DISC BRAKE ROTORS & DRUM BRAKES

catalogue - 2010/11
V130910

CONTENTS
Vehicle Make Page # Vehicle Make Page #

ALFA ROMEO 17 MASERATI 121

AUDI 20 MAZDA 122
BMW 24 MAZDA - 4WD / SUV / VAN 126
chevrolet 38 MERCEDES BENZ 127
CHRYSLER / DODGE 44 MERCEDES BENZ - 4WD / SUV 131
CITROEN 46 MG 140
DAEWOO 53 MINI - cooper 140
DAIHATSU 54 MITSUBISHI 142
daimler 56 MITSUBISHI - 4WD / SUV / VAN 147
EUNOS 57 MORRIS - AUSTIN 150
FERRARI 57 NISSAN 151
Fiat 58 NISSAN - 4WD / SUV / VAN 157
FORD 61 OPEL 160
FORD - tickford / FPV 65 PEUGEOT 161
FORD - TRUCKS 74 Pontiac 163
gmc 79 Porsche 164
hillman 83 proton 166
HOLDEN 86 RANGEROVER 166
HOLDEN - HSV 88 RENAULT 167
HOLDEN - commercial / 4wd 100 ROlls royce 169
HONDA 102 Rover 169
HUMBER 108 SAAB 170
HUMMER 108 SEAT 171
HYUNDAI 109 Ssanyong 171
HYUNDAI - 4WD / SUV 111 SKODA 171
ISUZU 112 SUBARU 172
JAGUAR 113 SUBARU WRX UPGRADE 177
JEEP / CHRYSLER 114 SUZUKI 178
KIA 115 TOYOTA 180
KIA - 4WD / SUV 116 TOYOTA - 4WD / SUV / VAN 187
LADA 116 TRIUMPH 193
LAncia 116 VOLKSWAGEN 194
LAndrover / RANGE ROVER 117 VOLKSWAGEN COMMERCIAL 198
lexus 119 VOLVO 201
LEYLAND 120 WeightS & DIMENSIONS CHART 225
LOTUS 121

www.dba.com.au
GENERAL DISCLAIMER
Important Disclaimer: Certain information in this Catalogue has been compiled from data published by original equipment manufacturers. Disc Brakes Australia Pty Ltd is unable to warrant
the accuracy of third party data, and does not accept responsibility for loss or damage of any kind caused as a result of such data being inaccurate. We also encourage you to contact DBA
if you have any concerns about the information provided. We will make every effort to correct any errors once they are brought to our attention.

Trademarks
DBA, 4000 series, 5000 series Kangaroo Paw, TSP, Thermal Stability Profiling, DBA XS, ALUMALITE logos are either registered or trademarks of Disc Brakes Australia Pty Ltd.

All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of
Disc Brakes Australia Pty Ltd. Trademarks include Part Number identification issued by DISC BRAKES AUSTRALIA PTY LTD.
COPYRIGHT © DISC BRAKES AUSTRALIA
This work is copyright. You may display this material in unaltered form only (retaining this notice) for your use within your organisation. All other rights are reserved. Requests and inquiries
concerning reproduction and rights should be addressed to DBA - PO Box 6666, Silverwater DC, NSW, 1811, Australia; or by e-mail [email protected]

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
ALFA ROMEO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ALfa giulia
1300 1968 - 72 F 353 3 Solid 267 70 10.9 10 82 4
1300 Ti 1968 - 71
PART NOT AVAILABLE
Giulia Super 1971 - 72
REFERENCE ONLY Stud Lengths
Giulia GT Junior 1968 - 73 may vary
Giulia 1600 GT Coupe 1972 - 74
Giulia (Dunlop Brakes) 1964 - 69 F 360 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 286 55.5 10 9 87 4
1300
Berlina ( Ti & Super ) 1966 - 73 R 354 3
PART NOT AVAILABLE
Solid 267 64 9.4 7.5 70 4
REFERENCE ONLY
GT, GTA Junior Coupe
Spider Junior
1600
Berlina ( Ti & Super ) 1966 - 72 R 354 3
PART NOT AVAILABLE
Solid 267 64 9.4 7.5 70 4
REFERENCE ONLY
GTV 1966 - 68
Spider Roadster

GIULIETTA
1800 1980 - 83 F 367 3 Solid 250 54.5 12.6 10.7 72 4
2000 1984 - 86 F 366 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 261 51.5 12.7 10 72 4
1800 1980 - 86 R 365 3
PART NOT AVAILABLE
Solid 250 21 10 8 62 6
REFERENCE ONLY
2000 8mm Stud Hole

GTV
PART NOT AVAILABLE
2 Door Coupe 2.0 Litre 6/98 - on F 763 3 Vented 284
REFERENCE ONLY 40 22 20.2 59 5
R 779 3 Solid 240 40 11 9.2 59 5
V6 2 Door Coupe 3.0 Litre 6/98 - on F 769 3 3 Vented 305 45 28 26 59 5
( Brembo Calipers ) R 779 3 Solid 240 40 11 9.2 59 5

ALFA 1750
Berlina, GTV Coupe 1968 - 72 F 357 3
PART NOT AVAILABLE Solid 272 68 12.5 11.5 82 4
REFERENCE ONLY
Spider Roadster
Berlina, GTV Coupe 1968 - 72 R 354 3
PART NOT AVAILABLE
Solid 267 64 9.4 7.5 70 4
REFERENCE ONLY
Spider Roadster

ALFA 2000
Berlina, GTV Coupe 1972 - 76 F 358 3
PART NOT AVAILABLE Solid 272 68 12.6 10.7 82 4
REFERENCE ONLY
Spider Roadster
Berlina, GTV Coupe 1972 - 76 R 354 3
PART NOT AVAILABLE
Solid 267 64 9.4 7.5 70 4
REFERENCE ONLY
Spider Roadster

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 17
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ALFA 33
All Models 1983 - 85 F 368 3 Solid 239 45 11 9 58 4
1.5 1986 - 88 F 658 3 Solid 239 45 12.7 9 58 4
1.7 Sprint, Ti, iE 1987 - 92 F 369 3 Vented 239 46 22 20.2 58 4

ALFA 75
2.0 TS, 2.5 V6, 3.0 V6 1986 - 92 F 668 3 Vented 268 51.5 22 20 72 5
R 667 3 Solid 250 21 9.9 8 62 6

ALFA 90
2.5 V6 Sedan 1985 - 88 F 668 3 Vented 268 51.5 22 20 72 5

ALFA 147 GTA

V6 DOHC 2D Hatchback 7/2003 - on F 769 3 3 Vented 305 45 28 26 59 5

ALFA 155
2.0i Turbo 16V Q4 1992 - 97 F 665 3 3 Vented 284 44 22 20.2 59 4
2.5 V6 2.5 Turbodiesel
R 666 3 Solid 251 50.5 10 9 59 4

ALFA 156
1.8L 1997 - on F 763 3 Vented 284 40 22 20.2 59 5
2.0i 16V Twin Spark 1997 - on F 356 3 3 Vented 284 44 22 20.2 59 5
2.5i V6 24V
Turbodiesel 2.4 JTD R 359 3 Solid 251 50.5 10 9 59 5

ALFA 164
2.0i Turbo 2.0i V6 Turbo 1987 - 9/92 F 356 3 3 Vented 284 44 22 20.2 59 5
3.0i V6 Quadrifoglio V6
Turbodiesel 2.5 R 359 3 Solid 251 50.5 10 9 59 5

ALFETTA
1.8 Sedan, 2.0 Sedan 1974 - 80 F 361 3 Solid 261 51 11 9 72 4
GT 1.8 Coupe, GTV 2000
2.0 Sedan 1980 - 85 F 366 3 Solid 261 51.5 12.7 10 72 4
1.8 Sedan, 2.0 Sedan 1974 - 80 R 362 3 Solid 250 21 10 8 62 6
GT 1.8 Coup e, GTV 2000 10mm Stud Hole
1.8 Sedan, 2.0 Sedan, 1979 - 85 R 365 3 Solid 250 21 10 8 62 6
GTV 2500 8mm Stud Hole

18 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
ALFA ROMEO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ALFASUD
1200, 1500, L, Ti, Sprint 1971 - 83 F 363 3 Solid 258 10.5 10 8.8 98 4
Ti, Sprint 1983 - 85 F 669 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 258 16 10 8 62 6
1200, 1500, L, Ti, Sprint 1971 - 83 R 364 3 Solid 233 70 9 7.8 Hub 4

montreal
2.6L V8 DOHC 1970 - 77 F 2360 3 3 Vented 272 58 22 20 82.1 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 19
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
AUDI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

AUDI 80 including FOX

1.5 Litre S, LS Fox 1972 - 7/76 F 242 3 Solid 239 39 10 8 65 4
1.5, 1.6 Litre Fox 9/76 - 79 F 240 3 Solid 239 35.2 12 10 65 4
1.8 Litre CC 1986 - 87 F 241 3 Vented 256 47 22 20 68 4
1.9E, 1.9S 1988 - 92
2.2 Coupe 1982 - 84 F 444 3 Vented 239 38.5 20 18 65 4
1.8 Litre CC 1.9E, 1.9S + V6 1986 - on R 445 3 Solid 245 59 10 8.6 68 4

AUDI 90
2.3 Litre except 20v 1989 - 92 F 241 3 Vented 256 47 22 20 68 4
2.3 Litre 20V (125kW) 1989 - 92 F 2241 Vented 276 51.2 25 23 68 4
PART NOT AVAILABLE
REFERENCE ONLY

all rears R 445 3 Solid 245 59 10 8.6 68 4

AUDI 100
S, LS, GL Automatic 1968 - 74 F 248 3 Solid 291 41.5 10.5 9.5 108 4
S, LS, GL Automatic 1971 - 74 F 249 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 291 37.5 10.5 9 108 4
All Models 1974 - 77 F 440 3 Solid 257 40.5 13 11 68 4
All Models 1974 - 77 F 441 3 Vented 257 39.9 20 19 68 4
5+5 GLE, 5E 1978 - 83 F 247 3 Solid 257 46 13 11 68 4
2.1, 2.2, 2.3 CD 1983 - 91 F 241 3 Vented 256 47 22 20 68 4
R 445 3 Solid 245 59 10 8.6 68 4
2.0 4CYL (74KW) 12/90 - 94 F 805 3 Solid 288 46.2 15 13 68 5
2.4 DIESEL
2.0E 4CYL (85KW)
2.3E 5CYL
2.0E 16V 1992 - 94
2.6E V6 05/92 - 94 F 807 3 Vented 288 46.2 25 23 68 5
2.8E V6 12/90 - 94
All Models inc. Avant 1990 - 94 R 810 3 Solid 245 63.9 10 8 68 5
& Quattro rear

20 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
AUDI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

QUATTRO 80
1.8, 1.9, 2.0 (Except 20V) 1986 - 89 F 241 3 Vented 256 47 22 20 68 4
1.9, 2.0 16V 1986 - 89 R 244 3 Solid 245 39 10 8 68 4
2.3, 20V 1989 - 92 R 445 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 245 59 10 8.6 68 4

QUATTRO 90
All models (Except 2.3L 20V) 1989 - 91 F 241 3 Vented 256 47 22 20 68 4
2.3 Litre 20V (125 kw) 1988 - 92 F 2241 3
PART NOT AVAILABLE
REFERENCE ONLY Vented 276 51.2 25 23 68 4
ALL MODELS 1989 - 91 R 244 3 Solid 245 39 10 8 68 4

QUATTRO 100
2.2. Station Wagon CD 1982 - 88 F 241 3 Vented 256 47 22 20 68 4
2.3 (14”, 15” Wheels) 1988 - 91
2.2, 2.3 (14” Wheels) 1982 - 91 R 445 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 245 59 10 8.6 68 4

A3
1.6 (AEH Engine) 1997 - 4/03 F 800 3 Vented 256 36.7 22 19 65 5
1.8 (AGN Engine) 1997 - 4/03 F 801 3 Vented 280 36.7 22 19 65 5
1.8 Turbo (AGU Engine) 1997 - 4/03 F 802 3 Vented 288 34 25 23 65 5
all models A3 Rear 1997 - 4/03 R 803 3 Solid 232 39.5 9 7 65 5
1.6, 1.6FSi, 1.9TDi 2003 - on F 2812 Vented 280 49 22 19 65 5
2.0FSi, 2.0TDi (140hp) 2003 - on F 2810 Vented 288 49.7 25 22 65 5
2.0TDi Quattro (140hp) 2004 - on R 2811 Solid 255 51.5 10 8 65 5
**Check Dimensions** R 2813 Solid 260 48.5 12 10 65 5
2.0TFSi inc. Quattro 2004 - on F 2806 3 3 Vented 312 49.8 25 22 65 5
2.0TDi (170hp) inc. Quattro 2006 - on R 2807 3 3 Solid 285.6 48.4 11.7 10 65 5
3.2 V6 Quattro 7/03 - on F 2808 3 3 Vented 345 49.8 30 27 65 5
R 2809 3 Vented 310 48.5 22 20 65 5

A4 & A4 QUATTRO
1.6 11/94 - 9/97 F 804 3 Solid 280 46.2 13 11 68 5
1.8 20 Valve (ADR engine) 11/94 - 9/97 F 805 3 Solid 288 46.2 15 13 68 5
up to Ch: 8DV-054-061
1.8 20 Valve (ADR engine) 9/97 - 11/04 F 806 3 Vented 280 46.2 22 20 68 5
from Ch: 8DV-054-062
1.6 with 280, 1.9 TDI 9/97 - 10/04
1.8 Turbo (AEB engine) 11/94 - 7/02 F 807 3 Vented 288 46.2 25 23 68 5
1.6 (288) 12/00 - 10/04
1.9 TDI 1995 - 10/04

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 21
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
AUDI - A6 / A8 C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

A4 & A4 Quattro continued

1.9 Tdi 11/94 - 9/97 F 804 3 Solid 280 46.2 13 11 68 5
V6 2.6 & 2.8 (ABC engine) 11/94 -10/04 F 807 3 Vented 288 46.2 25 23 68 5
V6 2.4 30V Quattro 1997 - 11/00
A4 Rear (Exc. Quattro) Hub 11/94 - 11/00 R 808
3 Solid 245 83.6 10 8 HUB 5
A4 Rear (Quattro) 11/94 - 11/00 R 809 3 Solid 245 48
PART NOT AVAILABLE
REFERENCE ONLY
10 8 68 5
1.8i 20V Turbo 8/02 - 10/04 F 2800 3 3 Vented 312 46.2 25 23 68 5
R 2801 3 Solid 245 39.8 10 8 68 5
*Check Rear Rotor Dimensions* 8/02 - on R 2802 3 Solid 255 40 12 10 68 5
1.6, 1.9 TDi 11/04 - 11/07 F 806 3 Vented 280 46.2 22 20 68 5
R 2801 3 Solid 245 39.8 10 8 68 5
1.8 T, 2.0, 2.0 TDi, 2.5 TDi 11/04 - 11/07 F 807 3 Vented 288 46.2 25 23 68 5
R 2801 3 Solid 245 39.8 10 8 68 5
*Check Rear Rotor Dimensions* R 2802 3 Solid 255 40 12 10 68 5
2.0 TFSi 11/04 - 11/07 F 2800 3 3 Vented 312 46.2 25 23 68 5
R 2802 3 Solid 255 40 12 10 68 5
*Check Rear Rotor Dimensions* R 2825 Solid 288 36 12 10 68 5
2.7 TDi 11/04 - 11/07 F 2800 3 3 Vented 312 46.2 25 23 68 5
1.8 T Quattro, 3.0 Quattro 11/04 - 11/07 F 4575 3 3 Vented 320 45.5 30 28 68 5
*Check Front Rotor Dimensions* R 2825 Solid 288 36 12 10 68 5
3.2 FSi 1/06 - 11/07 F 4575 3 3 Vented 320 45.5 30 28 68 5
3.0 TDi Quattro, 3.2 FSi Quattro 1/06 - 11/07 R 2825 Solid 288 36 12 10 68 5
2.7 TDi 11/04 - 11/07 F 2800 3 3 Vented 312 46.2 25 23 68 5
1.8 T Quattro, 3.0 Quattro 11/04 - 11/07 F 4575 3 3 Vented 320 45.5 30 28 68 5
*Check Front Rotor Dimensions* R 2825 Solid 288 36 12 10 68 5
1.8TFSi, 2.0TDi, 2.0TFSi, 2.7TDi 11/07 - on F 2824 Vented 314 52 25 23 68 5
3.0TDi Quattro, 3.2FSI Quattro 11/07 - on F 2822 Vented 320 52 30 28 68 5
*Check Front Rotor Dimensions* R 2823 Solid 300 36 12 10 68 5

A5 & A5 quattro
1.8TFSi, 2.0TDi, 2.0TFSi, 2.7TDi 6/07 - on F 2824 Vented 314 52 25 23 68 5
3.0TDi Quattro, 3.2FSI Quattro 6/07 - on F 2822 Vented 320 52 30 28 68 5
*Check Front Rotor Dimensions* R 2823 Solid 300 36 12 10 68 5

22 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
AUDI A6 / A8 C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

A6 & A6 QUATTRO
1.8 20 Valve (ABK Engine) 10/95 - 3/97 F 805 3 Solid 288 46.2 15 13 68 5
2.0 16 Valve (ABK Engine)
2.0 E (ABK Engine)
Turbodiesel 1.9 TDI 1995 - 3/97
Turbodiesel 2.5 TDI (85 kW) 6/94 - 3/97
V6 2.6 & 2.8 (ABC Engine) 6/94 - 3/97 F 807 3 Vented 288 46.2 25 23 68 5
Turbodiesel 2.5 TDI (103 kW) 1995 - 3/97
All A6 15” Wheels inc. Quattro 3/97 - 4/04
1.8i 20V inc. Turbo, 2.4i V6 30V 3/97 - 4/04 F 2800 3 3 Vented 312 46.2 25 23 68 5
2.8i V6 30V, 1.9 Tdi,
2.5 V6 Tdi
2.0i 20V 01 - 4/04
All with 16” Wheels inc. Quattro
2.7i V6 30V Turbo 1999 - 4/04 F 4575 3 3 Vented 320 46.2 30 28 68 5
3.0i V6 30V 2001 - 4/04
4.2i V8 40V Quattro 1999 - 4/04

All above A6 / Avant (rear) 6/94 - 4/04 R 810 3 Solid 245 63.9 10 8 68 5
All above A6 Quattro (rear) 6/94 - 3/97

All A6 Quattro (rear) 3/97 - 4/04 R 2803 3 Solid 245 53.8 10 8 68 5

with 15” Wheels

All A6 Quattro 03/97 - 04/04 R 2805 3 Solid 255 47.8 10 8 68 5

with 16” Wheels (rear)

A8
4.2L DOHC V8 quattro 2002 - on F 4242 3 3 Vented 321 59.4 30 28 68 5

ALLROAD
2.7i V6 30V Turbo 2000 - on F 4575 3 3 Vented 320 46.2 30 28 68 5
4.2i V8 40V 2002 - on
Turbodiesel 1.9 TDI 2000 - on
Solid rear disc models 2000 - on R 2805 3 Solid 255 47.8 10 8 68 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 23
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
AUDI - S Series / q series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

RS4
2.7i V6 Biturbo 2001 - 2006 F 52804 3 Vented 360 46.7 32 30.4 68 10

S3 & TT
1.8i 1998 - 2002 F 838 3 3 Vented 312 34.2 25 23 65 5
TT Coupe + Roadster 1999 - on
Front Wheel Drive 2000 - 02 R 803 3 Solid 232 39.5 9 7 65 5
Quattro 1KE solid rear disc 2000 - 02 R 352 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 239 34 9 7 65 5
Quattro 1KF vented rear disc 2000 - 02 R 800 3 Vented 256 36.5 22 20 65 5
3.2 V6 Quattro 7/03 - on F 2808 3 3 Vented 345 49.8 30 27 65 5
R 2809 3 Vented 310 48.5 22 20 65 5

S4
2.7 Twin Turbo 1999 - 04 F 4575 3 3 Vented 320 45.5 30 28 68 5
( DBA 4000 series ) 4569
R 3 Vented 256 48 22 20 68 5
V8 4.2L Quattro 2004 - 08 F 42575 3 Vented 344.5 46.7 30 28 68 5
R 42576 3 Vented 300 36.5 22 20 68 5
3.0 TFSi 1/09 - on F TBA Vented 345 52 30 28 68 5
R 2821 Vented 330 36 22 20 68 5

S5
4.2 FSi V8 1/09 - on F TBA Vented 345 52 30 28 68 5
3.0 TFSi V6 1/09 - on R 2821 Vented 330 36 22 20 68 5

S6
4.2L V8 2002 - on F 4240 3 3 Vented 321 52 30 28 68 5
( DBA 4000 series ) 4241
R 3 Vented 269 54 22 20 68 5

Q5
All Models (320mm Front) 2008 - on F 2822 Vented 320 52 30 28 68 5
All Models (345mm Front) 2008 - on F TBA Vented 345 52 30 28 68 5
All Models (Solid Rear) 2008 - on R 2823 Solid 300 36 12 10 68 5
All Models (Vented Rear) 2008 - on R 2821 Vented 330 36 22 20 68 5

Q7
4.2 FSI Quattro 03/06 - on F 42246 Vented 350 69 34 32 85 5
3.0 TDI Quattro
all models (exc. Brembo caliper) R 42245 Vented 330 74 28 26 85 5
all models (w/Brembo caliper) R 2249 Vented 358 73.5 28 26 85 5
This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish
rotor and also available as a plain standard finish rotor
24 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

1502
PART NOT AVAILABLE
All 1975 - 77 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

1600
PART NOT AVAILABLE
Touring 1971 - 73 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

1600-2
PART NOT AVAILABLE
All 1966 - 71 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

1602
PART NOT AVAILABLE
Touring 1971 - 73 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

1800
PART NOT AVAILABLE
Touring 1971 - 73 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

1802
PART NOT AVAILABLE
Saloon/Touring 1971 - 75 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

2000
PART NOT AVAILABLE
Touring 1969 - 75 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

2002
PART NOT AVAILABLE
(- Ti/Rii/Turbo) 1968 - 75 F 370 3
REFERENCE ONLY Solid 240 58.5 10 8.4 63 4

2500
CS/Automatic 1969 - 77 F 371 3 Solid 272 59.8 12.7 11.4 74 5
R 374 3 Solid 272 61.5 9.5 7.9 75 5

2800
Automatic 3 1969 - 77 F 373 Solid 272 59.8 12.7 11.4 74 5
R 374 3 Solid 272 61.5 9.5 7.9 75 5
CS/Automatic 1970 - 72 F 371 3 Solid 272 59.8 12.7 11.4 74 5

3000
Bavaria/Automatic 1971 - 77 F 371 3 Solid 272 59.8 12.7 11.4 74 5
R 374 3 Solid 272 61.5 9.5 7.9 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 25
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 3 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

1 SERIES
(E87) 120d, 120i 3/03 - 4/07 F 2862 3 Vented 300 73.7 24 22.4 79 5
(E81) 120d, 120i 2/06 - on R TBA
(E82) 120d, 120i, 125i 1/07 - on
(E88) 120d, 120i, 125i 5/07 - on
(E87) 123d, 130i, (E88) 123d 3/05- on F 2860 3 Vented 330 73.2 24 22.4 79 5
(E81) 123d, 130i, (E82) 123d 9/06 - on R TBA

315
(E21) 1981 - 83 F 376 3 Solid 255 75.1 12.5 11.1 63 4

316
(E21) 1975 - 82 F 376 3 Solid 255 75.1 12.5 11.1 63 4

316i
(E30) 1982 - 87 F 678 3 Solid 260 35.1 12.7 11.1 66 4
(E30) including ABS 1982 - 93 F 679 3 Vented 260 35.1 22 20.4 66 4
Touring R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) including ABS 1990 - 2000 F 978 3 Solid 286 51.7 12 10.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5

318i, 318d
(E21) 1975 - 82 F 376 3 Solid 255 75.1 12.5 11.1 63 4
(E30) 1982 - 91 F 678 3 Solid 260 35.1 12.7 11.1 66 4
(E30) including ABS 1982 - 93 F 679 3 Vented 260 35.1 22 20.4 66 4
Touring / Cabriolet R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) including ABS 12/90 - 98 F 978 3 Solid 286 51.7 12 10.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5
(E46) Saloon 4/98 - on F 979 3 Vented 286 51.6 22 20.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5
E90 With option code: S100A 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
E91 2005 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

318iS
(E30) 1989 - 91 F 679 3 Vented 260 35.1 22.5 20.4 66 4
R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) Saloon/Coupe 1992 - 98 F 979 3 Vented 286 51.6 22 20.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5

26 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 3 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

318tds
PART NOT AVAILABLE
(E36) Saloon/Compact 1994 - on F 978 3REFERENCE
ONLY Solid 286 51.7 12 10.4 79 5
(E36) Touring 1994 - on F 978 3 Solid 286 51.7 12 10.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5

318ti
(E36) Compact 1995 - 4/98 F 978 3 3 Solid 286 51.7 12 10.4 79 5
R 981 3 Solid 272 78 10 8.4 75 5

320 / 320-6
(E21) 1975 - 79 F 394 3 Solid 255 75.1 12.5 11.1 63 4

320d
(E46) Saloon 4/98 - on F 979 3 Vented 286 51.6 22 20.4 79 5
R 980 3
PART NOT AVAILABLE
Vented 276
REFERENCE ONLY 60 19 17.4 75 5
E90 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R TBA Vented 300 20
E91 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5
E90, E91 2004 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
With option code: S102A R 2859 3 3 Vented 336 67.2 22 20.4 75 5

320i : iS
(E21) 1975 - 78 F 378 3 Vented 255 75.1 22 20.4 63 4
(E21) USA 9/77 - 83 F 376 3 Solid 255 75.1 12.5 11.1 63 4
(E30) 1982 - 91 F 679 3 Vented 260 35.1 22 20.4 66 4
incl. Touring / Cabriolet R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) 12/90 - 98 F 979 3 Vented 286 51.6 22 20.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5
(E46) Saloon 4/98 - on F 979 3 Vented 286 51.6 22 20.4 79 5
R 980 3 Vented 276 60 19 17.4 75 5
E90 2004 - on F TBA Vented 292 22
R TBA Solid 296 10
E90 With option code: S100A 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R TBA Vented 300 20
E91 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

320si
E90 2005 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 27
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 3 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

323i
E90, E92 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
2006 - on R TBA 3 Vented 300 20
E91 2005 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

323id
(E21) 1978 - 82 F 378 PART NOT AVAILABLE
3 Vented 255
REFERENCE ONLY 75.1 22 20.4 63 4
671 R 3 Solid 258 60.1 10 8.4 62 4
(E30) 1981 - 86 F 679 3 Vented 260 35.1 22 20.4 66 4
R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) 1995 - 99 F 979 3 Vented 286 51.6 22 20.4 79 5
R 980 3 Vented 276 60.1 19 17.4 75 5
(E46) Saloon 4/98 - on F 979 3 Vented 286 51.6 22 20.4 79 5
(E46) Coupe 1999- on
R 980 3 Vented 276 60 19 17.4 75 5

324d : td
(E30) 1987 - 91 F 679 3 Vented 260 35.1 22 20.4 66 4
R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) Touring 1988 - 93 F 679 3 Vented 260 35.1 22 20.4 66 4
R 671 3 Solid 258 60.1 10 8.4 62 4

28 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 3 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

325i : 325ix : 325ci

(E30) 1989 - 91 F 679 3 Vented 260 35.1 22 20.4 66 4
R 671 3 Solid 258 60.1 10 8.4 62 4
(E36) 12/90 - 99 F 979 3 Vented 286 51.6 22 20.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5
(E46) Saloon/Touring 2000 - on F 966 3 Vented 300 52 22 20 79 5
R 967 3 Vented 294 59.5 19 17.4 75 5
E90 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
E92 With option code: S212A 2005 - on
R TBA Vented 300 20
E91 2004 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5
E90, E91 2004 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
With option code: S100A R 2859 3 3 Vented 336 67.2 22 20.4 75 5
E92 2005 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
R TBA Vented 300 20

325d
E90, E91 2006 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
R 2859 3 3 Vented 336 67.2 22 20.4 75 5

325xi
E90 2006 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5
E90 With S100A option 2006 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
R 2859 3 3 Vented 336 67.2 22 20.4 75 5
E91 U.S. Model 2006 - on F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5
E91 Euro Model 2005 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
R 2859 3 3 Vented 336 67.2 22 20.4 75 5
E92 Euro Model 2005 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 29
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 3 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

325td : tds
(E36), (E36) Touring 9/91 - 1999 F 979 3 Vented 286 51.6 22 20.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5

328i : 328ci
(E36) Coupe 11/94 - 99 F 979 3 Vented 286 51.6 22 20.4 79 5
R 980 3 Vented 276 60.1 19 17.4 75 5
(E36) Saloon/Cabriolet 11/94 - 99 F 979 3 Vented 286 51.6 22 20.4 79 5
R 983 3 Solid 280 60.1 10 8.4 75 5
(E36) Saloon Cabriolet 11/94 - on R 980 3 Vented 276 60.1 19 17.4 75 5
(German Application)
(E36) Touring 11/94 - 99 F 979 3 Vented 286 51.6 22 20.4 79 5
R 980 3 Vented 276 60.1 19 17.4 75 5
(E46) 4/98 - on F 966 3 Vented 300 52 22 20 79 5
R 967 3 Vented 294 59.5 19 17.4 75 5
E90 2006 - ON F 2862 3 Vented 300 73.7 24 22.4 79 5
E92 2005 - ON
R TBA Vented 300 20
E91 U.S. Model 2004 - ON F 2862 3 Vented 300 73.7 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

328xi
E90, E91, E92 2005 - ON F 2862 3 Vented 300 73.7 24 22.4 79 5
All U.S. Models
R 2861 3 Vented 300 66 20 18.4 75 5

330
(E46) 7/00 - 05 F 2855 3 Vented 324 52 25 23.4 79 5
R 2856 3 Vented 320 60.8 22 20.4 75 5

30 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 3 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

330d : 330i : 330xd : 330xi

With option code; 12/06 - on F 2858 3 3 3 Vented 348 73.2 30 28.4 79 5
S100A /S102A 2859 3 3 Vented 336 67.2
R 22 20.4 75 5
E90 Saloon
E91 Touring
E92 Coupe

330cd : 330ci : 330i : 330d : 330xd : 330xi

(E46) 7/00 - 05 F 2855 3 Vented 324 52 25 23.4 79 5
R 2856 3 3 Vented 320 60.8 22 20.4 75 5

335d : 335i
E90 Saloon 2006 - on F 2858 3 3 3 Vented 348 73.2 30 28.4 79 5
2859 3 3 Vented 336 67.2 22 20.4
E91 Touring R 75 5
E92 Coupe

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 31
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 5 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

518
(E12) 1974 - 2/76 F 373 3 Solid 272 59.8 12.7 11.4 74 5
(E12) 3/76 - 81 F 377 3 Solid 280 78.1 12.7 11.1 74 5
(E12) vented discs 8/76 - 81 F 379 3 Vented 280 78.1 22 20.4 74 5
PART NOT AVAILABLE
REFERENCE ONLY

518i
(E28) 1981 - 88 F 672 3 Solid 284 76.1 12 10.4 79 5
(E30) Touring 1981 - 88 F 675 3 Vented 284 76.1 22 20.4 79 5
R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5

518i
(E34) including ABS 1989 - 1996 F 975 3 Solid 302 76.1 12 10.4 79 5
incl. Touring R 976 3 Solid 300 61.1 10 8.4 75 5

520-6
(E12) 1977 - 81 F 377 3 Solid 280 78.1 12.7 11.4 74 5
(E12) vented discs 1977 - 81 F 379 3
PART NOT AVAILABLE
Vented 280
REFERENCE ONLY 78.1 22 20.4 74 5

520i
(E12) 1972 - 2/76 F 373 3 Solid 272 59.8 12.7 11.4 74 5
(E12) 3/76 - 79 F 377 3 Solid 280 78.1 12.7 11.1 74 5
(E12) vented discs 1976 - 79 F 379 3 Vented 280 78.1 22 20.4
PART NOT AVAILABLE
REFERENCE ONLY 74 5

520i
(E28) 1980 - 8/84 F 672 3 Solid 284 76.1 12 10.4 79 5
(E28) + ABS 1980 - 87 F 675 3 Vented 284 76.1 22 20.4 79 5
R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5
(E34) Sedans 1987 - 95 F 975 3 Solid 302 76.1 12 10.4 79 5
(E34) Wagons + Touring 24V 1989 - 95 F 974 3 Vented 302 76.1 22 20.4 79 5
(E34) All Models (Rear) R 976 3 Solid 300 61.1 10 8.4 75 5
(E39) 1996 - 03 F 986 3 Vented 296 76 22 20.4 79 5
R 987 3 Solid 298 61 10 8.4 75 5

523i
(E39) 1995 - 2000 F 986 3 Vented 296 76 22 20.4 79 5
Saloon solid rear disc R 987 3 Solid 298 61 10 8.4 75 5
Saloon vented rear R 989 3 Vented 298 61
PART NOT AVAILABLE
20 18.4 75 5
REFERENCE ONLY
+ all TOURING models

32 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 5 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

524d
(E28) 1986 - 87 F 675 3 Vented 284 76.1 22 20.4 79 5
R 670 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 284 61.1 10 8.4 75 5

524td
(E28) 10/82 -8/84 F 672 3 Solid 284 76.1 12 10.4 79 5
(E28) + ABS 10/82 -1987 F 675 3 Vented 284 76.1 22 20.4 79 5
R 670 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 284 61.1 10 8.4 75 5
(E34) 1987 - 92 F 975 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 302 76.1 12 10.4 79 5
R 976 3 Solid 300 61.1 10 8.4 75 5

525
(E12) solid front disc 1973 - 2/76 F 373 3 Solid 272 59.8 12.7 11.4 74 5
(E12) solid front disc 2/76 - 81 F 377 3 Solid 280 78.1 12.7 11.1 74 5
(E12) vented front disc 1976 - 81 F 379 3 Vented 280 78.1 22 20.4
PART NOT AVAILABLE
REFERENCE ONLY 74 5
rear suits all models above 1973 - 81 R 374 3 Solid 280 61.1 9.5 7.9 75 5

525e/i
(E28) 1981 - 87 F 675 3 Vented 284 76.1 22 20.4 79 5
R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5

525i
(E34) 1987 - 90 F 974 3 Vented 302 76.1 22 20.4 79 5
R 976 3 Solid 300 61.1 10 8.4 75 5

525i 24V
(E34) 8/90 - 96 F 974 3 Vented 302 76.4 22 20.4 79 5
incl. Touring R 976 3 Solid 300 61.1 10 8.4 75 5

525td : tds
(E34) 1990 - 95 F 975 3 Solid 302 76.1 12 10.4 79 5
R 976 3 Solid 300 61.1 10 8.4 75 5
(E34) Touring 7/91 - 96 F 974 3 Vented 302 76.1 22 20.4 79 5
R 976 3 Solid 300 61.1 10 8.4 75 5
(E39) 1996 - 2000 F 986 3 Vented 296 76 22 20.4 79 5
R 987 3 Solid 298 61 10 8.4 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 33
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 5 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

528
(E12) 1975 - 1/76 F 373 3 Solid 272 59.8 12.7 11.4 74 5
(E12) 2/76 - 7/76 F 377 3 Solid 280 78.1 12.7 11.1 74 5
(E12) 8/76 - 77 F 379 3 Vented 280 78.1 22 20.4
PART NOT AVAILABLE
REFERENCE ONLY 74 5
(E12) ( Rear ) 1975 - 77 R 374 3 Solid 272 61.5 9.5 7.9 75 5

528i
PART NOT AVAILABLE
(E12) 1977 - 6/81 F 379 3 Vented 280
REFERENCE ONLY 78.1 22 20.4 74 5
R 374 3 Solid 272 61.5 9.5 7.9 75 5
(E28) 1981 - 5/84 F 675 3 Vented 284 76.1 22 20.4 79 5
(E28) 6/84 - 87 F 970 3 Vented 282 76.1 25 23 79 5
1981 - 87 R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5

528i 24V
(E39) 2.8 1996 - 2000 F 986 3 Vented 296 76 22 20.4 79 5
R 989 3 Vented 298 61
PART NOT AVAILABLE
REFERENCE ONLY 20 18.4 75 5

530i
(E34) 1988 - 96 F 974 3 Vented 302 76.1 22 20.4 79 5
R 976 3 Solid 300 61.1 10 8.4 75 5
(E39) 1999 - 03 F 2854 3 Vented 324 73.5 30 28.4 79 5
R 989 3 Vented 298 61
PART NOT AVAILABLE
REFERENCE ONLY 20 18.4 75 5
(E60) 2001 - on F 2868 Vented 324 77.5 30 28.4 79 5
R 2869 Vented 320 63 20 18.4 75 5

535i
(E28) 1985 - 87 F 970 3 Vented 282 76.1 25 23 78 5
R 670 3 Solid 284 61.1 10 8.4 75 5
PART NOT AVAILABLE
REFERENCE ONLY

(E34) 1988 - 95 F 974 3 Vented 302 76.1 22 20.4 79 5

R 976 3 Solid 300 61.1 10 8.4 75 5
(E39) 1995 - 9/97 F 986 3 Vented 296 76 22 20.4 79 5
R 989 3 Vented 298 61
PART NOT AVAILABLE
REFERENCE ONLY
20 18.4 75 5
(E39) 9/97 - 3/00 F 988 3 Vented 324 77.1 30 28.4 79 5
R 989 3 Vented 298
PART NOT AVAILABLE
REFERENCE ONLY 61 20 18.4 75 5
(E39) V8 3/2000 - on F 2854 3 Vented 324 73.5 30 28.4 79 5
R 989 3 Vented 298
PART NOT AVAILABLE
REFERENCE ONLY 61 20 18.4 75 5

34 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 5 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

540 / 540i
(E34) Saloon 10/92 - 95 F 971 3 Vented 302 76.1 28 26.4 79 5
(E34) Touring 10/92 - 97 F 971 3 Vented 302 76.1 28 26.4 79 5
R 969 3 Vented 300 61.1 20 18.4
PART NOT AVAILABLE
REFERENCE ONLY 75 5
(E39) 4.4 V8 1995 - 3/00 F 988 3 Vented 324 77.1 30 28.4 79 5
R 989 3
PART NOT AVAILABLE
Vented 298
REFERENCE ONLY 61 20 18.4 75 5
(E39) V8 3/2000 - 03 F 2854 3 Vented 324 73.5 30 28.4 79 5
R 989 3 Vented 298 61
PART NOT AVAILABLE
REFERENCE ONLY 20 18.4 75 5

bmw - 6 series
628
PART NOT AVAILABLE
(E24) CSi 1979 - 4/82 F 379 3
REFERENCE Vented 280
ONLY 78.1 22 20.4 74 5
(E24) CSi 5/82 - 87 F 970 3
PART NOT AVAILABLE
REFERENCE Vented 282
ONLY 76.1 25 23 79 5
R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5

630
PART NOT AVAILABLE
(E24) CSi 1976 - 79 F 379 3
REFERENCE Vented 280
ONLY 78.1 22 20.4 74 5
R 673 3
PART NOT AVAILABLE
REFERENCE ONLY Vented 272 68.5 19 17 75 5

633
PART NOT AVAILABLE
(E24) CSi 1976 - 4/82 F 379 3
REFERENCE Vented 280
ONLY 78.1 22 20.4 74 5
R 673 3
PART NOT AVAILABLE
REFERENCE Vented 272
ONLY 68.5 19 17 75 5

635
PART NOT AVAILABLE
(E24) CSi 1978 - 4/82 F 379 3
REFERENCE Vented 280
ONLY 78.1 22 20.4 74 5
R 673 3
PART NOT AVAILABLE
REFERENCE ONLY Vented 272 68.5 19 17 75 5
(E24) CSi 5/82 - 89 F 970 3 Vented 282 76.1 25 23 79 5
R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 35
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
bmw - 7 series C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

728i : 728ia
(E23) 1977 - 8/82 F 379 3
PART NOT AVAILABLE
Vented 280
REFERENCE ONLY 78.1 22 20.4 74 5
R 676 3 Solid 280 68.1 10 8.4 75 5
(E23) 9/82 - 86 F 677 3 Vented 280 78.1 25 23.4 74 5
R 674 3 Solid 284 68.1 10 8.4 75 5
(E38) 1995 - 10/01 F 990 3 Vented 316 77 28 26 79 5
R 991 3 Solid 324 61 12 10 75 5

730 : 730i : 730iL

(E23) 1977 - 79 F 379 3 Vented 280 78.1 22 20.4 74 5
PART NOT AVAILABLE
REFERENCE ONLY

R 676 3 Solid 280 68.1 10 8.4 75 5

(E32) 6 cyl & V8 11/87 - 6/94 F 974 3 Vented 302 76.1 22 20.4 79 5
1987 - 1993 R 972 3 Solid 300 68.5 12 10.4 75 5
PART NOT AVAILABLE
REFERENCE ONLY

1993 - 1994 R 977 3 Solid 300 68.1 10 8.4 75 5

PART NOT AVAILABLE
REFERENCE ONLY

(E38) 1994 - 2000 F 990 3 Vented 316 77 28 26 79 5

R 991 3 Solid 324 61 12 10 75 5

732i : 733i
(E23) 1977 - 86 F 379 3 Vented 280 78.1 22 20.4 74 5
PART NOT AVAILABLE
REFERENCE ONLY

(E23) 1979 - 8/81 R 676 3 Solid 280 61.1 10 8.4 75 5

(E23) 9/81 - 86 R 674 3 Solid 284 68.1 10 8.4 75 5

735i : iL
(E23) 1979 - 8/81 F 379 3 Vented 280 78.1 22 20.4 74 5
PART NOT AVAILABLE
REFERENCE ONLY

R 676 3 Solid 280 68.1 10 8.4 75 5

(E23) 9/81 - 86 F 677 3 Vented 280 78.1 25 23.4 74 5
R 674 3 Solid 284 68.1 10 8.4 75 5
(E32) 1986 - 1992 F 971 3 Vented 302 76.1 28 26.4 79 5
R 972 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 300 68.1 12 10.4 75 5
(E38) 1994 - 2000 F 990 3 Vented 316 77 28 26 79 5
R 991 3 Solid 324 61 12 10 75 5

740i : iL
(E32) 1992 - 6/94 F 971 3 Vented 302 76.1 28 26.4 79 5
(E32) R 2852 3 Vented 300 68.5 20 18.4 75 5
(E38) 1995 - 01 F 988 3 Vented 324 77.1 30 28.4 79 5
R 991 3 Solid 324 61 12 10 75 5

36 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - 7 / 8 / M SERIES C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

745i
(E23) 1980 - 86 F 677 3 Vented 280 78.1 25 23.4 74 5
(E23) 1980 - 8/81 R 676 3 Solid 280 68.1 10 8.4 75 5
(E23) 9/81 - 86 R 674 3 Solid 284 68.1 10 8.4 75 5

750i : iL
(E32) 87 - 89 F 971 3 Vented 302 76.1 28 26.4 79 5
(E32) + floating caliper 90 - 6/94
(E32) 87 - 6/94 R 2852 3 Vented 300 68.5 20 18.4 75 5
(E38) 750i V12 5.4L 240kW 6/94 - 10/01 F 2670 3 Vented 334 77 32 30 79 5
R 2671 3 Vented 328 61 20 18.4 75 5

840i, 840 Ci
E31 12/92 - 5/99 F 988 3 Vented 324 77.1 30 28.4 79 5
R 991 3 Solid 324 61 12 10 75 5

850 Ci
E31 (M70) 7/89 - 10/94 F 988 3 Vented 324 77.1 30 28.4 79 5
R 991 3 Solid 324 61 12 10 75 5

m3
(E36) 3.0i 24V 1992 - 1995 F 984 3 3 Vented 315 52.5 28 26.4 79 5
(E36) 3.2i 24V 1995 - 2001
R 985A 3 LH Vented 312 61 19.9 18.4 79 5
R 985B 3 RH Vented 312 61 19.9 18.4 79 5

(E46) 2001 - on F 42850 3 Vented 325 52.5 28 26.4 79 5

F 52880 3 Vented 325 52.5 28 26.4 79 5
R 42851 3 Vented 327 61 20 18.4 75 5

M5
PART NOT AVAILABLE
(E34) 3.5i 24V 1988 -1996 F 968 3
REFERENCE Vented 315
ONLY 76 28 26.4 79 5
R 969 3
PART NOT AVAILABLE
Vented 300
REFERENCE ONLY 61.1 20 18.4 75 5

m535i
(E28) 1985 - 87 F 970 3 Vented 282 76.1 25 23 79 5
R 670 3
PART NOT AVAILABLE
REFERENCE
ONLY Solid 284 61.1 10 8.4 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 37
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW - Z / X SERIES C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

z3
1.8i Roadster 1996 - 03 F 978 3 Solid 286 51.7 12 10.4 79 5
1.9i 16V Roadster 1996 - 99
2.0i 24V Roadster 1999 - 00
2.0i, 2.2i, 2.8 Coupe/Roadster 1999 - 03 F 979 3 3 Vented 286 51.6 22 20.4 79 5
3.0i - Except M-Series 1999 - on F 966 3 3 Vented 300 52 22 20 79 5
All models except M Series 1996 - 03 R 982 3 Solid 272 83.4 10 8.4 75 5
M-Series 1997 - 03 F 984 3 3 Vented 315 52.5 28 26.4 79 5
R 985A 3 LH Vented 312 61 19.9 18.4 79 5

R 985B 3 RH Vented 312 61 19.9 18.4 79 5

Z4
2.5i 24V 2003 - on F 979 3 3 Vented 286 51.6 22 20.4 79 5
3.0i 24V 2003 - on F 966 3 3 Vented 300 52 22 20 79 5

x1 (4 WD)
(E84) xDrive 2.3d 9/09 - on F 2860 3 Vented 330 73.2 24 22.4 79 5
R 2861 3 Vented 300 66 20 18.4 75 5

X3 (4 WD)
(E83) 2.0d 16V, 2.5i 24V 2004 - on F 2876 3 Vented 325 62 25 23.4 75 5
(E83) 3.0i 24V, 2.0i R 2875 3 Vented 320 68 22 20.4 75 5
(E83) 3.0 Twin TD 3/07 - on F 2876 3 Vented 325 62 25 23.4 75 5
**Check Dimensions** F 813 3 Vented 332 62 30 28.4 75 5
R 814 3 Vented 324 80 12 10.4 75 5

X5 (4 WD)
(E53) 3.0i, 3.0d 24V, 4.4i V8 2001 - 2/07 F 813 3 Vented 332 62 30 28.4 75 5
R 814 3 Solid 324 80 12 10.4 75 5
(E53) 4.6iS 4 Door Wagon 2001 - 03 F 823 3 Vented 356 62 36 34.4 75 5
4.8iS 2003 - 2/07 R 824 3 Vented 324 80 20 18.4 75 5
(E70) 3.0si 2/07 - 8/08 F 2864 3 Vented 348 62 30 28.4 75 5
(E70) xDrive 3.0i 9/08 - on F 2874 3 Vented 332 62 30 28.4 75 5
**Check Dimensions** R 2865 Vented 320 78 20 18.4 75 5
(E70) 4.8i 2/07 - 8/08 F 2864 3 Vented 348 62 30 28.4 75 5
(E70) xDrive 4.8i 9/08 - on F TBA Vented 365 36
**Check Dimensions** R 2867 3 Vented 345 78 24 22.4 75 5
(E70) 3.0d 2/07 - 8/08 F 2864 3 Vented 348 62 30 28.4 75 5
(E70) xDrive 3.0d 9/08 - on R 2865 Vented 320 78 20 18.4 75 5

38 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
BMW X SERIES C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

X5 (4 WD) - continued
(E70) 3.0sd 2/07 - 8/08 Vented 365
F TBA 36
(E70) xDrive 3.5d 9/08 - on R 2867 3 Vented 345 78 24 22.4 75 5

X6 (4 WD)
(E71) 3.0d 5/08 - 8/08 F 2864 3 Vented 348 62 30 28.4 75 5
(E71) xDrive 3.0d 9/08 - on R 2865
Vented 320 78 20 18.4 75 5
(E71) 3.5i, 3.5d 5/08 - 8/08 F TBA Vented 365 36
(E71) xDrive 3.5, xDrive3.5d 9/08 - on R 2867 3 Vented 345 78 24 22.4 75 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 39
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
chevrolet C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

astro van
2WD & 4WD 2003 - 2005 F 2000 Vented 305 61 29 27.2 79 6

camaro
All models 1998 - 2002 F 2996 3 3 Vented 303 52.5 32 30.7 71 5
R 2997 3 3 Vented 305 62 26 24.7 71 5
V6 2010 - on F 2602 Vented 321 51.3 30 27 67.4 5
R 2603 Vented 315 48 23 21 67.4 5
V8 2010 - on F 2604 3 3 3 Vented 355 50 32 30 67.4 5
R 2605 3 3 Vented 365 47.7 28 26 67.4 5

COBALT
SS 2.0L Coupe 2005 - on F 2052 3 3 Vented 296 43 26 23 66 5
R 2053 3 3 Solid 270 45 14 12 66 5

CORVETTE
C4 - 12 inch 1988 - 96 F 999 3 Vented 304.8 56 20.5 19 71 5
( curved vane left & right handed ) R 997 3 Vented 304.8 50.4 20.5 19 71 5
C4 - 13 inch 1988 - 96 F 996 3 3 Vented 330 56 28 26.5 71 5
( curved vane REAR left & right handed ) R 997 3 Vented 304.8 50.4 20.5 19 71 5
C5 1997 - 03 F 067 3 3 3 Vented 325 46 32 30.3 71 5
(DBA067 interchangeable with DBA2994) R 2995 3 3 Vented 305 49 26 24 70.5 5
C6 2005 - on F 2994 3 3 3 Vented 325 45 32 30 70.5 5
R 2995 3 3 Vented 305 49 26 24 70.5 5
C6 Z-51 2005 - on F 2990 3 3 3 Vented 340 45 32 30 70.5 5
( performance package ) R 2991 3 3 Vented 330 49 26 24 70.5 5
C6 Z06 2005 - on F 2992 3 3 3 Vented 355 45.5 32 30 70.7 5
R 2993 3 3 Vented 340 49.7 26 24 70.7 5

IMPALA
All Models 2005 - 08 F 2606 3 3 Vented 303 52 30 28 70.7 5
R 2607 3 3 Solid 278 51 11 9 70.7 5

40 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
chevrolet TRUCKS/SUV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

avalanche 1500
2000
w/o Ltd. Slip Axel 2002 F Vented 305 61 29 27.2 79 6
18.5mm min. thick. rear
w/ Ltd. Slip Axel 2002 - 2006 F 2000 Vented 305 61 29 27.2 79 6
28.5mm min. thick rear disc
R 2001 Vented 330 97 30 28.5 76 6
w/18.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 30 27.2 76 6

AVALANCHE 2500
exc. factory 2” body lift 2002 F 2048 Vented 325 89.5 38 36.5 118.2 8
2049
R Vented 330 85.6 29 26.5 118.2 8
exc. factory 2” body lift 2003 - 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8

BlaZER
ALL 1992 - 1994 F 773 Vented 325 89.5 38 36.5 118.2 8

EXPRESS 1500 VAN

1/2 Ton 2003 - 2006 F 2000 Vented 305 61 29 27.2 79 6

EXPRESS 2500 VAN

3/4 Ton - 7300lb GVW 2003 - 2006 F 2000 Vented 305 61 29 27.2 79 6
2001
6 lug R Vented 330 97 30 28.5 76 6
3/4 Ton - 8500-8600 GVW 2003 - 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8
pass./panel (8 lug)
R 2049 Vented 330 85.6 29 26.5 118.2

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is
available under its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available
as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 41
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter

chevrolet C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SILVERADO 1500 1/2 TON 2WD

1/2 Ton - ex. std. cab & std. 1988 - 1991 F 773 Vented 295 63.5 32.5 30.8 79 6
1/2 Ton 1992 - 1999 F 773 Vented 295 63.5 32.5 30.8 79 6
3/4 Ton - 7200 lb. GVW, 1988 - 1998 F 773 Vented 295 63.5 32.5 30.8 79 6
6 lug
w/ rear disc, exc. HD 1999 - 2000 F 2000 Vented 305 61 29 27.2 79 6
4 dr. HD - 4.63” rear disc 2000 - 2001 F 2048 Vented 325 89.5 38 36.5 118.2 8
hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr 2001 - 2002 F 2000 Vented 305 61 29 27.2 79 6
4 dr HD - crew cab 2001 F 2048 Vented 325 89.5 38 36.5 118.2 8
(8 lug front)
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. - ext. cab- Quadrasteer 2002 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD - crew cab 2002 F 2048 Vented 325 89.5 38 36.5 118.2 8
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. - reg. & ext. cab- 2003 F 2000 Vented 305 61 29 27.2 79 6
2 wh. steer
2 dr. - ext. cab - Quadrasteer 2003 F 2000 Vented 305 61 29 27.2 79 6
w/ 18.5mm min, thick rear discs
2 dr. ext. cab quadrasteer 2003 F 2000 Vented 305 61 29 27.2 79 6
w/ 28.5mm min, thick rear discs
2 dr. reg. & ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
2 wh. steer
2 dr. - ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
hybrid and quadrasteer models
R 2001 Vented 330 97 30 28.5 76 6
2 dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.63” read disc hub hole
2 dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.84” rear disc hub hole
4 dr. HD - crew cab 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc, 2 wh. steer & quadrasteer

4 dr. HD - crew cab 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & 2 wh. Steer (8 lug front)

42 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
chevrolet C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SILVERADO 1500 1/2 TON 4WD

w/ rear disc 1999 - 2000 F 2000 Vented 305 61 29 27.2 79 6
2 dr. - reg. cab 2001 F 2000 Vented 305 61 29 27.2 79 6
2 dr. - ext. cab 2001 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD 2001 F 2048 Vented 325 89.5 38 36.5 118.2 8
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. 2002 F 2000 Vented 305 61 29 27.2 79 6
2 dr. ext. cab quadrasteer 2002 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD crew cab 2002 F 2048 Vented 325 89.5 38 36.5 118.2 8
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. ext. cab - SS 2003 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD - crew cab 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
- 2 wh. steer
R 2049 Vented 330 85.6 29 26.5 118.2 8
4 dr. Hd - crew cab 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
Quadrasteer
2 dr. - reg. & ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
2 wh. steer
2 dr. - reg. & ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
Quadrasteer
2 dr. - ext. cab - SS 2004 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
2 Dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.84” rear disc hub hole
4 dr. - crew cab - std. duty 2004 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
2 dr. - ext. cab - SS 2005 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 43
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter

chevrolet C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SILVERADO 1500 1/2 TON 4WD continued

4 dr. HD - crew cab 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & 2 wh. steer
4 dr. HD - crew cab, 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & quadrateer
4 dr. HD - crew cab 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & 2 wh. steer (8 lug front)

SILVERADO 2500 3/4 TON 2WD

exc. 6.0L, w/ 5-speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
6.0L w/ 5-speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84 rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
exc. HD - w/ A/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD - w/ M/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
exc. HD - w/ A/T 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD - w/ M/T 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
HD - 2 wh. steer 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
exc. HD 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
exc. HD 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8

SILVERADO 2500 3/4 TON 4WD

exc. 6.0L, w/ 5 speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
6.0L w/ 5-speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8

44 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter

chevrolet C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SILVERADO 2500 3/4 TON 4WD continued

exc. HD w/ A/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
exc. HD w/ A/T 2004
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD w/ M/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
exc. HD w/ M/T 2004
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122
HD - 2 wh. steer 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
exc. HD 2005
exc. HD 2006

Suburban 1500 1/2 Ton 2wd

w/28.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 29 27.2 79 6
all models 2003 - on R 2001 Vented 330 97 30 28.5 76 6

Suburban 1500 1/2 ton 4wd

6 lug 1992 - 1999 F 773 Vented 295 63.5 32.5 30.8 79 6
w/28.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 29 27.2 79 6
all models 2003 - on
R 2001 Vented 330 97 30 28.5 76 6
w/18.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 30 27.2 76 6

Suburban 2500 3/4 Ton 2wd & 4WD

2 wh. steer - 4.63” 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
2049
R Vented 330 85.6 29 26.5 118.2 8
2 wh. steer - 4.84” 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
Quadrasteer 2000 - 2005
all models 2006 - on

TAHOE
all models 2000 - 2006 F 2000 Vented 305 61 29 27.2 79 6
2001
R Vented 330 97 30 28.5 76 6
all models 2008 - on F 2010 Vented 330 55.7 30 28 78.6 6
2011
R Vented 345 85.3 20 18.5 78.6 6

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 45
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CHRYSLER / DODGE C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

300C + DODGE charger

3.5L V6 2WD & 4WD 2005 - on F 2438 3 3 Vented 345 55.1 28 26.5 72.6 5
5.7L Hemi V8 2WD & 4WD R 2439 3 3 Vented 320 67.3 22 20.5 72.6 5
5.7L V8 SRT8 2WD & 4WD 2005 - on F 2444 3 3 Vented 360 58.5 32 30 72.5 5
R 2445 3 3 Vented 350 68.5 28 26 72.6 5

IMPORTANT INFORMATION
The wheel stud P.C.D. of ALL the above Chrysler 300C + Dodge Charger discs are definitely 115 mm.
Correct P.C.D. wheels must be fitted.
DO NOT install any replacement wheels which have a wheel stud PCD of 114.3 mm = 4.5 inch,
because this will cause distortion of the BEARING HUB mounting face when the wheel nuts are tightened.
A new HUB will need to be installed to rectify the problem, if a wrong wheel is fitted.
Please advise your customers, failure to follow the above information will void any warranty.

CENTURA
PART NOT AVAILABLE
KB 4 Cyl GF16 1975 - 77 F 206 3
REFERENCE ONLY Solid 249 35.6 12.9 11.5 69 4

crossfire
all models - exc. SRT-6 2004 - 2006 F 288 3 Vented 300 47 28 25.4 67 5
R 267 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 56 9 7.3 67 5

DURANGO
2WD & 4WD 1998 - 02 F 2440 3 3 Vented 287 64 24 22.6 73.5 6
All Models 2005 - on F 2442 3 3 Vented 336 67.6 28 26.4 78.6 5
R 2443 3 3 Vented 354 72.1 22 20.4 78.6 5

neon
Neon All Models 1996 - 99 F 175 3 Vented 257 38 20 18.4 61 5
SE, LX Sedan R 166 3 3 Solid 270 53 9 7.25 58 5
Neon All Models 2000 - on F 165 3 Vented 257 38 22 20.4 61 5
R 166 3 3 Solid 270 53 9 7.25 57 5

PT CRUISER
2.4L DOHC 2000 - on F 167 3 3 Vented 280 39.5 23 21.4 61 5
R 166 3 3 Solid 270 53 9 7.25 61 5
2.4 DOHC TURBO 2003 F 2446 3 Vented 280 39.9 28 26.4 61 5
GT 2.4L DOHC TURBO 2004 - on
R 2447 3 Solid 270 53.2 11.9 7.25 57.5 5
LIMITED 2004 - on F 2446 3 Vented 280 39.9 28 26.4 61 5
2.4L DOHC TURBO R 166 3 3 Solid 270 53 9 7.25 61 5

46 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CHRYSLER / DODGE C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

VALIANT
PART NOT AVAILABLE
VC, VE, VF 9/68 - 70 F 201 3
REFERENCE ONLY Solid 279.4 61 12.7 11.2 79 5
VG (early) 1970 F 204 3 Vented 282
PART NOT AVAILABLE
62 24 22.3 78 5
REFERENCE ONLY
P.C.D. 101mm Rare Model
VG, VH, CH, 1970 - 73 F 202 3 Vented 283 63 24 22.3 78 5
VJ, VK, CJ, CK, CL
(Girlock Calipers) P.C.D. 114mm

CL, CM 1976 - 81 F 203 3 Vented 282 56.5 25.4 24.4 78 5

PART NOT AVAILABLE
REFERENCE ONLY

VIPER
All models 1992 - 2002 F 52430 3 Vented 330 62.7 32 30.1 73.5 6
Front disc in 5000 series only
R 2431 3 3 Vented 330 43.7 22.6 20.4 73.5 6
VIPER SRT10 2003 - 2005 F 42448 3 3 Vented 355 59.6 32 30 73.5 6
R 42449 3 Vented 355 52.2 32 30 73.5 6

Voyager
GS (SE, LE & LTD) 1997 - 2000 F 177 3 Vented 282 38 24 22.4 73.4 5
RG (SE, LX & LTD) 2001 - 09/07 F 776 3 Vented 302 39 28 26.5 73.4 5
Front & All wheel drive R 777 3 Solid 290 56 12.5 11.25 72 5
Voyager III series 02/00 - on F 776 3 Vented 302 39 28 26.5 73.4 5
2.4, 3.3, 3.3 AWD, 3.8
2.5 CRD 08/05 - on
2.8 CRD 06/04 - on

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 47
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

AMI SUPER
1.0 1973 - 76 F 054 3 Solid 269 29.5 9 7 87 6

AX
GTI 1991 - 96 F 273 3 Vented 247 35 20.5 18.6 66 4

BERLINGO
1.4i 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.4i (vented disc) 1996 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.6i 16V 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.6i 16V 2001 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.8i 1997 - 01 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9L Diesel 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.9L Diesel 1996 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
2.0 HDi Turbodiesel 2000 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4

BERLINGO ENTREPRISE
1.4i 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.4i (vented disc) 1996 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Diesel 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.9 Diesel 1996 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel 10/02 - on F 2274 3 Vented 266 34.2 22 20 66 4
2.0 HDi Turbodiesel 2000 - 9/02 F 274 3 Vented 266 27.5 20.5 18.6 66 4

BX
19 16V 1987 - 94 F 274 3 Vented 266 27.5 20.5 18.6 66 4

48 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

C2
1.6i 16V 2003 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.6i 16V VTS (90kW) 2004 - on F 2275 3 Vented 283 34.2 26 24 66 4

C3
1.4 16V HDi Turbodiesel 2002 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.6i 16V 2002 - on F 2274 3 Vented 266 34.2 22 20 66 4

C4
1.4i 16V (Non ESP) 10/04 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.4i 16V (with ESP) 10/04 - on F 2275 3 Vented 283 34.2 26 24 66 4
1.6 16V HDi Turbodiesel 10/04 - on F 2274 3 Vented 266 34.2 22 20 66 4
(Non ESP) (66kW)
1.6 16V HDi Turbodiesel 10/04 - on F 2275 3 Vented 283 34.2 26 24 66 4
(with ESP) (66kW)
1.6 16V 10/04 - on F 2275 3 Vented 283 34.2 26 24 66 4
HDi Turbodiesel (80kW)
1.6i 16V (Non ESP) 10/04 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.6i 16V (with ESP) 10/04 - on F 2275 3 Vented 283 34.2 26 24 66 4

C5
1.6 16V HDi Turbodiesel 2004 - on F 2275 3 Vented 283 34.2 26 24 66 4
1.8i 16V 2001 - on F 2274 3 Vented 266 34.2 22 20 66 4
2.0 HDi Turbodiesel (80kW) 2001 - 4/09 F 2275 3 Vented 283 34.2 26 24 66 4
2.0 HPi 16V 2001 - on F 2275 3 Vented 283 34.2 26 24 66 4
2.0i 16V 2001 - on F 2275 3 Vented 283 34.2 26 24 66 4

C5 Break
1.6 16V HDi Turbodiesel 2004 - on F 2275 3 Vented 283 34.2 26 24 66 4
1.8i 16V 2001 - on F 2275 3 Vented 283 34.2 26 24 66 4
2.0 HDi Turbodiesel (80kW) 2001 - 4/09 F 2275 3 Vented 283 34.2 26 24 66 4
2.0 HPi 16V 2001 - on F 2275 3 Vented 283 34.2 26 24 66 4
2.0i 16V 2001 - on F 2275 3 Vented 283 34.2 26 24 66 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 49
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CX
PART NOT AVAILABLE
2000 1974 - 9/77 F 056 3 Vented 260
REFERENCE ONLY 54 20 18 58 5
R 057 3 Solid 233 58 9 7 58 5
2200 1974 - 9/77 F 056 3
PART NOT AVAILABLE
Vented 260
REFERENCE ONLY 54 20 18 58 5
R 057 3 Solid 233 58 9 7 58 5
2400 10/77 - 85 F 056 3
PART NOT AVAILABLE
Vented 260
REFERENCE ONLY 54 20 18 58 5
R 059 3 Vented 247 35 20.5 18.6 66 4
2500 i E 10/77 - 85 F 056 3
PART NOT AVAILABLE
Vented 260
REFERENCE ONLY 54 20 18 58 5
R 059 3 Vented 247 35 20.5 18.6 66 4

D Series
PART NOT AVAILABLE
D SERIES 1966 - 76 F 050
REFERENCE ONLY Solid 300 54 12 10.8 99.5 6

GS
1015 1970 - 72 F 051 3 Solid 270 32 7 6.3 90.5 5
1200 2/71 - 78 F 054 3 Solid 269 29.5 9 7 87 6
R 053 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 178 15 7 6.3 45 4
1220 GXS Pallas 2/71 - 78 F 054 3 Solid 269 29.5 9 7 87 6
R 053 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 178 15 7 6.3 45 4

SAXO
1.6i 1996 - 04 F 273 3 Vented 247 35 20.5 18.6 66 4
1.6i 16V VTS 1996 - 04 F 273 3 Vented 247 35 20.5 18.6 66 4
R 276 3 Solid 246.5 25 8 6 71 4

XANTIA
1.6i 1993 - 97 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.8i 1993 - 02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.8i 16V 1993 - 02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Diesel 1993 - 96 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Turbo Diesel 1993 - 02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
(55/66kW) Automatic
2.0 HDi Turbo Diesel (66kW) 1993 - 02 F 274 3 Vented 266 27.5 20.5 18.6 66 44
2.0i 1993 - 02 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0i 16v 1993 - 02 F 275 3 Vented 283 27.5 22 20 66 4
2.0i Automatic 1998 - 02 F 275 3 Vented 283 27.5 22 20 66 4

50 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

XANTIA BREAK
1.8i 1995 - 02 F 275 3 Vented 283 27.5 22 20 66 4
1.9 Turbodiesel 1993 - 02 F 275 3 Vented 283 27.5 22 20 66 4
2.0 HDi Turbo Diesel (66kW) 1993 - 02 F 275 3 Vented 283 27.5 22 20 66 4
2.0i 16v 1995 - 02 F 275 3 Vented 283 27.5 22 20 66 4

XSARA
1.4 HDi Turbodiesel 1999 - 8/00 F 2274 3 Vented 266 34.2 22 20 66 4
1.4i 9/00 - 2004 F 2274 3 Vented 266 34.2 22 20 66 4
1.4i (with ABS) 1997 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.5 Diesel (with ABS) 1997 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.6i 1997 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.6i 16V 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.8i 1997 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.8i 16V 1997 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Diesel 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.9 Diesel 1997 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.9 Turbodiesel 1997 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
2.0 HDi Turbodiesel 1999 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel (66kW) 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
2.0 HDi Turbodiesel (80kW) 01 - on F 275 3 Vented 283 27.5 22 20 66 4
(upto Ch. 09064)
2.0 HDi Turbodiesel (80kW) 01 - on F 2275 3 Vented 283 34.2 26 24 66 4
(from Ch. 09065)
2.0i 16V 1997 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0i 16V (upto Ch. 09064) 9/00 - on F 275 3 Vented 283 27.5 22 20 66 4
2.0i 16V (from Ch. 09065) 9/00 - on F 2275 3 Vented 283 34.2 26 24 66 4
All Models 1997 - 04 R 276 3 Solid 246.5 25 8 6 71 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 51
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

XSARA BREAK
1.4 HDi Turbodiesel 2003 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.4i 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.4i (Non ABS) 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.4i (with ABS) 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.5 Diesel (Non ABS) 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.5 Diesel (with ABS) 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.6i (Non ABS) 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.6i (with ABS) 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.6i 16V 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.8i 8/16V 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Diesel 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.9 Diesel (Non ABS) 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.9 Diesel (with ABS) 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Turbodiesel 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel 1999 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel (66kW) 9/00 - on F 2274 3 Vented 266 34.2 22 20 66 4
2.0 HDi Turbodiesel (80kW) 01 - on F 275 3 Vented 283 27.5 22 20 66 4
(upto Ch. 09064)
2.0 HDi Turbodiesel (80kW) 01 - on F 2275 3 Vented 283 34.2 26 24 66 4
(from Ch. 09065)
2.0i 16V 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0i 16V (upto Ch. 09064) 9/00 - on F 275 3 Vented 283 27.5 22 20 66 4
2.0i 16V (from Ch. 09065) 9/00 - on F 2275 3 Vented 283 34.2 26 24 66 4
All Models 1998 - on R 276 3 Solid 246.5 25 8 6 71 4

52 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

XSARA COUPE
1.4i (with ABS) 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.4i 9/00 - 04 F 2274 3 Vented 266 34.2 22 20 66 4
1.4 HDi Turbodiesel 2003 - 04 F 2274 3 Vented 266 34.2 22 20 66 4
1.6i 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
1.6i 16V 9/00 - 04 F 2274 3 Vented 266 34.2 22 20 66 4
1.8i 16V VTS 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.9 Turbodiesel 1998 - 8/00 F 273 3 Vented 247 35 20.5 18.6 66 4
2.0 HDi Turbodiesel 1999 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel (66kW) 9/00 - 04 F 2274 3 Vented 266 34.2 22 20 66 4
2.0 HDi Turbodiesel (80kW) 9/00 - on F 275 3 Vented 283 27.5 22 20 66 4
(upto Ch. 09064)
2.0 HDi Turbodiesel (80kW) 9/00 - on F 2275 3 Vented 283 34.2 26 24 66 4
(from Ch. 09065)
2.0i 16V VTS (120kW) 9/00 - on F 275 3 Vented 283 27.5 22 20 66 4
(upto Ch. 09064)
2.0i 16V VTS (120kW) 9/00 - on F 2275 3 Vented 283 34.2 26 24 66 4
(from Ch. 09065)
2.0i 16V VTS (98kW) 1998 - 8/00 F 274 3 Vented 266 27.5 20.5 18.6 66 4
All Models 1998 - 04 R 276 3 Solid 246.5 25 8 6 71 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 53
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
CITROEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

XSARA PICASSO
1.6i (Bosch System) 2000 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.6i (Lucas System) 2000 - on F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.8i 16V (Bosch System) 2000 - on F 2274 3 Vented 266 34.2 22 20 66 4
1.8i 16V (Lucas System) 2000 - on F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0 HDi Turbodiesel 2000 - on F 2274 3 Vented 266 34.2 22 20 66 4
(Bosch System)
2.0 HDi Turbodiesel 2000 - on F 274 3 Vented 266 27.5 20.5 18.6 66 4
(Lucas System)

ZX
1.6, 1.8, 1.9, 2.0 1991 - 98 F 273 3 Vented 247 35 20.5 18.6 66 4
1.9 Break Diesel 1994 - 98 F 273 3 Vented 247 35 20.5 18.6 66 4
1.9 Turbodiesel 1992 - 98 F 273 3 Vented 247 35 20.5 18.6 66 4
R 276 3 Solid 246.5 25 8 6 71 4
2.0i 16V 1992 - 98 F 274 3 Vented 266 27.5 20.5 18.6 66 4

54 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
DAEWOO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

1.5 i 3D & 5D Hatchback 9/94 - on F 890 3 Solid 236 41 12 9.7 60 4

1.5 i 4D Sedan (Racer)

cielo / espero / lanos

Cielo 2/95 - on F 890 3 Solid 236 41 12 9.7 60 4
Cielo (All 13” Wheels) 2/95 - on F 896 3 Vented 236 41 20 17 60 4
Espero CD 4D Sedan
Lanos SOHC SE 1.4L , 1.5L 6/97 - on
Cielo (All 14” Wheels) 2/95 - on F 891 3 Vented 256 41 24 22 60 4
Espero CD 4D Sedan
Lanos DOHC SX 1.5L, 1.6L 6/97 - on

KALOS
TK Sedan & Hatch 1.6L DOHC 2003 - 2005 F 2032 3 Vented 236 41 20 18 59 4

lEganza
Leganza SX (15” Wheels) 8/97 - on F 892 3 Vented 256 47 24 22 60 5
2.0 Litre, 2.2 Litre R 893 3 Solid 258 64.5 10 8 57 5

matiz
Matiz 1999 - on F 897 3 Solid 236 35 12.7 9.7 86 4

nubira
Nubira 6/97 - on F 894 3 Vented 256 47 24 22 60 4
SX, SE, CDX R 895 3 Solid 258 64.5 10 8 57 4

tacuma
Tacuma U100 2.2L T/Cam 8/2000 - on F 726 3 Vented 256 47 24 22 60 4

MUSSO 4X4 (Also listed under Ssanyong)
2.9L & 3.2L 1996 - on F 554 3 Vented 278 40 24 22 88 6
R 555 3 Solid 300 67 10.5 8.5 105 6

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 55
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
DAIHATSU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

APPLAUSE
A101 6/89 - on F 295 3 Vented 234 47 18 17 56 4
A101 6/89 - 94 R 494 3 Solid 236 40 10 9 56 4
5 Door 1.6 Litre 1998 - on F 295 3 Vented 234 47 18 17 56 4

ALTIS
SXV20 7/97 - 2002 F 733 3 Vented 255 49 28 26 62 5
MCV20 7/97 - 2002 F 735 3 Vented 276 49.5 28 26 62 5
Rear disc fits all sedans and wagons R 736 3 Solid 269 65 10 9 62 5

CHARADE
G10, G20 1980 - 1/83 F 290 3 Solid 207 39 10 9 47 4
G11 1983 - 12/86 F 294 3 Solid 208 29 11 10 47 4
G100, G102 1987 - 1/89 F 295 3 Vented 234 47 18 17 56 4
G100, G102 1987 - 1/89 F 291 3 6mm Flange 234 47 11 10 56 4
G100, G102 CX, 1989 - 1/93 F 296 3 7mm Flange 234 47 11 10 56 4
TS Van 1989 - 1/93
G202 1993 - on
G100, G200, G203 SG 1989 - 94 F 295 3 Vented 234 47 18 17 56 4

CENTRO
PART NOT AVAILABLE
MS, MX 1994 - 98 F 297 3REFERENCE
ONLY Solid 211 35 10 9 70 4
Centro MS, MX 3/95 - 2002 F 293 3 Solid 210 35 10 9 70 4

COPEN
4cyl Turbo 5/2002 - on F 2498 3 Vented 246 42 17 16 55 4

DELTA
V57, V67, V107 4/87 - on F 299 3 Vented 285 61 24 23 94 6

FEROZA
4WD F300, F310 10/88 - on F 292 Solid 277 30 12.5 11.5 96 5
4WD F300, F310 10/88 - on F 491 Vented 277 33 18 17 96 5

56 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
DAIHATSU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HANDYVAN
L80 8/85 - 2/90 F 293 3 Solid 212 35 10 9 70 4
PART NOT AVAILABLE
L55, L60 without booster 6/83 - 85 F 490 3REFERENCE
ONLY Solid 236 33 10 9 70 4
L55, L60 with booster 6/83 - 85 F 493 3 Solid 179 33 10 9 70 4

HI-JET
S75 10/83 - 5/86 F 293 3 Solid 212 35 10 9 70 4
S76 2/84 - 5/86 F 492 3 Solid 211 23 10 9 79 4

MIRA
PART NOT AVAILABLE
L200, L201 (solid disc) 3/90 - 8/92 F 297 3REFERENCE
ONLY Solid 211 35 10 9 70 4
PART NOT AVAILABLE
L200, L201 (vented disc) 8/90 - on F 298 3REFERENCE
Vented 211
ONLY 41 16 15 70 4

MOVE
L601 5/97 - on F 495 3 Vented 234 41 16 15 55 4

Pyzar
Pyzar 1997 - on F 497 3 Vented 250 47 18 17 56 4

ROCKY 4WD
Non Turbo, F20, F50, F60 10/81 - 3/84 F 292 Solid 277 30 12.5 11.5 96 5
F70, F75, F80, F85 1984 - 4/93
F7#, F8# Turbo 4/84 - 4/93 F 491 Vented 277 33 18 17 96 5
F73, F78 5/93 - on

SIrion
M100 , NM101, 1.3Lt 6/98 - on F 495 3 Vented 234 41 16 15 55 4

TERIOS
J100, J102 (DX, SX, AERO) 3/97 - on F 496 3 Solid 273 37.5 16 15 66.5 5

YRV
YRV (M200) 4 Door Wagon 7/2001 - on F 498 3 Vented 246 41 16 15 55 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 57
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
daimler C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

2.5 Litre Saloon V8 1959 - 67 F 072 3 Solid 280 51.5 9.75 8.5 82.5 5
R 073 3 Solid 287 53 9.5 8 82.5 5
Limousine 1969 - 79 R 075 3 Solid 262 25.5 12.5 11.4 70 4
Sovereign Series 1 1967 - 73 F 074
PART NOT AVAILABLE
REFERENCE ONLY Solid 283 60 12.5 11.4 82 5
Sovereign Series 2, 3 1974 - 82 F 076 3 Vented 285 60.5 24 22.9 82 5
Sovereign Series 1, 2, 3 1968 - 82 R 075 3 Solid 262 22.5 12.5 11.4 70 4
Double Six Series 1 1972 - 73 F 074 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 283 60 12.5 11.4 82 5
Double Six Series 2, 3 1973 - 82 F 076 3 Vented 285 60.5 24 22.9 82 5
Double Six Series 1, 2, 3 1972 - 82 R 075 3 Solid 262 25.5 12.5 11.4 70 4
Double Six 1982 - 86 F 076 3 Vented 285 60.5 24 22.9 82 5
R 075 3 Solid 262 25.5 12.5 11.4 70 4
Sedan 6 XJ Series 11/86 - 90 F 077
PART NOT AVAILABLE
REFERENCE ONLY Vented 295 67 22.3 21 80 5
R 078 Solid 278 68 10 8.8 74 5
Sedan 6 XJ Series with 11/86 - 90 R 075B 3 Solid 262 25.5 12.5 11.4 70 4
Dana Rear Axle
P.C.D of Large Holes 120.5 mm

58 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
EUNOS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

30X 1992 - 01/98 F 533 3 3 Vented 257 45.5 22 20 55 4

R 534 3 3 Solid 250.5 34.5 9 8 55 4
500 1992 - on F 950 3 Vented 258 49 24 22 72 5
R 951 3 Solid 261 40 9.5 8 72 5
800 - 2.5 litre Up to 5/96 F 868 3 Vented 274 50.8 28 26 72 5
R 867 3 Solid 286 57 9.5 7.5 72 5
6/96 - on F 868 3 Vented 274 50.8 28 26 72 5
R 869 3 Solid 286 57 9.5 7.5 72 5
800M - 2.3 litre Up to 5/96 F 866 3
PART NOT AVAILABLE
Vented 296
REFERENCE ONLY 51 28 26 72 5
R 867 3 Solid 286 57 9.5 7.5 72 5
6/96 - on F 866 3
PART NOT AVAILABLE
Vented 296
REFERENCE ONLY 51 28 26 72 5
R 869 3 Solid 286 57 9.5 7.5 72 5

FERRARI
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

Dino 208 GT4 1973 - 5/86 F 070 Vented 272

PART NOT AVAILABLE
REFERENCE ONLY 78 22 20 58 5
308 GT4 / GTB / GTS 1973 - 5/86 R 071 3 Vented 277 73 20 18 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 59
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Fiat C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

124, 125, 127, 128

All Models 1966 - 85 F/R 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

130
All Models 1976 - on F 162 3
PART NOT AVAILABLE
REFERENCE ONLY Vented 275 72 18.5 17 59 5

131
All Models 1974 - 85 F/R 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

132
All Models 1972 - 76 F/R 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4
GLS, 2000 GLS 1979 - 82 F 161 3 Solid 251.5 51.2 11 9.5 62 4

850
Coupe, Spider, Sport, 1968 - 72 F/R 160 3
PART NOT AVAILABLE
Solid 227 46 10.8 9.7 62 4
REFERENCE ONLY
Special, Super

X 1/9
All Models 1972 - 88 F/R 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

ARGENTA
All Models 1981 - 86 F 160 PART NOT AVAILABLE
3 Vented 257
REFERENCE ONLY 51.5 12 10.8 62 4

BRAVO
2.0i 20V HGT 1995 - on F 665 3 3 Vented 284 44 22 20.4 59 4

COUPE
2.0i 16V Turbo 1994 - on F 665 3 3 Vented 284 44 22 20.4 59 4
2.0i 20V Turbo (FA/175) 1996 - 00 F 2160 3 3 Vented 305 45 28 26 59 4

CROMA
2.0i Turbo, 2.5i V6 1993 - 96 F 665 3 3 Vented 284 44 22 20.4 59 4

MAREA
2.0i 20V (155/150) 1996 - 03 F 665 3 3 Vented 284 44 22 20.4 59 4
2.4 Turbodiesel (125) 1996 - 99 F 665 3 3 Vented 284 44 22 20.4 59 4
2.4 JTD Turbodiesel (130) 1999 - 00 F 665 3 3 Vented 284 44 22 20.4 59 4

60 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter

Fiat C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MAREA WEEKEND
2.0i 20V (155/150) 1996 - 03 F 665 3 3 Vented 284 44 22 20.4 59 4
2.4 Turbodiesel (125) 1996 - 99 F 665 3 3 Vented 284 44 22 20.4 59 4
2.4 JTD Turbodiesel (130) 1999 - 00 F 665 3 3 Vented 284 44 22 20.4 59 4

PANDA
All Models (except Selecta) 1980 - 04 F 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

REGATA
70, 75, 85, 100, Diesel 1.7 1983 - 90 F 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4
Diesel 1.9 1983 - 90 F 164 3 Solid 257 51.5 12 10.8 62 4
Turbodiesel 1.9 1986 - 90 F 164 3 Solid 257 51.5 12 10.8 62 4

REGATA WEEKEND
70 1983 - 90 F 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4
100 1984 - 90 F 164 3 Solid 257 51.5 12 10.8 62 4
Diesel 1.7 1983 - 90 F 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4
Diesel 1.9 1984 - 90 F 164 3 Solid 257 51.5 12 10.8 62 4
Turbodiesel 1.9 1986 - 90 F 164 3 Solid 257 51.5 12 10.8 62 4

RITMO
1.1, 1.3, 1.5 1978 - 88 F 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4
1.6 1986 - 88 F 164 3 Solid 257 51.5 12 10.8 62 4
105 TC 1981 - 4/83 F 164 3 Solid 257 51.5 12 10.8 62 4
105 TC 5/83 - 85 F 164 3 Solid 257 51.5 12 10.8 62 4
Diesel 1978 - 88 F 164 3 Solid 257 51.5 12 10.8 62 4
Turbodiesel 1986 - 88 F 164 3 Solid 257 51.5 12 10.8 62 4

SPORT SPIDER (124)

2.0i 1982 - 84 F 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4
2.0i 1984 - 86 F 164 3 Solid 257 51.5 12 10.8 62 4
R 160 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

UNO
0.9, 1.0, 1.1, 1.3, 1.4, 1.5 1983 - 95 F 160 3
PART NOT AVAILABLE
Solid 227 46 10.8 9.7 62 4
REFERENCE ONLY
Diesel 1.3

FIORINO
(127) 1978 - 87 F 160 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 61
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Fiat C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MARENGO
(Regata) 1983 - 90 F 164 3 Solid 257 51.5 12 10.8 62 4

PANDA CITIVAN
All Models 1992 - 04 F 160 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

PANDA VAN
All Models 1986 - 04 F 160 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

UNO VAN
1.0 1990 - 95 F 160 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 227 46 10.8 9.7 62 4

62 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

AMERICAN IMPORTED (early)

Fairlane Imported 1974 - 79 F 123 3 Vented 300 81 30 28.5 Hub 5
LTD Imported 1977 - 79
PART NOT AVAILABLE
Ranchero REFERENCE ONLY

Thunderbird
Torino

capri
GT1600, Deluxe, XL 1969 - 73 F 113 3 Solid 245 27 12.7 11.4 68 4
GT3000 1970 - 73
SA, SC, SE Convertible 1989 - 94 F 930 3 Vented 238 31 18 16 75 4
(Non Turbo)
SA, SC, SE Convertible 1989 - 94 F 101 3 Vented 260 32 18 16 75 4
(Turbo)

SA, SC, SE Convertible 1989 - 94 R 931 3 Solid 222 35 10 8 Hub 4

Hub Seal Dia. = 54mm

CORTINA
PART NOT AVAILABLE
220, 240, 440, MKI, MKII 10/62 - 71 F 112 3
REFERENCE ONLY Solid 240 27 9.5 8.6 68 4
English Import 1975 - 78 F 118 3 3
PART 3
AVAILABLE
NOT Solid 247 26.5 12.5 11.4 68 4
REFERENCE ONLY
DB625 Pads
TC, TD 1971 - 5/77 F 115 3 AVAILABLE
NOT
PART Solid 246 62 12.5 11.5 69 4
REFERENCE ONLY
DB625 Pads
TE, TF 6/77 - 8/82 F 116 3 Vented 237 63.5 22.4 20 78 4
DB1024 Pads

CORSAIR
UA 1989 - 92 F 617 3 Vented 257 49 22 20 68 4
R 614 3 Solid 257 45 10 8 68 4

COUGAR
COUGAR 3 Door Hatch 1999 - on F 508 3 Vented 278 47.5 24 22.2 64 4
2.5 Litre V6 R 509 3 Vented 253 43.5 20 18 64 4

crown victoria
All models (incl Police) 1998 - 2001 F 2148 3 3 Vented 316 66 28 27.75 71.7 5
All models (incl Police) 2003 - 2009 F 2146 3 3 Vented 305.5 45 28 26.35 71.8 5
R 2149 3 3 Vented 295 58.5 19 18 70.7 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 63
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ESCORT
Sedan, P/Van (Mk 1) 1970 - 75 F 117 3
PART NOT AVAILABLE Solid 219 23 9.5 8.5 63 4
REFERENCE ONLY
DB538 Pads
Sedan, P/Van (Mk 2) 1975 - 81 F 118 3
PART NOT AVAILABLE Solid 247 26.5 12.5 11.4 68 4
REFERENCE ONLY
DB625 Pads
PART NOT AVAILABLE
RS2000 5/79 - 81 F 118 3
REFERENCE ONLY Solid 247 26.5 12.5 11.4 68 4
DOHC - 1.8L 1991 - 1996 F 533 3 3 Vented 257 45.5 22 20 55 4
w/ front caliper casting #22-14 R 534 3 3 Solid 250.5 34.5 9 8 55 4
SOHC - 1.9L 1991 - 1996 F 532 3 Vented 235 45.5 22 20 55 4
w/ front caliper casting #22-13
all models - Front 1997 - 2003 F 533 3 3 Vented 257 45.5 22 20 55 4
w/rear disc brakes R 534 3 3 Solid 250 34.5 9 8 55 4

64 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - falcon (early) C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

falcon / FALCON UTE

PART NOT AVAILABLE
XP 5 Stud 3/65 - 66 F 114A 3REFERENCE
ONLY Solid 274 50 12.7 11.5 79 5
XP 4 Stud 3/65 - 66 F 114B 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 274 50 12.7 11.5 79 4
XR, XT 6 Cyl. 1966 - 6/69 F 104 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 273 50 12.7 11.5 79.5 5
XR, XT 8 Cyl. 1966 - 6/69 F 105 3 Solid 280 50 16 14.6 79.5 5
XW, XY, XA, XB 7/69 - 10/75 F 106 3 Hat Only 287 58.5 24 22.2 83 5
XW, XY, XA, XB Special Note * 7/69 - 10/75 F 106H 3 3 With 287 75 24 22.2 Hub 5
Studs
XB, XC (Rear) (9” DIFF) 11/73 - 79 R 103 3 Vented 287 58.5 24 22.2 83 5
XB, XC, XD, XE, XF Incl. Ute 10/75 - 88 F 107 3 3 3 Vented 287 75 24 22.2 Hub 5
XF Ute, XG Longreach 1988 - 95
Complete with Studs & Cups
XD (Rear) Flange Thickness 0.350 inch 1979 - 81 R 108 3 Vented 287 70 24.6 22.2 70.5 5
XE, XF (Rear) Flange Thickness 0.250 inch 1982 - 88 R 109 3 Vented 287 71 24 22.2 70.5 5
EA, EB, ED (Not ABS) 1988 - 94 F 110B 3 3 Vented 287 70 24 22.2 Hub 5
XR6, XR8 Supplied with Grease Cap
EA, EA Series II (Rear) 1988 -12/89 R 111A 3 3 Solid 287 62 15 14 70.5 5
EA Series II, EB, ED 1990 - 94 R 111B 3 3 Solid 287 61 13 12 70.5 5
XR6, XR8 (Rear)
XG Longreach, XH 1992 - on
EB, ED with ABS 7/91 - 94 F 130 3 Vented 287 115 24 22.2 Hub 5
XR6, XR8 Includes Sensor Ring
EF, EL with ABS 1994 - 98 F 132** 3 Vented 287 115 25 21 Hub 5
XR6, XR8 Includes Sensor Ring
XH incl. Panel Van with ABS
EF, EL (Not ABS) 1994 - 98 F 131* 3 Vented 287 115 25 21 Hub 5
XH incl. Panel Van non ABS

EF, EL XR6, XR8 (Rear) 1994 - 98 R 133 3 3 Solid 299 56.5 10.5 8.5 70.5 5
**dba 134 now supersedes to dba 132 aS PER FORD AUSTRALIA SPECIFICATION
*DBA 135 now supersedes to dba 131 aS PER FORD AUSTRALIA SPECIFICATION

SPECIAL NOTE: * DBA 106H is a direct replacement for a DBA 106 + Hub
* Check dimensions Please check bearings as they differ on the various models (Bearings not supplied)

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 65
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - (falcon) C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

falcon / FALCON ute (continued)

AU + UTE 1998 - 3/00 F 500 3 3 Vented 287 70 24 21 71.8 5
R 501 3 3 Solid 287 51.5 10.5 8.5 70.5 5
AU II, AU III + UTE 3/2000 - on F 502 3 3 Vented 287 65 28 25.6 71.8 5
(non Brembo upgrade) R 503 3 3 Solid 287 51 16 14.5 70.5 5
BA incl RTV, BF Mark I & II 2002 - 2005 F 504 3 3 3 Vented 298 65 28 26 71.5 5
XR6 4.0L DOHC
BA XR6T 4.0L Turbo 2002 - 2005 R 505 3 3 3 Solid 303 51 16 14.5 70.5 5
BA XR8 5.4L V8 4V 2003 - 2005
BF Mark I XR6T 4.0L Turbo 2005 - 2006 F 42107 3 Vented 322 68 28 26 71 5
42108 3
XR8 5.4L V8 R Vented 328 59 26 24 71 5
FG SERIES 2008 - on F 504 3 3 3 Vented 298 65 28 26 70.5 5
XT, XR6, G6, G6E
R 505 3 3 3 Solid 303 51 16 14.5 70.5 5
BF Mark II, FG SERIES 2006 - on F 42107 3 Vented 322 68 28 26 71 5
XR6-Turbo, XR8, G6E-Turbo
R 4505 3 Solid 303 51 16 14.5 70.5 5

FORD PREMIUM UPGRADE - BA SERIES

BA XR6, XR6T, XR8 2002 - 2005 F 42104 3 3 Vented 325 45.3 32 30 71.5 5
(Black Ford 2 Piston front caliper) R 505 3 3 3 Solid 303 51 16 14.5 70.5 5

SPECIAL
NOTE: NOTE: 
BF FPV BF FPV
Premium Premium
Brake Kit =Brake Kit = 6Brembo
Brembo Piston6 Front
Front and 4 Piston Rear
Calipers Calipers. Standard
- Standard on SUPER on PURSUIT,
Super
Optional on PURSUIT & F6 TORNADO
Pursuit, optional on Pursuit & F6 Tornado.

66 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - tickford / FPV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

TICKFORD / FPV - F6 UTE

FG - Performance Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5

TICKFORD / FPV - F6X

FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5

TICKFORD / FPV - F6 TORNADO

BF - Performance Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
BF - Premium Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5

TICKFORD / FPV - F6 TYPHOON

BA - Performance Brakes 2003 - 05 F 42104 3 3 Vented 325 45.3 32 30 71.5 5
Blue FPV 2 Piston Calipers
R 505 3 3 Vented 303 51 16 14.5 70.5 5
BF - Performance Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
BF - Premium Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5

TICKFORD / FPV - GS SEDAN & UTE

FG - Standard Brakes 2009 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
2 Piston Front Calipers
R 42108 3 Vented 328 59 26 24 71 5
FG - Performance Brakes 2009 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 67
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - tickford / FPV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

TICKFORD / FPV - GT
EL Limited Edition 1997 - 98 F 136 3 Vented 329 41 28 26.4 HUB 5
R 133 3 Solid 299 56.5 10.5 8.5 70.5 5
BA - Performance Brakes 2003 - 05 F 42104 3 3 Vented 325 45.3 32 30 71.5 5
Blue FPV 2 Piston Calipers
R 505 3 3 Vented 303 51 16 14.5 70.5 5
BA - Premium Brakes 2003 - 05 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5
BF - Performance Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
BF - Premium Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5
FG - Performance Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5

TICKFORD / FPV - GT-P

BA - Premium Brakes 2003 - 05 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5
BF - Premium Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5
FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5

68 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - tickford / FPV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

TICKFORD / FPV - GT E
FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5

TICKFORD / FPV - PURSUIT UTE
AU III Series 2000 - 03 F 506 3 3 3 Vented 329 48.3 28 25 71.8 5
Performance Brakes
Grey 2 Piston Front Calipers
R 503 3 3 Solid 287 51 16 14.5 70.5 5
AU III Series 2000 - 03 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Premium Brakes
4 Piston Front Calipers
R 503 3 3 Solid 287 51 16 14.5 70.5 5
BA 2003 - 05 F 42104 3 3 Vented 325 45.3 32 30 71.5 5
Performance Brakes
Blue FPV 2 Piston Calipers
R 505 3 3 Solid 303 51 16 14.5 70.5 5
BA - Premium Brakes 2003 - 05 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
4 Piston Front Calipers
R 42108 3 Vented 328 59 26 24 71 5
BF - Performance Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
BF - Premium Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
FG - Performance Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 4 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 69
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - tickford / FPV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

TICKFORD / FPV - PURSUIT 250

AU III Series 2000 - 03 F 506 3 3 3 Vented 329 48.3 28 25 71.8 5
Performance Brakes
Grey 2 Piston Front Caliper
R 503 3 3 Solid 287 51 16 14.5 70.5 5
AU III Series 2000 - 03 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Premium Brakes
4 Piston Front Calipers
R 503 3 3 Solid 287 51 16 14.5 70.5 5

TICKFORD / FPV - SUPER PURSUIT UTE

BF - Premium Brakes 2005 - 07 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5
FG - Premium Brakes 2008 - on F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Brembo 6 Piston Calipers
R 42108 3 Vented 328 59 26 24 71 5

TICKFORD / FPV - TE50

AU III Series 2000 - 03 F 506 3 3 3 Vented 329 48.3 28 25 71.8 5
Performance Brakes
Grey 2 Piston Front Caliper
R 503 3 3 Solid 287 51 16 14.5 70.5 5
AU III Series 2000 - 03 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Premium Brakes
4 Piston Front Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5

TICKFORD / FPV - TS50

AU III Series 2000 - 03 F 506 3 3 3 Vented 329 48.3 28 25 71.8 5
Performance Brakes
Grey 2 Piston Front Caliper
R 503 3 3 Solid 287 51 16 14.5 70.5 5
AU III Series 2000 - 03 F 42102 3 3 Vented 355 50.5 32 30 71.8 5
Premium Brakes
4 Piston Front Calipers
R 507A 3 3 Vented 330 51 28 26 70.5 5
R 507B 3 3 Vented 330 51 28 26 70.5 5

70 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

FAIRLANE / FAIRMONT
ZA, ZB 6 Cyl. 1966 - 6/69 F 104 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 272 50 12.5 11.5 79.5 5
ZA, ZB 8 Cyl. 1966 - 6/69 F 105 3 Solid 279 50 16 14.6 79.5 5
ZC, ZD, ZF, ZG 7/69 - 10/75 F 106H 3 Special 287 75 24 22.2 Hub 5
Complete with Studs Note *
ZG, ZH (Rear) 11/73 - 79 R 103 3 Vented 287 58.5 24 22.2 83 5
ZG, ZH, ZJ, ZK, ZL 10/75 - 88 F 107 3 3 3 Vented 287 75 24 22.2 Hub 5
Complete with Studs & Cups
ZJ (Rear) 1979 - 81 R 108 3 Vented 286 71.5 24 22.2 70.5 5
Flange Thickness 0.350 inch
ZK, ZL (Rear) 1981 - 88 R 109 3 Vented 286 71.5 24 22.2 70.5 5
Flange Thickness 0.250 inch
NA, NA Series Il, NC 1988 - 6/91 F 110B 3 3 Vented 287 70 24 22.2 Hub 5
(Not ABS)
Supplied with Grease Cap
NA, NA Series II (Rear) 1988 - 1/90 R 111A 3 3 Solid 287 62 15 14 70.5 5
NA Series II, NC (Rear) 1990 on R 111B 3 3 Solid 287 61 13 12 70.5 5
NC with ABS 7/91 on F 130 3 3 Vented 287 115 24 22.2 Hub 5
Includes Sensor Ring
NF, NL with ABS Until 1/11/96 F 132 3 3 Vented 287 115 25 22 Hub 5
Includes Sensor Ring only
NL with ABS 1/11/96 - on F 132 3 3 Vented 287 115 25 22 Hub 5
Includes Sensor Ring
NF, NL (Rear) 2/95 - on R 133
3 3 Solid 299 56.5 10.5 8.5 71 5
AU 1998 - on F 500 3 3 Vented 287 70 24 21 71.8 5
R 501 3 3 Solid 287 51.5 10.5 8.5 70.5 5
AU II, AU III - all models 2000 - on F 502 3 3 Vented 287 65 28 25.6 71.8 5
(non Brembo upgrade) R 503 3 3 Solid 287 51 16 14.5 70.5 5
BA, BF 4.0L DOHC 2002 - on F 504 3 3 3 Vented 298 65 28 26 71.5 5
BA, BF 5.4L SOHC V8 R 505 3 3 3 Solid 303 51 16 14.5 70.5 5
BF 5.4L SOHC V8 2005 - on F 42107 3 Vented 322 68 28 26 71 5
(optional brake upgrade) R 42108 3 Vented 328 59 26 24 71 5

SPECIAL NOTE: * DBA 106H is a direct replacement for a DBA 106 + Hub
* Check dimensions Please check bearings as they differ on the various models (Bearings not supplied)

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 71
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

LTD
54J (Rear) 6/73 - 79 R 103 3 Vented 287 58.5 24 22.2 83 5
FC, FD, FE 1979 - 88 F 107 3 3 3 Vented 287 75 24 22.2 Hub 5
Complete with Studs & Cups
FC (Rear) 1979 - 81 R 108 3 Vented 287 71.5 24 22.2 70.5 5
Flange Thickness 0.350 inch
FD, FE (Rear) 1982 - 88 R 109 3 Vented 287 71.5 24 22.2 70.5 5
Flange Thickness 0.250 inch
DA, DA Series II, DC 1988 - 7/91 F 110B 3 3 Vented 287 70 24 22.2 Hub 5
(Not ABS)
Supplied with Grease Cap

DA, DA Series II (Rear) 1988 - 1/90 R 111A 3 3 Solid 287 62 15 14 70.5 5

DA Series II, DC (Rear) 1990 - 2/95 R 111B 3 3 Solid 287 61 13 12 70.5 5
DC with ABS 7/91 - 2/95 F 130 3 3 Vented 287 115 24 22.2 Hub 5
Includes Sensor Ring
DF, DL with ABS Until 1/11/96 F 132 3 3 Vented 287 115 25 22 Hub 5
Includes Sensor Ring only
DL with ABS 1/11/96 - on F 132 3 3 Vented 287 115 25 22 Hub 5
Includes Sensor Ring
DF, DL (Rear) 2/95 - on R 133
3 3 Solid 299 56.5 10.5 8.5 71 5
AU 1998 - 3/00 F 500 3 3 Vented 287 70 24 21 71.8 5
R 501 3 3 Solid 287 51.5 10.5 8.5 70.5 5
AU II, AU III - all models 3/2000 - on F 502 3 3 Vented 287 65 28 25.6 71.8 5
(non Brembo upgrade) R 503 3 3 Solid 287 51 16 14.5 70.5 5
BA, BF 4.0L DOHC 2002 - on F 504 3 3 3 Vented 298 65 28 26 71.5 5
BA, BF 5.4L SOHC V8 R 505 3 3 3 Solid 303 51 16 14.5 70.5 5
BF 5.4L SOHC V8 2005 - on F 42107 3 Vented 322 68 28 26 71 5
(optional brake upgrade) R 42108 3 Vented 328 59 26 24 71 5

FESTIVA
WA 10/91 - 94 F 635 3 Solid 219 37 13 11 75 4
WB Manual 1994 - 97 F 530 3 Vented 235 45.5 18 16 55 4
WF 3 & 5 Door 11/97 - 2000
WB Automatic 1994 - 97 F 532 3 3 Vented 235 45.5 22 20 55 4
WF 5 Door 11/97 - 2000

72 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

FIESTA
Fiesta 1996 - on F 854 3 Vented 239.5 43 20 18 63.5 4
1.6L 16V LX, Zetec, Ghia 11/03 - on F 2100 3 Vented 258 43.5 22 20 63.5 4

FOCUS
1.8L, 2.0 all models 2002 - 05 F 2100 3 3 Vented 258 43.5 22 20 63.5 4
R 2109 3 Solid 253 33 10 8.9 63.5 4
2.0L 127kW ST170 2003 - 06 F 2101 3 Vented 300 43.5 24 22 63.5 4

R 2103 3 Solid 280 33 10 8.9 63.5 4

2.0, 1.6TD, 1.8TD, 2.0TD 2003 - 07 F 2380 3 Vented 300 48.6 25 23 64 5
C-MAX & Cabriolet R 2121 3 3 Solid 280 41 11 9 64 5
LS, LT, LV 1.6L, 2.0L & Diesel 2005 - on F 2118 3 Vented 278 48.5 25 23 64 5
R 2119 3 Solid 265 41 11 9 64 5
XR5 Turbo 2.5L 5cyl Turbo 04/06 - on F 2120 3 3 Vented 320 48.6 25 23 64 5
R 2121 3 3 Solid 280 41 11 9 64 5

FORMULA FORD (Special application)

Formula Ford Disc PCD=148.5 F/R 4993 3 3 Solid 248 7 7 126 6
Flat design
Formula Ford Disc PCD=95 F/R 4994 3 3 Solid 248 41 7 76 4
Hat- design
Formula Ford Disc PCD=148.5 F/R 42999 3 3 Solid 254 9.65 9.65 126 6
Flat- slotted - AP calipers

FORMULA 3
Formula 3 disc PCD=176mm F/R 5003.1 3 Vented 277.8 16.5 15.9 156 8
Flat- - slotted disc only

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 73
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

KA
TB KA 1.3L Hatchback 1999 - on F 529 3 Solid 240 43 12 10 63.5 4
KA 1.3L Series II 2000 - on F 168 3 Vented 240 43 20 18 63.5 4

LASER / METEOR
KA, KB 1981-85 F 100 3 Solid 228 31 11 10 75 4
GA, GB 1982-85
KC, KE (Non-Turbo) 1985-90 F 930 3 Vented 238 31 18 16 75 4
GC 1985-87
KE Turbo 2WD, 4WD 1987-90 F 101 3 Vented 260 32 18 16 75 4
KC, KE Except 4WD 1985-90 R 931 3 Solid 222 35 10 8 Hub 4
Hub Seal Dia. = 54mm
KC, KE Except 4WD 1985-90 R 933 3
PART NOT AVAILABLE
Solid 221 35 10 8 Hub 4
REFERENCE ONLY
Hub Seal Dia. = 65mm
KE TX3 Turbo 4WD 1987-90 R 932 3 Solid 247 30
PART NOT AVAILABLE
REFERENCE ONLY 10 8 75 4
KF, KH - 1600 EFi 4/90-94 F 530 3 Vented 235 45.5 18 16 55 4
Manual Transmission Check Dimensions

KF, KH 1600 Automatic 4/90 - 94 F 532 3 3 Vented 235 45.5 22 20 55 4

KH 1800 SOHC, DOHC 10/91-94 Check Dimensions
KF, KH, TX3 1.8 DOHC 11/89-94 F 533 3 3 Vented 257 45.5 22 20 55 4
KJ, KL 1.6, 1.8 1994 - 2000
KF, KH, 1.8L SOHC 4/90 - 94 R 531 3 3 Solid 231 35 9 8 55 4
KF, KH, KL TX3 2WD 10/91 - 2000 R 534 3 3 Solid 250.5 34.5 9 8 55 4
KF, KH, KL TX3 4WD Turbo 4/90 - 2000 F 533 3 3 Vented 257 45.5 22 20 55 4
KF, KH, KJ, KL, 1.8L DOHC 4/90 - 2000 R 534 3 3 Solid 250.5 34.5 9 8 55 4
KN, KQ 1.6L (LXi) 1999 - 2002 F 532 3 3 Vented 235 45.5 22 20 55 4
KN, KQ 1.8L 1999 - 2002 F 576 3 Vented 258 47 24 22 55 4
(GLXi, SR) R 539 3 Solid 261 40 10 8 55 4
KQ 2.0L 2000 - 2002 F 577 3 Vented 258 48.5 24 22 72 5
SR2 R 951 3 Solid 261 40 9.5 8 72 5

MONDEO
HA , HC, HD & HE 7/95 - 10/02 F 850 3 Vented 260 47 24 22.2 63.5 4
2.0L D.O.H.C R 851 3 Vented 253 44 20 18 63.5 4
All models inc XR5 Turbo 11/06 - on F 2128 3 Vented 300 52 28 26 63.5 5
R 2129 3 Vented 302 51 11 9 63.5 5

74 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MUSTANG
All 1968 - 73 F 106H 3 3 Vented 287 75 24 22.2 Hub 5
Complete with Studs
Cobra standard models only 1994 - 04 F 855 3 Vented 276 46.6 26 24.8 71 5
without upgraded discs R 856 3 Solid 267 50 14 12.8 71 5
Cobra Bullitt & MACH 1 1994 - 04 F 069 3 3 3 Vented 330 43.5 28 26.4 71 5
suits vehicles fitted R 102A 3 RH Vented 296 51 18 16.8 71 5
with upgraded OE rotors 102B 3 LH Vented 296 51 18 16.8 71 5
V6 2005 - 06 F 2115 3 3 Vented 293 48.5 30 28.4 71 5
R 2114 3 3 Vented 300 35 19 17.4 71 5
GT (V8) 2005 - 06 F 2113 3 3 3 Vented 316 48.5 30 28.4 71 5
R 2114 3 3 Vented 300 35 19 17.4 71 5
Shelby Cobra GT500 2007 - on F 2124 3 3 3 Vented 355 47 32 30 71 5
R 2114 3 3 Vented 300 35 19 17.4 71 5

PROBE
w/ rear disc 1993 - 97 F 950 3 Vented 258 49 24 22 72 5
R 951 3 Solid 261 40 9.5 8 72 5
w/ rear drum 1993 - 97 F 950 3 Vented 258 49 24 22 72 5

TAURUS
Ghia 4 dr sedan 2/96 - 99 F 852 3 Vented 276 46.5 26 24.75 71 5
R 853 3 Solid 257 39.5 14 12.75 64.5 5

TELSTAR
AR 5/83-9/85 F 119 3 Solid 250 35 14 12.5 75 4
AS 9/85-9/87 F 334 3 Vented 250 36 20 18.5 75 4
AR, AS 5/83-9/87 R 945 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 254 50.2 10.2 9 Hub 4
AT 10/87-89 F 633 3 Vented 264 47 24 22 64 5
AV TX-5 1990-1/92 R 634 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 258 50 10 8 Hub 5
AX, AY 1992 - on F 950 3 Vented 258 49 24 22 72 5
R 951 3 Solid 261 40 9.5 8 72 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 75
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - TRUCKS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

F100 / BRONCO
F100, 2WD 1973 - 5/87 F 120 3 Vented 297 82 30 28.5 Hub 5
Complete with Studs & Cups
F100 4WD 1979 - 5/87 F 121 3 Vented 298 69 30 28.5 98.5 5
Bronco 1981 - 87

F150
F150 5/87 - 90 F 120 3 Vented 297 82 30 28.5 Hub 5

F150 4WD 5 Litre EFi V8 5/87 - 90 F 121 3 Vented 297 70 30 28.5 98.5 5
F150 4WD 5 Litre V8 5/87 - 92 F 937 3 Vented 298 75.5 30 28.5 Hub 5
Including EFi
F150 2WD 1986 - 94 F 995 3 Vented 319
PART NOT AVAILABLE 94 32 30 HUB 8
REFERENCE ONLY

F150 5.4L 1999 - 05 F 2150 3 Vented 308 104 26 24.5 HUB 5
5 Lug exc. Lightning
PART NOT AVAILABLE
R 863 3
REFERENCE ONLY Solid 334 57 14 12 87 5
F150 SVT 5.4L 1999 - 05 F 2151 3 Vented 308 103 30 27.7 HUB 5
5 Lug Lightning & Nascar
5.4L Supercharged V8 R 863 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 334 57 14 12 87 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

76 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - TRUCKS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

F250
F250 Single Piston, 2WD 1973 - 79 F 124 3 Vented 320 95 30 28.5 Hub 8

F250 Double Piston, 2WD 1976 - 79 F 122 3 Vented 320
PART NOT AVAILABLE 94 32 30 Hub 8
REFERENCE ONLY

F250 2WD 128A Vented 320 95 32 30 Hub 8
2/83 - 85 F
128A = 1
/2’’ Dia. Studs 128B
128B = 9/16’’ Dia Studs
F250 Double Piston, 2WD 1986 - 93 F 995 3 Vented 319
PART NOT AVAILABLE 94 32 30 HUB 8
REFERENCE ONLY

2WD, 4WD XL, XLT 07/01 - 04 F 795 3 Vented 330 144 38 36 HUB 8
5.4L, 7.3L Turbo Diesel
2WD, 4WD XL, XLT 07/01 - 04 F 798 Vented 331 99.5 38 36 128.7 8
4 Wheel ABS models
2WD/4WD XL, XLT 07/01 - 04 F 797 3 Vented 330 143 38 36 HUB 8
4.2L Turbo Diesel
all models ( Rear ) 07/01 - 04 R 796 Vented 326 98.5 30 28 126.5 8
2WD 2005 - on F 2797 3 Vented 347 116 38 36.4 HUB 8

4WD 2005 - on F 2798 Vented 347 100 38 36.4 129 8
Single Rear Wheel - all models 2005 - on R 2799 Vented 340 126 34 32.4 127 8

F350
PART NOT AVAILABLE
F350 2WD * Rare Model * 1974 - 75 F 938 3REFERENCE
ONLY Rotor Only 320 98 26 24 91 8
F350 2WD Single Rear Wheel 1976 - 79 F 125 3 Vented 320 94 32 30 Hub 8

PART NOT AVAILABLE
F350 2WD Dual Rear Wheel 1981 - 85 F 129 3REFERENCE
ONLY Rotor Only 318 93 32 30 91 8
F350 2WD Single Rear Wheel 1986 - 94 F 995 3 Vented 319
PART NOT AVAILABLE 94 32 30 HUB 8
REFERENCE ONLY

All models single rear wheel 07/01 - 04 F 795 3 Vented 330 144 38 36 HUB 8
5.4L, 7.3L Turbo Diesel
Single Rear Wheel - all models R 796 Vented 326 98.5 30 28 126.5 8
Super Cab 4 Wheel ABS 07/01 - 04 F 798 Vented 331 99.5 38 36 128.7 8
2WD Super/Crew Cab 07/01 - 04 F Not
4WD Super Cab Available

Dual Rear Wheel R 799 Vented 326 113 30 28 119.5 8

2WD 2005 - on F 2797 3 Vented 347 116 38 36.4 HUB 8

4WD 2005 - on F 2798 Vented 347 100 38 36.4 129 8

Single Rear Wheel - all models 2005 - on R 2799 Vented 340 126 34 32.4 127 8

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 77
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - TRUCKS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

COURIER / RAIDER
PART NOT AVAILABLE
All Models 1981 - 84 F 941 3REFERENCE
ONLY Solid 255 36 20 19 80 4
1.8, 2.0, 2.2, 2.6 2WD 1985 - 95 F 631 3 Vented 256 20 20 18 86 6
PD 2.6L 2WD 4/96 - on F 958 3 Vented 255.5 24 24 22 86 6
2.6L 4WD incl. Raider 5/87 - 98 F 965 3 Vented 272 25 22 20 93 6
2.6L 4WD incl. South Africa 11/98 - on F 964 3 Vented 275 24 24 22 93 6
Courier 4WD 1996 - 1998 F 959 3 Vented 274 28 28 26 93 6
Ranger / Courier 2.5L, 2.6L 2003 - on F 2952 Vented 288.5 70.5 28 26 98 6

ECONOVAN / SPECTRON ( UTES & VANS )

1400/1600/2200 5/81 - 3/84 F 939 3 Vented 275 33 20 19 85 4
1400, 1800, 2000, 2200 4/84 - 96 F 632A RH Vented 231.5 58.5 18 16 Hub 4
SWB models only
Spectron SGMD 1800 632B LH Vented
ID Groove

1800/2000/2200 3/84 - 92 F 631 3 Vented 256 20 20 18 86 6

Spectron 2000 (STD & LWB)
2000 Pickup, Crew Cab Ute 4/84 - 88 F 934 3 Vented 268 20 20 18 86 6
2000 Pickup, Crew Cab Ute 7/87 - 7/88 F 631 3 Vented 256 21 20 18 86 6
PART NOT AVAILABLE
2000 4WD Wagon 3/86 - 88 F 943 Vented 256 25 24 22 93 6
REFERENCE ONLY

Spectron SGMB 1600 2/83 - 4/84 F 939 3 Vented 275 33 20 19 85 4

Maxi 4.4m Van 12/94 - 1/97 F 857 3 Vented 256 25 24 22 86 6
2.0, 2.2 Litre
Maxi 4.7m Van 2.0, 2.2 12/94 - 1/97 F 934 3 Vented 268 20 20 18 86 6
Cabchassis
Glass Van 1.8 Litre
JG 4.0m Van S.W.B. 2/97 - on F 859A RH Vented 256 72 18 16 HUB 4

PART NOT AVAILABLE
REFERENCE ONLY
F 859B LH Vented 256 72 18 16 HUB 4

JG 4.4m Van 2.0 Litre 6/97 - on F 958 3 Vented 256 24 24 22 86 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

78 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - TRUCKS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ESCAPE
XLS 2.0L, XLS, XLT 3.0L 2000 - 05 F 957 Vented 278 47 24 22 72 5
2.3L 4 cyl, 3.0L V6 2006 - on F 2560 Vented 302.7 47.2 26 24 72 5
R 2561 Solid 302 56.1 12 11 72 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

Explorer / EXPEDITION
UN, UP, US, 11/96 - 4/01 F 860 3 Vented 286 66 26 24.5 72 5
PART NOT AVAILABLE
XLT 4.0 Litre R 861 3REFERENCE
ONLY Solid 285 58.5 12 11 71 5
PART NOT AVAILABLE
Expedition XLT 4.6 Litre V8 5/01 - 05 F 862 3REFERENCE
Vented
ONLY 308 103 30 27.7 HUB 5
PART NOT AVAILABLE
REFERENCE ONLY

SOHC 2WD R 863 3 Solid 334 57 14 12 87 5

UT V8 4.6 Litre 4WD 5/01 - 05 F 864 3 Vented 305 56.5 26 24.5 82 5
XLT 4 Door Wagon R 865 3 Solid 301 58.5 12 11 82 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 79
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
FORD - TRUCKS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MAVERICK
GY, KY 1988 - 93 F 329 3 3 Vented 294 30 20 18 104 6
Optional* R 622 3 3 Vented 315 80 18 16 111 6
Disc Rear End

TERRITORY
TX, TS, GHIA - RWD + AWD 6/2004 - on F 2107 3 3 Vented 322 68 28 26 71 5
except TURBO front disc R 2108 3 3 Vented 328 59 26 24 71 5

TRANSIT
125 Series 1973 - 86 F 127 3 Solid 270 71.5 14.3 13.2 78 5
V21, V22, V24, V33 Single Rear Wheel

175 Series, V21, V22, 1973 - 86 F 126 3 Vented 270 71.5 24 22.6 78 5
V24, V33, V51, V54 Dual Rear Wheels
VE High Roof 2.5 L Diesel 1991 - 2000 F 827 3 Solid 254 32 14.7 12.9 78 5
VE 15” Wheel 1/94 - 2000 F 828 3 Vented 270 43 24 22.15 78 5
VG 2.5Lt 14” Wheel 1/96 - 2000 F 829 3 Vented 254 43 24 22.15 78 5
VH , VJ 2001 - 06 F 871 3 Vented 294 43 24 22.15 82 5

80 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
gmc C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

848 3 Vented 317 80 32.5 31 HUB 8

Ambulance F

SIERRA 1500 1/2 TON FULL SIZE PICKUP 2WD

w/ rear disc, exc. HD 1999 - 2000 F 2000 Vented 305 61 29 27.2 79 6
2 dr 2001 - 2002 F 2000 Vented 305 61 29 27.2 79 6
4 dr HD - crew cab 2001 F 2048 Vented 325 89.5 38 36.5 118.2 8
(8 lug front)
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. - ext. cab- Quadrasteer 2002 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD - crew cab 2002 F 2048 Vented 325 89.5 38 36.5 118.2 8
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. - reg. & ext. cab- 2003 F 2000 Vented 305 61 29 27.2 79 6
2 wh. steer
2 dr. - ext. cab - Quadrasteer 2003 F 2000 Vented 305 61 29 27.2 79 6
w/ 18.5mm min, thick rear discs
2 dr. ext. cab quadrasteer 2003 F 2000 Vented 305 61 29 27.2 79 6
w/ 28.5mm min, thick rear discs
2 dr. reg. & ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
2 wh. steer
2 dr. - ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
hybrid and quadrasteer models
R 2001 Vented 330 97 30 28.5 76 6
2 dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.63” read disc hub hole
2 dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.84” rear disc hub hole
4 dr. HD - crew cab 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc, 2 wh. steer & quadrasteer

4 dr. HD - crew cab 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & 2 wh. Steer (8 lug front)

SIERRA 1500 1/2 TON FULL SIZE PICKUP 4WD

w/ rear disc 1999 - 2000 F 2000 Vented 305 61 29 27.2 79 6
2 dr. - reg. cab 2001 F 2000 Vented 305 61 29 27.2 79 6
2 dr. - ext. cab 2001 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
2 dr. 2002 F 2000 Vented 305 61 29 27.2 79 6

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 81
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
gmc C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SIERRA 1500 1/2 TON FULL SIZE PICKUP 4WD CONTINUED

2 dr. ext. cab quadrasteer 2002 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD crew cab 2002 F 2048 Vented 325 89.5 38 36.5 118.2 8
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. ext. cab 2003 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD - crew cab 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
- 2 wh. steer
R 2049 Vented 330 85.6 29 26.5 118.2 8
4 dr. Hd - crew cab 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
Quadrasteer
2 dr. - reg. & ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
2 wh. steer
2 dr. - reg. & ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
Quadrasteer
2 dr. - ext. cab 2004 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
2 Dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
2 dr. HD - ext. cab 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ 4.84” rear disc hub hole
4 dr. - crew cab - std. duty 2004 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
4 dr. HD - crew cab 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & 2 wh. steer
4 dr. HD - crew cab, 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & quadrateer
4 dr. HD - crew cab 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8
w/ rear disc & 2 wh. steer (8 lug front)

SIERRA 2500 3/4 TON FULL SIZE PICKUP 2WD

exc. 6.0L, w/ 5-speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
6.0L w/ 5-speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8

82 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
gmc C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SIERRA 2500 3/4 TON FULL SIZE PICKUP 2WD CONTINUED

exc. HD - w/ A/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD - w/ M/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
exc. HD - w/ A/T 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD - w/ M/T 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
HD - 2 wh. steer 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
exc. HD 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
exc. HD 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8

Sierra 2500 3/4 ton full size pickup 4wd

exc. 6.0L, w/ 5 speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
6.0L w/ 5-speed 1999 - 2000 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
exc. HD w/ A/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD w/ M/T 2001 - 2003 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
exc. HD w/ A/T 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.63” rear disc hub hole
R 2049 Vented 330 85.6 29 26.5 118.2 8
exc. HD w/ M/T 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
4.84” rear disc hub hole
R 2051 Vented 330 91.5 29 27 122 8
HD - 2 wh. steer 2004 F 2048 Vented 325 89.5 38 36.5 118.2 8
exc. HD 2005 - 2006 F 2048 Vented 325 89.5 38 36.5 118.2 8

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 83
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
gmc C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Suburban 1500 1/2 ton 4wD

6 lug 1992 - 1999 F 773 Vented 295 63.5 32.5 30.8 79 6
w/28.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 29 27.2 79 6
all models 2003 - on R 2001 Vented 330 97 30 28.5 76 6
w/28.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 29 27.2 79 6
all models 2003 - on
R 2001 Vented 330 97 30 28.5 76 6
w/18.5mm min. thick rear disc 2000 - 2002 F 2000 Vented 305 61 30 27.2 76 6

Suburban 2500 3/4 Ton 2wd

2 wh. steer - 4.63” 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
2049
R Vented 330 85.6 29 26.5 118.2 8
2 wh. steer - 4.84” 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
Quadrasteer 2000 - 2005
all models 2006 - on

Suburban 2500 3/4 Ton 4wd

2 wh. steer - 4.63” 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
2049
R Vented 330 85.6 29 26.5 118.2 8
2 wh. steer - 4.84” 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
Quadrasteer 2000 - 2005
all models 2006 - on

YUKON 2WD EXCEPT YUKON XL

ALL 1992 - 1994 F 773 Vented 295 63.5 32.5 30.8 79 6
w/ rear disc 2000 - 2005 F 2000 Vented 305 61 30 27.2 76 6
R 2001 Vented 330 97 30 28.5 76 6
ALL 2006 F 2000 Vented 305 61 30 27.2 76 6

YUKON 4WD EXCEPT YUKON XL

w/ rear drum 1995 - 1999 F 773 Vented 295 63.5 32.5 30.8 79 6
w/ rear disc 2000 - 2005 F 2000 Vented 305 61 30 27.2 76 6
ALL 2006 F 2000 Vented 305 61 30 27.2 76 6

84 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
gmc C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

YUKON XL 1/2 TON 2WD & 4WD

ALL 2000 - 2005 F 2000 Vented 305 61 29 27.2 79 6
R 2001 Vented 330 97 30 28.5 76 6
ALL 2006 F 2000 Vented 305 61 29 27.2 79 6

YUKON XL 3/4 TON 2WD & 4WD

w/ 4.63” rear disc hub hole 2000 - 2005 F 2048 Vented 325 89.5 38 36.5 118.2 8
2 wh. steer
R 2049 Vented 330 85.6 29 26.5 118.2 8
w/ 4.84” rear disc hub hole F 2048 Vented 325 89.5 38 36.5 118.2 8
2 wh. steer

hillman
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

Hunter, Arrow, Hustler 1967 - 74 F 085 3 Solid 244 23.5 8.8 7.9 66 4
(DB835 Pads)

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 85
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ADVENTRA
all models - AWD / 4WD 2004 - on F 2050 3 3 Vented 302 45 28 25 71.5 5
(rear suits all models 2WD+4WD) R 041 3 3 3 Solid 286 78.6 16 14 70 5

APOLLO
JK, JL SL, SLX, SLE Exec 1989 - 92 F 730 3 Vented 255 47.5 22 21 54 5
JK, JL SL, SLX, SLE Exec 1989 - 92 R 741 3 Solid 269 65 10 9 54 5
JM 4 Cyl 3/93 - 97 F 733 3 Vented 255 49 28 26 62 5
JM V6 3/93 - 97 F 735 3 Vented 275 49.5 28 26 62 5
JM Sedan 3/93 - 97 R 736 3 Solid 269 65 10 9 62 5
JM Wagon 3/93 - 97 R 734 3 Solid 288 65 10 9 62 5

ASTRA
LB, LC 1984 - 7/87 F 303 3 Solid 240 35.5 12 11 76 4
LD DB1117 Pads 7/87 - 89 F 602 3 Vented 240 45.5 18 16 60 4
TR City 1.6 Litre 8/96 - 98 F 021 3 Vented 235 41.25 20 17 60 4
TR 1.8 & 2.0 8/96 - 98 F 023 3 Vented 256 41.1 24 21 60 4
R 819 3 Solid 260 69 10 8 57 4
TS (City) 5 stud wheels 9/1998 - 05 F 815 3 Vented 280 42 25 22 70 5
TS Series II R 816 3 Solid 264 42 10 8 65 5
TS (City) 4 stud wheels 9/1998 - 05 F 817 3 Vented 256 41 24 21 60 4
TS Series II R 818 3 Solid 240 42 10 8 57 4
TS SRI Turbo 2002 - 04 F 2815 3 3 Vented 308 42.3 25.1 22 70 5
R 816 3 Solid 264 42 10 8 65 5
AH - CD, CDX, CDXi 2005 - 06 F 815 3 Vented 280 42 25 22 70 5
Coupe, Hatch, Wagon R 816 3 Solid 264 42 10 8 65 5
AH07 - SRi, Twin Top, CDTi 2007 - on F 2815 3 3 Vented 308 42.3 25.1 22 70 5
2.2L Petrol, 1.9L Diesel R 816 3 Solid 264 42 10 8 65 5
AH07 - SRi Turbo 2007 - on F 2815 3 3 Vented 308 42.3 25.1 22 70 5
2.0L Turbo R 2035 3 3 Solid 278 42.2 10 8 65 5

86 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

BARINA
MB, ML 2/85 - 88 F 012 3 Solid 215 33.5 10 8 86 4
MF, MH 1989 - 94 F 022 3 Vented 231 50 17 15 64 4
SB City 1.2L & 1.4L 1994 - 2000 F 820 3 Solid 236 41 12 9.7 60 4
SB Joy, Swing 1.4L 1994 - 2000 F 821 3 Vented 236 41 20 17 60 4
SB GSi 1.6L 1994 - 2000 F 822 3 Vented 256 41 20 17 60 4
XC 2D+4D Hatchback 4/2001 - 06 F 847 3 Vented 260 41.2 24 21 60 4
R 849 3 Solid 240 41 10 8 57 4
TK Sedan & Hatch 1.6L DOHC 2006 - ON F 2032 3 Vented 236 41 20 18 59 4

CALIBRA
YE 9/91 - on F 023 3 Vented 256 41.1 24 21 60 4
YE V6 2 Door Coupe 7/95 - on
Some models have R 024 3 Solid 270 77 10 8 57 4
DBA 038 on Front
C20 ELT Turbo, C25 XE, V6 1992 - 97 F 825 3 Vented 288 42 25 22 70 5
From Chassis : T9000001
From Chassis : T1000001
YE 2 Door Coupe 6/94 - on F 038 Vented 284
PART NOT AVAILABLE
REFERENCE ONLY 41 23.7 21 70 5
4 Wheel Drive R 039 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 270 77 10 8 65 5

CAMIRA
JB 1600cc 1982 - 84 F 011 3 Solid 236 41.25 12.7 10.7* 60 4
JD 1800cc, JE 2000cc 1984 - 8/89 F 021 *
3 Vented 236 41.25 20 17 60 4

CAPTIVA
All Models 2006 - on F 2040 3 Vented 296 52 29 27.4 70.7 5

* SPECIAL NOTE: GENERAL MOTORS HOLDEN AUTOMOTIVE REVISED SPECIFICATIONS

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 87
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

COMMODORE incl. UTE

VC, VH 4 Cyl 1980 - 83 F 013 3 Solid 256 78 15.6 14.3 Hub 5
Complete with Studs and Cups
VB, VC, VH, VK, 6, 8 Cyl 1978 - 86 F 015 3 3 Vented 270 82 22 20* Hub 5
VL 6 Cyl 1986 - 88 Complete with
VN, VG, V6 incl. UTE 1988 - 92 Studs and Cups
VP V6 (Up to & Incl. Chassis No.L569902)
VL 6 Cyl Turbo 1986 - 88 F 017 3 3 Vented 290 82 22 20* Hub 5
VL V8, Calais 1986 - 88 Complete with
VN V6 with FE2 Suspension 1988 - 9/91 Studs and Cups
VN, VG V8 incl. UTE 1988 - 92
VP V8 (Up to & Incl. Chassis No. L570556)
VQ Statesman without ABS 3/90 - 10/92
VP 6 Cyl incl. UTE 1992 F 025 3 Vented 272 82 23 20* Hub 5
(Chassis No. 569903 on) Ends 10/92 Complete with
(Limited Run) Non ABS Studs and Cups
VP V8 incl. UTE 1992 - 93 F 027 3 Vented 290 82 23 20* Hub 5
(Chassis No. 570557 on) Suitable for ABS
VP V6 Series II 11/92 - 93 No Sensor Ring
VQ Statesman Supplied
VR, VS incl. ABS incl. UTE 7/93 - on F 035 3 3 Vented 289 83 23 20* 70 5
VB, VC, VH, VK, VL 1978 - 97 R 016 3 3 Solid 279 83 10.5 8.5 70 5
VN, VP, VR, VS incl. UTE
Except IRS 6, 8 Cyl
VQ Statesman without IRS 1990 - 93
VP, IRS 1992 - 7/93 R 026 3 Solid 279 67 10.5 8.5* 70 5
VQ Statesman IRS
VR, VS IRS 7/93 - 97 R 036 3 3 Solid 279 86 10.7 8.5* 70 5
VR, VS IRS 7/93 - 97 R 036B 3 Solid 279 86 10.7 8.5* 70 10
10 Hole Stud Pattern
VS 10 Hole Stud Pattern 2/95 - 97 R 037 3 3 Solid 279 83 10.7 8.5* 70 10
VS UTE 2/95 - 00
VT, VX, VY, VZ, V6 & V8 9/97 - 05 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
+ VT, VX, VU, VZ UTE 2001 - 07
WH, WK, WL Statesman
R 041 3 3 3 Solid 286 78.6 16 14 70 5
VZ SSZ Commodore incl. Ute 2005 - 06 F 2020™ 3 3 3 3 Vented 320 83 32 30 71.6 5
R 2021™ 3 3 3 Vented 286 80 18 16 70 5

88 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

COMMODORE incl. UTE – continued

VZ SSZ 1 Tonner 2005 - 06 F 2020™ 3 3 3 3 Vented 320 83 32 30 71.6 5
3 3 3 Solid 286 78.6 16
R 041 14 70 5
VE / VEII V6 Omega, Berlina SV6 08/06 - on F 2026™ 3 3 3 Vented 298 52.2 30 28 67.5 5
Calais, Calais V, WM Statesman/Caprice R 2027™ 3 3 3 Vented 302 56 22 20 67.4 5
VE / VEII V8 Berlina, SS, SS-V 08/06 - on F 2028™ 3 3 3 Vented 321 52.2 30 28 67.5 5
Calais inc. V, WM Statesman/Caprice R 2029™ 3 3 3 Vented 324 56.1 22 20 67.4 5
VE SS-V Redline Edition 2010 - on F 42604 3 3 Vented 355 50 32 30 67.4 5
R 42029 3 Vented 324 56.1 22 20 67.4 5

COMMODORE Upgrade Options
VR, VS 7/93 - 97 F 040B 3 3 3 Vented 296 83 28 25 70 5
VT - VZ 9/97 - 05 F 046B 3 3 3 Vented 328 83 28 25 71.5 5
TM = Trademark

DBA is protecting its intellectual property rights and has begun Trademark Registration of its product part numbers

CREWMAN (UTE)
VY, VZ - Crewman, S, SS - 2WD 2002 - on F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Cross 6 / 8 - AWD / 4WD 2004 - on F 2050 3 3 Vented 302 45 28 25 71.5 5
VZ SSZ 2005 - on F 2020™ 3 3 3 3 Vented 320 83 32 30 71.6 5
(Rear all models 2WD+4WD) 2004 - on R 041 3 3 3 Solid 286 78.6 16 14 70 5

EPICA
All Models 2006 - on F 2038 Vented 278 47 24 22 60 4
R 2039 Solid 276 58.5 12 10 60 4

GEMINI
TC, TD, TE, TX, TF, TG 1975 - 5/85 F 006 3 Solid 240 47 10 8.6 68 4
RB FWD 5/85 - 87 F 007 3 Solid 227 42 11 9.6 57 4

HOLDEN
HD, HR 1965 - 67 F 001 3 Solid 253 50 9.7 9 72 5
HK, HT 1968 - 70 F 002 3 Solid 270 55 12.7 11.7 72 5
HT - V8 1969 - 71 F 003 3 Solid 270 56.5 15.9 14.7 72 5
HG
Check Spacer in Caliper
HQ - HJ 1971 - 76 F 014 3 3 3 Vented 276 72 25.4 24.5 Hub 5
HX - HZ 1976 - 80 With

WB Utility, Panel Van 1980 - 85 Studs & Cups

HQ - HJ 1971 - 76 R 018 3 Solid 292 90 15.9 14.7 72 5

HX - HZ 1976 - 80
WB Utility, Panel Van 1980 - 85
The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 89
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV ASTRA VXR

2L Turbo 2005 - on F 2034 3 3 Vented 321 44 28 26 70 5
R 2035 3 3 Solid 278 42.2 10 8 65 5

HSV AWD
Coupe 4 05/04 - on F 42022 3 Vented 336 45.2 32 30 71.5 5
Avalanche Wagon
Avalanche XUV Dual Cab Ute 05/04 - on R 4049 3 Vented 315 71 18 16 70 5
All VY series II on

HSV - CLUBSPORT
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5
VP inc. Clubsport 5000i 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 045 3 3 Vented 280 67 20 19 70 5
VR (Sedan & Wagon) 1993 - 95 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VS 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VT 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5
VT 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VX 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5
VX 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY II 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY II Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5

90 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - CLUBSPORT
VZ 8/04 - 1/05 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VZ (Not Suitable for use with OE hat/bell) 8/04 - 1/05 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VZ II 1/05 - 8/06 F 52018 3 Vented 350 83 32 30 71.6 5
Performance Brakes - R 42019 3 Vented 332 75.2 24 22 70.1 5
AP 4 Piston Calipers
VZ II (Not Suitable for use with OE hat/bell) 1/05 - 8/06 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5

HSV - CLUBSPORT R8 inc. tourer

VX 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VX Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY II Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ Premium Brakes 8/04 - 1/05 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ (Not Suitable for use with OE hat/bell) 8/04 - 1/05 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VZ II 1/05 - 8/06 F 52018 3 Vented 350 83 32 30 71.6 5
Performance Brakes - R 42019 3 Vented 332 75.2 24 22 70.1 5
AP 4 Piston Calipers
VZ II (Not Suitable for use with OE hat/bell) 1/05 - 8/06 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VE (LS2 V8), VE (LS3 V8) 2006 - 09 F 42030 3 3 Vented 365 54 32 30 67.4 5
inc. Clubsport R8 Tourer R 42031 3 Vented 350 61.5 26 24 67.4 5
VE2 (LS3 V8) 9/09 - on F 42030 3 3 Vented 365 54 32 30 67.4 5
inc. Clubsport R8 Tourer R 42031 3 Vented 350 61.5 26 24 67.4 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 91
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - HRT & HSVDT CLUBSPORT

VZ Special Edition 1/05 - 8/06 F 52018 3 Vented 350 83 32 30 71.6 5
Performance Brakes - R 42019 3 Vented 332 75.2 24 22 70.1 5
AP 4 Piston Calipers
VZ Special Edition 1/05 - 8/06 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers (Not Suitable for use with OE hat/bell) R 42025 3 Vented 343 76.3 26 24 70.1 5

HSV - COUPE LE
VY II 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY II Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5

HSV - FORMULA
VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - GRANGE
VS 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
WH 6/99 - 03 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5
WH Performance Brakes 6/99 - 03 F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
WH Premium Brakes 6/99 - 03 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
WK Performance Brakes 2004 F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
WK Premium Brakes 2004 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
WL 2005 - 06 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
WL Premium Brakes 2005 - 06 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VE (LS2 V8), VE (LS3 V8) 2006 - 09 F 42030 3 3 Vented 365 54 32 30 67.4 5
R 42031 3 Vented 350 61.5 26 24 67.4 5
VE2 (LS3 V8) 9/09 - on F 42030 3 3 Vented 365 54 32 30 67.4 5
R 42031 3 Vented 350 61.5 26 24 67.4 5

92 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - GTO COUPE

(V2) - 2 Door Coupe 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
(V2) - 2 Door Coupe 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Premium Brakes
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ 8/04 - 1/05 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VZ (Not Suitable for use with OE hat/bell) 8/04 - 1/05 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5

HSV - GTO LE
VZ Special Edition 8/04 - 8/06 F 52018 3 Vented 350 83 32 30 71.6 5
Performance Brakes - R 42019 3 Vented 332 75.2 24 22 70.1 5
AP 4 Piston Calipers
VZ Special Edition 1/05 - 8/06 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers (Not Suitable for use with OE hat/bell) R 42025 3 Vented 343 76.3 26 24 70.1 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 93
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - GTS
VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 045 3 3 Vented 280 67 20 19 70 5
VR 1993 - 95 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VS 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VT 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VT Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VX Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY (Not Suitable for use with OE hat/bell) 10/02 - 8/04 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VY II (Not Suitable for use with OE hat/bell) 10/02 - 8/04 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VE (LS2 V8), VE (LS3 V8) 2006 - 09 F 42030 3 3 Vented 365 54 32 30 67.4 5
R 42031 3 Vented 350 61.5 26 24 67.4 5
VE2 (LS3 V8) 4 Piston Caliper 9/09 - on 42030 3 3 Vented 365 54 32 30 67.4 5
F
**(Front not suitable for SV Enhanced 6 piston caliper) R 42031 3 Vented 350 61.5 26 24 67.4 5

HSV - GTS-R
VS 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5

HSV - GTS COUPE

(V2) - 2 Door Coupe 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
(V2) - 2 Door Coupe 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Premium Brakes R 4049 3 Vented 315 71 18 16 70 5
Harrop 4 Piston Calipers
VY (Not Suitable for use with OE hat/bell) 10/02 - 8/04 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VZ (Not Suitable for use with OE hat/bell) 8/04 - on F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5

94 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - MALOO
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5
VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5
VR 1993 - 95 F 046 3 3 3 Vented 328 82 28 25 70 5
R 016 3 3 Solid 279 83 10.5 8.5 70 5
VS 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 016 3 3 Solid 279 83 10.5 8.5 70 5
VU 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Vented 286 78.6 16 14 70 5
VU 9/97 - 10/02 F 4048 3 3 Solid 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VU Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY II 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VY II Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ 8/04 - 1/05 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VZ Premium Brakes 8/04 - 1/05 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ II 1/05 - 8/06 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 95
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - MALOO R8
VU 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VU Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY + VY II Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ 8/04 - 1/05 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers
VZ Premium Brakes 8/04 - 1/05 F 5055 3 Vented 343 83 32 29 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ (Not Suitable for use with OE hat/bell) 8/04 - 1/05 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VZ II 1/05 - 8/06 F 52018 3 Vented 350 83 32 30 71.6 5
Performance Brakes - R 42019 3 Vented 332 75.2 24 22 70.1 5
AP 4 Piston Calipers
VZ II (Not Suitable for use with OE hat/bell) 1/05 - 8/06 F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers R 42025 3 Vented 343 76.3 26 24 70.1 5
VE (LS2 V8), VE (LS3 V8) 2006 - 09 F 42030 3 3 Vented 365 54 32 30 67.4 5
VE2 (LS3 V8) 9/09 - on R 42031 3 Vented 350 61.5 26 24 67.4 5

HSV - MANTA
VS (Sedan & Wagon) 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VT 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5
VT 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
Performance Brakes - R 4049 3 Vented 315 71 18 16 70 5
PBR 2 Piston Calipers

HSV - NITRON
VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - PLUS6
VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 045 3 3 Vented 280 67 20 19 70 5

96 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - PLUS8
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 045 3 3 Vented 280 67 20 19 70 5

HSV - SENATOR
VP inc. Senator 5000i 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 045
3 3 Vented 280 67 20 19 70 5
VR 1993 - 95 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VS (Sedan & Wagon) 1995 - 97 F 046 3 3 3 Vented 328 82 28 25 70 5
R 047 3 3 Vented 280 86 20 19 70 5
VT 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5
VT Performance Brakes 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VT Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VX Standard Brakes 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
R 041 3 3 3 Solid 286 78.6 16 14 70 5
VX Performance Brakes 9/97 - 10/02 F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VX Premium Brakes 9/97 - 10/02 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY Performance Brakes 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY II Performance Brakes 10/02 - 8/04 F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VY II Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ Performance Brakes 8/04 - on F 4048 3 3 Vented 330 83 32 29 71.5 5
PBR 2 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5
VZ AP 6 Piston Calipers 8/04 - on F 52024 3 Vented 362 83 32 30 71.5 5
(Not Suitable for use with OE hat/bell) R 42025 3 Vented 343 76.3 26 24 70.1 5
VE (LS2 V8), VE (LS3 V8) 2006 - 09 F 42030 3 3 Vented 365 54 32 30 67.4 5
VE2 (LS3 V8) 9/09 - on R 42031 3 Vented 350 61.5 26 24 67.4 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 97
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - SIGNATURE COUPE

VZ Special Edition 8/04 - on F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers (Not Suitable for use with OE hat/bell) R 42025 3 Vented 343 76.3 26 24 70.1 5

HSV - SKAIFE SENATOR

VZ Special Edition 1/05 - on F 52018 3 Vented 350 83 32 30 71.6 5
Performance Brakes - R 42019 3 Vented 332 75.2 24 22 70.1 5
AP 4 Piston Calipers

HSV - SPORTS WAGON

VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - SS GROUP A
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - STATESMAN SV93

VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - SV LE
VN (Sedan & Wagon) 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - SV300
VX Premium Brakes 10/02 - 8/04 F 5055 3 Vented 343 82.5 32 30 71.5 5
Harrop 4 Piston Calipers R 4049 3 Vented 315 71 18 16 70 5

HSV - SV3800
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - SV5000
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - SV6000
VZ Special Edition 8/04 -on F 52024 3 Vented 362 83 32 30 71.5 5
AP 6 Piston Calipers (Not Suitable for use with OE hat/bell) R 42025 3 Vented 343 76.3 26 24 70.1 5

98 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - HSV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HSV - SV89
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 020 3 3 Vented 278 83.6 20 19 70 5

HSV - SV91
VN 1988 - 91 F 019 3 Vented 327 82 28 25 HUB 5
R 045 3 3 Vented 280 67 20 19 70 5
VP 1991 - 93 F 019 3 Vented 327 82 28 25 HUB 5
R 045 3 3 Vented 280 67 20 19 70 5

HSV - XU6
VX 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5

HSV - XU8
VT 9/97 - 10/02 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
Standard Brakes R 041 3 3 3 Solid 286 78.6 16 14 70 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 99
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MONARO
VT:VY CV6 & CV8 12/2001 - 04 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
(V2) - 2 Door Coupe R 041 3 3 3 Solid 286 78.6 16 14 70 5
VZ CV8 GEN III V8 250kW 2005 - 06 F 2020™ 3 3 3 3 Vented 320 83 32 30 71.6 5
except V5B - model 37 coupe R 2021™ 3 3 3 Vented 286 80 18 16 70 5
VZ V5B model 37 coupe 2005 - 06 F
with HSV brake option R

NOVA
LE, LF 1989 - 10/94 F 701 3 Solid 243 48 13.5 12.5 54 4
1989 - 9/92 F 704 3 Vented 238 48 18 17 54 4
6/91 - 94 F 708 3 Vented 258 48 22 20 54 4
LE Opt., LF GS ( Rear ) 1989 - 10/94 R 703 3 Solid 242 37 9 8 54 4
LG, GS, SLX 10/94 - 4/96 F 709 3 Vented 255 48.5 22 20 55 4
R 710 3 Solid 266 37 9 8 55 4

Piazza
PART NOT AVAILABLE
Piazza (Impulse) 1983 - 89 F 811 3 Vented 250
REFERENCE ONLY 32 18 16.6 68 4
R 812 3REFERENCE
PART NOT AVAILABLE
ONLY Vented 266 60 18 16.6 57 4

TIGRA
1.3L CDTi, 1.4L, 1.8L 4/2001 - 06 F 847 3 Vented 260 41.2 24 21 60 4
Convertible R 849 3 Solid 240 41 10 8 57 4

TORANA / SUNBIRD
HB, TA, LC, LJ, 4 Cyl 1969 - 72 F 009 3 Solid 215 28.5 10 9 61 4
LC, LJ 6 Cyl 1969 - 72 F 008 3 Solid 256 60 12.7 12 72 5
LJ XU-1 1972 - 73 F 004 3 Solid 256 60 15.7 14.7 72 5
LH, LX, UC 1974 - 79 F 010 3 Solid 256 77 16 14.3 Hub 5

Complete with Studs and Cups

A9X 1977 - 78 F 014 3 3 Vented 276 72 25.4 24.5 Hub 5

100 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

VECTRA
JR, JS, JSII - 2.0L, 2.2L, 2.5L 6/97 - 2/03 F 825 3 Vented 288 42 25 22 70 5
(CD & GL Sedans) R 826 3 Solid 286 69 10 8 65.5 5
ZC 2.2L 2/03 - 05 F 2820 3 Vented 285 43 25 22 70 5
ZC V6 up to VIN No. 38047796 2003 - 05 F 2817 3 Vented 302 46 28 25 70 5
ZC V6 after VIN No. 38047796 2003 - 05 F 2819 3 3 Vented 314 46 28 25 70 5
ZC V6 rear suits all models 2003 - 05 R 2818 3 Vented 292 42 20 18 66 5

ZAFIRA
TT 2.2 Litre DOHC 6/2001 - on F 815 3 Vented 280 42 25 22 70 5
4D Wagon R 816 3 Solid 264 42 10 8 65 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 101
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - commercial / 4wd C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

COMBO
SB Van 2/96 - 2000 F 821 3 Vented 236 41 20 17 60 4
XC VAN 4/01 - 05 F 847 3 Vented 260 41.2 24 21 60 4
2005 - on F 2036 3 Vented 280 42.3 25 23 60 4

DROVER
QB 4WD 3/85 - 87 F 510 3 Solid 290 46.5 10 8.5 107 5

FRontera 4 X 4
2.0i with & without ABS 3/95 - on F 840 Vented 280 36 26 24.6 87.5 6
Sport 4 X 4 UT 10/95 - 6/99
S & SE - V6 & 4Cyl 2/99 - on
R 841 Vented 313 81 18 16.6 101 6

JACKAROO / TROOPER - ISUZU (GM)

Monterey U8 3.5 Litre ABS 2/98 on F 840 Vented 280 36 26 24.6 87.5 6
R 841 Vented 313 81 18 16.6 101 6
UBS 13, UBS 52 11/81 - 85 F 031 Solid 259 37.5 12.5 11.1 80 6
PART NOT AVAILABLE
REFERENCE ONLY

UBS 16, UBS 521, 522 8/85 - 88 F 032 Vented 250 35 18 16.7 80 6
UBS 17, UBS 55 1988 - 91 F 033 Vented 257 36 22 20.6 88 6
UBS 16, 17, 52, 55 1987 - 91 R 034 Solid 265 47 12 10.6 97 6
UBS 25 1992 - on F 840 Vented 280 36 26 24.6 87.5 6
US / U8 : S & SE, Monterey 2/98 - on R 841 Vented 313 81 18 16.6 101 6

PANTHER - ISUZU (GM)

PART NOT AVAILABLE
Panther F 844 3 Vented 231
REFERENCE ONLY 35 22 20.6 63 4

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

102 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HOLDEN - commercial / 4wd C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

RODEO / COLORADO
KB, KBD, 2, 4 Series 1980 - 82 F 030 3 Solid 250 35 18 17 80 6
KB, KBD, 2, 4 Series 1982 - 84 F 031
PART NOT AVAILABLE
REFERENCE ONLY Solid 259 37.5 12.5 11 80 6
KB 28, 29, 43, 49, Late 84 - 88 F 032 3 Vented 250 35 18 16.7 80 6
KBD 27, 28, 43, 47
TFR, TFS17, 54, G3, G6 1988 - 94 F 033 3 Vented 257 36 22 20.6 88 6
R7 4x2 2.6, 2.8 Litre 1996 - 02
R9 4x2, 4x4 2.6, 2.8 Litre 1996 - 02
Rodeo - Sth Africa (special) 1996 - 02 F 2033 Vented 252 36 22 20.6 88 6
R7 & R9 - V6 3.2 Litre 1997 - 02 F 840 Vented 280 36 26 24.6 87.5 6
4x2 & 4x4 versions
RA V6 PFI 4X2 + all 4X4 12/2002 - 08 F 2840 Vented 280 40.5 27 25.6 88 6
Hi-ride Suspension. (Torsion Bar)

RA 2.4L 4cyl, 3.0L Turbo Diesel 11/02 - 08 F 2839 Vented 256 40.1 26 24.6 88 6
Non Hi-ride Suspension (Coil Front)
RC V6 PFI 4X2 + all 4X4 2008 - on F 2840 Vented 280 40.5 27 25.6 88 6
Hi-ride Suspension. (Torsion Bar Front)

RC 2.4L 4cyl, 3.0L Turbo Diesel 2008 - on F 2839 Vented 256 40.1 26 24.6 88 6
Non Hi-ride Suspension (Coil Front)

SCURRY
NB 7/85 - 87 F 012 3 Solid 215 33.5 10 8 86 4

SHUTTLE
WFR 1982 - 84 F 031
PART NOT AVAILABLE
Solid 259 37.5 12.5 11 80 6
REFERENCE ONLY

WFR 1982 - 90 F 032 3 Vented 250 35 18 16.7 80 6

SUBURBAN
1500 (K8) LS & LT 5.7L 2/98 - 00 F 773 Vented 295 63.5 32.5 30.8 78.7 6
PART NOT AVAILABLE
REFERENCE ONLY

2500 (K8) LS & LT 6.5L 2/98 - 00 F 774 Vented 317.5 70 33 30.8 137.2 8

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 103
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HONDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ACCORD
SJ 1600, 1602 1976 - 81 F 189 3 Solid 231 41 12 10.5 86 4
SY, SZ 1602 1981 - 83 F 190 3 Solid 231 50 12 10 61 4
SY, SZ Hatchback 4-Door 5/82 - 83 F 195 3 Vented 231 50 17 15 61 4
AC, AD, 1600, 1800 1984 - 86 F 196 3 Vented 242 50 19 17 61 4
CA4 SOHC, CA5
CA4 2000 AD, CA4 CXi 1986 - 89 F 184 3 Vented 262 51 21 19 64 4
CA4, CA5 1988 - on R 198 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 239 48.2 10 8 61 4
CB 2WS, CC Sedan/Wagon 11/89 - 94 R 471 3 Solid 260 49 10 8 64 4
CB 4WS 11/89 - 94 R 481 3 Solid 260 43 10 8 64 4
2.2i (CB75/76, CC7, CE9) 1990 - 98 F 179 3 Vented 282 34 25 23 92 4
Acura Vigor 1992 - 94
Acura TL 2.5L Sedan 1995 - on
1.8i (CE7-auto, 2.0i (CE8-auto) 1996 - 9/98
PART NOT AVAILABLE
CB, CC Wagon, Aerodeck 1992 - 94 F 472 3REFERENCE
Vented
ONLY 282 34 25 23 92 4
CCB, CC Sedan Only 11/89 - 94 F 470 3 Vented 260 34 23 21 92 4
CD 1994 - 97
Note: Check dimensions R 471 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 260 49 10 8 64 4
PART NOT AVAILABLE
CE Wagon 6/94 - on F 472 3REFERENCE
Vented
ONLY 282 34 25 23 92 4
R 471 3 Solid 260 49 10 8 64 4
CG V6-L 2.3L + 3.0L 1998 - 04 F 488 3 3 Vented 282 47 23 21 64 5
R 489 3 Solid 260 48 9 8 64 5
CG2 V6 J30A1 (UK Model) 7/98 - 2002 F 405 3 Vented 282 47 28 26 64 5
R 2.2i (VTEC) 2000 - on F 476 3 3 Vented 300 47.5 28 26 70 5
V 4DR (USA + Europe) 2000 - 2003 F 2506 3 3 Vented 282 48 25 23 64 5
2.4L + 3.0L V6 VTEC 2004 - on F 488 3 3 Vented 282 47 23 21 64 5
EURO.2.4L i-VTEC 2004 - on F 2510 3 3 3 Vented 300 48 28 26 64 5
Rear disc fits both 2004 models R 2511 3 Solid 260 49 9 8 64 5
( rear hat diameter is 154 mm )
EURO V6 2005 - on F 2514 3 3 Vented 282 47 28 26 64 4

104 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HONDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CIVIC
SBI, SC Sedan 1200 1973 - 79 F 188 3 Solid 225 44.5 10 9 92 4
SF Hatchback 1200 1978 - 79
SB, SE Sedan, Wagon 1500 1975 - 78
SL, SS, SR, ST, VC - Hatch 1979 - 83 F 193 3 Solid 215 50 11 9 61 4
WC 1300 Wagon 1980 - 81
SR, ST Wagon 1982 - 83
1.3, 1.5L (AH-AK), CRX 1984 - 87 F 178 3 Vented 231 43.8 17 15 61 4
1.5 Hatch + Wagon 2WD/4WD (USA) 1984 - 87
1.4 (EC9-ED2), HF (USA) 1988 - 91
1.3 16V (EG33) 1991 - 94
AA 1984 - 87 F 191 3 Solid 231 44 12 10 61 4
PART NOT AVAILABLE
CITY VF 1984 - 86 F 194 3
REFERENCE ONLY Solid 212 40 10 8 61 4
ED 4WD Wagon 3/88 - 5/89 F 187 3 Vented 242 44.5 19 17 61 4
ED 4-Door 1988 - 91
EG GL, GLi, VEi, Sedan, 11/91 - 94 F 473 3 Vented 240 45 21 19 61 4
DX/HX Coupe/Sedan (USA) 1993 - on
Del Sol, Wagovan (USA)
EE9, EF, EG 1.6i VTEC VTi 11/91 - 95 F 474 3 3 Vented 262 45 21 19 64 4
EH1 4WD, EJ1 Coupe 1.6i
Coupe /Sedan EX/LX (USA) 1990 - 95
MA8 1.4i, MA9, MB1/4 12/94 - on
MB2, MB3, MB7/8/9, MC1 1997 - on
MC3 2.0TDi, EJ6/8
EK 3 Door
R 475 3 3 Solid 239 48 9 8 61 4
EX - with ABS 1993 - 95 F 474 3 3 Vented 262 45 21 19 64 4
R 475 3 3 Solid 239 48 9 8 61 4
DX & HX, 1996 - 2000 F 473 3 Vented 240 45 21 19 61 4
EX 1996 - 2000 F 474 3 3 Vented 262 45 21 19 64 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 105
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HONDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CIVIC - continued
Si 1999 - 2000 F 474 3 3 Vented 262 45 21 19 64 4
R 475 3 3 Solid 239 48 9 8 61 4
all models 2001 - 2005 F 474 3 3 Vented 262 45 21 19 64 4
Civic 1.7L SOHC 4/5dr 2001 - on R 2502 3 Solid 260 48 9 8 61 4
1.8 SOHC Vti & Vti-L 2006 - ON F 488 3 3 Vented 282 47 23 21 64 5
2.0L DOHC SPORT R 438 3 Solid 260 42 9 8 64 5
2.0i SPORT VI Hatchback 01/04 - 12/05 R 2515 3 3 Solid 259.5 49 10 8 64 5
2.0L Type-R EP3 (UK) 2001 - 06 F 2500 3 3 3 Vented 300 47.5 25 23 64 5
VI Hatchback (EU_, EP_) R 2515 3 3 Solid 259.5 49 10 8 64 5
FD2 -R 2007 - on F 2518 3 3 Vented 320 62 25 23 64 5
R 2519 3 3 Solid 282 49 9 8 64 5
FN2 Type-R 2007 - on F 2500 3 3 3 Vented 300 47.5 25 23 64 5
R 438 3 Solid 260 42 9 8 64 5

106 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HONDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

concerto
EXI, Reprise, EXI-Reprise 5/91 - on F 187 3 Vented 242 44.5 19 17 61 4
R 182 3 Solid 239 48 10 8 61 4

CR-V
2.0i 16V (RD1) 4Dr Wagon 10/97 - 10/02 F 478 3 3 Vented 282 47 23 21 70 5
2.0L, 2.3L 4Dr Wagon 2002 - 6/05 F 488 3 3 Vented 282 47 23 21 64 5
R 2503 3 Solid 282 61 9 7.5 64 5
2.0L, 2.4L, 2.2L Diesel 6/05 - 10/08 F 2500 3 3 3 Vented 300 47.5 25 23 64 5
**Check Dimensions** F 476 3 3 Vented 300 47.5 28 26 70 5

HR-V
1.6i 16V (GH1/2) 1999 - 04 F 478 3 3 Vented 282 47 23 21 70 5

CRX
ED 1.6 litre 2-Door DX-Si 1987 - 91 F 187 3 Vented 242 44.5 19 17 61 4
R 182 3 Solid 239 48 10 8 61 4
1500/1600 Si 1990 - 91 F 187 3 Vented 242 44.5 19 17 61 4
R 475 3 3 Solid 239 48 9 8 61 4
EE8 VTEC 1.6L 1989 - 92 F 474 3 3 Vented 262 45 21 19 64 4
EG21 VTi, EH61 ESi 1.6L 1992 - 97
EG VTec 6/92 - 12/98
R 475 3 3 Solid 239 48 9 8 61 4

INTEGRA
PART NOT AVAILABLE
Quint 1.6 (AV) 1984 - 86 F 178 3REFERENCE
ONLY Vented 231 43.8 17 15 61 4
DA3, DA4, 1.6L 1986 - 88 F 187 3 Vented 242 44.5 19 17 61 4
R 192 3 Solid 239 27.5 10 8 48 4
1.8L DOHC 16V 1989 - 94 F 474 3 3 Vented 262 45 21 19 64 4
1.8L GSi, VTi - R 1993 - 98
Acura Integra, 2.0L GSi 1990 - on
R 475 3 3 Solid 239 48 9 8 61 4
TYPE-R 2000 - 01 F 478 3 3 Vented 282 47 23 21 70 5
R 477 3 Solid 260 48 9 8 64 5
Integra Type-R DC5 2001 - on F 2508 3 3 3 Vented 300 57.8 25 23 64 5
Japanese domestic
Brembo Caliper Models
TYPE-S 2002 - on F 2500 3 3 3 Vented 300 47.5 25 23 64 5
TYPE-R - Australian Model

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 107
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HONDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

JAZZ
GLi 1.3L SOHC 10/2002 - on F 2504 3 Vented 240 39 21 19 61 4

LEGEND
KA2 4-Door Sedan 1986 - 87 F 186 3 Vented 262 51.5 21 19 64 4
KA3 4D Sedan, KA4 2D Coupe 11/87 - 91 F 185 3 Vented 282 51 21 19 64 4
R 199 3 Solid 260 43 10 8 64 4
KA7, KA8, KA9 3/91 - 95 F 478 3 3 Vented 282 47 23 21 70 5
3.5L V6 15” wheels 1996 - on
R 479 3 3 Solid 282 61 9 7.5 70 5
3.5L V6 16” wheels 1996 - on F 476 3 3 Vented 300 47.5 28 26 70 5
R 499 3 Solid 282 61 12 10 64 5

NSX
NSX 4 Auto 1991 - 98 F 484 3 3 Vented 282 36 28 26 70 5
NSX-T 5 Manual R 485 3 Vented 282 32.5 21 19 69 5
6 Speed Manual 4/97 - on F 486 3 3 Vented 298 36.5 28 26 70 5
NSX, NSX-T R 487 3 3 Vented 303 32.5 23 21 64 5

PRELUDE
SU, SN 1979 - 82 F 190 3 Solid 231 50 12 10 61 4
AB, ALB 1800 1983 - 87 F 197 3 Vented 231 50 19 17 61 4
BA3 1986 - 87 F 196 3 Vented 241 50 19 17 61 4
AB, BA3 Non-ABS 1983 - 87 R 183 3 Solid 239 45 10 8 Hub 4
BA4, Si, SE 1988 - 91 F 184 3 Vented 262 51 21 19 64 4
10/87 - 91 R 198 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 239 48.2 10 8 61 4
V-TEC 1992 - 96 F 200 3 3 Vented 282 47 23 21 64 4
R 481 3 Solid 260 43 10 8 64 4
5-lug 1997 - 2001 F 478 3 3 Vented 282 47 23 21 70 5
R 438 3 Solid 260 42 9 8 64 5
BB incl. 4WS 12/91 - 94 F 480 3 Vented 260 47 23 21 64 4
R 481 3 Solid 260 43 10 8 64 4
VTi-S & Si 2/94 - on F 480 3 Vented 260 47 23 21 64 4
Stepped hat R 481 3 Solid 260 43 10 8 64 4
Straight hat R 2513 3 Solid 260 42 9 8 64 4
VTi-R 2/94 - 97 F 200 3 3 Vented 282 47 23 21 64 4
R 481 3 Solid 260 43 10 8 64 4
2.2L DOHC VTi-R 1997 - 2001 F 478 3 3 Vented 282 47 23 21 70 5
R 438 3 Solid 260 42 9 8 64 5

108 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HONDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

S 2000
S 2000 1999 - 03 F 482 3 3 Vented 300 40 25 23 70 5
R 483 3 3 Solid 282 40 12 10 64 5
all models 2003 - 05 F 488 3 3 Vented 282 47 23 21 64 5
R 2503 3 Solid 282 61 9 7.5 64 5

ODYSSEY
Odyssey - 4 Door Wagon 6/95 - 2000 F 478 3 3 Vented 282 47 23 21 70 5
R 479 3 3 Solid 282 61 9 7.5 70 5
Odyssey 2.3L + V6 2000 - 05 F 476 3 3 Vented 300 47.5 28 26 70 5
R 2503 3 Solid 282 61 9 7.5 64 5

PASSPORT
3 Vented 280 36 26 24.6 88 6
all models 1996 - 01 F 842
841 3 Vented 313 80.6 18.1 16.6 101 6
R

PILOT
all models 2003 - 05 F 476 3 3 Vented 300 47.5 28 26 70 5

SHUTTLE
2.3i (RA1), 2.3i ES/LS (RA3) 6/95 - on F 478 3 3 Vented 282 47 23 21 70 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 109
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HUMBER C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Snipe, Hawk Series II, III, IV 1960 - 69 F 094 3 Solid 290 39 12.75 11 79.5 5

HUMMER
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

HUMMER
H2 - 6.0L All wheen drive 09/02 - 09/04 F 2048 Vented 325 89.5 38 36.5 118.2 8
H2 - 6.0L SUT pickup 09/04 - on R 2049 Vented 330 85.6 29 26.5 118.2 8
H3 - 3.5L 04/05 - on F 2054 Vented 315 70.4 28 26.5 100.7 6
H3 - 3.7L AWD 09/06 - on
H3 - 5.3L V8 10/08 - on
R 2055 Solid 312 67.9 12 10.5 101 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

110 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HYUNDAI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ACCENT
1.3i 12V, 1.5i 12V, 1.5i 16V 1994 - 99 F 451 3 Vented 242 40.5 19 17.7 86 4
GL, GLS, Sprint, Lifesyle 1999 - 11/05 F 450 3 Vented 241 52 19 17.7 63 4

COUPE
FX, SX, SFX, Tiburon 8/96 - 98 F 453 3 Vented 257 34 22 20 86 4
R 457 3 Solid 257 40.5 10 8 76 4
Coupe, Turbulence 8/98 - on F 456 3 3 Vented 257 45 24 22.4 69 4
Scoupe 1.5i, incl. USA 1989 - 4/95 F 451 3 Vented 242 40.5 19 17.7 86 4

ELANTRA / LANTRA / LAVITA

J1 & J2, incl. 1.9L Diesel, 5/91 - 5/98 F 453 3 Vented 257 34 22 20 86 4
5/91 - 8/95 R 459 3 Solid 257 40 10 8 90 4
J2 5/98 - on F 456 3 3 Vented 257 45 24 22.4 69 4
9/95 - on R 457 3 Solid 257 40 10 8 76 4
Elantra XD GL 1.8L, GLS 2.0L 5/2000 - on F 456 3 3 Vented 257 45 24 22.4 69 4
Lavita, (Hatchback & Sedan)
R 457 3 Solid 257 40 10 8 76 4

EXCEL
X1 11/85 - 1/88 F 215 3 Solid 228 40 13 11.5 86 4
X1, X3, XZ, XL Van, S Coupe 1/88 - 00 F 451 3 Vented 242 40.5 19 17.7 86 4
Pony/Excel 1.3-1.5i (MU) 1989 - 94

GETZ
(TB) All - Non ABS 7/2002 - on F 2450 3 Vented 241 48 19 17 62 4
(TB) All - With ABS 7/2002 - on F 2451 3 Vented 256 48 19 17 69 4

GRANDUER
XG - 4D Sedan V6 DOHC 7/99 - on F 460 3 Vented 276 46.5 26 24 69 5
R 461 3 Solid 262 66 10 8.4 76 5

i30
All Models 2007 - on F 2464 3 Vented 280 47.5 26 24 69 5
2.0L Petrol, 1.6 CRDi R 2459 3 Solid 262 61 10 8.4 76 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 111
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HYUNDAI - sonata C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

i-LOAD / i-MAX
2.4L, 2.5L CRDI 2007 - on F 2460 3 3 Vented 300 52.5 30 28.4 96.2 6
R 2461 Vented 320 82.6 18 16.4 96.2 6

SONATA
Y1, Y2 Sonica all models 1/89 - 4/98 F 452 3 Vented 257 45.5 22 20 69 4
Y1 ( Rear ) 1/89 - 94 R 454 3 Solid 263 46 12 10 90 4
Y2 ( Rear ) 7/93 - 4/98 R 455 3 Solid 260 59.5 12 10.5 90 4
Y3 all models 4/98 - 4/01 F 456 3 3 Vented 257 45 24 22.4 69 4
R 458 3 Solid 262 61 10 8 76 4
EF-B (GL) - 2.3L, 2.7L V6 4/01 - on F 463 3 Vented 257 47.5 25 22.4 69 4
R 458 3 Solid 262 61 10 8 76 4
2.4L GL + 2.7L V6 2004 - 06 F 2458 3 Vented 257 47 24.5 22.4 64 4
NF 3.3L V6 2006 - on F 2456 3 3 Vented 300 47.5 28 26 69 5
R 2457 3 Solid 284 54.6 10 8 76 5

TIBURON
2.7L V6 + 2.0L : GT 9/01 - on F 468 3 3 3 Vented 280 48 26 22.4 69 5
Coupe 1.6S, 2.0SE, 2.7L
R 469 3 3 Solid 258 45 10 8 75.5 5

TRAJET
GL, GLS V6 2.7L Wagon 3/00 - on F 464 3 Vented 276 47 26 24 69 5
R 465 3 Solid 284 61 10 8.4 76 5

SANTA FE
GL 2.4, GL/GLS 2.7L V6 11/00 - 8/06 F 2452 3 Vented 294 46 26 24 69 5
( Rear for GLS V6 only ) R 465 3 Solid 284 61 10 8.4 76 5
All models 9/06 - on F 2462 Vented 298 49.5 28 26.4 69 5
R 2463 Solid 302 72 11 9.4 69 5

TUCSON
All Models 8/04 - on F 468 3 3 3 Vented 280 48 26 22.4 69 5
AWD Only R 465 3 Solid 284 61 10 8.4 76 5
2WD Only R TBA

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

112 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
HYUNDAI - 4WD / SUV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

TERRACAN 4WD
3.5 V6 + 2.9L TCi Diesel 2001 - 03 F 466 3 Vented 280 43 27 25.4 87 6
3.5 V6 + 2.9L TCi Diesel 12/03 - on F 2454 Vented 303 43 28 26.4 87 6
rear suits all models R 467 Vented 315 86.5 20 18.4 108 6

GALLOPER 4WD
V6 3.0L LWB 9/88 - 92 F 2229 Vented 276 45.5 22 20.4 87 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 113
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
ISUZU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

JACKAROO / TROOPER
Monterey U8 3.5 Litre ABS 2/98 on F 840 Vented 280 36 26 24.6 87.5 6
R 841 Vented 313 81 18 16.6 101 6
UBS 13, UBS 52 11/81 - 85 F 031 3 Solid 259 37.5 12.5 11.1 80 6
UBS 16, UBS 521, 522 8/85 - 88 F 032 3 Vented 250 35 18 16.7 80 6
UBS 17, UBS 55 1988 - 91 F 033 3 Vented 257 36 22 20.6 88 6
UBS 16, 17, 52, 55 1987 - 91 R 034 3 Solid 265 47 12 10.6 97 6
UBS 25 without ABS 1992 - on F 840 Vented 280 36 26 24.6 87.5 6
US / U8 : S & SE, Monterey 2/98 - on R 841 Vented 313 81 18 16.6 101 6

PANTHER- ISUZU (GM)

PART NOT AVAILABLE
Panther F 844 3 Vented 231
REFERENCE ONLY 35 22 20.6 63 4

RODEO
KB, KBD, 2, 4 Series 1980 - 82 F 030 3 Solid 250 35 18 17 80 6
KB, KBD, 2, 4 Series 1982 - 84 F 031 3 Solid 259 37.5 12.5 11 80 6
KB 28, 29, 43, 49, Late 84 - 88 F 032 3 Vented 250 35 18 16.7 80 6
KBD 27, 28, 43, 47
TFR, TFS17, 54, G3, G6 1988 - 94 F 033 3 Vented 257 36 22 20.6 88 6
R7 4x2 2.6, 2.8 Litre 1996 - 02
R9 4x2, 4x4 2.6, 2.8 Litre 1996 - 02
R7 & R9 - V6 3.2 Litre 1997 - 02 F 840 Vented 280 36 26 24.6 87.5 6
4x2 & 4x4 versions
RA V6 PFI 4X2 + all 4X4 12/2002 - on F 2840 Vented 280 40.5 27 25.6 88 6
Hi-ride Suspension. (Torsion Bar)

RA 2.4L 4cyl, 3.0L Turbo Diesel 11/02 - on F 2839 Vented 256 40.1 26 24.6 88 6
Non Hi-ride Suspension (Coil Front)

D-Max
2.4L, 2.5D, 3.0DiTD, 3.5L V6 5/02 - on F 2840 Vented 280 40.5 27 25.6 88 6
Hi-ride Suspension. (Torsion Bar)
2.4L, 2.5D, 3.0DiTD, 3.5L V6 5/02 - on F 2839 Vented 256 40.1 26 24.6 88 6
Non Hi-ride Suspension (Coil Front)
2.5DiTD, 3.0D 1/07 - on F 2840 Vented 280 40.5 27 25.6 88 6
Hi-ride Suspension. (Torsion Bar)
2.5DiTD, 3.0D 1/07 - on F 2839 Vented 256 40.1 26 24.6 88 6

Non Hi-ride Suspension (Coil Front)

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

114 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
JAGUAR C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MK series
Mk 2 - all Models 1959 - 67 F 072 3 Solid 280 51.5 9.75 8.5 82.5 5
Mk 10 1961 - 66
240, 340 1967 - 69
Mk 2 All Models 1959 - 67 R 073 3 Solid 287 53 9.5 8 82.5 5
240, 340 1967 - 69

XJ series
PART NOT AVAILABLE
XJ6 Series 1 1968 - 2/74 F 074
REFERENCE ONLY Solid 283 60 12.5 11.5 82 5
R 075 3 Solid 264 25.5 12.7 11.4 70 4
XJ6 Series 2, 3 1974 - 10/86 F 076 3 Vented 285 60.5 24 22.9 82.7 5
XJS, XJ12 1973 - 1990
R 075 3 Solid 264 25.5 12.7 11.4 70 4
XJ6, XJ12, XJS with Dana Diff. 11/86 - 90 R 075B 3 Solid 262 25.5 12.5 11.4 70 4
XJ40 3.6 11/86 - 90 F 077 Vented 295
PART NOT AVAILABLE
REFERENCE ONLY
67 22.3 21 80 5
R 078 3 Solid 278 68 10 8.8 74 5
XJ40 3.2 & 4.0 Litre 1990 - 1994 F 098 3 Vented 291 66.8 28 27 80 5
R 099 3 Solid 294 67 10 8.8 74 5

E-SERIES
E- 3.8, 4.2 1961 - 68 F 072 3 Solid 280 51.5 9.75 8.5 82.5 5
E- V12 4.2 1968 - 74 F 076 3 Vented 285 60.5 24 22.9 82.7 5
R 075 3 Solid 265 25.5 12.7 11.4 70 4

S-SERIES
S- 3.4, 3.8 1963 - 68 F 072 3 Solid 280 51.5 9.75 8.5 82.5 5
R 075 3 Solid 264 25.5 12.7 11.4 70 4
S- (X200) 3.0i V6 / 4.0i 1999 - on F 2044 Vented 300 43 30 28 71 5
Rear suits all S- (X200) 2045 Vented 288 32.5 20 18.5 64.5 5
R

XKR
XKR 4.0L V8 Turbo 1998 - on F 2046 3 Vented 305 49.5 28 26 73.8 5
2047 3 Vented 305 67.8 20 18.5 73.8 5
R
with Brembo Calipers 2003 - on F 52070 3 Vented 356 50.5 32 30 73.8 5

XK8
4.0L V8 1996 - on F 2046 3 Vented 305 49.5 28 26 73.8 5
2047 3 Vented 305 67.8 20 18.5 73.8 5
R

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 115
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
JEEP / CHRYSLER C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CHEROKEE
CJ Universal 1977 - 78 F 095 3 Vented 298 56 30 28.5 96 5
CJ7, Renegade 9/78 - 81 F 181 3 Vented 298 56.5 22.5 21 95.5 5
all J, MJ & SJ models 1974 - 83 F 180 3 Vented 300 59 32.5 31 101.5 6
J10 1983 - 85 F
CJ8, Hawk 1981 - 85 F 181 3 Vented 298 56.5 22.5 21 95.5 5
Overlander 4 Cyl 1981 - 85
4WD 1988 - 92 F 096 Vented 280 81 24 22.7 72 5

CHEROKEE / WAGONEER / BRAIRWOOD - XJ series

4WD 1990 - 1/92 F 096 Vented 280 81 24 22.7 72 5
all models 2/92 - 98
w/ OE composite disc (82mm) 1990 - 99
w/ OE full cast disc (78mm) 1999 - 01 F 888 Vented 280 78 24.5 22.7 72 5

CHEROKEE / WAGONEER / BRAIRWOOD - KJ series

2.4, 2.5 CRD 09/01 - on F 889 Vented 288 65 28 26 72 5
2.8 CRD 11/02 - on
3.7 V6 08/03 - on
2.8 CRD 11/04 - on

COMANCHE
4WD 1990 - 92 F 096 Vented 280 81 24 22.7 72 5

COMMANDER
all models 2006 F 2530 Vented 328 53 30 28.5 72 5
R 2531 Solid 320 67 14 12.5 72 5

GRAND CHEROKEE
all models 1993 - 98 F 096 Vented 280 81 24 22.7 72 5
R 097 Solid 285 59.5 11 9.5 72 5
all models 1999 - 04 F 540 Vented 305 64 26 24.5 72 5
R 541 Solid 305 75.5 10 8.5 72 5
all except SRT-8 2005 - on F 2530 Vented 328 53 30 28.5 72 5
R 2531 Solid 320 67 14 12.5 72 5
SRT8 2006 - on F 2532 Vented 360 53.5 32 31.8 72 5
R 2533 Solid 350 68.5 28 27.85 72 5

LIBERTY
all models 2002 - 2006 F 889 Vented 288 65 28 26 72 5
With Rear Disc Brakes 2003 - 2006 R 2535 Solid 285 59.6 12 11 72 5

116 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
JEEP / CHRYSLER C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

WRANGLER
w/ OE composite disc (82mm) 1990 - 99 F 096 Vented 280 81 24 22.7 72 5
w/ OE full cast disc (78mm) 1999 - 00 F 888 Vented 280 78 24.5 22.7 72 5
all models - excl. Rubicon 2001 - 06
Drum rear brakes
all models incl Rubicon 2003 - 06 F 888 Vented 280 78 24.5 22.7 72 5
Disc rear brakes R 2535 Solid 285 59.6 12 11 72 5
SRT-8 2005 - 06 F 2532 Vented 360 53.5 32 31.8 72 5
R 2533 Vented 350 68.5 28 27.85 72 5
JK 3.8L V6 + Rubicon 2007 - on F 2536 Vented 302 55.4 28 26.4 72 5
R 2537 Solid 316 76.7 12 10.4 72 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

KIA
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

carnival
Carnival (Suits single piston caliper) 1999 - on F 877 3 Vented 274 48 24 22 72 5
Carnival (Suits twin piston caliper) 5/00 - 11/03 F 878 3 3 Vented 274 48 26 24 72 5
Carnival (Suits twin piston caliper) 12/03 - 05 F 2870 3 3 Vented 274 50.5 28 26 72 5
Grand Carnival 2006 - on F 2871 3 3 Vented 300 54.1 28 26 96.3 6
3.8Ltr V6 DOHC 24V

Cerato
2.0Ltr DOHC 2004 - on F 2872 3 Vented 275 47.5 26 24 69 4
R 2873 3 Solid 258 41.5 10 8 76 4

Credos
Credos 2.0 Litre 5/98 on F 873 3 Vented 258 48.5 24 22 72 4
R 874 3 Solid 260 40 10 8 72 4

Mentor
Mentor 1.5 Litre & 1.8 Litre 11/96 - on F 875 3 Vented 240 44 20 18 57 4
Shuma /Spectra 1997 - 2000
R 879 3 Solid 260 40 10 8 57 4

optima
Optima 2.5L V6 GL/GLS 6/2001 - on F 2894 3 Vented 257 47.5 25 22.4 69 4
R 2895 3 Solid 261 61.5 9.8 8.4 76 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 117
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
KIA - 4WD / SUV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

rio
Rio 1.5L 2002 - on F 2896 3 Vented 235 50 22 20 55 4
Rio 1.6L DOHC CVVT 2005 - on F 2893 3 Vented 256 47 22 20 62 4

sedona
3.8Ltr V6 DOHC 24V 2006 - on F 2871 3 3 Vented 300 54.1 28 26 96.3 6

SPECTRA
all - 4 & 5 door 2001 - 03 F 2898 3 3 Vented 302 54 28 26 96.2 5

Sorento
Sorento 4WD 3.5L V6 2003 - on F 2898 3 3 Vented 302 54 28 26 96.2 5
R 2899 3 Vented 315 87.5 20 18.4 96.2 5

sportage
Sportage/Sportswagon 4WD 11/96 - 03 F 876 Vented 284 51 24 22.4 96 5
All 4WD (USA) 2001 - 03
Sportage 2.7L V6 4WD 2004 - on F 468 Vented 280 47 26 22.4 69 5
2.0 CRDi 2WD 2005 F 468 Vented 280 47 26 22.4 69 5
R 458 Solid 262 61 10 8 76 4
2.0 16V 4WD, 2.7 V6 4WD 2005 F 468 Vented 280 47 26 22.4 69 5
2.0 CRDi 4WD R 465 Solid 284 61 10 8.4 76 5

pregio
Pregio 2.7L Diesel 2002 - on F 2897 3 Vented 258 57 26 24 87 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is
available under its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available
as a plain standard finish rotor

LADA
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

NIVA 2121, 4WD 1984 - 9/92 F 872 3 Solid 272 50.5 11 10 108 5
Samara, Cevaro 2108 1988 - 5/91 F 870 3 Solid 239 42.5 12 11 58.5 4
Volante, Sable 12/93 - on F 870 3 Solid 239 42.5 12 11 58.5 4

LAncia
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

Beta 1972 - 84 F 390 3 Solid 251 51 12.7 11.5 48.5 4
R 391 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 251 55 10 9 48.5 4

118 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
LAndrover / RANGE ROVER C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

110 & DEFENDER

110, 130 TD4 up to 1994 F 087 Solid 298 70 14 13 101.6 5
200, 300 TDi
90 1984 - on
110, 130 TD4 + TD5 1994 - on F 086 Vented 298 70 24 22 101.6 5
200, 300 TDi + LF Crew Cab
1994 - 98 R 088 Solid 290 61 12.7 11.7 101.6 5
110 series 1999 - on R 549 Solid 298 59 14 13 101.6 5
90, 110 series 2008 - on F 087 Solid 298 70 14 13 101.6 5
F 086 Vented 298 70 24 22 101.6 5
90 series 2008 - on R 088 Solid 290 61 12.7 11.7 101.6 5
110 series 2008 - on R 549 Solid 298 59 14 13 101.6 5

dISCOVERY I (LJ)
V8 Petrol 1989 - 98 F 087 Solid 298 70 14 13 101.6 5
2.5 TDi Diesel
(check if vented or solid) F 086 Vented 298 70 24 22 101.6 5
R 088 Solid 290 61 12.7 11.7 101 5

Please Note: Discovery I Series may have either Solid or Vented discs. Not interchangeable.
This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor
DISCOVERY II (LT)
V8 Petrol, TD5 Diesel 1999 - on F 528 Vented 297 91.5 25 22 70 5
S, SE & HSE R 093 Solid 304 62.7 12.6 11.7 70 5

DISCOVERY III (LM)

4.0L V6, 2.7L TDV6 2004 - on F 2090 Vented 317 62.2 30 27 79 5
R 2091 Vented 325 59.6 20 17 79 5
4.4L V8 Petrol 2004 - on F 2094 Vented 337.5 62.2 30 27 79 5
R 2095 Vented 350 59.6 20 17 79 5

freelander
1.8L Petrol + 2.0L Diesel up to 12/2000 F 526 Solid 262 51 14 11 66 5
V6 Petrol + TD4 Diesel 2001 - on F 527 Vented 277 51.5 21 18 66 5

RANGE ROVER CLASSIC

Classic 1972 - 1986 F 087 Solid 298 70 14 13 101 5
Classic (Vented Disc) 1990 - on F 086 Vented 298 70 24 22 101.6 5
Classic ( Rear ) 1972 - on R 088 Solid 290 61 12.7 11.7 101 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 119
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
LAndrover / RANGE ROVER C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

RANGE ROVER II
4.0 & 4.6L V8 P38 1995 - 01 F 092 Vented 297 64.6 25 22 70 5
Turbodiesel 2.5L 6cyl.
R 093 Solid 304 62.7 12.6 11.7 70 5

RANGE ROVER III

3.0L TD6 3/02 - 4/05 F 2092 Vented 344 76.2 30 28.4 79 5
4.4L V8 Petrol (210kw) 72mm pad face depth
R 2093 Solid 354 75 12 10.4 79 5
4.2L V8 Supercharged 2005 - on F 2098 Vented 360 81.3 30 27 79 5
R 2097 Vented 354 75.1 20 17 79 5
3.0L TD6 5/05 - on F 2099 Vented 344 76.2 30 27 79 5
4.4L V8 Petrol (225kw) 57mm pad face depth
R 2097 Vented 354 75.1 20 17 79 5

RANGE ROVER III SPORT

2.7L TDV6 2005 - on F 2090 Vented 317 62.2 30 27 79 5
R 2091 Vented 325 59.6 20 17 79 5
4.4L V8 Petrol 2005 - on F 2094 Vented 337.5 62.2 30 27 79 5
R 2095 Vented 350 59.6 20 17 79 5
4.2L V8 Supercharged 2005 - on F 2096 Vented 360 62.2 30 27 79 5
R 2095 Vented 350 59.6 20 17 79 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

120 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
lexus C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

RX 300
MCU10, ACU10 1998 - 11/01 F 2712 3 Vented 296 49.5 28 26 62 5
734 3 Solid 288 65 10
R 9 62 5

RX 330 + RX 350
3.3L V6 4WD + FWD 3/03 - 06 F 2702 3 3 3 Vented 320 49.3 28 26 62 5
3.5L 2006 - 09 R 2703 3 3 3 Solid 288 69.5 10 8.5 62 5

ES 300
ES 300 1992 - 99 F 735 3 3 Vented 275 49.5 28 26 62 5
R 734 3 Solid 288 65 10 9 62 5
ES 300 8/99 - 01 F 735 3 3 Vented 275 49.5 28 26 62 5
ES 300 7/01 - 06 F 2705 3 Vented 296 49.3 28 26 62 5
3.0L V6 (MCV30) R 2711 3 Solid 269 65 12 10.5 62 5

GS 450H
all models 2007 - on F 2720 3 Vented 334 51 30 27 62 5
R 2721 3 Vented 310 67.5 18 16.5 62 5

GS series
all models 1993 - 05 F 4748 3 Vented 296 51 32 30 62 5
R 749 3 3 Solid 307 63 12 10.5 62 5

GX series
All models 9/02 - 09 F 2700 3 3 3 Vented 338 68 28 26 108 6
R 793 3 3 Vented 312 68 18 16 106 6

IS 200
IS 200 99 - 2/05 F 4748 3 Vented 296 51 32 30 62 5
R 749 3 3 Solid 307 63 12 10.5 62 5

IS 250
All models 2006 - on F 2726 3 Vented 296 49.5 28 26 62 5
R 2727 3 Solid 291 61.5 10 8.5 62 5

IS 300
all models 2000 - 05 F 4748 3 Vented 296 51 32 30 62 5
R 749 3 3 Solid 307 63 12 10.5 62 5

IS 350
all models 2007 - on F 2720 3 Vented 334 51 30 27 62 5
R 2721 3 Vented 310 67.5 18 16.5 62 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 121
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
lexus C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ls 400
LS 400 4/90 - 92 F 737 3 Vented 276 51 28 26 60 5
R 738 3 Vented 291 67.5 16 15 60 5
LS 400 1993 - 94 F 4748 3 Vented 296 51 32 30 62 5
LS 400 1995 - 2000 F 745 3 Vented 315 53.5 28 26 62 5
R 746 3 Vented 307 67 16 15 62 5

LS 430
V8 4.2 litre 5/01 - 11/02 F 845 3 Vented 315 50.25 30 28 62 5
R 846 3 Vented 310
PART NOT AVAILABLE
REFERENCE ONLY
67.5 16 14.5 62 5

LS 460
All models 2007 - on F 2728 Vented 357.1
PART NOT AVAILABLE 60.5 34 31 62 5
R 2729 Vented 334.9
REFERENCE ONLY
66 22 20 62 5

LX 470
V8 DOHC 4.7L 4WD 4/1998 - 07 F 788 Vented 312 71 32 30 115 5
R 789 Vented 330 103 18 16 110 5

LX 570
5.7-liter V8 2008 F 2722 Vented 340 83.6 29 112 115 5
R 2723 Vented 345 76.5 18 16 112 5

SC series
SC 300 1999 - 00 F 4748 3 Vented 296 51 32 30 62 5
SC 400 1992 - 00 R 749 3 3 Solid 307 63 12 10.5 62 5
SC 430 2002 - 05

SOARER
JZZ30 Eng: 1JZGTE 2.5L TURBO 1991 - on F 4748 3 Vented 296 51 32 30 62 5
UZZ32 Eng: 1UZFE 4.0L V8
R 746 3 3 Vented 307 67 16 15 62 5
JZZ31 Eng: 2JZGE 3.0L 1994 - on F 568 3 Vented 275 49.5 28 26 62 5
UZZ30 Eng: 1UZFE 4.0L V8 1991 - on
UZZ31 Eng: 1UZFE 4.0L V8
R 586 3 Vented 291 67.5 16 15 60 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

LEYLAND
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

P76 1973 - 74 F 068 3 Vented 273 62 25.4 22.74 HUB 5

122 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
LOTUS C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ELISE S1
All except SPORT 3/2000 - on F&R 5355 3 Vented 280 26 26 24.5 56.6 4
Sport 135, 190, 111S 3/2000 - on F&R 52356 3 Vented 280 29.4 26 24.5 56.6 4
(models with Lotus OEM cross-drilled rotors)

ELISE S2 / EXIGE
Elise S2 2001 - on F&R 42355 3 3 Vented 288 44.5 26 24.5 60.1 4

LOTUS UPGRADE OPTION

Elise S2 2001 - on F&R 52358 3 Vented 296 44.5 26 24.5 60.1 4

MASERATI
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

Biturbo 2.0, 2.5 1982 - on F 439 3

PART NOT AVAILABLE

REFERENCE ONLY Solid 282 59 12.7 11.4 60 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 123
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MAZDA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

EARLY SERIES
1500 SUE 11/66 - 68 F 330 3 Solid 250 31 10 9 80 4
1500 SS, 1800 SUA 1967 - 68
PART NOT AVAILABLE
808, 1300 STC 1972 - 75 F 331 3
REFERENCE ONLY Solid 230 33 11 10 72 4
1300 FA3, STB 1970 - 75 F 332 3 Solid 244 50 10 9 72 4
PART NOT AVAILABLE
Capella SNA 1600 1973 - 74 F 338 3
REFERENCE ONLY Solid 230 34.5 12 11 72 4

121, 121L SERIES

121, 121L CD2, CD5 1976 - 80 F 335 3 Vented 250 37.5 18 17 80 4
121 DA (Shades) 86 - 11/90 F 635 3 Solid 219 37 13 11 75 4
121 DB 1.5 Litre 11/90 on F 530 3 Vented 235 45.5 18 16 55 4
121 DB 1.3 Litre 11/90 on F 525 3 Solid 235 45 12 10 55 4
121 DW Metro 8/96 on F 530 3 Vented 235 45.5 18 16 55 4

323 SERIES
FA4 RWD 11/76 - 8/80 F 339 Solid 206 54 13 12 Hub 4

FA4 P/Van, S/Wagon RWD 1978 - 85 F 337
PART NOT AVAILABLE Solid 229 54 13 12 Hub 4
REFERENCE ONLY

BD10 FWD 1981 - 85 F 100 3 Solid 228 31 11 10 75 4
BF 11/85 - 89 F 930 3 Vented 238 31 18 16 75 4
BF Wagon 6/86 - 88 Check Disc Diamater
BF10 All with rear disc 4/87 - 89 F 101 3 Vented 260 32 18 16 75 4
except wagon, Turbo only Check Disc Diamater
BF Wagon 6/86 - 88 R 933 3 NOT
PART AVAILABLE Solid 221 35 10 8 Hub 4
REFERENCE ONLY
Hub Seal Dia. 65mm
BF10 Turbo, 2WD 4/87 - 89 R 931 3 Solid 222 35 10 8 Hub 4
All except 4WD Hub Seal Dia. 54mm
PART NOT AVAILABLE
BF10 Turbo 4WD 4/87 - 89 R 932 3 Solid 247 30
REFERENCE ONLY 10 8 75 4
BG Astina 1.6L, 1.8L SOHC 1990 - 94 F 532 3 3 Vented 235 45.5 22 20 55 4
BG 1.8L SOHC 1990 - 94 R 531 3 3 Solid 231 35 9 8 55 4
BG Astina 1.8L DOHC 1990 - 94 F 533 3 3 Vented 257 45.5 22 20 55 4
BA Protege 1.6L, 1.8 DOHC 94 - 4/98
R 534 3 3 Solid 250.5 34.5 9 8 55 4
BA Astina 2.0L & V6 5/94 - 4/98 F 535 3 Vented 274 45 22 20 72 5
R 536 3 Solid 251 34.5 9 8 72 5
BJ Astina, Protege 1.6L 1998 - on F 532 3 3 Vented 235 45.5 22 20 55 4
BJ Astina Protege 1.8L, 1998 - on F 537 3 Vented 258 47 24 22 55 4
R 539 3 Solid 261 40 10 8 55 4
BJ Astina Protege 2.0L SP20 1998 - on F 577 3 Vented 258 48.5 24 22 72 5
R 951 3 Solid 261 40 9.5 8 72 5

124 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MAZDA - 626 C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

626 SERIES
CB2MS RWD 1978 - 82 F 333 Solid 231 50 13 12 Hub 4
GC FWD 2/83 - 2/84 F 119 3 Solid 250 35 14 12.5 75 4
GC FWD & Turbo 1984 - 87 F 334 3 Vented 250 35 20 18.5 75 4
R 945 3 Solid 254 50.2 10.2 9 Hub 4
GD FWD 1987 - 91 F 633 3 Vented 264 47 24 22 64 5
GD (2 wheel steer) 1987 - 91 R 634 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 258 64 10 8 Hub 5
GD (4 wheel steer) 5/89 - 91 R 948 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 260 40 10 8 Hub 5
GE, EE 2.0 Litre, V6 1992 - 3/97 F 950 3 Vented 258 49 24 22 72 5
GF 2.0 Litre 4/97 - on
incl. GF Series II R 951 3 Solid 261 40 9.5 8 72 5
GV 626 Wagon 2WD/4WD 1988- 9/97 F 633 3 Vented 264 47 24 22 64 5

929 / 929L SERIES

PART NOT AVAILABLE
LA2 RWD 1974 - 76 F 338 3
REFERENCE ONLY Solid 230 34.5 12 11 72 4
LA2 RWD 1976 - 79 F 335 3 Vented 250 37.5 18 17 80 4
929L LA4, LA5 RWD 1978 - 2/82 F 630 3 Vented 250 56 18 17 Hub 4
P.C.D. 120mm
HBES Coupe, Sedan (Hardtop) 1984 - 87 F 940 3 Vented 246 56 20 18 Hub 4
HBES 1984 - 87 R 942 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 255 45 10 9 66 4
HC10 V6 non-ABS Series I 1987 - 91 F 638 3 Vented 255 57 22 20 Hub 5
HC10 V6 1987 - 91 R 639 3 Solid 265 57 10 8 68 5
HC10 V6 Series II 11/89 - on F 659 3 Vented 255 72.4 22 20 Hub 5
HD10 5/91 - on F 955 3
PART NOT AVAILABLE
Vented 274
REFERENCE ONLY 47.5 24 22 72 5
R 956 Vented 286
PART NOT AVAILABLE
REFERENCE ONLY 56.5 18 16 72 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 125
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MAZDA - 3 / MPS / SPEED 3 C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MAZDA 2
1.5L Hatch 2003 - on F 2958 3 Vented 258 43.5 22 20 55 4

MAZDA 3 + MPS - AUSTRALIA

2.0L Sedan, Hatch 2003 - on F 2954 3 Vented 278 49 25 23 72 5
NEO, MAXX, MAXX sport R 2955 3 Solid 264 41 11 9 72 5
2.3L SP23 2003 - 08 F 2956 3 3 Vented 300 49 25 23 72 5
2.5L SP25 2009 - on R 2957 3 3 Solid 279.5 41.5 11 9 72 5
MPS 2.3L 4 Cyl Turbo 2006 - on F 2962 3 3 Vented 320 49 25 23 72 5
R 2957 3 3 Solid 279.5 41.5 11 9 72 5

MAZDA 6
2.3L DOHC MZR 2002 - on F 2950 3 Vented 274 47.5 22 24 72 5
Sedan, Hatch, Wagon R 2951 3 Solid 280 40 10 8 72 5
MPS 2.3L 4cyl TURBO 2005 - on F 2960 3 3 Vented 320 46.5 25 23 72 5
R 2961 3 3 Solid 314 41 11 9 72 5

MX-3
with rear drum 1992 - 95 F 533 3 3 Vented 257 45.5 22 20 55 4
with rear disc 1992 - 95 F 533 3 3 Vented 257 45.5 22 20 55 4
R 534 3 3 Solid 250 34.5 9 8 55 4

MX-5 - MIATA
na 1.6 & 1.8 10/89 - 9/93 F 530 3 Vented 235 45.5 18 16 55 4
R 531 3 Solid 231 35 9 8 55 4
nA & nb 1.8 9/93 - 2000 f 538 3 3 Vented 255 45 20 18 55 4
incl. Titanium & SP Turbo Auto. 2000 - on
Rear suits all models 1998 - on R 534 3 3 Solid 250 34.5 9 8 55 4
incl. Titanium & SP Turbo Auto.
NB 1.8L Titannium & SP Turbo 8/03 - 5/05 F 545 3 3 Vented 270 46 22 20 55 4
* Manual models only *

NB 1.8L Roadster 2005 model 2005

R 546 3 3 Solid 276 35 10 8 55 4
NC 2.0L 5/05 - on F 2959 3 3 Vented 290 45.1 22 20 72 5
R 2951 3 3 Solid 280 40 10 8 72 5

MAZDA 5 (Europe)
All models with 16” wheels 2005 - on F 2956 3 3 Vented 300 49 25 23 72 5

126 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MAZDA - 6 / mx-5 / rx-7 C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MX 6
GC & Turbo 1986 - 87 F 334 3 Vented 250 35 20 18.5 75 4
R 945 3 Solid 254 50.2 10.2 9 Hub 4
GD Turbo 1987 - 91 F 633 3 Vented 264 47 24 22 64 5
PART NOT AVAILABLE
GD 2WS 1987 - 91 R 634 3
REFERENCE ONLY Solid 258 50 10 8 Hub 5
GD 4WS 5/89 - 91 R 948 3 Solid 260 40 10 8 Hub 5
GE 11/91 on F 950 3 Vented 258 49 24 22 72 5
R 951 3 Solid 261 40 9.5 8 72 5

PREMACY
1.8L (rear drum brakes) 1999 - 01 F 950 3 Vented 258 49 24 22 72 5
2.0L 2001 - on R 951 3 Solid 261 40 9.5 8 72 5

RX-1 & 2
R100 1969 - 72 F 332 3 Solid 244 50 10 9 72 4
PART NOT AVAILABLE
RX2 S122A 1970 - 76 F 338 3
REFERENCE ONLY Solid 230 34.5 12 11 72 4

RX-3 & 5
PART NOT AVAILABLE
RX3 S102A 1972 - 76 F 331 3
REFERENCE ONLY Solid 230 33 11 10 72 4
PART NOT AVAILABLE
RX3, S124A RX4 1972 - 78 F 338 3 REFERENCE ONLY Solid 230 34.5 12 11 72 4
RX5 CD23 1976 - 79 F 335 3 Vented 250 37.5 18 17 80 4

RX-7
RX7 Series 1, 2 SA22 1979 - 83 F 336 Vented 228 59 18 17 Hub 4
PART NOT AVAILABLE
RX7 Series 2 SA22C 1981 - 83 R 935 3 Solid 235 50
REFERENCE ONLY 10 9 47.5 4
RX7 Series 3 SA22 1983 - 1/86 F 946 3 Vented 250 65 22 20 Hub 4
PART NOT AVAILABLE
RX7 Series 3 SA22 1983 - 1/86 R 936 3REFERENCE
Vented 257
ONLY 63 20 18 66 4
RX7 Series 4 FC1 2/86 - 4/92 F 636 3 Vented 276 65 22 20 77 5
RX7 Series 4 (Turbo) FC1 2/86 - 4/92 R 637 3 Vented 273 53 20 18 66 5
RX7 FD 103 4/92 - on F 947 3 3 Vented 294 67 22 20 72 5
PART NOT AVAILABLE
R 952 3REFERENCE
Vented 294
ONLY 45 20 18 72 5
RX7 SP Series 6 4/92 - on F 2558 3 Vented 314 67.5 32 30 72 5
R 2559 3 Vented 314 45.5 20 18 72 5

rx-8
RX8 - Standard Suspension Models 2003 - on F 42552 3 Vented 302.5 45 24 22 72 5
R 42551 3 Vented 302 43 18 16 72 5
RX8 - Sports Suspension Models 2003 - on F 42550 3 3 Vented 323 46 24 22 72 5
( AUSTRALIA ) R 42551 3 Vented 302 43 18 16 72 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 127
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MAZDA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

B SERIES
PART NOT AVAILABLE
B1800 - B2000 - B2200 1980 - 85 F 941 3
REFERENCE ONLY Solid 255 36 20 19 80 4
B2000 - B2200 - B2600 1985 - 96 F 631 3 Vented 256 20 20 18 86 6
2WD
B2000 - B2200 - B2600 1985 - 96 F 965 3 Vented 272 25 22 20 93 6
4WD
B2500 - B2600 2WD 1996 - 02 F 958 3 Vented 255.5 24 24 22 86 6
B2500 - B2600 4WD 1996 - 02 F 959 3 Vented 274 28 28 26 93 6
B2500 - B2600 4WD 2002 - on F 2952 3 3 Vented 288.5 70.5 28 26 98 6
B2600 4WD 1998 - 02 F 964 3 Vented 275 24 24 22 93 6
BT50 2WD 8/06 - on F 958 3 Vented 255.5 24 24 22 86 6
BT50 4WD 5/06 - on F 2952 3 3 Vented 288.5 70.5 28 26 98 6

CX-7
All Models 2007 - on F 2562 Vented 296 48.5 28 26 72 5
R 2563 Vented 302 57 18 16 72 5

E SERIES
E1400 - E1800 Van 1984 - 97 FR 632A RH Vented 231.5 58.5 18 16 Hub 4
Wagon & Short Body FL 632B LH Vented 231.5 58.5 18 16 Hub 4
Traveller / Esky ID Groove
E2000 - E2200 Van 1984 - 5/92 F 631 3 Vented 256 20 20 18 86 6
STD & LWB
E2000 - 2200 Pickup 1984 - 97 F 934 3 Vented 268 20 20 18 86 6
E2000 - 2200 Van 5/92 - 99 F 958 3 Vented 255.5 24 24 22 86 6

MPV
LV10E1 1993 - on F 960 3 Vented 276 64 28 26 72 5
LV10E2 12/95 - on F 961 3
PART NOT AVAILABLE
Vented 276
REFERENCE ONLY 58 28 26 72 5
R 956 3REFERENCE
PART NOT AVAILABLE
Vented 286
ONLY 57 18 16 72 5
LVW (D) 2.5L V6, 3.0L 9/1999 - on F 962 3 Vented 274 51 28 26 72 5
4 Door Wagon R 956 3
PART NOT AVAILABLE
Vented 286
REFERENCE ONLY 57 18 16 72 5

TRIBUTE
all models 2000 - 05 F 957 3 3 Vented 278 47 24 22 72 5
2.3L 4 cyl, 3.0L V6 2006 - on F 2560 3 3 Vented 302.7 47.2 26 24 72 5
R 2561 3 Solid 302 56.1 12 11 72 5

XEDOS 6
1.6L / 1.8L / 2.0L. 1992 - 00 F 950 3 Vented 258 49 24 22 72 5

128 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

C140 - COUPE
500 SEC, S500 Coupe 1993 - 95 F 284 3 Vented 320 82 30 27.4 67 5
R 285 3
PART NOT AVAILABLE
Vented
REFERENCE ONLY 300 60 22 19.4 67 5

R107 - SPORTS
350 SL > 009599 1972 - 73 F 257 3 Vented 273 67 22 20 80 5
350 SLC > 005715
280, 350, 450 SL, SLC 1973 - 80 F 255 3
PART NOT AVAILABLE
Vented 278
REFERENCE ONLY 67 22 20 80 5
380, 500 SL, SLC 1980 - 85 F 258 3REFERENCE
PART NOT AVAILABLE
Vented 278
ONLY 69 22 19.4 80 5
560 SL 1986 - 89 F 264 3 Vented 284 43 22 19.4 67 5
All R107 1972 - 89 R 251 3 Solid 279 72 10 8.3 67 5

R129 - SPORTS
R129, 500 SL 1985 - 90 F 264 3 Vented 284 43 22 19.4 67 5
500 SL, SL500 1990 - 94 F 280 3
PART NOT AVAILABLE
Vented
REFERENCE ONLY 300 45.5 28 25.4 67 5
R 281 3 Solid 278 58.5 9.1 7.3 67 5

W108 / W109
250, 280 S, SE 1965 - 68 F 250 3 Solid 273 63.3 12.7 10.6 70 5
250, 280 S, SE, SEL, 3.5 1968 - 72 F 256 3 Vented 273 67.4 19.1 18
PART NOT AVAILABLE
69 5
REFERENCE ONLY
300 SEL 3.5, 6.3 1968 - 72
R 251 3 Solid 279 72 10 8.3 67 5

W110 / W111
190C, 190D, 200, 230 Up to 1965 F 253 3 Solid 253 67.3 12.7 11.1 69.5 5
220B, S, SB, SEB, 230S Up to 1965
R 251 3 Solid 279 72 10 8.3 67 5

W111 / W112 - COUPE

250, 280 SE/C 1965 - 68 F 250 3 Solid 273 63.3 12.7 10.6 70 5
280 SE/, 280 SE/C 3.5 1968 - 72 F 256 3 Vented 273 67.4 19.1 18
PART NOT AVAILABLE
69 5
REFERENCE ONLY
250, 280 SE/C 3.5 1965 - 72
R 251 3 Solid 279 72 10 8.3 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 129
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W113 - SPORTS
230 SL 1965 - 68 F 253 3 Solid 253 67.3 12.7 11.1 69.5 5
250, 280 SL 1968 - 72 F 250 3 Solid 273 63.3 12.7 10.6 70 5
230, 250, 280 SL 1965 - 72 R 251 3 Solid 279 72 10 8.3 67 5

W114 / W115
200, 220, 230 1968 - 71 F 250 3 Solid 273 63.3 12.7 10.6 70 5
230/6, 250, 250 C, CE
250, 230/6 250 C, CE 1971 - 74 F 252 3 Solid 273 63.3 12.7 10.6 80 5
240 D, 230
230/6, 250 C, CE 1973 - 76 F 254 3 Solid 278 63.3 12.7 10.6 80 5
280 E, C, CE
All W114, W115 1968 - 76 R 251 3 Solid 279 72 10 8.3 67 5

W116
280 S, SE, SEL 1972 - 80 F 255 3 Vented 278
PART NOT AVAILABLE 67 22 20 80 5
REFERENCE ONLY
350, 450 SE, SEL
All W116 1972 - 80 R 251 3 Solid 279 72 10 8.3 67 5

W123
230, 240 D, 250 1976 - 78 F 254 3 Solid 278 63.3 12.7 10.6 80 5
280 E, CE, TE 1976 - 84
230 E, 300 D, 300 TD 1976 - 84
All W123 1976 - 84 R 251 3 Solid 279 72 10 8.3 67 5

W126
PART NOT AVAILABLE
280, 380, 500 SE, SEL 1981 - 86 F 258 3 Vented 278
REFERENCE ONLY 69 22 19.4 80 5
300, 420, 560 SE, SEL 1986 - 91 F 262 3 Vented 300 68.5 27.5 25.4 80 5
380, 500 SEC 1981 - 86 F 259 3 Vented 286 60 22 19.4 80 5
560 SEC 1986 - 91 F 262 3 Vented 300 68.5 27.5 25.4 80 5
All W126 Rears 1981 - 91 R 251 3 Solid 279 72 10 8.3 67 5

130 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W124
230 E, TE, 300 D 1986 - 89 F 263 3 Solid 284 46 12 10 67 5
260, 300 E, TE 1986 - 91 F 264 3 Vented 284 43 22 19.4 67 5
230 TE 1986 - 91
300 CE 1986 - 89
230, 260, 300 E, 300 D 1986 - 91 R 261 3 Solid 258 55 9 7.3 67 5
300 CE 1986 - 89
220 E, E220, 230 E 1991 - 95 F 264 3 Vented 284 43 22 19.4 67 5
280 E, E280, 300 E
300 E 24V 1990 - 92 F 266 3 Vented 295 49.5
PART NOT AVAILABLE
22 19.4 67 5
REFERENCE ONLY
320 E, E320 1993 - 94 F 266 3 Vented 295 49.5 22 19.4 67 5
320 E, E320 1994 - 95 F 268 3 Vented 294 50 24 22.4 67 5
220 E, E220, 230 E 1990 - 95 R 261 3 Solid 258 55 9 7.3 67 5
260 E, 280 E, E280
300 E, 300 D, E300 D
300 E 24V, 320 E, E320 1990 - 95 R 267 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 56 9 7.3 67 5
300 D 1990 - 93 F 263 3 Solid 284 46 12 10 67 5
E300 D 1990 - 94 F 263 3 Solid 284 46 12 10 67 5
E220 Coupe, Convertible 1995 on F 269 3 Vented 284 43 22 19.4 67 5
E220 Convertible 1990 - 95 R 267 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 56 9 7.3 67 5
E220 Coupe 1995 on R 261 3 Solid 258 55 9 7.3 67 5
300 CE 24V Coupe 1990 -92 F 266 3
PART NOT AVAILABLE
Vented 295
REFERENCE ONLY 49.5 22 19.4 67 5
R 267 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 278 56 9 7.3 67 5
E320, 320 CE 1993 - 94 F 266 3 Vented 295 49.5 22 19.4 67 5
(Up to Chassis No. B162121)
E320, 320 CE 1993 - 94 F 268 3 Vented 294 50 24 22.4 67 5
(Chassis No. B162121 on)
E320, 320 CE 1993 - 94 R 267 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 56 9 7.3 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 131
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W140
300 SE 3.2 1992 - 93 F 282 3 Vented 310 82 28 25.4 67 5
(Up to Chassis No. A050548)
300 SE 3.2 1993 - 95 F 284 3 Vented 320 82 30 27.4 67 5
(Chassis No. A050548 on)
S280, 300 SE 3.2, S320 1992 - 95 R 283 3 Solid 290 60 12 9.8 67 5
S280, S320, 400 SE, S420 1992 - 98 F 284 3 Vented 320 82 30 27.4 67 5
400, 500 SEL, S500 1992 - 98
S600, 600 SEL V12 1992 - 98
400 SE, S420, 420 SEL, 1992 - 95 R 285 3 Vented 300 60 22 19.4 67 5
PART NOT AVAILABLE
500 SEL, S500, REFERENCE ONLY

S600, 600 SEL V12

W201
190 E, 190 D 2.5 1985 - 88 F 260 3 Solid 262 43 11 9 67 5
190 E, 190 E 1.8 1988 - 91
190 E 2.3 16 Valve 1985 - 88 F 264 3 Vented 284 43 22 19.4 67 5
190 E 2.3, 2.6 1986 - 93 F 279 3 Vented 262 44.5 22 19.4 67 5
190 E 1.8, 190 D 2.5, 190 E 1985 - 91 R 261 3 Solid 258 55 9 7.3 67 5

W168
A140 07/97 - 08/04 F 556 3 Solid 260 40.5 12 10 67 5
A140 07/97 - 08/04 F 557 3 Vented 260 40.5 22 19 67 5
A160 07/97 - 08/04 F 557 3 Vented 260 40.5 22 19 67 5
R 559 3 Solid 258 55.2 8 7 67 5
A190 03/99 - 08/04 F 558 3 Vented 276 35.5 22 19 67 5
R 559 3 Solid 258 55.2 8 7 67 5
A160 CDI 07/98 - 08/04 F 556 3 Solid 260 40.5 12 10 67 5
A170 CDI 07/98 - 02/01 F 557 3 Vented 260 40.5 22 19 67 5
A170 CDI 02/01 - 08/04 F 557 3 Vented 260 40.5 22 19 67 5

132 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ - 4WD / SUV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W202
C180 03/93 - 05/00 F 265 3 Solid 284 43.5 12 10 67 5
C200 01/94 - 05/00 F 264 3 Vented 284 43 22 19.4 67 5
C200 KOMPRESSOR 10/95 - 05/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C220 03/93 - 05/00 F 264 3 Vented 284 43 22 19.4 67 5
C230 03/93 - 05/00 F 264 3 Vented 284 43 22 19.4 67 5
C230 KOMPRESSOR 10/95 - 05/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C240 10/95 - 05/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C280 05/93 - 05/00 F 264 3 Vented 284 43 22 19.4 67 5
C280 05/93 - 05/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 CDI 09/97 - 05/00 F 264 3 Vented 284 43 22 19.4 67 5
C200 D 03/93 - 05/00 F 265 3 Solid 284 43.5 12 10 67 5
C220 CDI 09/97 - 05/00 F 264 3 Vented 284 43 22 19.4 67 5
C220 D 03/93 - 05/00 F 265 3 Solid 284 43.5 12 10 67 5
C250 D 05/93 - 05/00 F 265 3 Solid 284 43.5 12 10 67 5
C250 TD 10/95 - 05/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C36 AMG 9/95 - 8/97 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 290 54 10 8.3 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 133
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

S202
C180 T 06/96 - 09/00 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 T 06/96 - 03/01 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200T KOMPRESSOR 06/96 - 03/01 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230 T 06/96 - 06/98 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230T KOMPRESSOR 06/97 - 09/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C240 T 06/96 - 09/00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C240 T 09/00 - 03/01 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C280 T 06/97 - 03/01 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 T CDI 06/96 - 03/01 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 T D 06/96 - 03/01 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C220 T CDI 06/96 - 03/01 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C220 T D 06/96 - 03/01 F 264 3 Vented 284 43 22 19.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C250 T TURBO-D 06/96 - 03/01 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5

134 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ - 4WD / SUV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W203
C180 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C22 CGI KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 KOMPRESSOR 05/00 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C180 05/00 - 05/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230 01/05 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C240 05/00 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C240 4-MATIC 07/02 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C280 inc. 4-Matic 01/05 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C320 05/00 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C320 4-MATIC 07/02 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C200 CDI 05/00 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C220 CDI 05/00 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C270 CDI 12/00 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
All Models inc. AMG 2001 - 07 F 2272 Vented 330 47 28 26 67 5
w/ OEM Sports Package

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 135
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W204
C180 CGI 1/07 - on F 2264 Vented 288 64.5 25 22.4 67 5
F 2262 Vented 295 64.5 28 25.4 67 5
R 2261 Solid 278 55.5 9 7.3 67 5
**Check Dimensions** R 2263 Solid 300 55.5 10 8.3 67 5
C180 Kompressor 1/07 - on F 2264 Vented 288 64.5 25 22.4 67 5
F 2262 Vented 295 64.5 28 25.4 67 5
R 2261 Solid 278 55.5 9 7.3 67 5
**Check Dimensions** R 2263 Solid 300 55.5 10 8.3 67 5
C200 CDI 1/07 - on F 2264 Vented 288 64.5 25 22.4 67 5
F 2262 Vented 295 64.5 28 25.4 67 5
R 2261 Solid 278 55.5 9 7.3 67 5
**Check Dimensions** R 2263 Solid 300 55.5 10 8.3 67 5
C200 CGI, C220 CDI 1/07 - on F 2262 Vented 295 64.5 28 25.4 67 5
C200 Kompressor, C230 1/07 - on R 2263 Solid 300 55.5 10 8.3 67 5
C230 4-Matic 7/07 - on
**Check Dimensions**
C250 CDI, C250 CGI 8/08 - on F 2262 Vented 295 64.5 28 25.4 67 5
C280 inc. 4-Matic 1/07 - on F 2262 Vented 295 64.5 28 25.4 67 5
(exc. AMG sports package) R 2263 Solid 300 55.5 10 8.3 67 5
**Check Dimensions**

S203
C180 03/01 - 05/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C180 03/01 - 05/02 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C180 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C180 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 CGI KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C200 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C200 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

136 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ - 4WD / SUV C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

S203 - continued
C230 01/05 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C240 inc. 4-Matic 03/01 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C280 inc. 4-Matic 01/05 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C320 inc 4-Matic 03/01 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C200 CDI 03/01 - 07 F 286 3 Vented 288 47 25 22.4 67 5
C220 CDI 03/01 - 07 F 286 3
PART NOT AVAILABLE
Vented 288
REFERENCE ONLY 47 25 22.4 67 5
C270 CDI 03/01 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

S204
C180, C200, C220, C230 1/07 - on F 2264 3 Vented 288 64.5 25 22.4 67 5
C250, C280, C280 4-Matic 1/07 - on F 2262 3 Vented 295 64.5 28 25.4 67 5
C320 1/07 - on R 2261 Solid 278 55.5 9 7.3 67 5
**Check Dimensions** R 2263 Solid 300 55.5 10 8.3 67 5

CL203
C160 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C180 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 CGI KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230 KOMPRESSOR 05/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C180 03/01 - 05/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C200 KOMPRESSOR 03/01 - 05/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C230 01/05 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C230 KOMPRESSOR 03/01 - 05/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 137
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CL203 - Continued
C320 09/02 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
C200 CDI 03/01 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
C220 CDI 03/01 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5

C203
CLK200 06/97 - 06/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
CLK200 KOMPRESSOR 06/97 - 06/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
CLK230 KOMPRESSOR 06/97 - 06/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
CLK320 06/97 - 06/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

A208
CLK200 03/98 - 03/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
CLK200 KOMPRESSOR 03/98 - 03/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK230 KOMPRESSOR 03/98 - 03/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK320 03/98 - 03/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

C208 / 209
CLK200 CGI 09/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
CLK200 KOMPRESSOR 09/02 - 07 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
CLK240 06/02 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK320 06/02 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK270 CDI 10/02 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

138 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

A209
CLK200 CGI 02/03 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK200 KOMPRESSOR 02/03 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK240 02/03 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
CLK320 02/03 - 07 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

W210
E200 3 Vented 288
6/95 - 3/02 F 286 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E200 D 6/95 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E200 CDI 1998 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E200 KOMPRESSOR 2000 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
(120Kw) R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E200 KOMPRESSOR 1997 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
(137Kw) R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E220 D 6/95 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E220 CDI 1998 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E230 6/95 - 97 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E240 V6 1997 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E240 V6 w/ ESP 1997 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E250 D 6/95 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E250 TD 6/95 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E270 CDI 1999 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E280 1996 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 139
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

W210 - Continued
E280 4-MATIC 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E290 TD 1996 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E300 D 6/95 - 3/02 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E300 TD 1996 - 99 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E320 6/95 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E320 CDI 1999 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5
E320 4-Matic 1997 - 3/02 F 288 3 Vented 300 47 28 25.4 67 5
R 289 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 290 54 10 8.3 67 5

s210
E200 5/96 - 00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
E200 KOMPRESSOR (120Kw) 2000 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E200 KOMPRESSOR (137Kw) 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E220 CDI (Short Wheelbase) 1998 - 3/03 F 286 3 Vented 288 47 25 22.4 67 5
E220 CDI (Long Wheelbase) 1998 - 3/03 F 286 3 Vented 288 47 25 22.4 67 5
E240 V6 1997 - 3/03 F 286 3 Vented 288 47 25 22.4 67 5
E240 V6 w/ ESP 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E250 D (Short Wheelbase) 5/96 - 99 F 286 3 Vented 288 47 25 22.4 67 5
E250 D (Long Wheelbase) 5/96 - 99 F 286 3 Vented 288 47 25 22.4 67 5
E270 CDI 1999 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E280 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E280 4-MATIC 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E290 TD (Short Wheelbase) 1996 - 99 F 286 3 Vented 288 47 25 22.4 67 5
E290 TD (Long Wheelbase) 1996 - 99 F 286 3 Vented 288 47 25 22.4 67 5
E300 TD 1996 - 99 F 288 3 Vented 300 47 28 25.4 67 5
E320 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E320 CDI 1999 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5
E320 4-Matic 1997 - 3/03 F 288 3 Vented 300 47 28 25.4 67 5

140 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

r170
SLK 200 1996 - 00 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
SLK 200 KOMPRESSOR 1996 - 2/04 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
SLK 230 KOMPRESSOR 1996 - 2/04 F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
SLK 320 2000 - 2/04 F 288 3 Vented 300 47 28 25.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5

r171
SLK 200 KOMPRESSOR 3/04 - on F 286 3 Vented 288 47 25 22.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5
SLK 280 2005 - on F 288 3 Vented 300 47 28 25.4 67 5
R 287 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 55 9 7.3 67 5

g - class - 4wd
G500 4Dr 5.0L V8 SOHC 2002 - 03 F 2250 3 3 Vented 315 83 30 27.4 85 5

M - CLASS (W163 & W164)

ML 230 1998 - 00 F 550 3 Vented 303 51 26 23 67 5
ML 270 Turbo Diesel 1999 - 01 R 551 3 Solid 285 53 15 13 67 5
(ch.>A289558)
ML 320 V6 (ch.>A289558) 1998 - 01
ML 270 Turbo Diesel 2002 - 03/05 F 552 3 3 Vented 345 51 32 30 67 5
(ch.A289559>) R 553 3 3 Solid 331 55.5 14 12 67 5
ML 320 V6 (ch.A289559>) 2002 - 03/05
ML 400 Turbo Diesel 2001 - 03/05 F 552 3 3 Vented 345 51 32 30 67 5
ML 430 V8 1998 - 01
ML 500 4WD Luxury V8 2001 - 03/05 R 553 3 3 Solid 331 55.5 14 12 67 5
ML 55 AMG 4WD V8 1999 - 03/05
ML 280, 320, 350 (W164) 4/05 - on F 2252 3 Vented 330 55 32 29.4 67 5
R 2253 3 Solid 330 63 14 11.4 67 5
ML 420, 500 (W164) 4/05 - on F 2254 3 Vented 350 55 32 29.4 67 5
ML 63 AMG (W164) 1/06 - on R 2255 3 Vented 330 63 22 19.4 67 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 141
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MERCEDES BENZ C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MB100 / MB140
MB100, MB100D - Van 11/99 - 03 F 2266 3 Vented 294 68.5 24 22 85 5
MB100D 2.9 Van 12/01 - 03
MB140, MB140D - Van 11/99 - 03

R - CLASS
R 280, R 320, R 350 1/06 - on F 2252 3 Vented 330 55 32 29.4 67 5
R 500, R 63 AMG 1/06 - on F 2254 3 Vented 350 55 32 29.4 67 5
Solid Rear 14mm Thick 1/06 - on R 2253 3 Solid 330 63 14 11.4 67 5
Vented Rear 22mm Thick 1/06 - on R 2255 3 Vented 330 63 22 19.4 67 5

Sprinter
All models 1995 - 5/06 F 566 3 Vented 276 77 22 19.5 85 5
Rear 12mm Thick R 2267 3 Solid 258 96.5 12 10 85 5
Rear 16mm Thick R 567 3 Solid 272 97 16 14 85 5
Rear 22mm Thick R 2268 3 Vented 285 93 22 19 120 6
3T, 3.5T 6/06 - on F 2270 3 Vented 299.5 68.5 28 25 85 6
R 2269 3 Solid 298 71.5 16 14 85 6
5T 6/06 - on F 2270 3 Vented 299.5 68.5 28 25 85 6

VITO
108D, 110D, 113D 1999 - 9/03 F 564 3 Vented 276 60 22 19.5 67 5
112 R 565 3 Solid 280 63 10 8.5 67 5

142 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MG C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MG Midget Mk I-II 1963 - 67 F 060 3 Solid 209.8 39.5 7.5 7 63.5 4

MG Midget Mk III 1967 - 72 (Wire Wheels)
MG Midget Mk I-II 1963 - 67 F 061 3 Solid 209.8 60 7.7 7 63 4
MG Midget Mk III 1967 - 72 (Disc Wheels)
MG B, GT 1962 - 66 F 062 3 Solid 273.4 44.5 8.7 7.6 73 4
MG B Mk II, GT Mk II 1967 - 72
MGF 1995 - 02 F 063 3 Vented 240 44 22 20 66 4
R 064 3 Solid 240 44 10 8.5 66 4

MINI - cooper
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

Mini Moke California 1971 - 73 F 079 3

PART NOT AVAILABLE
Solid 213 61 10 8.5 55 4
REFERENCE ONLY
DB815 Pads
Mini Cooper S 1964 - 67 F 081
PART NOT AVAILABLE
Solid 190 77.5 9.5 8.5 73.5 4
REFERENCE ONLY
Mini Clubman, GT 1970 - 73

MINI COOPER - R50

COUPE W10 Eng. 9/00 - on F 542 3 3 Vented 276 44 22 19 64 4
COUPE ONE 1.4d W17 Eng. 6/02 - on
COUPE ONE 1.4i W10 Eng. 2/02 - on

COUPE ONE 1.6i W10 Eng. 9/00 - on

R 543 3 3 Solid 259 44 10 8.4 64 4

MINI COOPER - R52 CONVERTIBLE

COOPER S W11 Eng. 11/02 - on F 542 3 3 Vented 276 44 22 19 64 4
COOPER W10 Eng. 11/02 - on
CONVERTIBLE ONE 1.4i 2/02 - on
R 543 3 3 Solid 259 44 10 8.4 64 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 143
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MINI - cooper C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MINI COOPER - R53

COUPE COOPER S W11 Eng. 9/00 - on F 542 3 3 Vented 276 44 22 19 64 4
R 543 3 3 Solid 259 44 10 8.4 64 4

MINI COOPER - R56

COUPE & CLUBMAN 10/05 - on F 2526 3 3 Vented 280 44 22 20.4 64 4
N12 Eng. exc. JCW upgrade R 543 3 3 Solid 259 44 10 8.4 64 4
COOPER S inc. CLUBMAN 10/05 - on F 2524 3 3 Vented 294 44 22 20.4 64 4
N14 Eng. exc. JCW upgrade R 543 3 3 Solid 259 44 10 8.4 64 4
JOHN COOPER WORKS 2007 - on F 2528 3 3 Vented 316 45 22 20.4 64 4
Coupe & Clubman R 2529 3 3 Solid 280 44 10 8.4 64 4

MINI COOPER - 2 PIECE UPGRADE

COOPER, COOPER S 2003 F 52525 3 Vented 320 48.5 28 27 64 4
Replacement for Brembo
Gran Turismo Big Brake System
5000 series 2-piece assembled

144 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

3000 GT
JF 10/92 - 5/94 F 213 3 3 Vented 296 45.2 30 28.4 69 5
R 214 3 3 Vented 284 52.8 20 18.4 90 5
3000 GT 5/94 - on F 216 3 3 Vented 314 45.5 30 28.4 69 5
R 217 3 3 Vented 297 50.5 20 18.4 90 5

3000 GT. GT-SL, GT-VR4 (USA)

GT & GT-SL 4/90 - 95 F 425 3 3 Vented 276 45 24 22.4 69 5
R 423 3 Vented 266 65.5 18 16.4 90 5
GT-VR4 1990 - 5/93 F 213 3 3 Vented 296 45.2 30 28.4 69 5
R 214 3 3 Vented 284 52.8 20 18.4 90 5
GT-VR4 6/93 - 99 F 216 3 3 Vented 314 45.5 30 28.4 69 5
R 217 3 3 Vented 297 50.5 20 18.4 90 5

380
ES, SX, VRX, LX, GT 2005 - on F 2206 3 3 Vented 294 46 28 26.4 69 5
R 2207 3 3 Vented 302 59.2 18 16.4 69 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 145
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

COLT
RA, RB, RC, RD, RE 1980 - 6/90 F 215 3 Solid 228 40 13 11.4 86 4

CORDIA
AA, AB Non Turbo 4/83 - 11/85 F 227 3 Solid 243 34.5 13 11.4 86 4
AC Non Turbo 12/85 - 7/89 F 219 3 Vented 242 34.5 18 16.4 86 4
AA, AB Turbo 5/84 - 11/85
AC Turbo 12/85 - 7/89 F 409 3 Vented 266 34 24 22.4 86 4

FTO / ECLIPSE 1.8Litre: 2.0Litre

1.8GS + 2.0L 14 inch wheels 9/94 - 9/97 F 411B 3 Vented 256 45 24 22.4 69 5
2.0L Mivec V6 15 inch wheels 9/94 - 9/97 F 425 3 3 Vented 276 45 24 22.4 69 5
1.8GS + 2.0L 14 inch wheels 10/97 - 8/00 F 421 3 Vented 256 45.2 24 22.4 69 5
All models 9/94 - 8/00 R 547 3 PART NOT AVAILABLE
REFERENCE ONLY Solid 260 41 10 8.4 90 5
Eclipse Turbo 2WD 1/1994 - 98 R 2203 3 Solid 262 60 10 8.4 90 5

GALANT
PART NOT AVAILABLE
GA, GB DB1026 Pads 1971 - 74 F 209 3
REFERENCE ONLY Solid 239 46 10 8.4 67 4
GC, GD 1974 - 77 F 210 3 Solid 229 30 13 11.4 67 4
HG 5/89 - 8/90 F 221 3 Vented 265 45.5 24 22.4 69 4
HH - Except VR4 Turbo 9/90 - 93 F 411 3 Vented 256 45 24 22.4 69 4
HH5 VR4 Turbo 9/90 - 93 F 402 3 3 Vented 276 45 24 22.4 69 4
HG, HH 5/89 - 93 R 403 3 Solid 265 49 10 8.4 90 4
HJ 1994 - on F 411 3 Vented 256 45 24 22.4 69 4
R 404 3 Solid 262 60 10 8.4 90 4

146 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

LANCER
LA, LB, LC 1974 - 81 F 210 3 Solid 229 30 13 11.4 67 4
CA 1988 - 8/90 F 219 3 Vented 242 34.5 18 16.4 86 4
CB 1, 2, 3, 4 1.5 Litre 9/90 - 93 F 412 3 Vented 236 34 18 16.4 86 4
CC GSR Turbo Sedan 10/92 - on F 411 3 Vented 256 45 24 22.4 69 4
R 406 3 Solid 260 41 10 8.4 90 4
CB 1.5 & 1.6L GSR 90 - 10/92 F 407 3
PART NOT AVAILABLE
Vented
REFERENCE ONLY 256 34 24 22.4 86 4
R 403 3 Solid 265 49 10.1 8.4 90 4
CC (Hatch 1.5 Litre) 10/92 - 02 F 412 3 Vented 236 34 18 16.4 86 4
CE 1.5 & 1.8 Litre 10/92 - 02 F 413 3 Vented 235 45 18 16.4 64 4
CC 1.8L Coupe
CC Sedan/Wagon
CC 1.5 Litre 10/92 - 02 F 408 3 Solid 235 45 13 11.4 64 4
CG 2.0L 14-inch wheels 2/2002 - 03 F 2200 3 Vented 256 45 24 22.4 64 4
CH 2.0L 14-inch wheels 7/2003 - 05
CH VR-X 2.0L 15-inch wheels 7/2003 - 05 F 2201 3 Vented 276 45.5 26 24.4 69 5
CH 2.4L all models 2006 - 08 R 2203 3 Solid 262 60 10 8.4 90 5
CJ Saloon + Sportback 03/2008 - on F 2201 3 Vented 276 45.5 26 24.4 69 5
(non-turbo) excl. VRX/Ralliart R 2209 3 Solid 262 60 10 8.4 80 5
CJ Ralliart 2008 - 3/09 F 417 3 3 3 Vented 294 46 24 22.4 69 5

EVOLUTION (LANCER)
EVO I, II, III 1993 - 95 F 402 3 3 Vented 276 45 24 22.4 69 4
* Check Dimensions * R 406 3 Solid 260 41 10 8.4 90 4
EVO IV, V, VI - RS models 1996 - on F 4428 3 Vented 276 45.5 24 22.4 69 5
Eng:4G63 15 inch wheels

suits 2-pot calipers 429 3

R 3 Vented 284 60.2 20 18.4 90 5
EVO IV GSR 1996 F 417 3 3 3 Vented 294 46 24 22.4 69 5
Eng:4G63 16 inch wheels
R 419
3 3 Vented 300 58 22 20 90 5
EVO V, VI, VII, VIII, IX GSR & RS-2 1996 - 08 F 4418 3 Vented 320 43.5 32 29.8 69 5
Eng:4G63 17 inch wheels F 52218 3 Vented 320 43.5 32 29.8 69 5
suits 4-pot Brembo calipers F 5418
This part number now supersedes to 52218
replacement rotors for owners of 5418 are still
available and the part number is 5418.1
R 419 3 3 Vented 300 57 22 20 90 5
EVO X incl MR models 2008 - 2010 F 42224 3 3 Vented 350 44 32 30 69 5

R 42225 3 Vented 330 59 22 20 80 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 147
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MAGNA
TM, TN, TP 1985 - 91 F 221 3 Vented 266 45.5 24 22.4 69 4
R 222 3 Solid 251 49 10 8.4 Hub 4

TN, TP Wagon Only 7/87 - 92 R 223 3 Solid 276 84 10 8.4 Hub 4

TR, TS - 4 Cyl models only 4/91 - on F 421 3 Vented 256 45.2 24 22.4 69 5
Except TR 4cyl with an ‘X’ in the
chassis no. - Manf. up to 8/92
TR 4 cyl up to 8/92 F 425 3 3 Vented 276 45 24 22.4 69 5
with an ‘X’ in the chassis no.
TR, TSV6 Non ABS models 1993 - on F 425 3 3 Vented 276 45 24 22.4 69 5
TR, TS V6 ABS models only 1993 - on F 425 3 3 Vented 276 45 24 22.4 69 5
TR, TS 4 Cyl + V6 Non ABS 4/91 - on R 422 3 Solid 258 66 10.4 8.4 90 5
TS V6 Sedan ABS 3/94 - on R 423 3 Vented 266 65.5 18 16.4 90 5
TS V6 Wagon ABS 3/94 - on R 427 3 Vented 284 65.5 20
PART NOT AVAILABLE
REFERENCE ONLY
18.4 90 5
TE 4 Cyl, V6 4/96 - on F 425 3 3 Vented 276 45 24 22.4 69 5
ABS & non ABS R 426 3 Solid 258 56.5 10.5 8.4 90 5
TF, TH, TJ, VR-X, Sports V6 6/97 - on F 425 3 3 Vented 276 45 24 22.4 69 5
TL (ES, LS, VR, VR-X) V6 R 426 3 Solid 258 56.5 10.5 8.4 90 5
TJ (II) AWD V6 1/2003 - on F 417 3 3 Vented 294 46 24 22.4 69 5
TL AWD V6 8/2003 - on R 429 3 3 Vented 284 60.2 20 18.4 90 5
TJ Ralliart 2002 - 03 R 42429 3 Vented 284 57 20 18.4 90 5

Mirage / SPACE STAR

CE 1.5 Litre 7 / 9 6 - on F 413 3 Vented 235 45 18 16.4 64 4

NIMBUS / SPACEWAGON / CHARIOT GRANDIS

UA, UB, UC 1984 - 91 F 219 3 Vented 242 34.5 18 16.4 86 4
UF 2.4 Litre 1/92 - 98 F 411 3 Vented 256 45.3 24 22.4 69 4
UG 7/98 - 2001 F 437 3 Vented 276 45.5 24 22.4 69 5
R 429 3 3 Vented 284 60.2 20 18 90 5

148 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SCORPION
PART NOT AVAILABLE
GE, GH, GJ, GK, GL 1978 - 84 F 211 3
REFERENCE ONLY Solid 255 28 12.5 11 80 4
R 212 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 247 48 10 8.4 90 4

SIGMA
GE 1.6, 2.0, 2.6 1978 - 80 F 210 3 Solid 229 30 13 11.4 67 4
GH, GJ, GK, GN 1980 - 87 F 205 3 Solid 256 32.5 13 11.5 80 4
R 207 3 Solid 280 73 10.5 8.8 68 4

STARION
PART NOT AVAILABLE
JA, JB, JD 5/82 - 8/87 F 400 3 Vented
REFERENCE ONLY 256 36 24 22.4 80 4
R 401 3REFERENCE
PART NOT AVAILABLE
Vented
ONLY 247 47.5 18 16.4 90 4

VERADA / DIAMANTE
KR, KS V6 ABS & non-ABS 8/91 - on F 425 3 3 Vented 276 45 24 22.4 69 5
KR, KS V6 non-ABS 8/91 - on R 422 3 Solid 258 66 10.4 8.4 90 5
KR, KS V6 Sedan with ABS 3/94 - on R 423 3 Vented 266 65.5 18 16.4 90 5
KS V6 Wagon with ABS 3/94 - on R 427 3
PART NOT AVAILABLE
Vented
REFERENCE ONLY 284 65.5 20 18.4 90 5
KE 10/96 - 6/97 F 425 3 3 Vented 276 45 24 22.4 69 5
KF, KJ 2.4, 3.0, 3.5 Litre 6/97 - on
KL (Ei, GTVi, Xi) V6 1/2003 - on R 426 3 Solid 258 56.5 10.5 8.4 90 5
KJ (II) AWD V6 1/2003 - on F 417 3 3 Vented 294 46 24 22.4 69 5
KL AWD V6 8/2003 - on R 429 3 3 Vented 284 60.2 20 18.4 90 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 149
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CANTER
CANTER 4.0DT FE659 1996 - on F 2220 3 Vented 310 55 40 114 6
R 2221 3 Vented 310 70 40 139 12

CHALLENGER
Challenger (PA) 3.0L V6 12/97 - on F 663 3 3 Vented 276 45.3 24 22.4 87 6
XS, LS - Door Wagon R 233 3 Solid 315 84 18 16.4 108 6

Express
SJ 2.4 Litre 12/94 - on F 229 3 Vented 276 45.5 22 20.4 87 6
SJ 2.0/2.5 12/94 - on F 230 3 Vented 258 33.5 22 20.4 84 5

L200 - Later models, see TRITON

MA, MB, MC, MD - 2WD 1981 - 86 F 220 3 Solid 255 34 20 18.4 84 6
MA, MC, MD - 4WD 1981 - 86 F 228 3 Vented 255 45 20 18.4 87 6
L200 2.5L 2WD Diesel F 218 3 Vented
PART NOT AVAILABLE
REFERENCE ONLY
254 39 24 22.4 87 6

L300
SA 1980 - 82 F 225 3 Vented 232 29.5 20 18.4 84 5
SB, SC, SD, SE 1982 - 9/86 F 226 3 Vented 255 34 20 18.4 84 5
SF, SG, SH, SJ 2WD 10/86 - on F 230 3 Vented 258 33.5 22 20.4 84 5
SC, SD, SE 4WD 1983 - 9/86 F 228 3 Vented 255 45 20 18.4 87 6
SF, SG, SH, SJ 4WD 10/86 - on F 229 3 Vented 276 45.5 22 20.4 87 6
WA LWB 2.4L 9/94 - on F 208 3 Vented 254 39 24 22.4 87 5

150 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

OUTLANDER / AIRTREK
ZE 2S45 AWD 2002 - 2006 F 2201 Vented 276 45.5 26 24.4 69 5
All models 2006 - on F 2201 Vented 276 45.5 26 24.4 69 5
*Check Dimensions of F 417 Vented 294 46 24 22.4 69 5
front for correct fitment* R 2209 Vented 262 60.3 10 8.4 80 5

PAJERO / SHOGUN
NA, NB, NC, ND SWB 1983 - 9/87 F 228 Vented 255 45 20 18.4 87 6
NA, NB, NC, ND LWB 1983 - 9/87 F 224 Vented 275 45 20 18.4 87 6
NE, NF, NG, NH SWB 10/87 - 92 F 232 Vented 258 45 22 20.4 87 6
NE, NF, NG, NH LWB
NF, NG, NH V6 LWB 9/88 - 92 F 229 Vented 276 45.5 22 20.4 87 6
NH, NJ V6 SOHC 1992 - on F 234 Vented 276 45 24 22.4 87 6
NJ V6 DOHC 1992 - on Check Bolt Holes - use DBA-234T if holes are tapped/threaded

NJ 3.5L 12/93 - on F 236 Vented 276 45.3 27 25.4 87 6

NF, NG, NH, NJ 5/91 - 94 R 233 Solid 315 84 18 16.4 108 6
NK 2.8L & 3.0L 15” Wheels 11/96 - 9/97 F 234 Vented 276 45 24 22.4 87 6
Check Bolt Holes - use DBA-234T if holes are tapped/threaded
NK 3.5L 6/96 - on F 236 Vented 276 45.3 27 25.4 87 6
All NK Rears 6/96 - on R 233 Solid 315 84 18 16.4 108 6
NL 2.8L 15” Wheels 6/96 - on F 234 Vented 276 45 24 22.4 87 6
Check Bolt Holes - use DBA-234T if holes are tapped/threaded

NL GLX 3.5L 15” Wheels 6/96 - on F 236 Vented 276 45.3 27 25.4 87 6
NL GLS 3.5L & NK 3.5L 6/96 - on F 237 Vented 314 45.5 24 22.4 87 6
16”,18” Wheels
All NL Rears 6/96 - on R 233 Solid 315 84 18 16.4 108 6
NL o/seas only 6/96 - on R 238 Solid 323 76 10 8 93.5 6
iO Series (QA) 1999 - on F 239 Vented 286 39 22 20 69 5
NM 3.2L T/Diesel, 3.5L V6 5/2000 - 02 F 660 Vented 290 46 26 24.4 94 6
NP 3.2L T/Diesel, 3.5L V6 11/02 - 06
Shogun 2.8DT 3.2DT, 3.5i R 661 Vented 300 72 22 20.4 94 6
NS 3.8L V6 Petrol 2006 - on F 660 Vented 290 46 26 24.4 94 6
NS 3.2L Turbo Diesel F 2216 Vented 332 56.7 28 26 94 6
Rear All Models R 2219 Vented 332 74.6 18 16 94 6
Special Note: NL Rears - check dimensionS

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 151
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MITSUBISHI - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ROSA BUS
NS 3.8L V6 Petrol 2006 - on F 2222 3 Vented 293 54 40 37.7 110 5

STARWAGON / Delica Space Gear / LZ6460 Future

WA 9/94 - on F 208 3 Vented 254 39 24 22.4 87 5
SF, SG, SH 2WD 10/86 - 8/94 F 230 3 Vented 258 33.5 22 20.4 84 5
SF, SG, SH 4WD 10/86 - 8/94 F 229 3 Vented 277 45.5 22 20.4 87 6
SJ Satellite 9/95 - on F 230 3 Vented 258 33.5 22 20.4 84 5

TRITON
ME, MF, MG, MH, MJ 2WD 1986 - on F 231 3 Vented 258 33.5 22 20.4 84 6
ME, MF, MG, MH, MJ 4WD 1986 - on F 229 3 Vented 276 45.5 22 20.4 87 6
MJ 4X2 12/94 -10/96 F 231 3 Vented 258 33.5 22 20.4 84 6
MJ 4X4 12/94 -10/96 F 229 3 Vented 276 45.5 22 20.4 87 6
MK 4X2 14inch 10/96 - on F 662 3 Vented 254 39 24 22.4 87 6
all except 3.0L V6
MK 4X2 15inch 10/96 - on F 663 Vented 276 45.3 24 22.4 87 6
MK 4X4 3.0L V6 GLX
MK 4X4 16inch GLS 6/01 - on F 237 Vented 314 45.5 24 22.4 87 6
ML 4x2, 4x4 all models 2007 - 2009 F 2208 Vented 295 46.5 28 26.4 94 6
MN 4x2, 4x4 all models 2009 - on F 2208 Vented 295 46.5 28 26.4 94 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

152 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
MORRIS - AUSTIN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Austin 1800 Mk 1, 2, 3 1964 - 75 F 080 3

PART NOT AVAILABLE
REFERENCE ONLY Solid 236 79 12.5 11.5 73 5
Morris 1100 Mk 1, 2 1963 - 67 F 082 Solid 203 61 7.7 7.3 55 4
PART NOT AVAILABLE
REFERENCE ONLY

Morris 1100 Mk 2, 3 1968 - 74 F 083 3 Solid 214 61.5 11 10.1 55 4

Morris 1300 (All Models) 1967 - 74
Morris Marina 1300, 1800 1971 - 80 F 084 3 Solid 248 46 9.5 8.6 66 4

AUSTIN HEALEY
Sprite Mk II-III (1100) 1962 - 71 F 060 3 Solid 209.8 39.5 7.5 7 63.5 4
Sprite Mk IV (1275)
Sprite Mk II-III (1100) 1962 - 71 F 061 3 Solid 209.8 60 7.7 7.3 63 4
Sprite Mk IV (1275)
3000 Mk II-III 3 LITRE 1960 - 68 F 094B 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 281 38 12.7 11.4 82.6 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 153
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

1200 / 120Y
B110 1200 1970 - 4/74 F 314 3
PART NOT AVAILABLE Solid 212 35.6 9.5 8.4 70 4
REFERENCE ONLY
B210 120Y 3/74 - 11/75
B210 120Y 12/75 - 3/79 F 310 3 Solid 219 32.5 9.6 8.6 70 4

1600, 180B
510 1600 all models 1968 - 9/72 F 306 3 Solid 232 40 10 8.4 68 4
610 180B all models 9/72 - 8/74 Small Stub Axle
610 180B all models 9/74 - 8/78 F 307 3 Solid 245 35.5 10 8.4 73 4
Large Stub Axle
610 Sedan 8/73 - 9/77 F 308 3 Solid 232 35 10 8.5 73 4
*Rare Model *
Check Dimensions

180SX
RS13 (180SX) 1.8L Turbo 1989 - 1/91 F 918 3 Vented 250 49 18 16 68 4
R 904 3 Solid 258 46.5 9 8 68 4
RS13 (180SX) 2.0L Turbo 1/91 - on F 919 3 Vented 280 49 22 20 68 4
R 904 3 Solid 258 46.5 9 8 68 4

200B
810 Local 10/77 - 7/79 F 315 3
PART NOT AVAILABLE Solid 253 48 12.7 10.5 73 4
REFERENCE ONLY
810 Import 1980 - 81
810 Local 8/79 - 4/81 F 326 3
PART NOT AVAILABLE
Solid 244 43.6 12.7 10.5 73 4
REFERENCE ONLY
(Girlock Brakes) DB1091 Pads

200SX
S14 8/94 - on F 909 3 3 Vented 280 54 30 28 68 5
R 906 3 3 Solid 258 47 9 8 68 5
S15 2000 - on F 909 3 3 Vented 280 54 30 28 68 5
R 906 3 3 Solid 258 47 9 8 68 5

240C
PART NOT AVAILABLE
230 all models 1971 - 73 F 320 3
REFERENCE ONLY Solid 271 52 12.5 10.5 81 5

154 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

240K
C110 4D 12/72 - 11/75 F 306 3 Solid 232 41 10 8.5 68 4
C110 4D 12/75 - 78 F 315 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 253 48 12.7 10.5 73 4
C110 2D 12/75 - 78 F 316 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 270 48 12.5 10.5 73 4

240Z
PART NOT AVAILABLE
240Z S30 1970 - 73 F 324 3
REFERENCE ONLY Solid 271 52 12.7 10.5 81 4

260C
PART NOT AVAILABLE
230 all models 2/73 - 10/75 F 320 3
REFERENCE ONLY Solid 271 52 12.5 10.5 81 5
330 all models 11/75 - 80 F 321 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 271 43.5 12.5 10.5 81 5

260Z
PART NOT AVAILABLE
260Z S30 1973 - 78 F 325 3REFERENCE
ONLY Solid 271 43.5 12.7 10.5 81 4

280C
PART NOT AVAILABLE
330 & 430 all models 1978 - 9/80 F 321 3
REFERENCE ONLY Solid 271 43.5 12.5 10.5 81 5
430 all models 10/80 - 84 F 322 3 Vented 250 29 20 18 81 5

280ZX
PART NOT AVAILABLE
280ZX S130 2/79 - 5/84 F 323 3 Vented 250
REFERENCE ONLY 29 20 18 81 4
280ZX S130 (Check REAR) 2/79 - 8/81 R 601 3REFERENCE

PART NOT AVAILABLE
ONLY Solid 269 69 10 8.6 68 4
280ZX S130 (Check REAR) 9/81 - 4/84 R 600 3 Solid 258 47 10 9 68 4

300C
Y 30 all models 10/83 - 85 F 613 3 Vented
PART NOT AVAILABLE 250 53 22 20 Hub 5
REFERENCE ONLY

R 905 3
PART NOT AVAILABLE
REFERENCE ONLY
Solid 266 69 10 9 73 5

300ZX
PART NOT AVAILABLE
300ZX All Z31 Models 1/84 - 9/85 F 608 3 Vented 274
REFERENCE ONLY 35.5 22 20 81 4
R 605 3REFERENCE

PART NOT AVAILABLE
ONLY
Solid 290 47 10 9 68 4
300ZX All Z31 Models 9/85 - 2/87 F 604 3 Vented 274 35.5 22 20 81 5
ZR1, ZR2 (Jap Import) 10/86 - on PART NOT AVAILABLE
REFERENCE ONLY

300ZX non-turbo Z32

Rear: ZR1, ZR2, ZX 10/85 -10/86 R 607 3 Solid 290 47 10 9 68 5
300ZX All Z31 Models 2/87 - on F 907 3 Vented 280 54 26 24 68 5
300ZR (Jap Import) 3/88 - on
300ZX All Models 10/86 - on R 927 3 Vented 282 57.2 18 68 5 20
300ZX Z32 VG30DTT 1989 - 99 F 909 3 3 Vented 280 54 30 28 68 5
R 908 3 3 Vented 297 63 18 16 68 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 155
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN - 350Z / 370Z C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

350Z
350Z 3.5L V6 (Touring model) 2003 - 05 F 954 3 3 Vented 296 49.2 24 22 68 5
R 574 3 3 Vented 292 62 16 14 68 5
350Z 3.5L V6 (17” Wheels) 10/05 - on F 2308 3 3 Vented 320 49.7 28 26 68 5
R 2309 3 3 Vented 308 62.5 16 14 68 5
350Z 3.5L V6 (Track model) 2003 - on F 4600 3 3 Vented 324 49 30 28 68 5
Brembo 4-pot front brake caliper
Brembo 2-pot rear brake caliper R 4601 3 Vented 322 62.5 22 20.2 68 5

370Z
3.7L V6 (Brembo calipers) 2008 - on F 42314 3 3 Vented 354.6 49.5 32 30 68 5
R 42315 3 Vented 350 62 20 18 68 5

BLUEBIRD
910 All Models 1981 - 86 F 609 3 Solid 250 43 12 10.5 Hub 4
R 611 3 Solid 280 77 10.5 9.5 68 4
U13 7/93 - 3/97 F 903 3 Vented 280 49.2 22 20 68 4
R 614 3 Solid 258 45 10 8 68 4

FAIRLADY
Fairlady 311, 2000 Sport 1966 - 71 F 610 3 Solid 284 44.5 10.4 9.4 76 4

GAZELLE
S12 All Models 1984 - 88 F 612 3 Vented 250 22 18 16 73 4

EXA - TWIN CAM - KN13

KN13 EXA 1.6L 2/87 - 91 F 603 3 Vented 240 45.5 18 16 61 4
KN13 EXA 1.8L 1988 - 91 F 628 3 Vented 250 45 18 16 61 4
All Rears 5/87 - 91 R 606 3 Solid 234 481 10 9 hub 4

GT-R (R35 MY10) - REFER TO SKYLINE

MAXIMA / CEFIRO
J30 All Models 1990 -11/94 F 910 3 Vented 280 49.3 22 20 68 5
2/90 -10/92 R 912 3 Solid 258 45 10 9 68 5
10/92 -11/94 R 925 3 Solid 258 44.5 9 8 68 5
A32 All Models 11/94 -10/99 F 914 3 Vented 280 50 26 24 68 5
R 915 3 Solid 278 45 9 8 68 5
A33 6 cyl 3.0L 10/99 - 10/03 F 914 3 Vented 280 50 26 24 68 5
R 915 3 Solid 278 45 9 8 68 5
J31 All Models 10/03 - on F 954 3 3 Vented 296 49.2 24 22 68 5

156 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

MICRA / MARCH
K11E All Models 5/95 - 98 F 920 3 Solid 234 45.5 12 10 59 4
R 921 Solid 240 41 7 6 61 4
K12 1.4L **Check Dims** 2007 - on F 2326 Vented 238 45 22 20 61 4

NX COUPE
B13 2 Litre DOHC 10/91 - 94 F 901 3 3 3 Vented 257 45 26 24 61 4
( ABS & non-ABS )
Check disc diameter dimensions
R 917 3 3 Solid 234 40 7 6 68 4

PINTARA (BLUEBIRD)
R31 All Models 1986 - 90 F 615 3 Vented 250 48 22 20 Hub 4

R 616 3 Solid 260 60 10.4 9.4 68 4
U12 All Models 1989 - 92 F 617 3 Vented 258 49 22 20 68 4
R 614 3 Solid 258 45 10 8 68 4

PRAIRIE
M10 All Models 1982 - 86 F 319 3 Vented 232 36.5 18.2 16 76 4

PULSAR N10
A14 - E15 1980 -11/82 F 301 3 Solid 239 40 9.5 8.6 64 4
P.C.D. 96mm
E13 10/81-10/82 F 305 3 Solid 239 40 9.5 8.5 64 4
P.C.D. 90mm

PULSAR N12 & EXA - SINGLE CAM

Import DB293 Pads 1982 - 5/87 F 302 3 Solid 240 35.5 12 11 76 4
Local & ET DB1103 Pads 1983 - 5/87 F 303 3 Solid 240 35.5 12 11 76 4
EXA Turbo 9/84 - 5/87 F 319 3 Vented 232 36.5 18.2 16 76 4
Local & ET 1983 - 5/87 R 304 3 Solid 235 36.5 10 9 hub 4

PULSAR N13
1.6 & 1.8 Litre 1987 - 91 F 603 3 Vented 240 45.5 18 16 61 4
Vector Sedan Model R 606 3 Solid 235 42 10 9 hub 4
& Hatch

SPECIAL NOTE: DBA 614 and DBA 902 share the same dimensions (page 63) but have a different p.c.d. They are not interchangeable.

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 157
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

PULSAR N14 - IMPORT & LOCAL

1.6L 8/91 - 8/95 F 628 3 Vented 250 45 18 16 61 4
R 917 Solid 234 40 7 6 68 4
2.0L 10/91 - 8/95 F 900 3 Vented 252 45 20 18 61 4
R 917 Solid 234 40 7 6 68 4
GTi-R 2.0 Litre Turbo 10/90 - 1994 F 901 3 3 Vented 257 45 26 24 61 4
R 898 3 3 Solid 258
PART NOT AVAILABLE
REFERENCE ONLY
33 9 8 68 4

PULSAR N15 / almera (uk)

1.6L 8/95 - 00 F 899 3 Vented 247 45 18 16 61 4
Almera 2.0D (UK) 1992 - 00 R 917 Solid 234 40 7 6 68 4
2.0L 8/95 - 00 F 901 3 Vented 257 45 26 24 61 4
R 902 3 Solid 258 45 9 8 68 4

PULSAR N16 / almera (uk)

N16 Sedan 1.6L, 1.8L 6/00 - on F 2300 3 Vented 257 49 22 20 68 4
N16E Hatchback 1.8L 4/01 - on F 919 3 Vented 280 49 22 20 68 4
R 2303 3 Solid 257 45 10 9 68 4
Almera Tino (UK) 2002 - on R 2301 3 3 Solid 278 45 10 9 68 4
1.8L, 2.2L (112 &136)

SERENA
PART NOT AVAILABLE
C23 2 Litre 9/92 - 97 F 913 3 Vented 257
REFERENCE ONLY 52 26 24 68 4

SILVIA
S13 Eng: CA 18 DE 5/88 - 92 F 3 918 Vented 250 49 18 16 68 4
S13 Eng: CA 18 DT (Turbo) R 904 3 Solid 258 46.5 9 8 68 4
S13 Eng: SR 20 DE, DT,1.8L 1991 - 93 F 919 3 Vented 280 49 22 20 68 4
2.0L 2 x wheel steering only R 904 3 Solid 258 46.5 9 8 68 4
S13 Eng: SR 20 DE, DT 1991 - 93 F 2338 3 Vented 252 49 20 18 68 4
4x wheel steering only *RARE* R 904 3 Solid 258 46.5 9 8 68 4
S15 2.0L non-Turbo 1999 - 2/00 F NOT AVAILABLE
S15 2.0L TURBO 1999 - on F 909 3 3 Vented 280 54 30 28 68 5
S15 ( Rear ) all models 1/99 - on R 906 3 3 Solid 258 47 9 8 68 5

158 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SKYLINE
PART NOT AVAILABLE
C210 1978 - 80 F 316 3
REFERENCE ONLY Solid 270 48 12.5 10.5 73 4
R 601 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 269 69 10 8.6 68 4
R30 1982 - 85 F 317 3 Vented 250 43 18 16 HUB 4
R30 GTS FJ20DET 1982 - 85 F 608 3
PART NOT AVAILABLE
Vented 274
REFERENCE ONLY 35.5 22 20 81 4
R 600 3 Solid 258 47 10 9 68 4
R31 Except GTS 1986 - 90 F 615 3 Vented 250 48 22 20 HUB 4
R31 GTS Import & Local 1986 - 90 F 924 3
PART NOT AVAILABLE
Vented 274
REFERENCE ONLY 47 22 20 68 4
R 616 3 Solid 260 60 10.4 9.4 68 4
R32T + R33 GTS-4 (4WD) F 953 3 Vented 280 49 26 24.2 68 4
R32 GTST 2.0L Eng:RB20DET 5/89 - 7/93 F 909 3 3 Vented 280 54 30 28 68 5
R 908 3 3 Vented 297 63 18 16 68 5
R32 GT-R Eng:RB26DET 6/89 - 8/93 F 4926 3 Vented 296 54 32 30 68 5
2.6L DOHC Twin-Turbo R 908 3 3 Vented 297 63 18 16 68 5
R32 GT-R Eng:RB26DETT 8/93 - 12/94 F 4928 3 3 Vented 324 53.75 30 28 68 5
R33+R34 GT-R Eng:RB26DETT 1/95 - on
Twin Turbo 2.6L V-SPEC R 929 3 3 Vented 300 63 22 20 68 5
(fitted with Brembo Calipers)
R33 GTST Eng:RB25DET 8/93 - 7/98 F 4963 3 Vented 296 53.75 30 28 68 5
R34 GT Eng:RB25DE 8/98 - on R 908 3 3 Vented 297 63 18 16 68 5
R34 GTT Eng:RB25DET 8/98 - on F 42304 3 Vented 310 53.75 30 28 68 5
2.5L Turbo R 908 3 3 Vented 297 63 18 16 68 5

GT-R (R35 - MY10)

3.8L Twin-Turbo 2009 - on F 52320 3 Vented 380 49.3 34 32 68 5
R 52321 3 Vented 380 62 30 28 68 5
Replacement for Original 2009 - on F 52322.1 3 Vented 380 34 32
Brembo disc rotor only R 52323.1 3 Vented 380 30 28

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 159
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Stagea
M35 **Check Dimensions** 02/03 - 08/04 F 954 3 3 Vented 296 49.2 24 22 68 5
Eng:VG25DD, VG25DET, VG30DD R 574 3 3 Vented 292 62 16 14 68 5
M35 **Check Dimensions** 08/04 - ON F 954 3 3 Vented 296 49.2 24 22 68 5
Eng:VG25DD, VG35DE INC. 350RXF R 574 3 3 Vented 292 62 16 14 68 5

STANZA
A10 Import 5/78 - 6/79 F 307 3 Solid 245 35.5 10 8.4 73 4
A10 SSS Import 5/78 - 6/79 F 308 3 Solid 232 35 10 8.5 73 4
Rare Model Check Dimensions
A10 Local up to - 6/79 F 315 3
PART NOT AVAILABLE
REFERENCE ONLY
Solid 253 48 12.7 10.5 73 4
A10 Local Girlock Brakes 7/79 - 83 F 326 3REFERENCE

PART NOT AVAILABLE
ONLY
Solid 244 43.6 12.7 10.5 73 4

SUNNY B310
A12 3 Solid 219 32.5 9.6
1979 - 81 F 310 8.6 70 4
A14, A15 1979 - 81 F 3 Solid 245 35.5 10 307 8.4 73 4
2.0 Litre GTi 10/90 - 94 F 3 3 Vented 257 45 26 901 24 61 4
R 898 3 3
PART NOT AVAILABLE
REFERENCE ONLY Solid 258 33 9 8 68 4

Tiida
All models 12/05 - on F 2328 3 Vented 260 44 22 20 68 4

160 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

ARMADA
All models 2004 - 05 F 2306 Vented 319 43.5 26 24.5 82 6
R 2307 Solid 319.5 58.5 14 12 82 6

CABSTAR
PF22 1/82 -10/87 F 313 PART NOT AVAILABLE
3 Vented 260
REFERENCE ONLY 29 20 18 81 6

DUALIS
ST & Ti 2WD Hatch + AWD 02/07 - on F 2316 3 Vented 296 44 26 24 68 5
(J10, JJ10) 1.5, 2.0 DCi
R 2331 3 3 Solid 292 62 9 8 68 5

FRONTIER
6 cyl. - 2WD 4/99 - 02 F 624 3 Vented 277 39 26 24 100 6
4WD 1998 - 02
all models - V6 2003 - 04 F 626 3 Vented 283 38 28 26 100 6

Murano
ST, TI 3.5L V6 07/05 - on F 2308 3 3 Vented 320 49.7 28 26 68 5
2313 3
R 3 Vented 308 62.8 18 16 68 5

NAVARA D21 & D22 4X2

D21 4X2 all except KA24E 9/85 - on F 620 3 Vented 250 37.5 22 20 81 6
D22 4X2 TD27 2/97 - 10/01
D21 4X2 KA24E 3/92 - on F 618 3 Vented 260 37.5 26 24 81 6
D22 4X2 Except TD27 2/97 - 10/01
D22 4X2 2.4L 4cyl DOHC 12/2001 - on
D22 4X2 3.0L V6 SOHC

NAVARA D21 & D22 4X4

D21 4X4 9/85 - 3/92 F 621 3 Vented 266 39.5 22 20 100 6
D21 4X4 3/92 - on F 618 3 Vented 260 37.5 26 24 81 6
D22 4X4 - all models 1/97 - 4/01 F 624 Vented 277 39 26 24 100 6
D22 3.0L V6 SOHC 4X4 10/01 - on F 629 Vented 300 38 28 26 100 6
D22 3.0L 4cyl T/Dies 4X4
D22 3.3L V6 SOHC 4X4 2/2003 - on

NAVARA d40 4x2, 4x4

4X2, 4X4 16” wheels 05/05 - on F 2310 Vented 295.6 38.3 28 26 68 6
4X2, 4X4 17” wheels 05/05 - on F 2312 Vented 320 38.5 28 26 68 6
4x2, 4x4 Thai Spec 05/05 - on F 2332 Vented 295.6 53 28 26 68 6

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 161
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

NOMAD
GC 22 Van 1986 - 93 F 627 3 Vented 250 30 22 20 73 4

PATHFINDER / Terrano
WD21 4 Cyl. 8/86 - 7/92 F 621 3 Vented 266 39.5 22 20 100 6
WD21 V6 8/92 - on F 624 3 Vented 277 39 26 24 100 6
R50 All Models * 9/95 - 11/98 F 626 3 Vented 283 38 28 26 100 6
R50 All Models * 11/98 - 04 F 629 3 Vented 300 38 28 26 100 6
R50 Series III 3.3L V6
R51 2.5L TD 16” wheels 2005 - on F 2310 Vented 295.6 38.3 28 26 68 6
R51 4.0L V6 Petrol 17” wheels R 2311 Vented 308 62.8 18 16 68 6
R51 2.5L TD 17” wheels 2005 - on F 2312 Vented 320 38.5 28 26 68 6
R51 4.0L V6 Petrol 17” wheels R 2311 Vented 308 62.8 18 16 68 6

PICK-UP / KINGCAB
620 2WD 1979 F 327 3
PART NOT AVAILABLE
Solid 271 44 12.5 10.5 81 6
REFERENCE ONLY
720 2WD 80 - 12/82
720 2WD 1/83 - 85 F 311 3 Vented 250 30 22 20 81 6
PART NOT AVAILABLE
REFERENCE ONLY

720 4WD + Kingcab 1980 - 3/83 F 328 3 Solid 271 60.5 12.5 10.5 104 6
720 4WD 4/83 - 85 F 312 3 Vented 267 40 22 20 100 6

PATROL / SAFARI
MQ 160, Classic 160 1/81 - 12/87 F 329 Vented 295 30 20 18 104 6
GQ Y60 non EFi 1988 - on DB321
Safari X60 Pads
GQ Y60 EFI TB42E 2/92 - on F 623 Vented 306 35.5 26 24 104 6
GQ Y60 ALL 1988 - on R 622 Vented 315 80 18 16 111 6
GU (II) Y61 (DX, ST - Wagon) 10/97 - on F 625 Vented 306 47 32 30 109 6
except 4.8L R 622 Vented 315 80 18 16 111 6
GU (II) Y61 (Ti - Wagon) 9/01 - on F 698 Vented 316 47 34 32 109 6
only 4.8L R 699 Vented 330 89 18 16 111 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

162 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
NISSAN - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

PULSAR PANEL VAN

VB11 Panel Van DB293 Pads 6/83 - 84 F 302 3 Solid 240 35.5 12 11 76 4

TERANO
R20 11/96-10/99 F 624 3 Vented 277 39 26 24 100 6

URVAN
E23 Diesel, Petrol 11/80 - 86 F 318 3 Vented 252 27.5 20 18 81 6
E24 3/87 - 93 F 618 3 Vented 260 37.5 26 24 81 6

VANETTE
C20 10/80 - 5/81 F 307 3 Solid 245 36.2 10 8.4 73 4
C20, C120 Check disc diameter 6/81 - 11/86 F 619 3 Vented 232 22 18 16 73 4
C120, GC22 Check disc diameter 1983 - 92 F 627 3 Vented 250 30 22 20 73 4

X-TRAIL
T30 (ST & Ti) 2.5L 10/2001 - 07 F 573 Vented 280 49 28 26 68 5
R 574 Vented 292 62 16 14 68 5
T31 2.0L FWD 03/07 - 2010 F 2316 Vented 296 44 26 24 68 5
R 574 Vented 292 62 16 14 68 5

XTERRA
all models 2000 - 04 F 626 3 Vented 283 38 28 26 100 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 163
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
OPEL C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Astra
TR 1.8 & 2.0 8/96 - on F 023 3 Vented 256 41.1 24 21 60 4
R 819 3 Solid 260 69 10 8 57 4
TS (City) with ABS 9/1998 - on F 815 3 Vented 280 42 25 22 70 5
TS Series II R 816 3 Solid 264 42 10 8 65 5
TS (City) without ABS 9/1998 - on F 817 3 Vented 256 41 24 21 60 4
TS Series II R 818 3 Solid 240 42 10 8 57 4
TS SRI Turbo 2002 - 04 F 2815 3 Vented 308 42.3 25.1 22 70 5
AH - CD, CDX, CDXi 2005 - on F 815 3 Vented 280 42 25 22 70 5
Coupe, Hatch, Wagon R 816 3 Solid 264 42 10 8 65 5
AH07 - SRi, Twin Top, CDTi 2007 - on F 2815 3 3 Vented 308 42.3 25.1 22 70 5
2.2L Petrol, 1.9L Diesel R 816 3 Solid 264 42 10 8 65 5
AH07 - SRi Turbo 2007 - on F 2815 3 3 Vented 308 42.3 25.1 22 70 5
2.0L Turbo R 2035 3 Solid 278 42.2 10 8 65 5

VECTRA
JR, JS, JSII - 2.0L, 2.2L, 2.5L 6/97 - 2/03 F 825 3 Vented 288 44 25 22 70 5

164 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
PEUGEOT C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

205
GTi 1.9 Litre, 1.8 TDi 1987 - on F 273 3 Vented 247 35 20.5 18.6 66 4

206
1.4, 1.6, 1.9D 1999 - 04 F 273 3 Vented 247 35 20.5 18.6 66 4
**Check 1.4L Dimensions there is a Solid front rotor that also fits this model**
1.6i 16V 2000 - 04 F 274 3 Vented 266 27.5 20.5 18.6 66 4
2.0i 16V GT /Gti / S16 1999 - 04
2.0 HDI Turbo Diesel 1999 - 04
CC 1.6i, 2.0i
**Check Dimensions**
1.6i 16V, 1.6TD 5/02 - 3/07 F 2274 3 Vented 266 34.2 22 20 66 4
2.0i 16V GTi 5/02 - 3/07
2.0 HDI Turbo-Diesel 5/02 - 3/07
All from Chassis No. 09079
“S.W. 1.6i 16V, 2.0i 16V 2.0 HDI” 2002 - 04
**Check Dimensions**
All models above 1999 - 05 R 276 3 Solid 246.5 25 8 6 71 4
1.4, 2.0i 16V GT/GTi/S16 3/04 - 3/07 F 2275 3 Vented 283 34.2 26 24 66 4
R 276 3 Solid 246.5 25 8 6 71 4

207
1.4, 1.4TD, 1.6, 1.6TD 9/06 - on F 2274 3 Vented 266 34.2 22 20 66 4
**Check Dimensions**
1.6, 1.6 Turbo, 1.6TD 9/06 - on F 2275 3 Vented 283 34.2 26 24 66 4
**Check Dimensions**
1.6 Turbo 9/06 - on F 2276 Vented 302 34 26 24 66 4
Non ABS, all models (BOSCH) 9/06 - on R TBA Solid 249 9 HUB 4
60mm internal hub hole
ABS all models (BOSCH) 9/06 - on R TBA Solid 249 9 HUB 4
62mm internal hub hole

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 165
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
PEUGEOT C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

305
GT 1.6L + GTX 1.9L 10/85 - 89 F 274 3 Vented 266 27.5 20.5 18.6 66 4

306
N3 1.8 Litre, 2 Litre 1993 - 1997 F 273 3 Vented 247 35 20.5 18.6 66 4
2.0i, 2.0i 16V 1993 - 03 F 274 3 Vented 266 27.5 20.5 18.6 66 4
Break + ABS, 1.8i 16V 1997 - 02
Break 1.9L Turbodiesel 1997 - 1999
Break 2.0 HDi Turbodiesel 1999 - 03
Cabrio 2.0i 16V 1994 - 03
Cabrio 1.8i 16V 1997 - 03
N5 Series I GTi-6 1997 - 1999 F 275 3 Vented 283 27.5 22 20 66 4
R 276 3 Solid 246.5 25 8 6 71 4

307
1.4i 2001 - 03 F 2274 3 Vented 266 34.2 22 20 66 4
1.4i HDi, 1.6i 16V (-ESP) 2001 - on
1.6i 16V HDi (-ESP) 2001 - on
2.0i 16V HDi (-ESP) 2001 - 05
1.4i 16V (-ESP) 2004 - on
1.6i 16V, 1.6i HDi (+ESP) 2001 - on F 2275 3 Vented 283 34.2 26 24 66 4
2.0i 16V (+ESP) 2001 - on
2.0i 16V HDi (+ESP) 2001 - 05
1.4i 16V (+ESP) 2004 - on
CC 2.0i 16V 2003 - on
S.W. 1.6i 16V, 2.0i 16V, 2.0HDI 2002 - on
2.0i 16V HDi 2003 - on F 2276 Vented 302 34 26 24 66 4
**Check Dimensions**
All Models (w/ Lucas system) 2001 - 04 R 2273 Solid 247 35 9 8 71.1 4
NonABS, all models (w/ Bosch system) 2001 - on R TBA Solid 249 9 HUB 4
60mm internal Hub hole
ABS, all models (w/ Bosch system) 2001 - on R TBA Solid 249 9 HUB 4
62mm internal Hub hole

308
All Models 07 - on F 2275 3 Vented 283 34.2 26 24 66 4

166 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Peugeot C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

405
1.6/i 1991 - 1996 F 274 3 Vented 266 27.5 20.5 18.6 66 4
1.8i 1992 - 1996
1.9/i 1990 - 1992
1.9i GRI / SRI 1987 - 1992
1.8L Turbodiesel, 1.9 Diesel, 2.0i 8/92 - 1996
MI 16 1.9i 16V 1987 - 1992
MI 16 2.0i 16V 8/92 - 1996

406
all models - except Coupe 1997 - on F 277 3 Vented 283 28.2 26 24 66 4
R 278 3 Solid 290 60 10 8 71 4
Coupe with Brembo Caliper 1997 - on F PART NOT AVAILABLE

R 278 3 Solid 290 60 10 8 71 4

504
504 1970 - 82 F 270 3 Solid 273 43 12.5 10.7 76 4
PART NOT AVAILABLE
504 1970 - 82 F 272 3 Vented 273
REFERENCE ONLY 43 20 18.5 76 4
PART NOT AVAILABLE
R 271 3REFERENCE
ONLY Solid 273 24.5 12 10.8 79 4

505
505 1980 - 88 F 270 3 Solid 273 43 12.5 10.7 76 4
PART NOT AVAILABLE
505 1980 - 88 F 272 3 Vented 273
REFERENCE ONLY 43 20 18.5 76 4
PART NOT AVAILABLE
R 271 3REFERENCE
ONLY Solid 273 24.5 12 10.8 79 4

604
PART NOT AVAILABLE
604 1978 - 82 F 272 3 Vented 273
REFERENCE ONLY 43 20 18.5 76 4
604 Turbo Diesel 1978 - 82 F 270 3 Solid 273 43 12.5 10.7 76 4
PART NOT AVAILABLE
604 1978 - 82 R 271 3
REFERENCE ONLY Solid 273 24.5 12 10.8 79 4

PARTNER / RANCH / LIGHT COMMERCIAL

Partner 1.4i, 1.8i, 1.9 diesel 1996 - on F 274 3 Vented 266 27.5 20.5 18.6 66 4
Ranch, Light Commercial 1996 - on
306 Light Commercial Van + ABS 1993 - on
Partner Light Commercial 1996 - on

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 167
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Pontiac C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

camaro
All models 1998 - 2002 F 2996 3 3 Vented 303 52.5 32 30.7 71 5
R 2997 3 3 Vented 305 62 26 24.7 71 5

GRAND AM
W/ Performance Pkg. WS6 1990 F 2600 3 3 Solid 246 48 22 20 59 5

G5, G5 Pursuit
w/ rear disc 2005 - 2006 F 2052 3 3 3 Vented 270 45.2 14 12 66 5
R 2053 3 3 3 Solid 315 70.4 28 26.5 100.7 6

G6
w/o ABS 2005 - 2006 F 2052 3 3 3 Vented 270 45.2 14 12 66 5
R 2053 3 3 3 Solid 315 70.4 28 26.5 100.7 6

G8
V6 2026™ 3
3 3 Vented 298 52.2 30 28
2009 F 67.5 5
R 2027™ 3 3 3 Vented 302 56 22 20 67.4 5
V8 2009 F 2028™ 3 3 3 Vented 321 52.2 30 28 67.5 5
R 2029™ 3 3 3 Vented 324 56.1 22 20 67.4 5
GXP 6.2L V8 LS3 2009 F 2604 3 3 3 Vented 355 50 32 30 67.4 5
R 2029™ 3 3 3 Vented 324 56.1 22 20 67.4 5

GTO
ALL 2004 F 040 3 3 3 3 Vented 296 83 28 25 71.5 5
R 041 3 3 3 Solid 286 78.6 16 14 70 5
ALL 2005 F 2020™ 3 3 3 3 Vented 320 83 32 30 71.6 5
R 2021™ 3 3 3 Vented 286 80 18 16 70 5

PURSUIT
w/ rear disc 2005 - 2006 F 2052 3 3 3 Vented 270 45.2 14 12 66 5
R 2053 3 3 3 Solid 315 70.4 28 26.5 100.7 6

SUNBIRD
ALL 1989 - 1991 F 2600 3 3 Solid 246 48 22 20 59 5

VIBE
2WD/4WD - w/ rear drum 2003 - 2006 F 562 3 3 3 Vented 275 49.5 25 23 55 5
2WD GT - w/ rear disc 2003 - 2006 F 562 3 3 3 Vented 275 49.5 25 23 55 5
R 563 3 3 3 Solid 269 56 9 7.5 55 5

168 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Porsche C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

911 / 912
356C 1963 - 65 F 396 3 Solid 282 35 12.5 11 107 5
PART NOT AVAILABLE
911, 911T 1965 - 69 REFERENCE ONLY

912 1.6 L 1965 - 69

911 E, T, S, SC, Sportsmatic 1969 - 83 F 394 3 Vented 282 35 20 19.1 107 5
PART NOT AVAILABLE
Carrera 2.2, 2.4, 2.7 L REFERENCE ONLY

914/6, 911 Turbo

911 E, T, S, SC, Sportsmatic 1969 - 83 R 395 3 Vented 289
PART NOT AVAILABLE
84 20 18.7 90 5
REFERENCE ONLY
Carrera 2.2, 2.4, 2.7, 3.0 L
911 Carrera 3.2 L 1984 - 9/89 F 593 3 Vented 282
PART NOT AVAILABLE
35 24 22.6 107 5
REFERENCE ONLY
911 Speedstar 3.2 L 1989 - 92
911 Carrera 2, 4 3.6 L 10/89 - on F 590 3 Vented 298 80
PART NOT AVAILABLE
28 26 103 5
REFERENCE ONLY
R 591 3 Vented 299 100 24 22 103 5

911 (993)
2 piece disc
911 3.6 Turbo 4, GT2, 03/95 - 9/97 F 52390
rotor design 3 Vented 322 72.2 32 30 103 5

911 (996)
911 3.4 Carrera, Carrera 4 06/97 - 9/01 F 2394 3 3 Vented 318 67 28 26 98 5
911 3.6 Carrera 4 10/01 - on
2 piece disc
911 Turbo, C4S 1999 - 2004 F 52386
rotor design 3 Vented 330 69.5 34 32 98 5
2 piece disc
911 Turbo F 52388
rotor design 3 Vented 350 69.5 34 32 98 5
DBA 52388 = Brake upgrade using
6 piston caliper Rear suits all models R 42397 3 Vented 330 75.5 28 26 98 5
2 piece disc
911 GT2, GT3, GT3RS 2003 - 2005 F 52396 3 Vented 350 67.5 34 32 98 5
rotor design

Rear suits all models R 42397 3 Vented 330 75.5 28 26 98 5

911 (997)
911 3.6 Carrera, 4 07/04 - on F 2394 3 3 Vented 318 67 28 26 98 5
2 piece disc
911 C2S C4S 2004 - 2010 F 52386
rotor design 3 Vented 330 69.5 34 32 98 5

Rear suits all models R 42397 3 Vented 330 75.5 28 26 98 5

2 piece disc
911 GT3, GT3RS 2005 - 2008 F 52396
rotor design 3 Vented 350 67.5 34 32 98 5
Planned
Rear suits all models R Vented 350
release 2011 34
911 GT3 incl. PCCB cars 2006 - on F 52399.1 3 Vented 380 32 32 30
Planned
Direct replacement disc rotor release
as per Original Equipment 2011
(FLAT DISC ONLY)
DBA 52399.1 Rear suits all models Planned
R Vented 350 34
release 2011

PORSCHE CONTINUED ON NEXT PAGE

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 169
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Porsche C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

924
924 2.0 L 1980 - 82 F 397 3
PART NOT AVAILABLE Solid 257 42 13 11.5 hub 5
REFERENCE ONLY

924 2.0 L Turbo 1980 - 82 F 394 3 Vented 282
PART NOT AVAILABLE
35 20 19.1 107 5
R 399 3 Vented 289
REFERENCE ONLY
71 20 18.6 103 5

CAYMAN
Cayman S 3.4L 11/05 - on F 2394 3 3 Vented 318 67 28 26 98 5

928
928 4.5 L 11/81-12/82 F 398 PART NOT AVAILABLE
3 Vented 282
REFERENCE ONLY 60 20 18 90 5
R 399 3REFERENCE
Vented 289
PART NOT AVAILABLE
ONLY
71 20 18.6 103 5
928 S4.7 L 1/80 - 8/86 RHF 597A 3 Vented 282 60
PART NOT AVAILABLE
32 30.6 90 5
LHF 597B 3 Vented 282 60
REFERENCE ONLY
32 30.6 90 5
928 S4.7 L 1984 - 9/87 R 399 3 Vented 289 71
PART NOT AVAILABLE
REFERENCE ONLY
20 18.6 103 5
928 - All models 9/86 - 8/92 RHF 392A 3 Vented 304 77
PART NOT AVAILABLE
32 30 103 5
LHF 392B 3 Vented 304 77 32 30 103 5
REFERENCE ONLY
Vane Pattern Direction
928 S4 1986 - 95 R 393 3 Vented 299 71
PART NOT AVAILABLE
REFERENCE ONLY
24 22 103 5
928 - All Models 1992 - 95 F 2392 3 Vented 322 77.5 32 30 103 5
1986 - 95 R 393 3 Vented 299 71
PART NOT AVAILABLE
REFERENCE ONLY
24 22 103 5

930
930 Turbo 3.3L 11/81 - 85 RHF 592A 3 Vented 304
PART NOT AVAILABLE 57 32 30 107 5
REFERENCE ONLY
Drill Hole Direction LHF 592B 3 Vented 304 57 32 30 107 5
930 Turbo 3.3L 11/81 - 88 RHR 598A 3 Vented 309
PART NOT AVAILABLE
82 28 26 103 5
LHR 598B 3 Vented 309
REFERENCE ONLY
82 28 26 103 5

944
944 2.5L SOHC 4/82 - 89 F 394 3 Vented 282 35 20 19.1 107 5
944 2.5L SOHC 4/82 - 89 R 399 PART NOT AVAILABLE
3 Vented 289
REFERENCE ONLY 71 20 18.6 103 5
944 S 2.5L 16V DOHC 10/87 - 88
944 Turbo 1985 - 86 R 393 PARTS
3REFERENCE
Vented 299
NOT AVAILABLE
ONLY 71 24 22 103 5
944 2.5 L Turbo 1985 - 86 F 595 3REFERENCE
Vented 298
PART NOT AVAILABLE
ONLY
45 28 26 103 5
R 596 3REFERENCE
Vented
PART NOT AVAILABLE
ONLY
299 71 24 22 103 5
944 2.5 L Turbo 9/86 - 7/89 F 949 Vented
PART NOT AVAILABLE
298 74 28 26 103 5
R 585 Vented
REFERENCE ONLY
299 100 24 22 103 5
944 All Turbo Models 8/89 - 91 RHF 392A 3 Vented
PART NOT AVAILABLE
304 77 32 30 103 5
Vane Pattern Direction LHF 392B 3 Vented
REFERENCE ONLY
304 77 32 30 103 5

170 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
Porsche C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

BOXTER
2.5, 2.7 9/96 - on F 42398 3 Vented 298 67 24 22 98 5
BoxsterS 3.2L, (986) 2000 - 2010 F 2394 3 3 3 Vented 318 67 28 26 98 5
BoxsterS 3.4L (987) + CaymanS

CAYENNE (SUV)
V6 Turbo + Cayenne S 2004 - on F 42246 3 Vented 350 69 34 32 85 5
all models (exc. Brembo caliper) R 42245 3 Vented 329 74 28 26 85 5
all models (w/ Brembo caliper) R 2249 Vented 358 73.5 28 26 85 5

proton
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

M21 1.8 L 10/97 - on F 414 3

PART NOT AVAILABLE
Vented
REFERENCE ONLY 256 45 24 22.4 64 4
R 410 3 Solid 260 41 10 8.4 64 4
Persona 1.5L 11/96 - on F 413 3 Vented 235 45 18 16.4 64 4
Satria GLI
Persona 1.6L 3
11/96 - on
Vented
PART NOT AVAILABLE
REFERENCE ONLY F
256 45 414
24 22.4 64 4
Satria XLI & GTi 1.8L R 410 3 Solid 260 41 10 8.4 64 4
Wira 1.5L 5/95 - on F 413 3 Vented 235 45 18 16.4 64 4
Wira 1.6L 5/95 - on F 414 3
PART NOT AVAILABLE
Vented
REFERENCE ONLY 256 45 24 22.4 64 4
Wira 1.5L, 1.6L ( Rear ) 5/95 - on R 410 3 Solid 260 41 10 8.4 64 4
Waja 1.6L Sedan 2001 - on F 415 3 Vented 256 45 24 22.4 69 4
R 416 3 Solid 260 41 10 8.4 90 4
Gen.2 S4PH 1.6L DOHC 2004 - on F 42140 3 Vented 266 44 22 20.4 69 4
R 2141 3 Solid 280 41 12 10.4 90 4
Jumbuck 5/2002 - on F 2200 3 Vented 256 45 24 22.4 64 4
Satria GTi - Race Spec 11/96 - on F 402B 3 3 Vented 276 45 24 22.4 69 4
(4 x 100 PCD)

RANGEROVER
Please refer to Land Rover section

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 171
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
RENAULT C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

RENAULT
PART NOT AVAILABLE
Dauphine, Caravelle, Floride 1962 - 68 F 350
REFERENCE ONLY Solid 260 40 7 6 60 3
Virage, 1.4 1976 - 80 F 345 3 Solid 227.5 38.5 10 9 83 6

RENAULT 12
R12 1971 - 76 F/R 345 3 Solid 227.5 38.5 10 9 83 6
R12 Gordini 1971 - 75 F 343 3 Vented 228 45.5 20 19 83 6
R 345 3 Solid 227.5 38.5 10 9 83 6

RENAULT 15
R15 TS 1973 - 76 F 343 3 Vented 228 45.5 20 19 83 6
R15 TL, GTL 1973 - 76 F/R 345 3 Solid 227.5 38.5 10 9 83 6

RENAULT 16
R16 (R1150) 1865 - 68 F 347 3 Solid 250 45 9 8 84 3
R16 1968 - 77 F 344 3 Solid 254 40 12 11 84 3

RENAULT 17
R17 TL, TS, Gordini 1973 - 76 R 345 3 Solid 227.5 38.5 10 9 83 6

RENAULT 18
R18 GTS (R1340, R1341) 1980 - 82 F 345 3 Solid 227.5 38.5 10 9 83 6
R18 GTS (R1350, R1351) 1982 - 83
R18 GTS (R1342, R1343) 1980 - 83 F 346A 3 Vented 238.5 46.5 20 17.7 60 4
R18 GTS (R1352, R1353) 1980 - 83
R18 All Models 1979 - 83 R 345 3 Solid 227.5 38.5 10 9 83 6

RENAULT 19
R19 GTX / TXE 7/88 - 12/95 F 351 Vented 238 41 20.1 17.7 61 4

RENAULT 20
R20 TS (R1270) 1980 - 83 F 346A 3 Vented 238.5 46.5 20 17.7 60 4
R20 TS, (R1276, R1277)

RENAULT FUEGO
GTX (R1362, R1363) 1982 - 87 F 346A 3 Vented 238.5 46.5 20 17.7 60 4
TX, GTX (R1362, R1363) 1982 - 87 F 346B 3 Vented 238.5 46.5 20 17.7 61 4

172 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
RENAULT C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CLIO
1.4i 16V +ABS,1.6i +ABS, 1.6i 16V 1998 - on F 2352 3 Vented 259 41 20.6 17.7 61 4
2.0i 16V SPORT + ABS 2000 - on F 2353 3 Vented 280 44 24 21.8 61 4
rear only fits non ABS models R 2354 Solid 238 74.6 8 7 HUB 4
Sport 2.0L 16V Turbo 2006 - on F 2350 3 Vented 312 63 28 26 61 5
Inc. RS200 20th Ann. LE,
RS 200 Cup, R27 F1,
RS197, Gordini Edition
Check Dimensions

GRAND Scenic
1.5 dCi, 1.9 dCi, 1.6 16V 6/03 - on F 2362 Vented 300 44 24 21.8 61 4
2.0 16V, 2.0T

Megane
1.6i 16V (BAO4), 2.0i 16V (BAOH) 3/99 - on F 2353 3 Vented 280 44 24 21.8 61 4
1.8i 16V, Turbodiesel 1.9 dCi 2001 - on
Turbodiesel 1.5 dCi 11/02 - on
2.0i 16V (BAOH) 1996 - 10/02 R 2354 Solid 238 74.6 8 7 HUB 4
2.0i 16V Cabriolet 1997 - 06/03
2.0i 16V (DAOH/DAO3) Coupe 11/95 - 06/03
All models exc. Sport 2005 - on F 2362 Vented 300 44 24 21.8 61 4
Check Dimensions
Sport 2.0L 16V Turbo 2005 - on F 2350 3 Vented 312 63 28 26 61 5
Inc. R26 F1, RS225,
RS225 F1, RS225 Cup
Check Dimensions

Scenic
1.4i 16V 1.6i 16V, 2.0i 16V (JA1B) 9/99 - 5/03 F 2353 3 Vented 280 44 24 21.8 61 4
Turbodiesel 1.9 dCi
1.5TD dCi, 1.6 16V 6/03 - on F 2353 3 Vented 280 44 24 21.8 61 4
Check Dimensions
1.9TD dCi, 2.0 16v, 2.0T 16V 6/03 - on F 2362 Vented 300 44 24 21.8 61 4
Check Dimensions

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 173
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
ROlls royce C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Shadow & Bentley ‘T’ 1966 - 71 F RRF 3 Solid 280 35 16 14 90 10

(NOT AVAILABLE) R RRR 3 Solid 275 40 13 12 90 10
Shadow II F 2948 3 Vented 281 44 31.5 29.5 89 10
F 2949 Vented 298.5 43.7 31.5 30 88.9 10

Rover
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

ROVER
3500 SDI 1979 - 83 F 089 3 Solid 257 75 14.5 13 75.5 5
PART NOT AVAILABLE
3500 SE, 1982 - 87 REFERENCE ONLY

Vanden Plas 1982 - 87

Quintet SU 1983 - 86 F 190 3 Solid 231 50 12 10 61 4
12.5mm Dia. Holes
416i BA1 5/86 - 90 F 187 3 Vented 242 44.5 19 17 61 4

* Range Rover - refer to Land Rover section

174 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SAAB C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

95 V4 Station Wagon 9/66 - 70 F/R 386 3 Solid 267 51 9.7 8 87.5 5

96 V4 Sports 9/66 - 70
Sonnet V4 Coupe 1967 - 70
Sonnet 97 III 1970 - 71
99 E, EMS, Coupe 1968 - 74 F/R 387 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 269 66.2 10.5 9.5 86 4
99 L, EMS, Coupe 1975 - 79 F 385 3 Solid 280 47.5 12.7 11.7 86 4
R 387 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 269 66.2 10.5 9.5 86 4

9.3 / 9.5 SERIES

9.3, 9.5 1997 - on F 825 3 Vented 288 42 25 22 70 5
Sedan / Coupe / Convert R 826 3 Solid 286 69 10 8 65.5 5
2.0L, 2.3L, 2.0L Turbo
9.3 Series F 2819 3 3 3 3 Vented 314 46 28 25 70 5
2.0L TTI (YS3F) 09/02 - on
2.0L T Convertible (YS3F) 08/03 - on
2.0L T ESTATE 03/05 - on
9.5 Series F 2815 3 3 3 3 Vented 308 42.3 25.1 22 70 5
2.3L Turbo Estate (YS3E) 7/03 - on
3.0 TiD Estate (YS3E) 7/01 - on
3.0 V6t Estate (YS3E) 10/98 - on

900 SERIES
900 Coupe, GL, GLE, GLT 1979 - 80 F 385 3 Solid 280 47.5 12.7 11.7 86 4
900 1981 - 88 F 388 3 Solid 280 65.6 12.8 11.7 86 4
900 Turbo 16 1986 - 88 F 389 3
PART NOT AVAILABLE
Vented 280
REFERENCE ONLY 70 20 18.9 86 4
900 i 1986 - 88 F 388 3 Solid 280 65.6 12.8 11.7 86 4
900 Turbo 16 1989 - 93 F 430 3 Vented 280 43 23.5 21.5 68 4
PART NOT AVAILABLE
REFERENCE ONLY
900 i 16 1989 - 93
900, 900 i 1981 - 88 R 387 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 269 66.2 10.5 9.5 86 4
900 Turbo 16 1988 - 9/93 R 432 3 Solid 258 43 9 7.5 68 4
900 i Turbo 16
900i , 900i Turbo 1994 - 97 F 433 3 Vented 284 41 24 21 70 5
R 434 3 Solid 260 69 10 8 65.5 5
900S 1996 - on F 825 3 Vented 288 42 25 22 70 5
Model 93 R 826 3 Solid 286 69 10 8 65.5 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 175
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SAAB C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

9000 SERIES
PART NOT AVAILABLE
9000 2.0 16V 1987 - 90 F 430 3 Vented 280
REFERENCE ONLY 43 23.5 21.5 68 4
9000 2.3 16V 1990 - 93 F 431 3 Vented 280 44.5 25 23 68 4
9000 Turbo 16V 1987 - 88 F 430 3
PART NOT AVAILABLE
Vented 280
REFERENCE ONLY 43 23.5 21.5 68 4
9000 Turbo 16V 1987 - 97 F 431 3 Vented 280 44.5 25 23 68 4
9000 Turbo 2.3 16V 1990 - 97
9000 All Models 1985 - on R 432 3 Solid 258 43 9 7.5 68 4

SEAT
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

Cordoba, Ibiza, Toledo1.6, 1.8L 1994 - on 3 Solid 239 35.2 F 240 12 10 65 4

Cordoba, Ibiza, Toledo 2.0L 1994 - on F 446 3 Vented 256 38.7 20 18 65 4
R 832 3 Solid 226 71.2 10 8 39.8 4
Cordoba, Ibiza, Toledo 1995 - on F 446 3 Vented 256 38.7 20 18 65 4

Ssanyong
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

MUSSO 1996 - on F 554 3 Vented 278 41 24 22 88 6

R 555 3 Solid 300 67 10.5 8.5 105 6

SKODA
Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)
No. Series Series Vented A B C D E F

octavia
Octavia 2.0 RS (1Z3) 01/06 - on F 2806 3 3 Vented 312 49.8 25 22 65 5
Octavia 2.0 RS Combi (1Z5) 01/06 - on
R 2807 3 3 Solid 285.6 48.4 11.7 10 65 5

176 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUBARU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

1400, A22, A32 All 1974 - 79 F 342 3 Solid 229 46 10 8.5 70 4
1600, A26, A27, A67 All 1974 - 81
1600 4WD, 1800, 1980 - 84 F 340 3 Solid 229 52 12.5 10 70 4
Leone DL, DLA
1600, 1800, Leone 1984 - 85 F 640 3 Vented 230 52 18 15.5 70 4
Leone DL, GL, All models 1985 - 94 F 641 3 Vented 242 44 18 16 70 4

brumby
Brumby A69 1978 - 89 F 342 3 Solid 229 46 10 8.5 70 4
Brumby AU 1985 - 93 F 640 3 Vented 230 52 18 15.5 70 4

forester
Forester Wagon SF5 3 3 3 Vented 277 57 24
8/97 - 2002 F 648 22 58 5
R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
Forester X, XS, XT 2.5L 2002 - 08 F 650 3 3 Vented 294 57 24 22 58 5
Suits 2-pot/piston caliper F 4650* 3 Vented 295 57.5 25 23 58 5
F 5010* 3 Vented 295 57.5 25 23 58 5
rear Vented R 653 3 3 3 Vented 290 67.5 18 16 58 5
rear Solid R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
Forester 2.5T 2005 - 08 F 4654-10 3 3 Vented 326 53 30 28 58 10
Forester 2.0TD 2008 - on F 650 3 3 Vented 294 57 24 22 58 5
Suits 2-pot/piston caliper F 4650* 3 Vented 295 57.5 25 23 58 5
F 5010* 3 Vented 295 57.5 25 23 58 5
R 2659 3 3 Solid 286 63.5 10 8.5 58 5

Impreza
Impreza 2WD 1993 - 99 F 645 3 Vented 242 53 18 16 58 5
Impreza 4WD 1993 - 99 F 642 3 Vented 260 57 24 22 58 5
R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
Impeza 4WD 1999 - 02 F 648 3 3 Vented 277 57 24 22 58 5
(Check Dimensions) F 642 3 Vented 260 57 24 22 58 5
R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
Impeza 4WD - GX, RX, RV - RS 2002 - 05 F 648 3 3 Vented 277 57 24 22 58 5
Sedan/Hatch 2.0L Non - Turbo R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
all models
Impreza 2.0L, 2.5AWD, 2.0 Sport 2005 - on F 650
3 3 Vented 294 57 24 22 58 5
**Check dims of front rotor, F 4650* 3 Vented 295 57.5 25 23 58 5
Some may have DBA 648** F 5010* 3 Vented 295 57.5 25 23 58 5
Rear suits till 2007 2005 - 07 R 644 3 3 3 Solid 266 67.5 10 8.5 58 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 177
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUBARU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Impreza WRX
WRX 2.0L AWD Turbo 3 3 3 Vented 277 57 24 22 58 5
1994 - 98 F 648
R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
WRX MY99 - MY00 1999 - 2000 F 650 3 3 Vented 294 57 24 22 58 5
F 4000 3 Vented 295 57.5 25 23 58 5
F 5000 3 Vented 295 57.5 25 23 58 5
R 649 3 3 Vented 266 67.5 18 16 58 5
WRX MY01 2001 F 650 3 3 Vented 294 57 24 22 58 5
F 4000 3 Vented 295 57.5 25 23 58 5
F 5000 3 Vented 295 57.5 25 23 58 5
R 653 3 3 3 Vented 290 67.5 18 16 58 5
WRX MY02 - MY05 2002 - 2005 F 650 3 3 Vented 294 57 24 22 58 5
With 2-piston front caliper F 4650 3 Vented 295 57.5 25 23 58 5
USA Spec F 5010 3 Vented 295 57.5 25 23 58 5
R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
WRX MY02 - MY05 2002 - 2005 F 650 3 3 Vented 294 57 24 22 58 5
2.0L Turbo F 4000 3 Vented 295 57.5 25 23 58 5
With 4-piston front caliper F 5000 3 Vented 295 57.5 25 23 58 5
JAP Spec R 653 3 3 3 Vented 290 67.5 18 16 58 5
WRX MY06 - MY07 2006 - 2007 F 650 3 3 Vented 294 57 24 22 58 5
2.5L Turbo F 4650 3 Vented 295 57.5 25 23 58 5
With 2-piston front caliper F 5010 3 Vented 295 57.5 25 23 58 5
USA Spec R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
WRX MY06 - MY07 2006 - 2007 F 650 3 3 Vented 294 57 24 22 58 5
2.5L Turbo F 4000 3 Vented 295 57.5 25 23 58 5
With 4-piston front caliper F 5000 3 Vented 295 57.5 25 23 58 5
JAP Spec R 653 3 3 3 Vented 290 67.5 18 16 58 5
GH SGT MY08 2.0L Turbo 06/07 - ON F 650 3 3 Vented 294 57 24 22 58 5
Japanese spec F 4650* 3 Vented 295 57.5 25 23 58 5
08 WRX 2.5L F 5010 3 Vented 295 57.5 25 23 58 5
With 2-piston front caliper 2008 - ON R 2659 3 3 Solid 286 63.5 10 8.5 58 5

* Note: Not suitable for pre 2002 models with external ABS tone ring. For these earlier models use DBA-650, DBA-4000 or DBA-5000

178 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUBARU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

IMPREZA WRX STI

WRX STI MY99 - MY00 3 3 Vented 294 57
1999 - 2000 F 650 24 22 58 5
F 4000 3 Vented 295 57.5 25 23 58 5
F 5000 3 Vented 295 57.5 25 23 58 5
R 649 3 3 Vented 266 67.5 18 16 58 5
WRX STI MY01 2001 F 650 3 3 Vented 294 57 24 22 58 5
F 4000 3 Vented 295 57.5 25 23 58 5
F 5000 3 Vented 295 57.5 25 23 58 5
R180 (190 mm Hand Brake) R 656 3 3 Vented 290 67.5 18 16 58 5
WRX STI MY02 - MY04 2002 - 2004 F 4654-10 3 3 Vented 326 53 30 28 58 10
2.0L Turbo
With Brembo calipers R 3 3 Vented 316 67.5
655-10 20 18 58 10
WRX STI MY05 2.0L Turbo 2005 F 4654-10 3 3 Vented 326 53 30 28 58 10
WRX STI MY06 - MY07 2006 - 2007 R 4655-10 3 Vented 316 67.5 20 18 58 10
2.5L Turbo
With Brembo calipers
114.3 (4.5”) Stud PCD
WRX STI MY08 2.5L Turbo 2008 - ON F 4654-10 3 3 Vented 326 53 30 28 58 10
GRB model R 42656 3 Vented 316 63.5 20 18 58 5

* Note: Not suitable for pre 2002 models with external ABS tone ring. For these earlier models use DBA-650, DBA-4000 or DBA-5000

PART SUPERCESSION for SUBARU WRX STi

DBA is now introducing a 10 stud hole pattern disc brake rotor to suit the Subaru WRX STi range
of models combining two sets of PCD’s together on the one disc:

2002-2004 – disc rotor stud hole PCD (pitch circle diameter) = 100 mm
2005-2009 – disc rotor stud hole PCD (pitch circle diameter) = 114.3 mm

DBA 4654SL-10
Part # Slotted 10 stud hole
Left pattern

The benefits:
1. Universal fitting
2. Eliminates variations in part numbers
3. Reduced stock levels

Figure 1. (right side of the page) illustrates the combined PCD

patterns, including the two smaller extraction holes.

One part fits all.

All other rotor dimensions remain the same.

Figure 1.

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 179
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUBARU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

liberty
BC6 14” Wheels 10/89 - 94 F 642 3 Vented 260 57 24 22 58 5
GX incl. 4WD 6/94 - 9/98 R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
GX SKI-FX LE 7/96 -10/96
Heritage incl. 4WD 2.0 Litre 6/94 -11/96
LX & 4WD 6/94 - on
Rallye 11/94 -11/96
Ski FX Enduro 5/97 - 8/97
Touring 3/96 - 11/96
Rear for all above models
RS Turbo EJ20 2.0L Turbo 1990 - 93 3 3 3 Vented 277 57 24
F 648 22 58 5
R 649 3 3 Vented 266 67.5 18 16 58 5
RX AWD, LE + S port 11/96 - on F 648 3 3 3 Vented 277 57 24 22 58 5
Heritage 4WD 2.45 Litre R 649 3 3 Vented 266 67.5 18 16 58 5
All sedan/wagon models 10/98 - 02 R 657 3 3 Solid 290 67.5 10 8.5 58 5
Liberty B4 (2003 model) 2002 - 2003 F 650 3 3 Vented 294 57 24 22 58 5
Suits 2-pot/piston caliper F 4650* 3 Vented 295 57.5 25 23 58 5
F 5010* 3 Vented 295 57.5 25 23 58 5
R 653 3 3 3 Vented 290 67.5 18 16 58 5
Liberty B4 Blitzen 2.0R BL5 6/2003 - on F 2650 3 3 3 3 Vented 316 56.7 30 28 58 5
Liberty 3.0R Spec B 2006 R 653 3 3 3 Vented 290 67.5 18 16 58 5
GT/L 2000 - 01 F 648 3 3 3 Vented 277 57 24 22 58 5
R 657 3 3 Solid 290 67.5 10 8.5 58 5
GT-LTD 2001 F 650 3 3 Vented 294 57 24 22 58 5
F 4650 3 Vented 295 57.5 25 23 58 5
F 5010 3 Vented 295 57.5 25 23 58 5
R 657 3 3 Solid 290 67.5 10 8.5 58 5
L/L-S 2002 - 04 F 648 3 3 3 Vented 277 57 24 22 58 5
R 657 3 3 Solid 290 67.5 10 8.5 58 5
GT/GT-LTD (2 pot front) 2002 - 04 F 650 3 3 Vented 294 57 24 22 58 5
F 4650 3 Vented 295 57.5 25 23 58 5
F 5010 3 Vented 295 57.5 25 23 58 5
R 657 3 3 Solid 290 67.5 10 8.5 58 5

* Note: Not suitable for pre 2002 models with external ABS tone ring. For these earlier models use DBA-650, DBA-4000 or DBA-5000

180 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUBARU C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

LIBERTY (continued)
GT/GT-LTD (4 pot front) 2002 - 04 3 3 Vented 294 57 24
F 650 22 58 5
F 4650 3 Vented 295 57.5 25 23 58 5
F 5000 3 Vented 295 57.5 25 23 58 5
R 657 3 3 Solid 290 67.5 10 8.5 58 5
2.5i - except. GT 2005 F 648 3 3 3 Vented 277 57 24 22 58 5
R 2661 3 Solid 274 67.5 10 8.5 58 5
GT 2005 - 06 F 2650 3 3 3 3 Vented 316 56.7 30 28 58 5
R 653 3 3 3 Vented 290 67.5 18 16 58 5
GT by STi 2007 - 08 F 4654-10 3 Vented 326 53 30 28 58 10
Brembo Calipers Check Dimensions R 4655-10 3 Vented 316 67.5 20 18 58 10
GT 2010 F 2650 3 3 3 3 Vented 316 56.7 30 28 58 5

ouTback
LE Wagon 648
3 3 3 Vented 277 57 24
9/96 - 6/98 F 22 58 5
R 644 3 3 3 Solid 266 67.5 10 8.5 58 5
All models 10/98 - 03 F 648 3 3 3 Vented 277 57 24 22 58 5
**Check Front Diameter** R 657 3 3 Solid 290 67.5 10 8.5 58 5
All models 2003 - 05 F 650 3 3 Vented 294 57 24 22 58 5
Outback H6 1998 - 03 F 4650* 3 Vented 295 57.5 25 23 58 5
**Check Front Diameter** F 5010* 3 Vented 295 57.5 25 23 58 5
R 653 3 3 3 Vented 290 67.5 18 16 58 5
**Check Rear Thickness** R 657 3 3 Solid 290 67.5 10 8.5 58 5
2.5L & 3.0L 2005 - on F 650 3 3 Vented 294 57 24 22 58 5
R 2661 3 Solid 274 67.5 10 8.5 58 5

sherpa
PART NOT AVAILABLE
Sherpa KM3 2 Cyl 10/82 - 1/88 F 646 3
REFERENCE ONLY Solid 212 28 10 8.5 65 4
Sherpa KN3 4 Cyl 2/88 -12/89 F 647 3
PART NOT AVAILABLE Solid 212 18 9 7.5 65 4
REFERENCE ONLY
KN4 Fiori 12/89 -10/92

SVX
SVX 3/92 - 8/97 F 652 3 Vented 301.1 57 28 26 58 5
PART NOT AVAILABLE
R 651 3
REFERENCE ONLY Solid 290 67.5 10 8.5 58 5

SUBARU REAR UPGRADE

316mm Sti rear rotor to suit 3/92 - 8/97 R 2657 3 3 3 Vented 316 67.5 20 18 58 5
Subaru’s with 170mm
handbrake

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 181
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUBARU WRX UPGRADE C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

subaru rear upgrade

316mm Sti rear rotor to suit 1998 - on R 2657 3 3 Vented 316 67.5 20 18 58 5
Subaru’s with 170 mm handbrake

Gravel Spec Rear Rotor 2002-2007 R 656-10 3 3 Vented 290 67.5 18 16 58 10

290mm disc w/ 190mm handbrake
MY02-MY07 WRX STi

Up to 2000 WRX : requires caliper adapter bracket (BSM) and Sti rear Brembo calipers.
Up to 2002 Forester : requires caliper adapter bracket (BSM) and Sti rear Brembo calipers.
Up to 2002 Liberty : requires caliper adapter bracket (BSM) and Sti rear Brembo calipers.
From 2000 WRX : requires backing plate to be modified and Sti rear Brembo calipers.

182 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUZUKI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Hatch SS80 V 1981 - 85 F 511 3

PART NOT AVAILABLE
Solid 213 33.5 11 10 86 4
REFERENCE ONLY
Mighty Boy SS40 T 1984 - 88 F 511 3 Solid 213 33.5 11 10 86 4
Super Carry SK410 1985 - 88 F 012 3 Solid 215 33.5 10 8 86 4

baleno
1.6 Litre, GA, GL, GLX, GS 4/95 - on F 519 3 Vented 235 50 20 18 60 4
GTX 1.8 Litre 3/96 - on F 520 3 Vented 246 50 20 18 60 4
R 521 3 Solid 240 33 10 8 58 4

CARRY VAN/UTE
1.3 Litre GA413 1999 - on F 522 3 Vented 231 44 17 15 60 4

CINO / IGNIS
Cino SF413 1.3L 3/5Dr 1994 - on F 022 3 Vented 231 50 17 15 64 4
Ignis 1.3 Litre 3/5Dr, RG413 10/2000 - on F 523 3 Vented 257 49 17 15 60 4

Liana
“1.3, 1.5, 1.6, 1.8L sedan & Hatch” 11/2001 - on F 520 3 Vented 246 50 20 18 60 4

SAMURAI
1.3 (SJ70) 1998 - on F 513 3 Solid 290 46.5 10 8 107 5

Sierra / JIMNY
1.0 4WD SJ40, SJ410, SJ413 1983 - 86 F 510 3 Solid 290 46.5 10 9 107 5
1.3 4WD SJ50, SJ70, SJ80 10/84 - 1/96 Flange Thickness 7mm
Stockman MG 410 Ute 1990 -1999
413 SJ80 4/96 -10/98 F 513 Solid 290 46.5 10 8 107 5
Jimny SWB 1.3 SN413, 513 1998 - on F 513 Solid 290 46.5 10 8 107 5
Flange Thickness 6mm

Wagon R 1.0 SR410 1997 - 98 F 515 Vented 231 49 17 15 60 4

Swift
SA310. SA413 2/85 - 88 F 012 3 Solid 215 33.5 10 8 86 4
PART NOT AVAILABLE
GT i SA413, AA33S 10/86 - 88 F 512 3REFERENCE
Vented 231
ONLY 52 17 15 64 4
SF310, 413 1989 - 94 F 022 3 Vented 231 50 17 15 64 4
SF416, SF413, GTi, Sedan 1989 - 98 F 516 3 Vented 250 47 18.5 16.5 64 4
PART NOT AVAILABLE
GTi SF413 1989 - 98 R 517 3
REFERENCE ONLY Solid 240 35 10 8 64 4
1.6L 3D & 5D exc. Sport 2004 - on F 2584 3 Vented 252 40 20 18 60 4

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 183
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
SUZUKI C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Vitara
JX, JLX SWB SE 416 1988 - 98 F 513 Solid 290 46.5 10 8 107 5
X90 SZ 416 2 Door 1.6L 1996 - 97 Flange Thickness 6mm

4 Door “Estate” LWB 1991 - 98 F 514 3 Vented 287 46 17 15 107 5

JLX Estate 2.0L V6 SV620 1996 - 4/98 F 518 3 Vented 310 46 22 20 107 5

GRAND VITARA
Grand 1.6L SQ416 10/98 - 06 F 524 3 Vented 287 29 17 15 108 5
Soft-top
Grand 2.0L SQ420 SWB 10/98 - 06 F 578 3 Vented 287 29 17 15 107 5
Hard-top
Grand 2.0L SQ420W LWB 4/98 - 06 F 579 3 Vented 310 29 22 20 108 5
+ 2.5L SQ625W + XL-7
Grand Vitara - all models 2006 - on F 2580 Vented 295 49.5 25 23 62 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

184 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Aurion v6
3.5L V6 (GSV40R) 11/06 - on F 2709 3 3 3 Vented 296 49.3 28 25 62 5
R 2707 3 3 3 Solid 286 65 10 8.5 62 5

AVALON
MCX10R - V6 3.0L DOHC 07/00 - 08/03 F 735 3 3 Vented 275 49.5 28 26 62 5
all models rear 07/00 - 08/03 R 757 3 Solid 291 65.5 9 8 62 5
all models rear 09/03 - on R 2707 3 3 3 Solid 286 65 10 8.5 62 5
all models USA 1995 - 04 F 735 3 3 Vented 275 49.5 28 26 62 5

AVENSIS VERSO (ACM20/21)

GLX, Ultima - 7 seater 5/01 - on F 735 3 3 Vented 275 49.5 28 26 62 5
(MPV Australian Model) R 697 3 Solid 291 68.5 12 10.5 62 5

CAMRY
SV11 1982 - 86 F 149 3 Vented 243 45 22 21 54 5
SV20 Series I, II 1987 - 10/92 F 730 3 Vented 255 47.5 22 21 54 5
SV21, SV22 R 741 3 Solid 269 65 10 9 54 5
VZV20 Series I, II 2/88 - 10/92 F 732 3 Vented 255 48 25 24 54 5
VZV21, VZV22 R 741 3 Solid 269 65 10 9 54 5
SDV10, SVX10 4 Cyl 11/92 -7/97 F 733 3 Vented 255 49 28 26 62 5
VCV10, VDV10 Vienta V6 11/92 -7/97 F 735 3 3 Vented 275 49.5 28 26 62 5
SDV10, VDV10 All Sedans 11/92- 7/97 R 736 3 Solid 269 65 10 9 62 5
VDV10 V6 All Wagons 11/92 -7/97 R 734 3 Solid 288 65 10 9 62 5
SXV20 7/97 - 2002 F 733 3 Vented 255 49 28 26 62 5
MCV20 7/97 - 2002 F 735 3 3 Vented 275 49.5 28 26 62 5
Rear disc fits all sedans and wagons R 736 3 Solid 269 65 10 9 62 5
3.0L V6 (MCV36R) 8/02 - 8/06 F 735 3 3 Vented 275 49.5 28 26 62 5
2.4L 4cyl (ACV36R)
Rear fits all sedans & wagons R 2707 3 3 3 Solid 286 65 10 8.5 62 5
3.0L V6 (MCV30) -16inch wheels 07/2001 - on F 2705 3 3 Vented 296 49.3 28 26 62 5
(Europe & USA) R 2711 3 Solid 269 65 12 10.5 62 5
2.4L CYL (ACV40R) 06/06 - on F 2709 3 3 3 Vented 296 49.3 28 25 62 5
R 2707 3 3 3 Solid 286 65 10 8.5 62 5
acv40, GSV40 3 3 3 Vented 296 49.3 2006 - on F 2709 28 25 62 5
2713 3 Solid 281 67
euro Spec R 10 8.5 62 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 185
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CELICA
TA 22 1971 - 7/77 F 139 3 Solid 228 17.9 10 9 64 4
RA 23, RA 28 Liftback 1976 - 7/77 F 140 3 Solid 254 16 12.7 11.5 73 4
RA 40, RA 40 B 8/77 - 7/81
RA 60, Coupe, Liftback 8/81 - 9/83 F 146 3 Vented 258 26 20 19 76 4
SA 63, 2.0 L 10/83 - 84
RA 65, 2.4 L 10/84 - 85
ST 162 SX, GTS, 2.0 GT Coupe 8/85 - 8/89 F 739 3 Vented 258 47.5 22 21 54 5
ST 162 ST 10/86 - 8/89 F 740 3 Vented 243 48 22 21 54 4
ST 184 2WD, 2.0 GT Coupe 10/89 - 8/91 F 742 3 Vented 255 46 22 20 54 5
ST 184 2WD 8/91-11/93 F 743 3 Vented 278 46
PART NOT AVAILABLE
25 23 54 5
REFERENCE ONLY
ST 185 4WD (incl. Group A)
ST 162 SX, 2.0 GT Coupe 8/85 - 8/89 R 741 3 Solid 269 65 10 9 54 5
ST 184 10/89 -11/93
ST 185 4WD (Incl. Group A) 10/89 -11/93 R 744 3 Solid 288 60 10 9 54 5
PART NOT AVAILABLE
ST 204 2WD & GT 11/93 - 8/99 F 747 3REFERENCE
Vented 275
ONLY 49 28 26 55 5
11/93 - 8/95 R 741 3 Solid 269 65 10 9 54 5
8/95 - 8/99 R 764 3 Solid 269 65 9 8 55 5
ST 205 4WD 2/94 - on F 560 3 3 Vented 315 59 32 30 55 5
PART NOT AVAILABLE
R 561 3REFERENCE
Vented 315
ONLY 59 16 15 55 5
ZZT231 1.8L DOHC 11/99-06/00 F 562 3 3 Vented 275 49.5 25 23 55 5
1.8 WTI 190 BHP 2000 - on
R 563 3 3 Solid 269 56 9 7.5 55 5

186 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

COROLLA / RUNX / ALLEX

PART NOT AVAILABLE
KE 10#, KE 20# 3/68 - 7/74 F 141 3REFERENCE
ONLY Solid 200 36 10 9 64 4
KE 30#, KE 50# Series with 8/74 - 9/81 F 142 3 Solid 218 30 10 9 64 4
Imported Brakes
KE 30#, KE50#, KE 70, AE 71 10/81-12/84 F 144 3 Solid 218 30 12.7 11.5 64 4
Series with Local Brakes
KE 70 Panel Van 10/81- 9/83 F 145 3 Solid 228 32 12.7 11.5 64 4
AE 71 Panel Van 9/83 -12/84 F 700 3
PART NOT AVAILABLE Solid 234 38 12.5 11.5 64 4
REFERENCE ONLY
AE 86 Sprinter 5/83 -11/84
AE 80, 82 SOHC 1985 -12/88 F 701 3 Solid 243 48 13.5 12.5 54 4
AE 82 D.O.H.C 1986 -12/88 F 702 3 Vented 243 48 18 17 54 4
R 703 3 Solid 242 37 9 8 54 4
AE 90, 92 S.O.H.C. 2/89 -10/94 F 701 3 Solid 243 48 13.5 12.5 54 4
AE 90, 92, 93 D.O.H.C. 8/89 - 6/91 F 704 3 Vented 238 48 18 17 54 4
AE 95 4WD 2/88 - 94
AE 92 SX 8/89 - 6/91 R 703 3 Solid 242 37 9 8 54 4
(Eng:4AGE) Fuel Injected
AE 92 GT, GS, ULTIMA 6/91 - 10/92
(Eng:4AGE) Fuel Injected
AE 93 DOHC 6/91 -10/94 F 708 3 Vented 258 48 22 20 54 4
AE 93 (Eng:4AGE) Fuel Injected 10/92 - 94 R 703 3 Solid 242 37 9 8 54 4
AE 101 2/94 - 7/99 F 711 3 Vented 238 48 22 20 55 4
AE 102, 7/94 - 7/99 F 709 3 Vented 255 48 22 20 55 4
AE 102 Sprinter 2/94 - 5/96
AE 112 Import + turbo 5/97 - 2001
R 710 3 Solid 266 37 9 8 55 4
ZZE 122 - all models 12/01 - on F 712 3 Vented 255 49.5 25 23 55 4
(Except Sth African model) R 713 3 Solid 269 56 9 8 55 4
ZZE 122 - Sth African model 12/01 - on F 712 3 Vented 255 49.5 25 23 55 4
R 2719 3 Solid 258 56 9 8 55 4
ZZE 123 - Sportivo 2003 - 7/07 F 759 3 Vented 275 50 25 23 55 4
Corolla Verso 2.0L (UK)
Toyota Corolla ZRE 152 07/07 - on F 2742 3 Vented 275 46.3 22 19 62 5
R 2743 3 Solid 259 30.5 9 7.5 62 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 187
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

CORONA
RT 40, RT 40 L 1967 -1/70 F 137 3 Solid 241 56 10 9 74 4
RT 80, RT 81 2/70 - 7/73 F 139 3 Solid 228 17.9 10 9 64 4
RT 104, RT 118 8/73 - 9/79 F 138 3 Solid 266 42 12.7 11.5 76 4
XT 130, XT 131 10/79 - 5/83
RT 132, RT 133 2/82 - 5/83
ST 141 2.0 L, RT 142 2.4 L 6/83 - 4/87 F 705 3 Solid 250 25 12.7 11.5 76 4
PART NOT AVAILABLE
ST 141 2.0 L DB1098 Pads 6/83 - 4/87 R 706 3REFERENCE
ONLY Solid 280 79 10.5 9.4 60 4
PART NOT AVAILABLE
RT 142 with IRS 10/85 -12/86 R 707 3REFERENCE
ONLY Solid 269 60.5 10 9 60 4

CORONA MKII
RT 72 9/68 - 12/71 F 143 3 Solid 243 53.5 10 9 74 4
MX 10, 13, 22, 23 1972 - 11/76 F 138 3 Solid 266 42 12.7 11.5 76 4

CRESSIDA
MX 32, MX 36 12/76 - 8/80 F 138 3 Solid 266 42 12.7 11.5 76 4
MX 62 9/80 - 7/84 F 720 3 Vented 248 28.5 18 17 76 4
MX 73 8/84 - 8/88 F 721 3 Vented 248 40 22 21 76 4
PART NOT AVAILABLE
R 722 3REFERENCE
Vented 269
ONLY 61 18 17 60 4
MX 83 9/88 - 8/90 F 570 3 Vented 256 68 20 19 60 5
PART NOT AVAILABLE
MX 83 8/90 - 2/93 F 572 3REFERENCE
Vented 256
ONLY 68 22 21 60 5
PART NOT AVAILABLE
MX 83 9/88 - 2/93 R 571 3REFERENCE
ONLY Solid 272 66 10 9 60 5

CROWN
MS 65 Sedan 2/71 - 9/74 F 724 3 Solid 266 42 12.7 11.3 76 5
MS 83 Wagon, MS 85 1974 - 78
MS 85 Sedan All Except Royal 2/78 - 8/79 F 727 3 Vented 252
PART NOT AVAILABLE 26 20 19 76 5
REFERENCE ONLY
MS 112 Royal 4/79 - 7/83
PART NOT AVAILABLE
MS 85, MS 112 11/75 - 7/83 R 725 3REFERENCE
ONLY Solid 261 60 12.5 11.5 67 5
PART NOT AVAILABLE
MS 123 8/83 - 6/86 F 728 3REFERENCE
Vented 252
ONLY 40 20 19 76 5
PART NOT AVAILABLE
Internal Drum = 167mm R 729 3REFERENCE
Vented 268
ONLY 64 18 17 67 5
MS 123 Royal 8/83 - 6/86 R 731 3 Solid 269 65 12 11 67 5

ECHO / PLATZ
NCP 10, NCP 12 10/99 - on F 723 3 Vented 235 43 18 16 55 4
all models USA 2001 - 04 F 753 3 Vented 255 43.25 20 18 55 4

188 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

LEXCEN
VN 1, 3, VP 1, 3 6/89 - 5/92 F 015 3 3 Vented 270 82 22 20* hub 5
Except ABS
VP 1, VP 3 5/92 - 7/92 F 025 3 3 Vented 270 82 23 20* hub 5

VP 1, VP 3 7/92 - 5/93 F 027 3 3 Vented 290 82 23 20* hub 5

Including ABS
VR, VS 6/93 - on F 035 3 3 Vented 289 83 23 20 70 5
VN 1, 3, VP 1, 3 except IRS 6/89 - 5/93 R 016 3 3 Solid 279 83 10.5 8.5* 70 5
VR, VS except IRS 6/93 - on
VP with IRS 9/91 - 5/93 R 026 3 3 Solid 279 67 10.5 8.5 70 5
VR, VS with IRS 6/93 - on R 036 3 3 Solid 279 86 10.7 8.5 70 5

MR2 / MR-S
AW 11 11/87 - 89 F 750 3 Vented 258
PART NOT AVAILABLE 47 22 21 54 4
REFERENCE ONLY
non-turbo USA 6/86 - 12/89
R 751 3 Solid 258 40.5 10 9 54 4
SW 20 12/89 -12/91 F 580 3 Vented 258 47.5 25 24 62 5
PART NOT AVAILABLE
non-turbo USA 1/90 - 95 REFERENCE ONLY

turbo USA 90 - 12/91

PART NOT AVAILABLE
R 581 3REFERENCE
Vented 263
ONLY 45 16 15 62 10
SW 20 12/91 - on F 582 3 Vented 275
PART NOT AVAILABLE 47 30 28 62 5
REFERENCE ONLY
turbo USA 1992 - 95
R 583 3 Vented 281 46.5 22 21 62 10
SPYDER turbo & non-turbo 12/99 - on F 753 3 Vented 255 43.25 20 18 55 4
( ZZW30R ) R 754 3 Vented 263 41.5 16 15 55 4

PASEO
EL 44 1.5L Coupe 4/91 - 94 F 695 3 Vented 254 43 18 17 55 4
PART NOT AVAILABLE
8/92 - 94 R 696 3
REFERENCE ONLY Solid 240 80 9 8 hub 4
EL54 8/95 - on F 695 3 Vented 254 43 18 17 55 4
PART NOT AVAILABLE
R 696 3
REFERENCE ONLY Solid 240 80 9 8 hub 4

PRIUS
HNW11R 4D Sedan 1.5L 2001 - 2/02 F 712 3 Vented 255 49.5 25 23 55 4
R 713 3 Solid 269 56 9 8 55 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 189
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SECA
AE 82 SOHC, AE 93/94 Non SX 9/85 -12/88 F 701 3 Solid 243 48 13.5 12.5 54 4
AE 82 DOHC 1986 -12/88 F 702 3 Vented 243 48 18 17 54 4
R 703 3 Solid 242 37 9 8 54 4
AE 93 SX D.O.H.C. 8/89 - 6/91 F 704 3 Vented 238 48 18 17 54 4
AE 93 SX D.O.H.C. 6/91 - 10/94 F 708 3 Vented 258 48 22 20 54 4
8/89 - 10/94 R 703 3 Solid 242 37 9 8 54 4
AE 101 2/94 - 7/99 F 711 3 Vented 238 48 22 20 55 4
AE 102 7/94 - 7/99 F 709 3 Vented 255 48.5 22 20 55 4
R 710 3 Solid 266 37 9 8 55 4

SOARER
JZZ30 Eng: 1JZGTE 2.5L TURBO 1991 - on F 4748 3 Vented 296 51 32 30 62 5
UZZ32 Eng: 1UZFE 4.0L V8
(active susp., 4 wheel steer)

( check your dimensions ) R 746 3 3 Vented 307 67 16 15 62 5

JZZ31 Eng: 2JZGE 3.0L 1994 - on F 568 3 Vented 275 49.5 28 26 62 5
UZZ30 Eng: 1UZFE 4.0L V8 1991 - on
(coil susp., 2 wheel steer)

UZZ31 Eng: 1UZFE 4.0L V8

air susp., 2 wheel steer)

( check dimensions ) R 586 3 Vented 291 67.5 16 15 60 5

STARLET
EP 91 1996 - on F 714 3 Vented 238 43 18 17 55 4

190 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

SUPRA (GTE = turbo : TT = Twin Turbo : GE = non turbo : NA = Standard Model)

MK II MA 61 8/81 -12/85 F 146 3 Vented 258 26 20 19 76 4
R 717 3
PART NOT AVAILABLE
Vented 266
REFERENCE ONLY 60.5 18 17 60 4

SUPRA (MK III) JZA70

MA-70, MA-71 1986 - 5/93 F 715 3 Vented 300 53.5 22 21 60 5
7M-GTE 3.0iL Turbo (TT)
7M-GE 3.0iL (NA) R 716 3 Vented 291 68.5 18 17 60 5

SUPRA (MK IV) JZA80 ( GZ, RZ, RZ-S, SZ, SZ-R - 3.0-litre twin-cam 24-valve)
Jap 2JZ-GTE TT 2 pot caliper 5/93 - 1995 F 4748 3 Vented 296 51 32 30 62 5
Jap 2JZ-GE (NA) 2 pot caliper 5/93 - on
Export 2JZ-GE (NA) 2 pot caliper 5/93 - on
1 pot caliper on the rear 16 inch rim’s R 746 3 3 Vented 307 67 16 15 62 5
Export 2JZ-GTE TT 4 pot caliper 5/93 - 10/98 F 4718 3 3 Vented 323 50 30 28 62 5
Export 2JZ-GE (NA) 4 pot caliper 5/93 - on
Jap 2JZ-GTE TT 4 pot caliper 1995 - on
2 pot caliper on the rear 17 inch rim’s R 719 3 3 Vented 324 67.5 16 15 62 5

T-18
TE 72 SE 8/79 - 5/83 F 148 3 Solid 230 24 12.7 11.5 64 4

yaris verso
T-SPIRIT (UK) 2003 - on F 2708 3 Vented 255 43.3 20 18 55 4
YARIS - all models (Australia) 2003 - on F 2718 3 Vented 255 46.5 22 19 55 4

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 191
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

4 runner
2WD 8/89 - 95 F 780 3 Vented 289 64.5 20 18 100 6
TURBO 1986 - 98
4WD - Turbo 1986 - 87
4WD - exc. Turbo 6/91 - 10/95
LN, YN 61 4 Runner 8/85 - 3/89
LN, YN, VZN 130 4 Runner 8/89 - 91
RN 61 4 Runner 1988 - 91
4WD - exc. Turbo 8/91 - 95 F 775 3 Vented 291 66 25 23 100 6
KUN, GGN, TGN 2005 - on F 2714 Vented 297 67 25 23 108 6
GRN21#, UZN21# LIMD 6/05 - on F 2716 Vented 319 67.5 28 26 108 6
SR5, UZN210 LIMD R 793 Vented 312 68 18 16 106 6

BLIZZARD
LD 10 4WD 1982 - 4/84 F 292 3 Solid 277 30 12.5 11.5 96 5

COASTER
RB 20 5/82 -1/93 F 770 3 Vented 300 49 30 29 106.5 5
BB 20, BB 21 5/82 -1/93
HB 30, HZB
BB 40, HZB 50 1/93 - on F 771 Vented 296 101 35 33 126 5

DYNA 100, 150 SERIES
LH 80R. YH 81-100 8/85 - 3/88 F 156 3 Vented 257 47 25 24 84 5
YY 5#, 6#, LY 6#-150 8/85 - 94 F 772 3 Vented 258 52 25 24 91 6

DYNA 200, 300, 400 SERIES

BU, YU, WU, BU 100 9/84 - on F 770 3 Vented 300 49 30 29 106.5 5
All except WU 90

FJ CRUISER
all models 2006 - on F 2716 Vented 319 67.5 28 26 108 6
R 793 Vented 312 68 18 16 106 6

FORTUNER / VIGO / PRERUNNER

all models 2005 - on F 2714 Vented 297 67 25 23 108 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

192 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HI-ACE
RH 11, 20, 22, 32, 42 12/81 - 11/82 F 155 3 Vented 252 26.5 20 19 79 5
LH 11, 20, 30 12/81 - 7/85
YH 5, 6, 7, LH 5, 6, 7 12/82 - 7/89 F 156 3 Vented 257 47 25 24 84 5
LH, RZH 103, 113, 125, 184 8/89 - on F 766 3 Vented 255 47 25 23 84 5
Hi-Ace, 11/94 - on F 767 3 Vented 285 46 28 26 84 5
LH162, LH172 15” wheels 8/00 - on
SB RCH 12 6 stud holes 8/95 - on F 768 3 Vented 285 46 28 26 84 6
KDH, TRH 2005 - on F 2732 3 Vented 285 48.7 28 26 105 6

HIGHLANDER - refer to kluger

HI-LUX 2WD
RN 30, 31, 40, 41 8/78 - 7/83 F 155 3 Vented 252 26.5 20 19 79 5
LN 30, 40
RN 41, RMSQ SR5 8/78 - 7/83 F 152 3 Solid 266 43 12.7 11.5 79 5
YN 57 SR5 8/85 - 3/87 F 781 3 Vented 248 46 22 21 84 5
RN 90 ( rare model ) 8/88 - 7/97 F 783 3 Vented 254 46 22 20 84 5
YN56 1.8L 8/83 - 88 F 156 3 Vented 257 47 25 24 84 5
RN 50, YN 50 Series 8/83 - 3/89
YN85/90 1.8L 1989 - 97
LN50/51/55/56 2.2L & 2.4L 8/83 - 88
RN 85 8/88 - 8/97
LN85/90 2.4L Diesel 8/97 - on
RZN 147, 149 8/97 - on
LN 147, 152 8/97 - on
KUN 10#, GGN 15# 8/04 - 07 F 2715 3 3 Vented 255 58.6 28 26 62 5
LAN 15#, TGN 15# R DRUM
KUN 10#, GGN 15# 4/07 - on F 2740 3 3 Vented 275 58.6 28 26 62 5
LAN 15#, TGN 15# R DRUM

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 193
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

HI-LUX 4WD / 4 RUNNER / SURF / SW4

RN 36,46 1/79 - 8/80 F 153 3 Solid 302 49 12.7 11.5 100 6
10.5mm Stud Holes
RN 36, 45, 46 8/80 - 7/83 F 154 3 Solid 302 49 12.7 11.5 100 6
LN 36, 46 8/80 - 7/83 15mm Stud Holes

LN 60, 65, YN 60, 62, 65, 67 8/83 - 3/89

RN 105, LN 106, YN 106 8/88 - 7/97 F 151 Vented 302 49 20 19 100 6
LN, YN 61 4 Runner 8/85 - 3/89 F 780 Vented 289 64.5 20 18 100 6
RN 61 4 Runner 1988 - 91
LN, YN, VZN 130 4 Runner 8/89 - 91
LN 107, 111, 125, 135, 172 8/88 - 04
RN 106, 110, 125, 135 8/88 - 04
LN 165, 167, 170, 172 8/97 - 04
RZN 154, 168, 169, 173, 174 8/97 - 04
LN 192R 3.0Lt Diesel 4WD 8/88 - 04
KZN 165 8/97 - 04
VZN 167 8/88 - 04
LN, RN, VZN, KZN 8/91 - 95 F 775 Vented 291 66 25 23 100 6
KUN 20#, GGN 25#, 08/04 - on F 2714 Vented 297 67 25 23 108 6
LAN 25#, TGN 26#

KLUGER / HIGHLANDER
CV, CVX, Grande - V6 3.3L 8/03 - 07 F 2710 3 Vented 296 50 28 26 62 5
GSU40 FWD V6 4D Wagon 2007 - 2008 F 2734 3 Vented 328 49.5 28 25 62 5
GSU45 4WD V6 4D Wagon 2007 - 2008
GSU40 FWD GRANDE 2007 - 2008
GSU45 4WD GRANDE 2007 - 2008
R 2735 3 Solid 309 69.7 10 8.5 62 5

LITE-ACE
KM 20 RV 4 Door Van 10/79 -10/82 F 755 3 Vented 230 37 18 17 74 4
CM 20, KM 20, YM 21 10/82 - 8/85 F 756 3 Vented 230 44 20 19 74 4
CM 30, 35, KM 36, YM 30, 35 9/85 - 8/88 F 158 3 Vented 255 42 20 19 74 4
YM 40 1986 - 8/88 F 758 3 Vented 260 45 20 19 95 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

194 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

LANDCRUISER, BUNDERA
BJ 40, HJ 45, FJ 40, 55 9/79 - 7/80 F 150 3 Vented 302 49 20 19 100 6
10.5mm Stud Holes
BJ 42 8/80 -10/84 F 151 Vented 302 49 20 19 100 6
BJ 60, 70, 73, 74 11/84 -1/90
15 mm Stud Holes
HJ 47, 60, 61, 75 1980 - 99 F 151 Vented 302 49 20 19 100 6
HZJ 70, 73, 75 15 mm S
tud Holes
PZJ 70, 73, 75
FJ 40, FJ 60, FJ 70 Series 1980 - 92 F 151 Vented 302 49 20 19 100 6
FZJ 75, KZJ70 8/92 - on 15 mm Stud Holes
RJ 70, LJ 70 11/84 - 8/92 F 154 Solid 302 49 12.7 11.5 100 6
FJ HZJ 70, 73, 75, FZJ 75 1990 - on R 787 Vented 312 68 18 16 106 6

LANDCRUISER - FJ CRUISER
all models 2006 - on F 2716 Vented 319 67.5 28 26 108 6
R 793 Vented 312 68 18 16 106 6

LANDCRUISER - 70 SERIES
78 and 79 Series 8/99 - on F 790 Vented 322 65 32 30 115 5
HZJ78, HDJ78, R 794 Vented 312 102.5 18 16 110 5
VDJ76 V8 Turbo Diesel 2/07 - on F 790 Vented 322 65 32 30 115 5
HZJ76 6cyl Turbo Diesel 2/07 - on R 794 Vented 312 102.5 18 16 110 5

LANDCRUISER - 80 SERIES
FJ 80, HDJ 80, HZJ 80 1990 - 8/92 F 782 Vented 286 58 25 23 106 6
Early 80 Series ( Rear ) R 785 Vented 312 103 18 16 106 6
FZJ 80, HDJ 80, HZJ 80 8/92 - 1/98 F 784 Vented 311 58 32 30 105 6
Late 80 Series ( Rear ) R 786 Vented 336 103 18 16 106 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 195
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

LANDCRUISER / PRADO - 90 SERIES

VZJ90, KZJ90, LJ90, RZJ90 7/96 - on F 792 Vented 319 70 22 20 108 6
RV4, RV6, GXL, VX, VT, GRANDE R 793 Vented 312 68 18 16 106 6

LANDCRUISER / PRADO - 120 SERIES

All models 9/02 - 09 F 2700 Vented 338 68 28 26 108 6
R 793 Vented 312 68 18 16 106 6

LANDCRUISER - 100 SERIES

UZJ 100 R : HDJ 100 R 1998 - 2006 F 788 Vented 312 71 32 30 115 5
LEXUS LX 470 V8
6 and 8 Cylinder R 789 Vented 330 103 18 16 110 5
FZJ 105 R : HZJ 105 R 1998 - 2006 F 790 Vented 322 65 32 30 115 5
791
6 Cylinder R Vented 335 103 18 16 110 5
( Fixed front axle version only )

LANDCRUISER - 200 SERIES

4.0L, 4.5L, 4.7L 2008 F 2722 Vented 340 83.6 32 39 112 5
R 2723 Vented 345 76.5 18 16 112 5

PRADO - 90 SERIES
VZJ90, KZJ90, LJ90, RZJ90 7/96 - on F 792 Vented 319 70 22 20 108 6
RV4, RV6, GXL, VX, VT, GRANDE R 793 Vented 312 68 18 16 106 6

PRADO - 120 SERIES

All models 9/02 - 09 F 2700 Vented 338 68 28 26 108 6
R 793 Vented 312 68 18 16 106 6

PRADO - 150 SERIES

All models 11/09 - on F 2736 Vented 338 68.5 32 29 108 6
R 2737 Vented 312 68 18 16 108 6

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

196 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TOYOTA - 4WD / SUV / VAN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

RAV 4
SXA10 4/94 - 5/00 F 690 3 Vented 302 46 18 16 62 5
R 691 3 Solid 303 58 9 8 62 5
ACA20R, ACA22R, ACA23R 5/2000 - 05 F 692 3 Vented 275 49 25 23 62 5
R 693 3 Solid 303 62 9 8 62 5
ACA33R 11/2005 - on F 2744 3 Vented 296 49.5 28 25 62 5
R 2745 3 Solid 281 55 12 10.5 62 5

TARAGO / ESTIMA / PREVIA / SIENNA

YR 20, 21, GL, DLX 11/82 - 8/85 F 157 3 Vented 255
PART NOT AVAILABLE 44.5 20 19 74 4
REFERENCE ONLY
CR 21 DLX
YR 21, 22 8/85 - 1/90 F 158 3 Vented 255 42 20 19 74 4
YR 31 4WD 1986 - 1/90 F 159 3 Vented 260 45 25 24 95 5
TCR 1, TCR 2 5/90 - 2/00 F 760 3 Vented 255 53 25 23 62 5
with rear drums
TCR 1, TCR 2 with ABS 5/90 - 2/00 F 762 3 Vented 271 53 25 23 62 5
TCR 1, TCR 2 5/90 - 2/00 F 761 3 Vented 279 53 22 20 62 5
with rear discs - non ABS
TCR 1, TCR 2 ( Rear ) R 716 3 Vented 291 68.5 18 17 60 5
ACR30 Gli, GLX, Ultima 2/00 - 4/03 F 735 3 3 Vented 276 49.5 28 26 62 5
R 697 3 Solid 291 68.5 12 10.5 62 5
ACR30 Gli, GLX, Ultima 4/03 - 1/06 F 2705 3 3 Vented 296 49.3 28 26 62 5
R 697 3 Solid 291 68.5 12 10.5 62 5
ACR50 4DR WAGON 2005 - 2007 F 2730 Vented 296 49.5 28 25 62 5
GCR50 3DR VAN 2007 - 2008
GCR50 4DR WAGON 2007 - 2008
R 2731 Solid 298 64.5 10 8.5 62 5

TOWNACE / SPACIA
YR 2#, 39 1992 - 7/00 F 778 3 Vented 255 42 25 23 74 4

Tercel
4WD 8/82 - 9/90 F 147 3 Solid 243 39.1 11 10 54 4

TUNDRA
4.7L V8 2WD & 4WD 2000 - 05 F 7420 Vented 318 70.5 28 26 108 6
All models 2005 - 08 F 2724 Vented 354 83.5 32 29 112 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 197
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
TRIUMPH C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

1500 TC 1973 - 76 F 173 3

PART NOT AVAILABLE

REFERENCE ONLY Solid 221 37.5 9.5 9 67 4
2000 Mk I 1964 - 70 F 170 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 247.6 32 8.7 7.75 67 4
2000, 2500 Mk II 1969 - 75 F 171 3 Solid 247.6 32 12.7 11.5 67 4
PART NOT AVAILABLE
2500 TC 1973 - 78 REFERENCE ONLY

2.5 Pi 1970 - 75
TR3 late models F 163 3
PART NOT AVAILABLE
Solid 280.7 38.2 12.7 11.4 79 4
REFERENCE ONLY
TR4 early models
TR3A 1963 - 64 F 174 3 Solid 275.4 38 12.7 11.4 79 4
TR4, TR4A 1962 - 67
TR5 10/67 - 69
TR6 1969 - 75
TR7 1978 - 82 F 172 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 240 57 10 9 67 4
Dolomite, Sprint 1975 - 78 F 173 3REFERENCE
PART NOT AVAILABLE
ONLY Solid 221 37.5 9.5 9 67 4
Spitfire - MK I, II, III 1962 - 80 F 2170 3 Solid 232 26.3 9.6 8.3 66.7 4
Herald - 12/50 1963 - 71 PART NOT AVAILABLE
REFERENCE ONLY
1200 1962 - 71
13/60 1967 - 71

198 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

BEETLE (check production codes e.g. IJ-Y.... and ILS - these are found inside the vehicles service book)
From 1C-X-400 001 1ZM 2000 - on F 801 3 Vented 280 36.7 22 19 65 5
From 1C-X-400 001 1ZP
FROM 1C-X-400 001 F 802 3 Vented 288 34 25 23 65 5
1ZH, 1ZE, 1ZD
Rear fits all models above R 803 3 Solid 232 39.5 9 7 65 5
From 1C-X-400 001 1LJ 2000 F 838 3 3 Vented 312 34.2 25 23 65 5
‘RSI’ Only (V Limited)
R 800 3 Vented 256 36.7 22 19 65 5

BORA
FR. WHEEL DR (14in RIM) 1LQ 1998 - on F 800 3 Vented 256 36.7 22 19 65 5
FR. WHEEL DR (15in RIM) 1998 - on F 806 3 Vented 280 46.2 22 20 68 5
1KT (up to 1J-YP061677) 1998 - on F 806 3 Vented 280 46.2 22 20 68 5
1KT (up to 1J-YW238680) 1998 - on R 803 3 Solid 232 39.5 9 7 65 5
Fr Wheel Dr 1998 - on F 833 3 Vented 288 28 25 23 65 5
1LN, 1LE, 1ZH, 1ZE, 1ZD
V6 4MOTION 1ZQ, 1LJ 1998 - on F 838 3 3 Vented 312 34.2 25 23 65 5
V6 4WD 16in Rim 1KU, 2EE 1998 - on R 800 3 Vented 256 36.7 22 19 65 5

CADDY III
All Models 2004 - on F 2812 Vented 280 49 22 19 65 5
1.9TDi, 2.0D, 2.0TD F 2810 Vented 288 49.7 25 22 65 5
**Check Dimensions** R 2811 Solid 255 51.5 10 8 65 5
R 2813 Solid 260 48.5 12 10 65 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 199
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

GOLF MK1
1.1L 4/74 - 7/75 F 240 3 Solid 239 35.2 12 10 65 4
1.5L 8/76 - 7/83
1.6L 8/75 - 9/83
1.6L TD 3/82 - 7/83
1.8L 3/79 - 10/83
1.1L 8/75 - 7/83 F 242 3 Solid 239 39 10 8 65 4
1.3L 8/78 - 7/83
1.5L D 8/78 - 7/80
1.6L D 8/80 - 7/83
1.6L GTI 8/76 - 7/82 F 444 3 Vented 239 38.5 20 10 65 4
1.8L GTI 8/82 - 10/83

GOLF MK2
1.0L w/ ABS 8/83 - 10/91 F 240 3 Solid 226 71.2 10 8 39.8 4
1.3L w/ ABS 8/83 - 7/92
1.6L (51/55kW) 8/83 - 12/92
6L D (Auto) 11/83 - 7/92
1.6L TD 8/83 - 10/91
1.8L inc. ABS (Solid Disc) 8/83 - 10/91
1.8L Syncro 4WD 1985 - 91
1.8L w/ ABS only (Solid) 8/83 - 10/91 R 240 3 Solid 226 71.2 10 8 39.8 4
1.0L wo/ ABS 8/83 - 10/91 F 242 3 Solid 239 39 10 8 65 4
1.3L wo/ ABS 8/83 - 10/91
1.6L (53kW) 8/83 - 10/91
1.6L D 11/83 - 7/92
1.8i GTI 16V (Early) 2/86 - 10/88 F 444 3 Vented 239 38.5 20 10 65 4
1.8L inc. ABS (Vented Disc) 8/83 - 10/91
1.8L GT 11/83 - 7/92
1.8L GTI exc. 16V 11/83 - 7/92
All above models rear disc 8/83 - 10/91 R 832 3 Solid 226 71.2 10 8 39.8 4
1.8i GTI 16V (Late) 10/88 - 91 F 446 3 Vented 256 39 20 18 65 4
R 832 3 Solid 226 71.2 10 8 39.8 4

200 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

GOLF MK3
VR6 MK 3 Up to SW 400 000 1994 - 97 F 835 3 Vented 280 28.2 22 20 65 5
VR6 MK 3 From to SW 400 001 1994 - 97 F 833 3 Vented 288 28 25 23 65 5
All MK 3 models ( Rear ) 1991 - 97 R 834 3 Solid 226 71.2 10 8 39.8 5
GTi - VR6 4/94 - 7/95 F 835 3 Vented 280 28.2 22 20 65 5
R 834 3 Solid 226 71.2 10 8 39.8 5
GTi - VR6 8/95 - 98 F 833 3 Vented 288 28 25 23 65 5
R 834 3 Solid 226 71.2 10 8 39.8 5

GOLF MK4
MK 4 1LQ, 1ZF (14in RIM) 1998 - 04 F 800 3 Vented 256 36.7 22 19 65 5
MK 4 1LS, 1ZM (15in RIM) 1998 - 04 F 801 3 Vented 280 36.7 22 19 65 5
1LN, 1LE, 1ZH, 1ZE, 1ZD 1998 - 04 F 802 3 Vented 288 34 25 23 65 5
1ZQ, 1LJ - IV models 1998 - 04 F 838 3 3 Vented 312 34.2 25 23 65 5
All MK 4 models ( Rears ) 1998 - 04 R 803 3 Solid 232 39.5 9 7 65 5

GOLF MK5 & MK6

All Models (exc. GTi & R32) 2003 - on F 2812 Vented 280 49 22 19 65 5
**Check Dimensions** F 2810 Vented 288 49.7 25 22 65 5
R 2811 Solid 255 51.5 10 8 65 5
R 2813 Solid 260 48.5 12 10 65 5
GTi 2.0L 4cyl TURBO 2003 - on F 2806 3 3 Vented 312 49.8 25 22 65 5
R 2807 3 3 Solid 285.6 48.4 11.7 10 65 5
R32 3.2L V6 2004 - 09 F 2808 3 3 Vented 345 49.8 30 27 65 5
R 2009 - on R 2809 3 Vented 310 48.5 22 20 65 5

JETTA
All Models (exc. 2.0i TFSI) 2005 - on F 2812 Vented 280 49 22 19 65 5
**Check Dimensions** F 2810 Vented 288 49.7 25 22 65 5
R 2811 Solid 255 51.5 10 8 65 5
R 2813 Solid 260 48.5 12 10 65 5
2.0i 16V TFSI (147kW) 2005 - on F 2806 3 3 Vented 312 49.8 25 22 65 5
R 2807 3 3 Solid 285.6 48.4 11.7 10 65 5

*Volkswagen revised the dimensions of the rear discs for these models. DBA 2811 was 255mm x 10mm and
is now 253mm x 10mm. DBA 2813 was 260mm x 12mm and is now 256mm x 12mm. These discs will fit the early
vehicles prior to the revision as well as those vehicles after the revision.

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 201
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

PASSAT
1.5, 1.6 1973 - 82 F 240 3 Solid 239 35.2 12 10 65 4
Variant Diesel 1.5 1979 - 82
1.3 Coupe 1973 - 75 F 242 3 Solid 239 39 10 8 65 4
Diesel 1.5 GLD 1979 - 82
4WD 4CYL Only 1994 - 97 F 446 3 Vented 256 39 20 18 65 4
R 832 3 Solid 226 71.2 10 8 39.8 4
VR6 AAA Engine (2WD) 1994 - 97 F 833 3 Vented 288 28 25 23 65 5
R 834 3 Solid 226 49 10 8 39.8 5
ADR 1.8, 4WD 1996 - 01 F 806 3 Vented 280 46.2 22 20 68 5
Prod. Codes 1LZ, 1ZJ R 810 3 Solid 245 63.9 10 8 68 5
IV 16” wheels 2001 - on F 838 3 3 Vented 312 34.2 25 23 65 5
ADR 1LB (up to 3B-X-124107) 1996 - 01 F 836 3 Vented 282 46 25 23 68 5
4WD 1LB/1ZC (up to 3B-X-124107) PART NOT AVAILABLE
REFERENCE ONLY
AEB, ACK 1LB (up to X-124107)
ADR 1ZC (from 3B-X-124107) 1996 - 01 F 833 3 Vented 288 28 25 23 65 5
4WD 1LB/1ZC (from 3B-X-124107)
AEB, ACK 1ZC (from X-124107)
+ all 1LB, 1ZC, 1LE from 3B-Y-000001

Rear fits all models above R 810 3 Solid 245 63.9 10 8 68 5

GP all ATE 1ZC (15in RIM) 2001 - on F 833 3 Vented 288 28 25 23 65 5
4MOTION 1ZC/1LE (15in RIM)
GP all ATE 1LT (16in RIM) 2001 - on F 838 3 3 Vented 312 34.2 25 23 65 5
4MOTION 1LT (16in RIM)
Rear all GP ATE models 2001 - on R 810 3 Solid 245 63.9 10 8 68 5
Rear 4MOTION 1ZC/1LE (16in RIM) 2001 - on R 800 3 Vented 256 36.7 22 19 65 5
W8 4MOTION 1LC (17in RIM) 2001 - on F NOT AVAILABLE 334 32
R 800 3 Vented 256 36.7 22 19 65 5
2.3 V5 / 4Motion, 2.8 V6 4Motion” 11/00 - 05 F 2800 3 3 Vented 312 46.2 25 23 68 5
Turbodiesel 2.5 V6 Tdi / 4Motion
1.6i, 1.6i 16V FSI, 2.0i 16V FSI, 4/05 - on F 2806 3 3 Vented 312 49.8 25 22 65 5
1.9 TDI, 2.0 16V TDI 103/125kW 4/05 - on
2.0i 16V TFSI 8/05 - on
Rear fits all models above R 2807 3 3 Solid 285.6 48.4 11.7 10 65 5
R32, R36 & 2.0L Turbo 2005 - on F 2808 3 3 Vented 345 49.8 30 27 65 5
R 2809 3 Vented 310 48.5 22 20 65 5

POLO
Polo 1995 - ON F 837 3 Vented 239 34 18 16 65 4

202 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN COMMERCIAL C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

TIGUAN
All models 2007 - on F 2806 3 3 Vented 312 49.8 25 22 65 5
R 2807 3 3 Solid 285.6 48.4 11.7 10 65 5

TOUAREG
All models 16” wheels 10/02 - on F 2242 Vented 308 55.6 29.5 25.5 76 5
3.2 V6, 2.5 R5 TDI, 30 V6 R 2243 Vented 314 76 22 18 76 5
All models 17” wheels 10/02 - on F 2244 Vented 330 69 32 30 85 5
R 2245 Vented 330 74 28 26 85 5
All models 18” & 19” wheels 10/02 - on F 42246 Vented 350 69 34 32 85 5
all models (exc. Brembo caliper) R 42245 Vented 330 74 28 26 85 5
all models (w/Brembo caliper) R 2249 Vented 358 73.5 28 26 85 5

VOLKSWAGEN
1300, 1500, 1600 1965 - 75 F 243 3
PART NOT AVAILABLE
Solid 278 63 9.5 8 hub 4
REFERENCE ONLY
1600 L, John929 S, LS 1970 - 77
Kombi 1970 - 7/72 F 245 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 278 82.5 13 11.5 66 5
Kombi 8/72 - 7/79 F 246 Solid 278 86 13 11.5 66 5
PART NOT AVAILABLE
REFERENCE ONLY

Kombi 8/79 - 9/85 F 442 3

PART NOT AVAILABLE

REFERENCE ONLY Solid 278 82.5 13 11.5 hub 5

This symbol denotes that this part number is offered as a DBA 4X4 Survival Series disc, and is available under
its heading ( e.g. S = Slotted, 4000 series = Slotted, XS etc ) and also available as a plain standard finish rotor

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 203
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN COMMERCIAL C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

Transporter / Caravelle
T2, U.S.A Vanagon 2WD 8/85 - 92 F 443 Solid 258 54 16 13 hub 5
Floating Caliper Rear Drum Brakes for these models

14” rims (up to 70-T-199 999) 1LA F 447 3 Solid 260 64.5 16 13 68 5
T4 1.8L, T4 2.0L / Diesel 1.9L 9/90 - 96 Girling Rear Drum Brakes for these models

15” rims (up to 70-T-199 999) ILP F 448 3 Solid 282 64.5 18 15 68 5
T4 2.0L / Diesel 1.9L 9/92 - 96 Girling Rear Drum Brakes for these models

Syncro 4WD, Euro Van 2.4L 9/92 - 96

15” rims (up to 70-T-199 999) 449 3 Vented 280 64.5 24 20 68 5
ILE F
T4 2.5L / Diesel 2.4L 9/90 - 6/96 Girling Rear Drum Brakes for these models

Syncro 4WD, Euro Van 2.4L 11/92 - 6/96

15” rims (from 70-T-200001 ILP F 830 3 Solid 282 55 18 15 68 5
T4 Caravelle / Multivan 6/96 - 03 Lucas Rear Disc Brakes DBA-831

15” rims (from 70-T-200000) ILE, ILU F 548 3 Vented 280 54 24 20 68 5

T4 2.5L TDi 111kW 6/96 - 03 Lucas, ITT Rear Disc Brakes DBA-831

Transporter, Multivan, Caravelle Square or Curved Pads

all rear disc brake models 6/96 - 03 R 831 3 Solid 280 40 12 10 68 5
(check production codes e.g.70-T-199.... and ILE - these are found inside the vehicles service book)

204 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLKSWAGEN COMMERCIAL C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

T5 - TRANSPORTER + MULTIVAN
T5 - 16” wheels 04/03 - on F 2242 3 3 Vented 308 55.6 29.5 25.5 76 5
T5 - 17” wheels 04/03 - on F 2248 Vented 333 55.6 33 28.5 76 5
T5 4motion - 16” wheels 07/04 - on F 2242 3 3 Vented 308 55.6 29.5 25.5 76 5
T5 4motion - 17” wheels 07/04 - on F 2248 Vented 333 55.6 33 28.5 76 5
T5 - Rear All Models 04/03 - on R 2247 3 3 Vented 294 44.4 22 19.5 76 5

LT (II)
28 05/96 - 01 F 566 3 Vented 276 77 22 19.5 85 5
R 2267 Solid 258 96.5 12 10 85 5
35 05/96 - 01 F 566 3 Vented 276 77 22 19.5 85 5
R 567 Solid 272 97 16 14 85 5
46 05/96 - 01 F 566 3 Vented 276 77 22 19.5 85 5
R 2268 Solid 285 93 22 19 120 6

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 205
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLVO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

140 / 160 SERIES

142, 144, 145, 164, P1800 1968 - 75 F 384 3 Solid 272 69 12.7 11.4 68 5
ATE Brakes
R 680 3 Solid 295 88.3 9.6 8.6 68 5

164 1968 - 75 F 681 3 Solid 272 70.5 14.3 13.1 68 5
Girling Brakes
R 680 3 Solid 295 88.3 9.6 8.6 68 5

240 / 260 SERIES

240, 260 Series 1974 - 93 F 380 3 Solid 263 65 14.5 13.1 68 5
240, 260 Series 1975 - 93 F 382 3 Vented 263 64.3 24 22.8 68 5
DB 62 Pads
ATE Calipers
240, 260 Series 1976 - 93 F 383 3 Vented 263 67.5 22 20.4 68 5
DB 549 Pads
Girling Calipers
1974 - 93 R 381 3 Solid 281 73.5 9.6 8.4 68 5

360 SERIES
GLE, GLT Hatch 1984 - 91 F 687 3 Solid 239 29 12.7 11.4 68 4

740 SERIES
GLE 14 inch Wheel 1984 - 88 F 684 3 Girling Brakes 262.5 56 22 20 hub 5
GLE 15 inch Wheel/Turbo Hub Seal No.
Non ABS 1329820-3
GLE 14 inch Wheel 1984 - 88 F 683 3 Bendix Brakes 287 56 22 20 hub 5
GLE 15 inch Wheel/Turbo Hub Seal No.
1 329820-3
GLE 14 inch Wheel 1988 - 92 F 685 3 Vented 262.5 56 22 20 68 5
GLE 15 inch Wheel/Turbo 1980 - 1/92 F 686 3 Vented 287 56 22 20 68 5
GLE with ABS 1991 - on F 688* 3 Vented 280 56 26 24 68 5
All Rears Not Multilink 1984 - 1/92 R 381 3 Solid 281 73.5 9.6 8.4 68 5
With Multilink 1984 - 1/92 R 689 3 Solid 265 26 10 8 68 5

SPECIAL NOTE: *
 Easy Identification: DBA 688 Late Model Vehicles with ABS
“ JUMBO “ This particular disc has the single piston caliper fitted to it.

206 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLVO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

760 SERIES
GLE V6 2/83 - 1/84 F 682 3 Vented 287 52 22 20 hub 5
Bendix Brakes
Hub Seal No.1329820-3
(can use DBA 683)
GLE V6, 4 Cyl. Turbo 1984 - 88 F 683 3 Vented 287 56 22 20 hub 5
PART NOT AVAILABLE
Bendix Brakes REFERENCE ONLY
Hub Seal No. 1329820-3
GLE V6 1988 - 90 F 686 3 Vented 287 56 22 20 68 5
GLE with ABS 1991 - on F 688* 3 Vented 280 56 26 24 68 5
Without Multilink 1983 - 87 R 381 3 Solid 281 73.5 9.6 8.4 68 5
With Multilink 1988 - on R 689 3 Solid 265 26 10 8 68 5

850 SERIES
GLE / GLT 4 Stud Wheel 1993 only F 880 3 Vented 280 50.5 26 23 68 4
R 881 3 Solid 295 72 9.6 8.4 68 4
GLE / GLT 5 Stud Wheel 1994 - on F 882 3 3 Vented 280 50.5 26 23 68 5
5 lug - USA 1993 - 97
R 883 3 Solid 295 72.5 10 8.4 68 5

940 SERIES
940 GL/GLE with ABS 1990 - on F 688 3 Vented 280 56 26 24 68 5
940 GL, GLE, SE, Turbo R 381 3 Solid 281 73.5 9.6 8.4 68 5
Not Multilink

960 SERIES
960 1994 - 96 F 688 3 Vented 280 56 26 24 68 5
R 381 3 Solid 281 73.5 9.6 8.4 68 5
960 With Multilink (Sedan Only) 1991 - 94 R 689 3 Solid 265 26 10 8 68 5

C70 coupe / cabriolet

C70 15” Wheels 3/97 - 09/02 F 882 3 3 Vented 280 50.5 26 23 68 5
C70 Rear 2WD 3/97 - 9/02 R 883 3 Solid 295 72.5 10 8.4 68 5
C70 Rear 4WD 3/97 - 9/02 R 884 3
PART NOT AVAILABLE

REFERENCE ONLY Solid 283 62 10 8 68 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 207
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLVO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

s40
S40 all models 7/95 - 6/97 F 885 3 Vented 256 46 24 21.5 69 4
S40 all models 7/97 - 12/03 F 886 3 Vented 281 46 24 21.5 69 4
S40 Rear - all models 7/95 - 12/03 R 887 3 Solid 260 41 10 8.4 90 4

s40 II
S40 II 15” wheels 01/04 - on F 2118 3 Vented 278 48.5 25 23 64 5
S40 II 16” wheels 01/04 - on F 2380 3 Vented 300 48.5 25 23 64 5

s60
S60 15” wheels 11/00 - on F 2382 3 Vented 286 50.3 26 23 68 5
S60 16” wheels 11/00 - on F 2384 3 Vented 305 50.3 28 25 68 5
S60 Rear 15” & 16” wheels 11/00 - on R 2383 3 Solid 288 65 12 10 68 5

s70
S70 15” wheels 1/97 - 11/00 F 882 3 3 Vented 280 50.5 26 23 68 5
S70 Rear 2WD 1/97 - 11/00 R 883 3 Solid 295 72.5 10 8.4 68 5
S70 Rear 4WD 1/97 - 11/00 R 884 3 Solid 283 62 10 8 68 5

s80
S80 15” wheels 5/98 - on F 2382 3 Vented 286 50.3 26 23 68 5
S80 16” wheels 5/98 - on F 2384 3 Vented 305 50.3 28 25 68 5
S80 Rear 15” & 16” wheels 5/98 - on R 2383 3 Solid 288 65 12 10 68 5

s90
S90 All models 1/97 - 05/98 F 882 3 3 Vented 280 50.5 26 23 68 5

v40
V40 all models 7/95 - 6/97 F 885 3 Vented 256 46 24 21.5 69 4
V40 all models 7/97 - 12/03 F 886 3 Vented 281 46 24 21.5 69 4
V40 Rear - all models 7/95 - 12/03 R 887 3 Solid 260 41 10 8.4 90 4

V50
V50 15” wheels 04/04 - on F 2118 3 Vented 278 48.5 25 23 64 5
V50 16” wheels 04/04 - on F 2380 3 Vented 300 48.5 25 23 64 5

v70
V70 15” wheels 1/97 - 05/00 F 882 3 3 Vented 280 50.5 26 23 68 5
V70 Rear 2WD 1/97 - 05/00 R 883 3 Solid 295 72.5 10 8.4 68 5
V70 Rear 4WD 1/97 - 05/00 R 884 3 Solid 283 62 10 8 68 5

208 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd.
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
VOLVO C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

V70 II
V70 II 15” wheels 3
03/00 - on F 2382 Vented 286 50.3 26 23 68 5
V70 II 16” wheels 03/00 - on F 2384 3 Vented 305 50.3 28 25 68 5
V70 II Rear 15” & 16” wheels 03/00 - on R 2383 3 Solid 288 65 12 10 68 5

v90
V90 All models 1/97 - 05/98 F 882 3 3 Vented 280 50.5 26 23 68 5

XC70 Cross Country
XC70 15” wheels 3
03/00 - on F 2382 Vented 286 50.3 26 23 68 5
XC70 16” wheels 03/00 - on F 2384 3 Vented 305 50.3 28 25 68 5
XC70 Rear 15” & 16” wheels 03/00 - on R 2383 3 Solid 288 65 12 10 68 5

XC90 Cross Country

XC90 16” wheels 10/02 - on F 2378 Vented 316 50.4 28 25 68 5
XC90 17” wheels 10/02 - on F 2376 Vented 336 51.3 30 27 68 5
XC90 Rear all models 10/02 - on R 2377 Solid 308 65 20 18 68 5

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 209
 DRUM BRAKES
catalogue - 2010/11
V040810

CONTENTS
Vehicle Make Page # Vehicle Make Page #

BMW 206 leyland 214

chrysler 206 Mazda 215

DAEWOO 207 mazda commercial 215

Daihatsu 207 Mitsubishi 215

Daihatsu Commercial 207 Mitsubishi Commercial 216

FORD 208 Nissan 217

FOrd Commercial 209 Nissan commercial 218

Holden 211 Porsche 219

Holden commercial 212 rOVER 219

Honda 212 suzuki 219

hyundai 213 TOYOTA 220

jeep 213 toyota commercial 221

Kia 214

landrover 214
DRUM BRAKES
BMW
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

1502 1975 - 77 R 1800 E1462 230 47 58 59 231 4

1600, 1602 E10 1967 - 73 Shoes
1802, 1802T E10 1971 - 75
2002 Cabrio, Ti, E10 1969 - 75
2002 Touring, Tii 1969 - 75
1800 E10 1963 - 67 R 1801 E1461 250 47 58 63.5 251 4
2000 E10 1966 - 69 Shoes
2002 Turbo E10 1973 - 75
318, 318 i, 320 i E21 1976 - 82
320/4, 320/6 E21 1976 - 82
2800 CS E3 1968 - 71 R 1802 E1461 250 47 75 63.5 251 5
520 i E12 1968 - 71 Shoes
518, 518 i, 520/4 E12 1972 - 79
520/6 E12 1977 - 6/81
316 i, 318 i E30 1982 - 91 R 1803 E1354/1 228.5 57 62 59 229.5 4
316 i, 318 i E36 9/90 - on R 1804 E1354/1 228.5 47 75 59 229.5 5

chrysler
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Valiant VH, VJ, VK, CH, 1972 - 78 R 1720 Large 228.6 54 71.5 73 229.6 5
CJ, CK, CL Centre Hole
E1264 Shoes
Neon 1721 R
200 39 57.5 60.5 201 5
1722 E1756 250 65 72 78 251 5
Voyager R

211
DRUM BRAKES
DAEWOO
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Cielo, Lanos, Espero, Nubria 2/95 - on R 1680 E1710 200 53 57 67 201 4

Daihatsu
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

charade
G100 1/87 - 94 R 1690 E1658 180 36 Hub 72.5 181 4
G102 1/90 - 93
G200, G202, G203 1/89 - on
G102 1/90 - 93 R 1691 E1682 200 41 56 56.5 201 4

mira
L200, L201 1990 - on R 1692 E1688 228 60 67 69 230.6 5

move
L601 1997 - on R 1692 228 60 67 69 230.6 5

Terios
5 DR Sedan 1997 - on R 1693 E1747 228.6 53.5 66.5 69 230 5

Daihatsu Commercial
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

rocky
Turbo & Non Turbo 1984 - on R 1694 E1607 254 52 107 66 255 5

ferosa
F300, F301 1988 - on R 1694 E1607 254 52 107 66 255 5

212 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
FORD
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Corsair
UA 1989 - 92 R 1700 E1656 228.6 54 68 67 229.5 4

Falcon
XB, XC, XD, XE, XF 10/75 - 86 R 1610 E1271 10” 223/16” 23/4” 211/16” 10.060” 5
Shoes or or or or or
254 55 70 68.5 255.5

Fairlane
Fairlane ZG, ZH, ZJ 10/75 - 81 R 1610 E1271 10” 223/16” 23/4” 211/16” 10.060” 5
Shoes or or or or or
254 55 70 68.5 255.5

Laser
KA, KB 1981 - 85 R 1611 E1394 180 36 hub 55 181 4

KC, KE } Not Wagon 1985 - 91 R 1612 E1604 200 32 Hub 65.5 201 4
KF - KH} “ “
Wagon 1985 - 89 R 1613 E1637 228.6 32.5 Hub 66.5 229.5 4

KF - KH 1991 - on R E1671 200 42 55 58 201 4
KJ, KJ Series II E1685

Meteor
GA. GB 1981 - 85 R 1611 E1394 180 36 HUB 55 181 4

GC, GE 1985 - 89 R 1612 E1604 200 32 HUB 65.5 201 4

Wagon 1985 - 89 R 1613 E1637 228.6 32.5 HUB 66.5 229.5 4

213
DRUM BRAKES
FOrd Commercial
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Bronco
Bronco 1981 - 87 R 1620 E1323 11.020” 23/4” 27/8” 35/8” 11.090” 5
Shoes or or or or or
280 70 73 92 281.6

Courier
1.8, 2.0 1979 - 84 R 1627 E1389 260 50 93 62 261 6
2.0, 2.2, 2.6 1984 - on Shoes

Econovan / maxi / spectron

1800, 2000,2200 1/84 - on R 1625 260 63 93 76 261.5 6
Single Rear Wheel
Except 1800 SWB

F100 / F150 Series

F100 2WD, 4WD 79 - 12/86 R 1620 E1323 11.020” 23/4” 27/8” 35/8” 11.090”
Shoes or or or or or
280 70 73 92 281.6 5
F150 2WD, 4WD 1987 - on R 1630 E1323 280 70 88 92 286.1 5

F250 Series
F250 1974 - 85 R 1621 1621A 9/16” Studs 12” 3” 411/16” 43/4” 12.060” 8
Not semi-floating axle (14mm holes) or or or or or
1621B 5/8” Studs 304.8 76 119 120 306.3
(16mm holes)

E1014

F350 Series
F350 Super Cab 1974 - 79 R 1622 * Rare * 12” 35/8” 53/8” 5” 12.060” 8
F350 2WD (SRW) 1980 - 85 * Model * or or or or or
304.8 92 136.5 127 306.3
F350 2WD (DRW) 10/71 - 83 R 1628B 1628B 5
/8” Studs 12” 3 /16” 55/16” 77/32” 12.090” 8
9

PART NOT
E1018 or or or or or AVAILABLE
REFERENCE ONLY
304.8 90 135 180 307
F350 4WD (DRW) 80 - 89 R 1628B R1018 304.8 90 135 180 307 8
PART NOT AVAILABLE
REFERENCE ONLY

Maverick
GY, KY 1988 - 93 R 1709 E1668 295 72 111 85 296.5 6
Shoes

214 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
FOrd Commercial
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

raider
Raider 2.6L 4WD 1987 - 10/98 R 1625 E1665 260 63 93 76 261.5 6

raNGER
4X2, 4X4 - 3.0L models 2007- on R 1642 295 67 93 80.8 296.5 6

transit
80-100-115-120 8/91 - on R 1640 E1738 254 57.5 132 96 255.5 5
100-115-120-130-150-190 8/91 - on R 1641 E1737 280 75.5 142.5 132.5 281.5 6

215
DRUM BRAKES
Holden
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Apollo
JM 3/93 - on R 1603 E1747 228.6 56 62 71 230 5

astra
TR 9/96 - on R 1680 N1710 200 53 57 67 201 4

Barina
MF, MH 1/89 - 94 R 1608 E1616 180 36 HUB 74 181 4

SB without ABS 1994 - on R 1609 E1705 200 35 HUB 84 201.4 4

commodore
VB, VC, VH, 1978 - 88 R 1605 E1385 9.055” 25/16” 23/4” 215/16” 9.115” 5
VK, VL, 6 cyl., 8 cyl. Shoes or or or or or
230 58 69 74.5 231.5
VC, VH, 4 cyl. 1980 - 83 R 1606 E1385 9.055” 25/16” 23/4” 215/16” 9.115” 5
Shoes or or or or or
230 58 69 74.5 231.5

Early series - HQ
HQ, HJ 1971 - 76 R 1604 E1337 10” 2” 213/16” 23/4” 10.060” 5
HX, HZ 1976 - 80 Shoes or or or or or
WB Utility, Panel Van 1980 - 84 254 50.8 71.5 69 255.5

Gemini
TX, TC, TD 3/75 - 4/78 R 1600 E1174 9” 21/8” 21/8” 25/8” 9.060” 4
Shoes or or or or or
228.6 54 54 67 230.1
RB FWD 5/85 - 87 R 1601 E1601 180 42 HUB 65.5 182 4

Nova
TX, TC, TD 3/75 - 4/78 R 1600 E1174 228.6 54 54 67 230.1 4
LE, LF, LG 1989 - on R 1602 E1379 200 55 54 65.5 201.4 4
E1490

torana
LC 6 cyl. 1969 - 72 F 1607 No Longer 9” 21/8” 213/32” 35/32” 9.060” 5
LH 4, 6 cyl. 1974 - 76 U/A Available in or or or or or
LH 4, 6 cyl. 1974 - 76 Australia 228.6 54 61 80 230.1

216 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
Holden commercial
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E
combo
SB Van 2/1996 - on R 1650 E1732 230 59.5 57 75.5 231.2 4

FronterA
UT 2.0 Litre 3/1995 - on R 1651 E1662 254 61.5 95 75 255.5 6

jackAroo
UBS 13, 52, 16, 521, 11/81 - 91 R 1652 E1595 254 61 96.5 71 255.5 6
522, 17, 55 E1662

rodeo
All models 2WD 1980 - on R 1652 E1402 254 61 96.5 71 255.5 6
All models 4WD 80 - 11/96 E1595
4WD 11/96 - 02 R 1653 T.B.A. 295 61 97 80 296.5 6
All models up to 11/02 R 1654 254 62.5 101 71 255.5 6
EXCEPT 4WD Hi-Ride Susp.
V6 4WD Hi-Ride Susp. 2002 - on R 1655 295 59 101 80.6 296.5 6

shuttle
WFR 1982 - 90 R 1652 E1402 254 61 96.5 71 255.5 6
E1413

Honda
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Accord
SJ 1977 - 12/81 R 1823 E1352 180 44.5 hub 60.5 181 4
E1397
SY, AD 1982 - 12/85 R 1824 E1613 200 42.5 hub 72 201 4

CA 1/86 - 89 R 1825 E1614 200 42.5 61 59 201 4

Civic
SB, SC, SE, SF 1973 - 79 R 1820 E1352 180 43 hub 72 181 4
E1397
SL, WC 1980 - 83 R 1821 E1393 180 34 hub 51 181 4

AL, ED 1984 - 91 R 1822 E1610 180 37 61 62 181 4
EG, EH, EK All models 1990 - 96

217
DRUM BRAKES
hyundai
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E
Excel
HA3 8/89 - 7/92 R 1670 E1679 180 46.5 hub 71.5 181 4

8/92 - 5/96 R 1671 E1701 180 46.5 hub 71.5 181 4

6/96 - on R 1672 180 42 hub 70 182 4

Excel X3 1.5L 6/96 - on R 1677 180 53.25 76 58.4 182 4

lantra
KF2, KF3 5/1991 - on R 1673 E1702 203 47 HUB 71.5 204 4
E1703

S / Coupe
S / Coupe 5/90 - 7/92 R 1670 E1679 180 46.5 HUB 71.5 181 4

7/92 - on R 1671 E1695 180 46.5 HUB 71.5 181 4
E1701

SANTA FE / TRAGET
V6 DOHC 9/2000 - on R 1676 253.7 69.5 76 78.5 256 5

sonata
AF2, AF3 1988 - 94 R 1674 E1675 225 55 90 72 226.5 4
1994 - 97 R 1675 228.6 55 90 63 230 4

jeep
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

CJ Series 1976 - 78 R 1790 E1470 279.4 80 95 281 5

1978 - 86 R 1791 E1471 254 54 112 70 255.5 5
Cherokee 1979 - 91 R 1792 E1529 279.4 65 78 84 281 6
Cherokee 4WD 1994 - on R 1793 E1715 229 77 72 90 230 5
R 1794 E1716 254 75 72 102 255.5 5

218 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
Kia
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E
Mentor 1993 - on R 1660 E1753 200 42 57 58 201 4
Sportage 1995 - on R 1661 E1754 250 68 43 81 251.4 5

landrover
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Defender
110 Series, 130 Series 1990 - on R 1751 279.4 68 114 88 281 5

Landrover
109 Series 2.5L 1971 - 85 F & R 1751 E1420 279.4 68 114 88 281 5
E1092
109 Series 2.6L 1968 - 81 R 1750 279.4 68 114 88 281 5
– 14.5mm Stud Holes
109 Series 2.6L, 3.5 V8 1971 - 85 R 1751 279.4 68 114 88 281 5
110 Series 2.25, 2.5, 3.5 L 1970 - 90

leyland
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Mini Van 1964 - 79 F 1810 E1332 177.8 47.5 74 60 179.3 4

Mini Moke R E1333
Cooper 1962 - 65 R 1810 E1332 177.8 47.5 74 60 179.3 4
Copper S, Clubman GT 1965 - 71 R 1811 E1332 177.8 47.5 74 83 179.3 4
E1333

219
DRUM BRAKES
Mazda
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E
323 FWD 1.5, 1.3 1981 - 85 R 1611 E1394 180 36 hub 55 181 4
BD 103, 51, EM 355 Shoes
323 FWD 1985 - 89 R 1612 E1604 200 32 hub 65.5 201.4 4

323 FWD Wagon 1985 - 89 R 1613 1637 228.6 32.5 hub 66.5 229.5 4

626 RWD 1978 - 82 R 1614 E1348 228.5 50 no 62 229.6 4
929 1978 - 80 E1408 hole

mazda commercial
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

E1600, E1800 1983 - 11/86 R 1625 E1587 260 63 93 76 261.5 6

Single Rear Wheel
E2000, E2200 Except Wagon
B2000, B2200, B2600
B1800, B2000 1982 - 84 R 1627 E1389 260 50 93 62 261 6
E1411

Mitsubishi
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Sigma GE, GH, GJ, GK, GN 1978 - 87 R 1700 E1384 228.6 54 68 67 230 4
E1384i
Sigma GE, GH, GJ, GK, GN 1978 - 87 R 1700A E1384 229 51 68 62.5 230 4
With Jap Diff E1384i
Lancer CA, CB 1988 - 93 R 1725 E1677 180 39 hub 71.5 181 4
E1681
Lancer CC 10/92 - on R 1726 E1699 203 42 64 64.5 204.2 4
Lancer CC, CE 10/92 - on R 1727 E1681 180 46 64 66 181 4
Mirage CE 1500, 1800
Pajero IO Series 1999 - on R 1728 229 38.5 90 59.5 230.6 5

220 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
Mitsubishi Commercial
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

L200
Petrol 1980 - 85 R 1780 E1444 241 58 93.5 80.5 242.7 6
Diesel 1982 - 85 R 1781 E1594 254 62 93.5 83 255.4 6

L300
SB, SC, SD, SE 1982 - 9/86 R 1781 E1594 254 62 93.5 83 255.4 6
All Models AWD 1983 - on E1593
SF, SG, SH 10/86 - on R 1782 E1594 254 62 75 70.5 255.4 5
WA 2.0 Litre 1994 - on -
SA 1980 - 82 R 1783 PART NOT AVAILABLE
REFERENCE ONLY

WA 2.4 Litre 1994 - on R 1784

WA 2.4 Litre V6 1994 - on R 1785

Pajero
NA, NB, NC, ND, NE, NF, NG 1/83 - 5/91 R 1781 E1594 254 62 93.5 83 255.4 6
NH 1991 - on R 1786 254 62 83 93.5 256 6
10 Series 1999 - on R 1728 229 38.5 90 59.5 230.6 5

Triton
ME, MF, MG, MH, MJ, 2wd 10/86 - 12/96 R 1781 E1594 254 62 93.5 83 255.4 6
ME, MF, MG, MH, MJ 4WD
MK 4wd 1997 - on

221
DRUM BRAKES
Nissan
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

1600
510 Sedan + Wagon 1968 - 73 R 1700 E1339 228.6 54 68 67 230 4
510 Sedan + Wagon 1968 - 73 R 1700A E1339 229 51 68 62.5 230 4
With Jap Diff

180b
610 Sedan + Wagon 1972 - 77 R 1700 E1339 228.6 54 68 67 230 4
610 Sedan + Wagon 1972 - 77 R 1700A E1339 229 51 68 62.5 230 4
With Jap Diff

200b
810 10/77 - 81 R 1700 E1344 228.6 54 68 67 230 4
E1386
810 With Jap Diff 10/77 - 81 R 1700A E1344 229 51 68 62.5 230 4
E1386

bluebird
910 Sedan + Wagon 1981 - on R 1700 E1384 228.6 54 68 67 230 4
E1384/3
910 Sedan + Wagon 1981 - on R 1700A E1384 229 51 68 62.5 230 4
With Jap Diff E1384/3

Gazelle
S12 1/84 - 4/85 R 1700 E1386 229 54 68 67 230 4

Pintara
U12 11/89 - 10/92 R 1700 E1656 229 54 68 67 229.5 4
N14 10/91 - 9/95 R 1701 E1697 180 37.5 68 57.5 181 4
N15 10/95 - on

Skyline
C120 3/78 - 2/81 R 1700 E1386 229 54 68 67 229.5 4
R30 3/81 - 6/86

Stanza
A10 Coupe, Sedan 1979 - 83 R 1700 E1384 228.6 54 68 67 230 4
E1386
A10 Coupe, Sedan 1981 - on R 1700A E1384 229 51 68 62.5 230 4
With Jap Diff E1386

222 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
Nissan commercial
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

520 / 620 / 720

720 2WD 1979 - 12/82 R 1707 E1075 254 51 90 56 255.5 6
720 4WD 9/79 - 3/83 E1400
720 2WD 1983 - 8/85 R 1708 E1584 254 55 90 69 255.5 6

720 4WD

Navara
D21 2WD 9/85 - 8/89 R 1706 E1584 254 56 101 80.5 255.6 6
E1612
D21 4WD 8/89 - 97 R 1704 295 69 100.5 88.5 297 6
D21 2WD 8/89 - 97 R 1716 E1584 260 63.5 100.5 73 262 6
D22 2WD, 4WD 2/97 - on R 1704 N1726 295 69 100.5 88.5 297 5

Nomad
GC22 Van 1986 - 93 R 1700 228.6 54 68 67 229.5 4

Pathfinder
WD21 (Z24) 8/89 - 7/92 R 1702 E1652 260 63.5 100.5 73 262 6
VG30 7/92 - on
VG33 (R50) 9/95 - on R 1703 295 67.7 100.4 88.5 296.5 6

Patrol
MQ Series 1/81 - 12/87 R 1705 E1404 270 65.5 102 74 271.5 6
E1597
GQ Series Wagon 1988 - on R 1709 E1668 295 75 111 85 296.5 6

urvan
E23 Diesel Some 85 - on R 1708 N1584 254 55 90 69 255.5 6
E23 11/80 - 86 R 1715 E1075 254 52 90 59.5 255.5 6
E1400
E24 3/87 - 93 R 1716 E1584 260 63.5 100.5 73 262 6

ute
XFN, DX, ST 1989 - 91 R 1610 E1271 254 55 70 68.5 255.5 5

223
DRUM BRAKES
Porsche
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

924 1977 - 82 R 1850 230 50.5 AXLE 63.2 232 4

SPLIN

rOVER
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

QUINTET
All Models 1983 - on R 1821 E1393 180 34 HUB 51 181 4

suzuki
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Sierra
SJ40/410/413/SJ 1983 - 86 R 1830 E1539, E1627 228.6 49 57 61 230 5
50 Series1-5
SJ50 Series 6+7 1996 - on R 1831 E1628 220 52 57 63 222 5
SJ 413 Series 8+9

swift
SA310, 413 1985 - 88 R 1832 E1616 180 43 HUB 63 182 4

SF310 / 413 3+5 Door 1989 - 94 R 1833 180 43 HUB 63 182 4

SF413 4 Door / SF 416 1989 - 98 R 1834 200 40 64 56 202 4

vitara
2 Door Series 1, 2, 3 1988 - 97 R 1835 E1691 220 42 50 61 222 5
4 Door Series 1, 2, 3 1988 - 97 R 1836 E1758 254 53 50 66 255.6 5
2 Door Series 4 1991 - 98 R 1837 E1683 220 41 100 61 221.5 5
4 Door Series 4 1991 - 98 R 1838 E1735 254 54 100 66 255.6 5
Grande 1998 - on R 1839 220.6 53.3 100 64.9 222 5

X90
X90 1997 - on R 1837 E1683. 220 41 100 61 221.5 5

224 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
TOYOTA
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

camry
SDV10 4 Cyl. 1992 - on R 1603 E1747 228.6 56 62 71 230 5

Celica
TA22, TA23 1971 - 85 R 1735 E1358 228.6 54 60 71 230.6 4
RA23, RA28 Shoes
RA40 Coupe, Liftback
RA60 Coupe, Liftback
ST162 1986 - 89 R 1602 E1490 200 55 54 65.5 201.4 4

Corolla
KE30, KE35, KE38, KE55, 1974 - 84 R 1735 E1356 228.6 54 60 71 230.6 4
Local Brakes Shoes
KE70V Panel Van 1300
AE 80
KE20, KE25, KE26V 1970 - 84 R 1737 E1189 200 46 60 63 202 4
KE30, KE35, KE36, KE38, Shoes
KE50, KE55
KE70 Sedan, Wagon 1981 - 84
AE71 Sedan, Wagon
AE82 SOHC 1985 - 88 R 1602 E1379 200 55 54 65.5 201.4 4
AE90, 92 SOHC 1989 - 94 R 1602 E1490
AE95 4WD 1988 - 94 R 1665 E1591 200 59 54 70.5 201.4 4

Corona
RT80, RT81 with 1970 - 73 R 1735 E1062 228.6 54 60 71 230.6 4
Drum Front/Rear E1182
RT104 SE, CS Sedan 1973 - 83 R 1735 E1358 228.6 59 60 71 230.6 4
RT118 SE Station Wagon Shoes
XT130, XT131
RT132, RT133 Liftback
ST141 Sedan, Wagon 1983 - 86

Cressida
MX32, MX36 1976 - 84 R 1735 E1358 228.6 54 60 71 230.6 4
MX62 Sedan, Wagon Shoes

paseo
EL54 1995 - on R 1666 180 34.5 HUB 80.5 181.4 4

SPACIA
CR27, KR2 4/92 on R 1735 228.6 54 60 71 230.6 4

225
DRUM BRAKES
TOYOTA
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

STARLET
EP91 1996 - on R 1666 180 34.5 HUB 80.5 181.4 4

T-18
TE72 1800 Liftback 1979 - 83 R 1735 E1358 228.6 54 60 71 230.6 4

toyota commercial
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Dyna
YH81, LH 80 100 Series 1985 - on R 1732 E1371 254 67 67 78 256 5

Hi-Ace
RH11 1967 - 74 F & R 1731 E1025 230 58 67 70 232 5
E1028
RH11 1974 - 75 F & R 1748 E1493 230 73 67 62.5 232 5
E1028
RH11 1975 - 81 R 1732 E1371 254 67 67 78 256 5
RH11, 20, 22, 32, 42
LH20, 30
RH11, LH 11
YH50, 60, 70 Series 1982 - 87
LH50, 60, 70 Series
RH11 1975 - 81 F 1733 E1388 254 64 67 70 256 5
RH11, 20, 22, 32, 42
LH20, 30
YH53, 63, 73 1987 - 89 R 1733 E1405
LH51, 61, 71
YH56, 66 LH 56, 66 1986 - 87 R 1744 E1647 295 66 106 83 297 6
RZH103, 113, 125 1989 - on R 1747 E1678 270 66 67 81 272 5
LH103, 113, 125
SBV LXH12, 22
RCH12, 22 8/1995 - on R 1761 E171A 270 66 69 84 272 6

226 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
TOYOTA commercial - Continued
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Hi-Lux 2WD # = RN31, RN34

RN10 1968 - 72 F & R 1731 E1025 230 58 67 70 232 5
E1028
RN10, 20 1972 - 78 F & R 1732 E1375 254 67 67 78 256 5
E1371
RN30, 31, 40, 41 LN30, 40 1978 - 83 R 1732 E1371
RN5#, LN5#, YN5# 1983 - 89
LN8#, 9#, YN8#, 9# RN85 1988 - 97
RN41, RMSQ SR5 1978 - 83 R 1733 E1396 254 64 67 70 256 5
YN57, SR5 1983 - 89 R 1738 E1396 254 62 67 72 256 5
RN90 1988 - 91
LN14#, 15# 1997 on
RZN14#, RZN154#
RN30, 40 LN 30, 40 1978 - 83 F 1749 E1388 254 57 67 70 256 5

KUN 10#, GGN 15# 8/04 - on R 1756 E1998 254 60 62 73.5 256 5
LAN 15#, TGN 15#

Hi-Lux 4WD / 4 Runner

RN36, 46 LN 36, 46 1979 - 83 R 1739 E1371 254 66 91 78 256 6
YN60, 62, 65, 67 LN65 1983 - 89 R
RN105, LN 106, YN 106 1988 - 97 R 1743 E1660 295 66 91 83 297 6
RN61, LN 61, YN 63 1985 - 89 R 1744 E1647 295 66 106 83 297 6
RN106, 110, 130, 1988 - 97
LN107, 111, 130
YN130, VZN 130
LN16#, LN17#, LN19# 8/97 - 4/05
RZN16#, RZN17#, RZN19#
KUN 20#, GGN 25# 8/04 - on R 1757 E1997 295 67 108 76 297 6
LAN 25#, TGN 26#

227
DRUM BRAKES
TOYOTA COMMERCIAL - Continued
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Landcruiser
BJ40 1979 - 81 F 1730 E1414 295 75 106 81 297 6
R 1740 E1083 290 64 106 84 292 6
BJ42 1980 - 84 R 1730 E1414 295 75 106 81 297 6
BJ70, 73 1984 - 90
FJ40, 45, 55 1969 - 75 F & R 1740 E1083 290 64 106 84 292 6
FJ40, 45, 50 1975 - 80 F 1730 E1414 295 75 106 81 297 6
FJ40, 55 1975 - 80 R 1740 E1083 290 64 106 84 292 6
FJ45 1975 - 84 R 1730 E1414 295 75 106 81 297 6
FJ60, 62 1984 - 90 R
FJ70, 73, 75 1984 - 90 R
HJ45 1979 - 80 F & R
HJ45, 47 1980 - 84 R 1730 E1414 295 75 106 81 297 6
HJ 60, 61 1980 - 90
HJ75 1984 - 90
FJ, FZJ, HDJ80, HZJ80 1990 - on R 1745 295 68 106 81 297 6
FJ, FZJ70, 73, 75 1990 - 92 R 1746 295 75 106 81 297 6
HJ, HZJ70, 75
KZJ, PZJ, 70
HDJ80, HZJ80, FZJ80 8/1992 - on R 1755 295 102 106 109 297 6
(full floating axle)

Lite-Ace
KM20, CM20 1979 - 85 F 1734 E1358 228.6 58 60 75 230.6 4
KM36, YM30, 35CM, 36 1986 - 92 R 1735 E1358 228.6 54 60 71 230.6 4

Prado
KZJ9#, LZJ9#, RZJ9# 1996 on R 1744 E1647 295 66 106 83 297 6

Rav4
SXA10 1741 E1747 254 63 67 74 256 5
4/94 R
SXA1# 4/94 - 8/95 1752 R 228.5 66.25 62 70 230.5 5
ACA20, ACA21, 7/2003 - on R 1753 228.5 58.75 61.75 64 230.5 5
CLA2#, 2CA2#

SPACIA
CR27, KR2 4/92 on R 1735 228.6 54 60 71 230.6 4

228 All rights reserved. © Copyright 1998-2011 Disc Brakes Australia Pty Ltd. Trademarks: All DBA Part References listed in this catalogue are Trademarks of Disc Brakes Australia Pty Ltd..
DRUM BRAKES
TOYOTA COMMERCIAL - Continued
Drum Brake Shoe Dia. Machine Centre Drum Max. Stud
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

Tarago
YR 20, 21, 22, CR 21 1982 - 90 R 1736 E1492 254 61 60 74 256 4
TCR10, 20 1990, 96 R 1742 E1492 254 62.5 60 72 256 5

TERCEL
AL25 4WD 10/82 - 4/88 R 1665 200 59 54 70.5 201.4 4

TOWNACE
CR27, KR2 4/92 on R 1735 228.6 54 60 71 230.6 4
YR22, 39 1736 N1396 254 61 60 74 256 4
SBV KR42, SR40 11/96 - on R 1736 N1396 254 61 60 74 256 4

volkswagen
Dia. Machine Centre Drum Max. Stud
Drum Brake Shoe
Model Years F/R Face Face Hole Height Diam. Holes
No.
A B C D E

SYNCHRO
4WD 2.4L Diesel 89 on R 1744 295 67 106 83 297 6

229
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 001 HOLDEN 253 9.7 3.9 DBA 062 MG 273.4 8.7 4.5
DBA 002 HOLDEN 270 12.7 5.3 DBA 063 MGF 240 22 4.2
DBA 003 HOLDEN 270 15.9 5.8 DBA 064 MGF 240 10 3.2
DBA 004 HOLDEN 256 15.9 6 DBA 065 PART NOT AVAILABLE 280 12.5 5.2
DBA 006 HOLDEN 239 10 3.3 DBA 067A CHEVROLET 325 32 10.5
DBA 007 HOLDEN 227 10 2.9 DBA 067B CHEVROLET 325 32 10.5
DBA 008 HOLDEN 256 12.7 4.8 DBA 068 LEYLAND 273 25.4 12
DBA 009 HOLDEN 215 10 2.5 DBA 069A FORD 330 28 8.7
DBA 010 HOLDEN 256 16 8.8 DBA 069B FORD 330 28 8.7
DBA 011 HOLDEN 235 12.7 3.6 DBA 070 PART NOT AVAILABLE 272 22 7.4
DBA 012 HOLDEN 215 10 2.6 DBA 071 FERRARI 277 20 6
DBA 013 HOLDEN 256 15.6 9 DBA 072 JAGUAR 280 9.75 4.7
DBA 014 HOLDEN 276 25.4 10.3 DBA 073 JAGUAR 287 9.5 5.4
DBA 015 HOLDEN 270 22 10.5 DBA 074 PART NOT AVAILABLE 283 12.5 5.8
DBA 016 HOLDEN 279 10.5 5.1 DBA 075 JAGUAR 262 12.5 4.4
DBA 017 HOLDEN 290 22 10.5 DBA 075B JAGUAR 262 12.5 4.5
DBA 018 HOLDEN 292 15.9 8.4 DBA 076 JAGUAR 285 24 7.5
DBA 019 HOLDEN 327 28 13.2 DBA 077 PART NOT AVAILABLE 295 22.3 6.8
DBA 020 HOLDEN 278 20 4.3 DBA 078 JAGUAR 278 10 4.8
DBA 021 HOLDEN 235 20 4.1 DBA 079 PART NOT AVAILABLE 213 10 2.9
DBA 022 HOLDEN 231 17 3.5 DBA 080 PART NOT AVAILABLE 236 12.5 4.7
DBA 023 HOLDEN 256 24 5.3 DBA 081 MINI COOPER 190 9.5 2.9
DBA 024 HOLDEN 270 10 4.7 DBA 082 PART NOT AVAILABLE 203 7.7 2.5
DBA 025 HOLDEN 270 23 10 DBA 083 MORRIS 214 11 3
DBA 026 HOLDEN 279 10.5 5 DBA 084 MORRIS 248 9.5 3.6
DBA 027 HOLDEN 290 23 11.1 DBA 085 HILLMAN 244 8.8 2.9
DBA 030 HOLDEN 250 18 5.4 DBA 086 LANDROVER 300 24 8.4
DBA 031 PART NOT AVAILABLE 259 12.5 4.4 DBA 087 RANGE ROVER 298 14 7.4
DBA 032 HOLDEN 250 18 4.3 DBA 088 RANGE ROVER 290 12.7 5.9
DBA 033 HOLDEN 257 22 5.2 DBA 089 ROVER 257 14.5 6
DBA 034 HOLDEN 265 12 5 DBA 090 CHEVROLET 317 32.5 17
DBA 035 HOLDEN 289 23 7.4 DBA 091 CHEVROLET 317 32.5 17.2
DBA 036 HOLDEN 279 10.7 5.3 DBA 092 RANGE ROVER 297 25 7.9
DBA 036B HOLDEN 279 10.7 5.5 DBA 093 RANGE ROVER 304 12.6 6.7
DBA 037 HOLDEN 279 10.7 5.2 DBA 094 HUMBER 290 12.75 5.2
DBA 038 PART NOT AVAILABLE 284 24 6.6 DBA 094B AUSTIN 280 12.75 5
DBA 039 HOLDEN 270 10 4.5 DBA 095 INTERNATIONAL 298 30 7.4
DBA 040 HOLDEN 296 28 9.1 DBA 096 JEEP 280 24 6.8
DBA 040B HOLDEN 296 28 9.35 DBA 097 JEEP 285 11 5.1
DBA 041 HOLDEN 286 16 7 DBA 098 JAGUAR 291 28 6.9
DBA 045 HOLDEN 280 20 5.8 DBA 099 JAGUAR 294 10 5
DBA 046 HOLDEN 328 28 9.7 DBA 100 FORD 228 11 2.9
DBA 046B HOLDEN 328 28 9.5 DBA 101 FORD 260 18 4.2
DBA 047 HOLDEN 280 20 6.3 DBA 102 FORD 296 18 0
DBA 048 HOLDEN 330 32 11.2 DBA 103 FORD 287 24 5.9
DBA 049 HOLDEN 315 18 7.7 DBA 104 FORD 272 12.7 5.1
DBA 050 PART NOT AVAILABLE 300 12 5.5 DBA 105 FORD 279 16 6.4
DBA 051 CITROEN 270 7 2.9 DBA 106 FORD 287 24 5.9
DBA 053 CITROEN 178 7 3 DBA 106H FORD 287 24 11
DBA 054 CITROEN 269 9 3.5 DBA 107 FORD 287 24 9.8
DBA 056 CITROEN 260 20 5.2 DBA 108 FORD 286 24 7.2
DBA 057 CITROEN 233 9 3.2 DBA 109 FORD 286 24 6.9
DBA 059 CITROEN 224 7 3 DBA 110B FORD 287 24 9.8
DBA 060 MG 209.8 7.5 2.2 DBA 111A FORD 287 15 6.7
DBA 061 MG 209.8 7.7 3 DBA 111B FORD 287 13 6.1

230
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 112 PART NOT AVAILABLE 240 9.5 2.8 DBA 165 CHRYSLER 257 22 4.6
DBA 113 FORD 245 12.7 3.7 DBA 166 CHRYSLER 270 9 3.9
DBA 114A FORD 273 12.7 5.3 DBA 167 CHRYSLER 280 23 5.8
DBA 114B PART NOT AVAILABLE 273 12.7 5.1 DBA 168 FORD 240 20 4.2
DBA 115 FORD 246 12.5 4.8 DBA 170 PART NOT AVAILABLE 247.6 8.7 3
DBA 116 FORD 237 22.4 4.6 DBA 171 PART NOT AVAILABLE 247.6 12.7 4.1
DBA 117 PART NOT AVAILABLE 219 9.5 2.4 DBA 172 TRIUMPH 240 10 3.3
DBA 118 FORD 247 12.5 4 DBA 173 PART NOT AVAILABLE 221 9.5 2.9
DBA 119 FORD 250 14 4.5 DBA 174 TRIUMPH 275.4 12.7 4.7
DBA 120 FORD 297 30 12.6 DBA 175 CHRYSLER 257 20 4.5
DBA 121 FORD 297 30 9 DBA 176 CHRYSLER 270 9 4
DBA 122 PART NOT AVAILABLE 320 32 16.2 DBA 177 CHRYSLER 282 24 6.4
DBA 123 FORD 300 30 12.3 DBA 178 HONDA 231 17 0
DBA 124 FORD 320 30 16 DBA 179 HONDA 282 25 0
DBA 125 FORD 320 32 16 DBA 180 JEEP 300 32.5 8.6
DBA 126 FORD 270 24 5.7 DBA 181 JEEP 298 22.5 6.5
DBA 127 FORD 270 14.3 5.6 DBA 182 HONDA 239 10 3.4
DBA 128A FORD 320 32 16.4 DBA 183 HONDA 239 10 4.2
DBA 128B FORD 320 32 15.6 DBA 184 HONDA 262 21 5.2
DBA 129 PART NOT AVAILABLE 318 32 10.5 DBA 185 HONDA 282 21 5.8
DBA 130 FORD 287 24 10.5 DBA 186 HONDA 262 21 5.1
DBA 131 FORD 287 25 10 DBA 187 HONDA 242 19 4
DBA 132 FORD 287 25 10.5 DBA 188 HONDA 225 10 3
DBA 133 FORD 299 10.5 5.6 DBA 189 HONDA 231 12 3.3
DBA 134 FORD 287 24 10 DBA 190 HONDA 231 12 3.3
DBA 135 FORD 287 24 10 DBA 191 HONDA 231 12 3.3
DBA 136 FORD 328 28 12 DBA 192 HONDA 239 10 3.1
DBA 137 TOYOTA 241 10 3.8 DBA 193 HONDA 215 11 3
DBA 138 TOYOTA 266 12.7 4.6 DBA 194 PART NOT AVAILABLE 212 10 2.5
DBA 139 TOYOTA 228 10 2.6 DBA 195 HONDA 231 17 3.4
DBA 140 TOYOTA 254 12.7 3.9 DBA 196 HONDA 242 19 4.2
DBA 141 PART NOT AVAILABLE 200 10 2.2 DBA 197 HONDA 231 19 3.8
DBA 142 TOYOTA 218 10 3 DBA 198 PART NOT AVAILABLE 242 10 3.5
DBA 143 TOYOTA 243 10 3.5 DBA 199 HONDA 260 10 3.5
DBA 144 TOYOTA 218 12.7 3.1 DBA 200 HONDA 282 23 6.1
DBA 145 TOYOTA 228 12.7 3.3 DBA 201 PART NOT AVAILABLE 279.4 12.7 5.7
DBA 146 TOYOTA 258 20 4.8 DBA 202 CHRYSLER 282 24 6.8
DBA 147 TOYOTA 243 11.1 3.3 DBA 203 PART NOT AVAILABLE 282 25.4 7
DBA 148 TOYOTA 230 12.7 3.2 DBA 204 PART NOT AVAILBALE 279.4 24 7
DBA 149 TOYOTA 243 22 4.6 DBA 205 MITSUBISHI 256 13 4.1
DBA 150 TOYOTA 302 20 6.3 DBA 206 MITSUBISHI 249 12.9 4.1
DBA 151 TOYOTA 302 20 6 DBA 207 MITSUBISHI 280 10.5 5.1
DBA 152 TOYOTA 266 12.7 4.6 DBA 208 MITSUBISHI 254 24 5.1
DBA 153 TOYOTA 302 12.7 6 DBA 209 PART NOT AVAILABLE 239 10 3.1
DBA 154 TOYOTA 302 12.7 5.9 DBA 210 MITSUBISHI 229 13 3.4
DBA 155 TOYOTA 252 20 4.1 DBA 211 PART NOT AVAILABLE 255 12.5 3.9
DBA 156 TOYOTA 257 25 5.8 DBA 212 MITSUBISHI 247 10 3.5
DBA 157 TOYOTA 255 20 5.4 DBA 213 MITSUBISHI 296 30 7
DBA 158 TOYOTA 255 20 5.5 DBA 214 MITSUBISHI 284 20 5.8
DBA 159 TOYOTA 260 25 6.3 DBA 215 MITSUBISHI 228 13 3.6
DBA 160 FIAT 227 10.8 3.1 DBA 216 MITSUBISHI 314 30
DBA 161 FIAT 251.5 11 5 DBA 217 MITSUBISHI 297 20 6.4
DBA 162 PART NOT AVAILABLE 275 18.5 7 DBA 218 PART NOT AVAILABLE 254 24 4.8
DBA 163 TRIUMPH 275 12.75 5 DBA 219 MITSUBISHI 242 18 3.9
DBA 164 FIAT 257 12 5 DBA 220 MITSUBISHI 255 20 5.7

231
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 221 MITSUBISHI 266 24 7.8 DBA 276 PEUGEOT 246.5 8 2.6
DBA 222 MITSUBISHI 251 10 6.3 DBA 277 PEUGEOT 273 12.5 7.2
DBA 223 MITSUBISHI 276 10 7.7 DBA 278 PEUGEOT 290 10 4.8
DBA 224 MITSUBISHI 275 20 5.5 DBA 279 MERCEDES BENZ 262 22 5.1
DBA 225 MITSUBISHI 232 20 4 DBA 280 MERCEDES BENZ 300 28 7.5
DBA 226 MITSUBISHI 255 20 4.7 DBA 281 MERCEDES BENZ 278 9.1 3.9
DBA 227 MITSUBISHI 243 13 3.5 DBA 282 MERCEDES BENZ 310 28 8
DBA 228 MITSUBISHI 255 20 5.4 DBA 283 MERCEDES BENZ 290 12 5
DBA 229 MITSUBISHI 277 22 6.1 DBA 284 MERCEDES BENZ 320 30 8
DBA 230 MITSUBISHI 258 22 5.3 DBA 285 PART NOT AVAILABLE 300 22 7.1
DBA 231 MITSUBISHI 258 22 5.2 DBA 286 MERCEDES BENZ 288 25 6.3
DBA 232 MITSUBISHI 258 22 6.6 DBA 287 MERCEDES BENZ 278 9 7.5
DBA 233 MITSUBISHI 315 18 8.5 DBA 288 MERCEDES BENZ 300 28 7.5
DBA 234 MITSUBISHI 276 24 6.6 DBA 289 MERCEDES BENZ 290 10 4.6
DBA 234T MITSUBISHI 276 24 6.6 DBA 290 DAIHATSU 208 10 2.4
DBA 236 MITSUBISHI 276 27 6.6 DBA 291 DAIHATSU 234 11 3.4
DBA 237 MITSUBISHI 314 24 7.1 DBA 292 DAIHATSU 277 12.5 4.7
DBA 238 MITSUBISHI 323 10 7.1 DBA 293 DAIHATSU 212 10 2.5
DBA 239 MITSUBISHI 285 22 5.4 DBA 294 DAIHATSU 208 11 2.5
DBA 240 AUDI 239 12 3.4 DBA 295 DAIHATSU 234 18 3.8
DBA 241 AUDI 256 22 5.3 DBA 296 DAIHATSU 234 11 3.4
DBA 242 AUDI 239 10 3.1 DBA 297 PART NOT AVAILABLE 211 10 2.5
DBA 243 PART NOT AVAILABLE 278 9.5 7 DBA 298 PART NOT AVAILABLE 211 16 3.1
DBA 244 AUDI 245 10 3.3 DBA 299 DAIHATSU 285 24 3
DBA 245 VOLKSWAGEN 278 13 6.3 DBA 300 NISSAN 218 10 2.7
DBA 246 PART NOT AVAILABLE 278 13 6.3 DBA 301 NISSAN 239 9.5 3.2
DBA 247 AUDI 257 13 4.6 DBA 302 NISSAN 240 12 3.4
DBA 248 AUDI 291 10.5 4.5 DBA 303 NISSAN 240 12 3.5
DBA 249 PART NOT AVAILABLE 291 10.5 DBA 304 NISSAN 235 10 4.8
DBA 250 MERCEDES BENZ 273 12.7 6.6 DBA 305 NISSAN 239 9.5 3.2
DBA 251 MERCEDES BENZ 279 10 4.4 DBA 306 NISSAN 232 10 3.3
DBA 252 MERCEDES BENZ 273 12.7 5.3 DBA 307 NISSAN 245 10 3.4
DBA 253 MERCEDES BENZ 253 12.7 4.8 DBA 308 NISSAN 232 10 3
DBA 254 MERCEDES BENZ 278 12.7 5 DBA 309 NISSAN 250 12 4
DBA 255 MERCEDES BENZ 278 22 6.2 DBA 310 NISSAN 219 9.6 2.7
DBA 256 MERCEDES BENZ 273 19.1 5.2 DBA 311 NISSAN 250 22 4.1
DBA 257 MERCEDES BENZ 273 22 6 DBA 312 NISSAN 267 22 5.5
DBA 258 MERCEDES BENZ 278 22 6.2 DBA 313 PART NOT AVAILABLE 260 20 5.1
DBA 259 MERCEDES BENZ 286 22 6.6 DBA 314 PART NOT AVAILABLE 212 9.5 2.4
DBA 260 MERCEDES BENZ 262 11 4 DBA 315 NISSAN 253 12.7 4.6
DBA 261 MERCEDES BENZ 258 9 3.3 DBA 316 NISSAN 270 12.5 5.4
DBA 262 MERCEDES BENZ 300 27.5 7.6 DBA 317 NISSAN 250 18 6
DBA 263 MERCEDES BENZ 284 12 5 DBA 318 NISSAN 252 20 4.1
DBA 264 MERCEDES BENZ 284 22 5.8 DBA 319 NISSAN 232 18.2 3
DBA 265 MERCEDES BENZ 284 12 5 DBA 320 NISSAN 271 12.5 5
DBA 266 MERCEDES BENZ 295 22 6.6 DBA 321 PART NOT AVAILABLE 271 12.5 5.1
DBA 267 MERCEDES BENZ 278 9 3.7 DBA 322 NISSAN 250 20 4.2
DBA 268 MERCEDES BENZ 294 24 7.2 DBA 323 NISSAN 250 20 4.3
DBA 269 MERCEDES BENZ 284 22 6 DBA 324 PART NOT AVAILABLE 271 12.7 5.4
DBA 270 PEUGEOT 273 12.5 5.1 DBA 325 PART NOT AVAILABLE 271 12.7 5.1
DBA 271 PEUGEOT 273 12 4.1 DBA 326 NISSAN 244 12.7 4.2
DBA 272 PEUGEOT 273 20 5.3 DBA 327 NISSAN 271 12.5 5.2
DBA 273 PEUGEOT 247 20.5 4 DBA 328 NISSAN 271 12.5 6
DBA 274 PEUGEOT 266 20.5 4.6 DBA 329 NISSAN 294 20 6.7
DBA 275 PEUGEOT 283 22 5.9 DBA 330 MAZDA 250 10 3.6

232
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 331 PART NOT AVAILABLE 230 11 3 DBA 385 SAAB 280 12.7 5.1
DBA 332 MAZDA 244 10 3.2 DBA 386 SAAB 267 9.7 3.7
DBA 333 MAZDA 231 13 5.5 DBA 387 SAAB 269 10.5 4.4
DBA 334 FORD 250 20 4.1 DBA 388 SAAB 280 12.8 5.4
DBA 335 MAZDA 250 18 4 DBA 389 SAAB 280 20 5.7
DBA 336 MAZDA 228 18 7.5 DBA 390 LANCIA 251 12.7 4.3
DBA 337 MAZDA 229 13 5.4 DBA 391 LANCIA 251 10 4
DBA 338 PART NOT AVAILABLE 230 12 4 DBA 392A/B PART NOT AVAILABLE 304 32 9
DBA 339 MAZDA 206 13 5 DBA 393 PART NOT AVAILABLE 299 24 6.5
DBA 340 SUBARU 229 12.5 3.8 DBA 394 PART NOT AVAILABLE 282 20 5.1
DBA 341 SUBARU 226 10 4 DBA 395 PART NOT AVAILABLE 289 20 5.9
DBA 342 SUBARU 229 10 4.2 DBA 396 PORSCHE 282 12.5 5
DBA 343 RENAULT 228 20 3.8 DBA 397 PORSCHE 257 13 5.7
DBA 344 RENAULT 254 12 3.9 DBA 398 PORSCHE 282 20 5.6
DBA 345 RENAULT 227.5 10 3 DBA 399 PART NOT AVAILABLE 289 20 5.6
DBA 346A RENAULT 238.5 20 4 DBA 400 PART NOT AVAILABLE 256 24 5.5
DBA 346B RENAULT 238.5 20 4 DBA 401 PART NOT AVAILABLE 247 18 4
DBA 347 RENAULT 250 9 3.5 DBA 402 MITSUBISHI 276 24 5.9
DBA 348 RENAULT 238 11 3.9 DBA 402B PROTON 276 24 6
DBA 349 RENAULT 252 22 5.5 DBA 403 MITSUBISHI 265 10 3.9
DBA 350 PART NOT AVAILABLE 260 7 2.9 DBA 404 MITSUBISHI 262 10 4.1
DBA 351 RENAULT 238 20.1 4.3 DBA 405 HONDA 282 28 7.2
DBA 352 AUDI 239 9 DBA 406 MITSUBISHI 260 10 3.4
DBA 353 PART NOT AVAILABLE 267 10.9 5.2 DBA 407 PART NOT AVAILABLE 256 24 5
DBA 354 PART NOT AVAILABLE 267 9.4 4.3 DBA 408 MITSUBISHI 235 13 3.6
DBA 355 LOTUS 280 26 6.25 DBA 409 MITSUBISHI 266 24 5.5
DBA 356 ALFA ROMEO 284 22 5.8 DBA 410 MITSUBISHI 260 10 3.5
DBA 357 PART NOT AVAILABLE 272 12.5 5.9 DBA 411 MITSUBISHI 256 24 5.1
DBA 358 ALFA ROMEO 272 12.6 5.8 DBA 411B MITSUBISHI 256 24 5
DBA 359 ALFA ROMEO 251 10 3.6 DBA 412 MITSUBISHI 236 18 4
DBA 360 PART NOT AVAILABLE 286 10 5 DBA 413 MITSUBISHI 235 18 4
DBA 361 PART NOT AVAILABLE 261 11 4.2 DBA 414 PART NOT AVAILABLE 256 24 5.2
DBA 362 ALFA ROMEO 249.5 10 3.1 DBA 415 MITSUBISHI 256 24 4.8
DBA 363 ALFA ROMEO 258 10 2.6 DBA 416 MITSUBISHI 260 10 3.7
DBA 364 ALFA ROMEO 233 9 4.9 DBA 417 MITSUBISHI 294 24 6.6
DBA 365 ALFA ROMEO 250 10 3.2 DBA 419 MITSUBISHI 300 22 6.7
DBA 366 PART NOT AVAILABLE 261 12.7 5 DBA 421 MITSUBISHI 256 24 5
DBA 367 ALFA ROMEO 250 12.6 4.1 DBA 422 MITSUBISHI 258 10.4 4.2
DBA 368 ALFA ROMEO 239 11 3.5 DBA 423 MITSUBISHI 266 18 5
DBA 369 PART NOT AVAILABLE 239 22 4.2 DBA 425 MITSUBISHI 276 24 5.9
DBA 370 BMW 240 10 3.4 DBA 426 MITSUBISHI 258 10.5 4
DBA 371 BMW 272 12.7 5.6 DBA 427 MITSUBISHI 284 20 5.2
DBA 372 BMW 256 12.7 4.8 DBA 429 MITSUBISHI 284 20 5.9
DBA 373 BMW 272 12.7 5 DBA 430 PART NOT AVAILABLE 280 23.5 6.1
DBA 374 BMW 273 9.5 4.1 DBA 431 SAAB 280 25 6.7
DBA 375 BMW 272 22 7 DBA 432 SAAB 258 9 3.2
DBA 376 BMW 255 12.7 4.8 DBA 433 SAAB 284 24 6.6
DBA 377 BMW 280 12.7 5.6 DBA 434 SAAB 260 10 4
DBA 378 PART NOT AVAILABLE 255 22 5.2 DBA 436 SAAB 286 10 5
DBA 379 BMW 280 22 6.4 DBA 437 MITSUBISHI 276 24
DBA 380 VOLVO 263 14.3 5.2 DBA 438 HONDA 260 9 3.4
DBA 381 VOLVO 281 9.6 4.9 DBA 439 MASERATI 282 12.7 5.8
DBA 382 VOLVO 263 24 5.6 DBA 440 AUDI 257 13 3.9
DBA 383 VOLVO 263 22 5.6 DBA 441 AUDI 257 20 4.5
DBA 384 VOLVO 272 12.7 5.2 DBA 442 VOLKSWAGEN 278 13 8.6

233
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 443 VOLKSWAGEN 258 16 7.7 DBA 499 HONDA 282 12

DBA 444 VOLKSWAGEN 239 20 3.7 DBA 500 FORD 287 24 7.6
DBA 445 AUDI 245 10 3.5 DBA 501 FORD 287 10.5 5.3
DBA 446 SEAT 256 20 4.5 DBA 502 FORD 287 28 8.2
DBA 447 VOLKSWAGEN 260 16 5.6 DBA 503 FORD 287 16 5
DBA 448 VOLKSWAGEN 282 18 7.4 DBA 504 FORD 298 28 8.9
DBA 449 VOLKSWAGEN 280 24 6.8 DBA 505 FORD 303 16 7.2
DBA 450 HYUNDAI 242 19 5.2 DBA 506 FORD 329 28 11
DBA 451 HYUNDAI 242 19 4.2 DBA 507A/B FORD 300 28 10
DBA 452 HYUNDAI 257 22 4.9 DBA 508 FORD 278 24 6.3
DBA 453 HYUNDAI 257 22 5 DBA 509 FORD 253 20 4.2
DBA 454 HYUNDAI 263 12 3.9 DBA 510 SUZUKI 290 10 4.6
DBA 455 HYUNDAI 260 12 4.2 DBA 511 SUZUKI 213 11 2.6
DBA 456 HYUNDAI 257 24 4.8 DBA 512 SUZUKI 231 17 3.5
DBA 457 HYUNDAI 257 10 3.8 DBA 513 SUZUKI 290 10 4.4
DBA 458 HYUNDAI 262 10 4.4 DBA 514 SUZUKI 287 17 4.4
DBA 459 HYUNDAI 257 10 2.4 DBA 515 SUZUKI 231 17 3.6
DBA 460 HYUNDAI 276 26 6.5 DBA 516 SUZUKI 250 18.5 4.5
DBA 461 HYUNDAI 262 10 4.8 DBA 517 PART NOT AVAILABLE 240 10 3.5
DBA 463 HYUNDAI 257 24 5.8 DBA 518 SUZUKI 310 22 7
DBA 464 HYUNDAI 276 26 6.4 DBA 519 SUZUKI 235 20 4.1
DBA 465 HYUNDAI 284 10 4.7 DBA 520 SUZUKI 246 20 4.3
DBA 466 HYUNDAI 280 27 7.1 DBA 521 SUZUKI 240 10 3
DBA 467 HYUNDAI 315 20 8.2 DBA 522 SUZUKI 231 17 3.4
DBA 468 HYUNDAI 280 26 6.6 DBA 523 SUZUKI 257 17 4.3
DBA 469 HYUNDAI 258 10 4.1 DBA 524 SUZUKI 287 17 4.3
DBA 470 HONDA 260 23 4.8 DBA 525 MAZDA 235 12 3.5
DBA 471 HONDA 260 10 4.2 DBA 526 LANDROVER 262 14 4.9
DBA 472 HONDA 282 25 6.5 DBA 527 LANDROVER 277 21 5.3
DBA 473 HONDA 240 21 4.3 DBA 528 LANDROVER 297 25 8.2
DBA 474 HONDA 262 21 4.8 DBA 529 FORD 240 12 3.6
DBA 475 HONDA 239 9 3 DBA 530 FORD 235 18 3.7
DBA 476 HONDA 300 28 8.1 DBA 531 FORD 231 9 2.6
DBA 477 HONDA 260 9 3.4 DBA 532 FORD 235 22 4.5
DBA 478 HONDA 282 23 5.8 DBA 533 FORD 257 22 5.2
DBA 479 HONDA 282 9 4.2 DBA 534 FORD 250.5 9 3
DBA 480 HONDA 260 23 5 DBA 535 MAZDA 274 22 5.3
DBA 481 HONDA 260 10 3.6 DBA 536 MAZDA 251 9 3
DBA 482 HONDA 300 25 6.3 DBA 537 MAZDA 258 24 6
DBA 483 HONDA 282 12 4.5 DBA 538 MAZDA 255 20 4.6
DBA 484 HONDA 282 28 6.5 DBA 539 MAZDA 261 10 3.6
DBA 485 HONDA 282 21 5.5 DBA 540 JEEP 305 26 7.7
DBA 486 HONDA 298 28 6.8 DBA 541 JEEP 305 10 5.7
DBA 487 HONDA 303 23 6.5 DBA 542 MINI COOPER 276 22 5.8
DBA 488 HONDA 282 23 6 DBA 543 MINI COOPER 259 10 3.4
DBA 489 HONDA 260 9 3.6 DBA 544 MAZDA 270 22 4.8
DBA 490 PART NOT AVAILABLE 236 10 2 DBA 545 MAZDA 270 22 5.4
DBA 491 DAIHATSU 277 18 4.8 DBA 546 MAZDA 276 10 3.7
DBA 492 DAIHATSU 211 10 3.3 DBA 547 MITSUBISHI 260 10 3.4
DBA 493 DAIHATSU 179 10 1.8 DBA 548 VOLKSWAGEN 280 24 6.8
DBA 494 DAIHATSU 236 10 2.9 DBA 549 LANDROVER 298 14 6.8
DBA 495 DAIHATSU 234 16 3.3 DBA 550 MERCEDES BENZ 303 26 7.5
DBA 496 DAIHATSU 273 16 5.49 DBA 551 MERCEDES BENZ 285 15 6
DBA 497 DAIHATSU 250 18 4.4 DBA 552 MERCEDES BENZ 345 32 11.2
DBA 498 DAIHATSU 234 16 3.8 DBA 553 MERCEDES BENZ 331 14 8

234
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 554 SSANYONG MUSSO 278 24 6.4 DBA 617 NISSAN 257 22 6
DBA 555 SSANYONG MUSSO 300 10.5 5.7 DBA 618 NISSAN 260 26 6.5
DBA 556 MERCEDES BENZ 260 12 3.7 DBA 619 NISSAN 232 18 3.5
DBA 557 MERCEDES BENZ 260 22 4.7 DBA 620 NISSAN 250 22 5
DBA 558 MERCEDES BENZ 276 22 5.1 DBA 621 NISSAN 266 22 6
DBA 559 MERCEDES BENZ 258 8 3 DBA 622 NISSAN 315 18 8
DBA 560 TOYOTA 315 32 9 DBA 623 NISSAN 306 26 8.6
DBA 561 PART NOT AVAILABLE 315 16 6.75 DBA 624 NISSAN 277 26 7.5
DBA 562 TOYOTA 275 25 6.2 DBA 625 NISSAN 306 32 10.5
DBA 563 TOYOTA 269 9 3.6 DBA 626 NISSAN 283 28 7
DBA 564 MERCEDES BENZ 276 22 6 DBA 627 NISSAN 250 22 5.5
DBA 565 MERCEDES BENZ 280 10 4.3 DBA 628 NISSAN 250 18 4.5
DBA 566 MERCEDES BENZ 276 22 6.6 DBA 629 NISSAN 300 28 8.6
DBA 567 MERCEDES BENZ 272 16 7 DBA 630 MAZDA 250 18 7
DBA 568 TOYOTA 275 28 7.34 DBA 631 FORD 256 20 4.5
DBA 570 TOYOTA 256 20 5.5 DBA 632A/B FORD 231.5 18 7
DBA 571 PART NOT AVAILABLE 272 10 4.5 DBA 633 MAZDA 264 24 5.5
DBA 572 PART NOT AVAILABLE 256 21 5.5 DBA 634 PART NOT AVAILABLE 258 10 5.5
DBA 573 NISSAN 280 28 7.5 DBA 635 MAZDA 219 13 3
DBA 574 NISSAN 292 16 5.5 DBA 636 MAZDA 276 22 6.5
DBA 576 FORD 258 24 5.8 DBA 637 MAZDA 273 20 5
DBA 577 FORD 258 24 5.3 DBA 638 MAZDA 255 22 7
DBA 578 SUZUKI 287 17 4.1 DBA 639 MAZDA 265 10 4.5
DBA 579 SUZUKI 310 22 6 DBA 640 SUBARU 230 18 4.5
DBA 580 TOYOTA 258 25 5.5 DBA 641 SUBARU 242 18 4.5
DBA 581 PART NOT AVAILABLE 263 16 4 DBA 642 SUBARU 260 24 5.5
DBA 582 TOYOTA 275 30 8 DBA 643 RENAULT 238.5 12 4
DBA 583 TOYOTA 281 22 6 DBA 644 SUBARU 266 10 4.5
DBA 586 TOYOTA 291 16 0 DBA 645 SUBARU 242 18 4
DBA 590 PORSCHE 298 27.5 8 DBA 646 SUBARU 212 10 2.5
DBA 591 PORSCHE 299 24 8 DBA 647 SUBARU 212 9 2
DBA 592A/B PART NOT AVAILABLE 304 32 7 DBA 648 SUBARU 277 24 8
DBA 593 PART NOT AVAILABLE 282 24 6 DBA 649 SUBARU 266 18 6
DBA 594 PART NOT AVAILABLE 304 32 7 DBA 650 SUBARU 294 24 7
DBA 595 PORSCHE 298 28 6.8 DBA 651 PART NOT AVAILABLE 290 10 5
DBA 596 PORSCHE 299 24 6.8 DBA 652 SUBARU 301.1 28 8
DBA 597A/B PART NOT AVAILABLE 282 32 7 DBA 653 SUBARU 290 18 6
DBA 598A/B PART NOT AVAILABLE 282 32 7 DBA 655 SUBARU 316 20 8
DBA 600 NISSAN 258 10 4.5 DBA 656 SUBARU 290 18 5.7
DBA 601 NISSAN 269 10 5 DBA 657 SUBARU 290 10 4.9
DBA 602 HOLDEN 240 18 4.5 DBA 658 PART NOT AVAILABLE 239 12.7 4
DBA 603 NISSAN 240 18 4.5 DBA 659 MAZDA 255 22 6.9
DBA 604 PART NOT AVAILABLE 274 22 7 DBA 660 MITSUBISHI 290 26 6.5
DBA 605 NISSAN 290 10 5 DBA 661 MITSUBISHI 300 22 6.5
DBA 606 NISSAN 235 10 5 DBA 662 MITSUBISHI 245 24 6
DBA 607 NISSAN 290 10 5.5 DBA 663 MITSUBISHI 276 24 6
DBA 608 PART NOT AVAILABLE 274 22 6.5 DBA 664 MITSUBISHI 293 40 12.1
DBA 609 NISSAN 250 12 7 DBA 665 ALFA ROMEO 284 22 6.5
DBA 610 NISSAN 284 10.4 5 DBA 666 ALFA ROMEO 251 10
DBA 611 NISSAN 280 10.5 5.5 DBA 667 ALFA ROMEO 250 9.9 4
DBA 612 NISSAN 250 18 4.5 DBA 668 ALFA ROMEO 268 22 5.5
DBA 613 PART NOT AVAILABLE 250 22 8.5 DBA 669 ALFA ROMEO 258 10 4
DBA 614 FORD 258 10 4 DBA 670 BMW 284 10 5
DBA 615 NISSAN 250 22 8 DBA 671 BMW 258 10 4
DBA 616 NISSAN 260 10.4 4.5 DBA 672 BMW 284 12 6

235
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 673 BMW 272 19 6 DBA 730 TOYOTA 255 22 5.5

DBA 674 BMW 284 10 5 DBA 731 TOYOTA 269 12 4.5
DBA 675 BMW 284 22 6 DBA 732 TOYOTA 255 25 5.5
DBA 676 BMW 280 10 5 DBA 733 TOYOTA 255 28 6
DBA 677 BMW 280 25 7 DBA 734 TOYOTA 288 10 5
DBA 678 BMW 260 12.7 4.5 DBA 735 TOYOTA 276 28 7
DBA 679 BMW 260 22 5 DBA 736 TOYOTA 269 10 4.5
DBA 680 VOLVO 295 9.6 6 DBA 737 TOYOTA 276 28 7
DBA 681 VOLVO 272 14.3 6 DBA 738 TOYOTA 291 16 5
DBA 682 VOLVO 287 22 8 DBA 739 TOYOTA 258 22 5.5
DBA 683 VOLVO 287 22 9.5 DBA 740 TOYOTA 243 22 5
DBA 684 VOLVO 262.5 22 8 DBA 741 TOYOTA 269 10 4.5
DBA 685 VOLVO 262.5 22 5.5 DBA 742 TOYOTA 255 22 5
DBA 686 VOLVO 287 22 6.7 DBA 743 TOYOTA 278 25 7
DBA 687 VOLVO 239 12.7 3.5 DBA 744 TOYOTA 288 10 5
DBA 688 VOLVO 280 26 6.5 DBA 745 TOYOTA 315 28 10
DBA 689 VOLVO 265 10 4 DBA 746 TOYOTA 307 16 5.6
DBA 690 TOYOTA 302 18 5 DBA 747 PART NOT AVAILABLE 275 28 6.5
DBA 691 TOYOTA 303 9 5 DBA 749 TOYOTA 307 12 6
DBA 692 TOYOTA 275 25 6.5 DBA 750 PART NOT AVAILABLE 258 22 5
DBA 693 TOYOTA 303 9 5.2 DBA 751 TOYOTA 258 10 4
DBA 695 TOYOTA 254 18 4 DBA 753 TOYOTA 255 20 4.5
DBA 696 PART NOT AVAILABLE 240 9 4.5 DBA 754 TOYOTA 263 16 4.1
DBA 697 TOYOTA 291 12 0 DBA 755 TOYOTA 230 18 4
DBA 698 TOYOTA 316 34 10.85 DBA 756 TOYOTA 230 20 4.5
DBA 699 TOYOTA 330 18 7.6 DBA 757 TOYOTA 291 9 5
DBA 700 PART NOT AVAILABLE 234 12.5 4 DBA 758 TOYOTA 260 20 5.5
DBA 701 TOYOTA 243 13.5 4.5 DBA 759 TOYOTA 275 25 6.2
DBA 702 TOYOTA 243 18 4 DBA 760 TOYOTA 255 25 5.5
DBA 703 TOYOTA 242 9 3 DBA 761 TOYOTA 279 22 6.5
DBA 704 TOYOTA 238 18 4.5 DBA 762 TOYOTA 271 25 6.5
DBA 705 TOYOTA 250 12.7 3.5 DBA 763 PART NOT AVAILABLE 284 22 6.2
DBA 706 TOYOTA 280 10.5 5 DBA 764 TOYOTA 269 9 4
DBA 707 PART NOT AVAILABLE 269 10 4.5 DBA 766 TOYOTA 255 25 6.5
DBA 708 TOYOTA 258 22 5 DBA 767 TOYOTA 285 28 7.6
DBA 709 HOLDEN 255 22 5 DBA 768 TOYOTA 285 28 7.5
DBA 710 HOLDEN 266 9 3.5 DBA 769 ALFA ROMEO 305 28 7.6
DBA 711 TOYOTA 238 22 5.5 DBA 770 TOYOTA 300 30 10.5
DBA 712 TOYOTA 255 25 5.2 DBA 771 TOYOTA 296 35 12
DBA 713 TOYOTA 269 9 3.7 DBA 772 TOYOTA 258 25 6
DBA 714 TOYOTA 238 18 4 DBA 773 HOLDEN 295 32.5 8
DBA 715 TOYOTA 300 22 8 DBA 774 HOLDEN 317.5 33 9.2
DBA 716 TOYOTA 291 18 6 DBA 775 TOYOTA 291 25 7
DBA 717 TOYOTA 266 18 5 DBA 776 CHRYSLER 302 28 7.7
DBA 719 TOYOTA 324 16 5.7 DBA 777 CHRYSLER 290 12.5 3.7
DBA 720 TOYOTA 248 18 4 DBA 778 TOYOTA 255 25 4.5
DBA 721 TOYOTA 248 22 5 DBA 779 ALFA ROMEO 240 11 3.5
DBA 722 TOYOTA 269 18 5 DBA 780 TOYOTA 289 20 6.5
DBA 723 TOYOTA 235 18 3.7 DBA 781 TOYOTA 248 22 4.5
DBA 724 TOYOTA 266 12.7 5 DBA 782 TOYOTA 286 25 7.5
DBA 725 PART NOT AVAILABLE 261 12.5 0 DBA 783 TOYOTA 254 22 5
DBA 726 DAEWOO 256 24 5.6 DBA 784 TOYOTA 311 31.9 9
DBA 727 PART NOT AVAILABLE 252 20 4 DBA 785 TOYOTA 312 18 7.5
DBA 728 TOYOTA 252 20 4.5 DBA 786 TOYOTA 336 18 8.5
DBA 729 PART NOT AVAILABLE 268 18 5 DBA 787 TOYOTA 312 18 6.5

236
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 788 TOYOTA 312 32 8.5 DBA 845 TOYOTA 315 30 9.5
DBA 789 TOYOTA 330 18 8 DBA 846 TOYOTA 310 16
DBA 790 TOYOTA 322 32 8.5 DBA 847 HOLDEN 260 24 5
DBA 791 TOYOTA 335 18 7.5 DBA 848 GMC 317 32.5 17
DBA 792 TOYOTA 319 22 6.5 DBA 849 HOLDEN 240 10 3.1
DBA 793 TOYOTA 312 18 6 DBA 850 FORD 260 24 5.5
DBA 794 TOYOTA 312 18 7.5 DBA 851 FORD 253 20 4
DBA 795 FORD 330 38 20.8 DBA 852 FORD 276 26 7
DBA 796 FORD 326 30 11.2 DBA 853 FORD 257 14 5
DBA 797 FORD 330 38 20.2 DBA 854 FORD 239.5 20 4
DBA 798 FORD 331 38 13 DBA 855 FORD 276 26 6.75
DBA 799 FORD 326 30 11.3 DBA 856 FORD 267 14 5
DBA 800 AUDI 256 22 6 DBA 857 FORD 256 24 5
DBA 801 AUDI 280 22 6 DBA 859A/B FORD 256 18
DBA 802 AUDI 288 25 7 DBA 860 FORD 286 26 7.5
DBA 803 AUDI 232 9 2.6 DBA 861 FORD 285 12 5.5
DBA 804 AUDI 280 13 5.3 DBA 862 FORD 308 30 12.25
DBA 805 AUDI 288 15 6.6 DBA 863 FORD 334 14 8.6
DBA 806 AUDI 280 22 6.2 DBA 864 PART NOT AVAILABLE 305 26 8.5
DBA 807 AUDI 288 25 7.5 DBA 865 FORD 301 12 8.6
DBA 808 AUDI 245 10 5.5 DBA 866 PART NOT AVAILABLE 296 28 8.5
DBA 809 AUDI 245 10 3.5 DBA 867 EUNOS 286 9.5 4.5
DBA 810 AUDI 245 10 3.5 DBA 868 EUNOS 274 28 7
DBA 811 HOLDEN 250 18 4 DBA 869 EUNOS 286 9.5 4.5
DBA 812 PART NOT AVAILABLE 266 18 5 DBA 870 LADA 239 12 4
DBA 813 BMW 332 30 11.2 DBA 871 FORD 294 24 7.17
DBA 814 BMW 324 12 DBA 872 LADA 272 11 6
DBA 815 HOLDEN 280 25 6.2 DBA 873 KIA 258 24 6
DBA 816 HOLDEN 264 10 3.8 DBA 874 KIA 260 10 4
DBA 817 HOLDEN 256 24 5.8 DBA 875 KIA 240 20 4.5
DBA 818 HOLDEN 240 10 3 DBA 876 KIA 284 24 5.7
DBA 819 HOLDEN 260 10 4 DBA 877 KIA 274 24 6
DBA 820 HOLDEN 236 12 4 DBA 878 KIA 274 26 6.1
DBA 821 HOLDEN 236 20 4 DBA 879 KIA 260 10 3.7
DBA 822 HOLDEN 256 20 4 DBA 880 VOLVO 280 26 5
DBA 823 BMW 356 36 14 DBA 881 VOLVO 295 9.6 5
DBA 824 BMW 324 20 8.1 DBA 882 VOLVO 279 26 6.5
DBA 825 HOLDEN 288 25 6.9 DBA 883 VOLVO 295 9 5
DBA 826 HOLDEN 286 10 5 DBA 884 VOLVO 283 10 4.5
DBA 827 AUSTRALIA POST 254 14.7 5 DBA 885 VOLVO 256 24 5
DBA 828 VOLKSWAGEN 270 24.13 7 DBA 886 VOLVO 281 24 6.4
DBA 829 VOLKSWAGEN 254 24 4 DBA 887 VOLVO 260 10 3.5
DBA 830 VOLKSWAGEN 282 18 7 DBA 888 JEEP 280 24.5 6.9
DBA 831 VOLKSWAGEN 280 12 5 DBA 889 JEEP 288 28 7.5
DBA 832 VOLKSWAGEN 226 10 4.5 DBA 890 DAEWOO 236 12 4
DBA 833 VOLKSWAGEN 288 25 7 DBA 891 DAEWOO 256 24 5.5
DBA 834 VOLKSWAGEN 226 10 4 DBA 892 DAEWOO 256 24 5.1
DBA 835 VOLKSWAGEN 280 22 4.5 DBA 893 DAEWOO 258 10 4.5
DBA 836 VOLKSWAGEN 283 25 7.3 DBA 894 DAEWOO 256 24 5.2
DBA 837 VOLKSWAGEN 239 18 4 DBA 895 DAEWOO 258 10 4.6
DBA 838 AUDI 312 25 8 DBA 896 DAEWOO 235 20 4.5
DBA 840 HOLDEN 280 26 7.5 DBA 897 DAEWOO 236 12.7 3.7
DBA 841 HOLDEN 313 18.1 7 DBA 898 PART NOT AVAILABLE 258 9 3.1
DBA 842 HOLDEN 280 26 7.3 DBA 899 NISSAN 247 18 4
DBA 844 PART NOT AVAILABLE 231 22 4.8 DBA 900 NISSAN 252 20 5

237
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)
DBA 901 NISSAN 257 26 6.5 DBA 960 MAZDA 276 28 8
DBA 902 NISSAN 258 9 3.5 DBA 961 PART NOT AVAILABLE 276 28 8
DBA 903 NISSAN 280 22 7 DBA 962 MAZDA 274 28 7
DBA 904 NISSAN 258 9 3.7 DBA 964 FORD 275 24 6
DBA 905 PART NOT AVAILABLE 266 10 5 DBA 965 FORD 272 22 5.5
DBA 906 NISSAN 258 9 3.5 DBA 966 BMW 300 22 6.7
DBA 907 NISSAN 280 26 8.5 DBA 967 BMW 294 19 6.3
DBA 908 NISSAN 292 18 7 DBA 968 PART NOT AVAILABLE 315 28 9.25
DBA 909 NISSAN 280 30 7 DBA 969 BMW 300 20 6
DBA 910 NISSAN 280 22 7 DBA 970 BMW 282 25 6.5
DBA 911 PART NOT AVAILABLE 278 9.5 6.5 DBA 971 BMW 302 28 8
DBA 912 NISSAN 258 10 4 DBA 972 PART NOT AVAILABLE 300 12 6
DBA 913 NISSAN 257 26 6 DBA 973 BMW 300 20 6
DBA 914 NISSAN 280 26 8 DBA 974 BMW 302 22 7.5
DBA 915 NISSAN 278 9 4 DBA 975 BMW 302 12 6.5
DBA 917 NISSAN 234 7 2.5 DBA 976 BMW 300 10 5
DBA 918 NISSAN 250 18 4.5 DBA 977 PART NOT AVAILABLE 300 10 5
DBA 919 NISSAN 280 22 6.2 DBA 978 BMW 286 12 5.2
DBA 920 NISSAN 234 12 3.5 DBA 979 BMW 286 22 7
DBA 921 NISSAN 240 7 2.5 DBA 980 BMW 276 19 5
DBA 922 NISSAN 280 28 8 DBA 981 BMW 272 10 4.5
DBA 923 NISSAN 292 9 5.5 DBA 982 BMW 272 10 4.7
DBA 924 PART NOT AVAILABLE 274 22 6.6 DBA 983 BMW 280 10 4.5
DBA 925 NISSAN 258 9 3.5 DBA 984 BMW 315 28 9.5
DBA 927 NISSAN 282 20 6.18 DBA 985A/B PART NOT AVAILABLE 312 19.9 6.6
DBA 929 NISSAN 300 22 8 DBA 986 BMW 296 22 7.5
DBA 930 MAZDA 238 18 4 DBA 987 BMW 298 10 5
DBA 931 MAZDA 222 10 4.5 DBA 988 BMW 324 30 10.25
DBA 932 MAZDA 247 10 4.5 DBA 989 PART NOT AVAILABLE 298 20 6
DBA 933 PART NOT AVAILABLE 221 10 4.5 DBA 990 BMW 316 28 8.5
DBA 934 FORD 268 20.5 4.5 DBA 991 BMW 324 12 6.5
DBA 935 PART NOT AVAILABLE 235 10 4 DBA 995 PART NOT AVAILABLE 319 32 18
DBA 936 PART NOT AVAILABLE 258 20 5 DBA 996A/B CHEVROLET 330 28 12.7
DBA 937 FORD 298 30 11 DBA 997A/B CHEVROLET 304.8 20.5 6.4
DBA 938 FORD 320 26 9.5 DBA 998 CHEVROLET 318 32.5 9.5
DBA 939 FORD 275 20 5 DBA 999A/B CHEVROLET 304.8 20.5 6
DBA 940 MAZDA 246 20 6.5 DBA RRF ROLLS ROYCE 280 16 5.5
DBA 941 PART NOT AVAILABLE 255 20 6 DBA RRR ROLLS ROYCE 275 13 5.5
DBA 942 MAZDA 255 10 3.5 DBA 2000 CHEVROLET 305 29 8.4
DBA 943 PART NOT AVAILABLE 256 24 5 DBA 2001 CHEVROLET 330 30 10
DBA 945 FORD 254 10.2 5.5 DBA 2010 CHEVROLET 330 30 11.6
DBA 946 MAZDA 250 22 7.5 DBA 2011 CHEVROLET 345 20 10.2
DBA 947 MAZDA 294 22 7 DBA 2020 HOLDEN 320 32 11.4
DBA 948 MAZDA 260 10 5.5 DBA 2021 HOLDEN 286 18 6.65
DBA 949 PART NOT AVAILABLE 298 28 7.3 DBA 2026 HOLDEN 298 30 8.2
DBA 950 FORD 258 24 5 DBA 2027 HOLDEN 302 22 7.2
DBA 951 FORD 261 9.5 5 DBA 2028 HOLDEN 321 30 9.2
DBA 952 MAZDA 294 20 5.5 DBA 2029 HOLDEN 324 22 8.3
DBA 953 NISSAN 280 26 6.8 DBA 2032 HOLDEN 236 20 3.9
DBA 954 NISSAN 296 24 7.6 DBA 2033 HOLDEN 252 22 5.5
DBA 955 PART NOT AVAILABLE 274 24 6 DBA 2034 VAUXHAUL 321 28 9.4
DBA 956 MAZDA 286 18 6 DBA 2035 HOLDEN 278 10 4
DBA 957 FORD 278 24 6.3 DBA 2036 HOLDEN 280 25
DBA 958 MAZDA 255.5 24 5.2 DBA 2038 HOLDEN 278 24 6.76
DBA 959 MAZDA 274 28 6.7 DBA 2039 HOLDEN 276 12 5.3

238
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)
DBA 2040 HOLDEN 295 29 7.5 DBA 2221 MITSUBISHI 310 40 13.7
DBA 2044 JAGUAR 300 30 DBA 2222 MITSUBISHI 293 40 11.4
DBA 2045 JAGUAR 288 20 DBA 2229 HYUNDAI 276 22 6
DBA 2046 JAGUAR 305 38 DBA 2241 AUDI 276 25
DBA 2047 JAGUAR 305 20 DBA 2242 VOLKSWAGEN 308 29.5 9.4
DBA 2048 HUMMER 325 38 18 DBA 2243 VOLKSWAGEN 314 22
DBA 2049 HUMMER 330 29 10.9 DBA 2244 VOLKSWAGEN 330 32
DBA 2050 HOLDEN 302 28 8.27 DBA 2245 PORSCHE 329 28 8.5
DBA 2051 CHEVROLET 330 29 11.7 DBA 2246 PORSCHE 350 34 12
DBA 2052 CHEVROLET 296 26 7.5 DBA 2247 VOLKSWAGEN 294 22 6.9
DBA 2053 CHEVROLET 270 14 5 DBA 2248 VOLKSWAGEN 333 33 11.7
DBA 2054 CHEVROLET 315 28 9.6 DBA 2250 MERCEDES BENZ 315 30 10.6
DBA 2055 CHEVROLET 312 12 6.4 DBA 2252 MERCEDES BENZ 330 32 11.7
DBA 2090 LANDROVER 317 30 9.9 DBA 2253 MERCEDES BENZ 330 14 7.6
DBA 2091 LANDROVER 325 20 7.7 DBA 2254 MERCEDES BENZ 350 32 13.1
DBA 2092 LANDROVER 344 30 12 DBA 2255 MERCEDES BENZ 330 22 8.2
DBA 2093 LANDROVER 354 12 9.6 DBA 2266 MERCEDES BENZ 294 24 7.7
DBA 2094 LANDROVER 337.5 30 11.4 DBA 2267 MERCEDES BENZ 258 12 6.2
DBA 2095 LANDROVER 350 20 8.9 DBA 2268 MERCEDES BENZ 285 22
DBA 2096 LANDROVER 360 30 12 DBA 2269 MERCEDES BENZ 298 16 7.2
DBA 2097 LANDROVER 354 20 9.2 DBA 2270 MERCEDES BENZ 299.5 28 9.26
DBA 2098 LANDROVER 360 30 12.2 DBA 2274 PEUGEOT 266 22 5.5
DBA 2099 LANDROVER 344 30 12 DBA 2275 PEUGEOT 283 26 7.1
DBA 2100 FORD 258 22 5.5 DBA 2300 NISSAN 257 22 6
DBA 2101 FORD 300 24 7.1 DBA 2301 NISSAN 278 10 4.5
DBA 2103 FORD 280 10 3.9 DBA 2303 NISSAN 257 10 3.7
DBA 2107 FORD 322 28 10.3 DBA 2306 NISSAN 319 26 8.25
DBA 2108 FORD 322 26 9.2 DBA 2307 NISSAN 319 14 7.5
DBA 2109 FORD 253 10 3.3 DBA 2308 NISSAN 320 28 10.5
DBA 2113 FORD 316 30 9.25 DBA 2309 NISSAN 308 16 6
DBA 2114 FORD 300 19 6 DBA 2310 NISSAN 296 28 7.9
DBA 2115 FORD 293 30 7.4 DBA 2311 NISSAN 308 18 6
DBA 2118 FORD 278 25 6.3 DBA 2312 NISSAN 320 26 9.1
DBA 2119 FORD 265 11 4.1 DBA 2313 NISSAN 308 16 6
DBA 2120 FORD 320 25 9.1 DBA 2314 NISSAN 354.6 32 13.2
DBA 2121 FORD 280 11 4.5 DBA 2315 NISSAN 350 20 8.8
DBA 2124 FORD MUSTANG GT500 355 32 11.1 DBA 2316 NISSAN 296 26
DBA 2125 FORD MUSTANG GT500 330 20.7 6.6 DBA 2352 RENAULT 259 20.6 5
DBA 2141 PROTON 280 12 4.7 DBA 2353 RENAULT 280 24 7.3
DBA 2150 FORD 308 26 DBA 2354 RENAULT 238 8 4
DBA 2151 FORD 308 30 DBA 2360 ALFA ROMEO 272 22 6.1
DBA 2160 FIAT 305 28 8.6 DBA 2380 VOLVO 300 25 8.1
DBA 2170 TRIUMPH 232 9.6 2.75 DBA 2382 VOLVO 286 26 6.9
DBA 2200 MITSUBISHI 256 24 4.9 DBA 2383 VOLVO 288 12 5.4
DBA 2201 MITSUBISHI 276 26 6 DBA 2384 VOLVO 305 28 9.3
DBA 2202 MITSUBISHI 276 26 6 DBA 2390 PORSCHE 322 32
DBA 2203 MITSUBISHI 262 10 4.1 DBA 2392 PORSCHE 322 32 9.6
DBA 2205 MITSUBISHI 262 10 DBA 2394 PORSCHE 318 38 8.2
DBA 2206 MITSUBISHI 294 28 7.2 DBA 2396 PORSCHE 350 34
DBA 2207 MITSUBISHI 302 18 6 DBA 2397 PORSCHE 330 28
DBA 2208 MITSUBISHI 294.4 28 7.1 DBA 2398 PORSCHE 298 24
DBA 2209 MITSUBISHI 262 10 DBA 2431 DODGE 330 22.6 7.4
DBA 2216 MITSUBISHI 332 28 9.2 DBA 2438 CHRYSLER 345 28 10.5
DBA 2219 MITSUBISHI 332 18 8.0 DBA 2439 CHRYSLER 320 22 8.5
DBA 2220 MITSUBISHI 310 40 13.3 DBA 2440 DODGE 287 24 7

239
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 2442 DODGE 336 28 10.4 DBA 2650 SUBARU 316 30 9.69
DBA 2443 DODGE 352 22 10.5 DBA 2657 SUBARU UPGRADE 316 20 9.75
DBA 2444 DODGE 360 32 12.5 DBA 2659 SUBARU 286 10 4.96
DBA 2445 DODGE 350 28 10.5 DBA 2670 BMW 334 32 11.3
DBA 2446 DODGE 280 28 7.2 DBA 2671 BMW 328 20 7.9
DBA 2447 DODGE 270 11.9 4.8 DBA 2700 TOYOTA 338 28 9.4
DBA 2448 DODGE 355 32 12.2 DBA 2701 TOYOTA 271 10 4.6
DBA 2449 DODGE 355 32 12.2 DBA 2702 LEXUS 319 28 10
DBA 2450 HYUNDAI 241 19 DBA 2703 LEXUS 288 10 5.3
DBA 2451 HYUNDAI 256 19 4.9 DBA 2705 TOYOTA 296 28 8
DBA 2452 HYUNDAI 294 26 7.3 DBA 2707 TOYOTA 286 10 5.7
DBA 2454 HYUNDAI 303 28 DBA 2708 TOYOTA 255 20 4.8
DBA 2456 HYUNDAI 300 28 8 DBA 2709 TOYOTA 296 28 7.3
DBA 2457 HYUNDAI 284 10 4.88 DBA 2710 TOYOTA 296 28 8.86
DBA 2458 HYUNDAI 257 24.5 5.9 DBA 2711 TOYOTA 269 12 5.2
DBA 2460 HYUNDAI 300 30 9.8 DBA 2712 LEXUS 296 28 8
DBA 2461 HYUNDAI 324 18 7.5 DBA 2714 TOYOTA 297 25 7.7
DBA 2498 DAIHATSU 246 17 5.3 DBA 2715 TOYOTA 255 28 5.86
DBA 2500 ACURA 300 25 6.6 DBA 2716 TOYOTA 319 28 8.3
DBA 2502 HONDA 260 9 3.9 DBA 2718 TOYOTA 255 22 5.1
DBA 2503 HONDA 282 9 4.5 DBA 2719 TOYOTA 258 9 3.46
DBA 2504 HONDA 240 21 4.4 DBA 2720 LEXUS 334 30 11.6
DBA 2506 HONDA 282 25 6.4 DBA 2721 LEXUS 310 18
DBA 2508 HONDA 300 25 7.5 DBA 2722 TOYOTA 340 32 10.5
DBA 2510 HONDA 300 28 7.7 DBA 2723 TOYOTA 345 18 7.5
DBA 2511 HONDA 260 9 3.75 DBA 2724 TOYOTA 254 32 11.2
DBA 2513 HONDA 260 9 3.6 DBA 2726 TOYOTA 296 28 7.3
DBA 2514 HONDA 282 28 7.1 DBA 2727 LEXUS 291 10 4.8
DBA 2515 HONDA 259.5 10 4.3 DBA 2728 LEXUS 357 34 13.3
DBA 2516 HONDA 282 23 6.4 DBA 2730 TOYOTA 296 28 7.8
DBA 2517 HONDA 260 9.1 3.5 DBA 2731 TOYOTA 298 10 5.16
DBA 2518 HONDA 320 25 8.44 DBA 2732 TOYOTA 285 28 7.8
DBA 2519 HONDA 282 9 4.06 DBA 2734 TOYOTA 328 28
DBA 2524 MINI COOPER 294 22 6.35 DBA 2735 TOYOTA 309 10
DBA 2526 MINI COOPER 280 22 5.8 DBA 2736 TOYOTA PRADO 338 32
DBA 2528 MINI COOPER 316 22 7.44 DBA 2737 TOYOTA PRADO 312 18
DBA 2529 MINI COOPER 280 10 3.76 DBA 2797 FORD 347 38
DBA 2530 JEEP 328 30 10.5 DBA 2798 FORD 347 38
DBA 2531 JEEP 320 14 8 DBA 2799 FORD 340 34
DBA 2532 JEEP 360 32 13.2 DBA 2800 AUDI 312 25 8.8
DBA 2533 JEEP 350 28 12 DBA 2801 AUDI 245 10 3.2
DBA 2535 JEEP 285 12 5.56 DBA 2802 AUDI 255 12 3.8
DBA 2536 JEEP 302 28 7.46 DBA 2803 AUDI 245 10 3.8
DBA 2537 JEEP 316 12 7.2 DBA 2805 AUDI 255 10 4
DBA 2558 MAZDA 314 32 8.62 DBA 2806 VOLKSWAGEN 312 25 8.6
DBA 2559 MAZDA 314 20 6.2 DBA 2807 VOLKSWAGEN 285.6 11.7 4.7
DBA 2560 MAZDA 302.7 26 8.5 DBA 2808 VW 345 30 11.9
DBA 2561 MAZDA 302 12 5.8 DBA 2809 VW 310 22 7.3
DBA 2580 SUZUKI 295 25 6.8 DBA 2815 HOLDEN 308 25 7.8
DBA 2602 CHEVROLET 321 30 DBA 2817 HOLDEN 302 28 8.5
DBA 2603 CHEVROLET 315 23 DBA 2818 HOLDEN 292 20 5.2
DBA 2604 CHEVROLET 355 32 DBA 2819 HOLDEN 314 28 9.2
DBA 2605 CHEVROLET 365 28 DBA 2820 HOLDEN 285 25 6.8
DBA 2606 CHEVROLET 303 30 DBA 2839 HOLDEN 256 26 5.7
DBA 2607 CHEVROLET 278 9 DBA 2840 HOLDEN 280 27 7

240
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)
DBA 2852 BMW 300 20 6 DBA 4027 HOLDEN 290 23 10.5
DBA 2854 BMW 324 30 DBA 4035 HOLDEN 289 23 9
DBA 2855 BMW 328 25 8.9 DBA 4036 HOLDEN 279 10.7 5.5
DBA 2856 BMW 320 22 7.6 DBA 4036B HOLDEN 279 10.7 5.5
DBA 2858 BMW 348 30 11.5 DBA 4037 HOLDEN 279 10.7 5.5
DBA 2859 BMW 336 22 9 DBA 4040 HOLDEN 296 28 9.5
DBA 2860 BMW 330 24 9.06 DBA 4040B HOLDEN 296 28 9.5
DBA 2861 BMW 300 20 6.64 DBA 4041 HOLDEN 286 16 7
DBA 2862 BMW 300 24 8 DBA 4045 HOLDEN 280 20 6
DBA 2868 BMW 324 30 10.4 DBA 4046 HOLDEN 328 28 9.5
DBA 2869 BMW 320 20 7.44 DBA 4046B HOLDEN 328 28 9.5
DBA 2870 KIA 274 28 7 DBA 4047 HOLDEN 280 20 7
DBA 2871 KIA 300 28 7.6 DBA 4048 HOLDEN 330 32 11.3
DBA 2872 KIA 275 26 6.7 DBA 4049 HOLDEN 315 18 8
DBA 2873 KIA 258 10 4.1 DBA 4067 CHEVROLET 325 32 10.1
DBA 2893 KIA 256 22 5.1 DBA 4069 FORD 330 28 9.1
DBA 2894 KIA 257 25 DBA 4086 LANDROVER 298 24 7.5
DBA 2895 KIA 261 9.8 DBA 4087 LANDROVER 298 14 7.75
DBA 2896 KIA 235 22 4.8 DBA 4088 LANDROVER 290 12.7 6.5
DBA 2897 KIA 258 26 7.3 DBA 4092 LANDROVER 297 25 8
DBA 2898 KIA 302 28 7.64 DBA 4093 LANDROVER 304 12.6 7
DBA 2899 KIA 315 20 DBA 4096 JEEP 280 24 6.8
DBA 2948 ROLLS ROYCE 281 31.5 7.9 DBA 4097 JEEP 285 11 5.1
DBA 2949 ROLLS ROYCE 299 31.5 9 DBA 4106H FORD 287 24 11
DBA 2950 MAZDA 274 24 5.75 DBA 4107 FORD 287 24 11
DBA 2951 MAZDA 280 10 8.68 DBA 4110B FORD 287 24 9
DBA 2952 MAZDA 288.5 28 4 DBA 4111A FORD 287 15 6.5
DBA 2954 MAZDA 278 25 7.23 DBA 4111B FORD 287 13 6.5
DBA 2955 MAZDA 264 11 4 DBA 4118 FORD 247 13 4
DBA 2956 MAZDA 300 25 7.95 DBA 4130 FORD 287 24 10.5
DBA 2957 MAZDA 280 11 4.5 DBA 4131 FORD 287 25 10.5
DBA 2958 MAZDA 258 22 5.3 DBA 4132 FORD 287 25 10.5
DBA 2959 MAZDA 290 22 6.25 DBA 4133 FORD 299 10.5 5.6
DBA 2960 MAZDA 320 25 9.4 DBA 4134 FORD 287 24 10
DBA 2961 MAZDA 314 11 5.5 DBA 4135 FORD 287 24 10
DBA 2962 MAZDA 320 25 9.6 DBA 4166 CHRYSLER 270 9 3.9
DBA 2990 CHEVROLET 340 32 10.1 DBA 4167 CHRYSLER 280 23 5.8
DBA 2991 CHEVROLET 330 26 9.1 DBA 4200 HONDA 282 23 6
DBA 2992 CHEVROLET 355 32 11.8 DBA 4213 DODGE 296 30 7
DBA 2993 CHEVROLET 340 26 9.4 DBA 4214 DODGE 284 20 5.8
DBA 2994 CHEVROLET 325 32 10 DBA 4216 DODGE 314 30 8.6
DBA 2995 CHEVROLET 305 26 6.8 DBA 4217 DODGE 297 20 6.5
DBA 2996 CHEVROLET 303 32 9.75 DBA 4240 AUDI 321 30 9.5
DBA 2997 CHEVROLET 305 26 7.3 DBA 4241 AUDI 269 22 5
DBA 7420 TOYOTA 318 28 8.3 DBA 4242 AUDI 321 30 10
DBA 4329 NISSAN 295 20 7
DBA 4356 ALFA ROMEO 284 22 5.8
4000 SERIES DBA 4402 MITSUBISHI 276 24 6
DBA 4000 SUBARU 295 25 7.8 DBA 4417 MITSUBISHI 294 24 6.3
DBA 4014 HOLDEN 276 25.4 11 DBA 4418 MITSUBISHI 320 32 9.75
DBA 4015 HOLDEN 270 22 10.5 DBA 4419 MITSUBISHI 300 22 7
DBA 4016 HOLDEN 279 10.5 5.5 DBA 4425 MITSUBISHI 276 24 6
DBA 4017 HOLDEN 290 22 11 DBA 4428 MITSUBISHI 276 24 5.6
DBA 4019 HOLDEN 330 28 13 DBA 4429 MITSUBISHI 284 20 6.1
DBA 4020 HOLDEN 278 20 6 DBA 4456 HYUNDAI 257 24 4.8

241
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)
DBA 4468 HYUNDAI 280 26 7 DBA 4654-10 SUBARU 326 30 9.5
DBA 4469 HYUNDAI 258 10 4.1 DBA 4655-10 SUBARU 316 20 8
DBA 4474 HONDA 262 21 5 DBA 4656 SUBARU 290 18 5.7
DBA 4475 HONDA 239 9 3 DBA 4657 SUBARU 290 10 4.9
DBA 4476 HONDA 300 28 8 DBA 4660 MITSUBISHI 290 26 0
DBA 4478 HONDA 282 23 6.5 DBA 4661 MITSUBISHI 300 22 6.5
DBA 4479 HONDA 282 9 4.2 DBA 4663 MITSUBISHI 276 24 6
DBA 4482 HONDA 300 25 7 DBA 4665 ALFA ROMEO 284 22 6.5
DBA 4483 HONDA 282 12 4.5 DBA 4698 NISSAN 316 34 10.5
DBA 4484 HONDA 282 28 6.5 DBA 4699 NISSAN 330 18 7.6
DBA 4486 HONDA 298 28 6.8 DBA 4718 LEXUS 323 30 9.3
DBA 4487 HONDA 303 23 6.5 DBA 4719 TOYOTA 324 16 5.7
DBA 4488 HONDA 282 23 6.5 DBA 4735 TOYOTA 275 28 7
DBA 4500 FORD 287 24 7 DBA 4746 LEXUS 307 16 5.6
DBA 4501 FORD 287 10.5 5 DBA 4748 LEXUS 296 32 9
DBA 4502 FORD 287 28 7 DBA 4749 TOYOTA 307 12 6
DBA 4503 FORD 287 16 6.5 DBA 4769 ALFA ROMEO 305 28 7.6
DBA 4504 FORD 298 28 9 DBA 4773 CHEVROLET 295 33 8
DBA 4505 FORD 303 16 7.5 DBA 4784 TOYOTA 311 32 9.66
DBA 4506 FORD 329 28 9 DBA 4788 LEXUS 312 32 9.5
DBA 4507A FORD 330 28 9.9 DBA 4789 LEXUS 330 18 8.25
DBA 4507B FORD 330 28 9.9 DBA 4790 TOYOTA 322 22 8.5
DBA 4526 LANDROVER 262 14 4.9 DBA 4791 TOYOTA 335 18 7.5
DBA 4527 LANDROVER 277 21 5.9 DBA 4796 FORD 326 30 11.2
DBA 4528 LANDROVER 297 25 8.8 DBA 4798 FORD 331 38 13
DBA 4531 FORD 231 9 3 DBA 4799 FORD 326 30 11.5
DBA 4532 FORD 235 22 4.5 DBA 4838 AUDI 312 25 8
DBA 4533 FORD 257 22 5.2 DBA 4840 GM 280 26 6.5
DBA 4534 MAZDA 250 9 3 DBA 4841 GM 313 18 7
DBA 4538 MAZDA 255 20 5 DBA 4878 KIA 274 26 7.2
DBA 4540 JEEP 305 26 8 DBA 4888 JEEP 280 24.5 6.8
DBA 4541 JEEP 305 10 6 DBA 4901 NISSAN 257 26 6.5
DBA 4542 MINI COOPER 276 22 3.4 DBA 4906 NISSAN 258 9 3.5
DBA 4543 MINI COOPER 259 10 3.4 DBA 4908 NISSAN 292 18 6.5
DBA 4545 MAZDA 270 22 6 DBA 4909 NISSAN 280 30 7
DBA 4546 MAZDA 276 10 4 DBA 4926 NISSAN 296 32 8.1
DBA 4549 LANDROVER 298 14 6.8 DBA 4928 NISSAN 324 30 9
DBA 4552 MERCEDES BENZ 345 32 11.2 DBA 4929 NISSAN 300 22 8
DBA 4553 MERCEDES BENZ 331 14 8 DBA 4947 MAZDA 294 22 7
DBA 4560 TOYOTA 315 32 10.5 DBA 4954 NISSAN 296 24 7.07
DBA 4562 TOYOTA 275 25 6.2 DBA 4957 FORD 278 24 7
DBA 4563 TOYOTA 269 9 3.6 DBA 4963 NISSAN 296 30 8
DBA 4569 AUDI 256 22 4.8 DBA 4966 BMW 300 22 6.7
DBA 4573 NISSAN 280 28 7.5 DBA 4979 BMW 286 22 6
DBA 4574 NISSAN 292 16 5 DBA 4984 BMW 315 28 9.5
DBA 4575 AUDI 321 30 10 DBA 4993 FORMULA FORD 248 7 1.55
DBA 4600 NISSAN 324 30 9.5 DBA 4994 FORMULA FORD 248 7 2.5
DBA 4601 NISSAN 322 22 8 DBA 4996 CHEVROLET 330 28 9.9
DBA 4622 NISSAN 315 18 7.5 DBA 42000 CHEVROLET 305 29 8.5
DBA 4625 NISSAN 306 32 10.4 DBA 42001 CHEVROLET 330 30 10
DBA 4644 SUBARU 266 10 4.5 DBA 42019 HOLDEN 332 24
DBA 4648 SUBARU 277 24 8 DBA 42020 HOLDEN 320 32 11.48
DBA 4649 SUBARU 266 18 5 DBA 42021 HOLDEN 286 18 6.8
DBA 4650 SUBARU 294 24 7 DBA 42022 HOLDEN 336 32 10.8
DBA 4653 SUBARU 290 18 6 DBA 42025 HOLDEN 343 26 9.8

242
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)

DBA 42028 HOLDEN 321 30 9.2 DBA 42396 PORSCHE 350 34 11.6
DBA 42030 HOLDEN 365 32 11 DBA 42397 PORSCHE 330 28 9.1
DBA 42031 HOLDEN 350 26 10.3 DBA 42398 PORSCHE 298 24
DBA 42034 VAUXHAUL 321 28 9.4 DBA 42429 MITSUBISHI 284 20
DBA 42035 HOLDEN 278 10 4 DBA 42431 DODGE 330 22.6 7.4
DBA 42048 CHEVROLET 325 38 12 DBA 42438 CHRYSLER 345 28 10.5
DBA 42049 CHEVROLET 330 29 10.9 DBA 42439 CHRYSLER 320 22 8.5
DBA 42050 HOLDEN 302 28 7.2 DBA 42444 CHRYSLER 360 32 12.5
DBA 42051 CHEVROLET 330 29 11.5 DBA 42445 CHRYSLER 350 28 10.5
DBA 42052 CHEVROLET 296 26 0 DBA 42448 CHRYSLER 345 32 12.4
DBA 42053 CHEVROLET 270 14 5 DBA 42449 CHRYSLER 320 32 12.3
DBA 42054 CHEVROLET 315 28 9.6 DBA 42456 HYUNDAI 300 28 8
DBA 42055 CHEVROLET 312 12 6.4 DBA 42500 HONDA 300 25 6.6
DBA 42090 LANDROVER 317 30 9.9 DBA 42506 HONDA 282 25 6.37
DBA 42091 LANDROVER 325 20 7.6 DBA 42508 HONDA 300 25 7.5
DBA 42092 LANDROVER 344 30 12 DBA 42510 HONDA 300 28 7.5
DBA 42093 LANDROVER 354 12 9.6 DBA 42514 HONDA 282 28 7.1
DBA 42094 LANDROVER 338 30 11.4 DBA 42515 HONDA 260 10 4.3
DBA 42095 LANDROVER 350 20 8.8 DBA 42524 MINI COOPER 294 22 6.5
DBA 42096 LANDROVER 360 30 11.9 DBA 42526 MINI COOPER 280 22 5.8
DBA 42097 LANDROVER 354 20 9 DBA 42530 JEEP 328 30 10.5
DBA 42098 LANDROVER 360 30 12 DBA 42531 JEEP 320 14 8
DBA 42100 FORD 258 22 5.5 DBA 42532 JEEP 360 32 13.2
DBA 42102 FORD 355 32 12.6 DBA 42533 JEEP 350 28 12
DBA 42104 FORD 325 32 9.5 DBA 42550 MAZDA 320 24 8.44
DBA 42107 FORD 322 28 10.3 DBA 42551 MAZDA 300 18 5.5
DBA 42108 FORD 328 26 9.5 DBA 42552 MAZDA 302.5 24 7.5
DBA 42113 FORD 316 30 9.25 DBA 42560 MAZDA 302.7 26 8.5
DBA 42114 FORD 300 19 6 DBA 42561 MAZDA 302 12 5.8
DBA 42115 FORD 293 30 7.4 DBA 42575 AUDI 344.5 30 10.5
DBA 42120 FORD 320 25 9.1 DBA 42576 AUDI 300 22 6
DBA 42121 FORD 280 11 4.5 DBA 42580 SUZUKI 295 25 6.8
DBA 42140 PROTON 266 22 4.7 DBA 42650 SUBARU 316 30 9.7
DBA 42160 FIAT 305 28 8 DBA 42656 SUBARU 316 20 7.73
DBA 42206 MITSUBISHI 294 28 7.2 DBA 42657 SUBARU REAR UPGRADE 316 20 9.2
DBA 42207 MITSUBISHI 302 18 6 DBA 42700 TOYOTA 338 28 9.4
DBA 42224 MITSUBISHI 350 32 11.8 DBA 42702 TOYOTA 320 28 8.2
DBA 42225 MITSUBISHI 330 22 8.8 DBA 42705 TOYOTA 296 28 8
DBA 42245 PORSCHE 330 28 8.5 DBA 42709 TOYOTA 296 28 7.3
DBA 42246 PORSCHE 350 34 12 DBA 42714 TOYOTA 297 25 7.5
DBA 42250 MERCEDES BENZ 315 30 10 DBA 42715 TOYOTA 255 28 5.86
DBA 42301 NISSAN 278 10 4.5 DBA 42716 TOYOTA 319 28 8.3
DBA 42304 NISSAN 310 30 9.5 DBA 42800 AUDI 312 25 8.8
DBA 42306 NISSAN 319 26 8.1 DBA 42806 VOLKSWAGEN 312 25 8.6
DBA 42307 NISSAN 319.5 14 7.5 DBA 42807 VOLKSWAGEN 285.6 11.7 4.7
DBA 42308 NISSAN 320 28 10.5 DBA 42815 HOLDEN 308 25.1 7.8
DBA 42309 NISSAN 308 16 6 DBA 42819 HOLDEN 314 28 9.2
DBA 42310 NISSAN 296 28 7.9 DBA 42840 HOLDEN 280 27 7
DBA 42311 NISSAN 308 18 6 DBA 42850 BMW 325 28 9
DBA 42313 NISSAN 308 16 6 DBA 42851 BMW 327 20 8
DBA 42355 LOTUS 288 26 6.1 DBA 42858 BMW 348 30 11.5
DBA 42360 ALFA ROMEO 272 22 6.25 DBA 42859 BMW 336 22 9
DBA 42390 PORSCHE 322 32 DBA 42870 KIA 274 28 7
DBA 42392 PORSCHE 322 32 9.6 DBA 42871 KIA 300 28 7.6
DBA 42394 PORSCHE 318 28 8.2 DBA 42898 KIA 302 28 8

243
WeightS & DIMENSIONS CHART
DBA# application / make diam thick weight DBA# application / make diam thick weight
(mm) (mm) (kg) (mm) (mm) (kg)
DBA 42951 MAZDA 280 10 4.3 DBA 52323 NISSAN GTR35 - OE REAR 380
DBA 42952 FORD 288.5 28 8.5 DBA 52355 LOTUS 288 25.7 5.4
DBA 42956 MAZDA 300 25 7.5 DBA 52356 LOTUS 280 26 6
DBA 42957 MAZDA 280 11 4.5 DBA 52358 LOTUS UPGRADE OPTION 296 26 5.5
DBA 42959 MAZDA 290 22 6.2 DBA 52386 PORSCHE 330 34
DBA 42960 MAZDA 320 25 9 DBA 52390 PORSCHE 322 32 9.1
DBA 42961 MAZDA 314 11 5.5 DBA 52396 PORSCHE 350 34
DBA 42962 MAZDA 320 25 9.6 DBA 52398 PORSCHE 298 24
DBA 42990 CHEVROLET 340 32 10.5 DBA 52399 PORSCHE 379.5 32 9.76
DBA 42991 CHEVROLET 330 26 9.1 DBA 52430 DODGE 330 32 9.5
DBA 42992 CHEVROLET 355 32 12.25 DBA 52448 DODGE 355 32 10.7
DBA 42993 CHEVROLET 340 26 9.25 DBA 52468 HYUNDAI 320 27 7.2
DBA 42994 CHEVROLET 325 32 10.25 DBA 52500 ACURA 300 25 6.3
DBA 42995 CHEVROLET 305 26 6.75 DBA 52508 ACURA 300 25 6.5
DBA 42996 CHEVROLET 303 32 9.75 DBA 52525 MINI COOPER 320 28 6.8
DBA 42997 CHEVROLET 305 26 7.25 DBA 52550 MAZDA 320 24 8.1
DBA 42999 FORMULA FORD 254 9.65 2.21 DBA 52604 CHEVROLET 355 32
DBA 52650 SUBARU 316 30 9

5000 SERIES DBA 52804 AUDI 360 32

DBA 52850 BMW 325 28 7.5
DBA 5000 SUBARU 294 25 6 DBA 52880 BMW 325 28 7.5
DBA 5003.1 FORMULA 3 278 15.9 2.7 DBA 52990 CHEVROLET 340 32 9.6
DBA 5010 SUBARU 294 25 6.9 DBA 52992 CHEVROLET 355 32 10.5
DBA 5040 GM 296 28 7.75 DBA 52994 CHEVROLET 325 32 9.25
DBA 5046 HOLDEN 328 28 9.4
DBA 5046B HOLDEN 328 28 9.4
DBA 5048 GM 330 32 8.55
DBA 5055 GM 343 32 8.8
DBA 5067 GM 325 32 8.5
DBA 5069 FORD 330 28 8.2
DBA 5240 AUDI 321 30 9.25
DBA 5242 AUDI 321 30 8.4
DBA 5355 LOTUS 282 26 5.6
DBA 5417 MITSUBISHI 294 24 6.6
DBA 5418.1 MITSUBISHI 320 32 8
DBA 5468 HYUNDAI 320 28 8.3
DBA 5506 FORD 329 28 9.2
DBA 5575 AUDI 320 30 9
DBA 5600 NISSAN 324 30 9
DBA 5654-10 SUBARU 326 30 8.96
DBA 5718 TOYOTA 323 30 8.6
DBA 5928 NISSAN 324 30 8.4
DBA 52018 HOLDEN 350 32 9.6
DBA 52020 HOLDEN 320 32 9.5
DBA 52024 HOLDEN 362 32 10.5
DBA 52030 HOLDEN 365 32 11
DBA 52070 JAGUAR 355 32 9.7
DBA 52102 FORD 355 32 9.7
DBA 52104 FORD 325 32 9
DBA 52113 FORD 319 30 8.5
DBA 52218 MITSUBISHI 320 32 9
DBA 52320 NISSAN GTR35 FRONT 380 34 11
DBA 52321 NISSAN GTR35 REAR 380
DBA 52322 NISSAN GTR35 - OE FRONT 380 34 10.2

244
 A = Diameter D = Min. Thickness
B = Original Height E = Centrel Hole Diameter
C = Original Thickness F = No. of Bolt Holes

Model Years F/R DBA S X 4000 5000 Solid Dimensions (mm)

No. Series Series Vented A B C D E F

The Kangaroo Paw design is not available on all part numbers, ask your supplier for details. 245