Scribd
Upload
146 views

Turbo Machine: Ioe, T C

The document discusses gas turbine nozzles and the flow through convergent, divergent, and convergent-divergent nozzles. It covers basic relations for properties like velocity and pressure as flow passes through a nozzle. Nozzle types include convergent, divergent, and convergent-divergent. Flow can be subsonic, sonic, or supersonic depending on the nozzle and operating conditions. The document also discusses nozzle performance parameters and variations in nozzle shape for applications like gas turbines and rocket propulsion.

Uploaded by

Calcgen Engineering
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
146 views

Turbo Machine: Ioe, T C

The document discusses gas turbine nozzles and the flow through convergent, divergent, and convergent-divergent nozzles. It covers basic relations for properties like velocity and pressure as flow passes through a nozzle. Nozzle types include convergent, divergent, and convergent-divergent. Flow can be subsonic, sonic, or supersonic depending on the nozzle and operating conditions. The document also discusses nozzle performance parameters and variations in nozzle shape for applications like gas turbines and rocket propulsion.

Uploaded by

Calcgen Engineering
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 35

DEPARTMENT OF AUTOMOBILE AND MECHANICAL ENGINEERING

IOE, THAPATHALI CAMPUS

TURBO MACHINE
CHAPTER 4
GAS TURBINE NOZZLES

1 Instructor : Achyut Paudel


Email: [email protected]
Ph: 9841263367
GAS TURBINE EXHAUST /NOZZLE

2
F-15 Eagle Nozzle 3
NOZZLE ENERGY EQUATION
 One dimensional steady state energy eqn:

 For isentropic conditions, assuming inlet and exit to be at same


datum;

 Inlet stagnation temperature

4
NOZZLE TYPES

 Convergent
 Divergent

 Convergent- Divergent (CD Nozzles/Laval Nozzle)

5
BASIC RELATIONS REVIEW
 C= Local speed of sound, M= local Mach No

 Fluid flow regimes are often described in terms of the


flow Mach Number. The flow is called sonic when M=1,
subsonic when M<1 , supersonic when M>1, hypersonic
when M>>1 and transonic when M nearly 1.

6
FLOW VELOCITY VS. FLOW AREA

 Subsonic condition: M<1, dA and dP same sign, area


decreases and pressure decreases ( velocity increases)
 Supersonic Condition: M>1, dA and dP opposite sign, area
increases and pressure decreases(velocity increases)
 Hence in case of a CD nozzle, throat area is so designed that
M=1 at throat and the flow is said to be choked. Pressure
does not reduce further until temperature is increased.
 Addition of a divergent part accelerates the gases to M>1 7
8
9
ISENTROPIC FLOW PROPERTY RELATIONS
 Subscript o represents stagnation properties, M= Mach
number, γ= sp. heat ratio

10
CRITICAL PROPERTIES
 The properties of a fluid at a location where the Mach number is
unity (the throat) are called critical properties, and the ratios are
called critical ratios. It is common practice in the analysis of
compressible flow to let the superscript asterisk (*) represent the
critical values.
 Putting M=1 in above equations:

11
12
ISENTROPIC FLOW THROUGH NOZZLES
 Convergent Nozzle

13
MASS FLOW RATE
 Steady- flow mass flow rate:

 Maximum mass flow rate at M=1

 Expression for throat area in terms of M:

14
Fig. 13.5 Variation of A/A* with Mach number
for isentropic flow of an ideal gas with γ= 1.4. 15
16
NUMERICAL EXAMPLE:
 A converging nozzle, with a throat area of 0.001 m2, is operated with
air at a back pressure of 591 kPa (abs). The nozzle is fed from a
large plenum chamber where the absolute stagnation pressure and
temperature are 1.0 MPa and 60 0C. The exit Mach number and
mass flow rate are to be determined.
Ans:
M= 0.9
m = 2.2 kg/s

17
18
19
FLOW THROUGH C-D NOZZLE

20
21
22
23
24
 Figure (a) shows the flow through the nozzle when it is completely
subsonic (i.e. nozzle isn't choked). The flow accelerates out of the
chamber through the converging section, reaching its maximum
(subsonic) speed at the throat. The flow then decelerates through the
diverging section and exhausts into the ambient as a subsonic jet.
Lowering the back pressure in this state increases the flow speed
everywhere in the nozzle.

 Further lowering pb results in figure (b). The flow pattern is exactly the
same as in subsonic flow, except that the flow speed at the throat has
just reached Mach 1. Flow through the nozzle is now choked since
further reductions in the back pressure can't move the point of M=1
away from the throat. However, the flow pattern in the diverging
section does change as the back pressure is lowered further.

 As pb is lowered below that needed to just choke the flow a region of


supersonic flow forms just downstream of the throat. Unlike a subsonic
flow, the supersonic flow accelerates as the area gets bigger. This region
of supersonic acceleration is terminated by a normal shock wave. The
shock wave produces a near-instantaneous deceleration of the flow to
subsonic speed. This subsonic flow then decelerates through the
remainder of the diverging section and exhausts as a subsonic jet. In
this regime if the back pressure is lowered or raised the length of
supersonic flow in the diverging section before the shock wave increases
or decreases, respectively.
 If pb is lowered enough the supersonic region may be extended all
the way down the nozzle until the shock is sitting at the nozzle exit,
figure (d). Because of the very long region of acceleration (the entire
nozzle length) the flow speed just before the shock will be very large.
However, after the shock the flow in the jet will still be subsonic.
 Lowering the back pressure further causes the shock to bend out
into the jet, figure (e), and a complex pattern of shocks and
reflections is set up in the jet which will now involve a mixture of
subsonic and supersonic flow, or (if the back pressure is low enough)
just supersonic flow. Because the shock is no longer perpendicular to
the flow near the nozzle walls, it deflects it inward as it leaves the
exit producing an initially contracting jet. We refer to this as over-
expanded flow because in this case the pressure at the nozzle exit
is lower than that in the ambient (the back pressure)-i.e. the flow
has been expanded by the nozzle too much.
 A further lowering of the back pressure changes and weakens the
wave pattern in the jet. Eventually, the back pressure will be
lowered enough so that it is now equal to the pressure at the nozzle
exit. In this case, the waves in the jet disappear altogether, figure
(f), and the jet will be uniformly supersonic. This situation, since it26
is
often desirable, is referred to as the 'design condition‘, Pe=Pa.
 Finally, if the back pressure is lowered even further we will
create a new imbalance between the exit and back pressures
(exit pressure greater than back pressure), figure (g). In this
situation, called under-expanded, expansion waves that
produce gradual turning and acceleration in the jet form at
the nozzle exit, initially turning the flow at the jet edges
outward in a plume and setting up a different type of complex
wave pattern.

Summary Points to Remember:


 When the flow accelerates (sub or supersonically) the pressure
drops
 The pressure rises instantaneously across a shock
 The pressure throughout the jet is always the same as the
ambient (i.e. the back pressure) unless the jet is supersonic
and there are shocks or expansion waves in the jet to produce
pressure differences
 The pressure falls across an expansion wave
27
NOZZLE ISENTROPIC EFFICIENCY
 The nozzle isentropic
efficiency is defined
as:

28
NUMERICAL EXAMPLE
 Air flows isentropically in a converging-diverging nozzle, with exit
area of 0.001 m2. The nozzle is fed from a large plenum where the
stagnation conditions are 350K and 1.0 MPa (abs). The exit pressure
is 954 kPa (abs) and the Mach number at the throat is 0.68. Fluid
properties and area at the nozzle throat and the exit Mach number
are to be determined.

29
30
31
NOZZLE SHAPE VARIATIONS

32
C-D NOZZLE FOR ROCKET PROPULSION

 Where F is the
thrust developed.
 In case the exit
pressure is equal
to ambient
pressure,
pressure thrust
equals zero.

33
NOZZLE DESIGN PARAMETERS

 Expansion Area Ratio: Most important parameter in


nozzle design is expansion area ratio,

 Fixing other variables (primarily chamber pressure) →


only one ratio that optimizes performance for a given
altitude (or ambient pressure)
 However, rocket does not travel at only one altitude
 Select expansion ratio that maximizes performance over
a range of ambient pressures
 Other factors must also be considered: Nozzle weight,
length, manufacturability, cooling (heat transfer), and 34
aerodynamic characteristics.
ROCKET PROPULSION NOZZLE SHAPE VARIATION
 Cone
 Bell

 Annular

35

You might also like