DESIGN OF END PLATE MOMENT CONNECTION (AS PER AISC FOR TENSION BOLT END PLATE CONNECTION DESIGN)

ASpectrum Designs Plus Engineering Services Project Title: Proposed Two Store Residential Building
Address: 8487 Sandoval Avenue, Pinagbuhatan, Pasig City 1602 Project Location: Villa Cuana Phase 1, Pinagbuhata, Pasig City 1602
Contact: 09982028893 Structural Engineer: Engr. Andro S Rebuyas, RCE, ME-1, RMP, M.Eng-SE
Gmail add: [email protected] Membership: M.PICE, M.ASCE, M.PAMEA, M.FPEA, M.PSUMP, M.NAMPAP, M.SEAD

BEAM DATA

Beam W4x13 C.L. STAAD Input

End Plate
("tp" x "Bp" x "Lp") Member Forces
2
Fy = 248 N/mm E
M= 118.112 kN-m Moment
Pf A= 31.165 kN Axial
S
D 10.57 cm Depth V= 87.405 kN Shear
(Beam)
fw = 10.31 cm Flange Width
P
ft = 0.88 cm Flange Thickness M Node 140
Wt = 0.71 cm Web Thickness R Member 1179
3
tw= 89.0 cm Section Modulus LC 182
2 S
Pf
Zxx = 24.71 cm Sectional Area
2 E
Af = 9.04 cm Area of Tension Flange
2
"Nb" - "db" Bolts
Aw = 6.64 cm Area of Web on "g" Gage

LOAD DATA

Ma = 14.57 kN-m Moment Capacity, (Ma =0.66Fy x Zxx) Gb = 10.9 Grade of Bolts
Design for 90.0% Capacity db = 24 mm Diameter of Bolts
M= 13.11 kN-m Design Moment Tb = 4 Number of Tension Bolts
10 Total Number of Bolts
Tc = 275.8 kN Axial Capacity, (Ta = 0.45Fy x As)
P= 31.17 kN Axial Force Ft = 357 N/mm2 Tensile Stresss
Fv = 238 N/mm2 Shear Stress
Vc = 65.83 kN Shear Capacity, (Va =0.40Fy x Aw)
2
Design for 40.0% Capacity Root Area of Bolt = 366.58 mm
V= 26.33 kN Design Shear
Capacity of Bolt
Check for Combined Moment and Tension Tension, Tc = 130.87 kN
Interaction Ratio = M/Ma + T/Tc Shear, Vc = 87.25 kN

1.01 >1.0, REVISE

BOLT CHECK

Tension Check Shear Check Check for Combined Tension & Shear

Flange Force, Ff = (M/ Nominal Depth) + (P*Af/As) f v = V/ nos of bolts Interaction Ratio = T/Tc + f v/Vc

Ff = 135.51 kN

Tension in bolt, T = 33.88 kN < Ten Capacity, OK Ff = 2.63 kN < Shear Capacity, OK 0.29 <1.4, OK

END PLATE CALCULATIONS, FLANGE FILLET AND WEB FILLET CALCULATIONS

End Plate Calculations Flange Fillet Calculations

Pf = 50 mm 1st row of bolts from flange Flange Fillet reqd, w = Ff / sw(2(fw+tf)-tw)

db = 24 mm Diameter of Bolt
w= 12 mm Weld Thickness sw = 110 N/mm2
w= 8.04 mm
Pe = Pf - (db/4) - .707w Effective bolt distance
Pe = 35.52 mm Hence Provide,
8.04 mm Flange fillet weld
bp = 180 Width of End of Plate -
Ca = 1.13
Cb = 0.76 Web Fillet Calculations
(Af/Aw)1/3 = 1.11
1/4
(Pe/db) = 1.10 web Fillet reqd, w = 0.60Fy tw / sw

1/3 1/4
am = Ca Cb (Af/Aw) (Pe/db) w= 6.8 mm < web thk, Fillet weld is OK
am = 1.05
Hence Provide,
Me = am Ff Pe/4 10.0 mm thk web weld
Me = 1.26 kN-m

tp = sq rt (6Me /0.75Fy bp) Plate Thickness Required

tp = 15.02 mm

Provide 25 mm thk Plate

 COLUMN DATA AND CHECKS FOR COLUMN SECTION

Column Data Check for Column Yeilding

Column UC 305x305x158 Flange force for Check = 5/3 * Flange Force

2
Fy = 250 N/mm 40 ksi Ff = 135.51 kN
Pbf = 225.86 kN
D= 327.00 mm 12.87 inch Depth
fw = 311.00 mm 12.24 inch Flange Width Pbf allow = Fyc x twc x (tfb+ 6k + 2 tp + 2w)
tf = 25.00 mm 0.98 inch Flange Thickness
twc = 15.8 mm 0.62 inch Web Thickness Pbf allow = 1,274.9 kN > Pbf, OK
k= 40.00 mm 1.57 inch
dc = 247.00 mm 9.72 inch Effective depth Check for Column web buckling

2
As = 203.40 cm Sectional Area Pbf allow = 4100 x twc3 x sqrt(fyc) / dc Imperical Formulae
2
Af = 77.75 cm Area of Web
2
Aw = 47.90 cm Pbf allow = 641.8 kips
Pbf allow = 2,917.4 kN > Pbf, OK
tfb = 8.76 mm 0.35 inch Thickness of Beam Flange
tp = 25 mm 0.98 inch Thickness of End Plate Check for Column flange bending opposite Tension Flange
w= 12 mm 0.47 inch Weld Thickness
g= 100 mm
Design Result db = 24 mm Diameter of Bolt
C= 125 mm Vertical Distance between rows of Bolts
k1 = 23 mm

Pe = (g/2) - (db/4) - .k1

Pe = 20.90 mm

bs = 313 Effective Width of Column Flange

Ca = 1.13
Cb = 1.00
(Af/Aw)1/3 = 1.18
(Pe/db)1/4 = 0.97

1/3 1/4
am = Ca Cb (Af/Aw) (Pe/db)
am = 1.28

Me = am Ff Pe/4
Me = 0.91 kN-m

tfc = sq rt (6Me /0.75Fy bs) Required Flange Thickness

tfc = 9.63 mm < 25 mm, Hence Stiffeners not Reqd

This Spreadsheets is licensed only to Engr. Andro S. Rebuyas, RCE, ME-1, RMP, M.Eng-SE