DETECTING BASICS TREASURE VIEW (GO‑FIND 44/66 only)

Treasure View LEDs light up when a metal object has been detected.
QUICK START GUIDE As you get closer to the target, more LEDs illuminate.
STEP 1. POWER ON ON switch RED indicates an iron metal object (possibly trash).
Switch your detector on. GREEN indicates a non-iron metal object (possibly treasure).
ORANGE indicates Pinpoint mode for all metal objects.
The LCD will light up with several icons.
STEP 2. BEGIN DETECTING
Sweep the coil over the ground in a side-to-side motion.
The detector will light up and beep when a metal object is found.
LEDs will illuminate from left to right when Pinpoint is off.

SWEEP LEVEL Keep the coil 1–2 ITEM FOUND The detector will
LEDs will illuminate towards the center when Pinpoint in on.
inches (2–3 cm) above and parallel to light up and beep when a target is
This helps identify the exact location of the object.
the ground at all times. discovered.

ICON DESCRIPTIONS
When a metal object is detected, the corresponding icon will flash on the
control panel to indicate the target type. If the icon is turned off (not visible)
then these object types will not be detected.
SPEED Sweep the coil over the ADJUSTMENT The detector should
ground in a side-to-side motion, an be straight with your forearm and
average sweep speed is 1–2 seconds feel light and comfortable when you
from left to right. pick it up.

Iron objects, nails and Rings, pull tabs and lower

50 ft (15 m)
horseshoes. value coins.
OVERLAP SWEEP Slightly overlap the SPACE Recommended distance is
previous sweep to ensure full ground 50 feet (15 m) apart when multiple Aluminium foil and lower value Low and high value coins and
coverage. users are scanning an area. coins. screw caps.

CONTROL PANEL FIND MODES

9 FIND modes allow you to search for specific groups of metal objects by
accepting or rejecting detection. No need to dig the trash; just the treasure!
Cycle through the different modes using the Find button.

10 GO‑FIND 22 GO‑FIND 44 GO‑FIND 66

11 8 Select from 2 find modes: Select from 3 find modes: Select from 4 find modes:

1. 1. 1.

7 2. 2. 2.
12 6 3. 3.

4.
5
1

2
DETECTOR SOUNDS
3 The detector beeps when an object is detected. This sound can be heard
through the detector speaker or through ear buds/headphones connected to
4 the audio output socket (refer to control panel diagram).

1. POWER SWITCH (ON/OFF) 8. DEPTH INDICATION

Shallow | Medium | Deep GO‑FIND 22 GO‑FIND 44 GO‑FIND 66
2. EAR BUDS OUTPUT
9. TREASURE VIEW LED 2 different audio tones: 3 different audio tones: 4 different audio tones:
3. SENSITIVITY
Red and green LEDs help you quickly
Increase for more detecting depth. You
identify treasure from trash.
may need to decrease this if there is high
(GO‑FIND 44/66 only)
noise interference or false signals.
10. FIND ICONS (× 4)
4. PINPOINT (GO‑FIND 44/66 only)
Determine the exact location of a target. 11. BATTERY LEVEL
5. VOLUME 12. BLUETOOTH (GO‑FIND 44/66 only)
6. BACKLIGHT (GO‑FIND 44/66 only) AUDIO OUTPUT LOW TONE: Iron targets (such as nails) produce the lowest tone.
1/8" connector with speaker at rear. MID 1 TONE (GO‑FIND 44/66 ONLY): Less valuable metals produce a lower medium tone.
7. FIND MODE MID 2 TONE (GO‑FIND 66 ONLY): Higher value metals produce a higher medium tone.
Detect and reject metal objects. HIGH TONE: Silver and copper targets produce the highest tone.
 to lock into position.   To retract shaft, firmly tap on the base of the coil.
(failure to release handle correctly will result in damage). (Refer to ‘Detecting Basics’). Close the camlock lever
unlock buttons while folding handle flat. upper shaft to desired length, for your height you hear it click into place.
  To release handle, press and hold down both STEP 6. Release the camlock lever to adjust the STEP 5. Fully extend the lower shaft until you

over tighten.
the nut to fix the coil position. Be careful not to
body of detector as shown. with the ground (Refer to ‘Detecting Basics’). Tighten (typically just under your elbow).
STEP 2. Then apply selected skin to STEP 4. Fold out the search coil to detect parallel STEP 3. Slide out the armrest to desired length

4 x AA

from selected skin.

To apply, simply peel backing paper (not included).
STEP 1. There are two skins provided. STEP 2. Insert 4 x 1.5V AA (LR6) batteries STEP 1. Lift the handle.

SKIN APPLICATION DETECTOR SET UP

DOWNLOAD APP CODE OF ETHICS

www.itunes.com | play.google.com 1. Respect the rights and property
of others.
2. Observe all laws, whether GETTING STARTED GUIDE
national, state or local.
3. Never destroy historical or
NOTE: archaeological treasures.
GO‑FIND App works with 4. Leave the land and vegetation
GO‑FIND 44/66 only. as it was.
Pro App FREE with GO‑FIND 66 only. 5. Always obtain permission before
BLUETOOTH SMART COMPATIBLE searching sites.
GO‑FIND 44/66 are BLUETOOTH SMART 6. Always fill in your holes after
compatible with iOS 8 and Android 4.3 mobile digging.
operating systems, and above.

WARRANTY TERMS However, there is no guarantee that interference

This product has a 2 year limited warranty from the will not occur in a particular installation. If this
time of purchase. Please refer to www.minelab.com equipment does cause harmful interference to radio
for further warranty information. or television reception, which can be determined
by turning the equipment off and on, the user is
COMPLIANCE encouraged to try to correct the interference by one
or more of the following measures:
Information to the User (FCC Part 15.105)
NOTE: Class B Devices • Reorient or relocate the receiving antenna
• Increase the separation between the equipment
This equipment has been tested and found to and receiver
comply with the limits for a Class B digital device, • Connect the equipment into an outlet on a
pursuant to part 15 of the FCC Rules. These limits are circuit different from that to which the receiver
designed to provide reasonable protection against is connected
harmful interference in a residential installation. • Consult the dealer or an experienced radio/TV
This equipment generates, uses and can radiate technician for help
radio frequency energy and, if not installed and Warning: Any changes or modifications not
used in accordance with the instructions, may cause expressively approved by Minelab Electronics could
harmful interference to radio communications. void the user’s authority to operate this equipment.

North & South America Europe

Minelab Americas Inc Minelab International Ltd
+1 630 401 8150 +353 21 423 2352
[email protected] [email protected]
Asia Pacific Middle East & Africa
Minelab Electronics Pty Ltd Minelab MEA General Trading LLC
+61 8 8238 0888 T: +971 4 254 9995
[email protected] [email protected]

www.minelab.com
Minelab® and GO-FIND® are trademarks of Minelab Electronics Pty. Ltd. Images and graphics are for illustration purposes only;
product configuration and specifications may vary from those shown.
4901-0230-2