Scribd
Upload
462 views1 page

TK-35 Bitumen FT VG-40 ( - 35-2020) 14-12-2020

The inspection report summarizes the test results for a sample of Paving Bitumen Grade VG 40 taken from Tank Number 35 at HPCL-VR QC LAB. All characteristics tested, including density, viscosity, flash point, solubility, penetration, softening point, and residue tests met the requirements of IS 73:2013 for Paving Bitumen Grade VG 40. The sample was approved and the tank was released for use.

Uploaded by

JP Autoclavers & Co.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
462 views1 page

TK-35 Bitumen FT VG-40 ( - 35-2020) 14-12-2020

The inspection report summarizes the test results for a sample of Paving Bitumen Grade VG 40 taken from Tank Number 35 at HPCL-VR QC LAB. All characteristics tested, including density, viscosity, flash point, solubility, penetration, softening point, and residue tests met the requirements of IS 73:2013 for Paving Bitumen Grade VG 40. The sample was approved and the tank was released for use.

Uploaded by

JP Autoclavers & Co.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

FINISHED PRODUCT INSPECTION REPORT

Product : Paving Bitumen Grade VG 40


IS 73:2013 ULR No TC740620000001435F
Testing Lab : HPCL-VR QC LAB Customer Name : HPCL-VR Operation Department
Tank Number : 35 Date Sampled : 13-12-2020
Type of Sample : Average Date Tested : 13&14-12-2020
Batch No : 35/2020 Date Released : 14-12-2020

CHARACTERISTICS INSPECTIONS REQUIREMENT METHOD OF TEST


Density @15 deg C, g/cc 1.0425 To Report IS 1202
Absolute viscosity at 60 deg C, Poises 4694 3200 to 4800 IS 1206 (Part 2)
Kinematic viscosity at 135 deg C, cSt 570.6 400 min. IS 1206 (Part 3)
Flash Point Cleveland open cup, deg C >220 220 min. IS 1448 P-69
Solubility in trichloroethylene, percent 99.9 99.0 min. IS 1216
Penetration @25 deg C, 100g, 5sec,1/10mm 42 35 min. IS 1203
Softening point (R & B), deg C 51.0 50 min. IS 1205
Tests on residue from rolling thin film oven
tests
1. Viscosity ratio at 60 deg C 2.11 4.0 max. IS 1206 (Part 2)
2. Ductility at 25° C,cm after thin-film >140 25 min. IS 1208

Remarks:

The results relate only to the sample tested and the sample meets IS 73 : 2013 (Fourth Revision),Amendment
No.1 requirements for Paving Bitumen, Grade VG 40 for the parameters inspected. The test report shall not be
reproduced except in full, without written approval of the Laboratory. Sample drawn by operation person.

Test Report Test Report Dr.N.Rambabu


Prepared by : rsv prasad Reviewed by Chief.Manager- QC
Authorized Signatory

Routing
Planner / Lab / Excise Tank Released by : Chief Mgr/DGM-Opns

You might also like