINGS w +" vo-ste “pew | Tt i 2500 2 g | 4 : 1000 . Keone | vot | 8 . 4 " 1000 3 a | : i | | . st 512 513 . Marking 511 is used to indicate the edge of carriageway ata road junction or lay-by. In urban ateas itis aiso used on certain roads fo delineate a continuous parking strip between the main Cariageway and kerbed edge. sn ic TT Marking 512 is used on roads in urban and suburban areas and on minor rural roads to indicate the Suge of cariageway where no hard shoulder has been provided and the edge of carriageway Is not defined by @ kerbiine Marking 513 is used to indicate the edge of carriageway (i) on all Primary and Secondary Routes (i) on all other roads where a hard shoulder (whether kerbed or not) has been provided (i) to replace Marking 512 where prohibitory or warning markings exist in the centre of the carriageway On Primary Routes, Marking 513 is coloured yellow and designated 513Y. w Nominal carriageway width — &m or 12m Minimum lane width 2.75m rH . sie = ————. 275 (325) for 150 (200) marking Fig. 51 Location of Edge of Carriageway Markings ww 50755 OTHER MARKINGS So eee 500 120 ' 8 w att e900 514 515 516 Markings 514, 515 and 616 are used on muli-lane approaches to trafic-signal controlled and priority junctions to indicate to drivers which lane they should take to reach their chosen exit. The direction of each arrow head may be varied as required but no more than two directions may be shown on any one arrow. On roads where the 85th percentile speed is 80 ko1, oF less, two arrows should be provided for each lane. Where the 85th percentile speed exceeds 80 k.p.n a third arrow should be added. ‘The distances in advance of the STOP or Give Way line at which the arrows should be installed are given in Table 53, Distance in metres. Speed ae 0-60 60-80 Over 80 A 1 18 20 25 2 45 60 i 3 = = 125 Table 5.3 Location of Lene Arrows ww 5.085.52 BIFURCATION ARROW cy 6:00 + 817 Marking 517 is used to indicate the divergence of a full wcth addtional lane trom the main carriage- w way. The additional ane may be either @ slip road, a deceleration lane, a tree right tur, a U-turn oF localised widening (@.9 in advance of a signal controled junction). The marking isnot intended to indi cate minor bifurcations such as deceleration tapers at Tunctions ‘The 32 metre arrow is used on roads where the 85th percentile speed exceeds 80 kph. Elsewhere, the 16 metre arrow is used. The ahead portion of the arrow is located centrally in the lane adjacent to the biturcation, with its tip approximately 20 metres (for the 32 metre arrow) or 10 metres (for ne 16 metre arrow) past the begin- ning of the divergence, in the direction of travel 553 WARNING ARROW i 750 Ld 200 250 oe (1050) (300) (350) . 2000 (3000) 4000 (6000) 518 Marking 518 is used in conjunction with Marking 607, under the following circumstances: (i) to warn drivers on two-way, single carriageway roads that they are approaching a double line marking (either Marking 509 with the solid line nearest to their lane, or Marking 510) and that they should return to and/or keep to the right In this case the arrow is positioned on the centre line of the carriageway, as shown in Fig. 52, replacing Marking 507. The distances in advance of the double line marking at which this occurs are given in Table 5.4 ~~ Fig. 5.2 Warning arrows in advance of double line system 5.09oo Distance (m) jaan ( speed Arrow = a ae ees 0-60 ao | a | — 6 60-80 30 | 6 | — 6 Over 80 30 | 96 | 186 9 Table 5.4 Location of Warning Arrow (ii)on @ one-way, mult-ane carriageway in advance of a narrowing where the number of lanes is reduced. The arrow is positioned in the riddle of the lane to be dropped (see Fig, 5.3) and may point to the left or right depending on which lane is to be lost. The distances in advance of the narrowing at which the arrows should be located are given in Table 54. 30m Point at which width starts to reduce __ —~, Fig. 5.3 Warning arrows at width reduction 5.54 CROSS HATCH AND CHEVRON MARKINGS, si 200| _\ J oyeicn ~ | so | . Ee 7 es 5.10Marking 519 is used to separate opposing streams of traffic prior to or following a physical separation such as the median strip or a traffic island Marking 520 is used to separate adjacent streams of traffic travelling in the same direction in advance (of physical separation. The marking may be used, with the direction of the chevrons reversed, to ‘extend a physical separation to control merging streams of trafic. Marking 521 is substituted for Marking 520 on Primary Routes, 5.5.5 MINIL-ROUNDABOUT MARKING ™% \ o -— 3500-7000 5000-10 000 diameter 522 Marking 522 may be used to convert existing priority junctions of urban local and access roads to roundabout operation. This may be required where the pattern of traffic movement has altered and/or the operation of the junction results in unacceptable congestion on the minor approaches). The marking has the meaning that any vehicle approaching the Give Way line must give priority to those vehicles approaching from the ahead or left directions whose route through the junction causes them to cross the path of the first vehicle. The principle is illustrated in Appendix F. bat5.56 PEDESTRIAN CROSSING MARKINGS 00-1900 sTups a] AT 600 coe CENTRES 00-1900 523 Marking 523 is used to define an area of carriageway that may be used by pedestrians for crossing the road w Toot w Fig, 54 Pedestrian Crossing at Trafic-Signals Where the crossing is controlled by pedestrian operated trafic signals ors ata trafic signal controled junction, the marking is positioned 1 metre beyond the primary signal pole, as ilustrated in Figure 5.4 w 512wre - mS] — na 2 ZIG-ZAG DETAIL L 524 Marking 524 is provided in advance of Marking 523 where the crossing is not controlled by traffic signals. It not only warns of the presence of the crossing but also has the meaning that no vehicle may stop within the length of the marking excep! to permit a pedestrian to cross the road. [At uncontrolled crossings, Marking 523 and 524 are postioned as illustrated in Figures §.5 and 56 It Should be noted that Sign 246 and Marking 27 may be used {0 prevent parking on the ext from the w Grossing should i be considered necessary —= a ma-—— > oo : Fig. 5.5 Uncontrolled Crossing on Single Carriageway Fig. 5.6 Uncontrolled Crossing on Dual Carriageway 5.135.57 BOX JUNCTION MARKING 2000 (2500) when the shortest boundary is more than 9000 mm rv a a7 / 2 <3 190 & ~ ele WA gig 8 \ Stet tne 150° max. ve ~~ 4 NX y qe 10% max of breadth, 3000 min 10% max. of bk length 30000 max a w 525 ‘Marking 525 may be used at junctions in order to prohibit queueing within the junction which prevents cther movements taking place. A driver may enter the junction only when his ext is clear unless he wishes to turn let in which case he may enter i his further movement is prevented solely by oncoming trafic. He may not enter i that tralic is stationary This marking has a regulatory effect (indicated by its yellow colour) and will requie enforcement by the Talc Police. Consequently al cases of intended use must be relerred to the Ministry of Public Works for consideration ‘The way in which the marking is constructed is described below (i) Rectangular junctions (a) The diagonals are set out at right angles (or as near as possible) to each other (b) The boundary lines are drawn w (c) The grid is infiled with the lines being set parallel to the diagonals at 2 metre intenvals Wire the box is much longer than it is wide, itis set out as shown ~ Fig. 5.7 Rectangular Box 14Where the box is required on one half of the carriageway only, itis set out as a full box but only half the markings are provided, as shown. Fig. 5.8 Half Box (il) Non-rectangular junctions (@) A boundary line is drawn across each arm at right angles (or as near as possible) to its centre lina, The perimeter is completed by following the intervening kerbiines, (b) The diagonals A — B and C — D are drawn, as shown, to intersect at right angles, oF as near as possible, (c) The grid is inflled as betore. Fig. 5.9 Non-Rectangular Boxes 5155.5.8 WAITING RESTRICTION MARKINGS Kerb A [50 soot ak 526 Kero. 109 ww 827 Markings 526 and 527 are provided on the nearside edge of carriageway on roads subject 10 waiting restrictions to indicate the length(s) of road over which the restrictions are in force. Marking 526 is used where parking is prohibited between certain hours only and Marking 527 is used where parking is prohibited at all times, They are both coloured yellow. ‘These markings supplement Signs 246 and 247 and may be considered as being for the guidance of the public as itis the presence of the signs that enforces the restriction. 5.5.9 KERB MARKINGS AT JUNCTIONS PAVING PAINTED KERB TONE 4 oe PAVEMENT 528 ‘Marking 528 should be applied to all kerbs in the vicinity of a junction, to highlight its presence. The kerbs are painted black and white 5.165.5.10 PARKING BAY MARKINGS . ap a I 100 + 8 100 3 7000 eee Kerb Line 529 ww 500 1000 Kerb Line ww 530 Markings 529 and 530 are used to define parking bays on or adjacent to the highway w : 5175.5.11 ROAD HUMP MARKINGS 500, 500 _500-1000 Kerb 531 Marking 531 is used to indicate the position and extent of a speed control road hump. Type 855 studs should be provided on both approaches, as shown. 5.6 WORDED ROAD MARKINGS 56.1 GENERAL ‘Markings 532 and §33 are he only worded road markings approved for general use. Other legends may only be used where the appropriale message cannot be conveyed by conventional signing and road markings. ‘The characters forming the legend are elongeled vertically to improve their legibility to drivers approaching at speed. The slongation is based on a unit aleph-height of 680mm (x-neight = 400mm) and is dependent on vehicle approach speed, as specified in Table 55. The Arabic and English character sets are illustrated in Appendix G. 85th percentilo Ratio of Elongation speed i = Vertical | Horizontal Under 45 3 1 Over 45 5 1 Table 6.5 Character Sizes 5.18562 STOP MARKING 532 Marking 532 may only be used to supplement Sign 200 and Marking 500, as illus and must NOT be used under any other circumstances, | vy we ‘Marking 533 may be used to supplement warning signs on the approach to a hazard or junction, 6.8 sharp bend at the end of a long straight section of high speed road ated in Appendix B, 563 SLOW MARKING It must be emphasised that this marking should only be used where absolutely necessary, as ‘experience has shown that over provision results in the warning message being ignored 5.1957 ROAD STUDS 87.1 REFLECTING ROAD STUDS Reflecting studs are normally provided on all roads away trom areas of street lighting, although certain lit roads may require studs, as directed by the Ministry of Public Works. The stud type and colour, and the carriageway marking with which they are associated, are shown in Table 56 stud] Colour Use Road Marking Spacing in metres for Type Single C'way | _Dusl C'way 850 | white/wnite | Lane Marking } 505, 506 18 7 550 | whiteWhite | Lane Marking | 507, 508, 509 9 - 510 351 | White/Red | Lane Marking | 505, 506 = 18 551 | White/Red | Lane Marking | 507 = 9 ~ 552 | Red/Red Nearside 512,513 18 18 Edge Marking s52| Red/Red | Edge Marking | 519,520,521 3 3 553 | Amber/Red | Offside Edge | 512,513 - 18 Marking 553 | Amber/Red | Offside Edge | 519, 620,521 3 3 Marking 554 | Green/Greon | _Nearside sit 8 8 Edge Marking 555 | Amber/Amber | Road Hump | 531 ‘Transverse at 2m centres Not: vnare wsedin conjunction wih Making 08, the stds wil be psioned othe nearsie of he marking, eave fo ale sopreacing the junction - Table 6.6 Road Studs and Associated Corrlageway Markings 572 _NON-REFLECTING ROAD STUDS 5721 WHITE CERAMIC STUDS ‘These studs may be used as a substitute for rellective road studs in urban areas where street lighting is provided. Al present, they may be used only in conjunction with the following road markings: 505509 508 «510 307 ther applications ofthese studs, e.9. at junctions where the wear rate of thermoplastic or painted road markings is particularly high, are sill under study by the Ministry of Public Works. 5722 SQUARE METALLIC STUDS — ‘These studs are used to warn of the approach to, and to delineate, a pedestrian crossing. 5.2058 581 5.9 594 593 REFLECTORIZATION OF CARRIAGEWAY MARKINGS Carriageway markings are normally reflectorized by the addition of spherical glass beads to the marking material during mixing and by the application of further beads to the surface of the marking during application, This extra retlectorization is not suitable for lane and hand-aid markings in areas where the obliteration of markings is a problem, MATERIALS MARKINGS. Carriageway markings will normally be formed using superimposed Thermoplastic or Hot Sprayed Plastic complying with the Qatar National Building Specification (QNBS) Clauses 19-405 and 19-406, Alternatively the following materials are being evaluated by the Ministry of Public Works, whose approval must be obtained prior to their use. () Twin Pack Polyurethens (Marine) paint. (i) Prefabricated Sheet Material Paint is used for Marking 827 REFLECTING ROAD STUDS Reflecting road studs used in Qatar are “double-sided”, having a multi-efiex lens strip of the appropriate colour set on the two faces perpendicular to the direction of traffic flow. ‘Those studs intended for permanent use should have the lens strips housed in a cast aluminium base with integral anti-shear pin, This pin is inserted into a pre-drilled hole in the road surface and anchored by means of an adhesive, grout or hot poured bitumen. Studs which have no anti-shear pin and are bonded to the road surface by an adhesive, e.g. epoxy ‘cement, should only be used in temporary situations such as the diversion of trafic lanes at roadworks. Exceptionally, they may be used in lacations where they would be subject to very litle trafic loading 8.9. with the offside edge of carriageway marking on a dual carriageway road NON-REFLECTING ROAD STUDS When used as a lane marking these must be of white ceramic material, 100 mm diameter. Square metallic, aluminium or stainless steel studs are used 10 delineate or warn of pedestrian crossings. 521