Seismic Co-efficient calculation as per NBCC| 4.1.8.11.

Equivalent Static Force Procedure for Structures Satisfying the Conditions of Article 4.1.8.7.

As per NBCC 2010, sec 4.1.8.11 (1) Equivalent Static Procedure shall be used for the structures that meet any of the following conditions
V=𝑆(𝑇_𝑎 ) 𝑀_𝑣 𝐼_𝐸 𝑊/(𝑅_𝑑 𝑅_0)
4.1.8.7 i IE. Fa.Sa(0.2) < 0.35 Not satisfied
ii Height of structure < 60m Ta = 0.05 (hn)3/4 Satisfied conditions : satisfied
iii Structures with structural irregularity that are less than 20m height have Ta < 0.5 Satisfied
4.1.8.11. (2) a. Lateral Earthquake Cooefficient, V = 0.43 Constant
𝑆(𝑇)=𝐹𝑎𝑆𝑎(0.2)𝑓𝑜𝑟 𝑇≤0.2𝑠
b. Site Class 𝑆(𝑇)=𝐹𝑣𝑆𝑎(0.5)"or " 𝐹𝑎𝑆𝑎"(0.2), whichever is smaller for T = 0.5 s" = C
4.1.8.4.A(For Stiff Soil)
c.
4.1.8.11. (3).(c) The fundamental lateral period for other structures, Ta = 0.07 seconds
𝑆(𝑇)=𝐹𝑣𝑆𝑎(1.0)𝑓𝑜𝑟 𝑇=1.0𝑠
𝑆(𝑇)=𝐹𝑣𝑆𝑎(2.0)𝑓𝑜𝑟 𝑇=2.0𝑠
OK
𝑆(𝑇)=𝐹𝑣𝑆𝑎(2.0)/2 𝑓𝑜𝑟 𝑇≥4.0𝑠
d.
The height of the structure hn = 1.7 m

4.1.8.4. (7) e. Design Spectral acceleration S(T) 𝑆𝑎(0.5) = 0.64 Constant

𝑆𝑎(0.2) = 0.31 Constant
smallest value = 0.31 Constant
𝑆𝑎(1.0) = 0.14 Constant
= 0.05 Constant
𝑆𝑎(2.0) = 0.02 Constant
𝑆𝑎(0.2)/𝑆𝑎(2.0) =
Enter S(T) from the above calculated values for the corresponding Ta = 0.64 Constant
f. Spectral acceleration for 5% damping as per Qubec city = 0.31 Constant
Spectral acceleration for 5% damping as per Qubec city = 0.64 Constant
g.
Table 4.1.8.4. (B) h. Acceleration-based site coefficient (Fa) Fa = 1 Constant
Spectral acceleration for 5% damping as per Qubec city = 0.14 Constant
i.
j. V > 𝑆(2.0) 𝑀_𝑣 𝐼_𝐸 𝑊/(𝑅_𝑑 𝑅_0)
Table 4.1.8.4. (C) Velocity-based site coefficient (Fv) Fv = 1 Constant
k. Spectral acceleration for 5% damping as per Qubec city = 0.047 Constant

Table 4.1.8.11 l. = 13.61702 >=8

Table 4.1.8.11 m. The Higher mode factor (Mv) 1 Constant

= 1.3 Constant
4.1.8.5.(1) n. The earthquake importance factor IE

Table 4.1.8.9 (Other

steel not defined = 1.5 Constant
above) o. Ductlity related Force Modification Factors, Rd,

Table 4.1.8.9 (Other

steel not defined = 1.3 Constant
above) p. Overstrength-Related Force Modification Factors, R0,
q. Weight of Skid factor(W) = 1 Constant
4.1.8.11. (2b) r. For other strutures , = 0.03 OK

Seismic Load calculation

a. Factored Operating weight = 19.875 kN
Seismic Forces along X and Z directions
a. Forces in X-Direction=Fx = 8.48 kN
b. Forces in Z-Direction=Fz = 8.48 kN
Seismic Moments along X and Z directions and Anchor forces
a. Moments in X-Direction=Mx = 7.208 kN-m
b. Moments in Z-Direction=Mz = 7.208 kN-m
c. Total number of bolts = 6 Numbers
d. Shear force on each bolt = 1.413333 kN
e. Distance from Center of skid to the nearest Bolts distance = 0.876 m
f. Number of Bolts at nearest distance = 2 Numbers
g. Tension force Fy acting on each bolt = 4.114155 kN
 Seismic load calculation as per NBCC 2010| 4.1.8.11

4.1.8.18 a. Lateral force, Vp Vp= 〖 0.3𝐹_𝑎 𝑆_𝑎 〗 _ ( 〖 0.2) 𝐼 〗 _(𝐸 ) 𝑆_(𝑝 ) 𝑊_𝑝
Table 4.1.8.4B b. Site coeff. Fa
c. Sa(0.2)
4.1.8.5 d. Imprtance factor, Ie
e. Sp = CpArAx/Rp
Table 4.1.8.18 f. Element or component factor, Cp
Table 4.1.8.18 g. component force amplification factor, Ar
4.1.8.18 sent-1
h. Height factor, Ax = (1 + 2hx/hn )
hx
hn
Table 4.1.8.18 i. Component response modification factor, Rp
j. Weight factor
010| 4.1.8.11

0.2) 𝐼 〗 _(𝐸 ) 𝑆_(𝑝 ) =𝑊_𝑝 ) 0.42

= 1.00 as per site class C
= 0.64
= 1.30
= 1.67
= 1.00 flexible or flexibly connected
= 2.50 flexible or flexibly connected

= 1.00
= 0.00
= 3.00
= 1.5
= 1.00
 1 Equipment time period:
1 Natural Frequency of Centrifuge = 10 Hz
2 Natural time period of Centrifuge = 0.1 sec

2 Seismic Load calculation

1 Total weight of equipment = 6075 kg with 1.5 factor
2 No of supports = 4 no
3 No of anchor bolts per support = 4 no
4 Size of anchor bolt = 12 mm
5 Least distance between the C/L of anchors = 1.05 m
6 Height of CG = 1.275 m
7 Seismic coefficient = 0.42
8 Total seismic base shear = 2551.5 kg
9 Seismic shear per anchor bolt = 637.88 kg
10 Overturning moment = 3253.16 kgm
11 Tension force = 3098.25 kg
12 Critical load combination for anchor design = 1.0D + 1.0E (Table 4.1.3.2.A_ NBC 2010)
13 Resulting tension force per bolt = 30.38 kg

3 Dynamic Load details (Critical run down condition)

Vertical upper load = -4497 lb

Vertical downward load = -17985 lb

Horizontal upper load = 2248 lb

Horizontal downward load = -2248 lb

Per support
Vertical upper load = -1124.25 lb
Vertical lower load = -4496.25 lb

Horizontal upper load = 562 lb

Horizontal lower load = -562 lb
 Assumptions

1 Height on CG 2/3rd overall height

2 Pedestal size
3 Thickness of grade slab 200mm
4 No grout assumed
5 Base plate thickness 12mm
6 Equipment inside the building