Scribd
Upload
46 views

Title of The Project

This document appears to be a project report submitted by a student named [NAME OF THE STUDENT] to fulfill the requirements of a Bachelor of Technology degree in Electrical and Electronics Engineering from Cochin University of Science and Technology. The report includes certification from the student's guides, an acknowledgement, abstract, table of contents, and multiple chapters discussing the project title, conclusions, and references.

Uploaded by

Nidi Jacob
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
46 views

Title of The Project

This document appears to be a project report submitted by a student named [NAME OF THE STUDENT] to fulfill the requirements of a Bachelor of Technology degree in Electrical and Electronics Engineering from Cochin University of Science and Technology. The report includes certification from the student's guides, an acknowledgement, abstract, table of contents, and multiple chapters discussing the project title, conclusions, and references.

Uploaded by

Nidi Jacob
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

TITLE OF THE PROJECT

PROJECT REPORT

Submitted in partial fulfillment of the requirements for the award of the


Bachelor of Technology Degree in Electrical ad Electronics Engineering
of the Cochin University of Science and Technology

By

NAME OF THE STUDENT/S

DIVISION OF ELECTRICAL AND ELECTRONICS ENGINEERING


SCHOOL OF ENGINEERING
COCHIN UNIVERSITY OF SCIENCE AND TECHNOLOGY
KOCHI – 682022

20xx
DIVISION OF ELECTRICAL AND ELECTRONICS ENGINEERING
SCHOOL OF ENGINEERING
COCHIN UNIVERSITY OF SCIENCE AND TECHNOLOGY

20xx

CERTIFICATE

This is to certify that this project report entitled


TITLE OF THE PROJECT
is a bonafide record of the project work done by Mr. Name of the Student under our
guidance towards the partial fulfillment of the requirements for the award of B.Tech.
degree in Electrical and Electronics Engineering of the Cochin University of Science and
Technology during the year 20xx-20xx.

Guided By Guided By

NAME OF THE GUIDE NAME OF THE GUIDE


Designation Designation
Organization Organization
Place Place

Project Coordinator Head of the Department

NAME OF THE TEACHER NAME OF THE TEACHER


Designation Designation
Organization Division of Electrical and Electronics
Place Engineering
S.O.E., CUSAT
ACKNOWLEDGEMENT

I wish to thank my guide Prof. XYZ, Division of Electrical and Electronics Engineering for
his/her constant encouragement and invaluable help throughout the project period.
I am grateful to Mr. XYD for his constant help and support. This is the second
paragraph of the acknowledgement.
This is the third paragraph of the acknowledgement. The line spacing is 1.5.
Additional spaces should not be inserted in-between two consecutive paragraphs.

NAME OF THE STUDENT


ABSTRACT

The abstract of the project work done should be explained briefly here. This should not
exceed more than one page. If required, the abstract can be divided into paragraphs.
The second paragraph of the abstract goes here.
CONTENTS

Chapter 1 Introduction 1
1.1 Section Heading……………………………………………………………………….. 2
1.1.1 Sub-section Heading……………………………………………………… 3
1.1.2 Sub-section Heading……………………………………………………… 4
1.2 Section Heading……………………………………………………………………….. 5
Chapter 2 Chapter Title 6
2.1 Section Heading……………………………………………………………………….. 7
2.2 Section Heading……………………………………………………………………….. 8
2.2.1 Sub-section Heading……………………………………………………… 9
2.2.2 Sub-section Heading……………………………………………………… 10
Chapter 3 Chapter Title 11
3.1 Section Heading 12
3.1.1 Sub-section Heading 13
3.2 Section Heading 14
. .
. .
. .
Chapter n Conclusions and Future Work 15
References 16
Appendix Appendix Title (If required) 17
NOMENCLATURE

Ia Armature current

 Flux
V Voltage
f Frequency

Note: The symbols should be entered using the equation editor feature in Microsoft Word. The symbols
are to be entered using the equation editor, wherever possible throughout the report. There should be a
spacing of 1.5 between two symbol description lines.
CHAPTER 1

INTRODUCTION

The first paragraph under any section or sub-section should not be given an indent. The
indent should be inserted for every subsequent paragraph. Follow the fonts given in this
template strictly, throughout the report.
The second paragraph started with an indent. All the paragraphs should be
justified (alignment).
All the reports should have an introduction section. The student has to give a brief
introduction to the project chosen, the problems relevant in the area and the solutions
already available, etc.

Division of Electrical and Electronics Engineering 1


CHAPTER 2

CHAPTER TITLE

The second chapter goes on…

2.1 Section Heading


As mentioned earlier, the paragraph is started without an indent. The indent is given
from the second paragraph onwards.
The second paragraph starts here.

2.2 Section Heading


Some text goes here. The section headings should be in 12pt. size with bold letters. The
figures should be inserted in line with the text and should be numbered in the format
shown below. All the figures should have a caption and should be center aligned
together with the figure.

Figure 2.1: Caption for the figure.


This is the second paragraph of the section. When referencing to the figure, it
should be given as, Figure 2.1 and not as Fig. 2.2 or fig. 2.1 or figure 2.1.
Title Item
A B
C D
E F

Table 2.1: Description of Table

Division of Electrical and Electronics Engineering 2


All the tables should be numbered as shown and given a description. The table and
its description should center aligned.

2.2.1 Sub-section Heading


First paragraph of the sub-section is not given an indent. The sub-section heading
should 12pt. size.
This is the second paragraph of the sub-section. All the equations in the report
should be entered using the equation editor feature available in the Microsoft word
package. All the equation should be center aligned and should be assigned a number
according to the format shown below.
ZNP
Eb  (2.1)
60 A
The equations should be referenced as Eq. (2.1) when used in-between sentences
and should be referenced as Equation (2.1) when used in the beginning of the sentence.
It is preferred not to describe the variables in the equation here. It is a good practice to
define the variables in the nomenclature section.

Division of Electrical and Electronics Engineering 3


CHAPTER n

CONCLUSIONS AND FUTURE WORK

The last chapter goes on…

3.1 Section Heading


All the reports should have a conclusions chapter.

Division of Electrical and Electronics Engineering 4


REFERENCES

[1] First reference goes here. Each reference should be numbered. The text here
should be aligned as justify.
[2] When the reference to an item here is made in the report, it should given as [1] or
[2] and not as reference [1] or reference 1 or (1) i.e. the reference number should
be enclosed in square brackets.

Division of Electrical and Electronics Engineering 5


APPENDIX

APPENDIX TITLE

Appendix text goes here…

Division of Electrical and Electronics Engineering 6

You might also like