Product Specifications

CVV2NPX308.208R
Multiband Antenna, 790–960 MHz 65° horizontal beamwidth, 2x 1695-2690 MHz 65°
horizontal beamwidth and dual beam 1695-2180 MHz 33° horizontal beamwidth,
internal electrical tilt with manual override. Bands cascaded SRET
l Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical
tilt with manual override on all arrays

l All Internal RET actuators are connected in “Cascaded SRET” configuration

Electrical Specifications
HB Dual HB Dual
LB LB HB HB HB
Beam2 Beam2
790– 890– 1695– 1920– 2300–
Frequency Band, MHz 1695–1920 1920–2180
890 960 1920 2180 2690
Gain, dBi 15.8 16.1 16.2 16.9 17.3 16.5 18.1
Beam Centers, Horizontal, degrees ±32 ±30
Beamwidth, Horizontal, degrees 69 68 66 67 65 36 31
Beamwidth, Vertical, degrees 11.1 10.2 10.1 9.0 7.3 10.3 9.1
Beam Tilt, degrees 0–10 0–10 0–10 0–10 0–10 0–10 0–10
USLS (First Lobe), dB 18 18 18 18 18 18 18
Null Fill, dB -22 -22 -22 -22 -22 -22 -22
Front-to-Back Ratio at 180°, dB 32 36 31 30 30 27 31
CPR at Boresight, dB 16 15 17 16 16 10 11
CPR at Sector, dB 10 13 10 10 0
Isolation, dB 28 28 30 30 30 25 25
Isolation, Intersystem, dB 22 22
Isolation, Beam to Beam, dB 18 18
1.5 | 1.5 |
VSWR | Return Loss, dB 14.0 14.0
1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0

PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum,
300 300 250 250 250 250 250
watts
Polarization ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*

1695– 1920– 2300– 1695– 1920–
Frequency Band, MHz 790–890 890–960
1920 2180 2690 1920 2180
Gain by all Beam Tilts, average,
15.7 15.9 15.9 16.5 16.9 15.8 17.5
dBi
Gain by all Beam Tilts Tolerance,
±0.2 ±0.1 ±0.3 ±0.5 ±0.7 ±1.1 ±0.9
dB
0 ° | 15.7 0 ° | 16.0 0 ° | 16.0 0 ° | 16.5 0 ° | 17.1 0 ° | 15.9 0 ° | 17.6

Gain by Beam Tilt, average, dBi 5 ° | 15.7 5 ° | 15.9 5 ° | 15.9 5 ° | 16.5 5 ° | 16.9 5 ° | 15.9 5 ° | 17.6
10 ° | 15.6 10 ° | 15.8 10 ° | 15.9 10 ° | 16.3 10 ° | 16.5 10 ° | 15.6 10 ° | 17.3

Beamwidth, Horizontal
±0.7 ±0.5 ±2.8 ±4.3 ±7.6 ±3.4 ±2.1
Tolerance, degrees
Beamwidth, Vertical Tolerance,
±0.5 ±0.4 ±0.7 ±0.6 ±0.6 ±0.6 ±0.7
degrees
USLS, beampeak to 20° above
18 18 18 18 18 18 18
beampeak, dB
Front-to-Back Total Power at
26 26 29 29 29 24 28
180° ± 30°, dB
CPR at Boresight, dB 16 16 17 20 20 13 15
CPR at Sector, dB 12 14 12 13 6

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 1 of 5
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: January 24, 2017 February 2, 2017
Product Specifications
CVV2NPX308.208R

* CommScope® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA,
download the whitepaper Time to Raise the Bar on BSAs.

Array Layout

General Specifications
Operating Frequency Band 1695 – 2180 MHz | 1695 – 2690 MHz | 790 – 960 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage

Mechanical Specifications
RF Connector Quantity, total 10

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 2 of 5
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: January 24, 2017 February 2, 2017
Product Specifications
CVV2NPX308.208R

RF Connector Quantity, low band 2

RF Connector Quantity, high band 8
RF Connector Interface 7-16 DIN Female
Color Gray
Grounding Type RF connector inner conductor and body grounded to reflector and
mounting bracket
Radiator Material Brass | Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 866.0 N @ 150 km/h
194.7 lbf @ 150 km/h
Wind Loading, lateral 279.0 N @ 150 km/h
62.7 lbf @ 150 km/h
Wind Loading, rear 900.0 N @ 150 km/h
202.3 lbf @ 150 km/h
Wind Speed, maximum 241 km/h | 150 mph

Dimensions
Length 2065.0 mm | 81.3 in
Width 350.0 mm | 13.8 in
Depth 208.0 mm | 8.2 in
Net Weight, without mounting kit 35.5 kg | 78.3 lb

Remote Electrical Tilt (RET) Information

Input Voltage 10–30 Vdc
Internal RET Low band (1) | Low band (4)
Power Consumption, idle state, maximum 2.0 W
Power Consumption, normal conditions, maximum 13.0 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 1 male

Packed Dimensions
Length 2250.0 mm | 88.6 in
Width 436.0 mm | 17.2 in
Depth 320.0 mm | 12.6 in
Shipping Weight 53.0 kg | 116.8 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
China RoHS SJ/T 11364-2006 Above Maximum Concentration Value (MCV)
ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 3 of 5
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: January 24, 2017 February 2, 2017
Product Specifications
CVV2NPX308.208R

Included Products
T-029-GL-E — Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (50-115mm) OD round members for panel antennas. Includes
2 clamp sets.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 4 of 5
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: January 24, 2017 February 2, 2017
Product Specifications
T-029
029--GL
GL--E
Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (50-115mm) OD round members for
panel antennas. Includes 2 clamp sets.

General Specifications
Mount Type Pipe mounts
Application Outdoor
Includes Brackets | Hardware
Package Quantity 1

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–8°

Dimensions
Antenna-to-Pipe Distance 85.0 mm | 3.3 in
Bracket-to-Bracket Distance 1400.0 mm | 55.1 in
Compatible Diameter, maximum 115.0 mm | 4.5 in
Compatible Diameter, minimum 50.0 mm | 2.0 in
Compatible Length, maximum 2850.0 mm | 112.2 in
Compatible Length, minimum 1500.0 mm | 59.1 in
Net Weight 6.0 kg | 13.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
China RoHS SJ/T 11364-2006 Above Maximum Concentration Value (MCV)
ISO 9001:2008 Designed, manufactured and/or distributed under this quality management system

©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. page 5 of 5
All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: November 5, 2016 February 2, 2017