Scribd
Upload
160 views

Column-Ppt Slides

Uploaded by

Mary Grace
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
160 views

Column-Ppt Slides

Uploaded by

Mary Grace
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 23

Objectives

 Understand the behavior of columns and concept of


critical load and buckling
 Determine the axial load needed to buckle a so-called
‘ideal’ column
 Determine the ‘effective length’ of a column with
various end-conditions
 Design a realistic column against buckling
Structural Failures
• Buckling Failure
– The more slender the member, the smaller is
its buckling load.
APPLICATIONS
Structural Failures
– Solid blocking in a wood frame wall to prevent
the buckling of studs
– Lateral buckling of slender beams or joists
• In wood floor joists (which are quite slender),
lateral buckling is prevented by using solid
blocking between joists.
Structural Failures
– Horizontal ties in a
reinforced concrete
column prevent the
buckling of vertical
reinforcement due to
the compressive load
on the column.
APPLICATIONS
APPLICATIONS (cont)
APPLICATIONS (cont)
My notes
IDEAL COLUMN
• Ideal column
– It is perfectly straight before loading
– Both ends are pin-supported
– Loads are applied throughout the centroid of the cross section

• Behavior
– When P < Pcr, the column remains straight.
– When P = Pcr,
d 2v
EI 2  M   Pv
dx
d 2v  P 
  v  0
dx  EI 
2

 P   P 

v  C1 sin  x   C2 cos
 x 
 EI   EI 
IDEAL COLUMN (cont)
• Since v = 0 at x = 0, then C2 = 0

 P 
• Since v = 0 at x = L, then C1 sin  L   0
 EI 
 P 
• Therefore, sin  L   0
 EI 
 P 
• Which is satisfied if sin  EI L   n
 
n 2 2 EI
• Or P 2
where n  1,2,3,...
L
IDEAL COLUMN (cont)
 2 EI
• Smallest value at P is when n = 1, thus Pcr 
L2
 2E
• Corresponding stress is  cr 
KL / r 2
• Where r = √ (I/A) is called ‘radius of gyration’

• (L/r) is called the ‘slenderness ratio’.

• The critical-stress curves are


hyperbolic, valid only for σcr
is below yield stress
EXAMPLE 1
The A-36 steel W200 46 member shown below is to be used as
a pin-connected column. Determine the largest axial load it can
support before it either begins to buckle or the steel yields.
EXAMPLE 1 (cont)
Solutions
• From Appendix B,

A  5890 mm2 , I x  45.5 106 mm4 , I y  15.3 106 mm4

• By inspection, buckling will occur about the y–y axis.

 2 EI  2 200 106 15.3 104 1 / 10004


Pcr    1887.6 kN
L2 42
• When fully loaded, the average compressive stress in the column is
Pcr 1887.6 1000
 cr    320.5 N/mm2
A 5890
• Since this stress exceeds the yield stress,
P
250   P  1472.5 kN  1.47 MN (Ans)
5890
COLUMNS HAVING VARIOUS END-CONDITIONS

• Consider the moment-deflection equation for the


cantilevered column, which is fixed at the base.
d 2v
EI 2  P  v 
dx
P
EIV   v    where  
2 2 2

EI

• The solution is v  C1 sin x   C2 cosx   

• Since v = 0 at x = 0, so that C2  

• Also, v'  C1 cosx   C2 sin x 

• Since v’ = 0 at x = 0, so that C1  0
COLUMNS HAVING VARIOUS END-CONDITIONS
(cont)
v   1  cosx x  0
• Hence

• Since v = δ at x = L, thus
 cosL   0
n
 cosL   0 or L 
2

• The smallest critical load


occurs when n = 1, thus
 2 EI  2 EI
Pcr  or Pcr  with k  2
4L 2
kL 2

• k is called the ‘effective-length factor’


COLUMNS HAVING VARIOUS END-CONDITIONS
(cont)
• k for various end conditions:
EXAMPLE 2
A W150 24 steel column is 8 m long and is fixed at its ends as
shown in Fig. below. Its load-carrying capacity is increased by
bracing it about the y–y (weak) axis using struts that are
assumed to be pin connected to its mid-height. Determine the
load it can support so that the column does not buckle nor the
material exceed the yield stress. Take Est = 200 GPa and σY =
410 MPa.
EXAMPLE 2 (cont)
Solutions
• Effective length for buckling about the x–x and y–y axis is

KL x  0.58  4 m  4000 mm


KL y  0.78 / 2  2.8 m  2800 mm
• From the table in Appendix,

 
I x  13.4 106 mm4
Iy  1.8310  mm
6 4

• Applying critical load equation,

 2 EI  2 20013.4106 
Pcr x    1653.2 kN (1)
KL 2
x
4000 2

 2 EI  2 2001.83106 
Pcr x    460.8 kN (2)
KL 2
y
2800 2

Copyright ©2014 Pearson Education, All Rights Reserved


EXAMPLE 2 (cont)
Solutions
• By comparison, buckling will occur about the y–y axis.

• The average compressive stress in the column is

Per 460.8103 
 cr    150.6 N/mm2  150.6 MPa
A 3060
• Since this stress is less than the yield stress,
buckling will occur before the material yields.

• Thus, Pcr  461 kN (Ans)

• it can be seen that buckling will always


occur about the column axis having the largest
slenderness ratio, since it will give a small critical stress
ALLOWABLE STRESS IN DESIGN PRACTICE
• Practically, columns are not perfectly straight as assumed in
theory. By performing experimental tests on a large number of
axially loaded columns, the results may be plotted and a design
formula developed by curve-fitting the mean of the data.

• Note: The experimental curve is similar to that determined from the


secant formula. It accounts for the influence of an “accidental”
eccentricity ratio on the column’s strength.

You might also like