Scribd
Upload
87 views

Blast Patterns and Explosive Distribution

This document discusses terminology and geometry used in open pit blasting, including burden, spacing, powder factor, and blast patterns. It explains that burden is the shortest distance to a free face, and powder factor expresses the amount of explosive used per volume of rock blasted. Various blasthole patterns like square and staggered are presented, and factors that influence powder factor such as explosive type, rock properties, and hole geometry are described. Angled versus vertical blasthole drilling is also briefly discussed.

Uploaded by

Iven Tan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
87 views

Blast Patterns and Explosive Distribution

This document discusses terminology and geometry used in open pit blasting, including burden, spacing, powder factor, and blast patterns. It explains that burden is the shortest distance to a free face, and powder factor expresses the amount of explosive used per volume of rock blasted. Various blasthole patterns like square and staggered are presented, and factors that influence powder factor such as explosive type, rock properties, and hole geometry are described. Angled versus vertical blasthole drilling is also briefly discussed.

Uploaded by

Iven Tan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Blast Patterns and Explosive

Distribution

Abbas Taheri
Terminology and geometry of open pit blasts

Stemming

Burden
Bench Height
Hole Length

Sub-drill

Cross Section through a single hole in a bench blast

The burden for an explosive charge is the shortest distance to a free face or
plane of relief.
It is therefore the direction in which it is expected that most work will be
done by the explosive charge.
Drilling Patterns
• An even distribution of explosives requires an even distribution of holes

Square pattern Staggered pattern


S:B = 1 S:B = 2
Effective Burden

Effective Spacing

The significance of burden


Blast patterns
• Patterns of holes are used to blast
large areas.

• These holes can be arranged in


different patterns relative to each
other and relative to the blast
boundaries.

• The relationship between burden


and spacing can vary over a wide
range to suit the distribution of
explosives and initiation pattern
required. Staggered blasthole pattern with two
free faces
Powder factor
Each hole is theoretically responsible for
blasting the bench height multiplied by
the spacing multiplied by the burden.

The amount of explosive that contributes


to blasting this volume includes the
explosive in the sub-drill because if this
were not provided it is likely that
breakage would be inadequate at the
grade of the new bench.

kilograms per bank cubic metre (kg/m3)


kilograms per tonne (kg/t)
Powder factor

• Powder factor is a convenient way to express the overall


amount of explosive that is used in a blast and is therefore a
convenient accounting concept.

• However it can be extended to describe the explosive


concentration and its variability within a blast volume.

• The work done by the explosive can be related to the


explosive concentration.
Problems with Powder Factor
• No guidance as to how specific blasting outcomes can be achieved.
• Rock mass dynamic and structural properties are ignored.
• “Powder Factor” is ambiguous.
• The actual sequence of events and blast hole timing are not considered.

However the Powder Factor gives you a general idea of blasting design

Bench blasting (2 free face): 0.2, 0.3, 0.4, 0.5


>> varied by Explosive type, Rock hardness, discontinuities condition, water etc.
Bench height etc.

Underground Tunnelling (1 free face): 0.7 ~ 1.5


>> varied by Explosive type, Rock hardness, discontinuities condition, water etc.
size of drift, cut design etc.
Powder factor
• This Figure shows the energy concentration on a cross section
through a blast pattern.

• The role of sub-drill ensuring breakage down to the new bench


floor and the impact of the stemming zone reducing the
explosive concentration near the bench surface are both
apparent on the plot.
Powder factor
Powder factor

A blast design using 127 mm diameter blastholes on a staggered pattern providing an


overall powder factor of 0.5 kg/bcm using ANFO.
The pattern shows a very even distribution of energy at concentrations above 2
kg/bcm. A fragmentation model indicates that the mean fragment size from this
blast would be 175 mm.
Powder factor

A pattern using 250 mm diameter blastholes in the same geometry and


providing the same powder factor.

The explosive concentration is clearly less even and fragmentation


modelling indicates that the mean fragment size would increase by 15%
to 202 mm.
Vertical blast hole
Angled blastholes
Angled blastholes
• Many open pit blasthole drills can drill angled holes, but this is
usually limited to within 20o of vertical for large diameter rigs.

• Drilling angled holes can increase the rate of wear on drill pipes

• Angled holes can suffer stability problems in broken or weak


ground.

• The length of the blasthole is increased compared with vertical


drilling and this difference needs to be taken into account in
charge calculations.

You might also like