The LP239 is obsolete


   
   
and is no longer supplied.
SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004

D Wide Supply-Voltage Range . . . 3 V to 30 V D OR N PACKAGE

(TOP VIEW)
D Ultralow Power Supply Current
Drain . . . 60 µA Typ
1OUT 1 14 3OUT
D Low Input Biasing Current . . . 3 nA
2OUT 2 13 4OUT
D Low Input Offset Current . . . ±0.5 nA VCC 3 12 GND
D Low Input Offset Voltage . . . ±2 mV 2IN − 4 11 4IN +
D Common-Mode Input Voltage Includes 2IN + 5 10 4IN −
Ground 1IN − 6 9 3IN +
D Output Voltage Compatible With MOS and 1IN + 7 8 3IN −
CMOS Logic
D High Output Sink-Current Capability
(30 mA at VO = 2V)
D Power Supply Input Reverse-Voltage
Protected
D Single-Power-Supply Operation
D Pin-for-Pin Compatible With LM239, LM339,
LM2901

description/ordering information
The LP239, LP339, LP2901 are low-power quadruple differential comparators. Each device consists of four
independent voltage comparators designed specifically to operate from a single power supply and typically to
draw 60-µA drain current over a wide range of voltages. Operation from split power supplies also is possible
and the ultra-low power-supply drain current is independent of the power-supply voltage.
Applications include limit comparators, simple analog-to-digital converters, pulse generators, squarewave
generators, time-delay generators, voltage-controlled oscillators, multivibrators, and high-voltage logic gates.
The LP239, LP339, LP2901 were designed specifically to interface with the CMOS logic family. The ultra-low
power-supply current makes these products desirable in battery-powered applications.
The LP239 is characterized for operation from −25°C to 85°C. The LP339 is characterized for operation from
0°C to 70°C. The LP2901 is characterized for operation from −40°C to 85°C.

ORDERING INFORMATION
VIOMAX ORDERABLE TOP-SIDE
TA PACKAGE†
AT 25°C PART NUMBER MARKING
PDIP (N) Tube of 25 LP339N LP339N
0°C
0 C to 70
70°C
C ± 5 mV Tube of 50 LP339D
SOIC (D) LP339
Reel of 2500 LP339DR
PDIP (N) Tube of 25 LP2901N LP2901N
−40°C
−40 C to 85
85°C
C ± 5 mV Tube of 50 LP2901D
SOIC (D) LP2901
Reel of 2500 LP2901DR
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

    ! " #$%! "  &$'(#! )!%* Copyright  2004, Texas Instruments Incorporated
)$#!" # ! "&%##!" &% !+% !%"  %," "!$%!"
"!)) -!.* )$#! &#%""/ )%" ! %#%""(. #($)%
!%"!/  (( &%!%"*

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1








   
    The LP239 is obsolete
and is no longer supplied.
SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004

schematic diagram (each comparator)

VCC

0.2 µA
5 µA 0.2 µA 6 µA

IN+
OUT

IN−

GND

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±36 V
Input voltage range, VI (either input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 36 V
Input current, VI ≤ −0.3 V (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Duration of output short-circuit to ground (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Continuous total dissipation (see Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: LP239 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C
LP339 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
LP2901 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
Package thermal impedance, θJA (see Notes 6 and 7): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80°C/W
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature range 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . 300°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated in the recommended operating conditions is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the network ground.
2. Differential voltages are at IN+ with respect to IN −.
3. This input current only exists when the voltage at any of the inputs is driven negative. The current flows through the collector-base
junction of the input clamping device. In addition to the clamping device action, there is lateral n-p-n parasitic transistor action. This
action is not destructive, and normal output states are reestablished when the input voltage returns to a value more positive than
− 0.3 V at TA = 25°C.
4. Short circuits between outputs to VCC can cause excessive heating and eventual destruction.
5. If the output transistors are allowed to saturate, the low-bias dissipation and the on-off characteristics of the outputs keep the
dissipation very small (usually less than 100 mW).
6. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can impact reliability.
7. The package thermal impedance is calculated in accordance with JESD 51-7.

DISSIPATION RATING TABLE

TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C
PACKAGE
POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING
J 1025 mW 8.2 mW/°C 656 mW 533 mW

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265





The LP239 is obsolete



   
   
and is no longer supplied.
SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004

recommended operating conditions

LP239 LP339 LP2901
UNIT
MIN MAX MIN MAX MIN MAX
VCC Supply voltage 3 30 3 30 3 30 V
VCC = 5 V 0 3 0 3 0 3 V
VIC Common-mode input voltage
VCC = 30 V 0 28 0 28 0 28 V
VCC = 5 V 0 3 0 3 0 3 V
VI Input voltage
VCC = 30 V 0 28 0 28 0 28 V
TA Operating free-air temperature −25 85 0 70 −40 85 °C

electrical characteristics, VCC = 5 V, TA = 25°C (unless otherwise noted)

PARAMETER TEST CONDITIONS TA† MIN TYP MAX UNIT
VCC = 5 V to 30 V, VO = 2 V, 25°C ±2 ±5
VIO Input offset voltage mV
RS = 0, See Note 6 Full range ±9
25°C ±0.5 ±5
IIO Input offset current nA
Full range ±1 ±15
25°C −2.5 −25
IIB Input bias current See Note 7 nA
Full range −4 −40
0 to
25°C
Common-mode input voltage VCC − 1.5
VICR Single supply V
range 0 to
Full range
VCC − 2
Large-signal differential voltage
AVD VCC = 15 V, RL = 15 kΩ 500 V/mV
amplification
VO = 2 V, 25°C 20 30
VI− = 1 V, See Note 8
Output sink current Full range 15 mA
VI+ = 0
VO = 0.4 V 25°C 0.2 0.7
VI+ = 1 V, VO = 5 V 25°C 0.1 nA
Output leakage current
VI− = 0 VO = 30 V Full range 1 µA
VID Differential input voltage VI ≤ 0 (or VCC − on split supplies) 36 V
ICC Supply current RL = ∞ all comparators 60 100 µA
† Full range is −25°C to 85°C for the LP239, 0°C to 70°C for the LP339, and − 40°C to 85°C for the LP2901.
NOTES: 8. VIO is measured over the full common-mode input voltage range.
9. Because of the p-n-p input stage, the direction of the current is out of the device. This current essentially is constant (i.e., independent
of the output state). No loading change exists on the reference or input lines as long as the common-mode input voltage range is
not exceeded.
10. The output sink current is a function of the output voltage. These devices have a bimodal output section that allows them to sink
(via a Darlington connection) large currents at output voltages greater than 1.5 V, and smaller currents at output voltages
less than 1.5 V.

switching characteristics, VCC = 5 V, TA = 25°C, RL connected to 5 V through 5.1 kΩ

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Large-signal response time 1.3
TTL logic swing, Vref = 1.4 V µs
Response time 8

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3








   
    The LP239 is obsolete
and is no longer supplied.
SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004

APPLICATION INFORMATION

Figure 1 shows the basic configuration for using the LP239, LP339, or LP2901 comparator. Figure 2 shows the
diagram for using one of these comparators as a CMOS driver.

VCC
VCC

30 kΩ 100 kΩ
IN + + + 3
IN + OUT
OUT
IN − − IN − −
12
1/4 LP239, LP339,
or LP2901
1/4 LP239, LP339, 1/4 SN54/74LS00 or
or LP2901 1/4 SN54/74ALS1000A

Figure 1. Basic Comparator Figure 2. CMOS Driver

All pins of any unused comparators should be grounded. The bias network of the LP239, LP339, and LP2901
establishes a drain current that is independent of the magnitude of the power-supply voltage over the range of
2 V to 30 V. It usually is necessary to use a bypass capacitor across the power supply line.
The differential input voltage may be larger than VCC without damaging the device. Protection should be
provided to prevent the input voltages from going negative by more than −0.3 V. The output section has two
distinct modes of operation: a Darlington mode and ground-emitter mode. This unique drive circuit permits the
device to sink 30 mA at VO = 2 V in the Darlington mode and 700 µA at VO = 0.4 V in the ground-emitter mode.
Figure 3 is a simplified schematic diagram of the output section. The output section is configured in a Darlington
connection (ignoring Q3). If the output voltage is held high enough (above 1 V), Q1 is not saturated and the
output current is limited only by the product of the hFE of Q1, the hFE of Q2, and I1 and the 60-Ω saturation
resistance of Q2. The devices are capable of driving LEDs, relays, etc. in this mode while maintaining an
ultra-low power-supply current of 60 µA, typically.

VCC

I1 = 6 µA

Q3

VO

Q1
Q2

Figure 3. Output-Section Schematic Diagram

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265





The LP239 is obsolete



   
   
and is no longer supplied.
SLCS004B − OCTOBER 1987 − REVISED SEPTEMBER 2004

APPLICATION INFORMATION

Without transistor Q3, if the output voltage were allowed to drop below 0.8 V, transistor Q1 would saturate, and
the output current would drop to zero. The circuit would be unable to pull low current loads down to ground or
the negative supply, if used. Transistor Q3 has been included to bypass transistor Q1 under these conditions
and apply the current I1 directly to the base of Q2. The output sink current now is approximately I1 times the
hFE of Q2 (700 µA at VO = 0.4 V). The output of the devices exhibits a bimodal characteristic, with a smooth
transition between modes.
In both cases, the output is an uncommitted collector. Several outputs can be tied together to provide a dot logic
function. An output pullup resistor can be connected to any available power-supply voltage within the permitted
power-supply range, and there is no restriction on this voltage, based on the magnitude of the voltage that is
supplied to VCC of the package.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5

 PACKAGE OPTION ADDENDUM

www.ti.com 6-Feb-2020

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LP2901D ACTIVE SOIC D 14 50 Green (RoHS NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901

& no Sb/Br)
LP2901DR ACTIVE SOIC D 14 2500 Green (RoHS NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901
& no Sb/Br)
LP2901DRE4 ACTIVE SOIC D 14 2500 Green (RoHS NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901
& no Sb/Br)
LP2901DRG4 ACTIVE SOIC D 14 2500 Green (RoHS NIPDAU Level-1-260C-UNLIM -40 to 85 LP2901
& no Sb/Br)
LP2901N ACTIVE PDIP N 14 25 Green (RoHS NIPDAU N / A for Pkg Type -40 to 85 LP2901N
& no Sb/Br)
LP339D ACTIVE SOIC D 14 50 Green (RoHS NIPDAU Level-1-260C-UNLIM 0 to 70 LP339
& no Sb/Br)
LP339DE4 ACTIVE SOIC D 14 50 Green (RoHS NIPDAU Level-1-260C-UNLIM 0 to 70 LP339
& no Sb/Br)
LP339DG4 ACTIVE SOIC D 14 50 Green (RoHS NIPDAU Level-1-260C-UNLIM 0 to 70 LP339
& no Sb/Br)
LP339DR ACTIVE SOIC D 14 2500 Green (RoHS NIPDAU | SN Level-1-260C-UNLIM 0 to 70 LP339
& no Sb/Br)
LP339DRE4 ACTIVE SOIC D 14 2500 Green (RoHS NIPDAU Level-1-260C-UNLIM 0 to 70 LP339
& no Sb/Br)
LP339DRG4 ACTIVE SOIC D 14 2500 Green (RoHS NIPDAU Level-1-260C-UNLIM 0 to 70 LP339
& no Sb/Br)
LP339N ACTIVE PDIP N 14 25 Green (RoHS NIPDAU N / A for Pkg Type 0 to 70 LP339N
& no Sb/Br)

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 6-Feb-2020

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF LP2901 :

• Automotive: LP2901-Q1

NOTE: Qualified Version Definitions:

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 17-Jul-2020

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LP2901DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LP2901DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LP339DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LP339DR SOIC D 14 2500 330.0 16.8 6.5 9.5 2.1 8.0 16.0 Q1
LP339DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LP339DRG4 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LP339DRG4 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 17-Jul-2020

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP2901DR SOIC D 14 2500 333.2 345.9 28.6
LP2901DR SOIC D 14 2500 367.0 367.0 38.0
LP339DR SOIC D 14 2500 367.0 367.0 38.0
LP339DR SOIC D 14 2500 364.0 364.0 27.0
LP339DR SOIC D 14 2500 333.2 345.9 28.6
LP339DRG4 SOIC D 14 2500 333.2 345.9 28.6
LP339DRG4 SOIC D 14 2500 367.0 367.0 38.0

Pack Materials-Page 2
 IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated